Cisco cBR-8 Quick Reference Software Release Information

Hardware and Installation

 8 Cable Line Card slots with integrated N+1 RF-Switch Slot2 (RF Linecard) Slot2 (RFPIC)
 768 Downstream + 96 Upstream D3.0 narrowcast Slot 3 (RF Linecard) Slot 3 (RFPIC) FAN1
Channels per linecard - 8 DS X 16 US Port Slot 4 (SUP) Slot 4 (SUPPIC)
 16 x 192 MHz OFDM blocks + Full D3.0 per linecard (w/ FAN2
DS 3.1 PHY Module) Slot 5 (SUP) Slot 5 (SUPPIC)
 32 x 96 MHz OFDMA blocks + Full D3.0 per linecard (w/
FAN3
US 3.1 PHY Module) Slot 6 (RF Linecard) Slot 6 (RFPIC)
 64 Service Groups / 56 SG with N+1 Slot 7 (RF Linecard) Slot 7 (RFPIC)
 200Gbps Aggregate Forwarding with Integrated 8 + 8 Slot 8 (RF Linecard) Slot 8 (RFPIC) FAN4
10GigE backhaul with initial hardware Slot 9 (RF Linecard) Slot 9 (RFPIC)
 6 PEM up to 9kW : 4+1 DC or 3+1 or 3+3 AC
PEM0 PEM1 PEM2 Power Shelf
 FCS HW with 3.1 modules facilities requirement 8kW (PowerSwitch, Power Plugs)
PEM3 PEM4 PEM5
Sample Video Config
Field Chassis Front Chassis Back
Replaceable interface VirtualPortGroup0
PHY ip address [Link] [Link] Troubleshooting
Modules
cable video System
multicast-uplink Port-channel1 access-list SSMrange - Register the cBR-8 smart licensing
mgmt-intf VirtualPortGroup 0 license smart register idtoken <>
Sample DS/US Phy Config Sample OFDM Channel Profile
encryption - View licensing status and information
linecard 1/0 ca-system powerkey scrambler des show license [all] [summary]
With Video & DOCSIS3.1 service-distribution-group lc1_p0 id 1 - Status and detailed firmware for cards and components
cable downstream ofdm-chan-profile 102 rf-port integrated-cable 1/0/0 show platform [diag]
controller Integrated-Cable 1/0/0
cyclic-prefix 1024 virtual-carrier-group vcg_gqi_1-0 id 1 - Field Programmable Device (FPD) CLIs
max-ofdm-spectrum 96000000
interleaver-depth 16 encrypt show hw-module all fpd
max-carrier 32
pilot-scaling 48 service-type narrowcast show upgrade fpd progress
base-channel-power 39
roll-off 128 rf-channel 24-31 tsid 10024-10031 output-port- upgrade hw-module …
rf-chan 0 23
subcarrier-spacing 50KHZ number 1-8 - Linecard console access
type DOCSIS
profile-control modulation-default bind-vcg request platform software console attach <>
frequency 537000000
1024-QAM vcg vcg_gqi_1-0 sdg lc1_p0 - Linecard reloads via CLI
rf-output NORMAL
profile-ncp modulation-default 16- logical-edge-device led-1 id 1 hw-module slot <> reload
power-adjust 0
QAM protocol gqi - Crashinfo stored on harddisk: and/or bootflash:
qam-profile 1
profile-data 1 modulation-default mgmt-ip [Link] - Important Directories for fault data collection
docsis-channel-id 1 dir harddisk:core
2048-QAM mac-address a46c.2ab0.2c01
rf-chan 24 31 dir harddisk:tracelogs
profile-data 2 modulation-default server [Link]
type VIDEO
4096-QAM
Sample OFDM Channel Profile dir harddisk:bay<>-obfl
virtual-edge-input-ip [Link] input-port-
frequency 489000000 - Overall system CPU / Memory usage – command without platform keyword will provide IOSd process only
number 1
rf-output NORMAL show process [cpu|memory] platform
vcg vcg_gqi_1-0
power-adjust 0
active
qam-profile 4 Data path
rf-chan 158
power-adjust 0
Supported - Global FP drop stats
show platform hardware qfp active statistics drop detail [clear]
docsis-channel-id 159 Base Channel - Global FP punt stats
ofdm channel-profile 102 start-frequency show platform hardware qfp active infrastructure punt summary
678000000 width 96000000 plc 723000000 Power ranges [clear]
in dBmV by # - Per-CM queue
controller Upstream-Cable 1/0/0 show platform hardware qfp active feature qos queue output
us-channel 0 frequency 17600000 SC-QAMs and interface CM<MD>:<sid>
us-channel 0 channel-width 6400000 6400000 OFDM - Per-CM detailed QoS
us-channel 0 docsis-mode atdma show cable modem <> c3pl
us-channel 0 minislot-size 1 bandwidth - Queue status and stats
us-channel 0 modulation-profile 221 show cable dp queue <wideband-cable|integrated-cable>
us-channel 0 equalization-coefficient
no us-channel 0 shutdown DOCSIS
- Verify downstream PHY state
Patching show controllers integrated-cable <> rf-port
Load System in Sub-Package Mode show cable card <> ds-phy display

- Expand the consolidated binary to a specific directory - Verify per RF-channel state
Patching capability requires Sub-Package mode operation
request platform software package expand file bootflash:<> to bootflash:/DIR show controllers integrated-cable <> rf-channel <>
 Extract image using request platform software package expand - Configure boot system parameter to point to [Link] file in the appropriate directory - Verify downstream MAC state
 DO NOT FORGET to repeat on the Standby SUP boot system bootflash:/DIR/[Link]
- Get current version for each packages per device
show cable mac-domain <> cgd-associations
 Along with sub-package extraction a [Link] file is created show platform software patch <slot|R0|R1|F0|F1> info
show cable mac-domain <> mdd
- Verify upstream PHY state
 Boot commands point to the [Link] file instead of the .bin file - Apply patch per the detailed instructions in readme
show controllers upstream-Cable <> us-channel <>
request platform software package install <node|rp 0|1> file <>
 Applying a patch will update [Link] file - Trigger process restart on Cable LC - Total per-channel utilization
 Linecard patches can make use of process restart request platform software process restart show controller integrated-cable <> counters rf-channel