Scribd
Upload
36 views

Flare Fitting (45°), Cap, Brass: Specification Requirements

This document contains specifications for brass flare fittings with 45-degree angles in various nominal pipe sizes. It lists dimensional requirements for each size, including thread dimensions, drill depth, and nut height tolerances. Material requirements specify brass composition in accordance with RoHS standards. Thread and finish specifications adhere to ASME B1.20.3 NPTF and plain standards. Revision notes list changes made between versions.

Uploaded by

Shubham
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
36 views

Flare Fitting (45°), Cap, Brass: Specification Requirements

This document contains specifications for brass flare fittings with 45-degree angles in various nominal pipe sizes. It lists dimensional requirements for each size, including thread dimensions, drill depth, and nut height tolerances. Material requirements specify brass composition in accordance with RoHS standards. Thread and finish specifications adhere to ASME B1.20.3 NPTF and plain standards. Revision notes list changes made between versions.

Uploaded by

Shubham
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Page 1 of 2 Fastenal Product Standard REV-02

Date: April 28, 2020 FF.CAP.BRS

Flare Fitting (45°), Cap, Brass


This product standard contains the required dimensional, mechanical, performance, and chemical characteristics of the products shown
in this purchase order (as applicable to the product). Unless specified below, current revisions of national or international standards
shall be applicable as of the date of Fastenal’s purchase order and must be adhered to in their entirety. If the order received does not
meet these requirements, corrective action may be issued which could jeopardize your status as an approved supplier to Fastenal.

B C D I J U T L
Nominal Straight Full Wrench
Hex Dia. Drilll Depth Dia. Nut Height
Pipe Size Thread Thread Height
Nom. +/- 0.010 +/- 0.010 +/- 0.010 Min. Max. Min. Min. +/- 0.010
3/16 3/8-24 1/2 0.12 0.28 0.21 0.41 0.39 0.27 0.47
1/4 7/16-20 9/16 0.19 0.34 0.25 0.47 0.45 0.40 0.53
5/16 1/2-20 5/8 0.22 0.38 0.29 0.53 0.51 0.40 0.62
3/8 5/8-18 3/4 0.28 0.44 0.34 0.67 0.64 0.46 0.69
1/2 3/4-16 7/8 0.41 0.53 0.43 0.80 0.77 0.52 0.84
5/8 7/8-14 1-1/16 0.50 0.66 0.54 0.93 0.90 0.62 0.97
3/4 1-1/16-14 1-5/16 0.62 0.78 0.66 1.11 1.08 0.74 1.09

Specification Requirements:

• Dimensions: SAE J513 (010112) All dimensions not shown above


shall comply with the general requirements of SAE J513
• Material: UNS C36000, C34500 or C35000 Brass, In compliance with
current RoHS European Union Directive. In addition,
minimum Copper content 57%, maximum alloying elements
5%, remainder zinc
• Thread Requirements: ASME B1.20.3 NPTF
• Finish: Plain, as processed

RECORD OF REVISION CHANGES TO THIS DOCUMENT ARE LOCATED ON THE


LAST PAGE
Page 2 of 2 Fastenal Product Standard REV-02
Date: April 28, 2020 FF.CAP.BRS

Revision Level Changes to this Document

Revision Revision
Document Name Rationale for Revision
Level Date
FF.CAP.BRS 02 4/28/2020 Revised image, RoHS, and finish requirements.

The rationale above may not include all of the changes within each revision. A complete
review of the Fastenal Product Standard is required.

You might also like