Scribd
Upload
1K views

Svmpc1: Installation Manual

The document provides installation instructions for the SVMPC1 controller in 3 steps: 1. Check equipment and network requirements. This includes verifying the DTA116A51 device is installed and networked, indoor unit addresses are set, and the network can use DHCP. 2. Set up the network parameters and connect the SVM controller. This involves getting network information, setting the WiFi router's DHCP range if needed, using software to find the SVM's IP address, and configuring network, time zone and device connection settings via a web interface. 3. Connect the DTA116A51 to the SVM controller using an RS485 to USB converter cable and reboot the SVM controller to complete the installation.

Uploaded by

lucio ruiz jr
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
1K views

Svmpc1: Installation Manual

The document provides installation instructions for the SVMPC1 controller in 3 steps: 1. Check equipment and network requirements. This includes verifying the DTA116A51 device is installed and networked, indoor unit addresses are set, and the network can use DHCP. 2. Set up the network parameters and connect the SVM controller. This involves getting network information, setting the WiFi router's DHCP range if needed, using software to find the SVM's IP address, and configuring network, time zone and device connection settings via a web interface. 3. Connect the DTA116A51 to the SVM controller using an RS485 to USB converter cable and reboot the SVM controller to complete the installation.

Uploaded by

lucio ruiz jr
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

SVMPC1

Installation Manual
Ver.2.0
Jul. 28th 2018

SVMIM-C1
1
Before Installation
Before install SVMPC1, please check below things.

(1) Confirm below equipment are prepared.


• SVM controller
• AC adaptor for SVM controller
• RS485-USB converter
• LAN cable (for SVM controller to WiFi router connection)

Figure 1: SVMPC1 equipment

(2) Check if DTA116A51 is installed to VRV system.


RS485 cable has to be run from DTA116A51 to the place to install SVM controller.
DTA116A51 communication setting has to be set as below.
• Communication speed: 19200bps
• Stop bit: 1 DS1 DS2
• Parity: EVEN
• Address: 1
1 2 3 4 1 2 3 4
Figure 2: DTA116A51 dip switch settings

(3) Check if VRV indoor units are set D3 address.

(4) Check network environment.


SVMPC1 requires internet connection for clock synchronization of SVM controller.
Please check if SVM controller can connect to internet accessible network.
If SVM controller does not have internet accessibility, schedule function will not
work at the correct time.

Additionally, please check if the network can use DHCP (automatic address
assigning) function. SVM controller does not have IP address at the initial.
Therefore, if the network cannot use DHCP, no one can access to the SVM controller
on the network. In such case, other network is necessary to setup network parameter.
After setup network parameter for the SVM controller, DHCP function does not
necessary for the network.

SVMIM-C1
2
Installation Procedure
Please follow installation procedure to install and setup SVM.

1: Get network information and decide network parameters for SVM


controller .
(A) Please get below network parameters for SVM controller to connect to
customer’s network(LAN).
• IP address
• Netmask
• Default Gateway
• DNS server IP address
(B) If WiFi connection is used, please get below WiFi access parameters also.
• SSID
• PIN code
(C) If there are no person managing the network.
Almost of the cases, WiFi router is used in a default setting. In such case, you
can get network information with below procedure.

1: Connect your PC to the network using WiFi


SSID and password is described on the back panel of the WiFi router.
If these parameters is changed, please ask to customer.
2: Confirm network setting of your PC and take a note of below parameters.
• IP address – (i)
• Netmask – (ii)
• Default Gateway – (iii)
• DNS server IP address – (iv)

3: Decide SVM controller network parameters.


You have to decide SVM controller network parameter like below.
• IP address for SVM controller: use part of IP address(i)
IP address (i) . . .

IP address for SVM controller . . .2


• Netmask for SVM controller: use same value of Netmask (ii)
• Default Gateway for SVM controller: user same value of Gateway(iii)
• DNS server IP address for SVM controller: user same value of DNS server(iv)

* If the last digit of IP address (i) is less than 20, WiFi router setting has
to change. Please refer “2: WiFi router setting” (P.3).
Check if last digit is less
IP address (i) . . . than 20 or not.

SVMIM-C1
3
2: WiFi router setting
(1) Connect your PC with WiFi to WiFi router.
(2) Open Web browser on your PC and access to WiFi router IP address.
Usually, WiFi router IP address is a Default Gateway address.
Or please refer WiFi router manual.
(3) Login in with administrator user. (Please refer WiFi router manual)
(4) Check DHCP address range and modify it.
If starting address is “XXX.XXX.XXX.2” then it should change to
“XXX.XXX.XXX.20”.

Example: In the case of ASUS RT-N12 Wireless N Router


(1) Access to http://192.168.1.1 on your Web browser.
(2) Login with below user and password.
User: admin
Password: admin
(3) Under “Advanced Settings” on the left menu, select “LAN”. Click on “DHCP
Server” on the tabs on top, then change “IP Pool Starting Address”.

(4) After changing, scroll down and click “Apply” to save setting.

Example: In the case of TP-LINK 300Mbps Wireless N Nano Router


(1) Access to http://tplinkwifi.net/ on your Web browser.
(2) Login with below user and password.
User: admin
Password: admin
(3) Select “DHCP” on the left menu, then change “Start IP Address”.

(4) After changing, click “Save” to save setting.

SVMIM-C1
4
Example: In the case of D-Link DWR-116
(1) Access to http://192.168.0.1/ on your Web browser.
(2) Login with below user and password.
User: admin
Password: <blank>
(3) Under “SETUP”, select “NETWORK SETTINGS” on the left menu.
(4) Scroll down and change “DHCP IP Address Range”.

(4) After changing, click “Save Settings” to save setting.

3: Service setting for SVM controller


(1) Connect your PC and SVM controller to customer’s LAN.

(2) Double click on the “FindSVM.exe” program provided.

(3) “FindSVM.exe” program screen should appear. The new SVM should show up
in the screen. Take note of the IP address.

(4) Open Web browser on your PC and access to “IPaddress/service/”, with the IP
address from earlier. It will be shown service setup screen as below.

Connection of SVM controller and your PC to customer’s LAN


Customer’s LAN

“FindSVM.exe” program screen Service setup screen

In the example shown above, the service setup screen


can be accessed from a web browser using
“192.168.1.98/service”.

SVMIM-C1
5

Network setting Network setting screen


(1) Click “Network Setup” on the service setup screen,
then Network Setting screen will be appeared.

(2) Type network parameter for the SVM controller on


the Network Setting screen and click “Set” button.

The IP address can be used to access this SVM


controller from PC and smart phone after reboot the
SVM controller.

WiFi setting
(1) If WiFi connection is used, click “WiFi setup(SSID)
on the service setup screen. Then WiFi setting WiFi setting screen
screen will be appeared.

(2) Type SSID and PIN code to access with WiFi on


the WiFi setting screen and click “set” button.

Timezone setting
(1) Click “Timezone Setup” on the service setup
screen, then Timezone setting screen will be Timezone setting screen
appeared.

(2) Select timezone from the list and click “Set” button.
This setting is important to synchronize SVM
controller clock and for schedule function.

Please refer SVM Service Setup manual Ver3.2 for


other settings.

SVMIM-C1
6

Device Connection setting Device connection setting screen


(1) Click “Controller Connection Setup” on the service
setup screen, then device connection setting
screen will be appeared.

(2) Under “USB port connection devices”, click on


“Add” next to DTA116A51. The Device ID should be
“1” and the USB port should be “USB1”.

(3) Click on “Save” on the bottom of the screen to save


all edited settings.

*Note: SVM supports two DTA116A51 connections. If


two DTA116A51 connections are required, ensure the
first DTA116A51 connection Device ID is “1” and USB
port is “USB1”, and the second DTA116A51
connection Device ID is “2” and USB port is “USB2”.

Smart Meter
If smart meter is required, click on “Add” next to
Smart Meter. Connect the Smart Meter USB
connection to USB2 if there is only one DTA116A51
connection, or to USB3 if there are two DTA116A51
connections.

Ensure the “USB port” setting is the same as the


connected port as shown in “Figure 4: DTA116A51
USB Connection to SVM controller” on page 5.

Reboot SVM controller Reboot SVM controller


After setting, please reboot the SVM controller to
run with the setting.

Click on the Reboot button to reboot SVM controller.

SVMIM-C1
7
3: Connect DTA116A51 to SVM controller by RS485-USB converter
(1) Connect RS485 cable from DTA116A51 to RS485-USB converter.
RS485 cable has polarity. Please care +/- of the connector.
(2) Insert first RS485-USB converter to USB1 port of SVM controller.
*If second DTA116 connection is required, insert second converter to USB2 port.
(3) Reboot SVM controller.

Network USB ports


B D-

A[+] B[-]
USB1 USB2
A D+
USB3 USB4
RS485-USB converter

Back side of SVM controller DTA116A51

Figure 4: DTA116A51 USB Connection to SVM controller

4: Operation confirmation by using tablet


(1) Open web browser on a tablet and type IP address of SVM controller.
(2) When “Login screen” is appeared then login with “admin” user.
(3) Check if all connected indoor units are shown on the screen.
If all indoor units are not shown, please check the indoor unit is supplied power
and set D3 address.
(4) Set name of all indoor units and select icon.

5: Explain to customer
Please explain to customer how to access and how to use SVMPC1.

SVMIM-C1

You might also like