WORKSHOP PRACTICE (Fitting Shop)

FITTING WORKSHOP
1.1 INTRODUCTION
Machine tools are capable of producing work at a faster rate, but, there are occasions when
components are processed at the bench. Sometimes, it becomes necessary to replace or repair
component which must be fit accurately with another component on reassembly. This involves a
certain amount of hand fitting. The assembly of machine tools, jigs, gauges, etc, involves certain
amount of bench work. The accuracy of work done depends upon the experience and skill of the
fitter. The term ‘bench work’ refers to the production of components by hand on the bench,
where as fitting deals which the assembly of mating parts, through removal of metal, to obtain
the required fit. Both the bench work and fitting requires the use of number of simple hand tools
and considerable manual efforts. The operations in the above works consist of filing, chipping,
scraping, sawing drilling, and tapping.

1.2 HOLDING TOOLS

1.2.1 Bench vice
The bench vice is a work holding device. It is the most commonly used vice in a fitting shop.
The bench vice is shown in Figure 1.1.

It is fixed to the bench with bolts and nuts. The vice body consists of two main parts, fixed jaw
and movable jaw. When the vice handle is turned in a clockwise direction, the sliding jaw forces
the work against the fixed jaw. Jaw plates are made of hardened steel. Serrations on the jaws
ensure a good grip. Jaw caps made of soft material are used to protect finished surfaces, gripped
in the vice. The size of the vice is specified by the length of the jaws. The vice body is made of
cast Iron which is strong in compression, weak in tension and so fractures under shocks and
therefore should never be hammered.

KFUEIT Page 1
1.2.2 V‐block
V‐block is rectangular or square block with a V‐groove on one or both sides opposite to each
other. The angle of the ‘V’ is usually 900. V‐block with a clamp is used to hold cylindrical work
securely, during layout of measurement, for measuring operations or for drilling for this the bar
is faced longitudinally in the V‐Groove and the screw of V‐clamp is tightened. This grip the rod
is firm with its axis parallel to the axis of the v‐groove.
1.2.3 C‐Clamp
This is used to hold work against an angle plate or v‐block or any other surface, when gripping is
required. Its fixed jaw is shaped like English alphabet ‘C’ and the movable jaw is round in shape
and directly fitted to the threaded screw at the end .The working principle of this clamp is the
same as that of the bench vice.

1.3 MARKING AND MEASURING TOOLS

1.3.1 Surface plate
The surface plate is machined to fine limits and is used for testing the flatness of the work piece.
It is also used for marking out small box and is more precious than the marking table. The degree
of the finished depends upon whether it is designed for bench work in a fitting shop or for using
in an inspection room; the surface plate is made of Cast Iron, hardened Steel or Granite stone. It
is specified by length, width, height and grade. Handles are provided on two opposite sides, to
carry it while shifting from one place to another.

Figure 1.4: Surface plate Figure 1.5: Angle plate

1.3.2 Try square

It is measuring and marking tool for 900 angle .In practice, it is used for checking the squareness
of many types of small works when extreme accuracy is not required .The blade of the Try
square is made of hardened steel and the stock of cast Iron or steel. The size of the Try square is
specified by the length of the blade.

1.3.3 Scriber

A Scriber is a slender steel tool, used to scribe or mark lines on metal work pieces. It is made of
hardened and tempered High Carbon Steel. The Tip of the scriber is generally ground at 12oto
15o . It is generally available in lengths, ranging from 125mm to 250mm .It has two pointed ends
the bent end is used for marking lines where the straight end cannot reach.

Figure 1.6: Try square Figure 1.7: Scriber

1.3.4 Odd leg Caliper

This is also called ‘Jenny Caliper’ or Hermaphrodite. This is used for marking parallel liners
from a finished edge and also for locating the center of round bars; it has one leg pointed like a
divider and the other leg bent like a caliper. It is specified by the length of the leg up to the hinge
point.

1.3.5 Divider

It is basically similar to the calipers except that its legs are kept straight and pointed at the
measuring edge. This is used for marking circles, arcs laying out perpendicular lines, by setting
lines. It is made of case hardened mild steel or hardened and tempered low carbon steel. Its size
is specified by the length of the leg.
 Figure 1.8: Odd leg calliper and divider

1.3.6 Trammel
Trammel is used for drawing large circles or arcs.

1.3.7 Punches
These are used for making indentations on the scribed lines, to make them visible clearly. These
are made of high carbon steel. A punch is specified by its length and diameter (say as 150’
12.5mm). It consists of a cylindrical knurled body, which is plain for some length at the top of it.
At the other end, it is ground to a point. The tapered point of the punch is hardened over a length
of 20 to 30mm.

Dot punch is used to lightly indent along the layout lines, to locate center of holes and to provide
a small center mark for divider point, etc. for this purpose, the punch is ground to a conical point
having 60° included angle.

Center punch is similar to the dot punch, except that it is ground to a conical point having 90°
included angle. It is used to mark the location of the holes to be drilled.

Figure 1.9: Punches

1.3.8 Calipers
They are indirect measuring tools used to measure or transfer linear dimensions. These are used
with the help of a steel Rule to check inside and outside measurements. These are made of Case
hardened mild steel or hardened and tempered low carbon steel. While using, but the le gs of the
caliper are set against the surface of the work, whether inside or outside and the distance between
the legs is measured with the help of a scale and the same can be transferred to another desired
place. These are specified by the length of the leg. In the case of outside caliper, the legs are bent
inwards and in the case of inside caliper, the legs bent outwards.

Figure 1.10: Calipers

1.3.9 Vernier Calipers
These are used for measuring outside as well as inside dimensions accurately. It may also be
used as a depth gauge. It has two jaws. One jaw is formed at one end of its main scale and the
other jaw
is made part of a vernier scale.

Figure 1.11: Vernier caliper

1.4 CUTTING TOOLS

1.4.1 Hack Saw
The Hack Saw is used for cutting metal by hand. It consists of a frame, which holds a thin blade,
firmly in position. Hacksaw blade is specified by the number of teeth for centimeter. Hacksaw
blades have a number of teeth ranging from 5 to 15 per centimeter (cm). Blades having lesser
number of teeth per cm are used for cutting soft materials like aluminum, brass and bronze.
Blades having larger number of teeth per centimeter are used for cutting hard materials like steel
and cast Iron. Hacksaw blades are classified as (i) All hard and (ii) flexible type.
The all hard blades are made of H.S.S, hardened and tempered throughout to retain their cutting
edges longer. These are used to cut hard metals. These blades are hard and brittle and can break
easily by twisting and forcing them into the work while sawing. Flexible blades are made of
H.S.S or low alloy steel but only the teeth are hardened and the rest of the blade is soft and
flexible. These are suitable for use by un‐skilled or semi‐skilled persons.

The teeth of the hacksaw blade are staggered, as shown in figure and known as a ‘set of teeth’.
These make slots wider than the blade thickness, preventing the blade from jamming.

Figure 1.13: Hacksaw frame with blade

1.4.2 Chisels

Chisels are used for removing surplus metal or for cutting thin sheets. These tools are made
from 0.9% to 1.0% carbon steel of octagonal or hexagonal section. Chisels are annealed,
hardened and tempered to produce a tough shank and hard cutting edge. Annealing relieves the
internal stresses in a metal. The cutting angle of the chisel for general purpose is about 60°.

Figure 1.15: Flat chisel

1.4.3 Twist Drill

Twist drills are used for making holes. These are made of High speed steel. Both straight and
taper shank twist drills are used. The parallel shank twist drill can be held in an ordinary self –
centring drill check. The tapper shank twist drill fits into a corresponding tapered bore provided
in the drilling machine spindle.
 WORKSHOP PRACTICE (Fitting Shop)

Figure 1.16: Twist drills

1.4.4 Taps and Tap wrenches

A tap is a hardened and steel too l, used for cutting internal thread in a drill hole. Hand Taps are
usually supplied in sets of three in each diameter and thread size. Each set consists of a tapper
tap, intermediate tap and plug or bottoming tap. Taps are made of high carbon steel or high speed
steel.

Figure 1.17: Taps and tap wrench

KFUEIT Page 30
1.4.5 Dies and die‐holders

Dies are the cutting tools used for making external thread. Dies are made either solid or split
type. They are fixed in a die stock for holding and adjusting the die gap. They are made of Steel
or High Carbon Steel.

Figure 1.18: Dies and die holder

1.4.6 Bench Drilling Machine

Holes are drilled for fastening parts with rivets, bolts or for producing internal thread. Bench
drilling machine is the most versatile machine used in a fitting shop for the purpose. Twist drills,
made of tool steel or high speed steel are used with the drilling machine for drilling holes.
Following are the stages in drilling work
1. Select the correct size drills, put it into the check and lock it firmly
2. Adjust the speed of the machine to suit the work by changing the belt on the pulleys. Use high
speed for small drills and soft materials and low speed for large diameter drills and hard
materials.
3. Layout of the location of the pole and mark it with a center punch.
4. Hold the work firmly in the vice on the machine table and clamp it directly on to the machine
table.
5. Put on the power, locate the punch mark and apply slight pressure with the Feed Handle.
6. Once Drilling is commenced at the correct location, apply enough pressure and continue
drilling.
When drilling steel apply cutting oil at the drilling point.
7. Release the pressure slightly, when the drill point pierces the lower surface of the metal. This
prevents the drill catching and damaging the work or drill.
8. On completion of drilling retrace the drill out of the work and put‐off the power supply.
 Figure 1.19: Bench drill

1.5 FINISHING TOOLS

1.5.1 Reamers
Reaming is an operation of sizing and finishing a drilled hole, with the help of a cutting tool
called reamer having a number of cutting edges. For this, a hole is first drilled, the size of which
is slightly smaller than the finished size and then a hand reamer or machine reamer is used for
finishing the hole to the correct size.
Hand Reamer is made of High Carbon Steel and has left‐hand spiral flutes so that, it is prevented
from screwing into the whole during operation. The Shank end of the reamer is made straight so
that it can be held in a tap wrench. It is operated by hand, with a tap wrench fitted on the square
end of the reamer and with the work piece held in the vice. The body of the reamer is given a
slight tapper at its working end, for its easy entry into the whole during operation, it is rotated
only in clock wise direction and also while removing it from the whole.

Figure 1.20: Reamers

1.5.2 Files

Filing is one of the methods of removing small amounts of material from the surface of a metal
part. A file is hardened steel too, having small parallel rows of cutting edges or teeth on its
surfaces.

On the faces, the teeth are usually diagonal to the edge. One end of the file is shaped to fit into a
wooden handle. The figure shows various parts of a hand file. The hand file is parallel in width
and tapering slightly in thickness, towards the tip. It is provided with double cut teeth. On the
faces, single cut on one edge and no teeth on the other edge, which is known as a safe edge.

Figure 1.21: Parts of a hand file

Files are classified according to their shape, cutting teeth and pitch or grade of the teeth. The
figure shows the various types of files based on their shape.

Figure 1.22: Single and double cut files

 WORKSHOP PRACTICE (Fitting Shop)

Figure 1.23: Types of file

1.6 MISCELLANEOUS TOOLS
1.6.1 File card
It is a metal brush, used for cleaning the files, to free them from filings, clogged in‐between the
teeth.

Figure 1.24: File card

KFUEIT Page 34
1.6.2 Ball‐ Peen Hammer
Ball‐ Peen Hammers are named, depending upon their shape and material and specified by their
weight. A ball peen hammer has a flat face which is used for general work and a ball end,
particularly used for riveting.

Figure 1.25: Ball peen hammer

1.6.3 Cross‐Peen Hammer

It is similar to ball peen hammer, except the shape of the peen. This is used for chipping,
riveting, bending and stretching metals and hammering inside the curves and shoulders.
1.6.4 Straight‐Peen Hammer
This is similar to cross peen hammer, but its peen is in‐line with the hammer handle. It is used
for swaging, riveting in restricted places and stretching metals.

Figure 1.26: Cross peen hammer Figure 1.27: Straight peen hammer
1.6.5 Screw driver
A screw driver is designed to turn screws. The blade is made of steel and is available in different
lengths and diameters. The grinding of the tip to the correct shape is very important. A star screw
driver is specially designed to fit the head of star screws. The end of the blade is fluted instead of
flattened. The screw driver is specified by the length of the metal part from handle to the tip.

Figure 1.28: Screw drivers

 WORKSHOP PRACTICE (Fitting Shop)

1.6.7 Spanners
A spanner or wrench is a tool for turning nuts and bolts. It is usually made of forged steel. There
are many kinds of spanners. They are named according to the application. The size of the
spanner denotes the size of the bolt on which it can work.

Figure 1.28: Spanners

KFUEIT Page 36
1.7 SAFE PRACTICE
The following are some of the safe and correct work practices in bench work and fitting shop,
with respect to the tools used
1. Keep hands and tools wiped clean and free of dirt, oil and grease. Dry tools are safer to use
than slippery tools.
2. Do not carry sharp tools on pockets.
3. Wear leather shoes and not sandals.
4. Don’t wear loose clothes.
5. Do no keep working tools at the edge of the table.
6. Position the work piece such that the cut to be made is close to the vice. This practice prevents
springing, saw breakage and personal injury.
7. Apply force only on the forward (cutting) stroke and relieve the force on the return stroke
while sawing and filing.
8. Do not hold the work piece in hand while cutting.
9. Use the file with a properly fitted tight handle.
10. After filing, remove the burrs from the edges of the work, to prevent cuts to the fingers.
11. Do not use vice as an anvil.
12. While sawing, keep the blade straight; otherwise it will break
13. Do not use a file without handle.
14. Clean the vice after use.

PRACTICAL # 1
Square Filing
Aim
To file the given Mild Steel pieces in to a square shape of 48 mm or 2''* 2" side as shown in
Figure.
Tools required
Bench vice, set of Files, Steel rule, Try‐square, Vernier caliper, Vernier height gauge, Ball‐peen
hammer, Scriber, Dot punch

Procedure
1. Required size of square mild steel strip is firstly cut via hacksaw from a long steel strip.
2. The dimensions of the given piece are checked with the steel rule.
3. The job is fixed rigidly in a bench vice and the two adjacent sides are filed, using the rough
flat file first and then the smooth flat file such that, the two sides are at right angle.
4. The right angle of the two adjacent sides is checked with the try‐square.
5. Chalk is then applied on the surface of the work piece.
6. The given dimensions are marked by scribing two lines, with reference to the above two
datum sides by using Vernier height gauge, Angle plate and Surface plate.
7. Using the dot punch, dots are punched along the above scribed lines.
8. The two sides are then filed, by fitting the job in the bench vice; followed by checking the
flatness of the surfaces. As the material removal through filing is relatively less, filing is
done instead of sawing.
Result
The square pieces of 48 mm or 2"*2" side is thus obtained by filing, as discussed above.

a. Raw material b. Finished job

Figure: Square filing

PRACTICAL # 2

Centre Punching, Internal & External Threading

Aim
To centre punch the filed Mild Steel piece, and make internal and external threading as shown in
Figure.

Tools required

Bench vice, set of Files, Steel rule, Try‐square, Vernier caliper, Vernier height gauge, Ball‐peen
hammer, Scriber, Dot punch

Diagram
Procedure

 After square filing with square piece was scribed with a scriber and at the centre a marking
point was made with the help of dot punch and centre punch.

 With the help of drilling machine a hole is made so that the cylindrical rod after external
threading would properly fix into that hole.

 Internal threading was made with the help of taps and tap wrenches and external threading
with the help of dies and die holders.