Scribd
Upload
141 views1 page

SOM - Fieldwork 02

A compound bar consists of four brass wires and one steel wire of different diameters supporting a 500N load. Stresses in each wire are to be determined. The equivalent modulus of the compound bar is also calculated to check the stress values. A compound bar made of aluminum and brass is subjected to a temperature increase and compressive load. Stresses induced in the materials are calculated. Finally, a composite bar made of steel and copper attached by pins experiences a temperature increase and tensile force, with stresses in each material and shear stress in the pins determined.

Uploaded by

Alexander Mugabe
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
141 views1 page

SOM - Fieldwork 02

A compound bar consists of four brass wires and one steel wire of different diameters supporting a 500N load. Stresses in each wire are to be determined. The equivalent modulus of the compound bar is also calculated to check the stress values. A compound bar made of aluminum and brass is subjected to a temperature increase and compressive load. Stresses induced in the materials are calculated. Finally, a composite bar made of steel and copper attached by pins experiences a temperature increase and tensile force, with stresses in each material and shear stress in the pins determined.

Uploaded by

Alexander Mugabe
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

STRENGTH OF MATERIALS

Fieldwork 02
Question 01
a). A compound bar consists of four brass wires of 2.5 mm diameter and one steel wire of 1.5 mm
diameter. Determine the stresses in each of the wires when the bar supports a load of 500 N.
Assume all of the wires are of equal lengths. [10]

(b) Calculate the “equivalent” or “combined modulus for the compound bar and determine its total
extension if it is initially 0.75 m long. Hence check the values of the stresses obtained in part (a).

For brass E = 100 GN/m’ and for steel E = 200 GN/m’. [10]

Question 02

a). A compound bar is constructed from three bars 50 mm wide by 12 mm thick fastened together to
form a bar 50 mm wide by 36 mm thick. The middle bar is of aluminium alloy for which E = 70GN/m2
and the outside bars are of brass with E = 100 GN/m2. If the bars are initially fastened at 18°C and
the temperature of the whole assembly is then raised to 50°C, determine the stresses set up in the
brass and the aluminium. [10]

b). What will be the changes in these stresses if an external compressive load of 35kN is applied to
the compound bar at the higher temperature? [10]

Question 03

A steel rod of cross-sectional area 600 mm2 and a coaxial copper tube of cross-sectional area
1000mm2 are firmly attached at their ends to form a compound bar. Determine the stress in the
steel and in the copper when the temperature of the bar is raised by 80°C and an axial tensile force
of 60 kN is applied.

For steel, E = 200 GN/m2 with = 11 × 10 /ºC

For copper, E = 100 GN/m2 with = 16.5 × 10 /ºC [20]

Question 04

a). A composite bar is constructed from a steel rod of 25 mm diameter surrounded by a copper tube
of 50 mm outside diameter and 25 mm inside diameter. The rod and tube are joined by two 20 mm
diameter pins as shown in Fig. 01. Find the shear stress set up in the pins if, after pinning, the
temperature is raised by 50°C.

For steel E = 210 GN/m2 and = 11 × 10 /ºC

For copper E = 105 GN/m2 and = 17 × 10 /ºC [20]

You might also like