Scribd
Upload
193 views

Nickdj - Co.Uk: Technicolor Tg588V V2 - Manual Configuration

This document provides instructions for manually configuring a Technicolor TG588v v2 router to connect to the internet using either FTTC or ADSL. It recommends factory resetting the router before configuring. For FTTC, the document instructs to enable VDSL, enter the username and password from the ISP, and set the MTU to 1492 and enable VLAN with ID 101. For ADSL, it instructs to enable ADSL, enter the authentication credentials from the ISP, and leave the default settings for MTU, ATM VP, ATM VC, and encapsulation type. The router should then be saved and allowed to connect with the new

Uploaded by

alascarlyb
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
193 views

Nickdj - Co.Uk: Technicolor Tg588V V2 - Manual Configuration

This document provides instructions for manually configuring a Technicolor TG588v v2 router to connect to the internet using either FTTC or ADSL. It recommends factory resetting the router before configuring. For FTTC, the document instructs to enable VDSL, enter the username and password from the ISP, and set the MTU to 1492 and enable VLAN with ID 101. For ADSL, it instructs to enable ADSL, enter the authentication credentials from the ISP, and leave the default settings for MTU, ATM VP, ATM VC, and encapsulation type. The router should then be saved and allowed to connect with the new

Uploaded by

alascarlyb
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Technicolor TG588v v2 – Manual Configuration

.uk
Note: We recommend changes made to this router are performed by a computer using a Windows
operating system and connected via an Ethernet cable. Using a computer with a MAC operating
system or wireless device may cause issues and settings may no save correctly. If the router has been
previously configured using one of these devices it is best to factory reset the router before
continuing with a computer using Windows.

The following guide shows how to manually configure a Technicolor TG588v v2 router to work with
an FTTC or ADSL.

It is recommended the router is first factory reset before following this guide. This can be achieved

.co
by holding a paperclip in the reset hole for 15 seconds, located on the rear of the unit.
DJ

Using a web browser navigate to 192.168.1.1 and click sign in.


ck
Ni
.uk
.co
The default username is admin and default password is admin.
DJ
ck

Once this has been entered you will get the following prompt. It is recommended to use serial
number of the router as the new password.
Ni
.uk
Click Setup your gateway.
.co
Configuring for FTTC
DJ
ck

By default the option for VDSL (FTTC) is selected and Enabled is off. Make sure Enabled is toggled
on.
Ni
.uk
setting.
.co
Enter the username and password provided by your ISP. If configuring for VDSL/FTTC make sure
make sure MTU is set to 1492 and VLAN is enables with the ID of 101. This should be the default

Once complete click Save to finish the process. You may need to wait a few minutes for the router
to connect.
DJ
Configuring for ADSL
ck
Ni

When you select the option ADSL you will get the above screen. Click on Save Connection Type.
.uk
.co
By default the option for ADSL is selected and Enabled is off. Make sure Enabled is toggled on. You
can leave IPV6 off and Routed Type should always be set to PPPoA.
DJ
ck

Enter the ADSL authentication Username and Password provided to you by your ISP.
The default settings for MTU (1500), ATM VP (0), ATM VC (38), and Encapsulation Type (VCMUX)
can be left as they are.
Ni

Click on Save to complete the process.

The TG588v v2 has now been configured. Please allow a few minutes for the router to try and
connect with the new settings.

You might also like