8 7 6 5 4 3 DWG NO.

432-0003-XX-19
SH
1
REV
B 1
NOTES: UNLESS OTHERWISE SPECIFIED
1 CLEARANCE REQUIRED FOR FREE MOTION OF SYSTEM.
2 O-RING USED FOR SEALING SYSTEM TO MOUNTING STRUCTURE.
STANDALONE UNIT MEETS IPX6 SEALING SPECIFICATION. MINIMUM
MOUNTING SURFACE FLATNESS OF 1.5mm [0.60in] OVER SYSTEM
DIAMETER REQUIRED FOR O-RING USE. WHEN MOUNTING TO
IRREGULAR SURFACES, USE OF BEDDING COMPOUND RECOMMENDED.
D 3 USE WITH FLIR MOUNTING HARDWARE KITS: D
4115301 HARDWARE KIT - M-SERIES BASIC MOUNT
500-0399-00 TOP DOWN RISER INSTALLATION KIT
4. USE LOCTITE 242 WITH ALL METAL TO METAL THREADED
CONNECTIONS.
5 WARNING
DO NOT BOTTOM FASTENERS IN BASE. M-SERIES
BOLT LENGTH NOT TO EXCEED 6mm INTO BASE
ELECTRONICS WILL BE DAMAGED BY BASE PENETRATION - VOIDING WARRANTY. DUAL PAYLOAD 7.3 1
BOLT TORQUE NOT TO EXCEED 9.5 N-m [7 LB-f]. 184.4

IR CAMERA

11.6 1
294.9
C C

9.2 VISIBLE CAMERA

233.8
7.3
185.8

DWG NO.
7.0 2
178.8
AS568A-427 EP O-RING

432-0003-XX-19
[4.75in ID x 0.25in DIA. EP]
120mm ID x 7mm DIA. EP
AS568A-334 EP O-RING
3.9 [2.63in ID x 0.19in DIA. EP]
100.0 BOLT CIRCLE 67mm ID x 5mm DIA. EP
B
5.7
145.0 MIN BASE PLATE DIAMETER

SH
FOR EFFECTIVE O-RING SEAL. CABLES SHOWN FOR REFERENCE ONLY.

1
6x M6x1.0 6 HELICOILS 3 NOT TO SCALE, NOR CORRECT LENGTH.

REV
381 25mm [15 1in] POWER CABLE, UNTERMINATED TINNED 18AWG WIRE.

B
WARNING 5 457 25mm [18 1in] NETWORK CABLE, RJ45 T568B, MALE.
533 25mm [21 1in] IR VIDEO CABLE, F-TYPE MALE.
584 25mm [23 1in] SWITCHED (IR OR VIS) VIDEO CABLE, F-TYPE MALE.

1.6
41.0 MIN CABLE PORT
IMPORTANT: 63.5 MAX
CHASSIS GROUND SHALL BE TIED
TO ONE MOUNTING FASTENER THIRD ANGLE PROJECTION PROPRIETARY - FLIR SYSTEMS, INC.
FOR HIGH CONDUCTIVE PATH
TO VESSEL GROUND. MAX 0.25Ω.
THIS DOCUMENTATION CONTAINS PROPRIETARY INFORMATION TO FLIR SYSTEMS, INC. THIS INFORMATION
MUST BE MAINTAINED IN CONFIDENCE AND USED ONLY IN A MANNER CONSISTENT WITH THE DOCUMENTATION
AND ANY EXECUTED NON DISCLOSURE AGREEMENT, AND MAY NOT BE DISCLOSED TO ANY THIRD PARTIES
WITHOUT FLIR'S WRITTEN CONSENT.
A WARRANTY VOID IF SCREWS REMOVED.
METRIC A
MATERIAL PROJECT NO. FLIR Systems, Inc.
INTERPRET DRAWING 6769 Hollister Drive
N/A APPROVALS DATE Goleta, CA 93117
PER ASME Y14.5M-1994
---------------------------------------------- FINISH DWN M. COSLEY 05/09/2017 TITLE
UNLESS OTHERWISE SPECIFIED N/A CHK
M-SERIES ICD, SINGLE / DUAL PAYLOAD
SURFACE ROUGHNESS 0.8um
.X = .25 UNLESS OTHERWISE SPECIFIED ALL DSGN M. COSLEY 05/09/2017
SIZE CAGE DWG NO. REV
.XX = .13 064Y2 432-0003-XX-19 B
MEASUREMENTS ARE IN MM.

ANGULAR = .5
ALL DIMENSIONS IN [ ] ARE INCHES.
DO NOT SCALE DRAWING.
ENG
D
FILLET RADII = .13 MAX CALC WT: 6362.667 GRAMS
APP
SCALE 1:5 PRINTED: 5/25/2017 SHEET 1 OF 11

8 7 6 5 4 3 2 1
SOLIDWORKS MODEL: 432-0003-XX-YY Pelagic M-Series ICD, Single and Dual Payload
MODEL REVISION: B
 8 7 6 5 4 3 DWG NO.
432-0003-XX-19
SH
2
REV
B 1
NOTES: UNLESS OTHERWISE SPECIFIED
1 CLEARANCE REQUIRED FOR FREE MOTION OF SYSTEM.
2 O-RING USED FOR SEALING SYSTEM TO MOUNTING STRUCTURE.
STANDALONE UNIT MEETS IPX6 SEALING SPECIFICATION. MINIMUM
MOUNTING SURFACE FLATNESS OF 1.5mm [0.60in] OVER SYSTEM
DIAMETER REQUIRED FOR O-RING USE. WHEN MOUNTING TO
IRREGULAR SURFACES, USE OF BEDDING COMPOUND RECOMMENDED.
D 3 USE WITH FLIR MOUNTING HARDWARE KITS: D
4115301 HARDWARE KIT - M-SERIES BASIC MOUNT
500-0399-00 TOP DOWN RISER INSTALLATION KIT
4. USE LOCTITE 242 WITH ALL METAL TO METAL THREADED
CONNECTIONS.
1
5 WARNING
DO NOT BOTTOM FASTENERS IN BASE. M-SERIES 6.6
BOLT LENGTH NOT TO EXCEED 6mm INTO BASE
ELECTRONICS WILL BE DAMAGED BY BASE PENETRATION - VOIDING WARRANTY. SINGLE PAYLOAD IR CAMERA
168.0
BOLT TORQUE NOT TO EXCEED 9.5 N-m [7 LB-f].

C 11.3
C
1
286.8

8.0
202.8

DWG NO.
AS568A-427 EP O-RING
[4.75in ID x 0.25in DIA. EP]
120mm ID x 7mm DIA. EP

432-0003-XX-19
AS568A-334 EP O-RING
7.0 [2.63in ID x 0.19in DIA. EP]
178.8 67mm ID x 5mm DIA. EP
B
3.9
100.0 BOLT CIRCLE CABLES SHOWN FOR REFERENCE ONLY.

SH
5.7 NOT TO SCALE, NOR CORRECT LENGTH.
145.0 MIN BASE DIAMETER

2
6x M6x1.0 6 HELICOILS 3 381 25mm [15 1in] POWER CABLE, UNTERMINATED TINNED 18AWG WIRE.
FOR EFFECTIVE SEAL

REV
457 25mm [18 1in] NETWORK CABLE, RJ45 T568B, MALE.
533 25mm [21 1in] IR VIDEO CABLE, F-TYPE MALE.

B
WARNING 5 584 25mm [23 1in] SWITCHED (IR OR VIS) VIDEO CABLE, F-TYPE MALE.

1.6
40.0 MIN CABLE PORT
63.5 MAX
IMPORTANT:
CHASSIS GROUND SHALL BE TIED
TO ONE MOUNTING FASTENER
FOR HIGH CONDUCTIVE PATH
A TO VESSEL GROUND. MAX 0.25Ω. WARRANTY VOID IF SCREWS REMOVED. A
M-SERIES ICD, SINGLE / DUAL PAYLOAD
METRIC
PROPRIETARY - FLIR SYSTEMS, INC.

432-0003-XX-19
SIZE CAGE PIECE PART. REV
FLIR Systems, Inc.
70 Castilian Drive D 064Y2 B
Goleta, CA 93117
SCALE 1:33.3 PRINTED: 5/25/2017 SHEET 2 OF 11

8 7 6 5 4 3 2 1
SOLIDWORKS MODEL: 432-0003-XX-YY Pelagic M-Series ICD, Single and Dual Payload
MODEL REVISON: B
 4 3 DWG NO.
432-0003-XX-19 SH
3 REV A 1
IMPORTANT NOTE:
PAPER SIZE: 11x17in
D TEMPLATE SHOULD PRINT 1:1 D
DUE TO VARIATION IN SOFTWARE AND
0.3 PRINTERS, PLEASE VERIFFY SCALE BELOW
6x 6.4 THRU HOLE BEFORE MODIFYING MOUNTING SURFACE.
EQUALLY SPACED ON
100 [3.94] BOLT CIRCLE

2.00IN
C C

50.0MM

40.0 [1.57] MIN CABLE PORT.

63.5 [2.50] MAX

B B

7.1
179.4 M-SERIES O.D.

A A
MOUNTING TEMPLATE
M-SERIES GIMBAL
064Y2
SIZE CAGE DWG NO. REV
B 432-0003-XX-19 A
PROPRIETARY - FLIR SYSTEMS, INC. SCALE 1:1 PRINTED: 5/25/2017 SHEET 3 OF 11

4 3 2 1
 8 7 6 5 4 3 DWG NO.
432-0003-XX-19
SH
4
REV
B 1

1.3 3.0
32.1 77.3
D D

3.6
90.4

5.6
141.4

C C

WITH CABLE INSTALLED, TURN NUT

1/4 TURN BEYOND HAND TIGHT.

GLAND SEAL DESIGNED FOR USE WITH DOUBLE SHIELDED

DWG NO.
CAT 5 ETHERNET CABLE. USE OF SINGLE SHIELDED CABLE
IP66 RATED IN FRONT OF GASKET. IP64 RATED BEHIND GASKET. MAY REQUIRE THE USE OF ADDITIONAL SEALANT SUCH
AS SILICON OR RTV TO ENSURE SEALING OF ENCLOSURE.

432-0003-XX-19
INSERT NETWORK CABLE RJ45 THROUGH GLAND NUT AND
SEAL BEFORE INSTALLING.

SH
APPLY ADHESIVE SIDE OF GASKET TO JCU BODY.

4
B REV
2.4
60.9
MOUNTING PANEL THICKNESS RANGE 1.6-45 [0.063-1.750].
WHEN MOUNTING TO PANELS LESS THAN 6.3 [0.25] REVERSE
PADDLES AS ILLUSTRATED.

A A
DURING INITIAL TIGHTENING, ENSURE MOUNTING TABS
ON SCREWS SWING FREE OF REAR HOUSING. WITH TABS JOYSTICK CONTROL UNIT - MARITIME, MULTI
RUN UP AGAINST REAR OF INSTRUMENT PANEL, TIGHTEN
1/4-1/2 TURN BEYOND HAND TIGHT.
METRIC
PROPRIETARY - FLIR SYSTEMS, INC.

432-0003-XX-19
SIZE CAGE PIECE PART. REV
FLIR Systems, Inc.
70 Castilian Drive D 064Y2 B
Goleta, CA 93117
SCALE 1:1 PRINTED: 5/25/2017 SHEET 4 OF 11

8 7 6 5 4 3 2 1
SOLIDWORKS MODEL: 432-0003-XX-YY Pelagic M-Series ICD, Single and Dual Payload
MODEL REVISON: B
 4 3 DWG NO.
432-0003-XX-19 SH
5 REV A 1
IMPORTANT NOTE:
2.8 PAPER SIZE: 11x17in
D CORNERS SHALL 72.3 TEMPLATE SHOULD PRINT 1:1 D
BE SHARP. OPTIONAL
DRILL GUIDE DUE TO VARIATION IN SOFTWARE AND
PRINTERS, PLEASE VERIFFY SCALE BELOW
BEFORE MODIFYING MOUNTING SURFACE.
FITS JCU P.N. 500-0385-00

C C

4.8 5.1±0.05 5.6

123.1 141.4 2.00IN
129.54±1.25
OPTIONAL CUTOUT OUTSIDE
DRILL GUIDE OF JCU

0.25 50.0MM
6.4
B B

3.1±0.05
78.74±1.25
CUTOUT

3.6
A A
90.4
OUTSIDE
OF JCU M-SERIES ICD, SINGLE / DUAL PAYLOAD
064Y2
SIZE CAGE DWG NO. REV
B 432-0003-XX-19 A
PROPRIETARY - FLIR SYSTEMS, INC. SCALE 1:1 PRINTED: 5/25/2017 SHEET 5 OF 11

4 3 2 1
 8 7 6 5 4 3 DWG NO.
432-0003-XX-19
SH
6
REV
B 1

D D

M-SERIES
SINGLE / DUAL PAYLOAD

JCU

C C

POWER CABLE
18AWG TINNED STRANDED WIRE
RED WIRE: +12-24 VDC (3.8-1.9 AMP MAX)
BLK WIRE: DC RETURN ATTACH GROUND STRAP
GRN WIRE: EARTH GROUND TO MOUNTING STUD
NETWORK CABLE FOR PoE DEVICES (IEEE802.3af) 8
CONDUCTOR T568B, ETHERNET, DOUBLE SHIELDED
CONNECTOR FLIR PN 308-0163-25 OR EQUIVALENT
BUTT SPLICE OR INSTALLER RJ45 WATERPROOF ENCLOSURE NOTE: TO MAINTAIN IEC 60945 EMI COMPLIANCE
SUPPLIED CONNECTOR FLIR PN 4115028 USE OF DOUBLE SHIELDED CABLE REQUIRED

DWG NO.
4X FERRITE CABLE SNAP
TO BE PLACED AS CLOSE
TO BASE AS POSSIBLE

432-0003-XX-19
FLIR PN 4211315
RG59U VIDEO CABLE
F-TYPE MALE TERMINATION
B DISPLAY

6 SH
SWITCHED (IR OR VIS) VIDEO CABLE

REV
(DUAL ONLY)

B
INSTALLER SUPPLIED POWER CABLE
GAUGE OF WIRE TO BE APPROPRIATE
FOR SUPPLY VOLTAGE AND LENGTH OF
CABLE RUN TO ENSURE ADEQUATE
CURRENT CARRYING CAPABILITY. CONNECTOR IR VIDEO CABLE
F-TYPE FEMALE TO FEMALE
FLIR PN 4115330

RG59U VIDEO CABLE

F-TYPE MALE TO BNC MALE
FLIR PN 308-0164-25
A A
INTERCONNECT DIAGRAM
SINGLE JCU
METRIC
PROPRIETARY - FLIR SYSTEMS, INC.

432-0003-XX-19
SIZE CAGE PIECE PART. REV
FLIR Systems, Inc.
70 Castilian Drive D 064Y2 B
Goleta, CA 93117
SCALE 1:2 PRINTED: 5/25/2017 SHEET 6 OF 11

8 7 6 5 4 3 2 1
SOLIDWORKS MODEL: 432-0003-XX-YY Pelagic M-Series ICD, Single and Dual Payload
MODEL REVISON: B
 8 7 6 5 4 3 DWG NO.
432-0003-XX-19
SH
7
REV
B 1

M-SERIES
SINGLE / DUAL PAYLOAD
D D
JCU 1 JCU 2
FLIR PN 500-0385-00

MANUFACTURER SPECIFIC ENVIRONMENTAL

EXPOSURE RATINGS APPLY

POWER CABLE
18AWG TINNED STRANDED WIRE
RED WIRE: +12-24 VDC (3.8-1.9 AMP MAX)
BLK WIRE: DC RETURN ATTACH GROUND STRAP
GRN WIRE: EARTH GROUND TO MOUNTING STUD
POE NETWORK SWITCH
IEEE802.3af, T568B COMPLIANT
FLIR PN 4141042
CONNECTOR RJ45
C BUTT SPLICE OR INSTALLER WATERPROOF
ENCLOSURE
C
SUPPLIED CONNECTOR
FLIR PN 4115028

4X FERRITE CABLE SNAP

TO BE PLACED AS CLOSE
TO BASE AS POSSIBLE
FLIR PN 4211315
RG59U VIDEO CABLE NETWORK CABLE FOR PoE DEVICES (IEEE802.3af)
F-TYPE MALE TERMINATION 8 CONDUCTOR T568B, ETHERNET, DOUBLE SHIELDED
FLIR PN 308-0163-25 OR EQUIVALENT
NOTE: TO MAINTAIN IEC 60945 EMI COMPLIANCE,
USE OF DOUBLE SHIELDED CABLE REQUIRED.

DWG NO.
INSTALLER SUPPLIED POWER CABLE

432-0003-XX-19
GAUGE OF WIRE TO BE APPROPRIATE FOR
SUPPLY VOLTAGE AND LENGTH OF CABLE
RUN TO ENSURE ADEQUATE CURRENT DISPLAY
CARRYING CAPABILITY.
B SWITCHED (IR OR VIS)
VIDEO CABLE
(DUAL ONLY)

7 SH
REV
CONNECTOR
F-TYPE FEMALE TO FEMALE

B
FLIR PN 4115330

IR VIDEO CABLE

RG59U VIDEO CABLE

F-TYPE MALE TO BNC MALE
FLIR PN 308-0164-25

A A
INTERCONNECT DIAGRAM
MULTIPLE JCU - POE SWITCH
METRIC
PROPRIETARY - FLIR SYSTEMS, INC.

432-0003-XX-19
SIZE CAGE PIECE PART. REV
FLIR Systems, Inc.
6769 Hollister Ave. D 064Y2 B
Goleta, CA 93117
SCALE 1:2 PRINTED: 5/25/2017 SHEET 7 OF 11

8 7 6 5 4 3 2 1
SOLIDWORKS MODEL: 432-0003-XX-YY Pelagic M-Series ICD, Single and Dual Payload
MODEL REVISON: B
 8 7 6 5 4 3 DWG NO.
432-0003-XX-19
SH
8
REV
B 1

D D

M-SERIES
SINGLE / DUAL PAYLOAD

JCU 1 JCU 2

MANUFACTURER SPECIFIC ENVIRONMENTAL

EXPOSURE RATINGS APPLY
ATTACH GROUND STRAP
TO MOUNTING STUD
C POWER CABLE
18AWG TINNED STRANDED WIRE C
RED WIRE: +12-24 VDC (3.8-1.9 AMP MAX)
BLK WIRE: DC RETURN
GRN WIRE: EARTH GROUND CONNECTOR
RJ45 WATERPROOF NETWORK SWITCH, NON PoE
ENCLOSURE INSTALLER SUPPLIED
FLIR PN 4115028
BUTT SPLICE OR INSTALLER
SUPPLIED CONNECTOR

4X FERRITE CABLE SNAP

TO BE PLACED AS CLOSE POE INJECTOR
TO BASE AS POSSIBLE IP20, RJ45 FEMALE NETWORK CABLE FOR PoE DEVICES (IEEE802.3af)
FLIR PN 4211315 FLIR PN 4113746 8 CONDUCTOR T568B, ETHERNET, DOUBLE SHIELDED

DWG NO.
RG59U VIDEO CABLE FLIR PN 308-0163-25 OR EQUIVALENT
F-TYPE MALE TERMINATION NOTE: TO MAINTAIN IEC 60945 EMI COMPLIANCE,
USE OF DOUBLE SHIELDED CABLE REQUIRED.

432-0003-XX-19
B
INSTALLER SUPPLIED POWER CABLE POE INJECTOR POWER REQUIREMENT
+9-36VDC (12V/1.85A - 24V/0.90A)
GAUGE OF WIRE TO BE APPROPRIATE

SH
FOR SUPPLY VOLTAGE AND LENGTH
OF CABLE RUN TO ENSURE ADEQUATE

8
CURRENT CARRYING CAPABILITY.

REV
DISPLAY

B
SWITCHED (IR OR VIS)
VIDEO CABLE
(DUAL ONLY)

CONNECTOR
F-TYPE FEMALE TO FEMALE
FLIR PN 4115330

IR VIDEO CABLE
RG59U VIDEO CABLE
F-TYPE MALE TO BNC MALE
FLIR PN 308-0164-25

A A
INTERCONNECT DIAGRAM
MULTIPLE JCU - POE INJECTOR
METRIC
PROPRIETARY - FLIR SYSTEMS, INC.

432-0003-XX-19
SIZE CAGE PIECE PART. REV
FLIR Systems, Inc.
6769 Hollister Ave. D 064Y2 B
Goleta, CA 93117
SCALE 1:2 PRINTED: 5/25/2017 SHEET 8 OF 11

8 7 6 5 4 3 2 1
SOLIDWORKS MODEL: 432-0003-XX-YY Pelagic M-Series ICD, Single and Dual Payload
MODEL REVISON: B
 8 7 6 5 4 3 DWG NO.
432-0003-XX-19
SH
9
REV
B 1

GIMBAL ASSEMBLY CUSTOMER SEAL, OPTIONAL PER APPLICATION

WEIGHT: < 5.0 kg [11 lb] SOC HD CAP SCREW
M6 x 1.0
LENGTH: 6mm + THICKNESS OF CUSTOMER DECKING
316 STAINLESS STEEL
D 6 PLACES
APPLY THREAD LOCKER (LOCTITE 242 OR EQUIVALENT)
D
TORQUE TO 9.5 N-m [7 LB-f]
WARNING 5
IMPORANT:
CHASIS GROUND SHALL BE TIED TO
ONE MOUNTING FASTENER FOR HIGH
CONDUCTIVITY PATH TO VESSEL GROUND.
MAX 0.25Ω
WASHER, OPTIONAL
M6
316 STAINLESS STEEL

CUSTOMER STRUCTURE, SEALED ENCLOSURE, DRY SPACE

SHOWN SECTIONED AND BROKEN AWAY

C NOTE HOME POSITION ORIENTATION C

ON BOTTOM OF SYSTEM BASE
AS568A-427 EP O-RING
[4.75in ID x 0.25in DIA. EP]
120mm ID x 7mm DIA.EP
FITS IN LARGER DIAMETER GLAND OF GIMBAL ASSY

CUSTOMER DECKING, OR OTHER STRUCTURE

AS568A-427 EP O-RING

DWG NO.
[4.75in ID x 0.25in DIA. EP] HOLES, MOUNTING
120mm ID x 7mm DIA.EP 6.4mm DIAMETER
FITS IN LARGER DIAMETER GLAND OF GIMBAL ASSY 6 PLACES

432-0003-XX-19
HOLES, MOUNTING
6.4mm DIAMETER HOLE CABLE PASS
6 PLACES 40.0mm DIAMETER MIN.
NOTE HOME POSITION ORIENTATION 63.5mm DIAMETER MAX
ON BOTTOM OF SYSTEM BASE
B

9 SH
IMPORANT:

REV
CHASIS GROUND SHALL BE TIED TO
ONE MOUNTING FASTENER FOR HIGH

B
CONDUCTIVITY PATH TO VESSEL GROUND.
MAX 0.25Ω HOLE CABLE PASS
40.0mm DIAMETER MIN.
63.5mm DIAMETER MAX
WASHER, OPTIONAL
M6
316 STAINLESS STEEL

SOC HD CAP SCREW

M6 x 1.0
LENGTH: 6mm + THICKNESS OF CUSTOMER DECKING
316 STAINLESS STEEL
6 PLACES GIMBAL ASSEMBLY
APPLY THREAD LOCKER (LOCTITE 242 OR EQUIVALENT) HIDDEN CABLING MOUNTING SCHEME: WEIGHT: < 5.0 kg [11 lb]
TORQUE TO 9.5 N-m [7 LB-f]
A A
WARNING 5 MOUNTING DIRECTLY THROUGH CUSTOMER DECKING, OR OTHER SURFACES
HIDDEN CABLING MOUNTING SCHEME: STRUCTURE OPPOSITE GIMBAL TO BE SEALED ENCLOSURE AND A DRY SPACE
CAMERA BALL UP CONFIGURATION
MOUNTING DIRECTLY THROUGH CUSTOMER DECKING, OR OTHER SURFACES
STRUCTURE OPPOSITE GIMBAL TO BE SEALED ENCLOSURE AND A DRY SPACE ENTIRE ASSEMBLY CAN BE ROTATED 180 FOR BALL UP INSTALLATION METRIC
CAMERA BALL UP CONFIGURATION PROPRIETARY - FLIR SYSTEMS, INC.
HOME DIRECTION ZERO CAN BE SET FROM MENU.
ENTIRE ASSEMBLY CAN BE ROTATED 180 FOR BALL DOWN INSTALLATION
432-0003-XX-19
SIZE CAGE PIECE PART. REV
FLIR Systems, Inc.
D 064Y2 B
SCALE 1/2 6769 Hollister Ave.
HOME DIRECTION ZERO CAN BE SET FROM MENU. Goleta, CA 93117
SCALE 1:5 PRINTED: 5/25/2017 SHEET 9 OF 11

8 7 6 5 4 3 2 1
SOLIDWORKS MODEL: 432-0003-XX-YY Pelagic M-Series ICD, Single and Dual Payload
MODEL REVISON: B
 8 7 6 5 4 3 DWG NO.
432-0003-XX-19
SH
10
REV
B 1

D D

CONDUIT AND FITTINGS

NUT, HEX (NYLOCK AND ACORN NUTS, OPTIONAL) CUSTOMER SUPPLIED
M6 X 1.0 PARTS SHOWN EXAMPLE ONLY
316 STAINLESS STEEL
WASHER, OPTIONAL 6 PLACES
M6 APPLY THREAD LOCKER (LOCTITE 242 OR EQUIVALENT) NUT, HEX (NYLOCK AND ACORN NUTS, OPTIONAL)
316 STAINLESS STEEL M6 X 1.0
6 PLACES 316 STAINLESS STEEL
IMPORTANT:
CHASSIS GROUND SHALL BE TIED TO ONE MOUNTING FASTENER 6 PLACES
FOR HIGH CONDUCTIVE PATH TO VESSEL GROUND. APPLY THREAD LOCKER (LOCTITE 242 OR EQUIVALENT)
MAX 0.25Ω
WASHER, OPTIONAL IMPORTANT:
HOLES, MOUNTING M6 CHASSIS GROUND SHALL BE TIED TO ONE
6.4mm DIAMETER 316 STAINLESS STEEL MOUNTING FASTENER FOR HIGH
6 PLACES 6 PLACES CONDUCTIVE PATH TO VESSEL GROUND.
MAX 0.25Ω

HOLE CABLE PASS

40.0mm DIAMETER MIN. CONDUIT HUB
50.4mm DIAMETER MAX.
(FOR O-RING SEAL)
C C

HOLE CABLE PASS

40.0mm DIAMETER MIN.
63.5mm DIAMETER MAX. MOUNT, CAMERA
CUSTOMER SUPPLIED
UNIT SHOWN EXAMPLE ONLY

HOLES, MOUNTING
NOTE HOME POSITION ORIENTATION 6.4mm DIAMETER
ON BOTTOM OF SYSTEM BASE 6 PLACES
SPACER, THRU
6.4 ID X 17.3 OD X 3.2 THICK MOUNT, CAMERA
316 STAINLESS STEEL NOTE HOME POSITION ORIENTATION CUSTOMER SUPPLIED
6 PLACES ON BOTTOM OF SYSTEM BASE UNIT SHOWN EXAMPLE ONLY

DWG NO.
STUD, MALE
M6 X 1.0 (LENGTH 19mm + THICKNESS OF MOUNT)
316 STAINLESS STEEL
6 PLACES

432-0003-XX-19
[APPLY THREAD LOCKER (LOCTITE 242 OR EQUIVALENT)
STUD, MALE
WARNING 5 M6 X 1.0 (LENGTH 19mm + THICKNESS OF MOUNT)
316 STAINLESS STEEL
B 6 PLACES
[APPLY THREAD LOCKER (LOCTITE 242 OR EQUIVALENT)
WARNING 5

10
B SH
REV
GIMBAL ASSEMBLY
WEIGHT: <5 kg [11 lb] GIMBAL ASSEMBLY
WEIGHT: <5 kg [11 lb]

A EXPOSED CABLING MOUNTING SCHEME: A

EXPOSED CABLING MOUNTING SCHEME: CUSTOMER PROVIDED MOUNTING BRACKET / SURFACE
CAMERA BALL DOWN CONFIGURATION
CUSTOMER PROVIDED OUNTING BRACKET / SURFACE ENTIRE ASSEMBLY CAN BE ROTATED 180 FOR BALL UP INSTALLATION METRIC
CAMERA BALL DOWN CONFIGURATION
PROPRIETARY - FLIR SYSTEMS, INC.
HOME DIRECTION ZERO CAN BE SET FROM MENU.
ENTIRE ASSEMBLY CAN BE ROTATED 180 FOR BALL UP INSTALLATION
432-0003-XX-19
SIZE CAGE PIECE PART. REV
FLIR Systems, Inc.
6769 Hollister Ave. D 064Y2 B
HOME DIRECTION ZERO CAN BE SET FROM MENU. Goleta, CA 93117
SCALE 1:2 PRINTED: 5/25/2017 SHEET 10 OF 11

8 7 6 5 4 3 2 1
SOLIDWORKS MODEL: 432-0003-XX-YY Pelagic M-Series ICD, Single and Dual Payload
MODEL REVISON: B
 8 7 6 5 4 3 DWG NO.
432-0003-XX-19
SH
11
REV
B 1

CHASSIS GROUND SHALL BE TIED TO

MOUNTING FASTENER FOR HIGH CONDUCTIVE
PATH TO VESSEL GROUND. MAX 0.25Ω
(CUSTOMER SUPPLIED)
GIMBAL ASSEMBLY
WEIGHT: <5.0 kg [11 lb]
D D

GROUNDING SCHEME

AS568A-427 EP O-RING
[4.75in ID x 0.25in DIA. EP]
120mm ID x 7mm DIA. EP
FITS IN LARGER DIAMETER GLAND OF GIMBAL ASSY

C C

M6 SCREWS, FLAT HEAD SOC CAP OR,

1/4"-20 SCREWS, FLAT HEAD SOC CAP OR,
#14 X 1.5 SCREWS, FLAT HEAD PHILLIPS SHEET METAL
TYPE AND LENGTH DEPENDANT ON MOUNTING SURFACE
316 STAINLESS STEEL
6 PLACES
NOTE HOME POSITION ORIENTATION APPL THREAD LOCKER (LOCTITE 242 OR EQUIVALENT)
ON BOTTOM OF SYSTEM BASE

TOP DOWN BASE

FLIR PN 500-0399-00 TOP DOWN RISER
INSTALLATION KIT

DWG NO.
CHASSIS GROUND

432-0003-XX-19
SOC HD CAP SCREW
M6 X 1.0 X 10 mm LONG
316 STAINLESS STEEL
6 PLACES
APPLY THREAD LOCKER [LOCTITE 242 OR EQUIVALENT]
B TORQUE TO 9.5 N-m [7 LB-f]
WARNING 5

SH
CUSTOMER DECKING, OR OTHER STRUCTURE

11
HOLE CABLE PASS
40.0 mm DIAMETER MIN.

REV
63.5 mm DIAMETER MAX.

B
HIDDEN CABLING MOUNTING SCHEME

FLIR PROVIDED MOUNTING BRACKET(S)

CAMERA BALL UP CONFIGURATION
A ENTIRE ASSEMBLY VIEW CAN BE ROTATED 180 FOR BALL DOWN INSTALLATION A
HOME DIRECTION ZERO CAN BE SET FROM MENU.
SCALE 1/2
METRIC
PROPRIETARY - FLIR SYSTEMS, INC.

432-0003-XX-19
SIZE CAGE PIECE PART. REV
FLIR Systems, Inc.
6769 Hollister Ave. D 064Y2 B
Goleta, CA 93117
SCALE 1:2 PRINTED: 5/25/2017 SHEET 11 OF 11

8 7 6 5 4 3 2 1
SOLIDWORKS MODEL: 432-0003-XX-YY Pelagic M-Series ICD, Single and Dual Payload
MODEL REVISON: B