BRAKES

BR
A

B
SECTION
BRAKE SYSTEM C

E
CONTENTS
SERVICE INFORMATION ............................ 2 VACUUM LINES ............................................... 21 BR
Component ..............................................................21
PRECAUTIONS ................................................... 2 Removal and Installation .........................................21
Precaution for Supplemental Restraint System Inspection ................................................................21 G
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ................................................................... 2 FRONT DISC BRAKE ....................................... 23
Precaution Necessary for Steering Wheel Rota- On Board Inspection ................................................23
Component ..............................................................23 H
tion After Battery Disconnect ..................................... 2
Precaution for Brake System .................................... 3 Removal and Installation of Brake Pad ...................24
Removal and Installation of Brake Caliper Assem-
PREPARATION ................................................... 4 bly ............................................................................26 I
Special Service Tool ................................................. 4 Disassembly and Assembly of Brake Caliper As-
Commercial Service Tool .......................................... 4 sembly .....................................................................28
Brake Burnishing .....................................................31 J
NOISE, VIBRATION AND HARSHNESS
(NVH) TROUBLESHOOTING ............................. 6 REAR DISC BRAKE ......................................... 32
NVH Troubleshooting Chart ...................................... 6 On Board Inspection ................................................32
Component ..............................................................32 K
BRAKE PEDAL ................................................... 7 Removal and Installation of Brake Pad ...................33
Inspection and Adjustment ........................................ 7 Removal and Installation of Caliper Assembly ........34
Removal and Installation ........................................... 8 Disassembly and Assembly of Caliper Assembly....36 L
BRAKE FLUID ....................................................10 Brake Burnishing .....................................................39
On Board Inspection ............................................... 10 REAR DRUM BRAKE ....................................... 40
Drain and Refill ........................................................ 10 Component ..............................................................40 M
Bleeding Brake System ........................................... 11 Removal and Installation of Drum Brake Assembly
BRAKE TUBE AND HOSE ................................12 ....40
Removal and Installation of Wheel Cylinder ............43 N
Hydraulic Circuit ...................................................... 12
Disassembly and Assembly of Wheel Cylinder .......43
Front Brake Tube and Hose .................................... 13
Rear Brake Tube and Hose .................................... 14 SERVICE DATA AND SPECIFICATIONS
Inspection After Installation ..................................... 16 O
(SDS) ................................................................. 45
BRAKE MASTER CYLINDER ............................17 General Specification ..............................................45
On-Board Inspection ............................................... 17 Brake Pedal .............................................................46
Check Valve ............................................................46 P
Removal and Installation ......................................... 17
Brake Booster ..........................................................47
BRAKE BOOSTER ............................................19 Front Disc Brake ......................................................47
On Board Inspection ............................................... 19 Rear Disc Brake ......................................................47
Removal and Installation ......................................... 19 Rear Drum Brake .....................................................48

Revision: July 2010 BR-1 2011 Sentra

 PRECAUTIONS
< SERVICE INFORMATION >
SERVICE INFORMATION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER" INFOID:0000000006152267

The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SRS section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution Necessary for Steering Wheel Rotation After Battery Disconnect
INFOID:0000000006152268

NOTE:
• This Procedure is applied only to models with Intelligent Key system and NATS (NISSAN ANTI-THEFT SYS-
TEM).
• Remove and install all control units after disconnecting both battery cables with the ignition knob in the
″LOCK″ position.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If DTC is detected, perform trouble diagnosis according to self-diagnostic results.
For models equipped with the Intelligent Key system and NATS, an electrically controlled steering lock mech-
anism is adopted on the key cylinder.
For this reason, if the battery is disconnected or if the battery is discharged, the steering wheel will lock and
steering wheel rotation will become impossible.
If steering wheel rotation is required when battery power is interrupted, follow the procedure below before
starting the repair operation.
OPERATION PROCEDURE
1. Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2. Use the Intelligent Key or mechanical key to turn the ignition switch to the ″ACC″ position. At this time, the
steering lock will be released.
3. Disconnect both battery cables. The steering lock will remain released and the steering wheel can be
rotated.
4. Perform the necessary repair operation.

Revision: July 2010 BR-2 2011 Sentra

 PRECAUTIONS
< SERVICE INFORMATION >
5. When the repair work is completed, return the ignition switch to the ″LOCK″ position before connecting
the battery cables. (At this time, the steering lock mechanism will engage.) A
6. Perform a self-diagnosis check of all control units using CONSULT-III.
Precaution for Brake System INFOID:0000000006152269
B
• Refill using recommended brake fluid. Refer to MA-15.
• Never reuse drained brake fluid.
• Be careful not to splash brake fluid on painted surface of body. If brake fluid is splashed on painted surfaces C
of body immediately wipe it off with cloth and then wash it away with water.
• To clean or wash all parts of master cylinder, disc brake caliper and wheel cylinder, use new brake fluid.
• Never use mineral oils such as gasoline or kerosene. They will ruin rubber parts of the hydraulic system.
D
• Use a flare nut wrench when removing a brake tube and use a
flare nut torque wrench when installing a brake tube.
• When installing brake tubes and hoses, be sure to check torque.
• Before working, turn ignition switch OFF and disconnect connec- E
tors of ABS actuator and electric unit (control unit) or the battery
cable from the negative terminal.
• Burnish the new braking surfaces after refinishing or replacing BR
drums or rotors, after replacing pads or linings, or if a soft pedal
occurs at very low mileage. Refer to BR-31, "Brake Burnishing".

G
SBR686C

Revision: July 2010 BR-3 2011 Sentra

 PREPARATION
< SERVICE INFORMATION >
PREPARATION
Special Service Tool INFOID:0000000006152270

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number Description
(Kent-Moore No.)
Tool name
— Measuring brake pedal height
(J-46532)
Brake and clutch pedal height mea-
surement tool

LFIA0227E

38-PFM90.5 Turning rotors

( — )
Pro-Cut PFM 90 On-Car Brake Lathe

ALFIA0092ZZ

Commercial Service Tool INFOID:0000000006152271

Tool name Description

1 Flare nut crowfoot Removing and installing each brake piping
2 Torque wrench a: 10 mm (0.39 in)/12mm (0.47 in)

S-NT360

Pin punch Removing and installing reservoir tank pin

Tip diameter: 4 mm (0.16 in) dia.

ZZA0515D

Revision: July 2010 BR-4 2011 Sentra

 PREPARATION
< SERVICE INFORMATION >
Tool name Description
A
Brake fluid pressure gauge Measuring brake fluid pressure

C
NT151

Power tool Removing nuts, bolts, and screws

PIIB1407E

BR

Revision: July 2010 BR-5 2011 Sentra

 ×: Applicable
Symptom
Reference page

Revision: July 2010

Noise
Shake
Possible cause and
SUSPECTED PARTS

Shimmy, Shudder
< SERVICE INFORMATION >

Pads/Lining damaged BR-23, BR-40

×
NVH Troubleshooting Chart

Pads/Lining - uneven wear BR-23, BR-40

×
Shims damaged —

×
Rotor imbalance BR-28

×
×
Rotor damage BR-28

×
Rotor runout BR-28

BR-6
Rotor deformation BR-28

×
×
Rotor deflection BR-28

×
Rotor rust —

×
Rotor thickness variation BR-28

×
Drum out of round BR-40

FAX-5, "NVH Troubleshooting Chart",

WHEEL HUB
×
×

RAX-5, "NVH Troubleshooting Chart"

FSU-6, "NVH Troubleshooting Chart",
×
×

SUSPENSION
×

RSU-5, "NVH Troubleshooting Chart"

×
×

TIRES WT-5, "NVH Troubleshooting Chart"

×
×
×
×

ROAD WHEEL WT-5, "NVH Troubleshooting Chart"

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING

×
×

DRIVE SHAFT FAX-5, "NVH Troubleshooting Chart"

Use the chart below to help you find the cause of the symptom. If necessary, repair or replace these parts.

×
×
×

STEERING PS-5, "NVH Troubleshooting Chart"

2011 Sentra
INFOID:0000000006152272
 BRAKE PEDAL
< SERVICE INFORMATION >
BRAKE PEDAL
A
Inspection and Adjustment INFOID:0000000006152273

INSPECTION B
1. Inspect the brake pedal height (H) from the floor using Tool at a
90° angle to the floor.
C
Tool number : — (J-46532)
2. Adjust the brake pedal height to specification.
D

BR

AWFIA0557ZZ
I
Brake Pedal Specifications
Brake pedal height (H)
Refer to BR-46, "Brake Pedal".
(from dash lower panel top surface) J
Brake pedal full stroke (S) Refer to BR-46, "Brake Pedal".
Clearance between pedal stopper bracket and threaded end of the stop lamp
Refer to BR-46, "Brake Pedal".
switch (C1) and ASCD cancel switch (C2), if equipped. K

ADJUSTMENT
L

Revision: July 2010 BR-7 2011 Sentra

 BRAKE PEDAL
< SERVICE INFORMATION >
1. Loosen stop lamp switch and ASCD switch (if equipped) by
rotating it counterclockwise by 45°.
2. Loosen lock nut on input rod, then rotate input rod to set pedal to
the specified height, and tighten lock nut.
CAUTION:
Make sure that the threaded end of input rod stays inside
clevis.

Lock nut : Refer to BR-8, "Removal and Installation".

3. With the pedal pulled and held by hand, press stop lamp switch
or ASCD switch (if equipped) until its threaded end contacts
brake pedal lever.
4. With the threaded end of stop lamp switch or ASCD switch (if
equipped) contacting brake pedal lever, rotate the switch clock-
wise by 45° to secure.
CAUTION:
Make sure that the clearance (C) is within the specification.
5. Check that the stop lamps go out when the brake pedal is
released
CAUTION:
Make sure that stop lamps go off when brake pedal is
released. SFIA3064E

6. Start the engine and check the brake pedal for smooth operation.
Removal and Installation INFOID:0000000006152274

COMPONENTS

AWFIA0551GB

1. Clevis pin 2. ASCD switch (if equipped) 3. Clip

4. Stop lamp switch 5. Brake pedal assembly 6. Brake pedal pad
7. Snap pin

NOTE:
The clevis pin must be installed from the right side as shown above.
REMOVAL
1. Disconnect accelerator pedal position sensor harness connector.
2. Remove stop lamp switch and ASCD switch (if equipped) from brake pedal assembly.

Revision: July 2010 BR-8 2011 Sentra

 BRAKE PEDAL
< SERVICE INFORMATION >
3. Remove snap pin and clevis pin from clevis of brake booster.
A

SFIA2044E

D
4. Remove nuts from brake pedal bracket, and remove brake pedal assembly.
5. Remove accelerator pedal from brake pedal assembly.
INSPECTION AFTER REMOVAL E
• Check brake pedal for bend, damage, and cracks on the welded parts.
• Replace brake pedal assembly if any non-standard condition is detected.
• Check clevis pin and plastic stopper for damage and deformation. BR
Replace clevis pin as necessary.

SBR997 I
INSTALLATION
Installation is in the reverse order of the removal.
• After installing brake pedal assembly, adjust brake pedal. Refer to BR-7, "Inspection and Adjustment". J
• After installing accelerator pedal, check accelerator pedal for proper operation.
NOTE:
The clevis pin must be installed from the right side. K

Revision: July 2010 BR-9 2011 Sentra

 BRAKE FLUID
< SERVICE INFORMATION >
BRAKE FLUID
On Board Inspection INFOID:0000000006152275

CHECKING BRAKE FLUID LEVEL

• Make sure the fluid level in the reservoir tank is between MAX and
MIN lines (A) as shown.

ALFIA0169ZZ

• Visually check around the reservoir tank for fluid leakage.

• If fluid level is excessively low, check brake system for fluid leak-
age.

SBR389C

• Release parking brake lever and see if brake warning lamp goes off. If not, check brake system for fluid leak-
age.
Drain and Refill INFOID:0000000006152276

CAUTION:
• Refill using recommended brake fluid.
• Never reuse drained brake fluid.
• Be careful not to splash brake fluid on painted areas; it may cause paint damage. If brake fluid is
splashed on painted areas, immediately wipe them with cloth and wash it away with water.
• Before working, disconnect connectors of ABS actuator and electric unit (control unit) or battery
negative terminal if equipped.
1. Connect a vinyl tube to bleed valve.
2. Depress the brake pedal, loosen the bleed valve, and gradually
remove the brake fluid.

WFIA0512E

Revision: July 2010 BR-10 2011 Sentra

 BRAKE FLUID
< SERVICE INFORMATION >
3. Clean inside of reservoir tank, and refill with new brake fluid.
4. Loosen bleed valve, depress brake pedal slowly to full stroke A
and then release it. Repeat the procedure every 2 or 3 seconds
until the new brake fluid comes out, then close the bleed valve
while depressing the brake pedal. Repeat the same procedure B
for each wheel.

5. Bleed air. Refer to BR-11, "Bleeding Brake System".

C

WFIA0513E

D
Bleeding Brake System INFOID:0000000006152277

CAUTION:
• While bleeding, pay attention to master cylinder fluid level. E
• Before working, disconnect connectors of ABS actuator and electric unit (control unit) or the battery
negative terminal if equipped.
1. Connect a vinyl tube to the rear right bleed valve. BR
2. Fully depress brake pedal 4 to 5 times.
3. With brake pedal depressed, loosen bleed valve to let the air out, and then tighten it immediately.
4. Repeat steps 2, 3 until no more air comes out. G
5. Tighten bleed valve to specified torque. Refer to BR-23, "Component" (front disc brake), BR-40, "Compo-
nent" (rear drum brake), BR-32, "Component" (rear disc brake).
6. Following the steps 1 to 5 above, with master cylinder reservoir tank filled at least half way, bleed air from H
the rear right, front left, rear left, and front right brake, in that order.

Revision: July 2010 BR-11 2011 Sentra

 BRAKE TUBE AND HOSE
< SERVICE INFORMATION >
BRAKE TUBE AND HOSE
Hydraulic Circuit INFOID:0000000006152278

MR20DE with ABS or VDC/TCS/ABS

AWFIA0739ZZ

ABS actuator and electric unit

1. 2. Brake master cylinder 3. Brake booster
(control unit)
4. Connector A. Union bolt (front disc brake) B. Rear tube connector (rear drum brake)
18 N·m (1.8 kg-m, 13 ft-lb) 16.5 N·m (1.7 kg-m, 12 ft-lb)
C. Flare nut D. Flare nut – Brake tube
16.5 N·m (1.7 kg-m, 12 ft-lb) 26 N·m (2.7 kg-m, 19 ft-lb)
= Brake hose

Revision: July 2010 BR-12 2011 Sentra

 BRAKE TUBE AND HOSE
< SERVICE INFORMATION >
QR25DE with VDC/TCS/ABS
A

BR

H
AWFIA0543ZZ

ABS actuator and electric unit

1. 2. Brake master cylinder 3. Brake booster
(control unit) I
4. Connector A. Union bolt (front disc brake) B. Union bolt (rear disc brake)
18 N·m (1.8 kg-m, 13 ft-lb) 18.5 N·m (1.9 kg-m, 14 ft-lb)
C. Flare nut – Brake tube = Brake hose J
16.5 N·m (1.7 kg-m, 12 ft-lb)

CAUTION:
• All tubes and hoses must be free from excessive bending, twisting and pulling. K
• Make sure there is no interference with other parts when turning steering both clockwise and coun-
terclockwise.
• Brake tubes and hoses are an important safety part. Always disassemble the parts and retighten
their fittings, if a brake fluid leak is detected. Replace applicable part with a new one, if damaged part L
is detected.
• Be careful not to splash brake fluid on painted areas; it way cause paint damage. If brake fluid is
splashed on painted surfaces of body, immediately wipe them with cloth and then wash it away with M
water.
• Do not bend or twist brake hose sharply, or strongly pull it.
• When removing components, cover brake line connections so that dirt, dust, or other foreign mat-
N
ters do not get in.
• Refill using new recommended brake fluid.
• Never reuse drained brake fluid.
O
Front Brake Tube and Hose INFOID:0000000006152279

REMOVAL
P
CAUTION:
• Be careful not to splash brake fluid on painted areas; it may cause paint damage. If brake fluid is
splashed on painted areas, wash it away with water immediately.
• Cover the open end of brake tubes and hoses when disconnecting to prevent entrance of dirt.

Revision: July 2010 BR-13 2011 Sentra

 BRAKE TUBE AND HOSE
< SERVICE INFORMATION >
1. Remove the brake tube from brake hose using suitable tool.
NOTE:
Cap or plug opening(s) to prevent fluid from spilling.
2. Remove the union bolt and brake hose from caliper assembly.
NOTE:
Cap or plug opening(s) to prevent fluid from spilling.
3. Remove the lock plate and brake hose from the vehicle.

SFIA1118E

INSTALLATION
CAUTION:
• All brake hoses and tubes must be free from excessive bending, twisting and pulling.
• Make sure that there is no interference with other parts when turning steering both clockwise and
counterclockwise.
• Brake tubes and hoses are an important safety part. Always disassemble the parts and retighten
their fittings, if a brake fluid leak is detected. Replace applicable part with a new one, if damaged part
is detected.
• Be careful not to splash brake fluid on painted areas; it may cause paint damage. If brake fluid is
splashed on painted areas, wash it away with water immediately.
• Refill with new brake fluid “DOT 3”.
• Never reuse drained brake fluid.
1. Assemble union bolt and copper washers to brake hose.
CAUTION:
Do not reuse copper washers.
2. Position the L-shape metal fitting of the brake hose to the brake
caliper assembly positioning hole.
3. Tighten union bolt to the specified torque. Refer to BR-12,
"Hydraulic Circuit".
4. Connect brake hose to brake tube on vehicle, and temporarily
tighten flare nut by hand as much as possible.
5. Secure the brake hose with lock plate.
6. Tighten the flare nut to the specified torque using suitable tool.
Refer to BR-12, "Hydraulic Circuit".
7. Refill the brake fluid and bleed the air from the brake system. SFIA1137E
Refer to BR-11, "Bleeding Brake System".
Rear Brake Tube and Hose INFOID:0000000006152280

OVER AXLE REAR BRAKE HOSE

Removal
CAUTION:
• Be careful not to splash brake fluid on painted areas; it may cause paint damage. If brake fluid is
splashed on painted areas, wash it away with water immediately.
• Cover the open end of brake tubes and hoses when disconnecting to prevent entrance of dirt.
1. Remove the brake tube from brake hose using a suitable tool.
NOTE:
Cap or plug opening(s) to prevent fluid from spilling.
2. Remove the lock plate and brake hose.
NOTE:
Cap or plug opening(s) to prevent fluid from spilling.

SFIA1120E

Revision: July 2010 BR-14 2011 Sentra

 BRAKE TUBE AND HOSE
< SERVICE INFORMATION >
Installation
CAUTION: A
• All brake hoses and tubes must be free from excessive bending, twisting and pulling.
• Make sure that there is no interference with other parts when turning steering both clockwise and
counterclockwise.
B
• Brake tubes and hoses are an important safety part. Always disassemble the parts and retighten
their fittings, if a brake fluid leak is detected. Replace applicable part with a new one, if damaged part
is detected.
• Be careful not to splash brake fluid on painted areas; it may cause paint damage. If brake fluid is C
splashed on painted areas, wash it away with water immediately.
• Refill with new brake fluid “DOT 3”.
• Never reuse drained brake fluid. D
1. Connect brake hose to brake tube on vehicle, and temporarily tighten flare nut by hand as much as possi-
ble.
2. Secure the brake hose to bracket with lock plate. E
3. Tighten flare nut to the specified torque using a suitable tool. Refer to BR-12, "Hydraulic Circuit".
4. Refill the brake fluid and bleed the air from the brake system. Refer to BR-11, "Bleeding Brake System".
REAR BRAKE HOSE - QR25DE BR

Removal
CAUTION:
G
• Be careful not to splash brake fluid on painted areas; it may cause paint damage. If brake fluid is
splashed on painted areas, wash it away with water immediately.
• Cover the open end of brake tubes and hoses when disconnecting to prevent entrance of dirt.
1. Disconnect the brake hose from brake tube using suitable tool. H
NOTE:
Cap or plug opening(s) to prevent fluid from spilling.
I

K
LFIA0238E
2. Remove the union bolt (A), and then remove brake hose from
brake caliper assembly and discard the copper washers.
CAUTION: L
Do not reuse the copper washers.
NOTE:
Cap or plug opening(s) to prevent fluid from spilling.
M

N
AWFIA0505ZZ

3. Remove the lock plate and brake hose from the vehicle. O

Installation
CAUTION: P
• All brake hoses and tubes must be free from excessive bending, twisting and pulling.
• Make sure that there is no interference with other parts when turning steering both clockwise and
counterclockwise.
• Brake tubes and hoses are an important safety part. Always disassemble the parts and retighten
their fittings, if a brake fluid leak is detected. Replace applicable part with a new one, if damaged part
is detected.
• Be careful not to splash brake fluid on painted areas; it may cause paint damage. If brake fluid is
splashed on painted areas, wash it away with water immediately.
Revision: July 2010 BR-15 2011 Sentra
 BRAKE TUBE AND HOSE
< SERVICE INFORMATION >
• Refill with new brake fluid “DOT 3”.
• Never reuse drained brake fluid.
1. Assemble the union bolt and the new copper washers on the
brake hose.
CAUTION:
Do not reuse the copper washers.
2. Attach L-shape metal fitting of the brake hose to brake caliper
assembly positioning hole, and then tighten union bolt to the
specified torque.

SFIA1137E

3. Connect brake hose to brake tube, partially tighten flare nut by

hand as much as possible, then secure it to the bracket with lock
plate.
4. Using a flare nut torque wrench, tighten flare nut to the specified
torque.
5. Refill the brake fluid and bleed the air from the brake system.
Refer to BR-11, "Bleeding Brake System".

LFIA0238E

Inspection After Installation INFOID:0000000006152281

CAUTION:
• Always disassemble the parts and retighten their fittings, if a brake fluid leak is detected. Replace
applicable part with a new one, if damaged part is detected.
• If leak is detected at the connections, retighten it or replace the damaged part.
1. Check brake hose, tube, and connections for fluid leaks, damage, twist, deformation, contact with other
parts, and loose connections.
2. While depressing pedal under a force of 785 N (80 kg-f, 177 lb-f) with the engine running for approxi-
mately 5 seconds, check for fluid leak from each part.

Revision: July 2010 BR-16 2011 Sentra

 BRAKE MASTER CYLINDER
< SERVICE INFORMATION >
BRAKE MASTER CYLINDER
A
On-Board Inspection INFOID:0000000006152284

LEAK INSPECTION B
Check for leaks in a master cylinder installation surface, the reservoir tank installation surface, and the brake
tube connections. Repair or replace components as necessary.
Removal and Installation INFOID:0000000006152285
C

BR

K
AWFIA0545GB

1. Reservoir cap 2. Filter 3. Brake fluid level switch connector

4. Master cylinder and reservoir 5. Hose to clutch master cylinder 6. O-ring L
assembly (if equipped)

CAUTION:
Be careful not to splash brake fluid on painted areas; it may cause paint damage. If brake fluid is M
splashed on painted areas, immediately wipe them with cloth and wash it away with water.
REMOVAL
N
1. Drain the brake fluid. Refer to BR-10, "Drain and Refill".
2. Remove the battery and battery tray as necessary. Refer to SC-7, "Removal and Installation (MR20DE
Battery)", SC-9, "Removal and Installation (QR25DE Battery Tray)". O
3. Remove the air cleaner and air duct. Refer to EM-16, "Removal and Installation" (MR20DE), EM-133,
"Removal and Installation" (QR25DE).
4. Disconnect the brake fluid level switch harness connector. P
5. Disconnect the hose to clutch master cylinder (if equipped) from the brake fluid reservoir.
NOTE:
Cap or plug opening(s) to prevent fluid from spilling.
6. Remove the brake tubes from master cylinder using a suitable tool.
NOTE:
Cap or plug opening(s) to prevent fluid from spilling.

Revision: July 2010 BR-17 2011 Sentra

 BRAKE MASTER CYLINDER
< SERVICE INFORMATION >
7. Remove the master cylinder and reservoir assembly nuts, and remove the master cylinder and reservoir
assembly.
INSTALLATION
CAUTION:
• Refill using recommended brake fluid.
• Never reuse drained brake fluid.
• Check if the rod of primary piston has dust or scratches.
1. Install master cylinder and reservoir assembly to brake booster
assembly, and tighten master cylinder and reservoir assembly
nuts to the specified torque.
CAUTION:
• Do not damage or strain rod of primary piston.
• Apply silicone grease for O-ring, primary piston rod and
to inside of booster.

SFIA2614E

2. Install brake tubes to master cylinder, then tighten flare nuts to the specified torque using a suitable tool.
Refer to BR-12, "Hydraulic Circuit".
3. Connect the hose to clutch master cylinder (if equipped) from the brake fluid reservoir.
4. Connect brake fluid level switch harness connector and clutch master cylinder hose (if equipped).
5. Install the air cleaner and air duct. Refer to EM-16, "Removal and Installation" (MR20DE), EM-133,
"Removal and Installation" (QR25DE).
6. Install the battery and battery tray as necessary. Refer to SC-7, "Removal and Installation (MR20DE Bat-
tery)", SC-9, "Removal and Installation (QR25DE Battery Tray)".
7. Refill with new brake fluid and bleed the air from the brake system and clutch system (if equipped). Refer
to BR-11, "Bleeding Brake System", or CL-9, "Air Bleeding Procedure".

Revision: July 2010 BR-18 2011 Sentra

 BRAKE BOOSTER
< SERVICE INFORMATION >
BRAKE BOOSTER
A
On Board Inspection INFOID:0000000006152286

OPERATING CHECK B
• With the engine stopped, change the vacuum to the atmospheric
pressure by depressing brake pedal several times at intervals of 5
seconds. C
• Then with brake pedal fully depressed, start engine and when the
vacuum pressure reaches the standard, make sure that the clear-
ance between brake pedal and floor panel decreases.
D

E
WFIA0520E

AIRTIGHT CHECK
BR
• Run engine at idle for approximately 1 minute, and stop it after
applying vacuum to booster. Depress brake pedal normally to
change the vacuum to the atmospheric pressure. Make sure that
distance between brake pedal and floor panel gradually increases. G
• Depress the brake pedal while engine is running, then stop engine
with brake pedal depressed. The pedal stroke should not change
after holding pedal down for 30 seconds. H

I
WFIA0521E

Removal and Installation INFOID:0000000006152287

J
COMPONENTS

ALFIA0170GB

Revision: July 2010 BR-19 2011 Sentra

 BRAKE BOOSTER
< SERVICE INFORMATION >

1. Reservoir tank 2. Master cylinder 3. Gasket

4. Clevis 5. Spacer 6. Brake booster
7. Lower dash assembly A. Up mark

REMOVAL
CAUTION:
• Be careful not to splash brake fluid on painted areas such as body. It may cause paint damage. If
brake fluid is splashed on painted surfaces of body, wipe them with cloth immediately and then wash
it away with water.
• Be careful not to deform or bend brake tubes while removing and installing brake booster.
• Replace clevis pin if it is damaged.
• Be careful not to damage brake booster stud bolt threads. If brake booster is tilted or inclined during
installation, dash panel may damage the threads.
1. Remove vacuum hose from brake booster. Refer to BR-21, "Removal and Installation".
2. Remove master cylinder assembly. Refer to BR-17, "Removal and Installation".
3. Remove LH instrument panel lower finisher. Refer to IP-12, "Removal and Installation".
4. Remove snap pin and clevis pin from the clevis of the input rod,
and disconnect clevis from brake pedal.
5. Disconnect accelerator pedal assembly connector.
6. Remove the three brake pedal nuts from lower dash assembly.
7. Remove the spacer nut from lower dash assembly.
8. Remove brake booster and spacer.
9. Remove brake booster nuts and remove spacer from brake
booster.

SFIA2044E

INSTALLATION
1. Loosen lock nut to adjust input rod length so that the length (B)
satisfies the specified value.

Length (B) : Refer to BR-47, "Brake Booster".

2. Install spacer with new gasket to brake booster and tighten
spacer nut (brake booster side) to the specified torque.
3. After adjusting length (B), temporarily tighten lock nut to install
brake booster assembly to lower dash assembly. At this time,
make sure to install a gasket between brake booster and lower
dash assembly. SGIA0060E
CAUTION:
Be sure to install the gasket between brake booster and lower dash assembly.
4. Connect brake pedal to clevis of input rod with the clevis pin and snap pin.
5. Install the three brake pedal bracket nuts and tighten them to the specified torque.
6. Connect accelerator pedal assembly connector.
7. Install the spacer nut and tighten to the specified torque.
8. Adjust the height of brake pedal. Refer to BR-7, "Inspection and Adjustment".
9. Tighten lock nut for the input rod to the specified torque.
10. Install LH instrument panel lower finisher. Refer to IP-12, "Removal and Installation"
11. Install vacuum hose into brake booster. Refer to BR-21, "Removal and Installation".
12. Install master cylinder assembly. Refer to BR-17, "Removal and Installation".
13. Refill with new brake fluid and bleed the air from the brake system and clutch system (if equipped). Refer
to BR-11, "Bleeding Brake System".

Revision: July 2010 BR-20 2011 Sentra

 VACUUM LINES
< SERVICE INFORMATION >
VACUUM LINES
A
Component INFOID:0000000006152288

BR

LFIA0256E

1. Clamp 2. Engine side indicator stamp (for built-in 3. Vacuum hose

G
check valve)
4. Clip A. To intake manifold B. To brake booster
H
Removal and Installation INFOID:0000000006152289

REMOVAL I
1. Disconnect the vacuum hose from the brake booster.
2. Disconnect the vacuum hose from the engine intake manifold.
3. Remove the vacuum hose. J

INSTALLATION
Installation is in the reverse order of removal.
K
• Inspect the vacuum hose and internal one-way check valve before installation. Refer to BR-21, "Inspection".
CAUTION:
• Because the vacuum hose contains a one-way check valve, the hose must be installed in the correct
position. Refer to the stamp on the hose to confirm the correct direction for installation. The brake L
booster will not operate normally if the hose is installed in the wrong direction.
• Do not use lubricating oil during assembly.
• Insert the vacuum hose at least 24 mm (0.94 in) onto the brake M
booster fitting as shown.

SBR225B
P
Inspection INFOID:0000000006152290

VISUAL INSPECTION
Check for improper installation, damage and aging. Reinstall or replace the vacuum hose with the internal
check valve as necessary.
CHECK VALVE INSPECTION

Revision: July 2010 BR-21 2011 Sentra

 VACUUM LINES
< SERVICE INFORMATION >
• Use a hand vacuum pump to inspect the vacuum hose and internal
check valve. Replace the vacuum hose and internal check valve if
not within specifications.

When connected to booster side (1) Refer to BR-46,

"Check Valve".
When connected to engine side (2) Refer to BR-46,
"Check Valve".

SFIA0210E

• Replace the vacuum hose with the internal check valve if the vacuum hose is damaged or deformed.

Revision: July 2010 BR-22 2011 Sentra

 FRONT DISC BRAKE
< SERVICE INFORMATION >
FRONT DISC BRAKE
A
On Board Inspection INFOID:0000000006152291

PAD WEAR INSPECTION B

Inspect pad thickness from check hole in cylinder body. Refer to BR-
47, "Front Disc Brake".
C

E
BRA0010D

Component INFOID:0000000006152292
BR
Front Disc Brakes - MR20DE (All Models) & QR25DE (SE-R)
G

AWFIA0628GB N

1. Union bolt 2. Brake hose 3. Copper washer

4. Cap 5. Bleed valve 6. Sliding pin bolt
O
7. Cylinder body 8. Piston seal 9. Piston
10. Piston boot 11. Inner shim cover 12. Inner shim
13. Inner pad 14. Pad wear sensor 15. Pad retainer
P
16. Outer pad 17. Outer shim 18. Outer shim cover
19. Sliding pin 20. Sliding pin boot 21. Bushing
22. Torque member bolt 23. Torque member Front
A. Molykote AS-880N grease B. Rubber grease C. Molykote M-7439 grease
D. Brake fluid E. SE-R only

Revision: July 2010 BR-23 2011 Sentra

 FRONT DISC BRAKE
< SERVICE INFORMATION >
Front Disc Brakes - QR25DE (SE-R SPEC -V)

AWFIA0627GB

1. Union bolt 2. Brake hose 3. Copper washer

4. Cap 5. Bleed valve 6. Sliding pin bolt
7. Cylinder body 8. Piston seal 9. Piston
10. Piston boot 11. Inner shim cover 12. Inner shim
13. Inner pad 14. Pad wear sensor 15. Pad retainer
16. Outer pad 17. Outer shim 18. Outer shim cover
19. Sliding pin 20. Sliding pin boot 21. Bushing
22. Torque member bolt 23. Torque member Front
A. Molykote AS-880N grease B. Rubber grease C. Molykote M-7439 grease
D. Brake fluid

CAUTION:
Clean dust with a vacuum dust collector. Do not blow with compressed air.
Removal and Installation of Brake Pad INFOID:0000000006152293

WARNING:
Clean dust on caliper and brake pad with a vacuum dust collector to minimize the hazard of air borne
particles or other materials.
CAUTION:
• While removing caliper, do not depress brake pedal because piston will pop out.
• It is not necessary to remove bolts on torque member and brake hose except for disassembly or
replacement of caliper assembly. In this case, hang caliper with a wire so as not to stretch brake
hose.
• Do not damage piston boot.
• If any shim is subject to serious corrosion, replace it with a new one.
• Always replace shim and shim cover as a set when replacing brake pads.
• Keep rotor free from brake fluid.
• Burnish the brake pads and disc rotor mutually contacting surfaces, after refinishing or replacing
rotors, after replacing pads, or if a soft pedal occurs at very low mileage. Refer to WT-7, "Adjust-
ment".
REMOVAL
Revision: July 2010 BR-24 2011 Sentra
 FRONT DISC BRAKE
< SERVICE INFORMATION >
1. Remove front wheels and tires using power tools.
2. Remove lower sliding pin bolt. A

SBR976B
D

3. Swing cylinder body up and support cylinder body with a suit-

able wire as shown. Remove pads, shims and pad retainers E
from torque member.

BR

SBR932C

H
CAUTION:
When removing pad retainer from torque member, lift pad
retainer in the direction shown by arrow, so as not to I
deform it.

SBR556E

L
INSTALLATION
1. Apply Molykote AS-880N grease or equivalent to the shims. Install shims to pads.
CAUTION:
Securely install shims according to mounting direction of pads. M
2. Apply Molykote M-7439 grease or equivalent to pad contact sur-
faces (A) on pad retainers. Install pad retainers and pads to the
torque member. N

P
AWFIA0039ZZ

CAUTION:

Revision: July 2010 BR-25 2011 Sentra

 FRONT DISC BRAKE
< SERVICE INFORMATION >
• When installing pad retainer, attach it firmly so that it is
not lifted up from torque member, as shown.

PFIA0273E

• If equipped, both inner and outer pads have a pad return

system on the pad retainer. Install pad return lever
securely to pad wear sensor.

SBR557E

3. On SE-R models, apply Molykote AS-880N grease to inside of cylinder fingers.

4. Install the cylinder body to torque member.
• Press the piston into the cylinder body using a suitable tool.
CAUTION:
Check the brake fluid level in the reservoir tank because brake fluid returns to master cylinder res-
ervoir tank when pressing piston in.
5. Install lower sliding pin bolt, and tighten to the specified torque.
Refer to BR-23, "Component".

SBR976B

6. Check front brakes for drag.

7. Install front wheels and tires. Refer to WT-7, "Adjustment".
Removal and Installation of Brake Caliper Assembly INFOID:0000000006152294

WARNING:
Clean dust on caliper and brake pad with a vacuum dust collector to minimize the hazard of air borne
particles or other materials.
CAUTION:
• While removing caliper, do not depress brake pedal because piston will pop out.
• It is not necessary to remove bolts on torque member and brake hose except for disassembly or
replacement of caliper assembly. In this case, hang caliper with a wire so as not to stretch brake
hose.
• Do not damage piston boot.
• If any shim is subject to serious corrosion, replace it with a new one.
• Always replace shim and shim cover as a set when replacing brake pads.

Revision: July 2010 BR-26 2011 Sentra

 FRONT DISC BRAKE
< SERVICE INFORMATION >
• Keep rotor free from brake fluid.
• Burnish the brake pads and disc rotor mutually contacting surfaces, after refinishing or replacing A
rotors, after replacing pads, or if a soft pedal occurs at very low mileage. Refer to BR-31, "Brake Bur-
nishing".
REMOVAL B
1. Remove front wheels and tires using power tools.
2. Secure disc rotor using wheel nuts.
C
3. Remove union bolt (A), and then disconnect brake hose from
cylinder body. Discard the copper washers.
• Protrusions (B)
CAUTION: D
Do not reuse the copper washers.
NOTE:
Cap or plug opening(s) to prevent fluid fro spilling. E

BR
AWFIA0502ZZ

4. Remove sliding pin bolts (A) and remove cylinder body from
torque member. G

AWFIA0548ZZ
J
5. If necessary, apply matching marks then remove wheel nuts and
remove disc rotor.
CAUTION: K
Put matching marks on wheel hub assembly and disc rotor
as shown, if it is necessary to remove disc rotor.
L

M
SDIA2608E

INSTALLATION
N
1. If removed, install disc rotor and secure using wheel nuts.
CAUTION:
Follow matching marks on wheel hub assembly and disc
rotor for installation as shown. O

SDIA2608E

Revision: July 2010 BR-27 2011 Sentra

 FRONT DISC BRAKE
< SERVICE INFORMATION >
2. Install cylinder body on sliding pins, and tighten sliding pin bolts
(A) to the specified torque. Refer to BR-23, "Component".
CAUTION:
Before installing cylinder body, wipe off all oil and grease
on mounting surface of torque member.

AWFIA0548ZZ

3. Install brake hose to cylinder body with new copper washers.

Align the brake hose tab between the protrusions (B) on the cyl-
inder body as shown. Tighten the union bolt (A) to specification.
Refer to BR-12, "Hydraulic Circuit".

AWFIA0502ZZ

CAUTION:
Do not reuse copper washers.

SFIA1137E

4. Check front disc brake for drag.

5. Bleed the brake system. Refer to BR-11, "Bleeding Brake System".
6. Install front wheels and tires. Refer to WT-7, "Adjustment".
Disassembly and Assembly of Brake Caliper Assembly INFOID:0000000006152295

WARNING:
Clean dust on caliper and brake pad with a vacuum dust collector to minimize the hazard of air borne
particles or other materials.
CAUTION:
• While removing caliper, do not depress brake pedal because piston will pop out.
• It is not necessary to remove bolts on torque member and brake hose except for disassembly or
replacement of caliper assembly. In this case, hang caliper with a wire so as not to stretch brake
hose.
• Do not damage piston boot.
• If any shim is subject to serious corrosion, replace it with a new one.
• Always replace shim and shim cover as a set when replacing brake pads.
• Keep rotor free from brake fluid.
• Burnish the brake pads and disc rotor mutually contacting surfaces, after refinishing or replacing
rotors, after replacing pads, or if a soft pedal occurs at very low mileage. Refer to BR-31, "Brake Bur-
nishing".
NOTE:

Revision: July 2010 BR-28 2011 Sentra

 FRONT DISC BRAKE
< SERVICE INFORMATION >
Do not remove torque member, brake pads, shims and pad retainers, when disassembling or assembling cyl-
inder body. A
DISASSEMBLY
1. Remove cylinder body from the torque member. Refer to BR-26, "Removal and Installation of Brake Cali-
per Assembly". B
2. Place a wooden block as shown, and blow air from union bolt
hole to remove piston and piston boot. Discard the piston boot.
C
WARNING:
Do not place your finger in front of piston.

WFIA0525E

3. Remove piston seal using a suitable tool. Discard the piston BR

seal.
CAUTION:
Be careful not to damage the inner wall of cylinder body. G

SFIA2277E
I

INSPECTION AFTER DISASSEMBLY

Cylinder Body J
Check the inner wall of cylinder for corrosion, wear, and damage. Replace cylinder body as necessary.
CAUTION:
Clean cylinder body using new brake fluid. Never use mineral oils such as gasoline or kerosene. K
Torque Member
Check for wear, cracks, and damage. Replace torque member as necessary.
Piston L
Check piston surface for corrosion, wear, and damage. Replace piston as necessary.
CAUTION:
The piston sliding surface is plated. Do not polish with sandpaper. M
Sliding Pin, Sliding Pin Bolt, and Sliding Pin Boot
Check sliding pins, sliding pin bolts and sliding pin boots for wear, damage, and cracks. Replace affected parts
as necessary. N
ASSEMBLY
1. Apply rubber grease to new piston seal and install into cylinder
O
body.

SFIA2278E

Revision: July 2010 BR-29 2011 Sentra

 FRONT DISC BRAKE
< SERVICE INFORMATION >
2. Apply rubber grease to new piston boot and apply brake fluid to
piston. Cover the piston end with piston boot, and install cylin-
der-side lip on piston boot properly into groove on cylinder body
using a suitable tool.

SFIA3074E

3. Press piston into cylinder body by hand to assemble piston-side

lip on piston boot properly into a groove on piston.
CAUTION:
Press piston evenly and change pressing point to prevent
inner wall of cylinder from being rubbed.

SFIA2279E

4. Install the cylinder body on the torque member. Refer to BR-26, "Removal and Installation of Brake Cali-
per Assembly".
DISC ROTOR INSPECTION
Visual Inspection
Check surfaces of disc rotor for uneven wear, cracks or serious damage. Replace as necessary.
Runout Inspection
1. Secure disc rotor to wheel hub at two or more positions using wheel nuts.
2. Inspect runout using a dial gauge located at a point 10 mm (0.39
in) from the edge.
CAUTION:
Make sure that wheel bearing axial end play is within the
specifications before measuring runout. Refer to FAX-6,
"On-Vehicle Inspection and Service".

Runout limit : Refer to BR-47, "Front Disc Brake".

SBR019B

3. If runout is outside the limit, find the minimum runout point by shifting the mounting positions of disc rotor
and wheel hub by one hole.
4. If runout is still out of specification, turn the disc rotor using Tool until runout is with the specified limit.

Tool number : 38-PFM90.5 ( — )

Thickness Inspection

Revision: July 2010 BR-30 2011 Sentra

 FRONT DISC BRAKE
< SERVICE INFORMATION >
Using a micrometer, check thickness of disc rotor. If thickness is out-
side the specification, replace disc rotor. A

Repair limit thickness : Refer to BR-47, "Front Disc

Brake". B

SBR020B

D
Brake Burnishing INFOID:0000000006152296

Burnish the new braking surfaces according to following procedure after refinishing or replacing disc rotors,
pads, or if a soft pedal occurs at very low mileage. E
CAUTION:
• Be careful of vehicle speed because brake does not operate easily until pad and disc rotor are
securely fitted. BR
• Only perform this procedure under safe road and traffic conditions. Use extreme caution.
1. Drive vehicle on straight, flat road.
2. Depress brake pedal with the power to stop vehicle within 3 to 5 seconds until the vehicle stops. G
3. Drive without depressing brake pedal for a few minutes to cool brake.
4. Repeat steps 1 to 3 until pad and disc rotor are securely fitted.
H

Revision: July 2010 BR-31 2011 Sentra

 REAR DISC BRAKE
< SERVICE INFORMATION >
REAR DISC BRAKE
On Board Inspection INFOID:0000000006152297

PAD WEAR INSPECTION

Inspect pad thickness from check hole in cylinder body. Refer to BR-
47, "Rear Disc Brake".

BRA0010D

Component INFOID:0000000006152298

AWFIA0629GB

1. Union bolt 2. Brake hose 3. Copper washer

4. Cap 5. Air bleeder 6. Sliding pin
7. Cylinder body 8. Piston seal 9. Piston
10. Piston boot 11. Retaining ring 12. Inner shim cover
13. Inner shim 14. Inner pad 15. Pad retainer
16. Outer pad 17. Outer cover (multi-layer) 18. Sliding pin boot
19. Torque member bolts 20. Torque member Front
A. Molykote AS-880N grease B. Brake fluid C. Rubber grease

Revision: July 2010 BR-32 2011 Sentra

 REAR DISC BRAKE
< SERVICE INFORMATION >
CAUTION:
• Clean dust with a vacuum dust collector. Do not blow with compressed air. A
• Make sure parking brake lever is released completely.
Removal and Installation of Brake Pad INFOID:0000000006152299
B
WARNING:
Clean dust on caliper and brake pad with a vacuum dust collector to minimize the hazard of air borne
particles or other materials. C
CAUTION:
• While removing caliper, do not depress brake pedal because piston will pop out.
• It is not necessary to remove bolts on torque member and brake hose except for disassembly or
D
replacement of caliper assembly. In this case, hang caliper with a wire so as not to stretch brake
hose.
• Do not damage piston boot.
• If any shim is subject to serious corrosion, replace it with a new one. E
• Always replace shim and shim cover as a set when replacing brake pads.
• Keep rotor free from brake fluid.
• Burnish the brake pads and disc rotor mutually contacting surfaces, after refinishing or replacing BR
rotors, after replacing pads, or if a soft pedal occurs at very low mileage. Refer to BR-39, "Brake Bur-
nishing".
REMOVAL G
1. Remove rear wheels and tires using power tool.
2. Remove lower sliding pin.
H

SBR976B

K
3. Swing cylinder body up and support cylinder body with a suit-
able wire as shown. Remove pads, shim, covers and pad retain-
ers from torque member.
L

N
SBR932C

CAUTION: O

Revision: July 2010 BR-33 2011 Sentra

 REAR DISC BRAKE
< SERVICE INFORMATION >
When removing pad retainer from torque member, lift pad
retainer in the direction shown by arrow, so as not to
deform it.

SBR556E

INSTALLATION
1. Apply Molykote AS-880N grease between the inner shim and inner shim cover. Apply Molykote AS-880N
grease inside the outer cover.
2. Attach the inner shim and inner shim cover to the inner pad, and the outer cover to the outer pad.
3. Install the pad retainers and assembled pads on the torque member.
CAUTION:
• When installing pad retainer, attach it firmly so that it is
not lifted up from torque member, as shown.

PFIA0273E

4. Install the cylinder body to the torque member.

• Press the piston into the cylinder body using a suitable tool.
CAUTION:
Check the brake fluid level in the reservoir tank because brake fluid returns to master cylinder res-
ervoir tank when pressing piston in.
5. Install the lower sliding pin and tighten to the specified torque.
Refer to BR-32, "Component".

SBR976B

6. Check rear brakes for drag.

7. Install rear wheels and tires. Refer to WT-7, "Adjustment".
Removal and Installation of Caliper Assembly INFOID:0000000006152300

WARNING:
Clean dust on caliper and brake pad with a vacuum dust collector to minimize the hazard of air borne
particles or other materials.
CAUTION:
• While removing caliper, do not depress brake pedal because piston will pop out.

Revision: July 2010 BR-34 2011 Sentra

 REAR DISC BRAKE
< SERVICE INFORMATION >
• It is not necessary to remove bolts on torque member and brake hose except for disassembly or
replacement of caliper assembly. In this case, hang caliper with a wire so as not to stretch brake A
hose.
• Do not damage piston boot.
• If any shim is subject to serious corrosion, replace it with a new one.
B
• Always replace shim and shim cover as a set when replacing brake pads.
• Keep rotor free from brake fluid.
• Burnish the brake pads and disc rotor mutually contacting surfaces, after refinishing or replacing
rotors, after replacing pads, or if a soft pedal occurs at very low mileage. Refer to WT-7, "Adjust- C
ment".
REMOVAL
D
1. Remove rear wheels and tires using power tool.
2. Secure disc rotor using wheel nuts.
3. Remove the union bolt to disconnect the rear brake hose. Discard the copper washers. E
CAUTION:
Do not reuse the copper washers.
NOTE:
Cap or plug opening(s) to prevent fluid from spilling. BR
4. Remove sliding pins (A) and remove cylinder body from torque
member.
G

I
AWFIA0550ZZ

5. If necessary, remove torque member and disc rotor. If the disc rotor cannot be removed, remove as fol- J
lows:
• Make sure parking brake lever is completely disengaged.
• Hold down the disc rotor with the wheel nut and remove the adjuster hole plug.
K
• Insert a flat-bladed screwdriver through the plug opening and
rotate the star wheel (1) on the adjuster assembly in the direc-
tion (A)shown to loosen and retract the brake shoes.
• Prior to removing disc rotor, make alignment mark using a L
marker between the hub and disc rotor.
• Remove wheel nut and rotor.
M

N
JPFIB0014ZZ

INSTALLATION
1. If necessary, install disc rotor and torque member. O
• Align marks made during removal on the hub and disc rotor.

Revision: July 2010 BR-35 2011 Sentra

 REAR DISC BRAKE
< SERVICE INFORMATION >
2. Install cylinder body to the torque member and tighten sliding
pins (A) to the specified torque. Refer to BR-32, "Component".
CAUTION:
Before installing cylinder body, wipe off oil and grease on
mounting surfaces of cylinder body.

AWFIA0550ZZ

3. Install brake hose with new copper washers to cylinder body and tighten union bolt to the specified torque.
Refer to BR-32, "Component".
CAUTION:
• Do not reuse the copper washers.
• Align brake hose protrusion to groove on cylinder body.
4. Adjust the parking brake. Refer to PB-5, "On-Vehicle Service".
5. Bleed the brake system. Refer to BR-11, "Bleeding Brake System".
6. Install rear wheels and tires. Refer to WT-7, "Adjustment".
Disassembly and Assembly of Caliper Assembly INFOID:0000000006152301

WARNING:
Clean dust on caliper and brake pad with a vacuum dust collector to minimize the hazard of air borne
particles or other materials.
CAUTION:
• While removing caliper, do not depress brake pedal because piston will pop out.
• It is not necessary to remove bolts on torque member and brake hose except for disassembly or
replacement of caliper assembly. In this case, hang caliper with a wire so as not to stretch brake
hose.
• Do not damage piston boot.
• If any shim is subject to serious corrosion, replace it with a new one.
• Always replace shim and shim cover as a set when replacing brake pads.
• Keep rotor free from brake fluid.
• Burnish the brake pads and disc rotor mutually contacting surfaces, after refinishing or replacing
rotors, after replacing pads, or if a soft pedal occurs at very low mileage. Refer to BR-39, "Brake Bur-
nishing".
NOTE:
Do not remove torque member, brake pads, shims and pad retainers, when disassembling or assembling cyl-
inder body.
DISASSEMBLY
1. Remove the cylinder body from the torque member. Refer to BR-34, "Removal and Installation of Caliper
Assembly".
2. Remove sliding pin boot from the torque member.
3. Remove the retaining ring from the cylinder body using a suit-
able tool as shown. Discard the retaining ring.
CAUTION:
Do not reuse the retaining ring.

SBR028A

Revision: July 2010 BR-36 2011 Sentra

 REAR DISC BRAKE
< SERVICE INFORMATION >
4. Place a wooden block as shown, and blow air from union bolt
hole to remove piston and piston boot. A
WARNING:
Do not place your finger in front of piston.
B

BRD0041D

D
5. Remove piston seal from cylinder body using a suitable tool as
shown.
CAUTION:
E
Be careful not to damage cylinder inner wall.

BR

G
PFIA0269E

INSPECTION AFTER DISASSEMBLY

H
Cylinder Body
Check the inner wall of cylinder for corrosion, wear, and damage. Replace cylinder body as necessary.
CAUTION:
Clean cylinder body using new brake fluid. Never use mineral oils such as gasoline or kerosene. I

Torque Member
Check for wear, cracks, and damage. Replace torque member as necessary.
J
Piston
Check piston surface for corrosion, wear, and damage. Replace piston as necessary.
CAUTION: K
The piston sliding surface is plated. Do not polish with sandpaper.
Sliding Pin and Sliding Pin Boot
Check sliding pins and sliding pin boots for wear, damage, and cracks. Replace affected parts as necessary. L
ASSEMBLY
1. Apply a rubber grease to the new piston seal and install into the
cylinder body. M
CAUTION:
Do not reuse the piston seals.
N

SFIA0156E
P

Revision: July 2010 BR-37 2011 Sentra

 REAR DISC BRAKE
< SERVICE INFORMATION >
2. Apply rubber grease to the new piston boot and install on the
piston, then firmly insert the new piston boot cylinder-side lip into
the cylinder body groove.
CAUTION:
Do not reuse the piston boot.

SFIA0157E

3. Apply a brake fluid to the piston then insert it into the cylinder
body by hand and firmly attach the new piston boot piston-side
lip into the new piston boot.
CAUTION:
Press the piston evenly and vary the pressing point to pre-
vent cylinder inner wall from being rubbed.

PFIA0272E

4. Install the new retaining ring to hold the piston boot.

CAUTION:
• Make sure the boot is firmly in the cylinder body groove.
• Do not reuse the retaining ring.

SFIA0158E

5. Attach the sliding pin boot to the torque member.

6. Install the cylinder body on the torque member. Refer to BR-34, "Removal and Installation of Caliper
Assembly".
DISC ROTOR INSPECTION
Visual Inspection
Check surface of the disc rotor for uneven wear, cracks or serious damage. Replace as necessary.
Runout Inspection
1. Secure disc rotor to the wheel hub in two or more positions, using wheel nuts.
2. Inspect runout using a dial gauge located at a point 10 mm (0.39
in) from the edge.
CAUTION:
Before measuring, make sure the axle end play is with
specification. Refer to RAX-6, "On-Vehicle Inspection and
Service".

Runout limit : Refer to BR-47, "Rear Disc Brake".

SBR019B

Revision: July 2010 BR-38 2011 Sentra

 REAR DISC BRAKE
< SERVICE INFORMATION >
3. If runout is outside the limit, find the minimum runout point by shifting mounting positions of the disc rotor
and wheel hub by one hole. A
4. If runout is still out of specification, turn the disc rotor using Tool until runout is with the specified limit.

Tool number : 38-PFM90.5 ( — ) B

Thickness Inspection
Using a micrometer, check thickness of the disc rotor. If thickness is
C
not within specification, replace disc rotor.

Repair limit thickness : Refer to BR-47, "Rear Disc

Brake". D

SBR020B
BR
Brake Burnishing INFOID:0000000006152302

Burnish the new braking surfaces according to following procedure after refinishing or replacing disc rotors, G
pads, or if a soft pedal occurs at very low mileage.
CAUTION:
• Be careful of vehicle speed because brake does not operate easily until pad and disc rotor are
H
securely fitted.
• Only perform this procedure under safe road and traffic conditions. Use extreme caution.
1. Drive vehicle on straight, flat road.
I
2. Depress brake pedal with the power to stop vehicle within 3 to 5 seconds until the vehicle stops.
3. Drive without depressing brake pedal for a few minutes to cool brake.
4. Repeat steps 1 to 3 until pad and disc rotor are securely fitted. J

Revision: July 2010 BR-39 2011 Sentra

 REAR DRUM BRAKE
< SERVICE INFORMATION >
REAR DRUM BRAKE
Component INFOID:0000000006152303

WFIA0536E

1. Back plate 2. Shoe hold pin 3. Plug

4. Plug 5. Retainer ring 6. Operating lever
7. Adjuster lever 8. Spring 9. Retainer
10. Return spring (lower side) 11. Return spring (upper side) 12. Adjuster spring
13. Adjuster 14. Brake shoe 15. Brake drum
16. Wheel cylinder 17. Spring 18. Piston cup
19. Piston 20. Boot 21. Bleed valve
22. Cap 23. Parking brake rear cable
1: NISSAN rubber lubricant 2: NISSAN brake grease : Brake fluid
(KRE12 00030) (KRF00 00005)

CAUTION:
• Clean dust on drum and back plate with a vacuum dust collector. Do not blow with compressed air.
• Make sure parking brake lever is released completely.
Removal and Installation of Drum Brake Assembly INFOID:0000000006152304

WARNING:
Clean dust with a vacuum dust collector to minimize the hazard of air borne particles or other materi-
als.
CAUTION:
• While removing brake shoes, do not depress brake pedal because wheel cylinder pistons will pop
out.
• It is not necessary to disconnect brake tube except for disassembly or replacement of wheel cylin-
der assembly.
• Keep drum free from brake fluid.
REMOVAL

Revision: July 2010 BR-40 2011 Sentra

 REAR DRUM BRAKE
< SERVICE INFORMATION >
1. Remove rear wheels and tires using power tools.
2. With the parking brake lever released, remove the brake drum. If it is difficult to remove the brake drum, A
use the following procedure.
a. Remove the plug from the back plate.
b. Press up adjuster lever with a suitable tool from the plug hole (at B
the side of wheel cylinder) on the back plate as shown. Turn the
frame of the adjuster assembly using a suitable tool in the direc-
tion that narrows the expanded brake shoes. C

SFIA3080E
E

3. While pushing and rotating the retainer, pull out the shoe hold pin, and remove the brake shoe assembly.
CAUTION: BR
Do not damage the wheel cylinder boot.

4. Disconnect the parking brake rear cable from the operating lever.
CAUTION: G
Do not bend the parking brake cable.
5. Disassemble the brake shoe assembly (brake shoes, springs, adjuster and adjuster lever).
6. Remove the retainer ring (A) with a suitable tool to separate the H
operating lever (C) from brake shoe.
• Contact point (B)
• Pin (D) I

K
SFIA3075E

INSPECTION AFTER REMOVAL

Lining Thickness Inspection L
Check lining thickness.

Standard thickness (A) : Refer to BR-48, "Rear M

Drum Brake".
Repair limit thickness (A) : Refer to BR-48, "Rear
Drum Brake". N

O
SBR021A

Drum Inner Diameter Inspection

P

Revision: July 2010 BR-41 2011 Sentra

 REAR DRUM BRAKE
< SERVICE INFORMATION >
Check inner diameter of brake drum.
Measurement area: lining contact surface (center)

Standard inner diameter : Refer to BR-48, "Rear

Drum Brake".
Repair limit inner diameter : Refer to BR-48, "Rear
Drum Brake".

SBR022A

Wheel Cylinder Leakage Inspection

• Check wheel cylinder for brake fluid leakage.
• Check for wear, damage, and looseness. If any non-standard con-
dition is found, replace it.

WFIA0528E

Other Inspections
Check the following:
• Inside of the drum for excessive wear, damage, and cracks.
• Lining for excessive wear, damage, and peeling.
• Shoe sliding surface for excessive wear and damage.
• Return spring for sagging.
• Check back plate for damage, cracks, and deformation. Replace back plate as necessary.
Replace applicable part as necessary.
INSTALLATION
1. Install the operating lever (C) using the following procedure.
a. Position operating lever (C) on brake shoe.
b. Install retainer ring (A) on operating lever (C), and crimp them
until their contact points (B) are met.
• Pin (D)

SFIA3075E

2. Apply NISSAN brake grease (KRF00 00005) to brake shoes

sliding surfaces (the shaded areas) and other parts on the back
plate as indicated by arrows.

WFIA0529E

Revision: July 2010 BR-42 2011 Sentra

 REAR DRUM BRAKE
< SERVICE INFORMATION >
3. Apply NISSAN brake grease (KRF00 00005) to screw and con-
firm the difference between right and left wheel for assembling A
when disassembled.

Right rear wheel Thread cutting : Right-hand screw B

direction
Left rear wheel Thread cutting : Left-hand screw
direction C

SFIA3076E

D
4. Assemble the shoe, adjuster, adjuster lever and springs on the shoe assembly.
5. Connect the parking brake rear cable to the operating lever.
6. Install the shoe assembly. After installation be sure that each part is installed properly. E
CAUTION:
Do not damage the wheel cylinder piston boot.
7. Install the brake drum. BR
8. Depress brake pedal approximately 2 to 3 times.
9. Adjust the clearance of brake shoe.
10. Install rear wheels and tires. Refer to WT-7, "Adjustment". G
Removal and Installation of Wheel Cylinder INFOID:0000000006152305

WARNING: H
Clean dust with a vacuum dust collector to minimize the hazard of air borne particles or other materi-
als.
CAUTION: I
• While removing brake shoes, do not depress brake pedal because wheel cylinder pistons will pop
out.
• It is not necessary to disconnect brake tube except for disassembly or replacement of wheel cylin-
J
der assembly.
• Keep drum free from brake fluid.
REMOVAL K
1. Remove the rear drum brake assembly. Refer to BR-40, "Removal and Installation of Drum Brake Assem-
bly".
2. Disconnect the brake tube from the wheel cylinder. L
NOTE:
Cap or plug opening(s) to prevent fluid from spilling.
3. Remove the wheel cylinder bolts, and then remove wheel cylinder from the back plate. M
INSTALLATION
Installation is in the reverse order of removal.
• Tighten bolts to the specified torque. Refer to BR-40, "Component". N
• Bleed the brake system. Refer to BR-11, "Bleeding Brake System".
Disassembly and Assembly of Wheel Cylinder INFOID:0000000006152306

O
WARNING:
Clean dust with a vacuum dust collector to minimize the hazard of air borne particles or other materi-
als. P
CAUTION:
• While removing brake shoes, do not depress brake pedal because wheel cylinder pistons will pop
out.
• It is not necessary to disconnect brake tube except for disassembly or replacement of wheel cylin-
der assembly.
• Keep drum free from brake fluid.
DISASSEMBLY

Revision: July 2010 BR-43 2011 Sentra

 REAR DRUM BRAKE
< SERVICE INFORMATION >
1. Remove the wheel cylinder. Refer to BR-43, "Removal and Installation of Wheel Cylinder".
2. Remove the boots from the ends of the wheel cylinder and dis-
card the boots.
CAUTION:
Do not reuse the boots.
3. Pull out the pistons from the wheel cylinder.
4. Remove piston cups from the piston and discard the piston
cups.
CAUTION:
Do not reuse the piston cups.

SFIA3077E

5. Remove the bleed valve and cap.

INSPECTION AFTER DISASSEMBLY
Check the pistons, spring, and inner wall of the cylinder for wear, corrosion, and damage. If malfunction is
detected, replace it.
ASSEMBLY
CAUTION:
Do not use NISSAN rubber grease (KRE00 00010, KRE00 00011) during assembly.
1. Install the bleed valve and cap, tighten to specification. Refer to BR-40, "Component".
2. Apply brake fluid to the piston sliding surface on the wheel cylinder.
3. Apply NISSAN rubber lubricant (KRE12 00030) to the piston
cups and boots. Assemble the spring, piston cups, and piston
inside the wheel cylinder as shown.
CAUTION:
When inserting the piston, be careful not to scratch the
wheel cylinder wall.
4. Install the boots on the wheel cylinder securing them in the
grooves as shown.

SFIA3078E

5. Install the wheel cylinder. Refer to BR-43, "Removal and Installation of Wheel Cylinder".

Revision: July 2010 BR-44 2011 Sentra

 SERVICE DATA AND SPECIFICATIONS (SDS)
< SERVICE INFORMATION >
SERVICE DATA AND SPECIFICATIONS (SDS)
A
General Specification INFOID:0000000006152307

Unit: mm (in) B
MR20DE QR25DE
Applied model
Base, S, SR, SL SE-R SE-R SPEC-V
Front disc brake Brake model CLZ25VB CLZ25VJ AD25V C
Cylinder bore diameter 57.2 (2.252) 57.2 (2.252) 57.15 (2.250)
Pad thickness 11 (0.433) 11 (0.433) 11 (0.433)
D
Rotor outer diameter ×
280 × 24.0 (11.02 × 0.945) 296 × 26.0 (11.65 × 1.024) 320 × 28.0 (12.60 × 1.102)
thickness
Rear disc brake Brake model — AD9A/DS17
E
Cylinder bore diameter — 34.93 (1.375)
Pad thickness — 8.5 (0.335)
Rotor outer diameter × BR
— 292 × 9.0 (11.50 × 0.354)
thickness
Rear drum brake Brake model LT23E — —
Cylinder bore diameter 19.05 (0.750) — — G
Lining 194.1 × 35 × 2.9
— —
Length × width × thickness (7.642 × 1.378 × 0.114)
Drum inner diameter 228.6 (9.000) — —
H

Master cylinder Cylinder bore diameter 23.81 (0.937)

Brake booster Booster model C255
I
Diaphragm diameter 255 (10.04)
Recommended brake fluid DOT 3
J

Revision: July 2010 BR-45 2011 Sentra

 SERVICE DATA AND SPECIFICATIONS (SDS)
< SERVICE INFORMATION >
Brake Pedal INFOID:0000000006152308

Unit: mm (in)

AWFIA0557ZZ

Brake pedal height (H)

164.0 - 174.0 (6.46 - 6.85)
(from dash lower panel top surface)
Brake pedal full stroke (S) 135.1 (5.32)
Clearance between pedal stopper bracket and threaded end of the stop
0.74 - 1.96 (0.0291 - 0.0772)
lamp switch (C1) and ASCD cancel switch (C2), if equipped.

Check Valve INFOID:0000000006152309

SFIA0210E

Vacuum leakage when connected to booster side (1)

Within 1.3 kPa (10 mmHg, 0.39 inHg) of vacuum for 15 seconds
[at vacuum of – 66.7 kPa (– 500 mmHg, – 19.69 inHg]
Vacuum leakage when connected to engine side (2)
No vacuum will be applied.

Revision: July 2010 BR-46 2011 Sentra

 SERVICE DATA AND SPECIFICATIONS (SDS)
< SERVICE INFORMATION >
Brake Booster INFOID:0000000006152310

SGIA0060E

Input rod installation standard length (B) 163.2 - 164.2 mm (6.43 - 6.46 in) E
Vacuum leakage
Within 1.3 kPa (10 mmHg, 0.39 inHg) of vacuum for 15 seconds
[at vacuum of – 66.7 kPa (– 500 mmHg, –19.69 inHg)]
BR
Front Disc Brake INFOID:0000000006152312

CLZ25VB
Unit: mm (in)
G

Standard thickness (new) 11 (0.433)

Brake pad
Repair limit thickness 2.0 (0.079) H
Standard thickness (new) 24.0 (0.945)
Repair limit thickness 22.0 (0.866)
Disc rotor Runout limit 0.035 (0.0014) I
Maximum uneven wear (mea-
0.02 (0.0008) or less
sured at 8 positions)
J
CLZ25VJ
Unit: mm (in)

Standard thickness (new) 11 (0.433)

Brake pad K
Repair limit thickness 2.0 (0.079)
Standard thickness (new) 26.0 (1.024)
Repair limit thickness 24.0 (0.945) L
Disc rotor Runout limit 0.035 (0.0014)
Maximum uneven wear (mea-
0.02 (0.0008) or less M
sured at 8 positions)

AD25V
Unit: mm (in)
N
Standard thickness (new) 11 (0.433)
Brake pad
Repair limit thickness 2.0 (0.079)
Standard thickness (new) 28.0 (1.102) O
Repair limit thickness 26.0 (1.024)
Disc rotor Runout limit 0.035 (0.0014)
Maximum uneven wear (mea- P
0.02 (0.0008) or less
sured at 8 positions)

Rear Disc Brake INFOID:0000000006152313

AD9A/DS17

Revision: July 2010 BR-47 2011 Sentra

 SERVICE DATA AND SPECIFICATIONS (SDS)
< SERVICE INFORMATION >
Unit: mm (in)

Standard thickness (new) 8.5 (0.335)

Brake pad
Repair limit thickness 2.0 (0.079)
Standard thickness (new) 9.0 (0.354)
Repair limit thickness 8.0 (0.315)
Disc rotor Runout limit 0.07 (0.0028)
Maximum uneven wear (mea-
0.015 (0.0006) or less
sured at 8 positions)

Rear Drum Brake INFOID:0000000006152314

LT23E
Unit: mm (in)
Standard thickness (new) 2.9 (0.114)
Brake lining
Repair limit thickness 1.5 (0.059)
Standard inner diameter (new) 228.6 (9.000)
Drum
Repair limit inner diameter 230.0 (9.055)

Revision: July 2010 BR-48 2011 Sentra