Scribd
Upload
145 views

Experiment 4 Series & Parallel Circuits Voltage Divider & Current Divider Rules

This document describes an experiment to study and verify the voltage and current divider rules in series and parallel circuits. Students are asked to build two circuits using resistors and a power supply, then measure voltages and currents throughout. They will use the results to determine whether combinations of resistors are in series or parallel and justify whether the voltage divider rule or current divider rule applies in each case. Questions probe their understanding of parallel and series configurations and how divider rules are manifested in the circuit measurements.

Uploaded by

Elking Delina
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
145 views

Experiment 4 Series & Parallel Circuits Voltage Divider & Current Divider Rules

This document describes an experiment to study and verify the voltage and current divider rules in series and parallel circuits. Students are asked to build two circuits using resistors and a power supply, then measure voltages and currents throughout. They will use the results to determine whether combinations of resistors are in series or parallel and justify whether the voltage divider rule or current divider rule applies in each case. Questions probe their understanding of parallel and series configurations and how divider rules are manifested in the circuit measurements.

Uploaded by

Elking Delina
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 7

Experiment 4

Series & Parallel Circuits


Voltage Divider & Current Divider Rules

Introduction

For a series circuit shown in Figure 1, the voltages across resistors R1, R2 and R3 can be
written as,

This is the voltage divider rule (VDR).

For a parallel circuit given in Fig. 5.2, the branch currents can be written in terms of the total
current as,

(2)

This is termed as the current divider rule (CDR).


Objectives
1. To study the voltage current relationships of series and parallel circuits
2. To verify the voltage current divider and voltage divider rules.

Materials
One dc power supply
One multimeter
Assorted resistors

Figure 3: Series-parallel circuit I Figure 4: Series-parallel circuit II

R2 = 100Q, R3 = 150Q, R4 = 220Q, R6 = 330Q

Procedure
Simulation
1. Build the circuit given in Figure 3 on Multisim software.
2. Connect voltmeters, ammeters (or multimeters) at appropriate positions to measure
voltages and currents shown in Table 1.
3. Disconnect the voltage source. Connect a mutimeter and measure the total resistance
and record the value in Table 1. (Remember resistance is always measured without
any source connected to the circuit)
4. Repeat steps 2 and 3 for the circuit given in Figure 4 and record the values in Table 2.
Table 1: Simulation results for Figure 3
Is I2 I3 I4 I5 I6 V2 V3 V4 V5 V6 Req

Table 2: Simulation results for Figure 4


Is I2 I3 I4 I5 I6 V2 V3 V4 V5 V6 Req

Questions

Refer to Figure 3 and the results obtained in Table 1 and answer the following questions:

1. Are R4 and R6 in parallel or in series? Why? Refer to voltage current


measurements for your answer to justify.

2. Are R3 and R4 in parallel or in series? Why? Justify

3. Are Vs and R3 in parallel or in series? Why? Justify

4. Are Vs and R6 in series or in parallel? Why? Justify.

5. Are Vs and Req. in parallel or in series? Why? Justify


6. Is VDR applicable for applicable R3 and R4? Why? Justify your answer on the
basis of theory given in the introduction.

7. Is CDR applicable for R4 and R6? Why? Justify your answer on the basis of theory
given in the introduction.

8. Is the parallel combination of R4 and R6 in series or in parallel with R2? Why?


Justify.

Refer to Figure 4 and the results obtained in Table 2 and answer the following questions:

9. Are R4 and R6 in parallel or in series? Why? Refer to voltage current


measurements for your answer to justify.

10. Are R3 and R4 in parallel or in series? Why? Justify

11. Are Vs and R3 in parallel or in series? Why? Justify

12. Are Vs and R6 in series or in parallel? Why? Justify.

13. Are Vs and Req. in parallel or in series? Why? Justify

14. Is VDR applicable for applicable R3 and R4? Why? Justify your answer on the
basis of theory given in the introduction.
15. Is CDR applicable for R4 and R6? Why? Justify your answer on the basis of theory
given in the introduction.

16. Is the parallel combination of R4 and R6 in series or in parallel with R2? Why?
Justify.

Any other observations or comments

5
7

You might also like