Part-I Q1 Only Short Answer Type Questions (Answer All-10) (2 X 10) A) B) C) D) E) F) G) H)
Part-I Q1 Only Short Answer Type Questions (Answer All-10) (2 X 10) A) B) C) D) E) F) G) H)
Registration No :
Part- I
Q1 Only Short Answer Type Questions (Answer All-10) (2 x 10)
a) Distinguish between lamina and laminate?
109 b) 109 109
What are three common modes of 109failure of a unidirectional
109 109
composite 109
subjected to 109
Longitudinal tensile load?
c) Give some biomedical application of composite.
d) What is a composite fiber? Give one example.
e) Name two composite structures subjected to (i) Creep and (ii) fatigue loading.
f) Mention the stiffness parameter on which the buckling load depends?
g) Draw the stress-strain diagram of the following fibers in the same plot (Carbon, Boron, E-
Glass).
109 h) A unidirectional109
109 composite is composed
109 of 65%109by volume of 109
carbon fibers (modulus
109 109
240GPa) in an epoxy resin matrix (modulus 4GPa). Calculate the longitudinal modulus of
composite.
i) Explain the situation where bottom pouring method is explained over lip pouring method.
j) Explain the term wettability related to MMcs.
Part- II
Q2 Only Focused-Short Answer Type Questions- (Answer Any Eight out of Twelve) (6 x 8)
109 a) Derive the equilibrium
109 109 equations109
for a laminated 109
composite plate109
subjected to transverse
109 109
loads.
b) Derive the stress–strain relationship for an orthotropic material.
c) Describe with a neat sketch of laminate stacking sequence code.
d) Discuss the interlaminar stresses and edge effects in a laminate.
e) State and explain Tsai-Hell theory of failure of a lamina.
f) Derive the law of mixture for stress and modulus of elasticity. State all assumptions used
for derivation.
109 g) Explain buckling109
109 of composite plates.
109 109 109 109 109
h) Explain the importance of measurement of void fraction in a composite.
i) Describe pulstrusion process stating its advantages and disadvantages with different
matrix material used in this process.
j) Distinguish between thermosetting plastics and thermo plastics.
k) Derive the governing differential equations for a symmetric cross ply laminated plate.
l) Compare the longitudinal and transverse stiffness of two composites with the same matrix
but different fibers. For the first case (Ef/Em)1=50 and for the second case (Ef/Em)2=25.
109 Assume poission’s
109 109 ratio =0.5. 109 109 109 109 109
Part-III
Only Long Answer Type Questions (Answer Any Two out of Four)
109 Q3 With a neat sketch,
109 109 describe a109Resin Transfer109
Moulding (RTM)109process and 109
filament (16) 109
welding process with its advantages, disadvantages and applications.
Q4 a) State the stress-strain behavior of different categories of elastic materials indicating the (10)
number of independent elastic constants for each.
b) Define interfacial strength of a composite material. Explain the procedure of testing (6)
interfacial strength of FRP composite.
109 Q5 Define
109 composite
109 with its characteristics?
109 How are
109 composites classified?
109 Briefly 109
explain (16) 109
each type of composites with their merits and demerits.
Q6 a) Determine the equivalent stress system along the material axis 1-2 for a lamina with ply (10)
angle 450 . Assume stress along reference axes x 200 GPa, y 50 GPa.
b) Distinguish between Longitudinal fibre strength and transverse fibre strength. (6)