Fosroc Renderoc SPXtra constructive solutions

Shrinkage controlled, polymer modified, cementitious

repair mortar, specifically designed for spraying Properties

Uses The following typical results were obtained at a water:powder

ratio of 0.18.
Renderoc SPXtra is suitable for wet or dry spraying and hand
application in a wide variety of repair applications, and is Test method Typical result
particularly well suited to vertical and overhead repairs. Typical Drying shrinkage to ASTM C 157-93
applications would include, but not be limited to, the following: 7 days : <300 microstrain
„ Mass infill to large areas 28 days : <500 microstrain
Permeability : <8 mm
„ Repairs to irregular profiles (DIN 1048 Part 5)
„ Excellent for repairs to fire-damaged concrete Flexural strength : >10 N/mm2 at 28 days
(BS 6319 Pt.3)
„ Fast track repair programmes, where rapid application at Tensile strength : >5 N/mm2 at 28 days
high volume is required (BS 6319 Pt.7)
„ Single layer, high build applications Compressive strength : >50 N/mm2 at 28 days
hand application
„ Can be used as a Cathodic Protection Overlay where the (BS 1881 Pt.1161) >60 N/mm2 at 28 days
resistivity required is lower than 20,000 Ohm-cm (iterative result, based upon
spray application)
Advantages Initial Surface
Renderoc SPXtra features Dimensional Stability Technology absorption (ISAT) : 0.04%
- a new materials technology which controls the rate of drying (BS 1881 Pt.208)
shrinkage such that, when used correctly : Electrical Resistivity : < 20,000 Ohm-cm

i. the dimensions of the repair remain stable; and thus Note 1: 100mm cubes, air cured @ 25°C.

ii. eliminating failure, due to shrinkage cracking. Design criteria

This in turn leads to a series of associated benefits : Dimensional Stability Technology is a major step forward in
the general compatibility of repair mortar systems with the
„ Cost effective - shrinkage control enables repairs to be
host concrete, and the control of shrinkage in particular.
completed ‘right first time’. Very low rebound is an
additional cost benefit Attention to the basic design criteria given below should
ensure that the full benefits of this technology are achieved :
„ Enhanced durability - works in tandem with extremely low
permeability to prolong effective working life (i) Recommended limits for a single spray application are:
„ Compatibility - aligns performance closer than ever before, Minimum applied thickness : 10 mm
to that of host concrete Overhead sections : up to 150 mm thick
Vertical sections : up to 200 mm thick
„ User friendly - specifically developed to provide an
Surface area of a single repair : see ‘Note’
easy-to-apply product, suitable for local conditions
NOTE : The restricting factor on surface area will be the
„ Definable performance - positive benefits are easily
practicality of maintaining a continuous
demonstrated via a single, simple measurement
application

Description ii) In situations where a substrate/repair barrier is required,

or enhanced bond strength/working time is required, or
Renderoc SPXtra is supplied as a ready to use blend of dry
where the substrate is likely to be damp (e.g. seawalls,
powders, which requires only the addition of clean water to
quays etc.), Nitobond EP epoxy bonding agent should be
produce a highly consistent, hand and spray grade, repair
used.
mortar suitable for most structural and load bearing repairs.
Renderoc SPXtra

(iii) Water addition - between 4.25 & 4.5 litres per 25 kg bag
Under no circumstances should part bags be used or
additional water be employed. Either of these two actions
will adversely affect material performance, automatically
invalidating Fosroc’s standard product guarantee.
Fosroc Renderoc SPXtra

Instructions for use Storage

Renderoc SPXtra should be mixed and applied in strict Shelf life

accordance with the Product Method Statement, a copy of
Renderoc SPXtra has a shelf life of 12 months if kept in a dry
which may be obtained from your nearest Fosroc office.
environment, in its original packing. If stored in conditions of
high temperature and/or humidity, the shelf life may be
Estimating
reduced to as little as 4 months.
Supply
Standards compliance
Renderoc SPXtra : 25 kg bags
Renderoc SPXtra repair mortar system complies with the
Yield
following international standards :
Renderoc SPXtra : approx 13.5 litres
ASTM C157-93 : Test for drying shrinkage
(at water addition of 4.25ltr/bag) per 25kg bag
DIN 1048 Part 5 : Test for permeability
BS 1881 Pt.208 : Initial surface absorption
Limitations

- Renderoc SPXtra should not be used when the ambient Precautions

temperature is below 5°C and falling.
Health and safety
- Renderoc SPXtra should not be part mixed, nor part bags
Renderoc SPXtra contains cement powders which, when mixed
used.
with water or upon becoming damp, release alkalis which can be
- Renderoc SPXtra should not be exposed to running water harmful to the skin.
either during application or prior to final set.
During use, avoid inhalation of the dust and contact with the skin or
eyes. Wear suitable protective clothing - eye protection, gloves and
respiratory equipment (particularly in confined spaces).

The use of barrier creams to provide additional skin protection is

also advised. In case of contact with the skin, rinse with plenty of
clean water, then cleanse thoroughly with soap and water.

In case of contact with eyes, rinse immediately with plenty of clean

water and seek medical advice. If swallowed seek medical attention
immediately - do not induce vomiting.

Fire

Renderoc SPXtra, is non-flammable and thus presents no

fire hazard.

For further information, please refer to the Product Material

Safety Data Sheet for Renderoc SPXtra.

* Denotes the trademark of Fosroc International Limited

†
See separate data sheet
Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for
the Supply of Goods and Service. All Fosroc datasheets are updated on a regular basis. It is the user’s responsibility to
obtain the latest version.

Head Office
telephone: (+9714) 2039699 fax: (+9714) 2859649 email: [email protected]
Al Gurg Fosroc LLC
Regional offices
Post Box 657, Dubai Abu Dhabi, Al Gurg Fosroc telephone: 673 1779 fax: 673 1449 email: [email protected]
United Arab Emirates Bahrain, YBA Kanoo telephone: 17738200 fax: 17732828 email: [email protected]
Kuwait, Boodai telephone: 4817618 fax: 4832124 email: [email protected]

www.fosroc.com
Oman, Al Amana telephone: 24815080 fax: 24817554 email: [email protected]
Qatar, Tadmur telephone: 4432365 fax: 4419517 email: [email protected]

UAE/0251/12/Q