High efficiency, IP55

three-phase cage induction motors

Frame size 63 to 315M

0.25 to 250 HP
IEC dimension

o m
. c
d o
n in
ek
t
rt a
e n
. c
ww
w

PT. Teco Multiguna Elektro

Office
Jl. Bandengan Utara No. 83/2-3, Jakarta 14440 - Indonesia
P.O.Box 4967 JKT 10049
Telp. : (62-21) 6622201, 6696985, 6615782, 6695024
Faks. : (62-21) 6697029, 6615783
e-mail : [email protected]

Branch Office
Jl. Berbek Industri II No. 21 Sidoarjo 60293
(Kawasan Rungkut Industri Surabaya)
Telp. : (62-31) 8431952, 8434224, 8417399 Faks.: (62-31) 8436672
e-mail : [email protected]

Representative Office
Kompleks Semarang Indah C-XII No. 5 Semarang Barat 50144
Telp. : (62-24) 7612310 Faks.: (62-24) 7612363
Certified ISO 9001 by
Factory
Jl. Mayor Oking Km. 2,7 - Gunung Putri, Citeureup 16961
Telp. : (62-21) 875-3401/3405, 8754982 Faks.: (62-21) 8752843
008
www.teco-indonesia.com Certificate No. 167861
Motor types AEEB and AEVB, Class F insulation, 380/ 415V - 50HZ

o m
. c
d o
n in
ek
t
rt a
e n
. c
ww
w

1
Motor types AEEB and AEVB, Class F insulation, 380/ 415V - 50HZ

o m
. c
d o
n in
ek
t
rt a
e n
. c
ww
w

1480 315MB 93.6 92.4 90.2 88.5 88.5 81.5 340 2190 311 2005 122 110 96 210 14.3 1070 1180

2
 o m
. c
d o
n in
ek
t
rt a
e n
. c
ww
w

3
 o m
. c
d o
n in
ek
t
rt a
e n
. c
ww
w

4
 o m
. c
d o
n in
ek
t
rt a
e n
. c
ww
w

5
 o m
. c
d o
n in
ek
t
rt a
e n
. c
ww
w

6
Standard Specification and Features

Type of motor Totally-enclosed fan-cooled squirrel cage induction motor

Design standards BS4999 , BS EN 60034 , IEC 60034, Starting Performance Design N
Voltages and frequency Standard stock available are 220-240/380-415 V / 50HZ for 3HP and below
380-415/660-720V/ 50HZ for 4HP and above
Other voltages such as 200V, 346V, 440V , 460V and 60HZ etc can be supplied on request.
Voltage variation Motors are suitable for operation for continuous operation (S1 duty) within +/- 6%
rated voltage.
Time duty Maximum continuous rating , S1 duty
Cooling method Self external fan, surface cooling ( IC 411 )
Method of starting Full voltage direct on line starting or star-delta starting
Mounting Horizontal foot mounting (IM 1001 or IM B3) , flange mounting (IM3011 or IM V1)
Stator insulation Non-hygroscopic class F insulation system, with class B temperature rise
and temperature rise (80 degree C rise) by resistance method at 1.0 S.F.
Rotor winding Squirrel cage, aluminium conductor with end-ring and wafter blades integrally cast.
Environmental conditions Place : Non-hazardous
Ambient temperature : -20 0C to 40 0C
Relative humidity : Less than 90% RH (non-condensation)
Altitude : Up to 1,000 metres above sea level.
Drive method
Direction of rotation

o m
Belt service, however 2 Pole & 4Pole 75HP and larger is for coupling drive
Standard motors are suitable for operation in either direction of rotation.

Test procedure
. c
Direction of rotation of motor can be reversed by interchanging any two of the power lines.
According to BS 4999
External fan

Fan cover o
The fan is of polypropylene and designed for bi-directional rotation.
Other material fan is available on request.

d
Pressed steel sheet.
Shaft
Bearing
in
Carbon steel , cylindrical single extension with keyway and key
Bracket mounting, grease pre-packed shielded ball bearings for frame size 63

n
through 180L, open bearings for frame size 180MA 2-Pole and 200L through 315M
Lubrication

k
Mineral oil, Li-base grease

e
( Frame size 63 through 250 use Multitemp SRL , frame size 280 and larger use

t
Shell Alvania R3)

rt a
Terminal box Standard terminal box is presssed steel type for motor frame size 180 and smaller,
cast iron T-box for frame size 200 and larger. Terminal box is rotatable in 90 degree
increments through 360 degrees.

n
Terminal box is on the right hand side as seen from drive end as standard. For footmounted
motors, it can be changed to the left hand side by changing the rotor position.
Painting

Nameplate
. c e Phenolic rust proof base plus lacquer surface finish painting in blue-grey colour
(Munsell 7.5BG 4/2)
Stainless steel

w
Grounding terminal All motors are provided with an internal grounding terminal in the motor main terminal box.
Additional external grounding terminal on the motor frame is provided for frame size

Eyebolt
Electromagnetic
compatibility
w w 280 and larger.
Motor of frame size 100 and larger is equipped with eyebolt or lifting lug.
Compliance with European Electromagnetic Compatibility (EMC) directive reference
number 89/336/EEC, standard EN 50081-1 1992, for motors up to 450KW
Options available : 1. IP56 , 2. Class H insulation , 3. Multi-speed 4. Anti-condensation heater ,
5. PTC thermistor for thermal protection , 6. Special paint finish 7. Corrosion proof
8. Special shaft extension, 9. Inverter duty application 10. Smoke spill duty
11. Grease relief valves for frames down to 100L

We supply a full range of general purpose induction motors, and also produce made-to-order
motors to answer special needs ranging up to 100.000 HP 13.8 kv

Featuring Other Products

l Single phase totally enclosed fan cooled induction motors l Frequency inverters
l Single phase open protected drip proof induction motors l Generating sets
l Three phase totally enclosed fan cooled induction motors l Gear reducers
l Three phase open protected drip proof induction motors l Electro-mechanics :
l Eddy current variable speed motors - Starters and contactors
l Brake motors, DC motors l Power transmissions :
l Slip ring wound rotor induction motors - Electro-magnetic cluthes/brakes
l Geared motors, Crane motors - Linear actuators
l Kiln use motors - Ball bearing screws
l Marine motors l Motors Beds & Rail
l Cooling tower motors l Contractor-Overload Relay
l Pole-change motors l MCCB - Soft Starter
l Clutch/brake motors l MMC Panel
l Vertical hollow shaft motors l LV & HV Distribution Panel
l High voltage motors l System Integrator
l High voltage synchronous motors
l Mills use induction motors
l Explosion proof motors UL Listed
l Increased safety motors
l Non-sparking motors
l High temperature resistant motors
l Inverter duty application motors
l Stepping motors