Design rules 0 Busbar calculation

Busbar calculation example

Here is a busbar calculation
to check.

Exercise data

# Consider a switchboard comprised of at least 5 MV cubicles.

Each cubicle has 3 insulators(1 per phase).
Busbars comprising 2 bars per phase, inter-connect the cubicles
electrically.

Bus b ar character is tics to check :

S : busbar cross-section (10 •1) 10 cm2

d : phase to phase distance 18 cm

l : distance between insulators 70 cm

on the same phase

θn : ambient température 40 °C

(θ - θn) : permissible temperature rise 50 °C

(90-40=50)

profile : flat

material : busbars in copper 1/4 hard, with a permissible

Cellule 1 Cellule 2 Cellule 3 Cellule 4 Cellule 5
strain η = 1 200 daN/cm2

arrangement: edge-mounted

number of busbar(s) per phase: 2

# The busbars must be able to withstand a rated current

d
Ir = 2,500 A on a permanent basis and a short-time withstand
d
current Ith = 31,500 A r m s . for a time of tk = 3 seconds.

# Rated frequency fr = 50 Hz

# Other characteristics:
1 cm 1 cm
5 parts in contact with the busbars can withstand a maximum
temperature of θmax = 100°C
10 cm
5 cm 5 the supports used have a bending resistance of F’ = 1 000 daN

12 cm

d d

TED300014EN_030_037. Gamme Schneider Electric

Design rules Busbar calculation
0

Let’s check
the thermal withstand
of the busbars! For the rated current (Ir)

The MELSON & BOTH equation allows us to define the

permissible current in the conductor:
0.61 0 .5 0 .39
· 24.9 ( θ – θ n ) S p
I = K -------------------------------------------------------------------
ρ20 [ 1 + α ( θ – 20 )]

with:
l : permissible current expressed in amperes (A)

θn : ambient temperature 40 °C

(θ - θn) : permissible temperature rise* 50 °C

S : busbar cross-section 10 cm2

p : busbar perimeter 22 cm
e
p20 : resistivity of the conductor at 20°C

cop p er: 1.83 µΩ cm

a

α : temperature coefficient
for the resistivity: 0.004

K : condition coefficient
e product of 6 coefficients (k1, k2, k3, k4, k5, k6),
described below
*(see table V in standard CEI 60 694 pages 22 and 23)

Definition of coefficients k1, 2, 3, 4, 5, 6:

# Coefficient k1 is a function of the number of bar strips

per phase for:
5 1 bar (k1 = 1)
5 2 or 3 bars, see table below:

e /a
0.05 0.06 0.08 0.10 0.12 0.14 0.16 0.18 0.20
number of bars per phase k1
2 1.63 1.73 1.76 1.80 1.83 1.85 1.87 1.89 1.91
3 2.40 2.45 2.50 2.55 2.60 2.63 2.65 2.68 2.70

In our case:
e/a = 0.1
number of bars per phase = 2
giving k1 = 1.80

Schneider Electric Gamme AMTED300014EN_030_03

 Design rules 0 Busbar calculation

# Coefficient k2 is a function of the surface condition of the bars:

5 bare: k2 = 1
5 painted: k2 = 1.15

# Coefficient k3 is a function of the busbar position:

5 edge-mounted busbars: k3 = 1
5 1 bar flat-mounted: k3 = 0.95
5 several flat-mounted bars: k3 = 0.75

# Coefficient k4 is a function of where the bars are installed:

5 calm indoor atmosphere: k4 = 1
5 calm outdoor atmosphere: k4 = 1.2
5 bars in non-ventilated ducting: k4 = 0.80

# Coefficient k5 is a function of the artificial ventilation:

5 without artificial ventilation: k5 = 1
5 cases with ventilation must be treated on a case by case
basis and then validated by testing.

# Coefficient k6 is a function of the type of current:

5 for alternatif current at a frequency of 60 Hz, k6 is a function of
the number of busbars n per phase and of their spacing.
The value of k6 for a spacing equal to the thickness of the
busbars:

n 1 2 3
k6 1 1 0.98

In our case:
n= 2 giving k6 = 1

In fact, we have:
k = 1.80 • 1 • 1 • 0.8 • 1 • 1 = 1.44

0 . 61 0.5 0 . 39
24 . 9 ( 90 – 40 ) • 10 • 22
I = 1. 44 • -----------------------------------------------------------------------------------------------------------------------------------------
1 . 83 [ 1 + 0 . 004 ( 90 – 20 ) ]

0 . 61 0.5 0 . 39
24 . 9 ( θ – θn ) •S •p
I = K • -------------------------------------------------------------------------------
ρ20 [ 1 + α ( θ – 20 ) ]

I= 2 689 A

The chosen solution: 2 busbars of 10 • 1 cm per phase

is appropriate:
Ir < I either 2 500 A < 2 689 A

TED300014EN_030_037. Gamme Schneider Electric

Design rules 0 Busbar calculation

For the short-time withstand current (Ith)

# we assume that, for the whole duration (3 seconds) :
5 all the heat given off is used to increase the temperature
of the conductor
5 the effect of radiation is negligible.

The equation below can be used to calculate the

temperature rise due to short-circuit:
0.24 • ρ 20 • I th 2 • t k
∆θ c c = -----------------------------------------------------------
-
(n • S ) • c • δ
2

with:
c : specific heat of the metal
cop p er: 0.091 kcal / daN°C

S : is the cross section expressed in cm2 10 cm2

n : number of bars per phase 2

Ith : is the short-time withstand current 31 500 A rms.
(rms. value of the maximum short-
circuit current)

tk : short-time withstand current

duration (1 to 3 secs) 3 in secs
δ : density of the metal
cop p er: 8.9 g/cm3
ρ20 : resistivity of the conductor at 20°C
cop p er: 1.83 µΩ cm

(θ - θn) : permissible temperature rise 50 °C

5 The temperature rise due to the short circuit is:

–6 2
0. 24 1.83 1.83 10 ² ( 3131 500500 )
∆θ c c = -----------------------------------------------------------------
3
2
-
( 22 /10
² 10 ) ² 00.091 .091 ² .9 8.9
Calculation of θt must be ∆θcc = 4 °C
looked at in more detail because the
required busbars have to withstand
Ir = 2 500 A at most
and not 2 689 A.
The temperature θt of the conductor after short-circuit will be:
θ t = θ n + ( θ – θ n ) + ∆θ cc
= 40 + 50 + 4
= 94 °C
for I = 2 689 A (see calculation in the previous pages)

Schneider Electric Gamme AMTED300014EN_030_03

 Design rules 0 Busbar calculation

# Let us fine tune the calculation for θt for I r = 2 500 A

( rated current for the busbars)

5 the M ELS ON & BOT H equation ( cf: page 31) , allows us to

deduce the following:
I = constant • (θ- θn) 0.61 et
Ir = cons tant • (∆θ) 0.61

therefore =I = (θ-θn)
( ) 0.61
Ir (∆θ)

2 689
2 500
= ( (∆ ) )
50
θ
0.61

1
50 =
∆θ
( 22 500
689
) 0.61

50 = 1.126
∆θ
∆θ = 44.3 °C

5 temperature θt of the conductor after short-circuit,

for a rated current Ir = 2 500 A is:
θt = θn + ∆θ + ∆θcc
= 40 + 44.3 + 4
= 88.3 °C for Ir = 2 500 A

The busbars chosen are suitable because:

θt = 88.3 °C is less than θmax = 100 °C

(θmax = maximum temperature that can be withstood by the parts in

contact with the busbars).

TED300014EN_030_037. Gamme Schneider Electric

Design rules 0 Busbar calculation

Let’s check
the electrodynamic
withstand of the busbars.
Forces between parallel-mounted conductors
Electrodynamic forces due to the short-circuit
current are given by the equation:

F1 = 2 l / ldyn2 / 10-8
d

(see drawing 1 at the start of the calculation example)

l : distance between insulators in the same phase 70 cm

d : phase to phase distance 18 cm

k : 2.5 for 50 Hz according to IEC

Idyn : peak value of short-circuit current

= k / lth


= 2.5 / 31 500
= 78 750 A

F1 = 2 / (70/18) / 78 7502 /10-8 = 482.3 daN



Forces at the head of the supports or busducts

Equation to calculate forces on a support :

F = F1 / H + h
H

with
F : force expressed in daN
H : insulator height 12 cm
h : distance from the head of the insulator
to the busbar centre of gravity 5 cm

Calculating a force if there are N supports

# The force F absorbed by each support is at most equal to
the force F1 that is calculated multiplied by a coefficient kn
which varies according to the total number N of equi-distant
supports that are installed.
5 number of supports ≥ 5 =N
5 we know N, let us define kn using the table below:

N 2 3 4 ≥5
kn 0.5 1.25 1.10 1,14

giving F = 683 (F1)/ 1.14 (kn) =


778 daN

The supports used have a bending resistance

F’ = 1 000 d a N calculated force F = 778 d aN.
The solution is OK

Schneider Electric Gamme AMTED300014EN_030_03

 Design rules 0 Busbar calculation

Mechanical strength of the busbars

Assuming that the ends of the bars are sealed, they are
subjected to a bending moment whose resultant strain is:
F1 • l v
η = ------------ • ---
12 I

with
η : is the resultant strain in daN/cm2

l : distance between insulators

in the same phase 70 cm

I/v : is the modulus of inertia of a busbar

or of a set of busbars 14.45 cm3
(value chosen in the table below)

η = 482.3 ² 70 1
------------------ ² -----------
12 14 .45

η = 195 d aN / cm 2

T he calculated resultant strain ( η = 195 d a N / cm 2 )

is less than the permissible strain for the copper busbars
1/4 hard ( 1200 d a N / cm 2) :

The solution is OK

Busbar dimensions (mm)

100 x 10
S cm2 10
Arrangement m Cu 0.089
daN/cm A5/L 0.027
x
I cm4 0,83
x’ I/v cm3 1.66
x
I cm4 83.33
x’ I/v cm3 16.66
x
I cm4 21.66
x’ I/v cm3 14.45
x
I cm4 166.66
x’ I/v cm3 33.33
x
I cm4 82.5
x’ I/v cm3 33
x
I cm4 250
x’ I/v cm3 50

TED300014EN_030_037. Gamme Schneider Electric

Design rules 0 Busbar calculation

Let us check
that the chosen busbars
do not resonate.
Inherent resonant frequency
The inherent resonant frequencies to avoid for busbars subjected to a
current at 50 Hz are frequencies of around 50 and 100 Hz.
This inherent resonant frequency is given by the equation:

E•I
f = 112 ------------4-
m•l

f : frequency of resonance in Hz

E : modulus of elasticity
for copper = 1.3 • 106 daN /cm 2

m : linear mass of the bar 0.089 daN/cm

l : length between 2 supports

or busducts 70 cm

I : moment of inertia of the busbar section

relative to the axis x’x perpendicular
to the vibrating plane 21.66 cm4
(choose m and l on the table on the previous page)

f = 112  -------------------------------
1 .3 ² 10 6 ² 21.66
 0. 089 ² 70 4 

f = 406 Hz

f is outside of the values that have to be avoided, in other words

42 to 58 Hz and 80 to 115 Hz:
The solution is OK

In conclusion

The busbars chosen, i.e. 2b a r s of 10 • 1 cm

p er p h a s e, a r e s u it a b le fo r a n Ir = 2 500 A a n d
I t h = 31.5 k A 3 s ec.

Schneider Electric Gamme AMTED300014EN_030_03