JOB SAFETY ANALYSIS

Location :
Job :
BASIC STEPS POTENTIAL PERSONAL / Existing Controls/ Available Safe Guards
ENVIRONMENTAL
HAZARD
Shifting of Material & Equipment.
Marching of man lift
With out load Hiting with other vehicle on
Providing Competent Operator along with signal man with valid licence.
road

Body injury temporary /

permanent / fatal

Shifting of material
Hiting with other vehicle on
with Pick-up, Hydra, Providing competent operator along with helper & properly tieup all equipments.
road.
Trailer

Falling of object To provide proper tie of material on pick-up.

Height work
Climbing to elevated Fall of person to lower level 1.   Suitable ladder & man lift use
platform
2.   Anchoring the ladder
3.   One person hold the portable ladder
4.   Full body safety belt with double lanyards is used for alternate hooking

5.   Daily tool box talk to the workers along with their job supervisor before issuing
height permit.
6.   Permit to work system.
Being struck against an object 1.   Daily tool box talk to the workers along with their job supervisor before issuing
height permit.
2.   Regular house keeping before and after the job.
Being struck by a dropped 3.   Lifting of materials, tools, tackles using suitable mechanical arrangement.
object
4.   Avoid more than one job at same vertical height.

Working at height Falls of person to lower level 1.   Full body safety belt with double lanyards is used

2. Daily tool box talk to the workers along with their job supervisor before issuing
start the job.
3.   Permit to work system followed.
4.   Access ladder to be followed.
5.   Life line fixing point to be checked.
Fall of material from height 1.   Safety helmet used with chin strap.

2.   Barricading with man wacher displayed at site.

3.   Daily tool box talk to the workers along with their job supervisor before issuing
height permit.
4.   No Loose material at height.
Use of portable Using a damaged ladder 1.Examination of ladder before use
ladder
2.Discard defective ladders
3. Training all workers before start the job.
Use of portable
ladder

Hit another object when moving 1.Assistance for lift

a ladder(equipment, personnel,
electrical) 2. Awareness of surroundings
Falls to lower level during 1.   Inspecting ladder before use
working from a portable ladder
2.   Proper anchoring of the ladder.
3.   People do not reach beyond the normal work zone
4.       Safety belt is used.
Being struck by dropped object 1.safety helmet
while carrying or working with
tools on a ladder

Lifting of materials Fall of material 1.   Correct selection and use of appropriate equipment

2.   Use of equipment which is maintained in good condition

3.   Tested and certified lifting machines and tools-tackles are used.
4.   Visual checking of lifting machines and tools-tackles before use.
5.   Lifting hook attached to the equipment to be lifted is checked.
6.   Weight of the material is confirmed from the tag or document of the material and
lifting arrangement is made accordingly.
7.   Lifting arrangement is made considering at least two-times safety factor.

8.   Lifting job is under permit to work system.

9.   Toolbox talk is conducted before start of the job.
10.        Trained personnel for the job
Overturning of hydra/crane 1.   Certified and skilled hydra/crane operator.

2.   Loadtested and certified hydra/crane is used.

3.   Ensured secured base

4.   Weight of the equipment is checked before lifting.

5.   Signaler available to guide the hydra/crane operator.

Impact due to backward 1.   Ensured the back horn and backlight available at the hydra/crane.
movement of hydra/crane
2.   Certified and skilled hydra/crane operator.
3.   Signaler available to guide the hydra/crane operator.
Striking of moving object 1.   Workers engaged .
2.   Escorted with rigger.
3.   Guide rope used for material movement.
4.   Clear access for material movement.

Welding
Welding 1. Welding face shield, leather gloves, apron, hand sleep, leg guard and safety shoe
are used.
2. Exhaust ventilation provided if required.

Exposure to radiation and light Welding face shield is used.

Electrocution 1. VRD ,ELCB instaled 2.

Use leather gloves 3.
ensure no joint poling.

Fire 1.   Work Permit

 Fire
2.   No solvent within 11 m radius
3.   Area is checked with gas detector to measure LEL.
4.   Fire blanket is used to confine hot sparks.
5.   Fire fighting training to the worker.
7.   One stand by person for emergency
8.   Job supervision to be ensured.

Gas Cutting
Gas cutting Emission of gases/fumes 1. Generally cutting is done in open area.

2. Exhaust ventilation provided if required.

Fire /Explosion 1. Fire extinguisher is provided in.

Used Flash back arrester both site.

2. Competent worker is employed.

4. Safety training to the worker and their supervisors.
5. Gas cylinder is kept far away from the cutting point.
Burn due to spatters 1. Face shield/cutting goggles, leather gloves and safety shoe are used.

Grinding
Grinding 1.Wheel guard provided
2. Wheel is replaced on notice of crack
3. Periodic checking of grinding wheel
4. Hot work permit is taken for grinding
Fire due to flying hot particles 1. Hot work permit is taken

2. Ensured no solvent within 11m radius

3. Effective enclosure
4. Fire fighting arrangement is available near the job.
5. Regular fire fighting training to the workers.
Flying particles impact 1.Safety goggles/face shield, Helmet, Gloves
Exposure to live wire 1.   Electrical connection is done by the licensed electrician
2.   MCB with proper rating is available to the supply line.

Checked By:
Name:
Designation:
Signature and Date:
 Date : 12/18/2020

Controls added to Reduce Risk/Additional REMARKS

Safe Guards Required

speed limit up to 10km/hr

speed limit up to 20km/hr

1.   Ladder to be checked before use and follow rule at

climb.

2.   Daily safety training required for workers,

supervisors .

3. Emergency cont-no to be displayed at site.

Fire - xxxxx
Ambulance - xxxxx

1.   Worker to be dedicated for housekeeping daily at

project area.
2. work permit displayed at site.
3.Tools tacklss TC attached xerox copy on site .

4. Height pass and Health Issued to ensure at starting

the job.
5.   Daily safety training required for workers,
supervisors .
1. Proper job supervision as well as safety.

2.   Daily safety training required for workers,

supervisors .

1.   Two jobs at same vertical line should not be

allowed.
2.   Daily safety training required for workers,
supervisors ..

3.   Worker to be dedicated for housekeeping daily at

project area.

1.   Defective ladders to be tagged and discarded.

2.   Testing procedure to be adopted.

Not applicable

Ladder safety training required.

1.rope to be used to lift object

2. Ladder safety training required.
3. Tool holders on ladder and on worker’s belt
1.   Regular lubrication of chain block, slings is
required.

1.   Contractor to be instructed to use loadtested and

certified hydra/crane.
2.   Certifed operator license for nontransport lifting
vehicles.
3. Area should be barigation.
4. stopage bar should be keep out of
barigation area for clear communication system .

Not applicable

1.   No person except the operator will be on the

hydra/manlift.

1. Exhaust blower required during hot work inside the

reactor /tank.
2. Awareness training required.
Welding apron to be provided to the welder.
1.   Welding apron to be provided.
2.   Welding glass to be checked before use.
Welding apron to be provided.
1.ELCB & VRD instaled with menten the value.
2. Cable joint is to b avoided.
3.Armour cable to be used
1.   Job earthing to be provided with cable both
side.
1.   Job earthing to be provided with cable both
side.

2.   No hot job below running solvent line

1. Exhaust blower required during hot work inside the

reactor /tank.
2. Awareness training required.
1.   Leakage in the cutting system is to be checked
regularly.
2.   Cylinder to be kept at cool place or under shed

3.   Cutting nozzle to be checked regularly.

Leather apron is to be provided.

Fire blanket kept on work site.

1.   Grinding machine is to be checked regularly.

2.   Standard grinding wheel to be used.

1.   No hot work to be done below the solvent transfer

line.
2.   Axix of grinding wheel to be checked.

Not Applicable
1.   Put off power when not in use.
2. Pressure gauge to be checked regul;arly.

Approved By:
Name: