Scribd
Upload
65 views

LibreRouter Specifications v7.5

The LibreRouter LR1 is an open-source hardware WiFi router with 3 radios (2.5GHz, 5GHz, 5GHz) and 2 Ethernet ports. It uses the LibreMesh firmware and has a weatherproof enclosure. Key specifications include 128MB RAM, 16MB flash memory, 4x5GHz antenna connectors, integrated 2.4GHz antennas, and power over Ethernet support with passive PoE. It is designed for outdoor mesh networking with a temperature range of 0-40°C.

Uploaded by

HECTOR
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
65 views

LibreRouter Specifications v7.5

The LibreRouter LR1 is an open-source hardware WiFi router with 3 radios (2.5GHz, 5GHz, 5GHz) and 2 Ethernet ports. It uses the LibreMesh firmware and has a weatherproof enclosure. Key specifications include 128MB RAM, 16MB flash memory, 4x5GHz antenna connectors, integrated 2.4GHz antennas, and power over Ethernet support with passive PoE. It is designed for outdoor mesh networking with a temperature range of 0-40°C.

Uploaded by

HECTOR
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

General Information

Brand LibreRouter
Model LR1

Hardware Specification
Configuration Triple-radio 2x2 802.11n Mesh Node
Design License Open-source Hardware
Firmware LibreMesh (based on OpenWrt 18.06.1)
Main chip MCU: Atheros QCA9558
RF: QCA9558 2T2R
GE PHY: QCA8337N (10/100/1000)
RF Radio 1: 2.4G 802.11b/g/n + LNA + PA, 2T2R (QCA9558)
Radio 2: 5G 802.11a/n + LNA + PA, 2T2R (AR9582 mPCI)
Radio 3: 5G 802.11a/n + LNA + PA, 2T2R (AR9582 mPCI)
Memory 128MB RAM DDR2
Flash 16MB NOR Flash
Hardware Watchdog ATTiny13 available via GPIO
Physical Interface 2 x Gigabit Ethernet RJ-45
2 x Gigabit Ethernet ports available (internal)
1 x USB 2.0 connector
1 x USB 2.0 connector (internal, inside enclosure)
1 x serial console 3.3V 115200 8N1 (internal header on the board)
1 x push button (reset)
1 x 2.4 RF Tx header (2.4GHz Ant_A, 2.4GHz Ant_B, GND)
1 x GPIO pin header
8 x Status LEDs, software controllable through GPIO

Radio Specification
Radio 1
Frequency Band 802.11b/g/n 2412-2472 MHz
Supported Data Rate 802.11b: 1, 2, 5.5, 11 Mbps
802.11g: 6, 9, 12, 18, 24, 36, 48, 54 Mbps
802.11n: 6.5 Mbps - 130 Mbps (20MHz), 13.5 - 300 Mbps (40MHz)
RF Shield Included, to block cross-interference with other radios
19 dBm +- 2 dBm Real power depends on country regulations (wireless-regdb)
Max Output Power
Measured at channel 11
Sensitivity -86dBm +- 2dBm One chain at channel 11 at 6mbps
Radio 2
Frequency Band 802.11a/n 5150-5875 MHz
Supported Data Rate 802.11a: 6, 9, 12, 18, 24, 36, 48, 54 Mbps
802.11n: 6.5 Mbps - 130 Mbps (20MHz), 13.5 - 300 Mbps (40MHz)
RF Shield Included, to block cross-interference with other radios
27 dBm +- 2 dBm Real power depends on the country according to the regulations
Max Output Power
Measured at channel 48
Sensitivity -83dBm +- 2dBm One chain at channel 48 at 6mbps
Radio 3
Frequency Band 802.11a/n 5150-5875 MHz
Supported Data Rate 802.11a: 6, 9, 12, 18, 24, 36, 48, 54 Mbps
802.11n: 6.5 Mbps - 130 Mbps (20MHz), 13.5 - 300 Mbps (40MHz)
RF Shield Included, to block cross-interference with other radios
27 dBm +- 2 dBm Real power depends on the country according to the regulations
Max Output Power
Measured at channel 48
Sensitivity -83dBm +- 2dBm One chain at channel 48 at 6mbps

LibreRouter LR1 librerouter.org


Antenna
Connectors 4 x external antenna connectors (RP-SMA female) for 5GHz
2 x internal UFL antenna connectors for 2.4Ghz
Pigtails 4 x pigtails for 5ghz, 1m long each, SMA male to RP-SMA male connectors
2.4ghz 1 x antenna MIMO 2x2, 14dB gain, integrated inside enclosure
5ghz 2 x antenna MIMO 2x2, 15dB gain, 10x28cm, weatherproof casing, SMA female

Power
Input PoE: 12v ~ 32v Passive PoE. 2-Pairs powering pins 4, 5 (+) and pins 7, 8 (-)
Standard DC Power Jack 2.1mm (internal diam) 5.5mm (external diam): 9v ~ 32v
PoE passthrough Software controllable, over 2nd Ethernet port, supporting up to 16W consumption
Earthing / Grounding Screw for earth cable
Power consumption Idle: three radios on + 1 GETH 4.5W
Typical: all radios in moderate use + 1 GETH 5-8W
Max: all radios in full use + full CPU + 2x GETH 14W
Max + PoE passthrough 30W

Environment & Mechanical


Temperature Range Operating: 0°C~40°C
Storage: -40°C to 70°C
Humidity 5%~90% typical
Dimensions Enclosure: 300 mm x 205 mm x 76 mm
Weight Main device 0.85kg, 5GHz antennas 0.38kg each, 0.05 each pigtail. 1.8kg total

Reliability
ESD Conductive: 4kV; Air: 8kV
Surge protection 8 x gas discharge arrestors, four per Ethernet port
MTBF Over 20000hrs

Compliance Standard
IC Argentina Wireless homologation (ENACOM)

Package content
Contents 1 x Device
Power adapter None
Enclosure CPE-75 Weatherproof box with integrated 2.4ghz antenna
Pigtails 4
External antennas 2 x antennas 5ghz MIMO 2x2

LED Indicators
LEDs 1 x Power
1 x System status
1 x USB
3 x WiFi activity (one for each radio)
2 x Ethernet activity (one for each port)

LibreRouter LR1 librerouter.org

You might also like