EE6603 : POWER SYSTEM OPERATION AND CONTROL

REGULATION - 2013

UNIT I: INTRODUCTION

PART A:

1. Define spinning reserve.

2. What is meant by load frequency control?
3. What are the advantages of pool operation with respect to LFC?
4. What is the use of secondary loop in ALFC system?
5. Define connected load?
6. What is the role of computers in the operation and control of power system?
7. What is load curve?
8. What is base load?
9. Define load factor.
10. What is the need for load forecasting?
11. What is the need for voltage regulation in power systems?
12. List the advantages of multi area operation.
13. Define diversity factor.
14. What is the effect of load factor on the cost of generation?
15. Define the term average load.
16. What is system level control
17. What are the effects of variable load in power system
18. What is the objective of power system control
19. What is the necessity of frequency regulation in power system.
20. What is the difference between load curve and load duration curve.
21. What are the different types of load
22. What is the significance of load factor and diversity factor.
23. Define load.

PART B:

1. i) Define the following: (1) Hot reserve (2) Cold reserve (3) diversity factor ii)A
generating station has the following daily load cycle:
Time in (hrs) 0-6 6-10 10-12 12-16 16-20 20-24
Load(MW) 20 25 30 25 35 20
Draw the load curve and calculate maximum demand, units generated per day, average
load, load factor.
2. Explain the following: (i) Load forecasting (ii) Economic dispatch control.
3. (i) Explain the following terms: Installed reserve, spinning reserve, cold reserve, hot
reserve.
(ii)A power station has to meet the following demand:
Group A:200KW between 8 A.M and 6 P.M
Group B:100KW between 6 A.M and 10 A.M
 Group C:50KW between 6 A.M and 10 A.M
Group D:100KW between 10 A.M and 6 P.M and then between 6 P.M and 6 A.M. Plot
the daily load curve and determine diversity factor, units generated per day and load
factor.
4. (i)Discuss about the recent trends in real time control of power systems.
(ii) Write short notes on load forecasting.
5. i)What is meant by chronological load curve? Give the information obtained from
load curves.
ii)Explain the advantages and different types of computer control system.
6. Describe briefly about plant level and system level control.
7. i) what are the information obtained from load curve and load duration curve?
ii) Briefly describe the importance of load forecasting and explain the method of
least square fit forecasting the base load.
8. What are objectives of modern trend in real time control of power system? Explain the
significant features of computer control in power system.
9. i) with neat sketch describe the p-f and Q-V control structure.
ii) Explain the following terms
i. Maximum Demand
ii. Plant use factor
iii. Plant capacity factor
iv. Reserve capacity
10. (i) Explain the need for voltage and frequency regulation in power system
(ii) A generating station has maximum demand of 400 MW. The annual load factor is
65% and capacity factor is 50% find the reserve capacity of the plant.
11. Draw load curve and load duration curve. Explain the importance of these curves in
connection with economic operation of power system
12. A generating station has maximum demand of 20 MW, load factor is 60% and capacity
factor is 50% find the reserve capacity of the plant, daily energy produced, maximum
energy that could be produced daily if the plant were running all the time and maximum
energy that could be produced if the plant when running(acc. To operating schedule)
were fully loaded.
13. A generating station has a maximum demand of 50,000 KW.calculate the cost per unit
generated from the following data.
6
Capital Cost = Rs95 x 10
Annual load factor = 40%
6
Annual cost of fuel and oil = Rs9 x 10
6
Taxes, wages and salaries etc.= Rs7.5 x 10
Interest and depreciation = 12%
 UNIT II: REAL POWER- FREQUENCY CONTROL

PART A:

1. State the advantages of state variable model.

2. What is AGC?
3. What are the conditions necessary for sharing load operating in parallel between the
two synchronous machines?
4. Define area control error.
5. What are the classification of system load?
6. What is meant by load frequency control.
7. Why the frequency and voltage to be regulated in a power system?
8. Compare the functions of “speed Governor” and “ speed changer” in a speed
governing systems of a turbine generator set.
9. What do you understand by coherent group of generators?
10. A speed governor system cannot completely eliminate frequency error caused by a
step load change in power system. Justify this statement.
11. How is the real power in power system controlled?
12. What is meant by free governor operation?
13. What is the function of load frequency control on a power system?
14. Define speed droop.
15. Draw the dynamic responses of change in frequency for a step load change for single
area system
16. What is the use of secondary loop in ALFC system?
17. What is meant AFRC
18. State whether changes in AVR loop will be reflected in ALFC loop.
19. List the advantages of multi area operation.
20. Explain the principle of tie line bias control.

PART B:

1. Two synchronous generators operating in parallel. Their capacities are 300MW and
400MW. The droop characteristics of their governors are 4% and 5% from no load to full
load. Assuming that the generators are operating at 50HZ at no load , how would be a
load of 600MW shared between them. What will be the system frequency at this load?
Assume free governor action.
2. Develop the state variable model of a two area system and state the advantages of the
model.
3. Draw the block diagram of uncontrolled two area load frequency control system and
explain the salient features under static condition.
4. How is speed governor mechanism modeled? Explain its operations with the speed load
characteristics.
5. Derive the transfer function model and draw the block diagram for single control area
provided with governor system. From the transfer function derive the expression for
steady state frequency error for a step load change.
6. What are the components of speed governor system of an alternator? Derive its transfer
function with an aid of a block diagram.
7. Explain the dynamic response of single area load frequency control.
8. Two 1000KW alternators operate in parallel. The speed regulation of first alternator is
100% to 103% from full load to no load and that of other 100% to 105%. How will the
two alternators share load of 1200KW and at what will one machine cease to supply any
portion of the load.
9. For a system regulation =4Hz/p.u.MW,Kp=150 Tp=18sec,ΔP0=0.01p.u.Find the dynamic
response of uncontrolled case. Also derive the equation used.
10. Derive the expression for steady state frequency change for single area system with the
following cases.
(i)Changes in load with fixed speed
(ii)changes in speed with fixed demand
11. i) Determine the primary ALFC loop parameters for a control area having the
following data.
Total rated area capacity Pr=2000MW.
Normal operating load Pd=1000MW.
Inertia constant H=5.0
Regulation R=2.40 Hz/pu MW (all area generators)
We shall assume that the load frequency dependency as linear meaning that the old load
would increase 1% for 1% frequency increase.
ii) Highly brief the importance of regulating frequency and voltage of the power
system.
12. Explain the static and dynamic characteristics of single area control system.
 Unit-III
REACTIVE POWER–VOLTAGE CONTROL

Part-A

1. What are the merits and demerits of synchronous compensator?

2. What are the various methods of voltage control in transmission system?
3. What are the various functions of excitation system?
4. Show the voltage control and reactive power control are interrelated.
5. Give the function of AVR.
6. State difference between P-f and Q-V controls.
7. What are the methods to improve the voltage profile in the power system.
8. What is the need for the compensator in the AVR loop.
9. What is meant by stability compensation?
10. Draw the root loci for zero compensated loops.
11. Compare shunt and series capacitor.
12. Discuss the effect of compensation on the maximum power transfer in a transmission line.
13. What is SVC? Why is it used.
14. Draw the phasor diagram of SVC.
15. How is voltage control obtained by using tap changing transformer/
16. What are the methods of voltage control/
17. What are the different types of SVC/
18. What is booster transformer? Where is it used?

Part-B

1. Describe various methods of voltage control and explain any three in detail.
2. Draw the diagram of a typical automatic voltage regulator and develop its block
diagram representation.
3. (i) Name the generators and consumers of reactive power in a power system.
(ii) What are static VAR compensators? State the advantages of SVS.
4. Explain the following methods of voltage control (i) Tap changing transformers (ii) Shunt
reactors (iii) Synchronous phase modifiers (iv) Shunt capacitors (v) series capacitors.
5. Draw the circuit for a typical excitation system and derive the transfer function
model and draw the block diagram.
6. What are the different methods of voltage control? Explain any two methods in detail.
7. (i) Develop a typical excitation arrangement to control the voltage of an alternative and
explain.
(ii) Briefly explain the role of tap changing transformer in voltage control?
8. What is Static VAR compensator? Where is it used? Explain its operation. Also state the
merits of static VAR compensator over the other methods of voltage control.
9. (i)Discuss in brief about generation and absorption of reactive power.
(ii) Derive the relations between voltage, power and reactive power at a node
for applications in power system control.
10. Describe the various methods of reactive power control and explain any two in detail.
11. Discuss static and dynamic analysis of AVR.
 Unit-IV
UNIT COMMITMENT AND ECONOMIC DISPATCH
Part-A
1. What is meant by FLAC?
2. Write the condition for the optimal power dispatch in a lossless system.
3. Draw the incremental fuel cost curve.
4. What is meant by spinning reserve?
5. Write the significance of Unit Commitment.
6. Draw the incremental cost curve of a thermal power plant.
7. Write the equality and inequality constraints considered in the economic dispatch
problem.
8. Define spinning reserve constraint in unit commitment problem.
9. What is incremental cost criterion?
10. What is minimum up and minimum down time in unit commitment problem?
11. Define participation factor.
12. What is participation factor with respect to economic load dispatch
13. Write the co-ordination equation taking losses into account.
14. What is meant by incremental cost curve?
15. Compare with unit commitment and Economic load dispatch
16. Define penalty factor
17. List the few constraints that are accounted in unit commitment problem
18. What is meant by priority list method
19. Mention the assumption made in the formation of loss formula matrix B.
20. What are the advantages of using forward dynamic programming method
21. State unit commitment problem.
22. Define incremental efficiency
23. What is difference between load frequency controller and economic dispatch controller

Part-B

1. State the unit commitment problem. With the help of a flow chart, explain
forward dynamic programming solution method of unit commitment problem.
2. The fuel inputs per hour of plants 1 and 2 are given
2
as F1= 0.2P1 +40P1+120Rs/hr
2
F2=0.25P2 +30P2+150Rs/hr
Determine the economic operating schedule and the corresponding cost of
generation. The maximum and the minimum loading on each unit are 100MW
and 25MW. Assume the transmission losses are ignored and the total demand is
 180MW. Also determine the saving obtained if the load is equally shared by both the
units.
3. (i) With the help of Flow chart explain Economic dispatch by λ Iteration method
without loss.
(ii) The fuel cost of two units are given by
2
F1=F1 (PG1) = 1.5+20PG1+0.1PG1 Rs\hr
2
F2=F2 (PG2) = 1.9+30PG2+0.1PG2 Rs\hr
If the total demand on the generator is 200 MW. Find the economic load
scheduling of the two units.
(iii) What is the significance of equality and inequality constraints in the formulation of
optimum dispatch problem?
4. (i) What is unit commitment problem? Discuss the constraints that are to be accounted
in unit commitment problem.
(ii) Obtain the priority list of unit commitment using full load average production cost
for the given data:
2
Heat rate of unit1 H1= 510+7.2PG1+0.00142 PG1 MW\hr Heat
2
rate of unit2 H2= 310+7.85PG2+0.00194PG2 MW\hr
2
Heat rate of unit3 H3= 78+7.97PG3+0.00482PG3 MW\hr. PD=500MW
Unit Mm(MW) Max(MW) Fuel Cost (K)
1 150 600 1.1
2 100 400 1.0
3 50 200 1.2

5. (i) Explain the unit commitment problem using priority ordering load dispatch.
(ii) Explain the term ‘Incremental Operating Cost’ of power system related with
economic dispatch.
6. The fuel inputs per hour of plants 1 and 2 are given as F 1=
2
0.2P1 +40P1+120 Rs/hr
2
F2=0.25P2 +30P2+150Rs/hr
Determine the economic operating schedule and the corresponding cost of generation if
the maximum and minimum loading on each unit is 100MW and 25MW.Assume the
transmission losses are ignored and the total demand is 180 MW. Also determine the
saving obtained if the load is equally shared by both the units.
7. Explain various constraints in UC and indicate the steps involved in solving UC by DP
method.
8. Formulate the coordination equations with losses neglected and also explain the
algorithmic steps of iterative method to find the solution of coordination equations.
9. (i)Explain the priority list method of solving unit commitment Problem. State merits
and limitations of this method.
10. The fuel cost functions for three thermal plants in $/h are given
 by
2
F1=0.004Pg1 +5.3Pg1+500
2
F2=0.006Pg2 +5.5Pg2+400
2
F3 =0.009Pg3 +5.8Pg3+200 where Pg1,P g2,Pg3 are in MW. Find the optimal
dispatch and the total cost when the total load is 925 MW with the following
generator limits. 100MW≤Pg1≤450MW, 100MW≤Pg2≤350MW,
100MW≤Pg3≤225MW

11. (i)Explain the forward dynamic programming method of solving unit commitment
problem.
(ii)Develop an iterative algorithm for solving the optimum dispatch equation of an
'n' bus power system taking into account the effects of system losses.
12. (i)Construct the priority list for the units given below.
2
H1=510+7.20P1+0.00142P1 .Pmin=150MW.Pmax=600MW.
Fuel cost=1.1Rs/MBtu.
2
H2=310+7.85P2+0.00194P2 .Pmin=100MW.Pmax=400MW.
Fuel cost=1.0Rs/MBtu
2
H3=78+7.97P3+0.00482P3 .Pmin=50MW.Pmax=200MW.
Fuel cost=1.2Rs/MBtu
ii)Derive the co ordination equation with losses neglected.

13. (i) The cost characteristics of three plants of a system are

2
C1=0.05P1 +17.0P1+160 Rs/hour
2
C2=0.06P2 +14.4P2+200 Rs/hour
2
C3=0.08P3 +9.0P3+240 Rs/hour Where P1,P2,P3 are in MW.
The incremental transmission losses for the network with respect to plants 1,2 and 3
are 0.05,0.10 and 0.15 MW per MW of generation. Find the optimal dispatch for a
total load of 100MW and also its incremental cost of received power.
ii) The input output curve characteristics of three units are
2
F1=750+6.49Pg1+0.0035Pg1 .
2
F2=870+5.75Pg2+0.0015Pg2 .
2
F3=620+8.56Pg3 +0.001Pg3 . The fuel cost of unit 1 is 1.0 Rs/MBtu, 1.0
Rs/MBtu for unit 2 and 1.0 Rs/MBtu for unit 3. Total load is 800MW. Use the
participation factor method to calculate the dispatch for a load is increased to
880MW?

14. With a neat flow chart explain the iterative algorithm for solving the economic
dispatch equation of N bus power system taking into account the effects of
system losses.
15. The fuel-cost functions for three thermal plants are given by
2
F1=0.004Pg1 +5.3Pg1+500 $/hr
2
F2=0.006Pg2 +5.5Pg2+400 $/hr
 2
F3=0.009Pg3 +5.8Pg3+200$/hr
Where P g1,Pg2and Pg3 are in MW.Find the optimum scheduling and the total cost
per hour for a total load of 975 MW with the following generator limits.
100MW≤Pg1≤450MW
100MW Pg2 350MW
100MW≤Pg3≤225MW

16. In power system having two units, the loss co-efficient are
-1 -1
B11=0.0015MW , B12=-0.0006MW
-1 -1
B21=0.0006MW ,B22=0.0024MW
The incremental production costs of the units
are =0.08PG1+20 Rs/MWhr
=0.09PG2+16Rs/MWhr
Find the generation schedule for λ=20 and 25. Find also change in
transmission loss between two schedules.
17. Explain the Forward Dynamic Programming method of solving unit commitment problem
with neat flow chart.
(ii) Explain briefly various constraints on unit commitment problem.

18. The input output curve characteristics of three units are

2
F1=940+5.46PG1+0.0016PG1
2
F2=820+5.35PG2+0.0019PG2
2
F3=99+5.65PG3+0.0032PG3 . Total load 600MW. Use the participating factor method to
calculate dispatch for a load is reduced to 550MW
 Unit-V
COMPUTER CONTROL OF POWER SYSTEMS
Part-A
1. What are the functions of SCADA?
2. Define state estimation.
3. What is “SCADA”?
4. Write any two functions of Load Dispatch Center.
5. Define the EMS system.
6. Define network topology in power system.
7. What are the different operating states in power system.
8. Distinguish between reliability and security of power system.
9. What are the EMS functions?
10. List out the conditions for normal operations of a power system.
11. What do you understand by security constraints?
12. What is contingency analysis program
13. List the factors that affects the power system security
14. What are the typical sensors used in power system application
15. When is power system considered to be secured?
16. Define restorative state.
17. What is normal state?
18. What are the tasks of energy control center?
19. What are the important types of relay used for protection,
20. Denote the hierarchical levels used in EMS.
21. Write the importance of state estimation in power system.
22. List out the conditions for normal operation of power system.
23. What are the functions of load control centre?

Part-B
1. Briefly explain various functions of SCADA with neat diagram. Also list some of the
common features of all SCADA systems
2. Discuss the various functions, system monitoring and control of load dispatch center.
3. (i) What is EMS? What are its major functions in power system operation and control?
(ii) Draw the block diagram to show the hardware configuration of a SCADA system for
a power system and explain the application of SCADA in monitoring and control of
power system
4. Explain the security monitoring using state estimation with necessary diagrams.
5. (i)Explain need of computer control of power system.
 (ii) Explain the major functions of system security control.
6. Explain various state transitions and control strategies using state transition diagram.
7. Briefly discuss the various functions of energy control centre.
8. List the various contingencies that are generally considered for steady sate security
analysis. Explain the major functions of system security control.
9. Write short notes on energy control centre EMS and its functions.
10. Explain the state estimation method in power system.
11. (i) Explain the network topology determination method with the factors involved in it.
(ii) Explain the power system security and control with neat flow chart.