Scribd
Upload
118 views

Fault Finding: Section C - Electrics

The document provides a list of error codes and descriptions for various electrical faults that may occur on a JCB Servicemaster machine. There are over 20 error codes listed relating to open or short circuits affecting systems like hydraulic solenoids, sensors, and machine control outputs. The errors codes indicate which specific component has a fault, such as a grab/rotate solenoid, fuel level sensor, or interior light that may be open or short circuited. This list allows technicians to quickly identify and diagnose electrical issues in these machines.

Uploaded by

Andrey
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
118 views

Fault Finding: Section C - Electrics

The document provides a list of error codes and descriptions for various electrical faults that may occur on a JCB Servicemaster machine. There are over 20 error codes listed relating to open or short circuits affecting systems like hydraulic solenoids, sensors, and machine control outputs. The errors codes indicate which specific component has a fault, such as a grab/rotate solenoid, fuel level sensor, or interior light that may be open or short circuited. This list allows technicians to quickly identify and diagnose electrical issues in these machines.

Uploaded by

Andrey
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Section C - Electrics

Fault Finding
JCB Servicemaster

Error Codes Error String Description


130 GRB CW The grab/rotate clockwise solenoid is open-circuit.
131 GRB CCW The grab/rotate counter-clockwise solenoid is open-circuit.
132 LW FLOW The low flow solenoid is open-circuit.
133 ISOL The hydraulic isolator solenoid is open-circuit.
135 2 STAGE The 2nd stage relief solenoid is open-circuit.
136 QK HTCH The quick hitch solenoid is open-circuit.
138 HAMMER The hammer solenoid is open-circuit.
139 CUSHION The hard/soft cushion solenoid is open-circuit.
142 ENG SD The engine shutdown output is open-circuit.
143 GLW PLG The glow plugs output is open-circuit.
156 TL FLW3 The travel flow 3 solenoid is open-circuit.
157 TL FLW2 The travel flow 2 solenoid is open-circuit.
158 GR CHNG The M2 or gear change solenoid is open-circuit.
159 BRKE LT The brake light output is open-circuit.
160 AXLE LK The axle lock solenoid is open-circuit.
161 STAB UP The stabilizer up solenoid is open-circuit.
162 STAB DN The stabilizer down solenoid is open-circuit.
163 STAB LH The stabilizer left solenoid is open-circuit.
164 STAB RH The stabilizer right solenoid is open-circuit.
165 CRUISE The cruise control solenoid is open-circuit.
166 DIG ISL The dig end isolation solenoid is open-circuit.
167 PRK BK The M1 or park brake solenoid is open-circuit.
168 DRV ISL The drive isolate solenoid is open-circuit.
202 FUEL The fuel level sensor is short-circuit.
203 EN TMP The engine temperature sensor is short-circuit.
204 HYD TMP The hydraulic temperature sensor is short-circuit.
205 SET PT The throttle set potentiometer is short-circuit.
206 SENS PT The throttle sense potentiometer is short-circuit.
210 THR SOL The throttle solenoid is short-circuit. This can only be detected when the engine is not
running.
211 BOOM SP The boom lower speed regulation output is short-circuit.
212 INT LT The interior light is short-circuit.
213 MAX FLW "The max flow solenoid is short-circuit. For JS200W machines, this error can only be
detected when the engine is not running due to the fact that this is a proportional valve
on these machines.
214 BEACON The beacon output is short-circuit.
215 BOOM PR The boom priority solenoid is short-circuit.
216 FL PMP The refuel pump solenoid is short-circuit.

C-190 9803/6590-3 C-190

You might also like