CT10X

Barcode Scanner

Instruction Manual

Downloaded from www.Manualslib.com manuals search engine

 IMPORTANT NOTICE

Safety Precaution
* DO NOT disassemble the scanner, or place foreign
matter into the scanner cause a short circuit or circuit
damage.
* DO NOT expose the scanner or battery to any
flammable sources.

Maintenances Precaution
* Use a clean cloth to wipe dust off the body of the
scanner.
* If you find the scanner abnormal, write down the
specific scenario and consult the maintenance person.

2
Downloaded from www.Manualslib.com manuals search engine
 Contents

IMPORTANT NOTICE ...................................................................... 2

Safety Precaution. ..................................................................... 2
Maintenances Precaution. ......................................................... 2
Contents. .......................................................................................... 3
Overview of CT10X Barcode Scanner .............................................. 5
Features of the Scanner ............................................................ 5
Appearance. .............................................................................. 5
Introduction of Key Function. ..................................................... 6
Specifications. ............................................................................ 6
Correct Aiming. .......................................................................... 7
Incorrect Aiming. ........................................................................ 7
QUICK START ........................................................................................ 7
Enter the Setting Mode. ............................................................. 9
Exit the Setting Mode with Save................................................. 9
Exit the Setting Mode without Save............................................ 9
Restore Factory Defaults. ........................................................ 10
Check Software Version. ......................................................... 10
Save Custom Settings. .............................................................11
Chapter 1 Features and Basic Setups............................................ 12
1.1 Battery ............................................................................ 13
1.1.1 Mounting the battery(charging). ............................. 13
1.1.2 How to operate CT10X Barcode Scanner .................. 13
1.1.3 Auto Power Off. ...................................................... 13
1.2 Transmit Buffer ............................................................... 14
1.2.1 Inventory Mode. ..................................................... 16
1.3 LED Indicator.................................................................. 17
1.4 Beeper ........................................................................... 17
1.4.1 Beeper Volume. ..................................................... 18
1.5 Scan Modes. ................................................................... 19
1.5.1 Manual Mode. ........................................................ 19
1.5.2 Auto Power Off Mode. ............................................ 20
1.5.3 Auto-induction Mode. ............................................. 21
1.6 Symbologies Supported...................................................... 22
1.7 USB Wired Data Transmission........................................ 22
Chapter 2 How to Connect with BT ................................................ 23
2.1.Select Output Interface. .................................................. 24
2.1.1 BT SPP Mode. ....................................................... 24

3
Downloaded from www.Manualslib.com manuals search engine
 2.1.2 BT HID Mode............................................................. 24
2.2 Setting up a BT connection. ............................................ 25
2.3 Connect to PC via BT ...................................................... 26
2.4 Connect to PDA via BT .................................................... 31
2.4.1 One-click Android Connection. ................................... 36
2.4.2 One-click iOS Connection. ......................................... 39
2.4.3 Connect via BT Input Method.................................. 42
Chapter 3 SYMBOLOGY SETTINGS. ............................................ 45
3.1 Codabar ........................................................................... 46
3.2 Code25: Industrial 25. ...................................................... 47
3.3 Code25: Interleaved 25. ................................................... 48
3.4 Code25: Matrix 25. ........................................................... 49
3.5 Code25: Standard 25. ...................................................... 50
3.6 Code 39. .............................................................................. 51
3.6.1 Enable/Disable Code 39. ......................................... 51
3.6.2 START/STOP Transmission. .................................... 51
3.6.3 Checksum Verification. ............................................. 52
3.6.4 Standard/Full ASCII Code 39. .................................. 53
3.7 Code 93. .............................................................................. 54
3.8 Code 128. ............................................................................ 55
3.9 EAN-8. ................................................................................. 54
3.9.1 Enable/Disable EAN-8. ............................................ 55
3.9.2 Convert to EAN-13. .................................................. 56
3.9.3 Checksum Transmission. ......................................... 57
3.10 EAN-13. ............................................................................. 58
3.10.1 Enable/Disable EAN-13. ........................................ 58
3.10.2 Convert to ISBN. .................................................... 58
3.10.3 Checksum Transmission. ....................................... 59
3.11 UPC-A. ............................................................................... 60
3.11.1 UPC-A Output “0”. .................................................. 60
3.11.2 UPC-A Checksum Transmission. ........................... 60
3.12 UPC-E. ............................................................................... 61
3.12.1 Enable/Disable UPC-E. ......................................... 61
3.12.2 UPC-E Checksum Transmission. .......................... 61
3.13 MSI. .................................................................................... 62

4
Downloaded from www.Manualslib.com manuals search engine
 Overview of CT10X Barcode Scanner

Features of the Scanner

* Small size, portable.
* User feedback via LED indicator and beeper
* The voice volume of scan barcode successfully could change via
setting barcode.
* Built-in 256 KB Flash memory can store up to thousand scan
barcodes.
* Provides 2 KB memory for reserve buffer while Bluetooth
connection interrupt, can store up to 110 scan barcodes.
* Supports BT SPP.
* Supports BT HID.

★ Supports a wide range of barcode types. FedEx and USPS

barcodes are all supported.
★ Whole body shockproof and drop resistance design
★ Proprietary intellectual property rights
★ Comfortable operating feel
★ Button life up to 3 million times
★ Support BT standard protocol, no need adaptor
★ 1500mAh large capacity lithium battery
★ Long working hours
★ The maximum readable digit extend to 64-bit. CT10X both wired
and wireless mode support 64bit readable
★ Prefix and suffix are allowed to be added. Reset to factory default
settings by scanning the “Factory Reset” barcode.

Appearance

Scan Wi

Bluet o ot h W i re less mo de USB W ire d mo de

5
Downloaded from www.Manualslib.com manuals search engine
 Introduction of Key Function
* Long press Scan button 3 seconds will turn on the CT10X
scanner.
* Long press Scan button 3 seconds will turn off the CT10X
scanner.
* Flip the Scan button can read the barcodes.

Specifications
PHYSICAL CHARACTERISTICS
Material ABS+TPU
Size Length 160mm*Width 70mm* Height 90mm
Color White, Black
Power supply Built-in rechargeable lithium battery
Weight 150g(With battery)

PERFORMANCE CHARACTRISTICS
Bluetooth Bluetooth class 2.0, Version +EDR
Interfaces Supported USB, RS232, PS2 Keyboard
Light Source (Laser) Laser LED 650+/-20nm
Sensor 2500 pixels
Decode Capability Codabar, USPS, FedEx, UPC-E, Code 93,
MSI, Code 128, UCC/EAN-128, Code 39,
EAN-8, EAN-13, UPC-A, ISBN, Industrial 25,
Interleaved 25, Standard 25, 2/5 Matrix
Resolution 5mil
Nominal Working Distance 6~30cm
Decode Rate 100 decodes per second
Scan width 30mm=Scanner Window
Decode mode Single-Line Aiming
Scan mode Auto off mode / Manual mode
Print Contrast Minimum 30%
Scan angles Roll30° Pitch75° Yaw65°
Cylinder Horizontal Scan Diameter 35mm
Indication Beeper, LED
Radio Range 10m Visual range

POWER
Voltage DC 5V
Laser Safety Accord with national level two laser safety
standards
EMC CE & FCC DOC Compliance
standby Current 35mA
Operating current 60mA

6
Downloaded from www.Manualslib.com manuals search engine
 USER ENVIRONMENT
Operating Temp. 0 to 50. °C / 32 to 122°F
Storage Temp. 0 to 50. °C / 32 to 122°F
Operating Humidity 20-85% ( non-condensing )
Storage Humidity 20-85% ( non-condensing )
Drop Specifications Free fall of 1.5m air drop
Accessories Lithium battery, Charger., Data lines

Correct Aiming

Incorrect Aiming

QUICK START
The setting of the CT10X Barcode Scanner can be changed by
reading the setup barcodes contained in this manual. This section
describes the procedure of setting the CT10X Barcode Scanner by
reading the setup barcodes and provides some example for
demonstration.

Step 1: Turn on CT10X Barcode Scanner. It will response with a

long beep(high tone), it's LED shows red and with Intmt
twinkle.
Note: How the CT10X Barcode Scanner establishes a
connection with computer or other compatible device,
please refer to Chapter 2.

Step 2: Enter the Setting Mode. The CT10X Barcode Scanner

will response three beeps (tone descending from high to
low), and its LED indicator will flashing purple.

7
Downloaded from www.Manualslib.com manuals search engine
 Enter Setup

Step 3: Read a Setup barcode. The CT10X Barcode Scanner will

response three beeps (tone ascending from low to high),
and its LED indicator will flashing purple.
For Example:

Enable Codabar

Step 4: Exit the Setting Mode. The CT10X Barcode Scanner will
response three beeps (tone descending from high to low),
and its LED indicator will not flashing purple and power off.
Note: When any setup error occurs, the CT10X Barcode
Scanner will respond with a long beep (low tone), and its
LED indicator will flashing purple.

Exit with Save

Steps of Setup

Enter Setup

Details (eg: Enable/Disable a Barcode)

Exit Setup

8
Downloaded from www.Manualslib.com manuals search engine
 Enter the Setting Mode
For the scanner to enter the setting mode, you must have it read the
"Enter Setup" barcode, which will be located at the bottom of almost
every page of this manual.
The CT10X Barcode Scanner will respond with three beeps (tone
descending from high to low), and its LED indicator becomes purple
and go off quickly after reading the barcode.

Enter Setup

For setting scanner parameters, see "Read a Setup Barcode" below.

Exit the Setting Mode with Save

For the scanner to exit the setting mode, you must have it read the
"Exit with Save" barcode, which will be located at the bottom of
almost every page of this manual.
Just like reading the "Enter Setup" barcode, the scanner will respond
with three beeps (tone ascending from low to high) after reading the
barcode.

Exit with Save

Exit the Setting Mode without Save

If you want to exit the setting mode without saving any changes, you
must have the scanner read the "Exit without Save" barcode.
Just like reading the "Enter Setup" barcode, the scanner will respond
with three beeps (tone ascending from low to high) after reading the
barcode.

Exit without Save

9
Downloaded from www.Manualslib.com manuals search engine
 Restore Factory Defaults
"Restore Factory Defaults" is a special barcode. The CT10X
Barcode Scanner will respond with a short beep (high tone) after
reading this barcode. At this time, the scanner system could restore
factory defaults, and no need to read "Exit with Save" barcode
again. The Scanner defaults enable HID, PIN defaults 10010.

Restore Factory

Note: Most of setting mode have restore factory defaults selection.

The factory default value for each setting is indicated by an asterisk
"*".
You could use this barcode at the following status:
1. The scanner can not work. For example, it can not read barcodes.
2. You forget the settings you did to the scanner before, and you
don't want to be affected by the settings when you use the
scanner.
3. After using a function which is not be used usually in the scanner.

Check Software Version

If you want to know the software version of CT10X, should read the
‘Enter Setup’ and ‘Output Software Version’ barcode:

Enter Setup

Output Software Version

Checking the software version is done at the enter setup mode, so

after output the software version, need to read ‘Exit without Save’
barcode.

Exit without Save

10
Downloaded from www.Manualslib.com manuals search engine
 Save Custom Settings
1. You may change factory defaults, and customize some functions
suitable for your own applications when you use CT10X, you
must read the ‘Enter Setup’ Function barcode you want to
customize ‘Save Custom Settings’ ‘Exit with Save’ barcodes.

Enter Setup

Save Custom Settings

Restore Customs Settings

Exit with Save

2. If you want to restore to custom settings after resetting the

barcode scanner, just need to read ‘Enter Setup’ ‘Restore Custom
Settings’ ‘Exit with Save’ barcodes as above.

11
Downloaded from www.Manualslib.com manuals search engine
 Chapter 1 Features and Basic Setups
This chapter will introduce the features and usage of the barcode
scanner.

Contents

1.1 Battery ...................................................................................... 13

1.1.1 Mounting the battery(charging)........................................ 13
1.1.2 How to operate CT10X Barcode Scanner........................ 13
1.1.3 Auto Power Off. ............................................................ 13
1.2 Transmit Buffer ......................................................................... 14
1.2.1 Inventory Mode. .............................................................. 16
1.3 LED Indicator ........................................................................... 17
1.4 Beeper ..................................................................................... 17
1.4.1 Beeper Volume. .............................................................. 18
1.5 Scan Modes. ............................................................................ 19
1.5.1 Manual Mode. ................................................................. 19
1.5.2 Auto Power Off Mode. .................................................. 20
1.5.3 Auto-induction Mode. ...................................................... 21
1.6 Symbologies Supported. .......................................................... 22
1.7 USB Wired Data Transmission. ............................................... 22

12
Downloaded from www.Manualslib.com manuals search engine
 1.1 Battery
The scanner is powered by 1500mAh chargeable Lithium batteries.
The batteries can support the scanner work continuous for 60 hours,
or read 56000 barcodes (read an EAN-13 barcode per 5s).

1.1.1 Mounting the battery (charging)

1. Hold the scanner face down in one hand.
2. Insert USB cable for charging.

1.1.2 How to operate CT10X Barcode Scanner

Turn on the scanner
Press the Power key for about 2 seconds. The scanner will respond
with a long beep (high tone), and its LED indicator is flashing.

Turn off the scanner

Press the Power key for about 3 seconds. The scanner will respond
with two short beeps (high tone) and the LED indicator is turn off.

1.1.3 Auto Power Off

In order to conserve battery power, the user can specify the time
interval for the scanner to automatically turn off. By default, it is set
to 10 minutes.

Enter Auto Power Off

5min (*)10min

20min 30min

13
Downloaded from www.Manualslib.com manuals search engine
 Exit Auto Power Off

For example: Set 20 minutes for the scanner to automatically turn off.
1. Read the "Enter Setup" barcode;
2. Read the "Enter Auto Power Off" barcode;
3. Read the "20min" barcode;
4. Read the "Exit with Save" barcode.
Note: If you want to keep the scanner power on all the time, read
"Exit Auto Power Off" in stead of step 3 and 4.

Enter Setup

Exit with Save

Exit without Save

1.2 Transmit Buffer

During the Bluetooth connection, the CT10X Scanner uses a 16KB
memory as a data buffer, and sends the collected data to the host
computer one by one via the Bluetooth. Upon reading a barcode
successfully, the scanner responds with one short beep and its LED
indicator becomes green and goes off quickly. However, the host
computer may not receive the data immediately if getting out of
range. With the 256KB transmit buffer, the scanner can ignore the
transmission status and keep on reading barcodes until the buffer is
full. When the buffer is full, the scanner will respond with a long beep
(low tone), this reminds the user that the space of buffer is not
enough and can not read barcode any more. Once the Buffer is

14
Downloaded from www.Manualslib.com manuals search engine
 full, the user should return to the range of BT connection quickly,
the data in the buffer can be sent back to the host computer and
release the space of buffer.
Note: The 256KB transmit buffer on the scanner can hold as many
as 2600 barcodes bases on Code128. You can choose to clear the
data in the buffer every time when you turn on the scanner.

Enable Clear Data in Buffer When *Disable Clear Data in Buffer When
Turn On the Scanner Turn On the Scanner

Note: You can clear the data in the buffer via enable barcode, you
can also clear the data in the buffer via press the Power key long
time.
After the Bluetooth connect successfully, the barcodes in the buffer
will upload to appointed position automatically. You also can setup
upload the barcodes in the buffer or not via reading the following
barcodes. By default, it is enabled.
If you don‘t want to upload the barcodes automatically, you can
setup as disabled, when the Bluetooth connect, the barcodes won’t
upload. You can double click Power key to start uploading the
barcodes.

(*)Enable Auto Uploading Disable Auto Uploading

Enter Setup

Exit with Save

Exit without Save

15
Downloaded from www.Manualslib.com manuals search engine
 1.2.1 Inventory Mode
If you want to keep the barcodes in the buffer of CT10X for multiple
uploading, you can choose inventory mode. In inventory mode,
CT10X will count the number of the barcodes automati- cally, and
control the time, position etc. for uploading. Also, you can clear the
barcodes in the buffer after uploading. Following is the setup
method:
1. Read ‘Enter Inventory Mode’ barcode to enter into the inventory
mode

Enter Inventory Mode

2. If you want to recover to normal mode, read the ‘Enter Normal

Mode’ barcode

Enter Normal Mode

3. Read the ‘Clear the barcodes in the buffer’ barcode to clear the
barcodes (only suitable for inventory mode)

Clear the barcodes in the buffer

4. Read ‘Data Uploading’ barcode to upload the barcodes in the

buffer (only suitable for inventory mode)

Data Uploading

5. Read ‘Upload Counting’ barcode to count the number of the

barcodes (only suitable for inventory mode)

Upload Counting

Note: Inventory function can be used under any scan mode

mentioned in 1.5.

16
Downloaded from www.Manualslib.com manuals search engine
 1.3 LED Indicator
The LED indicators on CT10X can help the user know about the
current operation status.

COLOR OF LED INDICATOR MEANING

Green LED on and off quickly Good Read, with one short beep (high
tone)
Green LED on Every 5s Indicates the CT10X Scanner in Memory
Mode
Purple, Flashing(On/Off ratio 1:1) Indicates the CT10X Scanner in Setting
mode
Blue, Flashing (On/Off ratio 1:1) Indicates the BT is waiting for connection,
the CT10X stores the address of BT
which connects with the last time.
Indicates the CT10X Scanner is out of
range or can not establish connection with
BT, with two short beeps(high-low tone)
Blue, Flashing (On/Off ratio 20ms:3s) Indicates the CT10X Scanner establish a
BT connection successfully, with two short
beeps (low-high tone).
Indicates the CT10X Scanner reconnect
with BT, with two short beeps (low-high
tone).
Red, Flashing (On/Off ratio 1:1) Indicates the CT10X Scanner has no
address of BT which connects with before.
The default BT connect interface is HID,
the PIN code is 10010.

1.4 Beeper
The beeper built in CT10X can help the user know about the
current operation status.

BEEPING MEANING
One long beep, high tone Power on. If the scanner has no BT
address which could connect with, flashing
red. If the scanner has BT address which
could connect with, flashing blue.
One short beep, high tone Read barcode, with green LED on and off
quickly
One long beep, low tone Configuration error, with purple flashing;
Or transmit buffer full, with green LED on
and off quickly
Two short beeps, high tone Power off.
Two short beeps, low-high tone BT connection established, with blue LED
flashing (On/Off ratio 20ms:3s).
Two short beeps, high-low tone BT connection out of range or suspended,
with blue LED flashing (On/Off ratio 1:1).

17
Downloaded from www.Manualslib.com manuals search engine
 Three short beeps, tone descending Enter or Exit Setting mode, with purple
from high to low LED flashing.
Three short beeps, tone ascending Configuration correct, with purple LED
from low to high flashing;

1.4.1 Beeper Volume

Mute Minimum Volume

(*)Medium Volume Maximum Volume

For example: Set Minimum Volume for beeper.

1. Read the "Enter Setup" barcode;
2. Read the "Minimum Volume" barcode;
3. Read the "Exit with Save" barcode.

Enter Setup

Exit with Save

Exit without Save

18
Downloaded from www.Manualslib.com manuals search engine
 1.5 Scan Modes
Three kinds of scan modes are supported by the CT10X Barcode
Scanner:

1.5.1 Manual Mode

By default, the scan mode is set to Manual Mode. If the user keeps
press the Scan Key, the CT10X Scanner will emit a red light line.
This indicates the scanner could scan, the scanning will not stop
until the scanner under the following situation.

* Read a barcode successfully;

* Release the Scan Key.

Manual Mode

Enter Setup

Exit with Save

Exit without Save

20
Downloaded from www.Manualslib.com manuals search engine
 1.5.2 Auto Power Off Mode

(*)Auto Power Off Mode

Setup Auto Power Off Time

Enter Setup

Exit with Save

Exit without Save

20
Downloaded from www.Manualslib.com manuals search engine
 1.5.3 Auto-induction Mode
Under the Auto-induction Mode. The users just need to move the
barcodes to be scanned in front of the light band of CT10X, no need
press the Scan Key, there will show a red light line. This indicates
the scanner could scan, the scanning will not stop until the scanner
under the following situation.

* Read a barcode successfully;

*The pre-set timeout expires (the default time is 2s).

induction Mode

You also can setup the best auto-induction distance according to

actual demand, read the following barcode for setup.

Setup Auto-induction Distance

For Example:
1. Read the "Enter Setup" barcode;
2. Read the "Auto-induction Mode" barcode;
3. Read the "Setup Auto-induction Distance";
4. Read the numeric barcode in Appendix I; (0 means farthest, 9
means nearest)
5. Read the "Exit with Save" barcode.
Then enter the Auto-induction Mode.

Enter Setup

Exit with Save

Exit without Save

21

Downloaded from www.Manualslib.com manuals search engine

 1.6 Symbologies Supported
Most of the popular barcode symbologies are supported by the
CT10X Scanner, as listed below. Refer to Chapter 4 for details of
each symbology.

Symbologies Supported: Enable/Disable Pre-Set

Codabar Enable
Code 93 Enable
MSI Disable
USPS Enable
FedEx Enable
Code 128 Enable
UCC/EAN-128 Enable
Code 39 Enable
EAN/UPC EAN-8 Enable
EAN-13 Enable
UPC-A Enable
UPC-E Enable
ISBN Disable
Code 2 of 5 Industrial 25 Disable
Interleaved 25 Enable
Standard 25 Enable
2/5 Matrix Disable

1.7 USB Wired Data Transmission

CT10X Barcode Scanner support USB Data live transmission. The
user just need connect one end of the USB cable to a device with
USB2.0 port, and the other end to CT10X, open a textbox, it will enter
data transmission. USB wired transmission is the prior transmission
mode.

22

Downloaded from www.Manualslib.com manuals search engine

 Chapter 2 How to Connect with BT
1. Make CT10X full charged, press Power key. If the scanner never
connected with the computer before, it will responds with a beep,
and flashing red.
2. Have the scanner read the "Enter Setup" barcode to enter the
setting mode.
3. Have the scanner read the associated barcode to activate the BT
connection interface.
4. Have the scanner read the barcodes for related settings.
5. Have the scanner read the barcode to exit the setting mode.
6. The CT10X Scanner will stay active for 1 minute waiting for a
connection request from the host(SPP) or trying to connect to the
host(HID).

Contents

2.1.Select Output Interface. ........................................................... 24

2.1.1 BT SPP Mode. ................................................................ 24
2.1.2 BT HID Mode. ................................................................. 24
2.2 Setting up a BT connection....................................................... 25
2.3 Connect to PC via BT ............................................................... 26
2.4 Connect to PDA via BT ............................................................. 31
2.4.1 One-click Android Connection.................................... 36
2.4.2 One-click iOS Connection.......................................... 39
2.4.3 Connect via BT Input Method..................................... 42

23

Downloaded from www.Manualslib.com manuals search engine

 2.1. Select Output Interface
Either SPP or HID can be chosen depending on the need.

2.1.1 BT SPP Mode

If you select the output interface of BT SPP, you may run
HyperTerminal.exe or serial port tool to collect the scanned data.

Enable SPP

You can setup SPP data batch upload or single upload according to
your requirements.

SPP Data Batch Upload

SPP Data Single Upload

2.1.2 BT HID Mode

By default, BT HID is activated on the CT10X Scanner, and the
keyboard type is set to PCAT (US).

(*)Enable HID Enter Setup

Exit with Save

Exit without Save

24

Downloaded from www.Manualslib.com manuals search engine

 2.2 Setting up a BT connection
Specify the PIN Code, if you choose "The Default Value 1", the
passkey for setting up a BT connection is 10010; If you choose "The
Default Value 2", the passkey for setting up a BT connection is
40510.
For security concerns, the user can also specify a unique PIN code.
1. Read the "Enter PIN Code" barcode;
2. Read the setting barcodes of parameters' value in APPENDIX
ONE, if the scanner read the setting barcodes 1, 5, 1, 5, 1, 5 in
order, it means the PIN code is 151515.
10010 40510

(*)Default Value 1 Default Value 2

Enter PIN Code Random PIN Code

Refer to APPENDIX I.
Note: Before the CT10X Scanner connects with the other devices,
the user should pre-set the scanner.
For example: The CT10X Scanner is trying to connect with a host
computer, the setting operation is according to the following steps:
1. Read the "Enter Setup" barcode;
2. Read the "Enable SPP" barcode;
3. Read the "Default Value 1"(PIN code is 10010);
4. Read the "Exit with Save" barcode.

Enter Setup

Exit with Save

Exit without Save

25

Downloaded from www.Manualslib.com manuals search engine

 2.3 Connect to PC via BT
Steps: Turn on Bluetooth of your computer (take Win7 as example)
(Note: If your computer without Bluetooth, you should
prepare a Bluetooth Adapter, Insert the adapter to USB port)

Click ‘AddaDevice‘,

It will search for the devices, show the following window:

26

Downloaded from www.Manualslib.com manuals search engine

 The computer will search Bluetooth devices automatically. A
few seconds later, you will find CT******** in the available
devices list, click ’Next‘

Select ’Enter the device‘s pairing code’, and click ’Next‘.

Input the pairing code 10010, and click ’Next’.

27

Downloaded from www.Manualslib.com manuals search engine

 You can find a prompting at the lower right corner of your
computer desktop, as following.

After around 5 seconds, you will hear a beep from CT10X, and
the indicator from red to blue. Then connect successfully.

28

Downloaded from www.Manualslib.com manuals search engine

 You can open a editable textbox (Notepad, word etc.), and
read the barcodes.

(Note:After pairing successfully, open Bluetooth Chat, then

you can read the barcodes in SPP mode.)

Now, you click ‘Show Bluetooth Devices’, you can find the
CT10X in Devices and Printers.

29

Downloaded from www.Manualslib.com manuals search engine

 If you want to change PIN code or switch output interface, you
must remove the paired CT10X on the computer first.

30

Downloaded from www.Manualslib.com manuals search engine

 Note: CT10X default mode is HID Mode, if you want to use
SPP mode, just read following barcodes before pairing, other
operations is same as HID mode.

2.4 Connect to PDA via BT

PDA is trying to connect to the CT10X Scanner (BT SPP).
1. Press the Power key and turn on the CT10X Scanner with
correct BT settings, such as setting up SPP as BT transmit
interface, and BT PIN code specified, etc.
2. Find the BT icon on PDA, and double-click.

31
Downloaded from www.Manualslib.com manuals search engine
 3. Click [Add New Device].

4. Choose "CT10X", click [Next].

32
Downloaded from www.Manualslib.com manuals search engine
 4. Choose "CT********", click [Next].

5. Enter the PIN Code. When setting up a BT connection, if you

choose "The Default Value 1", input 10010; If you choose "The
Default Value 2", input 40510; if you specified a unique PIN code
on your own, input it. Click [Next].

6. Click [Finish]. Click [New Transmit Port] in [COM port].

33
Downloaded from www.Manualslib.com manuals search engine
 7. Choose port number for added device. [COM0] is chosen here.
Click [OK].

34
Downloaded from www.Manualslib.com manuals search engine
 8. Enter serial port application, choose the port number you just
set, click [open]. The CT10X Scanner respond with two short
beeps, and the indicator is flashing blue (On/Off ratio 20ms:3s),
indicating the connection between PDA and CT10X is
established successfully.

35
Downloaded from www.Manualslib.com manuals search engine
 2.4.1 One-click Android Connection
1. Turn on CT10X, read the following barcodes continuously

Enter Setup

One -click android connection

Exit with Save

2. Bluetooth Pairing
Turn on Bluetooth in your android device, search CT******** in
available devices, and click.

It will popup Bluetooth pairing request dialog, input the PIN code
10010.

36
Downloaded from www.Manualslib.com manuals search engine
 Click OK, you will hear a beep from CT10X, that means pairing
successfully, you can find paired CT10X on the android device.

37
Downloaded from www.Manualslib.com manuals search engine
 Open a textbox, for example short message, the CT10X can read
barcodes into the textbox.

38
Downloaded from www.Manualslib.com manuals search engine
 2.4.2 One-click iOS Connection
1. Turn on CT10X, and read the following barcodes continuously

Enter Setup

One-click iOS Connection

Exit with Save

2. Bluetooth Pairing
Turn on Bluetooth in your ios device, search CT******** in
available devices, and click

39
Downloaded from www.Manualslib.com manuals search engine
 It will popup Bluetooth pairing request dialog, and show the PIN
code

Find above mentioned numbers in following barcodes, read them

continuously, and then read “Exit without Save” barcode

Exit without Save

You will hear a beep from CT10X if connect successfully, and it will
show in the paired devices on iOS device.

40

Downloaded from www.Manualslib.com manuals search engine

 3. Active or Hide the Input Method
During the scanning, you may use the soft keypad if you want to
add remark information, you just need double click Power key
quickly, it will active the soft keypad. If you double click Power
key quickly again, the soft keypad will hide. It is shown as
following:

41

Downloaded from www.Manualslib.com manuals search engine

 2.4.3 Connect via BT Input Method
1. Turn on Bluetooth barcode scanner CT10X for setup
Read “Enter Setup” barcode

Enter Setup

Read “Bluetooth Input Method” barcode

Bluetooth Input Method

Read “Exit with Save” barcode

Exit with Save

2. Setup “CILICO Bluetooth barcode input method”

Step 1: Tap “Select Input Method”

42

Downloaded from www.Manualslib.com manuals search engine

 Select Cilico Bluetooth Input method (support Chinese,
English and Japanese)

Step 2:Bluetooth Pairing

Turn on Bluetooth

43

Downloaded from www.Manualslib.com manuals search engine

 Click "Search for devices", and will find CT10X in
available devices

Click for pairing, and input the PIN code in following

window, then click OK.

44

Downloaded from www.Manualslib.com manuals search engine

 You will find CT10X in Paired Devices if pairing
successfully.

Step 3:Tap "Select Bluetooth device"

45

Downloaded from www.Manualslib.com manuals search engine

 Click CT10X in Bluetooth Paired Device List, it will
connect automatically

You will hear a beep if connect successfully

46

Downloaded from www.Manualslib.com manuals search engine

 Step 4:Tap "Switch Input Method"

Select Cilico Bluetooth Input method (support Chinese,

English and Japanese), the user can choose according
to their requirement

47

Downloaded from www.Manualslib.com manuals search engine

 Step 5:Tap "Finish"

Step 6:Open a editable textbox, then can read the

barcodes

48

Downloaded from www.Manualslib.com manuals search engine

 Switch to Chinese input method

Switch to English input method

43

Downloaded from www.Manualslib.com manuals search engine

 Switch to Japanese input method

44

Downloaded from www.Manualslib.com manuals search engine

 Chapter 3 Symbology Settings

In this chapter, a brief on the symbology setting is provided for your

reference.

Contents

3.1 Codabar .................................................................................... 46

3.2 Code25: Industrial 25. ............................................................... 47
3.3 Code25: Interleaved 25. ............................................................ 48
3.4 Code25: Matrix 25..................................................................... 49
3.5 Code25: Standard 25. ............................................................... 50
3.6 Code 39..................................................................................... 51
3.6.1 Enable/Disable Code 39. .............................................. 51
3.6.2 START/STOP Transmission. ........................................... 51
3.6.3 Checksum Verification. ................................................. 52
3.6.4 Standard/Full ASCII Code 39. .......................................... 53
3.7 Code 93..................................................................................... 54
3.8 Code 128................................................................................... 55
3.9 EAN-8........................................................................................ 54
3.9.1 Enable/Disable EAN-8. .................................................... 55
3.9.2 Convert to EAN-13. .......................................................... 56
3.9.3 Checksum Transmission. ................................................. 57
3.10 EAN-13.................................................................................... 58
3.10.1 Enable/Disable EAN-13. ................................................ 58
3.10.2 Convert to ISBN. ............................................................ 58
3.10.3 Checksum Transmission. ............................................... 59
3.11 UPC-A...................................................................................... 60
3.11.1 UPC-A Output “0”. .......................................................... 60
3.11.2 UPC-A Checksum Transmission. ................................... 60
3.12 UPC-E...................................................................................... 61
3.12.1 Enable/Disable UPC-E. ................................................. 61
3.12.2 UPC-E Checksum Transmission. .................................. 61
3.13 MSI. ........................................................................................ 62

45

Downloaded from www.Manualslib.com manuals search engine

 3.1 Codabar
Decide whether or not to enable Codabar. The CT10X Scanner
defaults enable Codabar.

（*）Enable Codabar

Disable Codabar

Note: Read the "Disable Codabar" barcode will make the scanner
can not read the Codabar barcode. Thus, if the scanner can not read
the Codabar barcode, please trying to read "Enable Codabar" to
reset.

For example: Enable Codabar.

1. Read the "Enter Setup" barcode;
2. Read the "Enable Codabar" barcode;
3. Read the "Exit with Save" barcode.

Enter Setup

Exit with Save

Exit without Save

46

Downloaded from www.Manualslib.com manuals search engine

 3.2 Code25: Industrial 25
Decide whether or not to enable Industrial 25. The CT10X Scanner
defaults disable Industrial 25.

Enable Industrial25

（*）Disable Industrial 25

Note: Read the "Disable Industrial 25" barcode will make the
scanner can not read the Industrial 25 barcode. Thus, if the scanner
can not read the Industrial 25 barcode, please trying to read "Enable
Industrial 25" to reset.

For example: Enable Industrial 25.

1. Read the "Enter Setup" barcode.
2. Read the "Enable Industrial 25" barcode.
3. Read the "Exit with Save" barcode.

Enter Setup

Exit with Save

Exit without Save

47

Downloaded from www.Manualslib.com manuals search engine

 3.3 Code25: Interleaved 25
Decide whether or not to enable Interleaved 25. The CT10X
Scanner defaults disable Interleaved 25.

Enable Interleaved 25

（*）Disable Interleaved

Note: Read the "Disable Interleaved 25" barcode will make the
scanner can not read the Interleaved 25 barcode. Thus, if the
scanner can not read the Interleaved 25 barcode, please trying to
read "Enable Interleaved 25" to reset.

For example: Enable Interleaved 25.

1. Read the "Enter Setup" barcode;
2. Read the "Enable Interleaved 25" barcode;
3. Read the "Exit with Save" barcode.

Enter Setup

Exit with Save

Exit without Save

48

Downloaded from www.Manualslib.com manuals search engine

 3.4 Code25: Matrix 25
Decide whether or not to enable Matrix 25. The CT10X Scanner
defaults enable Matrix 25.

（*）Enable Matrix 25

Disable Matrix 25

Note: Read the "Disable Matrix 25" barcode will make the scanner
can not read the Matrix 25 barcode. Thus, if the scanner can not
read the Matrix 25 barcode, please trying to read "Enable Matrix 25"
to reset.

For example: Enable Matrix 25.

1. Read the "Enter Setup" barcode;
2. Read the "Enable Matrix 25" barcode;
3. Read the "Exit with Save" barcode.

Enter Setup

Exit with Save

Exit without Save

49

Downloaded from www.Manualslib.com manuals search engine

 3.5 Code25: Standard 25
Decide whether or not to enable Standard 25. The CT10X Scanner
defaults enable Standard 25.

（*）Enable Standard 25

Disable Standard 25

Note: Read the "Disable Standard 25" barcode will make the
scanner can not read the Standard 25 barcode. Thus, if the scanner
can not read the Standard 25 barcode, please trying to read "Enable
Standard 25" to reset.

For Example: Enable Standard 25.

1. Read the "Enter Setup" barcode;
2. Read the "Enable Standard 25" barcode;
3. Read the "Exit with Save" barcode.

Enter Setup

Exit with Save

Exit without Save

50

Downloaded from www.Manualslib.com manuals search engine

 3.6 Code 39
3.6.1 Enable/Disable Code 39
Decide whether or not to enable Code 39, The CT10X Scanner
defaults enable Code 39.

（*）Enable Code 39

Disable Code 39

3.6.2 START/STOP Transmission

Decide whether or not to include the start/stop characters in the data
being transmitted.

*Transmit Code 39 Start/Stop Characters

*Do Not Transmit Code 39 Start/Stop Characters

For example: Do Not Transmit Code 39 Start/Stop Characters.

1. Read the "Enter Setup" barcode;
2. Read the "Enable Code 39" barcode; (If Code 39is disabled, it
is need to set); 3. Read the "Do Not Transmit Code 39
Start/Stop Characters" barcode;
4. Read the "Exit with Save" barcode.

Enter Setup

Exit with Save

Exit without Save

51

Downloaded from www.Manualslib.com manuals search engine

 3.6.3 Checksum Verification
It is not enforced to include the checksum character in the Code 39
data. If checksum character is included, it should be the last
character of the barcode data. Checksum character is a calculate
value bases on all of the data, and is used to check the data is
correct or not.
Thus, if the scanner is set to "Do Not Verify", and the scanner will
output all the barcode data.
If the scanner is set to "Verify without Output Checksum Character",
and the scanner will check the data bases on the last character of
the barcode data. If the check passes, the scanner will output the
data without the checksum character; if the check not passes, the
scanner will display read failure.
If the scanner is set to "Verify with Output Checksum Character",
and the scanner will check the data bases on the last character of
the barcode data. If the check pass, the scanner will output the data
with the checksum character; if the check not pass, the scanner will
display read failure.

*Do Not Verify Verify without Output Checksum Character

Verify with Output Checksum Character

52

Downloaded from www.Manualslib.com manuals search engine

 3.6.4 Standard/Full ASCII Code 39
Decide whether or not to support Code 39 Full ASCII that includes
all the alphanumeric and special character. The CT10X Scanner
defaults full ASCII Code 39. It could disable full ASCII Code 39 via
set.

Disable Code 39 Full ASCII

* Enable Code 39 Full ASCII

Enter Setup

Exit with Save

Exit without Save

53

Downloaded from www.Manualslib.com manuals search engine

 3.7 Code 93
Decide whether or not to enable Code 93. The CT10X Scanner
defaults enable Code 93.

（*）Enable Code 93

Disable Code 93

Note: Read the "Disable Code 93" barcode will make the scanner
can not read the Code 93 barcode. Thus, if the scanner can not read
the Code 93 barcode, please trying to read "Enable Code 93" to
reset.

For Example: Enable Code 93.

1. Read the "Enter Setup" barcode;
2. Read the "Enable Code 93" barcode;
3. Read the "Exit with Save" barcode.

Enter Setup

Exit with Save

Exit without Save

54

Downloaded from www.Manualslib.com manuals search engine

 3.8 Code 128
Decide whether or not to enable Code 128. The CT10X Scanner
defaults enable Code 128.

（*）EnableCode128

Disable Code128

Note: Read the "Disable Code 128" barcode will make the scanner
can not read the Code 128 barcode. Thus, if the scanner can not
read the Code 128 barcode, please trying to read "Enable Code
128" to reset.

For Example: Disable Code 128.

1. Read the "Enter Setup" barcode;
2. Read the "Disable Code 128" barcode;
3. Read the "Exit with Save" barcode.

Enter Setup

Exit with Save

Exit without Save

55

Downloaded from www.Manualslib.com manuals search engine

 3.9 EAN-8
3.9.1 Enable/Disable EAN-8
Decide whether or not to enable EAN-8. The CT10X Scanner
defaults enable EAN-8.

（*）Enable EAN-8

Disable EAN-8

3.9.2 Convert to EAN-13

There is two ways for EAN-8 to change, convert to EAN-13, or add
"0" ahead of EAN-8, and the EAN-8 ID is not change.
Decide whether or not to convert to EAN-13, if EAN-8 convert to
EAN-13, it will be read as same as EAN-13. If add a "0" ahead of
EAN-8, and the EAN-8 ID is not change, the output ID is still EAN-8
ID.

Convert to EAN-13 Add "0" ahead and ID is not change

（*）Do not Convert

Enter Setup

Exit with Save

Exit without Save

56

Downloaded from www.Manualslib.com manuals search engine

 3.9.3 Checksum Transmission
Decide whether or not to transmit Checksum.

*Transmit EAN-8 Checksum

Do Not Transmit EAN-8 Checksum

For example: Enable EAN-8, and Convert to EAN-13.

1. Read the "Enter Setup" barcode;
2. Read the "Enable EAN-8" barcode;
3. Read the "Convert to EAN-13" barcode;
4. Read the "Exit with Save" barcode.

Enter Setup

Exit with Save

Exit without Save

57

Downloaded from www.Manualslib.com manuals search engine

 3.10 EAN-13
3.10.1 Enable/Disable EAN-13
Decide whether or not to read EAN-13. The CT10X Scanner
defaults enable EAN-13.

（*）Enable EAN-13

Disable EAN-13

3.10.2 Convert to ISBN

Decide whether or not to convert the EAN-13 to ISBN.

Convert EAN-13 to ISBN

* Do Not Convert EAN-13 to ISBN

Enter Setup

Exit with Save

Exit without Save

58

Downloaded from www.Manualslib.com manuals search engine

 3.10.3 Checksum Transmission
Decide whether or not to include the checksum character in the data
being transmitted.

*Transmit EAN-13 Checksum

Do Not Transmit EAN-13 Checksum

For example: Convert EAN-13 to ISBN.

* Read the "Enter Setup" barcode;
* Read the "Convert EAN-13 to ISBN" barcode;
* Read the "Exit with Save" barcode.

Enter Setup

Exit with Save

Exit without Save

59

Downloaded from www.Manualslib.com manuals search engine

 3.11 UPC-A
3.11.1 UPC-A Output “0”
Decide whether or not to add "0" in the output of UPC-A data.

（*）Enable EAN-13

Disable EAN-13

3.11.2 UPC-A Checksum Transmission

Decide whether or not to include the checksum character in the data
being transmitted.

Convert EAN-13 to ISBN

* Do Not Convert EAN-13 to ISBN

For example: UPC-A Output "0", Do Not Transmit UPC-A Checksum.

1. Read the "Enter Setup" barcode;
2. Read the "UPC-A Output "0"" barcode;
3. Read the "Do Not Transmit UPC-A Checksum" barcode;
4. Read the "Exit with Save" barcode.

Enter Setup

Exit with Save

Exit without Save

60

Downloaded from www.Manualslib.com manuals search engine

 3.12 UPC-E
3.12.1 Enable/Disable UPC-E
Decide whether or not to enable UPC-E. The CT10X Scanner
defaults enable UPC-E.

（*）Enable UPC-E

Disable UPC-E

3.12.2 UPC-E Checksum Transmission

Decide whether or not to include the checksum character in the data
being transmitted.

*Transmit UPC-E Checksum

Do Not Transmit UPC-E Checksum

Enter Setup

Exit with Save

Exit without Save

61

Downloaded from www.Manualslib.com manuals search engine

 3.13 MSI
Decide whether or not to enable MSI. The CT10X Scanner defaults
disable MSI.

Enable MSI

（*）Disable MSI

Note: Read the "Disable MSI" barcode will make the scanner can
not read the MSI barcode. Thus, if the scanner can not read the MSI
barcode, please trying to read "Enable MSI" to reset.

For example: Enable MSI.

1. Read the "Enter Setup" barcode;
2. Read the "Enable MSI" barcode;
3. Read the "Exit with Save" barcode.

Enter Setup

Exit with Save

Exit without Save

62

Downloaded from www.Manualslib.com manuals search engine

 4.1 CODE ID
Code ID List
Code Type Code ID Hex Value
Codabar a 61
Code 39 b 62
UPC-E c 63
EAN-13 d 64
Interleaved 2 of 5 (ITF) e 65
Code 2 of 5 (Standard) f 66
MSI g 67
Code 11 h 68
Code 93 i 69
Code 128 j 6A
Matrix 2 of 5 m 6D
2/5 Industrial n 6E
EAN-8 o 6F
ISBN k 6B
UPC-A l 6C

Decide whether or not to add Code ID in the barcode data of output.

Apply Output ID

（*）Ignore Output ID

For example: Apply Output ID.

1. Read the "Enter Setup" barcode;
2. Read the "Output ID" barcode;
3. Read the "Exit with Save" barcode;
Enter Setup

Exit with Save

Exit without Save

63

Downloaded from www.Manualslib.com manuals search engine

 4.2 Suffix Code of Barcode Settings
Decide whether or not to apply Enter for suffix of barcode data.

(*) Apply Enter for suffix Do not Apply Enter for suffix

Decide whether or not to apply Alt to suffix of barcode data.

（*）Apply Alt for suffix Do not Apply Alt for suffix

For example: Do not Apply Enter for suffix.

1. Read the "Enter Setup" barcode;
2. Read the "Do not Apply Enter for suffix" barcode;
3. Read the "Exit with Save" barcode.

Enter Setup

Exit with Save

Exit without Save

64

Downloaded from www.Manualslib.com manuals search engine

 APPENDIX I
The setting barcodes of parameters' value.

0 1

2 3

4 5

6 7

8 9

65

Downloaded from www.Manualslib.com manuals search engine

 Prefix and Suffix Setting
1. Scan the “Enter Setup” barcode

Enter setup

2. Scan the “Prefix Setting” or “Suffix Setting” scanner

Prefix Setting

Suffix Setting

3. Scan certain barcodes sequentially to generate your own

prefix/suffix. Example: If you want to add “#” as prefix or suffix,
according to the barcode list provided on our website, you need to
scan the “3” barcode first and then scan the “5” barcode.

0 1

2 3

66

Downloaded from www.Manualslib.com manuals search engine

 4 5

6 7

8 9

4. Scan the “Exit with Save” barcode.

Exit With save

67

Downloaded from www.Manualslib.com manuals search engine

 Prefix/Suffix number and symbol list
Number Symbol Number Symbol Number Symbol
32 space 64 @ 96 `
33 ! 65 A 97 a
34 “ 66 B 98 b
35 # 67 C 99 c
36 $ 68 D 100 d
37 % 69 E 101 e
38 & 70 F 102 f
39 ‘ 71 G 103 g
40 ( 72 H 104 h
41 ) 73 I 105 i
42 * 74 J 106 j
43 + 75 K 107 k
44 , 76 L 108 l
45 - 77 M 109 m
46 . 78 N 110 n
47 / 79 O 111 o
48 0 80 P 112 p
49 1 81 Q 113 q
50 2 82 R 114 r
51 3 83 S 115 s
52 4 84 T 116 t
53 5 85 U 117 u
54 6 86 V 118 v
55 7 87 W 119 w
56 8 88 X 120 x
57 9 89 Y 121 y
58 : 90 Z 122 z
59 ; 91 [ 123 {
60 < 92 \ 124 |
61 = 93 ] 125 }
62 > 94 ^ 126 ~
63 ? 95 _ 127 delete

68

Downloaded from www.Manualslib.com manuals search engine

 Contact Information
CHINA

CILICO MICROELECTRONICS LIMITED

Head office: #406, Building A, Huixin IBC,

Zhangba 1st Rd.,
Hi-tech Zone, Xi’an, China
Tel: 0086 18710380696

Shenzhen office: 3rd Floor, Building 6B,

Wu tong dao industrial park,
intersection road of Gushu Shunchang road
and Hangkong road, Xi'xiang street , Bao'an
district , Shenzhen, China

Tel: 0086 755 29120504

BRAZIL

SPARK
Tel.: +55 54-3242-4507
Phone hours: Weekdays 8 AM-6 PM (-3 GMT)
Email: [email protected]
Web: http://www.sparkag.com.br
Addr.: Rua Antônio Peruzzo, 250
Bairro: Sagrada Família – Nova Prata – RS
ZIP: 95320-000 - Brazil

69

Downloaded from www.Manualslib.com manuals search engine