Scribd
Upload
440 views1 page

HOFFMAN 751 Series: General Arrangement Flange Orientations

Uploaded by

Luis Fernando Bravo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
440 views1 page

HOFFMAN 751 Series: General Arrangement Flange Orientations

Uploaded by

Luis Fernando Bravo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

Dimensional Data

HOFFMAN 751 Series


Centrifugal Products
GENERAL ARRANGEMENT FLANGE ORIENTATIONS
12 HOLES: 7/8-9 THD INLET END VIEW OUTLET END VIEW
19.00 [483] DIA.
17.00 [432] DIA. BC
12.00 [305] DIA. 43.50 [1105]
13.50 [343]
12 HOLES: 7/8-9 THD
19.00 [483] DIA. 23.00
17.00 [432] DIA. BC [584]
12.00 [305] DIA.

52.12
[1324]

27.50
[698] 29.12
[740]
30.00
[762]
38.29 STANDARD STANDARD
[973] POSITION #1 POSITION #1

43.50 [1105]
13.50 [343]
LIFTING EARS
20.50
12" INLET 12" OUTLET [521]

ISOLATION BASE PADS: 13.44 52.12


Reference Only For [341]
F [1324]
Position & Quantity
29.12
[740]

R
M16

LEFT HAND TOP HORIZONTAL


POSITION #2 POSITION #2

43.50 [1105]
13.50 [343]

20.50
[521]

49.62
8.12 [1260]
[206]
29.12
Ø1.25 [32] 1.00 [25] THICK [740]
4 HOLES ISOLATION PADS
12.00
[305]
G
RIGHT HAND BOTTOM HORIZONTAL
A POSITION #3 POSITION #3

DIMENSIONAL DATA – inches [millimeters] WEIGHTS – lb [kg] & INERTIA – lb-ft2 [kg-m2]
2
FRAME A F G R FRAME PKG. LESS MOTOR BARE UNIT *WK
75102 84.00 [2134] 24.75 [629] 60.00 [1524] 10.25 [260] 75102 4050 [1837] 2550 [1157] 31 [1.31]
75103 84.00 [2134] 31.25 [794] 60.00 [1524] 10.25 [260] 75103 4450 [2018] 2950 [1338] 46 [1.95]
75104 108.00 [2743] 37.75 [959] 84.00 [2134] 10.25 [260] 75104 5050 [2291] 3350 [1520 62 [2.60]
75105 108.00 [2743] 44.25 [1124] 84.00 [2134] 10.25 [260] 75105 5450 [2472] 3750 [1701] 77 [3.25]
75106 114.00 [2896] 50.75 [1289] 90.00 [2286] 10.25 [260] 75106 5850 [2654] 4150 [1882] 92 [3.90]
75107 126.00 [3200] 57.25 [1454] 102.00 [2591] 10.25 [260] 75107 6300 [2858] 4600 [2087] 44 [1.83]

PRODUCT NOTES
1. Information is approximate, subject to change without notice, and not
for construction use unless certified
2. Position #1 is standard inlet & outlet orientation
3. A and G dimensions may vary depending on motor frame size
4. *Based on cast impellers except 75107 (fabricated impeller)
Gardner Denver Nash
PO Box 130, Bentleyville, PA 15314
Phone: +1 800-982-3009 / +1 724-239-1500
Fax: +1 724-239-1502 All Nash facilities are ISO 9001 certified.
E-mail: [email protected]
Web: www.HoffmanandLamson.com
01/2014 Page 1 of 1 CF1496121 Vs 06 © 2014 Gardner Denver, Inc.

You might also like