Preprocessing: Defining The Problem: Keypoint Coordinates (X, Y, Z)
Uploaded by
dsathiyaPreprocessing: Defining The Problem: Keypoint Coordinates (X, Y, Z)
Uploaded by
dsathiyahis tutorial was completed using ANSYS 7.
0 The purpose of the tutorial is to show the required
steps to account for the weight of an object in ANSYS.
Loads will not be applied to the beam shown below in order to observe the deflection caused by
the weight of the beam itself. The beam is to be made of steel with a modulus of elasticity of 200
GPa.
Preprocessing: Defining the Problem
1. Give example a Title
Utility Menu > File > Change Title ...
/title, Effects of Self Weight for a Cantilever Beam
2. Open preprocessor menu
ANSYS Main Menu > Preprocessor
/PREP7
3. Define Keypoints
Preprocessor > Modeling > Create > Keypoints > In Active CS...
K,#,x,y,z
We are going to define 2 keypoints for this beam as given in the following table:
Keypoint Coordinates (x,y,z)
1 (0,0)
2 (1000,0)
4. Create Lines
Preprocessor > Modeling > Create > Lines > Lines > In Active Coord
L,1,2
Create a line joining Keypoints 1 and 2
5. Define the Type of Element
Preprocessor > Element Type > Add/Edit/Delete...
For this problem we will use the BEAM3 (Beam 2D elastic) element. This
element has 3 degrees of freedom (translation along the X and Y axes, and
rotation about the Z axis).
6. Define Real Constants
Preprocessor > Real Constants... > Add...
In the 'Real Constants for BEAM3' window, enter the following geometric
properties:
i. Cross-sectional area AREA: 500
ii. Area moment of inertia IZZ: 4166.67
iii. Total beam height: 10
This defines a beam with a height of 10 mm and a width of 50 mm.
7. Define Element Material Properties
Preprocessor > Material Props > Material Models > Structural > Linear > Elastic
> Isotropic
In the window that appears, enter the following geometric properties for steel:
i. Young's modulus EX: 200000
ii. Poisson's Ratio PRXY: 0.3
8. Define Element Density
Preprocessor > Material Props > Material Models > Structural > Linear > Density
In the window that appears, enter the following density for steel:
i. Density DENS: 7.86e-6
9. Define Mesh Size
Preprocessor > Meshing > Size Cntrls > ManualSize > Lines > All Lines...
For this example we will use an element edge length of 100mm.
10. Mesh the frame
Preprocessor > Meshing > Mesh > Lines > click 'Pick All'
Solution Phase: Assigning Loads and Solving
1. Define Analysis Type
Solution > Analysis Type > New Analysis > Static
ANTYPE,0
2. Apply Constraints
Solution > Define Loads > Apply > Structural > Displacement > On Keypoints
Fix keypoint 1 (ie all DOF constrained)
3. Define Gravity
It is necessary to define the direction and magnitude of gravity for this problem.
o Select Solution > Define Loads > Apply > Structural > Inertia > Gravity...
o The following window will appear. Fill it in as shown to define an acceleration of
9.81m/s2 in the y direction.
Note: Acceleration is defined in terms of meters (not 'mm' as used throughout the
problem). This is because the units of acceleration and mass must be consistent to
give the product of force units (Newtons in this case). Also note that a positive
acceleration in the y direction stimulates gravity in the negative Y direction.
There should now be a red arrow pointing in the positive y direction. This
indicates that an acceleration has been defined in the y direction.
DK,1,ALL,0,
ACEL,,9.8
The applied loads and constraints should now appear as shown in the figure below.
4. Solve the System
Solution > Solve > Current LS
SOLVE
Postprocessing: Viewing the Results
1. Hand Calculations
Hand calculations were performed to verify the solution found using ANSYS:
The maximum deflection was shown to be 5.777mm
2. Show the deformation of the beam
General Postproc > Plot Results > Deformed Shape ... > Def + undef edge
PLDISP,2
As observed in the upper left hand corner, the maximum displacement was found to be
5.777mm. This is in agreement with the theortical value.
