Scribd
Upload
208 views

(From Is 875-Part 3) : Pxl/Aw

The document provides design details for intermediate span side girts of a building with dimensions of 50m x 150m x 6m. It includes input parameters for design like material properties, load intensities and section properties. Load calculations are performed and the girts are checked for bending stresses, shear stresses, combined bending and shear stresses as well as deflection as per relevant IS codes. The girts are found to be safe based on the design checks performed.

Uploaded by

Santosh Bapu
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
208 views

(From Is 875-Part 3) : Pxl/Aw

The document provides design details for intermediate span side girts of a building with dimensions of 50m x 150m x 6m. It includes input parameters for design like material properties, load intensities and section properties. Load calculations are performed and the girts are checked for bending stresses, shear stresses, combined bending and shear stresses as well as deflection as per relevant IS codes. The girts are found to be safe based on the design checks performed.

Uploaded by

Santosh Bapu
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

DESIGN OF INTERMEDIATE SPAN SIDE GIRT

JOB NO. 0.00 Rev. No.


OWNER 0.00 Date
CONSULTANT 0.00 Designed By
MAIN CONTRACTOR 0.00 Checked By
PROJECT 0.00 Recommded By
BUILDING 0.00 Approved By

INPUT FOR DESIGN


Width of the Building, B = 50 m
Length of the Building, D = 150 m
Height of the Building, H = 6 m
Bay Spacing,L = 7.50 m
Max. Purlin Spacing, Ps = 1.5 m
Dead Load Intensity, DL = 15 Kg/m2
Wind Load Intensity,WL = 132.54 Kg/m2
Interior Zone Pressure Co-eff for Wind = -0.9 (FROM IS 875-Part 3)
Yield Stress Of Steel, Fy = 345 Mpa
No. of sag Rods at Intermediate Girts = 3 A
Wind Load Intensity,WL for deflection 132.54
SECTIONAL PROPERTIES OF GIRTS:(AS PER CLAUSE 5.2 OF IS 801-1975)

TRY Z-200X1.8
t d b1 b2 L1 L2 D
Actual Sizes (As per Standard) 1.8 196.4 64 66 18 18 200
Effective Sizes for Stress Calc. 5.2.1 1.8 196.4 55 55 18 18 200
Effective Sizes for Deflection Calc. 5.2.1 1.8 196.4 64 64 18 18 200

Centre Of Gravity, Y = 10.01 cm Centre Of Gravity, X = 5.41 cm


4 4
Moment of Inertia, Ixx = 355.64 cm Moment of Inertia, Iyy = 35.55 cm
3 3
Sectional Modulus, Zxxtop = 35.54 cm Sectional Modulus, Zyyleft = 6.58 cm
3 3
Sectional Modulus, Zxxbot = 35.59 cm Sectional Modulus, Zyyright = 6.56 cm
2
Cross Sectional Area, A = 6.10 cm
4
Iyc, M.I. of compression flange about gravity axis= 17.71 cm cb = 1

Depth of Section = 200 mm (Cl. 6.3, IS:801- 1975)

a = 1.88 m

DESIGN OF INTERMEDIATE SPAN GIRTS: (AS PER IS 801-1975 & IS 800-2007)

LOAD CALCULATIONS:

Total Load, DL+LL Case DL x Ps = 22.50 Kg/m


Total Wind Load for strength (WL x Cp) x Ps = -178.93 Kg/m
Total Wind Load for deflection (WL x Cp) x Ps = -178.93 kg/m
Moment At Varoius Locations:
Maximum Span Moment, Mspan = 442 Kg-m
Maximum Span Moment over Sag Rod, Msag = 3.47 Kg-m
Maximum negative Moment near Support, Msupp = -866 Kg-m
Maximum moment capacity of Section, Mmax = 805 Kg-m
Moment at Lap, L1 0.385m from Support, ML1 = -758 Kg-m
Moment at Lap, L2 0.770m from Support, ML2 = -528 Kg-m
Moment at Lap, L3 1.155m from Support, ML3 = -324 Kg-m
Mnimum Lap Required = 385 mm
CHECK FOR SECTION FOR MOMENT AT MID SPAN = OK
CHECK FOR SECTION FOR MOMENT AT END SPAN = OK

ALLOWABLE STRESSES IN WEB OF GIRTS:(AS PER CLAUSE 6.4 OF IS 801-1975)

Shear stresses in Web:(Cl. 6.4.1, IS-801-1975)

d/t 109.111111 > 4590/√3450 78.1453495


Maximum average shear stress, Fv = 5850000/(d/t)² clause 6.4.1b

= 491.4 Kg/cm2 < 0.4 fy 1380 Kg/cm


2

Developed shear stress, fv, P x L / Aw = 379.6 Kg/cm2 SAFE

Bending Stress in Web: CLAUSE 6.4.2 PAGE 11 IS-801-1975

Maximum Bending stress, Fbw = 0.6 x Fy CLAUSE 6.1 & 6.4.2 IS-801-1975

= 2070.0 Kg/cm2

Allowable Compressive Stress in Extreme fibres in Flexure : CLAUSE 6.3 PAGE 11 IS-801-1975
Stress on the net section in compression on Extreme fibres= F = 0.6 x Fy (Cl 6.1, IS 801:1975)
= 2070 Kg/cm2
Allowable maximum stresses for laterally unbraced beams: CLAUSE 6.3 (b), IS-801-1975
Unsupported length L = a= = 1.88
L2 Sxc/(d Iyc) = 6421.04
0.18 π2 E cb/ fy = 1029.87
0.9 π2 E cb/ fy = 5149.36
Fb=0.3 π2 E cb d Iyc/(L2 Sxc) = 1703.2 Kg/cm2
Therefore, allowable compressive stress in extreme fibres in flexure = 2265.3

Developed Bending Stress Vertical Plane, Mspan / Zxmin = 1243.3 Kg/cm2 SAFE

Developed Bending Stress Inclined Plane, Msag / Zymin = 52.9 Kg/cm2 SAFE
Total Bending stress, fbw = 1296.2 Kg/cm2 SAFE

Combined Bending and Shear Stress in Web: clause 6.4.3 IS-801-1975


0.5
2 2
fbw fv SAFE
= 0.96
Fbw Fv

DEFLECTION CHECK : (AS PER CLAUSE 5.2.1.1 & TABLE 6 IN IS 800:2007)


Sectional Properties:

Centre Of Gravity, Y = 10.01 cm Centre Of Gravity, X = 6.28 cm


4
Moment of Inertia, Ixx = 386.85 cm Moment of Inertia, Iyy = 52.40
3
Sectional Modulus, Zxxtop = 38.63 cm Sectional Modulus, Zyyleft = 8.31
3 3
Sectional Modulus, Zxxbot = 38.74 cm Sectional Modulus, Zyyright = 8.34 cm
2
Cross Sectional Area, A = 6.42 cm Weight/m = 5.04 Kg.

Permissible Deflection, Span/150 = 50.0 mm

Maximum Deflection, 0.00218wL4/EI, (For Intermediate Span AS PER STAAD ANALYSIS)E=2X105

For DL = 14.8 mm SAFE

For WL = 16.0 mm SAFE

PROVIDE Z-200X1.8 INTERMEDIATE SPAN GIRT WITH A MINIMUM OVERLAP OF385 mm.

You might also like