PDU Description

Description

7/1551-LZA 701 6001/1-V1 Uen X

Copyright

© Ericsson AB 2019. All rights reserved. No part of this document may be

reproduced in any form without the written permission of the copyright owner.

Disclaimer

The contents of this document are subject to revision without notice due to
continued progress in methodology, design and manufacturing. Ericsson shall
have no liability for any error or damage of any kind resulting from the use of this
document.

7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09

 Contents

Contents

1 Product Overview 1
1.1 Purpose 1
1.2 Variants 1

2 Function Description 8
2.1 PDU 01 01 8
2.2 PDU 01 03 9
2.3 PDU 01 04 10
2.4 PDU 01 05 11
2.5 PDU 01 06 11
2.6 PDU 02 01 and PDU 02 02 12
2.7 Power Distribution Control 13

3 Technical Data 18

4 Signal and Power Interfaces 19

4.1 PDU 01 01 19
4.2 PDU 01 03 20
4.3 PDU 01 04 21
4.4 PDU 01 05 22
4.5 PDU 01 06 22
4.6 PDU 02 01 23
4.7 PDU 02 02 24

7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09

PDU Description

7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09

 Product Overview

1 Product Overview

This document describes the non-modular Power Distribution Units (PDUs).

For information on ECM PDUs, refer to PDU Description.

1.1 Purpose
The main function of the PDU is to distribute −48 V DC power to DC-powered
units. The PDU receives one feeding of input voltage and distributes the input
voltage to separate fused outputs through output connectors.

The PDUs are used for either internal or external power distribution.

1.2 Variants
Table 1 lists all PDU variants.

Table 1 PDU Variants

-48 V DC Type of Installation Power Distribution
PDU 01 01 Subrack mounted Supplying only Internal
Consumers
PDU 01 03 Subrack mounted Supplying both Internal
and External Consumers
PDU 01 04 Subrack mounted Supplying both Internal
and External Consumers
PDU 01 05 Subrack mounted Supplying only Internal
Consumers
PDU 01 06 Subrack mounted Supplying both Internal
and External Consumers
PDU 02 01 19-inch mounted Supplying only Internal
Consumers
PDU 02 02 19-inch mounted Supplying only Internal
Consumers

1.2.1 PDU 01 01
PDU 01 01 is only used for internal power distribution and is placed in a power
subrack.

7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09 1

 PDU Description

PDU 01 01 is available in two variants, either with R-state R4 or lower and with
R-state R5 or higher, where the R-state is the last part of the product number.

PDU 01 01, R-state R4

Figure 1 shows the front of PDU 01 01, R-state R4.

PDU 01 01
Fault Sys Volt
Test port
EC Bus
Oper

CB 1 CB 2 CB 3 CB 4 CB 5 CB 6 CB 7
H-UP <19A <16A <19A <16A <19A <16A
PCR PCR PCR PCR PCR PCR PCR

Ge0085C

Figure 1 PDU 01 01, R-state R4 Front

PDU 01 01, R-state R4, includes the following:

— One hold-up channel (output 1)

PDU 01 01, R-state R5

Figure 2 shows the front of PDU 01 01, R-state R5.

+ - PDU 01 01
Sys Volt
EC Test port

1 2 3 4 5 6 7

PCR PCR PCR PCR PCR PCR PCR

Ge0085D

Figure 2 PDU 01 01 R5 Front

PDU 01 01, R-state R5 offers the following new functions:

— Two hold-up channels (output 1 and 2)

— Yellow optical Power Distribution Fault indicator

— New front panel design

2 7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09

 Product Overview

— New optical indicator and new symbols introduced

For a more detailed functional description of PDU 01 01,see PDU 01 01 on page

8.

Note: PDU 01 03, PDU 01 04, PDU 01 05, and PDU 01 06, have no hold-up
channels.

1.2.2 PDU 01 03
PDU 01 03 is used for power distribution to both internal and external consumers.
Figure 3 shows the front of PDU 01 03.

+ - PDU 01 03
Sys Volt
EC Test port

PCR PCR PCR PCR PCR PCR

Ge1727A

Figure 3 PDU 01 03 Front

Note: PDU 01 03 has no hold-up channels.

1.2.3 PDU 01 04
PDU 01 04 is used for power distribution to both internal and external consumers.
Figure 4 shows the front of PDU 01 04.

PDU 01 04
EC Sys Volt
+ - Test port

PCR PCR PCR PCR PCR PCR

Ge1727D

Figure 4 PDU 01 04 Front

Note: PDU 01 04 has no hold-up channels.

7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09 3

 PDU Description

1.2.4 PDU 01 05
PDU 01 05 is used for internal power distribution and is placed in a power
subrack. Figure 5 shows the front of PDU 01 05.

PDU 01 05
1 ON OFF
1 2

2 ON OFF

Ge1727C

Figure 5 PDU 01 05 Front

Note: This PDU uses hydromagnetic circuit breakers, without E-Fuse

functionality. That is, there are no PCR functions at all in this PDU. It has
no hold-up channels.

1.2.5 PDU 01 06
PDU 01 06 is used for power distribution to both internal and external consumers
and is placed in a power subrack. Figure 6 shows the front of PDU 01 06.

PDU 01 06
ON

ON
I

EC

Ge8528B

Figure 6 PDU 01 06 Front

Note: This PDU uses hydromagnetic circuit breakers, without E-Fuse

functionality. That is, there are no PCR functions at all in this PDU. It has
no hold-up channels.

1.2.6 PDU 02 01
PDU 02 01 is used for power distribution to internal consumers and is placed in a
19 inch cabinet slot. Figure 7 and Figure 8 show PDU 02 01.

4 7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09

 Product Overview

11
PCR EC Bu
s
10
PCR
8
PCR 11

8
PCR 10

7 9
PCR
6 8
PCR
5 7
PC R
4
PCR 6

3 5
PCR
2
PC R 4

1 3
PCR
2

02 01 11
PC R
P DU

Ge0787A

Figure 7 PDU 02 01

Note: There are 11 Priority load, Cold-start, and Remote control (PCR)
switches under the switch cover on top of PDU 02 01 as shown in Figure
7.

PDU 02 01 includes two hold-up channels (output 1 and 2).

7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09 5

 PDU Description

PDU 02 01 1 2 3 4 5 6 7 8 9 10 11 EC Bus

1 11 EC Bus
PDU 02 01

Ge0714A

Figure 8 PDU 02 01 Front

1.2.7 PDU 02 02
PDU 02 02 is used for power distribution to internal consumers and is placed in a
19 inch cabinet slot. It is identical to PDU 02 01, except that it uses a different
cable connector and different mechanics for the 19 inch subrack. Figure 9 shows
PDU 02 02.

6 7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09

 Product Overview

11
PCR EC Bu
s
10
PCR
8
PCR 11

8
PCR 10

7 9
PCR
6 8
PCR
5 7
PC R
4
PCR 6

3 5
PCR
2
PC R 4

1 3
PCR
2

02 02 11
PC R
P DU

Ge1038A

Figure 9 PDU 02 02

Note: There are 11 PCR switches under the switch cover on top of PDU 02 02
as shown in Figure 9. It has no hold-up channels.

7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09 7

 PDU Description

2 Function Description

This section describes the functions for each PDU.

2.1 PDU 01 01
PDU 01 01 has the following functions:

— Power distribution control (see Power Distribution Control on page 13)

— System voltage measurement and power distribution supervision including

fuse status

— Fuse trip values selection (by hardware cable):

PDU 01 01, R-state R5: 6, 10 and 18 A

PDU 01 01, R-state R4: 6, 10, and 20 A

— System voltage test port

Figure 10 and Figure 11 show the block diagrams of PDU 01 01, R-state R5 and
PDU 01 01, R-state R4 with the maximum continuous current value.

System Voltage test port

2×14A with hold-up

(output 1 and 2)
Supervision
Control

EC bus

5×14A without hold-up

DC Input (output 3 to 7)

7×E-fuse

Ge0122D

Figure 10 PDU 01 01, R-state R5 Block Diagram

8 7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09

 Function Description

System Voltage test port

2×14A with hold-up

(output 1 and 2)

Supervision
Control
EC bus

5×14A without hold-up

DC Input (output 3 to 7)

7×E-fuse

Ge0122D

Figure 11 PDU 01 01, R-state R4 Block Diagram

2.2 PDU 01 03
PDU 01 03 has the following functions:

— 6 E-Fuse outputs

— Power distribution control (see Power Distribution Control on page 13)

— System voltage measurement

— Fuse trip values selection (by hardware cable): 6, 10, and 15 A

— System voltage test port

Figure 12 shows the block diagram of PDU 01 03 with the maximum continuous
current value.

7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09 9

 PDU Description

System Voltage Test Port

EC Bus Supervision
Control

6 x 12.5 A without hold-up

DC Input

6 x E-Fuse

Ge1728A

Figure 12 PDU 01 03 Block Diagram

2.3 PDU 01 04
PDU 01 04 has the following functions:

— 6 E-Fuse outputs

— Power distribution control (see Power Distribution Control on page 13)

— System voltage measurement

— Fuse trip values selection (by hardware cable): 6, 10, and 25 A

— System voltage test port

— Internal, and external DC distribution

Figure 13 shows the block diagram of PDU 01 04, with the maximum continuous
current value.

10 7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09

 Function Description

System Voltage Test Port

EC Bus Supervision
Control

6 x 20 A without hold-up
(output 1 to 6)
DC Input

6 x E-Fuse

Ge1728C

Figure 13 PDU 01 04 Block Diagram

2.4 PDU 01 05
PDU 01 05 has the following functions:

— Two outputs (circuit breaker)

— Circuit breaker trip value: 30 A

Figure 14 shows the block diagram of PDU 01 05 with the two circuit breakers.

DC Input 2 x 30 A without hold-up

(output 1 and 2)

2 x CB

Ge1728D

Figure 14 PDU 01 05 Block Diagram

2.5 PDU 01 06
PDU 01 06 has the following functions:

7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09 11

 PDU Description

— System voltage measurement

— Power distribution supervision

— Two outputs

— Circuit breaker trip value: 100 A

Figure 15 shows the block diagram of PDU 01 06 with the two circuit breakers.

Supervision
EC Bus
Control

DC Input 2 x 100 A without hold-up

2 x CB

Ge8678A

Figure 15 PDU 01 06 Block Diagram

2.6 PDU 02 01 and PDU 02 02

PDU 02 01 and PDU 02 02 have the following functions:

— 11 E-Fuse outputs

— System voltage measurement

— Power distribution control (see Power Distribution Control on page 13)

— Fuse trip values selection (by hardware cable): 6, 10, and 18 A

Figure 16 shows the block diagram of PDU 02 01 and PDU 02 02 with the
maximum continuous current value.

12 7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09

 Function Description

2 x14A With hold-up

(output 1 and 2)
Supervision
EC bus Control

DC Input

9 x14A Without hold-up

11xE Fuse
Ge0717B

Figure 16 PDU 02 01 and PDU 02 02 Block Diagram

2.7 Power Distribution Control

The power distribution in the non-modular PDUs can be configured by using PCR
functions. These functions can be enabled or disabled by using PCR switches on
the PDUs.

Note: Modular PDUs (ECMs) use software defined PCR settings. For more
information about these settings, for example, the Class Power
Distribution, refer to Managed Object Model (MOM). For more
information about ECMs, refer to PDU Description for PDU System.

2.7.1 PCR Switch Configuration

The non-modular PDUs have the following three PCR switches from left to right:

— Priority Load

— Cold Start

— Remote Control

7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09 13

 PDU Description

On

Off

Priority load Cold start Remote control

Ge9276C

Figure 17 PCR Switches

When a switch is set in the upper position, the PCR function is enabled (On), and
when a switch is set in the lower position, the function is disabled (Off).

After a change of state of one of the PCR-switches a software restart is required.

2.7.2 PCR Functions

This section describes the three PCR functions.

2.7.2.1 Priority Load Function

The PCR function Priority Load is related to the attribute

MainLoadUndervoltageDisconnect which defines the voltage level where Main
loads are disconnected while Prio loads remain on battery backup.

The Battery Fuse Unit (BFU) continuously monitors the systemVoltage. When
the battery voltage drops below the specified level,
MainLoadUndervoltageDisconnect, the BFU sends an action signal to the PDU.
When this signal is received, the PDU disconnects all outputs where the P switch
is set in position Off (disabled).

14 7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09

 Function Description

Cold-start signal Prio signal

PDU
(from SCU) (MainLoadDisconnect)

EC Bus Supervision
BFU
Control

DC Input
Battery
string

[n] x PCR [n] x E-Fuse

Ge10742C

Figure 18 BFU Action Signal to PDU

The P switch has the following settings:

On When the P switch is set in the upper (On) position, that is,
PriorityLoadenabled, the load connected to this output will be
disconnected when the systemVoltage is below
priorityLoadUndervoltageDisconnect.
Off When the P switch is set in the lower (Off) position, that is,
PriorityLoaddisabled, the load connected to this output will
be disconnected when the During battery backup, the RBS can
use two different voltage levels where the respective selected
loads are switched off.systemVoltage is below
mainLoadUndervoltageDisconnect.

During battery backup, the RBS can use two different voltage levels where the
respectiveAll units connected to the PDU ports set in the lower (Off) position
(defined as main loads) will be disconnected at the higher voltage level, defined
by attribute mainLoadUndervoltageDisconnect.

At the lower voltage level, defined by attribute

priorityLoadUndervoltageDisconnect, all units connected to the PDU ports
set in the upper (On) position are disconnected, as the battery is disconnected
from the power distribution system and the RBS -48 V system bus.

This feature can be used to disconnect less prioritized loads, such as radio units
which are not critical during the limited time when the batteries power the node.
This means that some services can be cut off earlier than others, for example:

— GSM lasting longer than WCDMA or LTE

— WCDMA lasting longer than LTE

7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09 15

 PDU Description

— Disconnect second radio in MIMO configurations and so on

A very common usage is to keep the DU and link transmission alive longer than
the radio service.

The climate system in the RBS requires that the SCU, and preferably the DU are
operational as both control the fans. Hence both SCU and DU are set to,
PriorityLoadenabled. If the SCU and the DU are not defined as priority loads,
that is their outputs are set to PriorityLoadenabled, the fans will stop running
when the MainLoadDisconnect level is reached. When this happens, the
remaining capacity in the battery cannot be used since no cooling is available.

2.7.2.2 Cold-Start Function

At startup, the PDU checks the input signal for the cold-start function. When
this signal is detected at startup, the PDU only turns on the outputs that are
enabled as cold outputs.

The cold-start signal is only read during startup.

The remaining outputs turn on when the cold-start signal ceases.

The C switch has the following settings:

On Meaning that cold-start is enabled.

Off Meaning that cold-start is disabled.

Note: For outdoor cabinets without heaters, all cold-start switches must be
enabled (upper position).

For outdoor cabinets equipped with heaters, the cold-start switches for
the following units should be enabled (upper position):
— SCU

— DC heater

— Loads outside the cabinet

2.7.2.3 Remote Control Function

The Baseband or DU can control the output when the switch in the PDU is
configured as remotely controllable. Both PDUs with PCR switches and modular
PDU variants can be controlled by software if the software supports remote
control of E-Fuses.

The R switch has the following settings:

On Meaning that the PDU output is remotely

controllable.

16 7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09

 Function Description

Off Meaning that the PDU output is not remotely

controllable.

Each distribution output is equipped with an E-Fuse function. The E-Fuse

function provides overload and short circuit protection.

Note: If the R switch is set to disabled, the output E-fuse cannot be remotely
controlled. The corresponding settings for software controlled PDUs ,
that is, ECM PDUs without PCR switches are managed by attribute
modifications in the MOM, refer to Managed Object Model (MOM).

2.7.3 Software Control

The position of each E-fuse PCR settings (enabled or disabled) can be retrieved
by using the MOM commands, refer to Managed Object Model (MOM).

When the R switch is set to the upper position (remoteControllable), the E-

Fuse can be controlled (ON or OFF) by the software, but only if the software
supports the remote control of the E-Fuses.

7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09 17

 PDU Description

3 Technical Data

Table 2 shows the technical data of the PDU variants.

Table 2 PDU Technical Data

Technica Normal Maximum Output Holdup Power Temperature Range Dimensions
l Data Voltage Continuo Capacity Function Dissipatio (°C)
Range us Continuo n
(V DC) Current us Load (W) Normal Limited Height Width Depth Weigh
(A) Performan (mm) (mm) (mm) t
ce (Manual (kg)
Control)
PDU 01 -39.5 125 4 × 16 A > 10 ms on 60 –40 to –40 to – 43 145 225 < 1.7
01 R4 to plus 3 x output for +60 10
-57.6 19 A CB1
PDU 01 -39.5 125 7 × 14 A > 10 ms for 60 –40 to –40 to – 43 145 225 < 1.7
01 R5 to Outputs 1 +60 10
-57.6 and 2
PDU 01 -39.5 75 6 × 12.5 A None 60 –40 to –40 to – 43 145 225 < 1.7
03 to +60 10
-58.5
PDU 01 -39.5 120 6 × 20 A None 60 –40 to –40 to – 43 145 225 < 1.7
04 to +60 10
-58.5
PDU 01 -39.5 200 2 × 100 A None 5 –40 to –40 to – 43 145 225 < 1.5
06 to +65 10
-58.5
PDU 02 -39.5 115 11 × 14 A > 10 ms on 60 –40 to –40 to – 21.4 434 200 <4
01 to DC output +60 10
-58.5 1 and 2
PDU 02 -39.5 115 11 × 14 A > 10 ms on 60 –40 to –40 to – 21.4 434 200 <4
02 to DC output +60 10
-58.5 1 and 2

18 7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09

 Signal and Power Interfaces

4 Signal and Power Interfaces

This section describes the interfaces on the PDU variants.

For information about the optical indicators, refer to Indicators, Buttons, and
Switches.

4.1 PDU 01 01
This section describes the interfaces on both revisions of PDU 01 01: R4 and R5.

4.1.1 PDU 01 01, R-state R5

This section describes the interfaces on PDU 01 01, R-state R5.

Table 3 lists details of the external interfaces on PDU 01 01, R-state R5.

Table 3 PDU 01 01, R-state R5 Interfaces

Marking Description (1) Connector Location

No marking Busbar connector Busbar Rear
Optical indicator, red N/A Front

Optical indicator, green N/A Front

Optical indicator, yellow N/A Front

EC EC bus RJ-45 Front

1, 2 DC out with hold-up; optical ET 20 A Front
indicator, green
3, 4, 5, 6, 7 DC out normal; optical ET 20 A Front
indicator, green
On/off button N/A Front

Sys Volt Test port for system voltage Hirschmann™ MBU 2, Front
Test port 931-337-000
P Priority load function switch Hardware selector Front
C Cold-start function switch Hardware selector Front
R Remote control function switch Hardware selector Front

7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09 19

 PDU Description

(1) For more details about optical indicators, refer to Indicators, Buttons, and Switches.

4.1.2 PDU 01 01, R-state R4

This section describes the interfaces on PDU 01 01, R-state R4.

Table 4 lists details of the external interfaces on PDU 01 01, R-state R4.

Table 4 PDU 01 01, R-state R4 Interfaces

Marking Description(1) Connector Location

No marking Busbar connector Busbar Rear
Fault Optical indicator, red N/A Front
Oper Optical indicator, green N/A Front
EC Bus EC bus RJ-45 Front
CB 1, H-UP DC out with hold-up; ET 20 A Front
Optical indicator, green
CB 2, CB 4, CB DC out without hold-up; ET 20 A Front
6, <19 A
Optical indicator, green
CB 3, CB 5, CB DC out normal; ET 20 A Front
7, <16 A
Optical indicator, green
On/off button N/A Front

Sys Volt Test port for system voltage Hirschmann MBU 2, Front
Test port 931-337-000
P Priority load function switch Hardware selector Front
C Cold-start function switch Hardware selector Front
R Remote control function switch Hardware selector Front
(1) For more details about optical indicators, refer to Indicators, Buttons, and Switches.

4.2 PDU 01 03
This section describes the interfaces on PDU 01 03.

Table 5 lists details of the external interfaces on PDU 01 03.

20 7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09

 Signal and Power Interfaces

Table 5 PDU 01 03 Interfaces

Marking Description (1) Connector Location

No marking Busbar connector Busbar Rear
Optical indicator, red N/A Front

Optical indicator, green N/A Front

EC EC bus RJ-45 Front

1–6 DC out without hold-up; ET 20 A Front
Optical indicator, green
On/off button N/A Front

Sys Volt Test port for system voltage Hirschmann MBU 2, Front
Test port 931-337-000
P Priority load function switch Hardware selector Front
C Cold-start function switch Hardware selector Front
R Remote control function switch Hardware selector Front
Optical indicator, green N/A Front

Optical indicator, yellow N/A Front

(1) For more details about optical indicators, refer to Indicators, Buttons, and Switches.

4.3 PDU 01 04
This section describes the interfaces on PDU 01 04.

Table 6 lists details of the external interfaces on PDU 01 04.

Table 6 PDU 01 04 Interfaces

Marking Description (1) Connector Location

No marking Busbar connector Busbar Rear
Optical indicator, red N/A Front

Optical indicator, green N/A Front

EC EC bus RJ-45 Front

1–6 DC out without hold-up; ET 20 A Front

7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09 21

 PDU Description

Marking Description (1) Connector Location

Optical indicator, green
On/off button N/A Front

Sys Volt Test port for system voltage Hirschmann MBU 2, Front
Test port 931-337-000
P Priority load function switch Hardware selector Front
C Cold-start function switch Hardware selector Front
R Remote control function switch Hardware selector Front
Optical indicator, green N/A Front

Optical indicator, yellow N/A Front

(1) For more details about optical indicators, refer to Indicators, Buttons, and Switches.

4.4 PDU 01 05
This section describes the interfaces on PDU 01 05.

Table 7 lists details of the external interfaces on PDU 01 05.

Table 7 PDU 01 05 Interfaces

Marking Description (1) Connector Location

No marking Busbar connector Busbar Rear
1–2 DC out without hold-up; Molex Mini-Fit® Front
Optical indicator, green
1 ON OFF On/off switch N/A Front
2 ON OFF

Optical indicators, green N/A Front

(1) For more details about optical indicators, refer to Indicators, Buttons, and Switches.

4.5 PDU 01 06
This section describes the interfaces on PDU 01 06.

Table 8 lists details of the external interfaces on PDU 01 06.

22 7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09

 Signal and Power Interfaces

Table 8 PDU 01 06 Interfaces

Marking Description (1) Connector Location

No marking Busbar connector Busbar Rear
Optical indicator, red N/A Front

Optical indicator, green N/A Front

Optical indicator, yellow N/A Front

EC EC bus RJ-45 Front

No marking Circuit breaker 100 A N/A Front
No marking DC out without hold-up Anderson SB 120 Front
(1) For more details about optical indicators, refer to Indicators, Buttons, and Switches.

4.6 PDU 02 01
This section describes the interfaces on PDU 02 01.

Table 9 lists details of the external interfaces on PDU 02 01.

Table 9 PDU 02 01 Interfaces

Marking Description (1) Connector Location

No marking Busbar connector Eaton Heinemann At the end of
the cable
20980-35/TP
Optical indicator, red N/A Front

Optical indicator, green N/A Front

EC Bus EC bus RJ-45 Front

1–2 DC out with hold-up; ET 20 A Front
Optical indicator, green
3–11 DC out without hold-up; ET 20 A Front
Optical indicator, green
On/off button N/A Front

P Priority load function switch Hardware selector Top

C Cold-start function switch Hardware selector Top

7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09 23

 PDU Description

Marking Description (1) Connector Location

R Remote control function switch Hardware selector Top
Optical indicator, green N/A Front

Optical indicator, yellow N/A Front

(1) For more details about optical indicators, refer to Indicators, Buttons, and Switches.

4.7 PDU 02 02
This section describes the interfaces on PDU 02 02.

Table 10 lists details of the external interfaces on PDU 02 02.

Table 10 PDU 02 02 Interfaces

Marking Description (1) Connector Location

No marking Busbar connector Anderson SB®120 At the end of
the cable
Optical indicator, red N/A Front

Optical indicator, green N/A Front

EC Bus EC bus RJ-45 Front

1–2 DC out with hold-up; ET 20 A Front
Optical indicator, green
3–11 DC out without hold-up; ET 20 A Front
Optical indicator, green
On/off button N/A Front

P Priority load function switch Hardware selector Top

C Cold-start function switch Hardware selector Top
R Remote control function switch Hardware selector Top
Optical indicator, green N/A Front

Optical indicator, yellow N/A Front

(1) For more details about optical indicators, refer to Indicators, Buttons, and Switches.

24 7/1551-LZA 701 6001/1-V1 Uen X | 2019-04-09