PRODUCT: PESD0603-140

ESD Protector
Overvoltage Protection Device DOCUMENT: SCD 26107
308 Constitution Drive
REV LETTER: K
Menlo Park, CA 94025-1164
REV DATE: DECEMBER 7, 2007
Phone: 800-227-4856 Raychem Circuit Protection Products PAGE NO.: 1 OF 7
www.circuitprotection.com

Specification Status: Released

Not to be used for new designs. For new designs please use PESD0603-240.

BENEFITS

• Suitable for high speed data transmission applications

• Board space savings
• Help to protect sensitive electronic circuits against damage from electrostatic discharge (ESD) events
• Assist equipment to pass IEC 61000-4-2, level 4 testing

FEATURES
• Thick film technology
• Low capacitance (0.25 pF typical)
• Low clamping voltage
• Capable of withstanding numerous ESD strikes
• Compatible with standard reflow installation procedures
• Bi-directional protection

APPLICATIONS

• Cellular phones

Caution: This part is not intended to be used under bias, nor for application with a power bus.

MATERIALS INFORMATION

ROHS Compliant ELV Compliant

PART NUMBERING

PESD 0603 - 140

Series Operating Voltage Designator
0
14 x 10 = 14VDC
EIA Size

The operating voltage is used to measure leakage current @ 1s

 PRODUCT: PESD0603-140
ESD Protector
Overvoltage Protection Device DOCUMENT: SCD 26107
308 Constitution Drive
REV LETTER: K
Menlo Park, CA 94025-1164
REV DATE: DECEMBER 7, 2007
Phone: 800-227-4856 Raychem Circuit Protection Products PAGE NO.: 2 OF 7
www.circuitprotection.com

TYPICAL DEVICE RATINGS AND CHARACTERISTICS

Typical
Typical
Typical IEC Typical Typical TLP Typical
TLP
IEC Clamping TLP Clamping Capacitance
Clamping
Trigger Voltage1 Trigger 2 Voltage2 @ 1 MHz,
Voltage
Voltage1 after Voltage2 after 60ns 1Vrms
after 30ns
30ns
Symbol VT(IEC) VC(IEC) VT(TLP) VC(TLP 30) VC(TLP 60) Cp
Unit V V V V V pF
Value 350 30 320 75 65 0.25
Note 1: IEC61000-4-2, level 4, 8kV contact test method
Note 2: TLP test method at 1000V (refer to graph on next page)
Note 3: PESD0603-140 can be used only in application without DC bias

GENERAL CHARACTERISTICS

Operating temperature: -55°C … + 110°C

Storage temperature: -40°C … + 85°C

ESD voltage capability (tested per IEC 61000-4-2)

o Contact discharge mode: typical 8kV, max 15kV

o Air discharge mode: typical 15kV, max 25kV

ESD pulse withstand: Typically 1,000 pulses (tested per IEC 61000-4-2, level 4, contact method)

Environmental Specifications
Heat
Thermal Solder Mechanical Solvent
Storage Solderability Vibration
Shock Heat Shock Resistance
Test
o 10 to
-55 C to
o o 50Hz,60s
125ºC 230 C±5 C 1500G,
o o cycle, IPA
Test 30min 110 C, 3±1s, 260 C, 0.5ms, X-Y-
2hrs ultrasonic
Conditions dwell 1000hours 95% 10s Z axis, 3
each in 300s
1000 coverage times
X-Y-Z
cycles
axis
Pass/Fail
IL≤10µA IL≤10µA IL≤10µA IL≤10µA IL≤10µA IL≤10µA IL≤10µA
Criteria
 PRODUCT: PESD0603-140
ESD Protector
Overvoltage Protection Device DOCUMENT: SCD 26107
308 Constitution Drive
REV LETTER: K
Menlo Park, CA 94025-1164
REV DATE: DECEMBER 7, 2007
Phone: 800-227-4856 Raychem Circuit Protection Products PAGE NO.: 3 OF 7
www.circuitprotection.com

TYPICAL TRANSMISSION LINE PULSE RESPONSE GRAPH

500.00

450.00

400.00

350.00

300.00
Voltage (V)

250.00

200.00

150.00

100.00

50.00

0.00
0.00 10.00 20.00 30.00 40.00 50.00 60.00 70.00 80.00 90.00 100.00
Time (ns)
 PRODUCT: PESD0603-140
ESD Protector
Overvoltage Protection Device DOCUMENT: SCD 26107
308 Constitution Drive
REV LETTER: K
Menlo Park, CA 94025-1164
REV DATE: DECEMBER 7, 2007
Phone: 800-227-4856 Raychem Circuit Protection Products PAGE NO.: 4 OF 7
www.circuitprotection.com

DIMENSIONS

D
A

Drawing Not To Scale

Length A Height B Terminal Width C Width D

MIN MAX MIN MAX MIN MAX MIN MAX
mm: 1.4 1.8 0.4 0.6 0.1 0.5 0.6 0.9
in*: (0.055) (0.071) (0.016) (0.024) (0.004) (0.02) (0.024) (0.035)

*Rounded off approximation

RECOMMENDED LAND PATTERN:

Solder thickness 0.15 to 0.2mm X

W X Y (Ref) Z
Min Max Min Max Min Max Min Max
mm: 0.9 1.0 0.5 0.6 1.0 1.1 2.7 2.8
in: * (0.035) (0.039) (0.020) (0.024) (0.039) (0.043) (0.106) (0.110)
*Rounded off approximation.
 PRODUCT: PESD0603-140
ESD Protector
Overvoltage Protection Device DOCUMENT: SCD 26107
308 Constitution Drive
REV LETTER: K
Menlo Park, CA 94025-1164
REV DATE: DECEMBER 7, 2007
Phone: 800-227-4856 Raychem Circuit Protection Products PAGE NO.: 5 OF 7
www.circuitprotection.com

SOLDER REFLOW RECOMMENDATIONS:

From ambient to
Temperature
A Preheating 30s to 60s
ramp up 1
temperature
B Preheating 140°C - 160°C 60s to 120s
From Preheating to
Temperature
C Main heating 20s to 40s
ramp up 2
temperature
at 200°C 60s ~ 70s
D Main at 220°C 50s ~ 60s
heating at 240°C 30s ~ 40s
at 260°C 5s ~ 10s
From main heating
E Cooling max 4°C/s
temperature to 100°C
 PRODUCT: PESD0603-140
ESD Protector
Overvoltage Protection Device DOCUMENT: SCD 26107
308 Constitution Drive
REV LETTER: K
Menlo Park, CA 94025-1164
REV DATE: DECEMBER 7, 2007
Phone: 800-227-4856 Raychem Circuit Protection Products PAGE NO.: 6 OF 7
www.circuitprotection.com

PACKAGING

Packaging Tape & Reel Standard Box

PESD0603-140 5,000 25,000

EIA referenced Reel Dimensions for PESD Devices

Reel Dimensions (mm):

A B C D E F G
0603 Devices 178.0 ±2.0 2.0 ±0.5 13.0±0.5 21.0±0.8 62.0±1.5 9.0±0.5 13.0±1.0

Carrier Dimensions (mm):

A B C D E F L W T1
0603 Devices 8.0±0.3 3.5±0.05 1.75±0.1 2.0±0.05 4.0±0.1 1.5±0.1 1.9±0.2 1.1±0.20 0.60±0.05

Product Orientation – always face up (meaning the substrate is at the bottom), but parts do not have
polarity mark.
Leader & Trailer: The leader is 180mm in length & consists of empty cavities with sealed cover tape.
The trailer is 350mm in length & consists of empty cavities with sealed cover tape.
 PRODUCT: PESD0603-140
ESD Protector
Overvoltage Protection Device DOCUMENT: SCD 26107
308 Constitution Drive
REV LETTER: K
Menlo Park, CA 94025-1164
REV DATE: DECEMBER 7, 2007
Phone: 800-227-4856 Raychem Circuit Protection Products PAGE NO.: 7 OF 7
www.circuitprotection.com

POST REFLOW, CLEANING CONDITIONS

A 5% saponofier combined with water during wash.

For Ultrasonic process water temperature should be at 50°C and board should be submerged for a minimum of
one minute in the solutions, then rinse and dry.

For in-line washing, the temperature of the water sprayed should be at 110°C, rinse and drying is done in-line.

Warning: Application Limitations for PESD0603-140. This part is not intended to be used
under bias, nor for power bus applications. Users should independently evaluate the
suitability of and test each product selected for their own applications

Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test
each product selected for their own applications. Tyco Electronics reserves the right to change or update, without notice, any
information contained in this publication; to change, without notice, the design, construction, processing, or specification of any
product; and to discontinue or limit production or distribution of any product. This publication supersedes and replaces all information
previously supplied. Without expressed or written consent by an officer of Tyco Electronics, Tyco Electronics does not authorize the
use of any of its products as components in nuclear facility applications, aerospace, or in critical life support devices or systems. Tyco
Electronics expressly disclaims all implied warranties regarding the information contained herein, including, but not limited to, any
implied warranties of merchantability or fitness for a particular purpose. Tyco Electronics’ only obligations are those in the Tyco
Electronics Standard Terms and Conditions of Sale and in no case will Tyco Electronics be liable for any incidental, indirect, or
consequential damages arising from the sale, resale, use, or misuse of its products.

© 2004, 2007 Tyco Electronics Corporation. All rights reserved.