KRUPP BAUTECHNIK

Spare Parts List

Hydraulic Hammer
HM 2500 Marathon

 
   

 
      !  

The    hydraulic hammer is equipped with a new wear

protection system comprising:

 
  
 "

The ”Vibrosilenced” and ”Marathon” models in the HM 2500 series can also
be supplied with the additional ”  ”
noise damping system.

 Spare Parts List

for Krupp Hydraulic Hammer

HM 2500 Marathon

 Krupp Berco Bautechnik GmbH

    

  

P. O. Box address: Postfach 102152 · D - 45021 Essen

Postal address: Helenenstrasse 149, D - 45143 Essen

Telephone: +49 201 633 - 02

Fax for after-sales service: +49 201 633 - 1352

Federal Republic of Germany


Instructions for use Instructions of order- Sample spare part
ing order:
   Please note the full identification For Krupp hydraulic hammer
This spare parts list contains no number of your HM 2500 Mara- 0371 -0 HM 2500 0016
safety regulations and is merely thon. This code can be found on
intended to assist in the ordering the cylinder ( part no.2 ) Hammer-No
of spare parts. Determine the quantity of individ- Hammer-type
For information on operating, ual parts which are required and Cylinder dimension index
servicing or repairing the need to be ordered. Cylinder No.
hammer, the relevant operating The order must indicate the fol-
manual must be consulted at all lowing details:
costs. 4 Tensioning bolts
Please observe the safety regu-
full identification code of the Pt.-Id.-No. 2263505
lations listed in the relevant oper- HM 2500 Marathon
ating manual.
required quantity

part ident. no.  
Krupp Berco Bautechnik GmbH
designation Please indicate the address to
which the parts should be sent
and the type of shipment re-
quired.

Working tools
ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ
ÂÂÂÂÂ
ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ ÂÂÂÂÂ
ÂÂÂÂÂ ÂÂÂÂÂÂ
ÂÂÂÂÂ
ÂÂÂÂÂÂ
ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ
ÂÂÂÂÂ
ÂÂÂÂÂ
ÂÂÂÂÂÂ
Description Useful length Weight Part ident.
[ mm ] [ kg ] no.

ÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂÂ
ÂÂÂÂÂ
  

ÂÂÂÂÂ
ÂÂÂÂÂÂ
840 264 3033099
Moil point
1060 308 3034027

840 179 3033891

Flat chisel
1060 324 3034096

Blunt steel 840 301 3035667

Further special designs available on request.

  Working steels will be subject to wear in the normal course of operations.
Replacement of these parts due to wear is  covered by the terms of the warranty.
(See corresponding operating instructions).

Krupp chisel paste 500 g cartridge, for ContiLube II . . . . . . . . . . . . . . . . Pt.-Id.-No. 3066065

Manual grease gun for cartridge ContiLube II . . . . . . . . . . . . . . . . . . . . . . Pt.-Id.-No. 3034567

Adapter kit for underwater applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pt.-Id.-No. 2262257

Main dimensions and weights

650 800



494 


690

Weight of the hammer with box

(as shown) 3612 kg

Required part-id.-nos for ordering

Part ident no. Description
3066175 Hydraulic hammer HM 2500 cpl. Marathon series
3067365 Hydraulic hammer HM 2500 cpl. Marathon series, with Vibrosilenced Plus noise damping


   
   
12

12 59 cpl.

84 cpl.

11 cpl.
1 cpl.

10 cpl.

CL

G
62 p

63

64
4 cpl
94

21 cpl.



30
25
2 cpl. 24 26

53

5 cpl. 52
47 49

51
47 49

52
34 53 X

Spare Parts List for Hydraulic Hammer HM 2500 Marathon
Part Part ident. Quantity Description Part Part ident. Quantity Description
no. no. no. no.

3067155 1 Hydraulic hammer 43 0478345 4 Threaded insert

HM 2500 Marathon 45 K 1331529 2 Locking bar
46 K 2262921 4 Sealing plug
1 3066094 1 Cylinder cover, cpl.
with parts 11, 17, 21, 28, 47 K 2260433 2 Locking bush
56-58, 62-64 and 73 49 K 2261540 2 Locking pin
2 3067159 1 Zylinder, vlst. 50 K 3032077 1 Wear bush
3 1356613 1 Percussion piston 51 K 3033729 1 Wear bush
4 3035233 1 Seal bushing cpl. 52 K 1854363 2 Locking bush
with parts 38-40 and 94 53 K 1854347 2 Locking pin
5 3066196 1 Lower hammer part, cpl. 55 1031529 6 Threaded insert
pre-assembled with parts
56 3067033 1 Control slide valve
27, 47, and 50-53
57 1331555 1 Control casing cover
6 2262675 4 Tensioning bolt
58 0103776 6 Cylindrical bolt
8 1852373 4 Plain washer
59 2269999 2 Swivel joint, cpl.
9 1852841 4 Nut with parts 77-83
10 2263505 4 Tensioning bolt, cpl.
60 K 0314373 2 O-ring
with parts 6, 8 and 9
61 0103750 12 Cylindrical bolt
11 3067157 1 Cylinder cover cpl.
with parts 18, 19, 62 3035453 1 AutoControl valve
43 and 55 63 K 0314370 1 O-ring
12 0206700 2 Lifting eye bolt 64 3035425 1 Threaded plug
13 1850102 1 Pressure accumulator 73 K 0314375 1 O-ring
14 1851591 4 Expansion bolt 77 2269861 2 Flange body
15 1851593 4 Plain washer 78 1356643 2 Connecting piece
17 1031794 1 Screw plug 79 K 1846282 4 O-ring
18 1844115 1 Threaded plug 80 K 1846281 4 Back-up ring
19 1844113 1 Perforated disk 81 1356645 2 Washer
20 K 1855001 2 Back-up ring 82 0028200 2 Locking ring
21 0996719 1 Filling valve cpl. 83 1353489 2 Screw cap
with part 92 84 K 1850422 1 Set of seals for swivel
22 K 2267589 8 Seal ring joint with parts 79 and 80
23 K 2267585 6 Seal ring 92 0478426 1 Screw plug
24 K 1846268 1 Slide ring seal 94 3033079 1 Seal bushing
25 K 1846278 1 O-ring X 3034265 1 Chisel stripper (see
26 K 3034283 1 Stripper spare parts list hydraulic
hammer compl..)
27 K 1851287 1 Buffer ring
- K 1329022 1 Diaphragm cpl.
28 K 0175125 1 O-ring for part no. 13
29 0921413 2 Dowel pin
- K 3066096 1 Set of seals, cpl.
30 K 3033525 1 Set of seals for grooved
rings
33 K 2267586 1 Seal ring
    K         
34 1329794 1 Protective plug
  
 
35 K 0314364 1 O-ring
36 K 0328046 1 Back-up ring Replacement of these parts due to wear is not
37 K 0314887 1 O-ring covered by the terms of the warranty.
38 K 1846267 2 Slide ring seal ( See corresponding operating instructions. )
39 K 1846278 2 O-ring
40 K 1846277 1 Quadring seal When ordering spare parts please do not forget to
42 K 1031810 1 O-ring state the tool ident. no.


Hydraulic hammer HM 2500 Marathon

121
122
202 123

101 120
209

102 50
203
204
205 208
206
207
105

100

1 103

202

201

X Y

Detail ’’ X ’’ Detail ’’ Y ’’ 2

111

113 114
Attachment to an existing carrier
requires an additional adapter 110 112
matching the carrier in question.

Spare Parts List for Hydraulic Hammer HM 2500 Marathon cpl.
Part No. Pt.-Id.-No. Quantity Designation

x 3067365 1 Hydraulic hammer HM 2500 Marathon cpl.

1 3067155 1 Hydraulic hammer HM 2500 Marathon

2 K 3034265 1 Chisel stripper
50 3067123 1 ContiLube Instruc-
tions)

Spare Parts List for Hammer box HM 2500 Marathon (Vibrosilenced series)
100 3067249 1 Hammer box HM 2500 Marathon cpl.
101 K 1356789 1 Elastic pad
102 K 1356925 2 Shock absorber
103 K 2269803 2 Plate (PUR)
105 K 2265215 2 Plate (PUR)
110 K 3033803 1 Floating ring
111 K 3033801 1 Counter ring
112 K 3033733 1 Guide ring
113 K 1854347 2 Locking bolt
114 K 1854363 2 Locking bolt bush
120 2261698 1 Transport safety device
121 1031739 2 Hexagonal socket head screw
122 0103255 2 Hexagonal nut
123 1853365 2 Lock washer
– 3066499 1 - Set of plastic parts 101 - 105

Additional parts for Hammer box HM 2500 Marathon (Vibrosilenced Plus series)
201 K 2267895 2 Sealing plug
202 K 2267899 10 Sealing plug
203 K 3031183 1 Cover
204 K 3032235 1 Cover, left
205 K 3068243 1 Cover, right
206 0433381 10 Hexagonal socket head screw
207 1850596 10 Lock washer
208 K 3031181 2 Cover plate
209 K 3068099 1 Cover plate

Contained in the adapter:

121 1031739 12 Hexagonal socket head screw

123 1853365 12 Lock washer

Parts marked with K will be subject to wear in the normal course of operations.

Replacement of these parts due to wear is  covered by the terms of the warranty.
( See corresponding operating instructions. )

When ordering spare parts please do not forget to state the tool ident. no.


When a hammer box assembly is ordered, a loose CE nameplate is included in the consignment in accord-
ance with European CE legislation. The weight stated on the adhesive nameplate refers to the weight of the
hydraulic hammer plus hammer box (not including connector and tool).
After the hydraulic hammer and the hammer box have been assembled the CE nameplate should be attached
to rear of the hammer box (see Section 3 of the operating manual). Only then may the complete unit be used.

Spare parts list, lubrication adapter kit for ContiLube II
Part No. Pt.-Id.-No. Quantity Designation

– x Adapter kit for ContiLube II

51 0026511 4 Hexagonal socket head screw

52 1850596 4 Lock washer
53 3066228 1 Angular screw coupling
54 3066233 1 Swivel screw coupling
55 K 3066224 1 Grease line
56 3066226 1 Angular screw coupling
57 3066234 1 Swivel screw coupling
58 K 3066051 1 Hydraulic hose

Parts marked with K will be subject to wear in the normal course of operations.
Replacement of these parts due to wear is  covered by the terms of the warranty.
( See corresponding operating instructions. )

When ordering spare parts please do not forget to state the tool ident. no.

        




51, 52
53 54 55 53

CL

P
G p

56 58 57 58 55

Important:

                     
                  





 KRUPP BAUTECHNIK
  
  

P. O. Box address: Postfach 102152
D - 45021 Essen

Postal address: Zollstrasse 68
D - 45356 Essen

Telephone: +49 201 633 - 02

Fax for after-sales service: +49 201 633 - 1352

Federal Republic of Germany