Sun Fire™ V890 Server

Owner’s Guide

Sun Microsystems, Inc.

www.sun.com

Part No. 817-3956-12

October 2005, Revision A

Submit comments about this document at: http://www.sun.com/hwdocs/feedback

Copyright 2005 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, California 95054, U.S.A. All rights reserved.
Sun Microsystems, Inc. has intellectual property rights relating to technology that is described in this document. In particular, and without
limitation, these intellectual property rights may include one or more of the U.S. patents listed at http://www.sun.com/patents, and one or
more additional patents or pending patent applications in the U.S. and in other countries.
This document and the product to which it pertains are distributed under licenses restricting their use, copying, distribution, and
decompilation. No part of the product or of this document may be reproduced in any form by any means without prior written authorization of
Sun and its licensors, if any.
Third-party software, including font technology, is copyrighted and licensed from Sun suppliers.
Parts of the product may be derived from Berkeley BSD systems, licensed from the University of California. UNIX is a registered trademark in
the U.S. and other countries, exclusively licensed through X/Open Company, Ltd.
Sun, Sun Microsystems, the Sun logo, AnswerBook2, docs.sun.com, Java, Sun Fire, SunCluster, UltraSPARC,VIS, OpenBoot, Solstice DiskSuite,
JumpStart, Sun StorEdge, SunSolve Online, SunVTS, and Solaris are trademarks, registered trademarks, or service marks of Sun Microsystems,
Inc. in the U.S. and other countries.
All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC International, Inc. in the U.S. and other
countries. Products bearing SPARC trademarks are based upon an architecture developed by Sun Microsystems, Inc.
The OPEN LOOK and Sun™ Graphical User Interface was developed by Sun Microsystems, Inc. for its users and licensees. Sun acknowledges
the pioneering efforts of Xerox in researching and developing the concept of visual or graphical user interfaces for the computer industry. Sun
holds a non-exclusive license from Xerox to the Xerox Graphical User Interface, which license also covers Sun’s licensees who implement OPEN
LOOK GUIs and otherwise comply with Sun’s written license agreements.
U.S. Government Rights—Commercial use. Government users are subject to the Sun Microsystems, Inc. standard license agreement and
applicable provisions of the FAR and its supplements.
DOCUMENTATION IS PROVIDED “AS IS” AND ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES,
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT,
ARE DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD TO BE LEGALLY INVALID.

Copyright 2005 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, Californie 95054, Etats-Unis. Tous droits réservés.
Sun Microsystems, Inc. a les droits de propriété intellectuels relatants à la technologie qui est décrit dans ce document. En particulier, et sans la
limitation, ces droits de propriété intellectuels peuvent inclure un ou plus des brevets américains énumérés à http://www.sun.com/patents et
un ou les brevets plus supplémentaires ou les applications de brevet en attente dans les Etats-Unis et dans les autres pays.
Ce produit ou document est protégé par un copyright et distribué avec des licences qui en restreignent l’utilisation, la copie, la distribution, et la
décompilation. Aucune partie de ce produit ou document ne peut être reproduite sous aucune forme, par quelque moyen que ce soit, sans
l’autorisation préalable et écrite de Sun et de ses bailleurs de licence, s’il y ena.
Le logiciel détenu par des tiers, et qui comprend la technologie relative aux polices de caractères, est protégé par un copyright et licencié par des
fournisseurs de Sun.
Des parties de ce produit pourront être dérivées des systèmes Berkeley BSD licenciés par l’Université de Californie. UNIX est une marque
déposée aux Etats-Unis et dans d’autres pays et licenciée exclusivement par X/Open Company, Ltd.
Sun, Sun Microsystems, le logo Sun, AnswerBook2, docs.sun.com, Java, Sun Fire, SunCluster, UltraSPARC,VIS, OpenBoot, Solstice DiskSuite,
JumpStart, Sun StorEdge, SunSolve Online, SunVTS, et Solaris sont des marques de fabrique ou des marques déposées de Sun Microsystems,
Inc. aux Etats-Unis et dans d’autres pays.
Toutes les marques SPARC sont utilisées sous licence et sont des marques de fabrique ou des marques déposées de SPARC International, Inc.
aux Etats-Unis et dans d’autres pays. Les produits portant les marques SPARC sont basés sur une architecture développée par Sun
Microsystems, Inc.
L’interface d’utilisation graphique OPEN LOOK et Sun™ a été développée par Sun Microsystems, Inc. pour ses utilisateurs et licenciés. Sun
reconnaît les efforts de pionniers de Xerox pour la recherche et le développement du concept des interfaces d’utilisation visuelle ou graphique
pour l’industrie de l’informatique. Sun détient une license non exclusive de Xerox sur l’interface d’utilisation graphique Xerox, cette licence
couvrant également les licenciées de Sun qui mettent en place l’interface d ’utilisation graphique OPEN LOOK et qui en outre se conforment
aux licences écrites de Sun.
LA DOCUMENTATION EST FOURNIE "EN L’ÉTAT" ET TOUTES AUTRES CONDITIONS, DECLARATIONS ET GARANTIES EXPRESSES
OU TACITES SONT FORMELLEMENT EXCLUES, DANS LA MESURE AUTORISEE PAR LA LOI APPLICABLE, Y COMPRIS NOTAMMENT
TOUTE GARANTIE IMPLICITE RELATIVE A LA QUALITE MARCHANDE, A L’APTITUDE A UNE UTILISATION PARTICULIERE OU A
L’ABSENCE DE CONTREFAÇON.

Please
Recycle
 Contents

Regulatory Compliance Statements xv

Declaration of Conformity xix

Safety Agency Compliance Statements xxi

Preface xxxiii

1. System Overview 1
About the Sun Fire V890 Server 1
Physical Enclosure 1
Processing Capability 2
System Memory 2
System I/O 2
FC-AL Storage Array 3
Other Peripherals 3
Ethernet Interfaces 4
Serial Ports and System Console 4
Monitoring and Management With Remote System Control Software 5
Power 5
Rackmounting Options 5

v
 Reliability, Availability, and Serviceability Features 6
Locating Front Panel Features 7
Locating Rear Panel Features 9
About the Status and Control Panel 11
LED Status Indicators 12
Power Button 13
Security Keyswitch 14
About Reliability, Availability, and Serviceability Features 15
Hot-Pluggable Disk Drives and PCI Cards 16
N+1 Power Supply Redundancy 16
Hot-Swappable Power Supplies 17
Redundant, Hot-Swappable Fan Trays 17
Environmental Monitoring and Control 17
Thermal Monitoring 18
Fan Monitoring 18
Power Subsystem Monitoring 18
Automatic System Recovery 19
Hardware Watchdog Mechanism 19
Remote System Control Software 20
Dual-Loop Enabled FC-AL Mass Storage Subsystem 20
Support for RAID Storage Configurations 21
Error Correction and Parity Checking 21
Status LEDs 21
Four Levels of Diagnostics 22

2. Setting Up the System 23

About the Parts Shipped to You 23
How to Install the Sun Fire V890 Server 24
Before You Begin 24

vi Sun Fire V890 Server Owner’s Guide • October 2005

 What to Do 24
About Setting Up a Console 30
How to Attach an Alphanumeric Terminal 31
Before You Begin 31
What to Do 31
What Next 32
How to Configure a Local Graphics Console 33
Before You Begin 33
What to Do 33
What Next 35
How to Power On the System 35
Before You Begin 35
What to Do 35
What Next 37
How to Power Off the System 38
What to Do 38
How to Initiate a Reconfiguration Boot 40
Before You Begin 40
What to Do 40
What Next 42
How to Redirect the System Console to RSC 42
Before You Begin 43
What to Do 43
What Next 44
How to Restore the Local System Console 45
Before You Begin 45
What to Do 45

3. Hardware Configuration 47

Contents vii
 About CPU/Memory Boards 48
About Memory Modules 51
Memory Interleaving 53
Independent Memory Subsystems 53
Configuration Rules 54
About PCI Cards and Buses 56
Configuration Rules 58
About the System Controller Card and RSC Software 59
Configuration Rule 60
About Power Supplies 61
Configuration Rules 63
About Fan Trays 64
Configuration Rules 66
About Removable Media Devices 67
About the Serial Ports 67
About the USB Ports 68
About Hardware Jumpers 69
About Serial Port Jumpers 70
About Flash PROM Jumpers 72
System I/O Board 72
FC-AL Disk Backplane 74

4. Mass Storage Subsystem Configuration 77

About FC-AL Technology 77
About Sun Fire V890 Mass Storage Features 79
About the Mass Storage Subsystem Components 80
About the FC-AL Disk Backplanes 82
Dual-Loop Configurations 83
Full vs. Split Backplane Configurations 83

viii Sun Fire V890 Server Owner’s Guide • October 2005

 Configuration Rules 84
About Internal Disk Drives 84
Configuration Rule 86
About FC-AL Host Adapters 86
Configuration Rules 87
About FC-AL Device Addresses 88

5. Configuring Network Interfaces 89

About Network Interfaces 90
About Redundant Network Interfaces 91
How to Configure the Primary Network Interface 92
Before You Begin 92
What to Do 92
What Next 93
How to Configure Additional Network Interfaces 94
Before You Begin 94
What to Do 94
What Next 96
How to Attach a Fiber-Optic Gigabit Ethernet Cable 97
Before You Begin 97
What to Do 98
What Next 99
How to Attach a Twisted-Pair Ethernet Cable 99
Before You Begin 99
What to Do 99
What Next 100
How to Select the Boot Device 101
Before You Begin 101
What to Do 101

Contents ix
 6. Configuring System Firmware 103
About OpenBoot Environmental Monitoring 104
Enabling or Disabling the OpenBoot Environmental Monitor 104
Automatic System Shutdown 105
OpenBoot Environmental Status Information 105
How to Enable OpenBoot Environmental Monitoring 106
Before You Begin 106
What to Do 106
How to Disable OpenBoot Environmental Monitoring 107
What to Do 107
How to Obtain OpenBoot Environmental Status Information 108
What to Do 108
About Automatic System Recovery 109
Auto-Boot Options 110
Error Handling Summary 111
Reset Scenarios 112
Normal Mode and Service Mode Information 112
ASR User Commands 113
How to Enable ASR 113
What to Do 113
How to Disable ASR 114
What to Do 114
About Manually Configuring Devices 114
Deconfiguring Devices vs. Slots 114
Deconfiguring All System Processors 115
Device Paths 115
How to Deconfigure a Device Manually 116
What to Do 116

x Sun Fire V890 Server Owner’s Guide • October 2005

 How to Reconfigure a Device Manually 117
What to Do 117
How to Obtain ASR Status Information 118
What to Do 118
About OpenBoot Emergency Procedures 119
Stop-A Functionality 119
Stop-D Functionality 119
Stop-F Functionality 120
Stop-N Functionality 120
How to Implement Stop-N Functionality 121
Before You Begin 121
What To Do 121
What Next 122
Reference for Device Identifiers 123

7. Server Administration 125

About Server Administration Software 125
About Hot-Pluggable and
Hot-Swappable Components 127
Fan Trays and Power Supplies 128
Disk Drives 129
PCI Cards 129
PCI Hot-Plug User Interfaces 130
For More Information 131
About Multipathing Software 131
For More Information 132
About Sun Management Center Software 132
For More Information 132
About Sun Remote System Control Software 133

Contents xi
 RSC Capabilities 133
RSC User Interfaces 134
For More Information 134
About Volume Management Software 134
Multipathing Software 135
RAID Concepts 135
Disk Concatenation 136
RAID 1: Disk Mirroring 136
RAID 0: Disk Striping 137
RAID 5: Disk Striping With Parity 137
Hot Spares (Hot Relocation) 137
About the Solaris luxadm Utility 138
For More Information 138
About Sun Cluster Software 139

8. LED Status Indicators 141

About CPU/Memory Slot LEDs 142
About PCI Slot LEDs 144
About Power Supply LEDs 148
About Fan Tray LEDs 152
About Disk Drive LEDs 156
About Gigabit Ethernet LEDs 159

9. Using Removable Media Storage Devices 161

About the DVD-ROM Drive 162
How to Insert a CD or DVD Into the Drive 162
What to Do 162
What Next 163
How to Eject a CD or DVD With Software Commands 164

xii Sun Fire V890 Server Owner’s Guide • October 2005

 Before You Begin 164
What to Do 164
What Next 165
How to Eject a CD or DVD Manually 165
Before You Begin 165
What to Do 165
What Next 166
How to Eject a CD or DVD in an Emergency 167
Before You Begin 167
What to Do 167
What Next 168
How to Clean a CD or DVD 168
Before You Begin 168
What to Do 169
What Next 169
About Tape Drives and Tape Cartridges 170
Handling and Storing Tape Cartridges 170
Thermal Conditioning 170
How to Insert a Tape Cartridge 171
What to Do 171
What Next 171
How to Remove a Tape Cartridge 172
Before You Begin 172
What to Do 172
What Next 172
How to Control a Tape Drive 173
What to Do 173
How to Clean a Tape Drive 173

Contents xiii
 Before You Begin 173
What to Do 173

A. Connector Pinouts 175

Reference for the Serial Port A and B Connectors 176
Serial Port Connector Diagram 176
Serial Port Signals 176
Reference for the USB Connectors 177
USB Connector Diagram 177
USB Connector Signals 177
Reference for the Twisted-Pair Ethernet Connector 178
TPE Connector Diagram 178
TPE Connector Signals 178
Reference for the System Controller Ethernet Connector 179
System Controller Ethernet Connector Diagram 179
System Controller Ethernet Connector Signals 179
Reference for the System Controller Serial Connector 180
System Controller Serial Connector Diagram 180
System Controller Serial Connector Signals 180

B. System Specifications 181

Reference for Physical Specifications 182
Reference for Electrical Specifications 182
Reference for Environmental Requirements 183
Reference for Agency Compliance Specifications 184
Reference for Clearance and Service Access Specifications 185

Index 187

xiv Sun Fire V890 Server Owner’s Guide • October 2005

 Regulatory Compliance Statements
Your Sun product is marked to indicate its compliance class:
• Federal Communications Commission (FCC) — USA
• Industry Canada Equipment Standard for Digital Equipment (ICES-003) — Canada
• Voluntary Control Council for Interference (VCCI) — Japan
• Bureau of Standards Metrology and Inspection (BSMI) — Taiwan
Please read the appropriate section that corresponds to the marking on your Sun product before attempting to install the
product.

FCC Class A Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy, and if it is
not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required
to correct the interference at his own expense.
Modifications: Any modifications made to this device that are not approved by Sun Microsystems, Inc. may void the authority
granted to the user by the FCC to operate this equipment.

FCC Class B Notice

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
Modifications: Any modifications made to this device that are not approved by Sun Microsystems, Inc. may void the authority
granted to the user by the FCC to operate this equipment.

xv
ICES-003 Class A Notice - Avis NMB-003, Classe A
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

ICES-003 Class B Notice - Avis NMB-003, Classe B

This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

xvi Sun Fire V890 Server Owner’s Guide • October 2005

BSMI Class A Notice
The following statement is applicable to products shipped to Taiwan and marked as Class A on the product compliance label.

CCC Class A Notice

The following statement is applicable to products shipped to China and marked with “Class A” on the product’s compliance
label.

GOST-R Certification Mark

Regulatory Compliance Statements xvii

xviii Sun Fire V890 Server Owner’s Guide • October 2005
 Declaration of Conformity
Compliance Model Number: 490
Product Family Name: Sun Fire V490

EMC
European Union
This equipment complies with the following requirements of the EMC Directive 89/336/EEC:
As Telecommunication Network Equipment (TNE) in both Telecom Centers and Other Than Telecom Centers per (as applicable):
EN300-386 V.1.3.1 (09-2001) Required Limits:
EN55022/CISPR22 Class A
EN61000-3-2 Pass
EN61000-3-3 Pass
EN61000-4-2 6 kV (Direct), 8 kV (Air)
EN61000-4-3 3 V/m 80-1000MHz, 10 V/m 800-960 MHz and 1400-2000 MHz
EN61000-4-4 1 kV AC and DC Power Lines, 0.5 kV Signal Lines,
EN61000-4-5 2 kV AC Line-Gnd, 1 kV AC Line-Line and Outdoor Signal Lines, 0.5 kV Indoor Signal Lines > 10m.
EN61000-4-6 3V
EN61000-4-11 Pass

As Information Technology Equipment (ITE) Class A per (as applicable):

EN55022:1998/CISPR22:1997 Class A
EN55024:1998 Required Limits:
EN61000-4-2 4 kV (Direct), 8 kV (Air)
EN61000-4-3 3 V/m
EN61000-4-4 1 kV AC Power Lines, 0.5 kV Signal and DC Power Lines
EN61000-4-5 1 kV AC Line-Line and Outdoor Signal Lines, 2 kV AC Line-Gnd, 0.5 kV DC Power Lines
EN61000-4-6 3V
EN61000-4-8 1 A/m
EN61000-4-11 Pass
EN61000-3-2:1995 + A1, A2, A14 Pass
EN61000-3-3:1995 Pass
Safety: This equipment complies with the following requirements of the Low Voltage Directive 73/23/EEC:
EC Type Examination Certificates:
EN 60950-1:2001 TÜV Rheinland Certificate No. S72040123
IEC 60950-1:2001 CB Scheme Certificate No. –on file–
Evaluated to all CB Countries
UL 60950-1, First Edition; CSA C22.2 No. 60950-00 File: E113363
FDA DHHS Accession Number (Monitor Only)
Supplementary Information: This product was tested and complies with all the requirements for the CE Mark .

/S/

Burt Hemp July 5, 2004 Donald Cameron July 5, 2004

Manager, Product Compliance Program Manager
Sun Microsystems, Inc. Sun Microsystems Scotland, Limited
One Network Circle, UBUR03-213 Blackness Road, Phase I, Main Bldg
Burlington, MA 01803 Springfield, EH49 7LR
USA Scotland, United Kingdom
Tel: 781-442-2118 Tel: +44 1 506 672 539
Fax: 781-442-1673 Fax: +44 1 506 670 011

xix
xx Sun Fire V890 Server Owner’s Guide • October 2005
Safety Agency Compliance Depending on the type of power switch your device has,
one of the following symbols may be used:
Statements
On – Applies AC power to the system.
Read this section before beginning any procedure. The
following text provides safety precautions to follow when
installing a Sun Microsystems product.
Off – Removes AC power from the system.

Safety Precautions
For your protection, observe the following safety Standby – The On/Standby switch is in the
precautions when setting up your equipment: standby position.
■ Follow all cautions and instructions marked on the
equipment.
■ Ensure that the voltage and frequency of your power Modifications to Equipment
source match the voltage and frequency inscribed on Do not make mechanical or electrical modifications to the
the equipment’s electrical rating label.
equipment. Sun Microsystems is not responsible for
■ Never push objects of any kind through openings in regulatory compliance of a modified Sun product.
the equipment. Dangerous voltages may be present.
Conductive foreign objects could produce a short
circuit that could cause fire, electric shock, or damage Placement of a Sun Product
to your equipment.
Caution – Do not block or cover the openings
Symbols of your Sun product. Never place a Sun
The following symbols may appear in this book: product near a radiator or heat register.
Failure to follow these guidelines can cause
overheating and affect the reliability of your
Caution – There is a risk of personal injury Sun product.
and equipment damage. Follow the
instructions.

Noise Level
Caution – Hot surface. Avoid contact. In compliance with the requirements defined in DIN 45635
Surfaces are hot and may cause personal Part 1000, the workplace-dependent noise level of this
injury if touched. product is less than 70 db(A).

Caution – Hazardous voltages are present. To

reduce the risk of electric shock and danger to
personal health, follow the instructions.

xxi
SELV Compliance The following caution applies only to devices with multiple
power cords:
Safety status of I/O connections comply to SELV
requirements.
Caution – For products with multiple power
cords, all power cords must be disconnected
Power Cord Connection to completely remove power from the system.

Caution – Sun products are designed to work

with power systems having a grounded
neutral (grounded return for DC-powered Battery Warning
products). To reduce the risk of electric shock,
do not plug Sun products into any other type Caution – There is danger of explosion if
of power system. Contact your facilities batteries are mishandled or incorrectly
manager or a qualified electrician if you are replaced. On systems with replaceable
not sure what type of power is supplied to batteries, replace only with the same
your building. manufacturer and type or equivalent type
recommended by the manufacturer per the
instructions provided in the product service
manual. Do not disassemble batteries or
Caution – Not all power cords have the same
attempt to recharge them outside the system.
current ratings. Do not use the power cord
Do not dispose of batteries in fire. Dispose of
provided with your equipment for any other
batteries properly in accordance with the
products or use. Household extension cords
manufacturer’s instructions and local
do not have overload protection and are not
regulations. Note that on Sun CPU boards,
meant for use with computer systems. Do not
there is a lithium battery molded into the real-
use household extension cords with your Sun
time clock. These batteries are not customer
product.
replaceable parts.

System Unit Cover

You must remove the cover of your Sun computer system
unit to add cards, memory, or internal storage devices. Be
sure to replace the cover before powering on your computer
system.

Caution – Do not operate Sun products

The following caution applies only to devices with a without the cover in place. Failure to take this
Standby power switch: precaution may result in personal injury and
system damage.
Caution – The power switch of this product
functions as a standby type device only. The
power cord serves as the primary disconnect
device for the system. Be sure to plug the
power cord into a grounded power outlet that
is nearby the system and is readily accessible.
Do not connect the power cord when the
power supply has been removed from the
system chassis.

xxii Sun Fire V890 Server Owner’s Guide • October 2005

Rack System Warning CD and DVD Devices
The following warnings apply to Racks and Rack Mounted The following caution applies to CD, DVD, and other
systems. optical devices.

Caution – For safety, equipment should Caution – Use of controls, adjustments, or the
always be loaded from the bottom up. That is, performance of procedures other than those
install the equipment that will be mounted in specified herein may result in hazardous
the lowest part of the rack first, then the next radiation exposure.
higher systems, etc.

Conformité aux normes de sécurité

Caution – To prevent the rack from tipping
during equipment installation, the anti-tilt bar Veuillez lire attentivement cette section avant de
on the rack must be deployed. commencer. Ce texte traite des mesures de sécurité qu’il
convient de prendre pour l’installation d’un produit Sun
Microsystems.

Caution – To prevent extreme operating

temperature within the rack insure that the Mesures de sécurité
maximum temperature does not exceed the Pour votre sécurité, nous vous recommandons de suivre
product’s ambient rated temperatures. scrupuleusement les mesures de sécurité ci-dessous lorsque
vous installez votre matériel:
■ Suivez tous les avertissements et toutes les
Caution – To prevent extreme operating instructions inscrites sur le matériel.
temperatures due to reduced airflow ■ Assurez-vous que la tension et la fréquence de votre
consideration should be made to the amount source d'alimentation correspondent à la tension et à
of air flow that is required for a safe operation la fréquence indiquées sur l'étiquette de la tension
of the equipment. électrique nominale du matériel
■ N'introduisez jamais d'objets quels qu'ils soient dans
les ouvertures de l'équipement. Vous pourriez vous
trouver en présence de hautes tensions dangereuses.
Laser Compliance Notice Tout objet étranger conducteur risque de produire un
Sun products that use laser technology comply with Class 1 court-circuit pouvant présenter un risque d'incendie
laser requirements. ou de décharge électrique, ou susceptible
d'endommager le matériel.

Symboles
Class 1 Laser Product Vous trouverez ci-dessous la signification des différents
Luokan 1 Laserlaite symboles utilisés:
Klasse 1 Laser Apparat
Laser Klasse 1
Attention – Vous risquez d'endommager le
matériel ou de vous blesser. Veuillez suivre les
instructions.

Attention – Surfaces brûlantes. Evitez tout

contact. Les surfaces sont brûlantes. Vous
risquez de vous blesser si vous les touchez.

Safety Agency Compliance Statements xxiii

 Connexion du cordon d’alimentation
Attention – Tensions dangereuses. Pour
réduire les risques de décharge électrique et
Attention – Les produits Sun sont conçus
de danger physique, observez les consignes
pour fonctionner avec des systèmes
indiquées.
d'alimentation équipés d'un conducteur
neutre relié à la terre (conducteur neutre pour
Selon le type d'interrupteur marche/arrêt dont votre produits alimentés en CC). Pour réduire les
appareil est équipé, l'un des symboles suivants sera utilisé: risques de décharge électrique, ne branchez
jamais les produits Sun sur une source
Marche – Met le système sous tension d'alimentation d'un autre type. Contactez le
alternative. gérant de votre bâtiment ou un électricien
agréé si vous avez le moindre doute quant au
type d'alimentation fourni dans votre
bâtiment.
Arret – Met le système hors tension
alternative.

Attention – Tous les cordons d'alimentation

ne présentent pas les mêmes caractéristiques
Veilleuse – L'interrupteur Marche/Veille est électriques. Les cordons d'alimentation à
sur la position de veille. usage domestique ne sont pas protégés contre
les surtensions et ne sont pas conçus pour être
utilisés avec des ordinateurs. N'utilisez jamais
Modification du matériel de cordon d'alimentation à usage domestique
N'apportez aucune modification mécanique ou électrique avec les produits Sun.
au matériel. Sun Microsystems décline toute responsabilité
quant à la non-conformité éventuelle d'un produit Sun L'avertissement suivant s'applique uniquement aux
modifié. systèmes équipés d'un interrupteur Veille:

Positionnement d’un produit Sun Attention – L'interrupteur d'alimentation de

ce produit fonctionne uniquement comme un
Attention – Evitez d'obstruer ou de recouvrir dispositif de mise en veille. Le cordon
les orifices de votre produit Sun. N'installez d'alimentation constitue le moyen principal de
jamais un produit Sun près d'un radiateur ou déconnexion de l'alimentation pour le
d'une source de chaleur. Si vous ne respectez système. Assurez-vous de le brancher dans
pas ces consignes, votre produit Sun risque de une prise d'alimentation mise à la terre près
surchauffer et son fonctionnement en sera du système et facile d'accès. Ne le branchez
altéré. pas lorsque l'alimentation électrique ne se
trouve pas dans le châssis du système.

L'avertissement suivant s'applique uniquement aux

Niveau de pression acoustique systèmes équipés de plusieurs cordons d'alimentation:
Le niveau de pression acoustique du lieu de travail définie
par la norme DIN 45 635 Part 1000 doit être au maximum de
70 db(A). Attention – Pour mettre un système équipé de
plusieurs cordons d'alimentation hors tension,
il est nécessaire de débrancher tous les
Conformité SELV cordons d'alimentation.
Le niveau de sécurité des connexions E/S est conforme aux
normes SELV.

xxiv Sun Fire V890 Server Owner’s Guide • October 2005

Mise en garde relative aux batteries
Attention – Afin d'éviter que le rack ne
penche pendant l'installation du matériel, tirez
Attention – Les batteries risquent d’exploser
la barre anti-basculement du rack.
en cas de manipulation maladroite ou de
remplacement incorrect. Pour les systèmes
dont les batteries sont remplaçables, effectuez
les remplacements uniquement selon le Attention – Pour éviter des températures de
modèle du fabricant ou un modèle équivalent fonctionnement extrêmes dans le rack,
recommandé par le fabricant, conformément assurez-vous que la température maximale ne
aux instructions fournies dans le manuel de dépasse pas la fourchette de températures
service du système. N’essayez en aucun cas de ambiantes du produit déterminée par le
démonter les batteries, ni de les recharger hors fabricant.
du système. Ne les jetez pas au feu. Mettez-les
au rebut selon les instructions du fabricant et
conformément à la législation locale en Attention – Afin d'empêcher des
vigueur. Notez que sur les cartes processeur températures de fonctionnement extrêmes
de Sun, une batterie au lithium a été moulée provoquées par une aération insuffisante,
dans l'horloge temps réel. Les batteries ne sont assurez-vous de fournir une aération
pas des pièces remplaçables par le client. appropriée pour un fonctionnement du
matériel en toute sécurité

Couvercle de l'unité
Pour ajouter des cartes, de la mémoire ou des périphériques Avis de conformité des appareils laser
de stockage internes, vous devez retirer le couvercle de Les produits Sun qui font appel aux technologies lasers sont
votre système Sun. Remettez le couvercle supérieur en conformes aux normes de la classe 1 en la matière.
place avant de mettre votre système sous tension.

Attention – Ne mettez jamais des produits

Sun sous tension si leur couvercle supérieur Class 1 Laser Product
n'est pas mis en place. Si vous ne prenez pas Luokan 1 Laserlaite
ces précautions, vous risquez de vous blesser Klasse 1 Laser Apparat
ou d'endommager le système. Laser Klasse 1

Mise en garde relative au système en rack

La mise en garde suivante s'applique aux racks et aux
Périphériques CD et DVD
systèmes montés en rack.
L'avertissement suivant s'applique aux périphériques CD,
DVD et autres périphériques optiques:
Attention – Pour des raisons de sécurité, le
matériel doit toujours être chargé du bas vers
le haut. En d'autres termes, vous devez Attention – L'utilisation de contrôles et de
installer, en premier, le matériel qui doit se réglages ou l'application de procédures autres
trouver dans la partie la plus inférieure du que ceux spécifiés dans le présent document
rack, puis installer le matériel sur le niveau peuvent entraîner une exposition à des
suivant, etc. radiations dangereuses.

Safety Agency Compliance Statements xxv

Einhaltung sicherheitsbehördlicher Je nach Netzschaltertyp an Ihrem Gerät kann eines der
folgenden Symbole verwendet werden:
Vorschriften
Lesen Sie vor dem Ausführen von Arbeiten diesen
Ein – Versorgt das System mit Wechselstrom.
Abschnitt. Im folgenden Text werden Sicherheitsvor-
kehrungen beschrieben, die Sie bei der Installation eines
Sun Microsystems-Produkts beachten müssen.
Aus– Unterbricht die Wechselstromzufuhr
zum Gerät.
Sicherheitsvorkehrungen
Treffen Sie zu Ihrem eigenen Schutz bei der Installation des
Geräts die folgenden Sicherheitsvorkehrungen:
Wartezustand – Der Ein-/Standby-Netz-
■ Beachten Sie alle auf den Geräten angebrachten schalter befindet sich in der Standby-Position.
Warnhinweise und Anweisungen.
■ Stellen Sie sicher, dass Spannung und Frequenz der
Stromversorgung den Nennleistungen auf dem am
Gerät angebrachten Etikett entsprechen. Modifikationen des Geräts
■ Führen Sie niemals Fremdobjekte in die Öffnungen Nehmen Sie keine elektrischen oder mechanischen
am Gerät ein. Es können gefährliche Spannungen Gerätemodifikationen vor. Sun Microsystems ist für die
anliegen. Leitfähige Fremdobjekte können einen Einhaltung der Sicherheitsvorschriften von modifizierten
Kurzschluss verursachen, der einen Brand, Strom- Sun-Produkten nicht haftbar.
schlag oder Geräteschaden herbeiführen kann.

Aufstellung von Sun-Geräten

Symbole
Die Symbole in diesem Handbuch haben folgende Achtung – Geräteöffnungen Ihres Sun-
Bedeutung: Produkts dürfen nicht blockiert oder
abgedeckt werden. Sun-Geräte sollten niemals
Achtung – Gefahr von Verletzung und in der Nähe von Heizkörpern oder Heißluft-
Geräteschaden. Befolgen Sie die Anwei- klappen aufgestellt werden. Die Nichtbeach-
sungen. tung dieser Richtlinien kann Überhitzung
verursachen und die Zuverlässigkeit Ihres
Sun-Geräts beeinträchtigen.
Achtung – Heiße Oberfläche. Nicht berühren,
da Verletzungsgefahr durch heiße Oberfläche
besteht. Lautstärke
Gemäß den in DIN 45 635 Teil 1000 definierten Vorschriften
beträgt die arbeitsplatzbedingte Lautstärke dieses Produkts
Achtung – Gefährliche Spannungen. Befolgen weniger als 70 dB(A).
Sie die Anweisungen, um Stromschläge und
Verletzungen zu vermeiden. SELV-Konformität
Der Sicherheitsstatus der E/A-Verbindungen entspricht
den SELV-Anforderungen.

xxvi Sun Fire V890 Server Owner’s Guide • October 2005

Anschluss des Netzkabels Warnung bezüglich Batterien

Achtung – Sun-Geräte sind für Achtung – Bei unsachgemäßer Handhabung

Stromversorgungssysteme mit einem oder nicht fachgerechtem Austausch der
geerdeten neutralen Leiter (geerdeter Batterien besteht Explosionsgefahr. Verwen-
Rückleiter bei gleichstrombetriebenen den Sie bei Systemen mit austauschbaren
Geräten) ausgelegt. Um die Gefahr von Batterien ausschließlich Ersatzbatterien
Stromschlägen zu vermeiden, schließen Sie desselben Typs und Herstellers bzw. einen
das Gerät niemals an andere Stromversor- entsprechenden, vom Hersteller gemäß den
gungssysteme an. Wenden Sie sich an den Anweisungen im Service-Handbuch des
zuständigen Gebäudeverwalter oder an einen Produkts empfohlenen Batterietyp. Versuchen
qualifizierten Elektriker, wenn Sie nicht sicher Sie nicht, die Batterien auszubauen oder
wissen, an welche Art von Stromversor- außerhalb des Systems wiederaufzuladen.
gungssystem Ihr Gebäude angeschlossen ist. Werfen Sie die Batterien nicht ins Feuer.
Entsorgen Sie die Batterien entsprechend den
Anweisungen des Herstellers und den vor Ort
Achtung – Nicht alle Netzkabel verfügen geltenden Vorschriften. CPU-Karten von Sun
über die gleichen Nennwerte. Herkömmliche, verfügen über eine Echtzeituhr mit integrier-
im Haushalt verwendete Verlängerungskabel ter Lithiumbatterie. Diese Batterie darf nur
besitzen keinen Überlastschutz und sind von einem qualifizierten Servicetechniker aus-
daher für Computersysteme nicht geeignet. gewechselt werden.
Verwenden Sie bei Ihrem Sun-Produkt keine
Haushalts-Verlängerungskabel.
Gehäuseabdeckung
Die folgende Warnung gilt nur für Geräte mit Standby- Sie müssen die Abdeckung Ihres Sun-Computersystems
Netzschalter: entfernen, um Karten, Speicher oder interne Speichergeräte
hinzuzufügen. Bringen Sie vor dem Einschalten des
Systems die Gehäuseabdeckung wieder an.
Achtung – Beim Netzschalter dieses Geräts
handelt es sich nur um einen Ein/Standby-
Schalter. Zum völligen Abtrennen des Systems Achtung – Nehmen Sie Sun-Geräte nicht ohne
von der Stromversorgung dient hauptsächlich Abdeckung in Betrieb. Die Nichtbeachtung
das Netzkabel. Stellen Sie sicher, dass das dieses Warnhinweises kann Verletzungen oder
Netzkabel an eine frei zugängliche geerdete Geräteschaden zur Folge haben.
Steckdose in der Nähe des Systems ange-
schlossen ist. Schließen Sie das Stromkabel
nicht an, wenn die Stromversorgung vom
Warnungen bezüglich in Racks eingebauter
Systemchassis entfernt wurde.
Systeme
Die folgenden Warnungen gelten für Racks und in Racks
Die folgende Warnung gilt nur für Geräte mit mehreren
eingebaute Systeme:
Netzkabeln:

Achtung – Aus Sicherheitsgründen sollten

Achtung – Bei Produkten mit mehreren Netz-
sämtliche Geräte von unten nach oben in
kabeln müssen alle Netzkabel abgetrennt wer-
Racks eingebaut werden. Installieren Sie also
den, um das System völlig von der Stromver-
zuerst die Geräte, die an der untersten
sorgung zu trennen.
Position im Rack eingebaut werden, gefolgt
von den Systemen, die an nächsthöherer Stelle
eingebaut werden, usw.

Safety Agency Compliance Statements xxvii

 Normativas de seguridad
Achtung – Verwenden Sie beim Einbau den
Kippschutz am Rack, um ein Umkippen zu Lea esta sección antes de realizar cualquier operación. En
vermeiden. ella se explican las medidas de seguridad que debe tomar al
instalar un producto de Sun Microsystems.

Achtung – Um extreme Betriebstemperaturen Medidas de seguridad

im Rack zu vermeiden, stellen Sie sicher, dass Para su protección, tome las medidas de seguridad
die Maximaltemperatur die Nennleistung der siguientes durante la instalación del equipo:
Umgebungstemperatur für das Produkt nicht
■ Siga todos los avisos e instrucciones indicados en el
überschreitet equipo.
■ Asegúrese de que el voltaje y frecuencia de la fuente
de alimentación coincidan con el voltaje y frecuencia
Achtung – Um extreme Betriebstemperaturen indicados en la etiqueta de clasificación eléctrica del
durch verringerte Luftzirkulation zu vermei- equipo.
den, sollte die für den sicheren Betrieb des ■ No introduzca objetos de ningún tipo por las rejillas
Geräts erforderliche Luftzirkulation eingesetzt del equipo, ya que puede quedar expuesto a voltajes
werden. peligrosos. Los objetos conductores extraños pueden
producir cortocircuitos y, en consecuencia, incendios,
descargas eléctricas o daños en el equipo.

Hinweis zur Laser-Konformität

Símbolos
Sun-Produkte, die die Laser-Technologie verwenden,
entsprechen den Laser-Anforderungen der Klasse 1. En este documento aparecen los siguientes símbolos:

Precaución – Existe el riesgo de que se

produzcan lesiones personales y daños en el
Class 1 Laser Product equipo. Siga las instrucciones.
Luokan 1 Laserlaite
Klasse 1 Laser Apparat
Laser Klasse 1 Precaución – Superficie caliente. Evite todo
contacto. Las superficies están calientes y
pueden causar lesiones personales si se tocan.

CD- und DVD-Geräte

Precaución – Voltaje peligroso. Para reducir
Die folgende Warnung gilt für CD-, DVD- und andere el riesgo de descargas eléctricas y lesiones
optische Geräte: personales, siga las instrucciones.

Achtung – Die hier nicht aufgeführte

Verwendung von Steuerelementen,
Anpassungen oder Ausführung von
Vorgängen kann eine gefährliche
Strahlenbelastung verursachen.

xxviii Sun Fire V890 Server Owner’s Guide • October 2005

En función del tipo de interruptor de alimentación del que Conexión del cable de alimentación
disponga el dispositivo, se utilizará uno de los símbolos
siguientes:
Precaución – Los productos Sun se han
diseñado para funcionar con sistemas de
Encendido – Suministra alimentación de CA alimentación que cuenten con un conductor
al sistema. neutro a tierra (con conexión a tierra de
regreso para los productos con alimentación
de CC). Para reducir el riesgo de descargas
Apagado – Corta la alimentación de CA del eléctricas, no conecte ningún producto Sun a
sistema. otro tipo de sistema de alimentación. Póngase
en contacto con el encargado de las
instalaciones de su empresa o con un
electricista cualificado en caso de que no esté
Espera – El interruptor de encendido/espera seguro del tipo de alimentación del que se
está en la posición de espera. dispone en el edificio.

Modificaciones en el equipo Precaución – No todos los cables de

No realice modificaciones de tipo mecánico ni eléctrico en el alimentación tienen la misma clasificación
equipo. Sun Microsystems no se hace responsable del eléctrica. Los alargadores de uso doméstico no
cumplimiento de normativas en caso de que un producto cuentan con protección frente a sobrecargas y
Sun se haya modificado. no están diseñados para su utilización con
sistemas informáticos. No utilice alargadores
de uso doméstico con el producto Sun.
Colocación de un producto Sun
La siguiente medida solamente se aplica a aquellos
Precaución – No obstruya ni tape las rejillas
dispositivos que dispongan de un interruptor de
del producto Sun. Nunca coloque un producto
alimentación de espera:
Sun cerca de radiadores ni fuentes de calor. Si
no sigue estas indicaciones, el producto Sun
podría sobrecalentarse y la fiabilidad de su Precaución – El interruptor de alimentación
funcionamiento se vería afectada. de este producto funciona solamente como un
dispositivo de espera. El cable de alimentación
hace las veces de dispositivo de desconexión
principal del sistema. Asegúrese de que
Nivel de ruido conecta el cable de alimentación a una toma
De conformidad con los requisitos establecidos en el de tierra situada cerca del sistema y de fácil
apartado 1000 de la norma DIN 45635, el nivel de ruido en acceso. No conecte el cable de alimentación si
el lugar de trabajo producido por este producto es menor de la unidad de alimentación no se encuentra en
70 db(A). el bastidor del sistema.

Cumplimiento de la normativa para

instalaciones SELV
Las condiciones de seguridad de las conexiones de entrada
y salida cumplen los requisitos para instalaciones SELV (del
inglés Safe Extra Low Voltage, voltaje bajo y seguro).

Safety Agency Compliance Statements xxix

La siguiente medida solamente se aplica a aquellos Advertencia sobre el sistema en bastidor
dispositivos que dispongan de varios cables de
Las advertencias siguientes se aplican a los sistemas
alimentación:
montados en bastidor y a los propios bastidores.

Precaución – En los productos que cuentan

Precaución – Por seguridad, siempre deben
con varios cables de alimentación, debe
montarse los equipos de abajo arriba. A saber,
desconectar todos los cables de alimentación
primero debe instalarse el equipo que se
para cortar por completo la alimentación
situará en el bastidor inferior; a continuación,
eléctrica del sistema.
el que se situará en el siguiente nivel, etc.

Advertencia sobre las baterías Precaución – Para evitar que el bastidor se

vuelque durante la instalación del equipo,
Precaución – Si las baterías no se manipulan debe extenderse la barra antivolcado del
o reemplazan correctamente, se corre el riesgo bastidor.
de que estallen. En los sistemas que cuentan
con baterías reemplazables, reemplácelas sólo
con baterías del mismo fabricante y el mismo
Precaución – Para evitar que se alcance una
tipo, o un tipo equivalente recomendado por
temperatura de funcionamiento extrema en el
el fabricante, de acuerdo con las instrucciones
bastidor, asegúrese de que la temperatura
descritas en el manual de servicio del
máxima no sea superior a la temperatura
producto. No desmonte las baterías ni intente
ambiente establecida como adecuada para el
recargarlas fuera del sistema. No intente
producto.
deshacerse de las baterías echándolas al fuego.
Deshágase de las baterías correctamente de
acuerdo con las instrucciones del fabricante y
las normas locales. Tenga en cuenta que en las Precaución – Para evitar que se alcance una
placas CPU de Sun, hay una batería de litio temperatura de funcionamiento extrema
incorporada en el reloj en tiempo real. Los debido a una circulación de aire reducida,
usuarios no deben reemplazar este tipo de debe considerarse la magnitud de la
baterías. circulación de aire requerida para que el
equipo funcione de forma segura.

Cubierta de la unidad del sistema

Debe extraer la cubierta de la unidad del sistema
Aviso de cumplimiento de la normativa para
informático Sun para instalar tarjetas, memoria o
la utilización de láser
dispositivos de almacenamiento internos. Vuelva a colocar Los productos Sun que utilizan tecnología láser cumplen los
la cubierta antes de encender el sistema informático. requisitos establecidos para los productos láser de clase 1.

Precaución – No ponga en funcionamiento

los productos Sun que no tengan colocada la
cubierta. De lo contrario, puede sufrir lesiones Class 1 Laser Product
personales y ocasionar daños en el sistema. Luokan 1 Laserlaite
Klasse 1 Laser Apparat
Laser Klasse 1

xxx Sun Fire V890 Server Owner’s Guide • October 2005

Dispositivos de CD y DVD
La siguiente medida se aplica a los dispositivos de CD y
DVD, así como a otros dispositivos ópticos:

Precaución – La utilización de controles,

ajustes o procedimientos distintos a los aquí
especificados puede dar lugar a niveles de
radiación peligrosos.

Nordic Lithium Battery Cautions

Norge

Advarsel – Litiumbatteri — Eksplosjonsfare.

Ved utskifting benyttes kun batteri som
anbefalt av apparatfabrikanten. Brukt batteri
returneres apparatleverandøren.

Sverige

Varning – Explosionsfara vid felaktigt

batteribyte. Använd samma batterityp eller en
ekvivalent typ som rekommenderas av
apparattillverkaren. Kassera använt batteri
enligt fabrikantens instruktion.

Danmark

Advarsel! – Litiumbatteri — Eksplosionsfare

ved fejlagtig håndtering. Udskiftning må kun
ske med batteri af samme fabrikat og type.
Levér det brugte batteri tilbage til
leverandøren.

Suomi

Varoitus – Paristo voi räjähtää, jos se on

virheellisesti asennettu. Vaihda paristo
ainoastaan laitevalmistajan suosittelemaan
tyyppiin. Hävitä käytetty paristo valmistajan
ohjeiden mukaisesti.

Safety Agency Compliance Statements xxxi

xxxii Sun Fire V890 Server Owner’s Guide • October 2005
Preface

The Sun Fire V890 Server Owner’s Guide answers your questions about setting up and
running the Sun Fire™ V890 server. Features and options, system setup and
installation, hardware configuration, and system administration topics for the
Sun Fire V890 server are covered in this manual.

This manual presents information in a modular format designed to answer the type
of questions that you might ask while installing, configuring, and using the
Sun Fire V890 server. Look at the titles of the modules and you’ll find the cue words
that direct you to the categories of questions and answers, such as:
■ How to . . . How do I do something?
■ About . . . Is there more information about this topic?
■ Reference for . . . Where can I find reference material for something?

You determine how much or how little of the information you need to read.

Using the table of contents or the task list on the first page of each chapter, you can
quickly find a specific topic or task. The information modules are brief; however,
they are interrelated and refer to other modules that you may want to read. For
instance, if you’re manually reconfiguring a device and you’re already familiar with
the task, you could go to “How to Reconfigure a Device Manually” and follow the
procedure. But if you need more background information before performing the
task, you should first read “About Manually Configuring Devices.”

xxxiii
 Using UNIX Commands
This document might not contain information on basic UNIX® commands and
procedures such as shutting down the system, booting the system, and configuring
devices. See one or more of the following for this information:
■ Solaris Handbook for Sun Peripherals
■ Documentation for the Solaris™ Operating System

Typographic Conventions
Typeface Meaning Examples

AaBbCc123 The names of commands, files, Edit your.login file.

and directories; on-screen Use ls -a to list all files.
computer output % You have mail.
AaBbCc123 What you type, when % su
contrasted with on-screen Password:
computer output
AaBbCc123 Book titles, new words or terms, Read Chapter 6 in the User’s Guide.
words to be emphasized These are called class options.
You must be superuser to do this.
AaBbCc123 Command-line variable; replace To delete a file, type rm filename.
with a real name or value

xxxiv Sun Fire V890 Server Owner’s Guide • October 2005

Shell Prompts
Shell Prompt

C shell machine-name%
C shell superuser machine-name#
Bourne shell and Korn shell $
Bourne shell and Korn shell superuser #

Third-Party Web Sites

Sun is not responsible for the availability of third-party web sites mentioned in this
document. Sun does not endorse and is not responsible or liable for any content,
advertising, products, or other materials that are available on or through such sites
or resources. Sun will not be responsible or liable for any actual or alleged damage
or loss caused by or in connection with the use of or reliance on any such content,
goods, or services that are available on or through such sites or resources.

Preface xxxv
 Related Documentation
Application Title

Installation Sun Fire V890 Server Rackmounting Guide

Sun Fire V490/V890 CPU/Memory Module Configuration
Guide
Installation Instructions for Solaris
Solaris (SPARC Platform Edition) Installation Guide
Solaris (SPARC Platform Edition) Installation Release Notes
Solaris Installation Guide
Solaris Advanced Installation Guide
Service Sun Fire V890 Server Service Manual
Late-Breaking Information Sun Fire V890 Server Product Notes
Solaris Release Notes
Solaris Release Notes Supplement for Sun Hardware
System Diagnostics Sun Fire V890 Diagnostics and Troubleshooting
SunVTS User’s Guide
SunVTS Test Reference Manual
SunVTS Quick Reference Card
System Management Sun Management Center Software Installation Guide
Sun Management Center Software User’s Guide
Sun Management Center Supplement for Workgroup Servers
Sun Management Center Software Release Notes
System Administration Solaris System Administrator Documentation
Platform Notes: The eri FastEthernet Device Driver
Platform Notes: The Sun GigabitEthernet Device Driver
Platform Notes: Using luxadm Software
Sun Fire V890 Dynamic Reconfiguration User’s Guide
OpenBoot 4.x Command Reference Manual
OpenBoot PROM Enhancements for Diagnostic Operation
OpenBoot 4.x Quick Reference
Remote System Monitoring Sun Remote System Control (RSC) User’s Guide
and Control

xxxvi Sun Fire V890 Server Owner’s Guide • October 2005

Accessing Sun Documentation
You can view, print, or purchase a broad selection of Sun documentation, including
localized versions, at:

http://www.sun.com/documentation

Contacting Sun Technical Support

If you have technical questions about this product that are not answered in this
document, go to:

http://www.sun.com/service/contacting

Sun Welcomes Your Comments

Sun is interested in improving its documentation and welcomes your comments and
suggestions. You can submit your comments by going to:

http://www.sun.com/hwdocs/feedback

Please include the title and part number of your document with your feedback:

Sun Fire V890 Server Owner’s Guide, part number 817-3956-12

Preface xxxvii
xxxviii Sun Fire V890 Server Owner’s Guide • October 2005
CHAPTER 1

System Overview

This chapter introduces you to the Sun Fire V890 server and describes some of its
features. The following information is covered in this chapter:
■ “About the Sun Fire V890 Server” on page 1
■ “Locating Front Panel Features” on page 7
■ “Locating Rear Panel Features” on page 9
■ “About the Status and Control Panel” on page 11
■ “About Reliability, Availability, and Serviceability Features” on page 15

About the Sun Fire V890 Server

The Sun Fire V890 server is a high-performance, shared memory, symmetric
multiprocessing server system that supports up to eight Sun UltraSPARC®
processors. The UltraSPARC processor incorporates a chip multithreading (CMT)
design featuring two threads on each physical processor. It implements the SPARC
V9 Instruction Set Architecture (ISA) and the Visual Instruction Set (VIS™)
extensions that accelerate multimedia, networking, encryption, and Java™
processing.

Physical Enclosure
The system is housed in a roll-around tower enclosure, which measures 28.1 inches
high, 18.9 inches wide, and 32.9 inches deep (71.4 cm x 48.0 cm x 83.6 cm). The
system has a maximum weight of 288 lb (130.6 kg).

1
 Processing Capability
Processing power is provided by up to four CPU/Memory boards. Each board
incorporates:
■ Two dual-threaded UltraSPARC processors
■ Local static random access memory (SRAM) external cache memory
■ Slots for 16 memory modules (eight per processor)

A fully configured system includes a total of eight UltraSPARC processors residing

on four CPU/Memory boards. For more information, see “About CPU/Memory
Boards” on page 48.

System Memory
System main memory is provided by up to 64 dual inline memory modules
(DIMMs), which operate at a 75-MHz clock frequency. A variety of DIMM capacities
are supported. For more information, see Sun Fire V490/V890 CPU/Memory Module
Configuration Guide, available at:
http://www.sun.com/products-n-solutions/hardware/docs/Servers/

Total system memory is shared by all processors in the system. Minimum and
mamimum depends on capacity of the DIMM modules. For more information about
system memory, see “About Memory Modules” on page 51.

System I/O
System I/O is handled by four separate Peripheral Component Interconnect (PCI)
buses. These industry-standard buses support all of the system’s on-board I/O
controllers in addition to nine slots for PCI interface cards. Seven of the PCI slots
operate at a 33-MHz clock rate, and two slots operate at either 33 or 66 MHz. All
slots comply with PCI Local Bus Specification Revision 2.1 and support PCI hot-plug
operations. You can hot-plug any standard PCI card, provided a suitable software
driver exists for the Solaris Operating System (Solaris OS) and the driver supports
PCI hot-plug operations. For additional details, see “About PCI Cards and Buses” on
page 56.

2 Sun Fire V890 Server Owner’s Guide • October 2005

FC-AL Storage Array
Internal disk storage is provided by up to 12 hot-pluggable, dual-ported Fibre
Channel-Arbitrated Loop (FC-AL) disk drives. The basic system includes a single
FC-AL disk backplane that accommodates up to six disk drives. An optional
expansion backplane can be added to accommodate an additional six disk drives.

In full backplane configuration, both backplanes provide dual-loop access to each of

the FC-AL disk drives. One loop is controlled by an on-board FC-AL controller
integrated into the system motherboard. The second loop is controlled by a PCI
FC-AL host adapter card (available as a system option). This dual-loop configuration
enables simultaneous access to internal storage via two different controllers, which
increases available I/O bandwidth to 200 Mbytes per second (versus 100 Mbytes per
second for single-loop configurations).

A dual-loop configuration can also be combined with multipathing software to

enhance hardware redundancy and failover capability. Should a component failure
render one loop inaccessible, the software can automatically switch data traffic to the
second loop to maintain system availability. For more information about the
system’s internal disk array, see “Mass Storage Subsystem Configuration” on
page 77.

It is possible to use the FC-AL subsystem in a split backplane configuration. For

details, see “Full vs. Split Backplane Configurations” on page 83, as well as the “Split
Backplane Configurations” appendix in the Sun Fire V890 Server Service Manual.

External multidisk storage subsystems and redundant array of independent disks

(RAID) storage arrays can be supported by installing single-channel or multichannel
PCI host adapter cards along with the appropriate system software. Software drivers
supporting SCSI, FC-AL, and other types of devices are included in the Solaris OS.

Other Peripherals
The Sun Fire V890 server provides front-panel access to three mounting bays. One
bay houses an IDE DVD-ROM drive, which is standard in all system configurations.
The other two bays accommodate an optional removable wide SCSI tape device,
which must be ordered separately. The tape drive option also requires a SCSI cable
and a SCSI adapter card, which must be ordered separately. You can easily convert
the two SCSI device bays into a single full-height bay by removing the metal shelf
divider. For additional details, see “About Removable Media Devices” on page 67.

Chapter 1 System Overview 3

 Ethernet Interfaces
The system provides two on-board Ethernet interfaces—one Gigabit Ethernet and
one Fast Ethernet interface. The Gigabit Ethernet interface operates at 1000 megabits
per second (Mbps). The Fast Ethernet interface can operate at 10 or 100 Mbps and
negotiates automatically with the remote end of the link (the link partner) to select a
common mode of operation.

Additional Ethernet interfaces or connections to other network types can be

provided by installing the appropriate PCI interface cards. Multiple network
interfaces can be combined with multipathing software to provide hardware
redundancy and failover capability. Should one of the interfaces fail, the software
can automatically switch all network traffic to an alternate interface to maintain
network availability. For more information about network connections, see
“Configuring Network Interfaces” on page 89.

Serial Ports and System Console

The Sun Fire V890 server provides two serial communication ports, which are
accessed through a single, shared DB-25 connector located on the system rear panel.
The primary port is capable of both synchronous and asynchronous communication,
while the secondary port is asynchronous only. An optional serial port splitter cable
is required to access the secondary serial port. For more information, see “About the
Serial Ports” on page 67.

The rear panel also provides two Universal Serial Bus (USB) ports for connecting
USB peripheral devices such as modems, printers, scanners, digital cameras, or a
Sun Type-6 USB keyboard and mouse. The USB ports support both isochronous
mode and asynchronous mode and enable data transmission at speeds of 1.5 and
12 Mbps. For additional details, see “About the USB Ports” on page 68.

The local system console device can be either a standard ASCII character terminal or
a local graphics console. The ASCII terminal connects to one of the system’s two
serial ports, while a local graphics console requires installation of a PCI graphics
card, monitor, USB keyboard, and mouse. You can also administer the system from a
remote workstation connected to the Ethernet or from a Sun Remote System Control
(RSC) console.

4 Sun Fire V890 Server Owner’s Guide • October 2005

Monitoring and Management With Remote
System Control Software
Remote System Control (RSC) is a secure server management tool that lets you
monitor and control your server over a serial port or a network connection. RSC
provides remote system administration for geographically distributed or physically
inaccessible systems. RSC software works in conjunction with the system controller
card included in all Sun Fire V890 servers. The system controller card runs
independently of the host server, and operates using 5-volt standby power from the
system’s power supplies. Together the hardware and software allow RSC to serve as
a “lights out” management tool that continues to function even when the server
operating system goes offline, or when the server is powered off.

Using RSC software, you can:

■ Access Solaris and OpenBoot™ PROM console functions remotely via the serial
and Ethernet ports on the system controller card
■ Run power-on self-test (POST) and OpenBoot Diagnostics from a remote console
■ Remotely monitor server environmental conditions, such as fan, temperature, and
power supply status, even when the server is offline
■ Perform remote server reboot, power-on, and power-off functions on demand

For additional details, see “About the System Controller Card and RSC Software” on
page 59 and “About Sun Remote System Control Software” on page 133.

Power
The basic system includes three 1629-watt output, 200–240-VAC input, power
supplies with internal fans. Two power supplies provide sufficient power for a
maximally configured system. The third power supply provides N+1 redundancy,
allowing the system to continue operating should any one of the power supplies fail.
Power supplies in a redundant configuration are hot-swappable, so that you can
remove and replace a faulty power supply without shutting down the operating
system or turning off the system power. For more information about the power
supplies, see “About Power Supplies” on page 61.

Rackmounting Options
The Sun Fire V890 server can be installed in any standard Electronic Industries
Association (EIA) 310-compliant 19-inch (48.3-cm) rack with at least 17 rack units
(29.8 inches, 75.6 cm) of available vertical mounting space and sufficient load-

Chapter 1 System Overview 5

 bearing capacity. An optional rackmounting kit is available for installing the server
into racks with depths ranging from 32 inches (81.3 cm) to 36 inches (91.4 cm).
Instructions for rackmounting the server are supplied with the rackmounting kit.

Reliability, Availability, and Serviceability Features

System reliability, availability, and serviceability (RAS) are significantly enhanced.
For more information about RAS features, see “About Reliability, Availability, and
Serviceability Features” on page 15.

6 Sun Fire V890 Server Owner’s Guide • October 2005

 Locating Front Panel Features
The illustration below shows the system features that are accessible from the front
panel with the front door open.

Power button Security keyswitch

DVD-ROM drive

Status and
control panel

Disk drives

Disk drive LEDs

For information about front panel controls and indicators, see “About the Status and
Control Panel” on page 11.

Chapter 1 System Overview 7

 Access to the system’s internal disk drives is through a large hinged door at the front
of the system. The front door features a keylock for added security. When the key is
in the horizontal position, the door is unlocked. Make sure that the key is in the
horizontal position before you close the door. To prevent unauthorized access to the
disk drives, lock the door by turning the key 90 degrees counterclockwise and
remove the key.

Note – The same key operates the front panel keyswitch and the locks on the front
and side doors.

8 Sun Fire V890 Server Owner’s Guide • October 2005

 Locating Rear Panel Features
The following figure shows the system features that are accessible from the rear
panel.

SC Gigabit
PCI slot 8
Ethernet interface
PCI slot 7
PCI slot 6
PCI slot 5
PCI slot 4
PCI slot 3
PCI slot 2
PCI slot 1
USB B PCI slot 0

USB A
TPE Fast
Ethernet
Serial port A/B interface
System controller
card
Grounding screw

Power supply 0
Power supply 2

Power supply 1

Chapter 1 System Overview 9

 The three power supplies are accessible from the system rear panel. Each power
supply has three LED indicators for displaying power status and fault conditions.
See “About Power Supply LEDs” on page 148 for additional details.

A grounding screw is located just above the center power supply. When installing a
Sun Fire V890 server into a rack, or connecting the server to an external storage
array, be sure to connect an appropriate grounding strap between the server’s
grounding screw and the grounding screw on the rack enclosure or external storage
array. A grounding strap prevents ground loops between systems and peripherals
and helps guard against possible data loss.

10 Sun Fire V890 Server Owner’s Guide • October 2005

 About the Status and Control Panel
The system status and control panel includes several LED status indicators, a Power
button, and a security keyswitch. The following figure shows the status and control
panel.

System Fault LED

Power/OK LED OK-to-Remove LED

Power button
Security keyswitch

Power Fault

Attention Attention
Left Side Right Side

Thermal Thermal
Fault Fault

Disk Fault

Chapter 1 System Overview 11

 LED Status Indicators
Several LED status indicators provide general system status, alert you to system
problems, and help you to determine the location of system faults.
■ At the top of the status and control panel, three general status LEDs provide a
snapshot of the system status.
■ Below the Power button and security keyswitch, a graphical display provides
additional LED icons to indicate specific fault conditions and locations.

The general status LEDs work in conjunction with the specific fault LED icons. For
example, a fault in the disk subsystem illuminates both the System Fault LED at the
top of the panel and the Disk Fault icon in the graphical display below it. Fault LEDs
within the enclosure help pinpoint the location of the faulty device. Since all front
panel status LEDs are powered by the system’s 5-volt standby power source, fault
LEDs remain lit for any fault condition that results in a system shutdown. For more
information about LED indicators on the rear panel and inside the enclosure, see
“LED Status Indicators” on page 141.

During system startup, the front panel LEDs are individually toggled on and off to
verify that each one is working correctly. After that, the front panel LEDs operate as
described in the following table.

Name Icon Description

Power/OK This green LED lights when the system power is on.

System Fault This amber LED lights to indicate a serious system fault.
When this LED is lit, one or more icons in the display panel
may also light to indicate the specific nature and location of
the fault.

OK-to- This amber LED lights to indicate that an internal

Remove hot-pluggable component is ready for removal.

Disk Fault This amber LED lights to indicate a serious disk subsystem
fault that is likely to bring down the system. When this
LED is lit, one or more disk LEDs may also be lit at the
front of the disk cage, indicating the source of the fault. See
“About Disk Drive LEDs” on page 156.

12 Sun Fire V890 Server Owner’s Guide • October 2005

Name Icon Description

Power Fault This amber LED lights to indicate a serious power

subsystem fault that is likely to bring down the system.
When this LED is lit, one or more power supply LEDs may
also be lit on the system rear panel. See “About Power
Supply LEDs” on page 148.

Thermal Fault This amber LED lights to indicate a serious thermal fault
(fan fault or overtemperature condition) that is likely to
bring down the system. There are two Thermal Fault LEDs
in the display to indicate whether the fault is located on the
left or right side of the system. In the event of a fan fault, a
fault LED inside the system will indicate the faulty fan
assembly. See “About Fan Tray LEDs” on page 152.
Attention This amber LED lights to indicate that an internal
Left Side component on the left side of the system requires servicing.

Attention This amber LED lights to indicate that an internal

Right Side component on the right side of the system requires
servicing.

Power Button
The system Power button is recessed to prevent accidentally turning the system on
or off. The ability of the Power button to turn the system on or off is controlled by
the security keyswitch.

If the operating system is running, pressing and releasing the Power button initiates
a graceful software system shutdown. Pressing and holding in the Power button for
five seconds causes an immediate hardware shutdown.

Caution – Whenever possible, you should use the graceful shutdown method.
Forcing an immediate hardware shutdown may cause disk drive corruption and loss
of data. Use this method only as a last resort.

Chapter 1 System Overview 13

 Security Keyswitch
The four-position security keyswitch controls the power-on modes of the system and
prevents unauthorized users from powering off the system or reprogramming
system firmware. The following table describes the function of each keyswitch
setting.

Position Icon Description

Normal This setting enables the system Power button to power the
system on or off. If the operating system is running, pressing
and releasing the Power button initiates a graceful software
system shutdown. Pressing and holding the Power button in
for five seconds causes an immediate hardware power off.
Locked The Locked setting:
• Disables the system Power button to prevent unauthorized
users from powering the system on or off
• Disables the keyboard Stop-A command, terminal Break key
command, ~# tip window command, and RSC break
command, preventing users from suspending system
operation to access the system ok prompt
• Prevents unauthorized programming of the system flash
PROMs
The Locked position is the recommended setting for normal
day-to-day operations.
Diagnostics This setting puts the system into service mode, forcing power-
on self-test (POST) and OpenBoot Diagnostics software to run
at a Sun prescribed level during system startup and system
resets. The Power button functions the same as when the
keyswitch is in the Normal position.

Forced Off This setting forces the system to power off immediately and
enter 5-volt standby mode. It also disables the system Power
button. You may want to use this setting when AC power is
interrupted and you do not want the system to restart
automatically when power is restored. With the keyswitch in
any other position, if the system was running prior to losing
power, it restarts automatically once power is restored.

The Forced Off setting also prevents an RSC console from

restarting the system. However, the system controller card
continues to operate using the system’s 5-volt standby power.

14 Sun Fire V890 Server Owner’s Guide • October 2005

About Reliability, Availability, and
Serviceability Features
Reliability, availability, and serviceability (RAS) are aspects of a system’s design that
affect its ability to operate continuously and to minimize the time necessary to
service the system. Reliability refers to a system’s ability to operate continuously
without failures and to maintain data integrity. System availability refers to the
percentage of time that a system remains accessible and usable. Serviceability relates
to the time it takes to restore a system to service following a system failure. Together,
reliability, availability, and serviceability features provide for near continuous
system operation.

To deliver high levels of reliability, availability, and serviceability, the Sun Fire V890
system offers the following features:
■ Hot-pluggable disk drives and PCI cards
■ N+1 power supply redundancy
■ Hot-swappable power supplies
■ Redundant, hot-swappable fan trays
■ Environmental monitoring and fault protection
■ Automatic system recovery (ASR) capabilities
■ Hardware watchdog mechanism
■ Remote System Control (RSC) remote “lights out” management capability
■ Support for disk and network multipathing with automatic failover capability
■ Dual-loop enabled FC-AL mass storage subsystem
■ Support for RAID 0, 1, 0+1, 1+0, and 5 storage configurations
■ Error correction and parity checking for improved data integrity
■ Easy access to all internal replaceable components
■ Easily accessible LED status indicators
■ Four different levels of system diagnostics

Chapter 1 System Overview 15

 Hot-Pluggable Disk Drives and PCI Cards
Sun Fire V890 system hardware is designed to support “hot-plugging” of internal
disk drives and PCI cards. With the proper software support, a qualified service
technician can install or remove these components while the system is running.
Hot-plug technology significantly increases the system’s serviceability and
availability, by providing the ability to:
■ Increase storage, and I/O capacity dynamically to handle larger work loads and
improve system performance
■ Replace disk drives and PCI cards without service disruption

A qualified service technician can hot-plug any standard PCI card, provided a
suitable software driver exists for the Solaris OS, and the driver supports PCI hot-
plug operations. In addition, the card must comply with the PCI Hot-Plug
Specification Revision 1.1, and the system must be running the Solaris 8 2/04
Operating System or a subsequent release that supports Sun Fire V890 PCI hot-plug
operations.

PCI hot-plug procedures may involve software commands for preparing the system
prior to removing a card and for reconfiguring the operating system after installing
a PCI card. For more information about PCI hot-plug procedures, see “About Hot-
Pluggable and Hot-Swappable Components” on page 127.

Caution – Do not attempt to hot-plug a PCI card until you are certain that its device
drivers support PCI hot-plug operations; otherwise, you may cause a system panic.
For a list of Sun PCI cards and device drivers that support PCI hot-plug operations,
see the Sun Fire V890 Server Product Notes.

For additional information about the system’s hot-pluggable components, see

“About Hot-Pluggable and Hot-Swappable Components” on page 127.

N+1 Power Supply Redundancy

The system includes three power supplies, two of which must be operational for the
system to function. The third supply provides N+1 redundancy, allowing the system
to continue operating should one of the power supplies fail.

For more information about power supplies, redundancy, and configuration rules,
see “About Power Supplies” on page 61.

16 Sun Fire V890 Server Owner’s Guide • October 2005

Hot-Swappable Power Supplies
Power supplies in a redundant configuration feature a “hot-swap” capability. You
can remove and replace a faulty power supply without shutting down the operating
system. The power supplies are easily accessed from the rear of the system, without
the need to remove system covers.

Redundant, Hot-Swappable Fan Trays

The basic system configuration includes two sets of three fan tray assemblies to
provide system cooling. One set of three fan tray assemblies provides primary
cooling, and the other set ensures redundancy that protects against cooling failures.
Only the primary fan trays are active during normal system operation. If a primary
fan tray fails, the environmental monitoring subsystem detects the failure and
automatically activates the appropriate secondary fan tray.

All fan trays feature a hot-swap capability. Qualified service technicians can remove
and replace a faulty fan tray without shutting down the operating system. For
additional details, see “About Fan Trays” on page 64.

Environmental Monitoring and Control

The Sun Fire V890 system features an environmental monitoring subsystem
designed to protect against:
■ Extreme temperatures
■ Lack of adequate airflow through the system
■ Power supply problems

Monitoring and control capabilities reside at the operating system level as well as in
the system’s flash PROM firmware. This ensures that monitoring capabilities remain
operational even if the system has halted or is unable to boot.

The environmental monitoring subsystem uses an industry standard I2C bus. The I2C
bus is a simple two-wire serial bus, used throughout the system to allow the
monitoring and control of temperature sensors, fans, power supplies, status LEDs,
and the front panel keyswitch.

Chapter 1 System Overview 17

 Thermal Monitoring
Temperature sensors are located throughout the system to monitor the ambient
temperature of the system and the temperature of each processor. The monitoring
subsystem frequently polls each sensor and uses the sampled temperatures to report
and to respond to any overtemperature or undertemperature conditions.

The hardware and software together ensure that the temperatures within the
enclosure do not stray outside predetermined “safe operation” ranges. If the
temperature observed by a sensor falls below a low-temperature warning threshold
or rises above a high-temperature warning threshold, the monitoring subsystem
software generates a WARNING message to the system console. If the temperature
exceeds a low- or high-temperature critical threshold, the software will issue a
CRITICAL message and proceed to gracefully shut down the system. In both cases,
the System Fault and Thermal Fault LEDs on the front status panel are illuminated
to indicate the nature of the problem.

This thermal shutdown capability is also built into the hardware circuitry as a
fail-safe measure. This feature provides backup thermal protection in the unlikely
event that the environmental monitoring subsystem becomes disabled at both the
software and firmware levels.

All error and warning messages are displayed on the system console (if one is
attached) and are logged in the /var/adm/messages file. Front panel fault LEDs
remain lit after an automatic system shutdown to aid in problem diagnosis.

Fan Monitoring
The monitoring subsystem is also designed to detect fan failures. The system
features three primary fan trays, which include a total of five individual fans, plus
three additional (secondary) fan trays for a total of 10 individual fans. During
normal operation, only the five primary fans are active. If any fan fails, the
monitoring subsystem detects the failure and:
■ Generates an error message and logs it in the /var/adm/messages file
■ Lights the System Fault and Thermal Fault LEDs on the status and control panel
■ Lights the appropriate fan fault LED inside the system
■ Automatically activates the appropriate secondary fan tray

Power Subsystem Monitoring

The power subsystem is monitored in a similar fashion. The monitoring subsystem
periodically polls the power supply status registers for a power supply OK status,
indicating the status of each supply’s 3.3V, 5.0V, 12V, and 48V DC outputs.

18 Sun Fire V890 Server Owner’s Guide • October 2005

If a power supply problem is detected, an error message is displayed on the system
console and logged in the /var/adm/messages file. The System Fault and Power
Fault LEDs on the status and control panel are also lit. LEDs located on the back of
each power supply will indicate the source and nature of the fault.

For more information about error messages generated by the environmental

monitoring subsystem, see Sun Fire V890 Diagnostics and Troubleshooting. You can
find this document at: http://www.sun.com/documentation. For more
information about system LEDs, see Chapter 8.

Automatic System Recovery

The Sun Fire V890 system provides a feature called automatic system recovery (ASR).
The ASR feature isolates failures and provides for the automatic restoration of the
operating system after certain non-fatal hardware faults or failures cause an
interruption. ASR does not prevent the operating system from going down in the
event of a hardware problem.

For more information, see “About Automatic System Recovery” on page 109.

Note – To enhance system restoration and server availability, Sun has recently
introduced a new standard (default) OpenBoot firmware configuration. These
changes, which affect the behavior of servers like the Sun Fire V890, are described in
OpenBoot PROM Enhancements for Diagnostic Operation. This document is included on
the Sun Fire V890 Documentation CD.

Hardware Watchdog Mechanism

To detect and respond to system hang conditions, the Sun Fire V890 system features
a hardware watchdog mechanism—a hardware timer that is continually reset as long
as the operating system is running. In the event of a system hang, the operating
system is no longer able to reset the timer. The timer will then expire and cause an
automatic system reset, eliminating the need for operator intervention.

Note – The hardware watchdog mechanism is not activated until you enable it.

To enable this feature, you must edit the /etc/system file to include the
following entry:

set watchdog_enable = 1

Chapter 1 System Overview 19

 This change does not take effect until you reboot the system.

Remote System Control Software

Remote System Control (RSC) software is a secure server management tool that lets
you monitor and control your server over a serial port or a network connection. RSC
provides remote system administration for geographically distributed or physically
inaccessible systems. The RSC software works with the system controller card on the
Sun Fire V890 system I/O board. The system controller card provides a private
Ethernet connection to a remote console, and a serial connection to a local
alphanumeric terminal.

Once RSC is configured to manage your server, you can use it to run diagnostic tests,
view diagnostic and error messages, reboot your server, and display environmental
status information from a remote console.

RSC provides the following features:

■ Remote system monitoring and error reporting (including diagnostic output)
■ Remote reboot, power-on, and power-off functions
■ Ability to monitor system environmental conditions remotely
■ Ability to run diagnostic tests from a remote console
■ Remote event notification for overtemperature conditions, power supply failures,
fatal system errors, or system crashes
■ Remote access to detailed event logs
■ Remote console functions via Ethernet or serial port

For additional details, see “About the System Controller Card and RSC Software” on
page 59 and “About Sun Remote System Control Software” on page 133.

Dual-Loop Enabled FC-AL Mass Storage

Subsystem
The system’s dual-ported FC-AL disk drives and dual-loop enabled backplanes can
be combined with an optional PCI FC-AL host adapter card to provide for fault
tolerance and high availability of data. This dual-loop configuration enables each
disk drive to be accessed through two separate and distinct data paths, providing:
■ Increased bandwidth – Allowing data transfer rates up to 200 Mbytes per second
versus 100 Mbytes per second for single-loop configurations
■ Hardware redundancy – Providing the ability to sustain component failures in one
path by switching all data transfers to an alternate path

20 Sun Fire V890 Server Owner’s Guide • October 2005

The mass storage subsystem is described in greater detail in Chapter 4. The split
backplane configuration is described in “Full vs. Split Backplane Configurations” on
page 83, and in the “Split Backplane Configurations” appendix in the Sun Fire V890
Server Service Manual.

Support for RAID Storage Configurations

Using a software RAID application such as Solstice DiskSuite™, you can configure
system disk storage in a variety of different RAID levels. Configuration options
include RAID 0 (striping), RAID 1 (mirroring), RAID 0+1 (striping plus mirroring),
RAID 1+0 (mirroring plus striping), and RAID 5 (striping with interleaved parity)
configurations. You choose the appropriate RAID configuration based on the price,
performance, and reliability and availability goals for your system. You can also
configure one or more drives to serve as “hot spares” to fill in automatically for a
defective drive in the event of a disk failure.

For more information, see “About Volume Management Software” on page 134.

Error Correction and Parity Checking

Error-correcting code (ECC) is used on all internal system data paths to ensure high
levels of data integrity. All data that moves between processors, memory, and PCI
bridge chips have end-to-end ECC protection.

The system reports and logs correctable ECC errors. A correctable ECC error is any
single-bit error in a 128-bit field. Such errors are corrected as soon as they are
detected. The ECC implementation can also detect double-bit errors in the same
128-bit field and multiple-bit errors in the same nibble (4 bits).

In addition to providing ECC protection for data, the system offers parity protection
on all system address buses. Parity protection is also used on the PCI bus, and in the
UltraSPARC processors’ internal and external cache.

Status LEDs
The system provides easily accessible light-emitting diode (LED) indicators to
provide a visual indication of system and component status. LEDs are located on the
system front panel, internal disk bays, power supplies, fan tray assemblies, and near
each CPU/Memory board and PCI slot. Status LEDs eliminate guesswork and
simplify problem diagnosis for enhanced serviceability.

Chapter 1 System Overview 21

 Front panel status LEDs are described in “About the Status and Control Panel” on
page 11. For details on the system internal LEDs, see Chapter 8.

Four Levels of Diagnostics

For enhanced serviceability and availability, the system provides four different levels
of diagnostic testing:
■ Power-on self-test (POST)
■ OpenBoot Diagnostics
■ Sun Validation Test Suite (SunVTS™)
■ Sun Management Center system monitoring and management software

POST and OpenBoot Diagnostics are firmware-resident diagnostics that can run
even if the server is unable to boot the operating system. POST diagnostics check the
functions of the core system hardware. OpenBoot Diagnostics focus on testing I/O
subsystems and plug-in cards.

Note – To enhance system restoration and server availability, Sun has recently
introduced a new standard (default) OpenBoot firmware configuration. These
changes, which affect the behavior of servers like the Sun Fire V890, are described in
OpenBoot PROM Enhancements for Diagnostic Operation. This document is included on
the Sun Fire V890 Documentation CD.

Application-level diagnostics, such as SunVTS and Sun Management Center

software, offer additional troubleshooting capabilities once the operating system is
running. SunVTS software provides a comprehensive test of the system, including its
external interfaces. SunVTS software also lets you run tests remotely over a network
connection or from an RSC console. Sun Management Center software provides a
variety of continuous system monitoring capabilities. It enables you to monitor
system hardware status and operating system performance of your server. For more
information about diagnostic tools, see Sun Fire V890 Diagnostics and Troubleshooting.
You can find this document at: http://www.sun.com/documentation.

22 Sun Fire V890 Server Owner’s Guide • October 2005

CHAPTER 2

Setting Up the System

This chapter describes what you need to do to get the Sun Fire V890 server up and
running. Where software is involved, this chapter explains some of what you need
to do, and points you to the appropriate software manuals for the rest.

Tasks covered in this chapter include:

■ “How to Install the Sun Fire V890 Server” on page 24
■ “How to Attach an Alphanumeric Terminal” on page 31
■ “How to Configure a Local Graphics Console” on page 33
■ “How to Power On the System” on page 35
■ “How to Power Off the System” on page 38
■ “How to Initiate a Reconfiguration Boot” on page 40
■ “How to Redirect the System Console to RSC” on page 42
■ “How to Restore the Local System Console” on page 45

Other information covered in this chapter includes:

■ “About the Parts Shipped to You” on page 23
■ “About Setting Up a Console” on page 30

About the Parts Shipped to You

Standard features for the Sun Fire V890 server are installed at the factory. However,
if you ordered options such as a monitor, these will be shipped to you separately.

Also, you should have received the Solaris Media Kit and documentation for all
appropriate system software. Check that you have received everything you ordered.

Inspect the shipping carton for evidence of physical damage. If a shipping carton is
damaged, request that the carrier's agent be present when the carton is opened. Keep
all contents and packing material for the agent’s inspection. Unpacking instructions
are printed on the outside of the shipping carton.

23
 How to Install the Sun Fire V890 Server
Each step in this procedure refers you to a particular document or to a section of this
guide for instructions. Complete each step in the order listed.

Before You Begin

The Sun Fire V890 server is a general-purpose server, which you can use for many
types of applications. Exactly how you set up your machine depends on what you
want it to do.

This procedure is intended to be as “generic” as possible, so as to cover the needs of

most sites. Even so, you will need to make certain decisions to complete the
procedure:
■ On which network or networks do you intend your machine to operate?
For background information about network support, see “About Network
Interfaces” on page 90.
■ How do you want to configure and use your system’s internal storage array?
For background information about internal storage array configuration options, see
“Mass Storage Subsystem Configuration” on page 77.
■ What software do you intend to load?

Software included in the Solaris Media Kit or other software products may impose
certain disk space or disk partitioning requirements. Refer to the documentation
accompanying the software to determine those requirements.

Note – Refer to the Sun Fire V890 Server Product Notes for information about the
software applications and Solaris OS for your system, before you install your Sun
Fire V890 server.

What to Do
1. Verify that you have received all the parts of your system.
See “About the Parts Shipped to You” on page 23.

24 Sun Fire V890 Server Owner’s Guide • October 2005

2. Set up the system in an appropriate environment.
The Sun Fire V890 server can be installed as a deskside or a rackmounted system. If
you are installing the system in a rack, follow the instructions in the Sun Fire V890
Server Rackmounting Guide, which is available at
http://www.sun.com/documentation.

Note – Do not install optional equipment into a system that you are rackmounting
until after you have installed the system into the rack.

If you are installing your server as a deskside system and need information about
positioning the system in an appropriate environment, see the Site Planning Guide for
Entry-Level Servers, which is included on the Sun Fire V890 Documentation CD.

3. Connect an AC power cord to each AC inlet at the back of each power supply.
Connect the opposite end of each power cord to a grounded, dedicated AC power
outlet.
Use the power cord supplied with the V890 server. The V890 server uses 200-240
VAC line input only.

Note – You must connect each power supply to a dedicated AC circuit. Consult
your local electrical codes for any additional requirements.

4. Attach a strain relief to each AC power cord.

The strain relief is a plastic tie-wrap and pedestal that is inserted into the rear panel
of the server. Use these reliefs to manage the power cords after you have installed
the cords into the AC inlets in the server.
To use a strain relief, press the tab to release the tie-wrap. Wrap the loose end of the
tie-wrap around the AC power cord and thread the tie-wrap through the opening in
the relief pedestal. Pull up the end of the tie-wrap to tighten it.

Chapter 2 Setting Up the System 25

 5. Install any optional components shipped with your system.
If you ordered options that are not factory-installed, see the Sun Fire V890 Server
Service Manual for installation instructions.

Note – Do not install optional PCI cards into the system until after you have
powered on and tested the system.

Caution – The AC power cords provide a discharge path for static electricity, so
they must remain plugged in to AC power outlets when installing or handling any
internal component, except for the system controller card. Prior to servicing the system
controller card, make sure that all AC power cords are disconnected.

Caution – All internal options (except disk drives and power supplies) must be
installed only by qualified service personnel. Installation procedures for these
components are covered in the Sun Fire V890 Server Service Manual, which is
included on the Sun Fire V890 Documentation CD.

26 Sun Fire V890 Server Owner’s Guide • October 2005

6. If necessary, configure the serial port jumpers and connect any serial peripheral
devices.
Two serial port jumpers located on the system I/O board are used to configure the
system’s serial ports to operate in compliance with the Electronics Industries
Association EIA-423 or EIA-232D standards. The jumpers are factory-set for the
EIA-423 standard, which is the default standard for North American users.
Compliance with the EIA-232D standard is required for digital telecommunication
in nations of the European Community. If you require EIA-232D compliance, see
the Sun Fire V890 Server Service Manual and “About Serial Port Jumpers” on
page 70. For information about serial port characteristics, see “About the Serial
Ports” on page 67.

Caution – All internal jumper modifications must be performed only by qualified

service personnel.

7. Set up a system console.

You must set up a terminal or console in order to install system software and to view
diagnostic messages.
At initial installation, you can either establish a tip connection from another server
or attach an alphanumeric (ASCII) terminal to the serial port. See “About Setting Up
a Console” on page 30.

Note – By default, power-on self-test (POST) messages are output to serial port A
(ttya). After initial installation you can configure the system to use RSC as the
system console and the system will redirect POST output to the RSC console. To
perform initial installation, you need a console connected to serial port A to view
POST diagnostic output.

Note – You cannot use RSC to perform the initial installation of the Solaris OS. You
must install the operating system prior to setting up an RSC console.

8. Prepare the network interface(s).

The Sun Fire V890 server provides two on-board Ethernet interfaces as part of the
standard configuration—one Fast Ethernet interface and one Gigabit Ethernet
interface. A variety of supported PCI cards can provide connections to additional
Ethernet or other network types. For details about network interface options and
configuration procedures, see the following sections:
■ “About Network Interfaces” on page 90
■ “How to Configure the Primary Network Interface” on page 92
■ “How to Configure Additional Network Interfaces” on page 94

Chapter 2 Setting Up the System 27

 9. Turn on power to your server.
See “How to Power On the System” on page 35.
When you power on the system for the first time, your system automatically runs
power-on self-test (POST) and OpenBoot Diagnostics tests and displays the output
on your console. The system also enables automatic system recovery (ASR).

Note – The system may take up to 30 minutes or longer to run diagnostic tests and
display status messages before the ok prompt appears on the system console. The
time depends on the system configuration (number of processors, memory modules,
and PCI cards) and the standard configuration of the OpenBoot variables, which by
default are set at diag-level=max and verbosity=normal. To estimate boot
time, and to customize the standard configuration after initial power-on, see the
OpenBoot PROM Enhancements for Diagnostic Operation guide, which is included on
the Sun Fire V890 Documentation CD.

10. Install and boot the Solaris Operating System.

See the installation instructions provided with your Solaris software. You should
also consult the Sun Fire V890 Server Product Notes for information about the Solaris
OS for your system.

11. Install and configure Remote System Control (RSC) software.

Install the Remote System Control (RSC) software, which is included in the Solaris
Media Kit. You must manually install the RSC software before you can use RSC.
For information about configuring and using RSC, see the Sun Remote System Control
(RSC) 2.2 User’s Guide, which is included on the Sun Fire V890 Documentation CD.

Note – Once you install RSC software, you can configure the system to use RSC as
the system console. For detailed instructions, see “How to Redirect the System
Console to RSC” on page 42.

12. (Optional) Load additional software from the Solaris Media Kit.
The Solaris Media Kit (sold separately) includes several CDs containing software to
help you operate, configure, and administer your server. See the documentation
provided with the Solaris Media Kit for a complete listing of included software and
detailed installation instructions.

13. Check and update the FC-AL disk backplane firmware.

Installing the latest version of FC-AL backplane firmware ensures that the I/O
system runs properly. Refer to the Sun Fire V890 Server Product Notes for information
about checking and loading the latest backplane firmware.

28 Sun Fire V890 Server Owner’s Guide • October 2005

14. Load any required and recommended patches for the system, if necessary.
Your system may be preinstalled with all required patches. Refer to the Sun Fire
V890 Server Product Notes for information about patches. Check the SunSolve
OnlineSM web site for any recent patches and service information about the system at
http://sunsolve.sun.com.

15. Set any desired OpenBoot PROM configuration options.

You can control several aspects of system behavior through OpenBoot PROM
commands and configuration variables. For additional details, see “Configuring
System Firmware” on page 103.

16. Configure any additional network interfaces.

The Sun Fire V890 server provides two on-board Ethernet interfaces. Additional
interfaces and connections are available by installing the appropriate PCI interface
cards. See the Sun Fire V890 Server Service Manual, which is included on the Sun Fire
V890 Documentation CD for installation instructions.

17. Load the electronic documentation from the Sun Fire V890 Documentation CD.
Directions for loading the documentation are printed in the booklet that
accompanies the CD.

18. Turn the system keyswitch to the Locked position.

The Locked position is the recommended setting for day-to-day operations. This
setting disables the system Power button, disables certain types of break commands
that allow access to the ok prompt, and prevents unauthorized programming of the
system’s flash PROMs.

Chapter 2 Setting Up the System 29

 About Setting Up a Console
To install your server or to diagnose problems, you need some way to enter system
commands and to view system output. There are four ways to do this.

1. Attach an alphanumeric (ASCII) character terminal to serial port A.

You can attach a simple terminal to serial port A. For instructions, see “How to
Attach an Alphanumeric Terminal” on page 31.

2. Establish a tip connection from another Sun system.

For general information about establishing a tip connection, see the OpenBoot
4.x Command Reference Manual, which is available at http://docs.sun.com,
under Solaris on Sun Hardware. Refer to the Sun Fire V890 Server Product Notes
for late-breaking details.

3. Install a local graphics console on your server.

The server is often shipped without a mouse, keyboard, monitor, or frame buffer for
the display of graphics. To install a local graphics console on a server, a qualified
service technician must install a graphics frame buffer card in a PCI slot, and attach
a monitor, mouse, and keyboard to the appropriate rear panel ports. For detailed
instructions, see “How to Configure a Local Graphics Console” on page 33.

Note – Power-on self-test (POST) messages are output to serial port A (ttya) or the
RSC console only.

4. Set up a Remote System Control (RSC) console.

RSC is a secure server management tool that lets you monitor and control your
server over a serial port or a network connection. RSC provides convenient remote
system administration for geographically distributed or physically inaccessible
systems. For additional details, see “About the System Controller Card and RSC
Software” on page 59 and “About Sun Remote System Control Software” on
page 133.

Note – You cannot use an RSC console to perform the initial installation of the
Solaris OS. The operating system must be installed prior to setting up an RSC
console. Once you install the operating system and the RSC software, you can
configure the system to use RSC as the system console. For detailed instructions, see
“How to Redirect the System Console to RSC” on page 42.

30 Sun Fire V890 Server Owner’s Guide • October 2005

 How to Attach an Alphanumeric
Terminal

Before You Begin

If your server is configured without a local graphics console, you need to attach an
alphanumeric (ASCII) terminal to the server in order to install the Solaris Operating
System and to run diagnostic tests. Alternatively, you can install a local graphics
console, create a tip connection from another Sun system, or set up an RSC console.
For more information, see “About Setting Up a Console” on page 30.

Note – You cannot use an RSC console to perform the initial installation of the
Solaris OS. The Solaris OS must be installed prior to setting up an RSC console.

What to Do
1. Connect a DB-25 null modem serial cable or a DB-25 serial cable and null modem
adapter to the terminal’s serial port.

2. Connect the opposite end of the cable to the system’s serial port connector or to
serial port A on the serial splitter cable.

Chapter 2 Setting Up the System 31

 3. Connect the terminal’s power cable to an AC outlet.

4. Set the terminal to receive:

■ At 9600 baud
■ An 8-bit signal with no parity and 1 stop bit

See the documentation accompanying your terminal for more information.

What Next
You can now issue system commands and view system messages. Continue with
your installation or diagnostic procedure as needed.

32 Sun Fire V890 Server Owner’s Guide • October 2005

 How to Configure a Local Graphics
Console

Before You Begin

If your server is configured without a local alphanumeric (ASCII) terminal, you need
to install a local graphics console in order to install the Solaris Operating System and
to run diagnostic tests. Alternatively, you can attach an alphanumeric terminal,
create a tip connection from another Sun system, or set up an RSC console. For
more information, see “About Setting Up a Console” on page 30.

Note – You cannot use an RSC console to perform the initial installation of the
Solaris OS. The Solaris OS must be installed prior to setting up an RSC console.

To install a local graphics console, you must have:

■ A supported PCI-based graphics frame buffer card and software driver
■ A monitor with appropriate resolution
■ A Sun Type-6 USB keyboard
■ A Sun-compatible USB three-button mouse

What to Do
1. Install the graphics card into an appropriate PCI slot.
For information about PCI buses and slots, see “About PCI Cards and Buses” on
page 56.

Note – PCI cards must be installed only by qualified service personnel. Installation
procedures for PCI cards are covered in the Sun Fire V890 Server Service Manual,
which is included on the Sun Fire V890 Documentation CD.

Chapter 2 Setting Up the System 33

 2. Attach the monitor’s video cable to the graphic card’s video port.
Tighten the thumbscrews to secure the connection.

3. Connect the monitor’s power cord to an appropriate AC power outlet.

4. Attach the keyboard cable to one of the system’s USB ports.

34 Sun Fire V890 Server Owner’s Guide • October 2005

5. Attach the mouse cable to the system’s remaining USB port, or to a USB port on
the keyboard, if applicable.

What Next
You can now issue system commands and view system messages. Continue with
your installation or diagnostic procedure as needed.

How to Power On the System

Before You Begin

Do not use this power-on procedure if the operating system is already installed and
you have just added a new internal option or external storage device. To power on
the system after adding one of these options, see:
■ “How to Initiate a Reconfiguration Boot” on page 40

What to Do

Caution – Before you power on the system, make sure that the front and side doors
and all plastic outer panels are properly installed.

1. Turn on power to any peripherals and external storage devices.

2. Turn on power to the alphanumeric terminal or local graphics console, if present.

Chapter 2 Setting Up the System 35

 3. Insert the system key into the front panel keyswitch and turn it to the Normal or
Diagnostics position.
Normal position will enable the standard OpenBoot configuration for diagnostic
testing as defined for your system.
Diagnostics position will enable service mode and a Sun prescribed level of
diagnostic execution. Your system will automatically run maximum POST and
OpenBoot Diagnostics tests and display the output.
For information about the standard default Open Boot configuration for diagnostic
testing, see the OpenBoot PROM Enhancements for Diagnostic Operations Guide, which
is included on the Sun Fire V890 Documentation CD.
See “About the Status and Control Panel” on page 11 for more keyswitch
information.

Normal
position

Diagnostics
position

Note – The system will require a manual boot to the operating environment when
the keyswitch is in the Diagnostics position.

Note – For high availability environments, place the keyswitch in the Locked or
Normal postion.

36 Sun Fire V890 Server Owner’s Guide • October 2005

4. Press the Power button to the left of the keyswitch to power on the system.

Note – The system may take up to 30 minutes or longer to run diagnostic tests and
display status messages before the ok prompt appears on the system console. The
time depends on the system configuration (number of processors, memory modules,
and PCI cards) and the configuration of the OpenBoot variables, which by default
are set at diag-level=max and verbosity=normal. To estimate boot time, and
to customize the standard configuration after initial power on, see the OpenBoot
PROM Enhancements for Diagnostic Operation guide, which is included on the Sun
Fire V890 Documentation CD.

5. Turn the keyswitch to the Locked position.

This prevents anyone from accidentally powering off the system.

Locked
position

6. Remove the key from the keyswitch and keep it in a secure place.

What Next
The system’s front panel LED indicators provide power-on status information.
For more information about the system LEDs, see “About the Status and Control
Panel” on page 11.

Chapter 2 Setting Up the System 37

 How to Power Off the System

What to Do
1. Notify users that the system will be powered down.

2. Back up the system files and data, if necessary.

3. Ensure that the front panel keyswitch is in the Normal or Diagnostics position.

Normal
position

Diagnostics
position

4. Press and release the Power button on the system front panel.
The system begins a graceful software system shutdown.

Note – Pressing and releasing the Power button initiates a graceful software system
shutdown. Pressing and holding in the Power button for five seconds causes an
immediate hardware shutdown. Whenever possible, you should use the graceful
shutdown method. Forcing an immediate hardware shutdown may cause disk drive
corruption and loss of data. Use this method only as a last resort.

5. Wait for the front panel Power/OK LED to turn off.

6. Turn the keyswitch fully counterclockwise to the Forced Off position.

38 Sun Fire V890 Server Owner’s Guide • October 2005

 Forced Off position

Caution – Be sure to turn the keyswitch to the Forced Off position before handling
any internal components. Otherwise, it is possible for an RSC user to restart the
system remotely while you are working inside it. The Forced Off position is the only
keyswitch position that prevents an RSC user from restarting the system.

7. Remove the key from the keyswitch and keep it in a secure place.

Chapter 2 Setting Up the System 39

 How to Initiate a Reconfiguration Boot
After installing any new internal option or external storage device, you must
perform a reconfiguration boot so that the operating system is able to recognize the
newly installed device(s). In addition, if a qualified service technician removes a
device and does not install a replacement device prior to rebooting the system, you
must perform a reconfiguration boot in order for the operating system to recognize
the configuration change. This requirement also applies to any component that is
connected to the system’s I2C bus, including memory modules, CPU/Memory
boards, and power supplies.

This requirement does not apply to any component that is:

■ Installed or removed as part of a hot-plug operation
■ Installed or removed before the operating system is installed
■ Installed as an identical replacement for a component that is already recognized
by the operating system, excluding FCAL disk drives

Caution – All internal options (except disk drives and power supplies) must be
installed only by qualified service personnel. Installation procedures for these
components are covered in the Sun Fire V890 Server Service Manual, which is
included on the Sun Fire V890 Documentation CD.

Before You Begin

Caution – Before you power on the system, make sure that the front and side doors
and all plastic outer panels are properly installed.

You need a system console in order to issue software commands; see:

■ “About Setting Up a Console” on page 30

What to Do
1. Turn on power to any peripherals and external storage devices.
Read the documentation supplied with the device for specific instructions.

2. Turn on power to the console.

40 Sun Fire V890 Server Owner’s Guide • October 2005

3. Insert the system key into the front panel keyswitch and turn the keyswitch to the
Normal position.

4. Press the Power button to the left of the keyswitch to power on the system.

Normal
position

5. When the diagnostic tests are completed, the system banner is displayed on the
system console followed by the ok prompt.
The system banner contains the Ethernet address and host ID.

Note – The system may take up to 30 minutes or longer to run diagnostic tests and
display status messages before the ok prompt appears on the system console. The
time depends on the system configuration (number of processors, memory modules,
and PCI cards) and the standard default configuration of the OpenBoot variables,
which by default are set at diag-level=max and verbosity=normal. To
customize the standard configuration after initial power on, see the OpenBoot PROM
Enhancements for Diagnostic Operation guide, which is included on the Sun Fire V890
Documentation CD.

6. At the ok prompt, type:

ok env-on
Environmental monitor is ON
ok boot -r

The env-on command re-enables the OpenBoot environmental monitor, which may
have been disabled as a result of the abort key sequence. The boot -r command
rebuilds the device tree for the system, incorporating any newly installed options so
that the operating system will recognize them.

Chapter 2 Setting Up the System 41

 7. Turn the keyswitch to the Locked position, remove the key, and keep it in a secure
place.
This prevents anyone from accidentally powering off the system.

Locked
position

What Next
The system’s front panel LED indicators provide power-on status information.
For more information about the system LEDs, see “About the Status and Control
Panel” on page 11.

If your system encounters a problem during system start-up, and the keyswitch is in
the Normal position, try restarting the system with the keyswitch in the Diagnostics
position to determine the source of the problem. Turn the front panel keyswitch to
the Diagnostics position and power cycle the system.

How to Redirect the System Console

to RSC
Perform this procedure if, after installing the Solaris Operating System and the RSC
software, you want to configure the system to use RSC as the system console. For
more information about RSC, see “About the System Controller Card and RSC
Software” on page 59 and “About Sun Remote System Control Software” on
page 133.

42 Sun Fire V890 Server Owner’s Guide • October 2005

 Note – When you configure the system to use RSC as the system console, power-on
self-test (POST) diagnostic output is redirected to the RSC console.

Before You Begin

This procedure assumes that you are familiar with the OpenBoot firmware and that
you know how to enter the OpenBoot environment. For more information about the
OpenBoot firmware, see the OpenBoot 4.x Command Reference Manual, which is
available at http://docs.sun.com, under Solaris on Sun Hardware. Refer also to
the Sun Fire V890 Server Product Notes for late-breaking information.

What to Do
1. Type the following commands at the system ok prompt:

ok diag-console rsc
ok setenv input-device rsc-console
ok setenv output-device rsc-console

The system permanently stores the new settings. The changes will take effect after
the next reset.

2. To cause the changes to take effect immediately, reset the system, type:

ok reset-all

The system permanently stores the changes and boots automatically if the OpenBoot
variable auto-boot? is set to true (its default value).

A power cycle will also cause the changes to take effect immediately.

Chapter 2 Setting Up the System 43

 Note – In the unlikely event that the system controller card fails while the system
console is directed to RSC, the system console will be unavailable. To recover from
this situation, press the system Power button to initiate a graceful software
shutdown. Then turn the keyswitch to the Diagnostics position or use the OpenBoot
emergency procedure for resetting ID PROM configuration variables to their default
values. See “About OpenBoot Emergency Procedures” on page 119. These measures
will temporarily redirect the system console to the factory default device. If you are
not installing a replacement system controller card right away, you may want to
restore the local system console until a replacement card is available. See “How to
Restore the Local System Console” on page 45.

Caution – All internal options (except disk drives and power supplies) must be
installed only by qualified service personnel. Installation procedures for these
components are covered in the Sun Fire V890 Server Service Manual, which is
included on the Sun Fire V890 Documentation CD.

What Next
For instructions on how to use the system controller card and RSC software, see the
Sun Remote System Control (RSC) User’s Guide, which is included on the Sun Fire
V890 Documentation CD.

44 Sun Fire V890 Server Owner’s Guide • October 2005

 How to Restore the Local System
Console
Perform this procedure if your system is configured to use RSC as the system
console and you need to redirect the system console to a local graphics console,
alphanumeric terminal, or an established tip connection. For more information
about RSC, see “About the System Controller Card and RSC Software” on page 59
and “About Sun Remote System Control Software” on page 133.

Before You Begin

This procedure assumes that you are familiar with the OpenBoot firmware and that
you know how to enter the OpenBoot environment. For more information about the
OpenBoot firmware, see the OpenBoot 4.x Command Reference Manual, which is
available at http://docs.sun.com, under Solaris on Sun Hardware. Refer also to
the Sun Fire V890 Server Product Notes for late-breaking information.

What to Do
1. Type the following commands at the system ok prompt:

ok diag-console ttya
ok setenv input-device keyboard
ok setenv output-device screen

The system permanently stores the new settings. The changes will take effect after
the next reset.

2. To cause the changes to take effect immediately, type:

ok reset-all

The system permanently stores the parameter changes and boots automatically if the
OpenBoot variable auto-boot? is set to true (its default value).

Note – A power-cycle will also cause the changes to take effect immediately.

Chapter 2 Setting Up the System 45

46 Sun Fire V890 Server Owner’s Guide • October 2005
CHAPTER 3

Hardware Configuration

This chapter provides hardware configuration information for the Sun Fire V890
server. The following topics are covered in this chapter:
■ “About CPU/Memory Boards” on page 48
■ “About Memory Modules” on page 51
■ “About PCI Cards and Buses” on page 56
■ “About the System Controller Card and RSC Software” on page 59
■ “About Power Supplies” on page 61
■ “About Fan Trays” on page 64
■ “About Removable Media Devices” on page 67
■ “About the Serial Ports” on page 67
■ “About the USB Ports” on page 68
■ “About Hardware Jumpers” on page 69
■ “About Serial Port Jumpers” on page 70
■ “About Flash PROM Jumpers” on page 72

Note – For configuration information about the internal mass storage subsystem,
see “Mass Storage Subsystem Configuration” on page 77. For configuration
information about network interfaces, see “Configuring Network Interfaces” on
page 89.

47
 About CPU/Memory Boards
The system motherboard provides slots for up to four CPU/Memory boards. Each
CPU/Memory board incorporates two UltraSPARC chip multithreading (CMP)
processors, with 16 Mbytes of static random access memory (SRAM) Level 2 external
cache memory per processor, and slots for 16 memory modules. The external cache
memory cannot be upgraded.

Note – You must use CPU/Memory boards of the same speed within a Sun Fire
V890 system.

Chip multithreading technology allows two threads per UltraSPARC processor. With
this dual-threaded architecture, each UltraSPARC processor consists of two virtual
processors with shared memory. A dynamic arbitration scheme enables each thread
to make optimal use of the available memory, resulting in higher performance.

48 Sun Fire V890 Server Owner’s Guide • October 2005

The following illustration shows the four CPU/Memory board slots on the system
motherboard. The slots are labeled A through D from bottom to top. The virtual
processors (CPUs) in the system have unique numbers, depending on the slot where
each CPU/Memory board resides. For example, a CPU/Memory board installed in
slot D always contains CPUs 5 and 21 and 7 and 23, even if there are no other
CPU/Memory boards installed in the system.

7,23
5,21

Slot D

6,22
4,20

Slot C

3,19
1,17

Slot B

2,18

0,16

Slot A

Chapter 3 Hardware Configuration 49

 The UltraSPARC processor is a high-performance, highly integrated, CMP processor
that enables an increase in application throughput while maintaining binary
compatibility. It implements a 64-bit SPARC International Version 9 Instruction Set
Architecture (ISA).

The UltraSPARC processor improves throughput performance in commercial

applications such as databases, web servers, and high-performance technical
computing. It supports both 2D and 3D graphics, as well as image processing, video
compression and decompression, and video effects through the sophisticated Visual
Instruction Set (VIS) extension. VIS provides high levels of multimedia performance,
including real-time video compression and decompression and two streams of
MPEG-2 decompression at full broadcast quality with no additional hardware
support.

The Sun Fire V890 server employs a shared-memory multiprocessor architecture

with all processors sharing the same physical address space. The UltraSPARC
processors, main memory, and I/O subsystem communicate via a high-speed system
interconnect bus, operating at a clock rate of 150 MHz. In a system configured with
multiple CPU/Memory boards, all main memory is accessible from any processor
over the system bus. The main memory is shared logically by all processors and I/O
devices in the system.

For information about memory modules and memory configuration guidelines, see
“About Memory Modules” on page 51.

Caution – CPU/Memory boards must be installed only by a qualified service

technician. After installing a CPU/Memory board, you must perform a
reconfiguration boot in order for the environmental software to recognize the new
device. See “How to Initiate a Reconfiguration Boot” on page 40.

Caution – Either a CPU/Memory board or an air baffle must be installed in each

CPU/Memory slot at all times. After removing a CPU/Memory board, a
qualified service technician must install a replacement board or an air baffle
immediately to avoid an automatic thermal shutdown. For installation
instructions, see the Sun Fire V890 Server Service Manual, which is included on the
Sun Fire V890 Documentation CD.

50 Sun Fire V890 Server Owner’s Guide • October 2005

About Memory Modules
The Sun Fire V890 server uses 3.3-volt, high-capacity dual inline memory modules
(DIMMs). The DIMMs are built with synchronous dynamic random access memory
(SDRAM) chips that operate at a 75-MHz clock frequency. The system supports
DIMMs of various capacities. For details, see the Sun Fire V490/V890 CPU/Memory
Module Configuration Guide, available from:
http://www.sun.com/products-n-solutions/hardware/docs/Servers/

Each CPU/Memory board contains slots for 16 DIMMs. Total system memory
available depends on the capacity of the DIMMs installed.

Within each CPU/Memory board, the 16 DIMM slots are organized into groups of
four. The system reads from, or writes to, all four DIMMs in a group simultaneously.
DIMMs, therefore, must be added in sets of four.

The figure below shows the DIMM slots and DIMM groups on a Sun Fire V890
CPU/Memory board. Every fourth slot belongs to the same DIMM group. The four
groups are designated A0, A1, B0, and B1.

Chapter 3 Hardware Configuration 51

 A0 A1 B0 B1

A0 A1 B0 B1

A0 A1 B0 B1

A0 A1 B0 B1

Qualified service technicians must physically remove a CPU/Memory board from

the system before installing or removing DIMMs. The DIMMs must be added four at
a time within the same DIMM group and be identical—that is, all DIMMs must be
from the same manufacturing vendor and must have the same capacity (for example,
four 512-Mbyte DIMMs, or four 1-Gbyte DIMMs).

52 Sun Fire V890 Server Owner’s Guide • October 2005

Memory Interleaving
You can maximize the system’s memory bandwidth by taking advantage of its
memory interleaving capabilities. Sun Fire V890 systems support two-way, four-way,
and eight-way memory interleaving. In most cases, higher interleaving factors result
in greater system performance. However, actual performance results may vary
depending on the system application.

The system’s interleaving capabilities are summarized as follows:

■ Memory interleaving is limited to memory within the same CPU/Memory board.
Memory interleaving between CPU/Memory boards is not supported.
■ Eight-way interleaving occurs automatically when all 16 DIMM slots in a
CPU/Memory board are filled with identical capacity DIMMs (16 identical
DIMMs).
■ Four-way interleaving occurs automatically between any two DIMM groups that
are configured identically (eight identical capacity DIMMs).
■ Two-way interleaving occurs automatically in any DIMM group where the DIMM
capacities do not match the capacities used in any other group.

Independent Memory Subsystems

Each Sun Fire V890 CPU/Memory board contains two independent memory
subsystems (one per UltraSPARC processor). Memory controller logic incorporated
into the UltraSPARC processor enables each processor to control its own memory
subsystem. One processor controls DIMM groups A0 and A1, while the other
processor controls DIMM groups B0 and B1.

The Sun Fire V890 system uses a shared-memory architecture. During normal system
operations, the total system memory is shared by all processors in the system.
However, in the event of a processor failure, the two DIMM groups associated with
the failed processor become unavailable to all other processors in the system.

The following table shows the association between the processors and their
corresponding DIMM groups.

Processor
Number CPU/Memory Slot Associated DIMM Groups

0 Slot A A0, A1
2 Slot A B0, B1
1 Slot B A0, A1
3 Slot B B0, B1

Chapter 3 Hardware Configuration 53

 Processor
Number CPU/Memory Slot Associated DIMM Groups

4 Slot C A0, A1
6 Slot C B0, B1
5 Slot D A0, A1
7 Slot D B0, B1

Configuration Rules
■ DIMMs must be added four-at-a-time within the same group of DIMM slots;
every fourth slot belongs to the same DIMM group.
■ Each group used must have four identical DIMMs installed—that is, all four
DIMMs must be from the same manufacturing vendor and must have the same
capacity (for example, four 512-Mbyte or four 1-Gbyte DIMMs).
■ Each CPU/Memory board must be populated with a minimum of 8 identical
DIMMs

Caution – All internal options (except disk drives and power supplies) must be
installed only by qualified service personnel. For information about installing or
removing DIMMs, see the Sun Fire V890 Server Service Manual, which is included on
the Sun Fire V890 Documentation CD.

Caution – DIMMs are made of electronic components that are extremely sensitive
to static electricity. Static from your clothes or work environment can destroy the
modules. Do not remove a DIMM from its antistatic packaging until you are ready to
install it on the CPU/Memory board. Handle the modules only by their edges. Do
not touch the components or any metal parts. Always wear an antistatic grounding
strap when you handle the modules. For more information about avoiding
electrostatic discharge, see the Sun Fire V890 Server Service Manual, which is included
on the Sun Fire V890 Documentation CD.

54 Sun Fire V890 Server Owner’s Guide • October 2005

The following table summarizes the guidelines for installing DIMMs in a
CPU/Memory board. DIMMs must be installed by a qualified service technician.
Refer to the Sun Fire V890 Server Service Manual, which is included on the Sun Fire
V890 Documentation CD for installation instructions.

Population Sequence Memory Interleaving Factor

Install first eight Four-way interleaving if all eight

DIMMs into groups A0 DIMMs are identical; two-way
and B0 (so that every interleaving otherwise
other slot is occupied).

Install next four Four-way interleaving between

DIMMs into group A1. any two groups configured
identically; two-way interleaving
in any group that does not match
the capacities used in any other
group

Fill last four available Eight-way interleaving if all 16

slots (group B1). DIMMs are identical; four-way
interleaving between any two
groups configured identically;
two-way interleaving in any
group that does not match the
capacities used in any other
group

Chapter 3 Hardware Configuration 55

 About PCI Cards and Buses
All system communication with storage peripherals and network interface devices is
mediated by two Peripheral Component Interconnect (PCI) bridge chips, located on
the system’s motherboard. Each bridge chip manages communication between the
system’s main interconnect bus and two PCI buses, giving the system a total of four
separate PCI buses. The four PCI buses support up to nine PCI interface cards and
four motherboard devices.

The following table describes the PCI bus characteristics and maps each bus to its
associated bridge chip, motherboard devices, and PCI slots. All slots comply with
PCI Local Bus Specification Revision 2.1.

Clock Rate (MHz)/

Bandwidth (bits)/
PCI Bridge PCI Bus Voltage (V) Motherboard Devices PCI Slots

0 PCI A 66 MHz/ Gigabit Ethernet controller None. Used

64 bits/ FC-AL controller for integrated
3.3V controllers
only
0 PCI B 33 MHz/ IDE controller (interface to Slots 0, 1, 2, 3
64 bits/ the IDE DVD-ROM drive)
5V
1 PCI C 33 or 66 MHz/ None Slots 7 and 8
64 bits/
3.3V
1 PCI D 33 MHz/ System controller card, Slots 4, 5, 6
64 bits/ RIO ASIC (Ethernet, USB,
5V and EBus interfaces)

The system’s PCI hot-plug feature allows a qualified service technician to remove
and install PCI cards while the system is running. A qualified service technician can
hot-plug any standard PCI card, provided that its Solaris device drivers support PCI
hot-plug operations, and the system is running a Solaris Operating System that
supports Sun Fire V890 PCI hot-plug operations. In addition, the PCI card must
comply with the PCI Hot-Plug Specification Revision 1.1.

PCI hot-plug procedures may involve software commands for preparing the
system prior to removing a card and for reconfiguring the operating system
after installing a PCI card. For more information about PCI hot-plug
procedures, see “About Hot-Pluggable and Hot-Swappable Components” on
page 127.

56 Sun Fire V890 Server Owner’s Guide • October 2005

Caution – Do not attempt to hot-plug a PCI card until you are certain that its device
drivers support PCI hot-plug operations; otherwise, you may cause a system panic.
For a list of Sun PCI cards and device drivers that support PCI hot-plug operations,
see the Sun Fire V890 Server Product Notes.

Status LEDs provide power, fault, and hot-plug status indications for each PCI slot.
A contact push button is also provided for each slot, which allows the service
technician to initiate the hot-plug procedure at the server. For information about the
status indicator LEDs, see “About PCI Slot LEDs” on page 144.

The following figure shows the PCI slots on the I/O board.

Slot 8 – 33/66MHz, 3.3V

Slot 7 – 33/66MHz, 3.3V
Slot 6 – 33MHz, 5V
Slot 5 – 33MHz, 5V
Slot 4 – 33MHz, 5V
Slot 3 – 33MHz, 5V
Slot 2 – 33MHz, 5V
Slot 1 – 33MHz, 5V
Slot 0 – 33MHz, 5V

Chapter 3 Hardware Configuration 57

 Configuration Rules
■ All slots accept short or long PCI cards.
■ 5V PCI cards must be installed into 5V slots. 3.3V PCI cards must be installed into
3.3V slots. All slots accept universal (3.3V/5V) PCI cards.
■ All slots accept either 32-bit or 64-bit PCI cards.
■ All slots comply with PCI Local Bus Specification Revision 2.1.
■ Each slot can supply up to 25 watts of power. The total power used for all nine
slots must not exceed 135 watts.
■ Compact PCI (cPCI) cards and SBus cards are not supported.
■ Slots 7 and 8 can operate at either 33 or 66 MHz; however, both slots always
operate at the same speed. When the system is booted, if neither slot contains a
33-MHz PCI card, both slots operate at 66 MHz. If you then add a PCI card to
either slot via a hot-plug operation, the card must be a 66-MHz card; a 33-MHz
card will fail to operate under these conditions.
■ If either slot 7 or 8 contains a 33-MHz PCI card when the system is booted, both
slots operate at 33 MHz. In this case, either slot can accept a 33-MHz or 66-MHz
card via a hot-plug operation; however, 66-MHz cards will operate at 33 MHz.
■ For best performance, install high-throughput cards into slots 7 and 8.
■ You can improve overall system availability by installing redundant network or
storage interfaces on separate PCI buses and PCI bridges. For additional
information, see “About Multipathing Software” on page 131.

Caution – All internal options (except disk drives and power supplies) must be
installed only by qualified service personnel. For information about installing or
removing PCI cards, see the Sun Fire V890 Server Service Manual, which is included
on the Sun Fire V890 Documentation CD.

58 Sun Fire V890 Server Owner’s Guide • October 2005

About the System Controller Card and
RSC Software
The system controller (SC) card, combined with the Remote System Control (RSC)
software, enables access, monitoring, and control of the Sun Fire V890 server from a
remote location. It is a fully independent processor card with its own resident
firmware, power-on self-test (POST) diagnostics, and real-time operating system.
The card features serial and Ethernet interfaces that provide simultaneous access to
the Sun Fire V890 server for multiple RSC users. RSC users are provided secure
access to the system’s Solaris and OpenBoot console functions and have full control
over POST and OpenBoot Diagnostics.

The system controller card runs independently of the host server, and operates
on 5-volt standby power from the system’s power supplies. The card features
on-board devices that interface with the system’s environmental monitoring
subsystem and can automatically alert administrators to system problems.
Together these features allow the system controller card and RSC software to
serve as a “lights-out” management tool that continues to function even when
the server operating system goes offline or the system is powered off.

Chapter 3 Hardware Configuration 59

 The system controller card plugs in to a dedicated slot on the system I/O board
and provides the following ports through an opening in the system rear panel:
■ 10-Mbps Ethernet port via an RJ-45 twisted-pair Ethernet (TPE) connector
■ EIA-232D serial port via an RJ-45 connector

The two system controller ports can be used simultaneously.

Note – You must install the Solaris Operating System and the Sun Remote System
Control software prior to setting up an RSC console. For more information, see
“About Sun Remote System Control Software” on page 133.

Once you install the operating system and the RSC software, you can then configure
the system to use RSC as the system console. For detailed instructions, see “How to
Redirect the System Console to RSC” on page 42.

Configuration Rule
A qualified service technician can install the system controller card into a dedicated
slot at the base of the system I/O board. Never move the system controller card to
another system slot, as it is not a PCI-compatible card.

Note – The system controller card is not a hot-pluggable component. Before

installing or removing a system controller card, a qualified service technician must
power off the system and disconnect all system power cords.

Caution – All internal options (except disk drives and power supplies) must be
installed only by qualified service personnel. For information about installing or
removing the system controller card, see the Sun Fire V890 Server Service Manual,
which is included on the Sun Fire V890 Documentation CD.

60 Sun Fire V890 Server Owner’s Guide • October 2005

About Power Supplies
A central power distribution board delivers DC power to all internal system
components. The system’s power supplies plug in to connectors on this board, and
all of the supplies installed share equally in satisfying the power demands of the
system.

Sun Fire V890 power supplies are modular units, designed for fast, easy installation
or removal, even while the system is fully operational. Power supplies are installed
in bays at the rear of the system, as shown in the following figure.

Chapter 3 Hardware Configuration 61

 Power supply 2 Power supply 1 Power supply 0

62 Sun Fire V890 Server Owner’s Guide • October 2005

The system can accommodate a maximum of three power supplies, each with its
own 10-amp AC power cord. Each power supply provides up to 1629 watts of DC
power at 200-240 VAC line input. The basic system configuration comes with three
power supplies installed. The third power supply provides N+1 power redundancy,
allowing the system to continue operating should any one of the power supplies fail.

Each power supply provides a total of five DC output voltages (3.3V, 5.0V, 12V, 48V,
and 5.0V standby). Output current is shared equally between each of the supplies
via active current sharing circuitry.

Power supplies in a redundant configuration feature a hot-swap capability. You

can remove and replace a faulty power supply without shutting down the
operating system or turning off the system power. For additional details, see
“About Hot-Pluggable and Hot-Swappable Components” on page 127.

Each power supply has three status LEDs to provide power and fault status
information. For additional details, see “About Power Supply LEDs” on page 148.

Configuration Rules
■ Sun Microsystems recommends that you connect each power supply to a
dedicated AC circuit. Consult your local electrical codes for any additional
requirements.
■ The minimum system configuration requires two power supplies. The basic
system configuration comes with three power supplies installed. Systems
configured with only one power supply are not supported.
■ A system configured with two power supplies may shut down abruptly if either
power supply fails. The third power supply enables the system to remain fully
operational should any one of the power supplies fail.
■ Power supply bays 0 and 1 must always contain power supplies. If a power
supply in either bay fails and the system can continue to operate, you must leave
the failed power supply in its bay until you are able to install a functioning
replacement power supply. A failed power supply in bay 0 or 1 still acts as an air
baffle, channeling airflow to cool the bottom row of disk drives in the disk cage.
The failed power supply should be replaced as soon as possible to regain N+1
power redundancy.

Caution – If any power supply fails, leave the supply in its bay until you are ready
to install a replacement.

For information about installing power supplies, see the Sun Fire V890 Server Service
Manual, which is included on the Sun Fire V890 Documentation CD.

Chapter 3 Hardware Configuration 63

 About Fan Trays
The basic system is equipped with three fan trays: a CPU fan tray, an I/O fan tray,
and a motherboard fan tray. The CPU and I/O fan trays contain two fans apiece,
while the motherboard fan tray contains a single fan. All systems are equipped with
this primary set of fan trays and redundant cooling from a secondary set of the same
fan trays.

The motherboard fan tray is also known as the I/O bridge fan tray since its primary
purpose is to cool the I/O bridge chips on the system motherboard.

The following table describes the system’s fan trays.

Fan(s) Bay Description

Primary CPU fan tray 1 One fan tray with two 6-inch fans
Secondary CPU fan tray 2 One fan tray with two 6-inch fans
Primary I/O fan tray 3 One fan tray with two 4-inch fans
Secondary I/O fan tray 4 One fan tray with two 4-inch fans
Primary motherboard fan tray 5 One 3-inch fan
Secondary motherboard fan tray 6 One 3-inch fan

64 Sun Fire V890 Server Owner’s Guide • October 2005

 Secondary motherboard fan tray
Primary I/O fan tray Secondary I/O fan tray
Primary
Primary motherboard
CPU fan tray fan tray

Secondary
CPU fan tray

Only the primary fan trays are running during normal system operation. If a
primary fan tray fails, the environmental monitoring subsystem detects the failure
and automatically activates the secondary fan tray.

All fan trays feature a hot-swap capability. Qualified service technicians can remove
and replace a faulty fan tray without shutting down the operating system or turning
off the system power. For additional details, see “About Hot-Pluggable and Hot-
Swappable Components” on page 127.

For each fan in the system, the environmental monitoring subsystem monitors or
controls the following:
■ Fan present (monitored)
■ Fan speed in revolutions per minute (RPM) (monitored) – Used to detect early fan
degradation
■ Fan power input (controlled) – Used to increase or decrease the airflow and
cooling capacity
■ Fan fault LEDs (controlled)

Chapter 3 Hardware Configuration 65

 Only the primary CPU fans have variable speed control. The secondary CPU fans,
the primary and secondary motherboard fans, and the primary and secondary I/O
fans can only be turned fully on or fully off. Fan speed is controlled by the
environmental monitoring subsystem in response to temperature conditions inside
the system. For additional details, see “Environmental Monitoring and Control” on
page 17.

Status indicator LEDs provide power, fault, and hot-swap indications for each fan
tray. For information about the status indicator LEDs, see “About Fan Tray LEDs” on
page 152.

Caution – All internal options (except disk drives and power supplies) must be
installed only by qualified service technicians. For information about installing or
removing fan tray assemblies, see the Sun Fire V890 Server Service Manual, which is
included on the Sun Fire V890 Documentation CD.

Configuration Rules
■ The minimum system configuration requires a complete set of three working fan
trays—an I/O fan tray, a CPU fan tray, and a motherboard fan tray.
■ If the system does not include a secondary CPU fan tray, a CPU fan tray filler
panel must be installed in its place.

Caution – A complete set of three working fan trays must be present in the system
at all times. After removing a fan tray, if the system is left with fewer than three
working fan trays, a qualified service technician must install a replacement fan tray
immediately to avoid an automatic thermal shutdown. For more information, see
“Environmental Monitoring and Control” on page 17.

66 Sun Fire V890 Server Owner’s Guide • October 2005

About Removable Media Devices
The Sun Fire V890 system provides front-panel access to three mounting bays. One
bay houses an IDE DVD-ROM drive, which comes standard in all system
configurations. The other two bays can house optional wide (68-pin) SCSI removable
devices, which must be ordered separately. The tape drive option also requires a
SCSI cable and a SCSI adapter card; both must be ordered separately. A qualified
service technician can easily convert the two SCSI device bays into a single full-
height bay by removing a metal shelf divider.

The SCSI bus that supports the removable media devices is Fast/Wide-capable
(20 Mbytes per second) and can support single-ended, wide SCSI devices.

Target addresses (also know as SCSI IDs) for the SCSI bus are available in the ranges
of 0 through 5 and 8 through 15.

The target address reserved for the optional tape drive is 5.

If no tape drive is installed, you can use this address for an external device. If you
later install an internal tape drive, you must use 5 as its address and assign a
different address to the external device.

Caution – All internal options (except disk drives and power supplies) must be
installed only by qualified service personnel. For information about installing or
removing removable media devices, see the Sun Fire V890 Server Service Manual,
which is included on the Sun Fire V890 Documentation CD.

About the Serial Ports

The system provides two serial communication ports through a single, shared DB-25
connector located on the rear panel. The primary port is capable of both
synchronous and asynchronous communication, while the secondary port is
asynchronous only. In synchronous mode, the primary port operates at any rate
from 50 Kbaud to 256 Kbaud when the clock is generated internally. When the clock
is generated from an external source, the synchronous port operates at rates up to
384 Kbaud. In asynchronous mode, either port supports baud rates of 50, 75, 110,
200, 300, 600, 1200, 1800, 2400, 4800, 9600, 19200, 38400, 57600, 76800, 115200, 153600,
230400, 307200, and 460800.

Chapter 3 Hardware Configuration 67

 The primary port is accessible by connecting a standard serial cable to the rear panel
serial port connector. To access the secondary port, you must attach a serial port
splitter cable (Sun part number X985A) to the rear panel serial port connector. The
connector labeled “A” on the splitter cable provides the primary port; the connector
labeled “B” provides the secondary port.

A qualified service technician can configure both serial ports to comply with the
Electronics Industries Association EIA-423 or EIA-232D standards using jumpers
located on the system’s I/O board. The jumpers are factory-set for the EIA-423
standard, which is the default standard for North American users. Compliance with
the EIA-232D standard is required for digital telecommunication in nations of the
European Community. For more information about configuring the serial port
jumpers, see “” on page 71.

See “Reference for the Serial Port A and B Connectors” on page 176 for the connector
diagram, rear panel icon, and pin assignments.

About the USB Ports

The system’s rear panel provides two Universal Serial Bus (USB) ports for
connection to USB peripheral devices such as:
■ Sun Type-6 USB keyboard
■ Sun USB three-button mouse
■ Modems
■ Printers
■ Scanners
■ Digital cameras

For USB port locations, see “Locating Rear Panel Features” on page 9.

Note – For Sun Fire V890 servers, you must order the keyboard and mouse as
options. If the version of your Sun Type 6 keyboard does not have an integrated USB
hub, the keyboard and mouse will consume both USB ports on the system rear
panel. If you need to connect additional USB devices, you must add a USB hub.

The USB ports are compliant with the Open Host Controller Interface (Open
HCI) specification for USB Revision 1.0. Both ports support isochronous and
asynchronous modes and enable data transmission at speeds of 1.5 Mbps
and 12 Mbps. Note that the USB data transmission speed is significantly
faster than that of the standard serial ports, which operate at a maximum
rate of 460 Kbaud.

68 Sun Fire V890 Server Owner’s Guide • October 2005

The USB ports are accessible by connecting a USB cable to either rear panel USB
connector. The connectors at each end of a USB cable are different, so you cannot
connect them incorrectly. One connector plugs in to the system or USB hub; the other
plugs in to the peripheral device. Up to 126 USB devices can be connected to the bus
simultaneously, through the use of USB hubs.

Note – The Universal Serial Bus provides power for smaller USB devices such as
modems. Larger USB devices, such as scanners, require their own power source.

Both USB ports support hot-plugging. You can connect and disconnect the USB cable
and peripheral devices while the system is running, without affecting system
operations.

Note – You can only perform USB hot-plug operations while the operating system is
running. USB hot-plug operations are not supported when the system ok prompt is
displayed.

About Hardware Jumpers

The hardware jumpers in the Sun Fire V890 server have the following functions:
■ J2902 and J2903 on the system I/O board are used to configure the serial ports for
either EIA-423 or EIA-232D operation. For information about the EIA-423 and
EIA-232D jumper settings, see “” on page 71.
■ J3002, J3003, and J3004 are used to affect the operation of the OpenBoot flash
PROM located on the system I/O board. See “About Flash PROM Jumpers” on
page 72.
■ J01701, J01003, and J0803 are used to affect the operation of the flash PROM
located on the FC-AL disk backplane. See “About Flash PROM Jumpers” on
page 72.

Caution – All internal jumper modifications must be performed only by qualified

service personnel.

Caution – Do not change the configuration of J0501 and J0502 on the system
controller card from the default settings; otherwise, the system controller card will
not boot.

Chapter 3 Hardware Configuration 69

 All jumpers are marked with identification numbers. For example, the serial port
jumpers on the system I/O board are marked J2902 and J2903. Jumper pins are
located immediately adjacent to the identification number. The default jumper
positions are indicated with shaded regions. Pin 1 is marked with an asterisk (*) in
any of the positions shown below.

J 2XXX Jumper number

Pins

* * Asterisk indicates pin 1

* * Shaded region indicates

default jumper position
* *

About Serial Port Jumpers

The serial port jumpers (J2902 and J2903) on the system I/O board configure the
system’s two serial ports for either EIA-423 or EIA-232D signal levels. EIA-423 levels
are the default standard for North American users. EIA-232D levels are required for
digital telecommunication in nations of the European Community.

70 Sun Fire V890 Server Owner’s Guide • October 2005

 J2902
J2903

Jumper Shunt on Pins 1 + 2 Selects Shunt on Pins 2 + 3 Selects Default Setting

EIA-232D EIA-423 2+3

EIA-232D EIA-423 2+3

Chapter 3 Hardware Configuration 71

 About Flash PROM Jumpers
The Sun Fire V890 system uses flash PROMs to enable the reprogramming of specific
firmware code blocks held in nonvolatile system memory, and to enable remote
reprogramming of that code by an authorized system administrator over a local area
network. Firmware updates, when required, are available for download from the
SunSolve Online web site at http://sunsolve.sun.com.

Instructions for performing a firmware update procedure are provided with the
downloaded firmware image.

Several jumpers located on the system I/O board and FC-AL disk backplane affect
flash PROM operation. The jumper locations and settings are provided in the
sections that follow. For an explanation of how each jumper affects the flash PROM
update procedure, see the instructions supplied with the firmware image.

System I/O Board

The locations and functions of the flash PROM jumpers on the system I/O board are
shown below.

72 Sun Fire V890 Server Owner’s Guide • October 2005

 J3004
J3003
J3002

Jumper Shunt on Pins 1 + 2 Selects Shunt on Pins 2 + 3 Selects Default Setting

OpenBoot flash PROM For factory use only 1+2

Write-protect Write-enable 2+3

High half booting Normal booting 2+3

Chapter 3 Hardware Configuration 73

 Note – Jumper J3003 is factory-set so that the flash PROM is write-enabled. You use
the keyswitch located on the front panel to write-protect the flash PROM. When the
switch is set to the Locked position, the flash PROM is write-protected. When the
switch is set to the Normal position or to the Diagnostics position, the flash PROM is
write-enabled.

FC-AL Disk Backplane

The locations and functions of the flash PROM jumpers on the Fibre
Channel-Arbitrated Loop (FC-AL) disk backplane are shown below.

74 Sun Fire V890 Server Owner’s Guide • October 2005

J01701

J0803

J01003

Jumper Shunt on Pins 1 + 2 Selects Shunt on Pins 2 + 3 Selects Default Setting

High half booting, Loop B Normal booting, Loop B 2+3

High half booting, Loop A Normal booting, Loop A 2+3

Flash PROM For factory use only 1+2

Chapter 3 Hardware Configuration 75

76 Sun Fire V890 Server Owner’s Guide • October 2005
CHAPTER 4

Mass Storage Subsystem

Configuration

This chapter describes the features of the Sun Fire V890 mass storage subsystem, its
components, and supported configurations. The following topics are covered in this
chapter:
■ “About FC-AL Technology” on page 77
■ “About Sun Fire V890 Mass Storage Features” on page 79
■ “About the Mass Storage Subsystem Components” on page 80
■ “About the FC-AL Disk Backplanes” on page 82
■ “About Internal Disk Drives” on page 84
■ “About FC-AL Host Adapters” on page 86
■ “About FC-AL Device Addresses” on page 88

About FC-AL Technology

Fibre Channel (FC) is a high-performance serial interconnect standard designed for
bidirectional, point-to-point communication among servers, storage systems,
workstations, switches, and hubs.

Fibre Channel-Arbitrated Loop (FC-AL) is an important enhancement to the FC

standard, developed specifically to meet the needs of storage system interconnects.
Employing a simple loop topology, FC-AL can support both simple configurations
and complex arrangements of hubs, switches, servers, and storage systems.

FC-AL devices employ a high-performance Gigabit serial interface, which supports

multiple standard protocols such as Small Computer Systems Interface (SCSI) and
Asynchronous Transfer Mode (ATM). By supporting these standard protocols,
FC-AL preserves any investment in existing legacy systems, firmware, applications,
and software.

77
 The unique features of FC-AL provide many advantages over other data transfer
technologies. The following table lists the features and advantages of FC-AL. For
additional information about FC-AL technology, visit the Fibre Channel Association
web site at http://www.fibrechannel.com.

FC-AL Features Advantages

Supports 100-Mbyte per second data transfer High throughput meets the demands of current
rate (200 Mbytes per second with dual generation high-performance processors and
porting) disks.
Capable of addressing up to 126 devices, High connectivity controlled by one device
plus a single controller, per loop allows flexible and simpler configurations.
Supports distances up to 10 km between Long distances between devices offers
devices using fiber-optic cable (up to 30 improved data availability by allowing remote
meters using copper cable) mirroring and campus clustering.
Provides for reliability, availability, and RAS features provide improved fault tolerance
serviceability (RAS) features such as hot- and data availability.
pluggable and dual-ported disks, redundant
data paths, and multiple host connections
Supports standard protocols such as IP and Migration to FC-AL produces small or no
SCSI impact on software and firmware.
Implements a simple serial protocol over Configurations that use serial connections are
copper or fiber cable less complex because of the reduced number of
cables per connection.
Supports redundant array of independent RAID support enhances data availability.
disks (RAID)

78 Sun Fire V890 Server Owner’s Guide • October 2005

About Sun Fire V890 Mass Storage
Features
The FC-AL technology implemented in the Sun Fire V890 mass storage subsystem
significantly enhances the server’s reliability, availability, and serviceability (RAS)
and performance capabilities.

The following table describes Sun Fire V890 mass storage subsystem features that
enhance RAS capabilities.

Features RAS Capabilities

Dual-ported FC-AL disk drives, These features provide fault tolerance and high
dual-loop backplanes, and availability of data. You can implement automatic
multiple FC-AL host adapters failover by configuring up to four independent and
redundant data paths using up to four FC-AL host
adapters and appropriate multipathing software. If a
component in any path fails, the software
automatically detects the failure and switches all data
transfers to an alternate path. For additional details,
see “About Multipathing Software” on page 131.
Support for RAID software Using a software RAID application (like Solstice
DiskSuite), you can ensure high availability of data
through fault tolerance and data redundancy. For more
information, see “About Volume Management
Software” on page 134.
Hot-pluggable disk drives Hot-pluggable disk drives ensure high data
availability and enhanced serviceability. You can
quickly replace a failed disk drive in a powered-on
system, without affecting the rest of the system’s
capabilities. For more information, see “About Internal
Disk Drives” on page 84 and “About Hot-Pluggable
and Hot-Swappable Components” on page 127.

Chapter 4 Mass Storage Subsystem Configuration 79

 The following table describes the performance features of the Sun Fire V890 mass
storage subsystem.

Features Performance Enhancements

Dual-ported FC-AL disk drives, These features enable simultaneous access to the
dual-loop backplanes, and internal storage array via two separate loops. When
multiple FC-AL host adapters combined with volume management software that
takes advantage of the Sun Fire V890 server’s
multipathing capability, disk throughput can be
increased. For additional details, see “About the FC-
AL Disk Backplanes” on page 82 and “About Volume
Management Software” on page 134.
Support for RAID levels 0, 0+1, When configured with optional RAID software, the
1+0, and 5 Sun Fire V890 system supports RAID levels 0, 0+1,
1+0, and 5, which incorporate disk striping. Disk
striping distributes contiguous blocks of data across
multiple disks. This speeds up data access by enabling
multiple disk controllers to access the data
simultaneously. For additional information, see
“About Volume Management Software” on page 134.

About the Mass Storage Subsystem

Components
All Sun Fire V890 servers include the following mass storage subsystem
components.

Component Quantity Description

FC-AL disk backplane 1 Base backplane providing connections for up to

six dual-ported FC-AL disk drives. See “About
the FC-AL Disk Backplanes” on page 82.
On-board FC-AL host 1 Integrated into the system motherboard.
adapter Manages FC-AL I/O operations and data
transfers on Loop A of the mass storage
subsystem. See “About FC-AL Host Adapters”
on page 86.

80 Sun Fire V890 Server Owner’s Guide • October 2005

The following mass storage subsystem components are available as system options.

Component Quantity Description

Expansion FC-AL disk 1 Expands the base array to accommodate up to 12

backplane disks. See “About the FC-AL Disk Backplanes”
on page 82.
FC-AL disk drives Up to 12 Low-profile (1.0-inch) dual-ported disks,
(6 per available in various storage capacities. See
backplane) “About Internal Disk Drives” on page 84.
PCI FC-AL host adapter Up to 9 PCI host adapter cards for controlling internal or
cards external FC-AL devices. These plug in to PCI
slots on the system I/O board. Up to three PCI
FC-AL host adapters can be connected internally
to manage FC-AL I/O operations and data
transfers on Loops A and B of the mass storage
subsystem. See “About FC-AL Host Adapters”
on page 86.

Chapter 4 Mass Storage Subsystem Configuration 81

 About the FC-AL Disk Backplanes
All Sun Fire V890 servers include a single FC-AL disk backplane with connections
for up to six disks. An optional expansion backplane may be installed above the base
backplane to accommodate up to six additional disks.

Front view Rear view

The FC-AL backplane accepts low-profile (1.0-inch) dual-ported FC-AL disk drives.
Each disk drive connects to the backplane via a standard 40-pin single connector
attachment (SCA) interface. Incorporating all power and signal connections into a
single, blind-mating connector, SCA technology makes it easy to add or remove disk
drives from the system. Disks using SCA connectors provide higher availability and
better serviceability than disks using other types of connectors.

82 Sun Fire V890 Server Owner’s Guide • October 2005

Dual-Loop Configurations
The FC-AL disk backplane provides dual-loop access to all internal disk drives, in
both full and split backplane configurations (see “Full vs. Split Backplane
Configurations” on page 83). Dual-loop configurations enable each disk drive to be
accessed through two separate and distinct data paths. This capability provides:
■ Increased bandwidth – Allowing data transfer rates up to 200 Mbytes per second
versus 100 Mbytes per second for single-loop configurations
■ Hardware redundancy – Providing the ability to sustain component failures in one
path by switching all data transfers to an alternate path

For more information on the RAS and performance capabilities of the mass storage
subsystem, see “About Sun Fire V890 Mass Storage Features” on page 79.

Note – To take advantage of the dual-loop capability of the FC-AL backplanes, an

optional PCI FC-AL host adapter card must be installed to control the second loop
(Loop B). For more information, see “About FC-AL Host Adapters” on page 86.

Port bypass controllers (PBCs) on the disk backplane ensure loop integrity. When a
disk or external device is unplugged or fails, the PBCs automatically bypass the
device, closing the loop to maintain data availability.

Each backplane also includes two integrated SSC100 SCSI Enclosure Services (SES)
controllers, one for each loop. The SES controllers:
■ Interpret enclosure service commands from the host software
■ Manage the backplane’s FC-AL loop configuration
■ Monitor status signals from disks and disk backplanes
■ Control disk status LEDs

When a second backplane is installed to form an expanded 12-disk array, only the
SES controllers on the base backplane are active; the SES controllers on the upper
backplane remain inactive.

Full vs. Split Backplane Configurations

In the expanded 12-disk array, the two FC-AL disk backplanes are connected by
internal cables. These cables extend Loop A (and optionally, Loop B) between the
two backplanes. This is sometimes called a full backplane configuration. The dual-loop,
full backplane configuration provides redundancy of disks, data paths, and host
adapters.

Chapter 4 Mass Storage Subsystem Configuration 83

 It is also possible to set up a split backplane configuration, in which, unlike the full
backplane configuration, there is no cabling between the base and expansion
backplanes. In the dual-loop, split backplane configuration, there are four
independent loops, two on each backplane; this provides redundancy of disks, data
paths, host adapters, and backplanes.

Split backplane configurations must be set up by a qualified service technician. For

details, see the “Split Backplane Configurations” appendix in the Sun Fire V890
Server Service Manual.

Configuration Rules
■ The FC-AL disk backplane requires low-profile (1.0-inch) disk drives.
■ The optional expansion disk backplane is installed above the base backplane.

Caution – All internal options (except disk drives and power supplies) must be
installed only by qualified service personnel. For information about installing or
removing an FC-AL disk backplane, see the Sun Fire V890 Server Service Manual,
which is included on the Sun Fire V890 Documentation CD.

About Internal Disk Drives

The Sun Fire V890 mass storage subsystem accommodates up to 12 low-profile
(1.0-inch) FC-AL disk drives. Disks are available in various storage capacities. .

All Sun Fire V890 disk drives are dual-ported for multipath access. When used in a
dual-loop configuration, each drive can be accessed through two separate and
distinct data paths. Dual data paths provide the following benefits:

84 Sun Fire V890 Server Owner’s Guide • October 2005

■ Increased bandwidth – Allowing data transfer rates up to 200 Mbytes per second
versus 100 Mbytes per second for single-loop configurations
■ Hardware redundancy – Providing the ability to sustain component failures in one
path by switching all data transfers to an alternate path

For more information on the RAS and performance capabilities of the mass storage
subsystem, see “About Sun Fire V890 Mass Storage Features” on page 79.

Sun Fire V890 disk drives are hot-pluggable. You can add, remove, or replace disks
while the system continues to operate. This capability significantly reduces system
downtime associated with disk drive replacement. Disk drive hot-plug procedures
involve software commands for preparing the system prior to removing a disk drive
and for reconfiguring the operating system after installing a drive. For additional
details, see “About Hot-Pluggable and Hot-Swappable Components” on page 127.

At the front of the system disk cage are several disk drive status LEDs. There are
three LEDs associated with each drive, indicating the drive’s operating status,
hot-plug readiness, and any fault conditions associated with the drive. These status
LEDs help administrators to quickly identify drives requiring service. For additional
details, see “About Disk Drive LEDs” on page 156.

The following figure shows the system’s 12 internal disk slots and associated LEDs.
Disk slots are labeled from 0 to 11.

Chapter 4 Mass Storage Subsystem Configuration 85

 Configuration Rule
Disk drives must be Sun standard FC-AL disks with low-profile (1.0-inch) form
factors.

About FC-AL Host Adapters

The Sun Fire V890 server uses a Qlogic ISP2200A intelligent Fibre Channel processor
as its on-board FC-AL controller. Integrated into the system motherboard, the
ISP2200A resides on PCI Bus A and supports a 64-bit, 66-MHz PCI interface. The
on-board FC-AL controller controls FC-AL operations on Loop A of the base
backplane (and the upper backplane when the two are joined as an expanded array).

To take advantage of the dual-loop capability of the FC-AL backplanes, an optional

PCI FC-AL host adapter card is required to control the second loop (Loop B). For
this purpose, Sun offers the Sun StorEdge PCI Dual Fibre Channel Host Adapter
card (part number X6727A). This card provides two separate FC-AL channels, each
controlled by a Qlogic ISP2200A processor. Each channel provides an external port
for connection to external Fibre Channel devices. One of the channels also provides
an internal port for connection to the Loop B port on the base FC-AL disk backplane.
If the internal port is used, external Port 1 is unavailable for connection to external
devices.

Loop A
ISP
SES

SES

Expansion Backplane

Motherboard
SES

ISP SES
Loop B
ISP
Base Backplane
Sun StorEdge PCI
Dual Fibre Channel
Host Adapter Card

86 Sun Fire V890 Server Owner’s Guide • October 2005

To provide additional hardware redundancy, two split backplane configurations are
available as field-installed options. See the “Split Backplane Configurations”
appendix in the Sun Fire V890 Server Service Manual.

A variety of PCI FC-AL host adapter cards are available from Sun Microsystems and
other vendors for controlling external FC-AL devices. These include dual-channel
cards and combination cards. Dual-channel cards contain two FC-AL controllers for
controlling two separate loops with a single card. Combination cards combine an
FC-AL controller with a controller of another type (for example, a Gigabit Ethernet
controller). For more information, see the documentation supplied with the host
adapter card.

Sun StorEdge PCI Dual Fibre Channel Host Adapter Card

Configuration Rules
■ The Sun Fire V490 server supports Sun FC-AL host adapter cards that incorporate
the Qlogic ISP2200 series intelligent Fibre Channel processor. Sun host adapter
cards that use the Qlogic ISP2100 series processor are not supported. For a list of
supported cards, contact your authorized Sun sales representative.
■ If your system is configured with a Sun StorEdge PCI Dual Fibre Channel Host
Adapter card, and its internal port is connected to the Loop B port of the FC-AL
disk backplane, you must not use the card’s external Port 1. Connecting Port 1 to
external devices under these circumstances is considered an unsupported
configuration. In this case, use only Port 2 to connect to external devices.
■ Do not use the internal port of the Sun StorEdge PCI Dual Fibre Channel Host
Adapter card to connect to the Loop A port of the FC-AL disk backplane. You
must connect the card’s internal port to Loop B only.
■ For best performance, install 66-MHz FC-AL host adapter cards in a 66-MHz PCI
slot (slot 7 or 8, if available). See “About PCI Cards and Buses” on page 56.

Chapter 4 Mass Storage Subsystem Configuration 87

 Caution – All internal options (except disk drives and power supplies) must be
installed only by qualified service personnel. For information about installing or
removing a PCI FC-AL host adapter card, see the Sun Fire V890 Server Service
Manual, which is included on the Sun Fire V890 Documentation CD.

About FC-AL Device Addresses

In a Sun Fire V890 internal storage array, each FC-AL device is assigned a unique
selection ID based on its physical location in the storage array. Each slot on the disk
backplane is hard-wired to a different selection ID.

Each FC-AL disk drive is connected directly to a Fibre Channel loop and appears as
a separate node on the loop. Each node on a loop is assigned a unique arbitrated
loop physical address (AL_PA), one of 127 available addresses per loop.

AL_PA values may be hard-assigned or soft-assigned and are determined when the
loop is initialized—typically when booting the system or when adding or removing
a device as part of a hot-plug operation. Hard-assigned AL_PAs are established first,
according to the selection ID for each device. If, for any reason, there are conflicts
with hard-assigned addresses during loop initialization, the devices involved
automatically revert to soft-assigned addresses to resolve the conflicts.

The AL_PA values that are hard-assigned to each device depend on the device’s
location within its backplane (disk slot number). The following table shows the
selection IDs and AL_PA values that are hard-assigned to Sun Fire V890 internal
FC-AL devices, depending on the device location. Both selection IDs and AL_PA
values are expressed as hexadecimal numbers.

Base Backplane Sel ID AL_PA Expansion Backplane Sel ID AL_PA

Disk 0 00 EF Disk 6 08 D9
Disk 1 01 E8 Disk 7 09 D6
Disk 2 02 E4 Disk 8 0A D5
Disk 3 03 E2 Disk 9 0B D4
Disk 4 04 E1 Disk 10 0C D3
Disk 5 05 E0 Disk 11 0D D2
SES processor 06 DC

88 Sun Fire V890 Server Owner’s Guide • October 2005

CHAPTER 5

Configuring Network Interfaces

This chapter describes the networking options of the system and provides
information and instructions required to plan and configure the supported network
interfaces.

Tasks covered in this chapter include:

■ “How to Configure the Primary Network Interface” on page 92
■ “How to Configure Additional Network Interfaces” on page 94
■ “How to Attach a Fiber-Optic Gigabit Ethernet Cable” on page 97
■ “How to Attach a Twisted-Pair Ethernet Cable” on page 99
■ “How to Select the Boot Device” on page 101

Other information covered in this chapter includes:

■ “About Network Interfaces” on page 90
■ “About Redundant Network Interfaces” on page 91

89
 About Network Interfaces
The Sun Fire V890 server provides two on-board Ethernet interfaces—one Gigabit
Ethernet and one Fast Ethernet interface. The 100BASE-TX Fast Ethernet interface is
located on the system I/O board and conforms to the IEEE 802.3u Ethernet standard.
The Fast Ethernet interface is an auto-sensing, switchable interface that can operate
at 100 Mbps or 10 Mbps. It negotiates automatically with the remote end of the link
(link partner) to select a common mode of operation.

The 1000BASE-SX Gigabit Ethernet interface resides on the system motherboard and
conforms to the IEEE 802.3z Ethernet standard. The Gigabit Ethernet interface
operates at 1000 Mbps only.

Two rear panel connectors provide access to the on-board Ethernet interfaces:
■ One 1000BASE-SX compliant SC connector for connecting 62.5/125-micron or
50/125-micron fiber-optic cable to the Gigabit Ethernet interface
■ One RJ-45 connector for connecting Category-5 twisted-pair Ethernet (TPE) cable
to the Fast Ethernet interface

Additional Ethernet interfaces or connections to other network types are available

by installing the appropriate PCI interface cards. A Gigabit Ethernet or Fast Ethernet
PCI card can serve as a redundant network interface for one of the system’s on-
board interfaces. If the active network interface becomes unavailable, the system can
automatically switch to the redundant interface to maintain availability. This
capability is known as automatic failover and must be configured at the Solaris
Operating System level. For additional details, see “About Redundant Network
Interfaces” on page 91.

The ge Gigabit Ethernet driver, the eri Fast Ethernet driver, and drivers for several
other network interfaces are installed automatically during the Solaris installation
procedure. For more information, see the Solaris documentation included with your
software.

For instructions on configuring the system’s network interfaces, see:

■ “How to Configure the Primary Network Interface” on page 92
■ “How to Configure Additional Network Interfaces” on page 94

90 Sun Fire V890 Server Owner’s Guide • October 2005

About Redundant Network Interfaces
You can configure your system with redundant network interfaces to provide a
highly available network connection. Such a configuration relies on special Solaris
software features to detect a failed or failing network interface and automatically
switch all network traffic over to the redundant interface. This capability is known
as automatic failover.

To set up redundant network interfaces, you can enable automatic failover

between the two similar interfaces using the multipathing feature of the Solaris
Operating System. For additional details, see “About Multipathing Software” on
page 131. A qualified service technician can also install a pair of identical PCI
network interface cards, or add a single card that provides an interface identical
to one of the two on-board Ethernet interfaces.

To help maximize system availability, make sure that any redundant network
interfaces reside on separate PCI buses, supported by separate PCI bridges. For
additional details, see “About PCI Cards and Buses” on page 56.

Chapter 5 Configuring Network Interfaces 91

 How to Configure the Primary Network
Interface

Before You Begin

You must perform the following tasks:
■ Complete the installation steps in “How to Install the Sun Fire V890 Server” on
page 24.
■ Attach a cable to the appropriate network connector on the system rear panel; see
“How to Attach a Fiber-Optic Gigabit Ethernet Cable” on page 97 or “How to
Attach a Twisted-Pair Ethernet Cable” on page 99.

If you are using a PCI network interface card, see the documentation supplied with
the card.

Note – All internal options (except disk drives and power supplies) must be
installed only by qualified service personnel. Installation procedures for these
components are covered in the Sun Fire V890 Server Service Manual, which is
included on the Sun Fire V890 Documentation CD.

What to Do
1. Choose a host name for the system.
The host name must be unique within the network. It can consist only of
alphanumeric characters and the dash (-). Do not use a dot in the host name. Do not
begin the name with a number or a special character. The name must not be longer
than 30 characters.

2. Determine the unique Internet Protocol (IP) address of the network interface and
make a note of it.
You need to furnish the address in a later step.
An IP address must be assigned by your network administrator. Each network
device or interface must have a unique IP address.

3. Resume the installation of the system.

Return to “How to Install the Sun Fire V890 Server” on page 24.

92 Sun Fire V890 Server Owner’s Guide • October 2005

Note – During installation of the Solaris Operating System, the software
automatically detects the system’s on-board network interfaces and any installed
PCI network interface cards for which native Solaris device drivers exist. The
operating system then asks you to select one of the interfaces as the primary
network interface and prompts you for its host name and IP address. You can
configure only one network interface during installation of the operating system.
You must configure any additional interfaces separately, after the operating system
is installed. For more information, see “How to Configure Additional Network
Interfaces” on page 94.

What Next
After completing this procedure, the primary network interface is ready for
operation. However, in order for other network devices to communicate with the
system, you must enter the system’s IP address and host name into the namespace
on the network name server. For information about setting up a network name
service, consult:
■ Solaris Naming Configuration Guide for your specific Solaris release

The device driver for the system’s on-board Sun GigaSwift Ethernet interfaces is
automatically installed with the Solaris release. For information about operating
characteristics and configuration parameters for this driver, refer to the following
document:
■ Platform Notes: The Sun GigaSwift Ethernet Device Driver

This document is available at http://docs.sun.com, under Solaris on Sun

Hardware. Refer also to the Sun Fire V890 Server Product Notes for late-breaking
details.

If you want to set up an additional network interface, you must configure it

separately, after installing the operating system. See:
■ “How to Configure Additional Network Interfaces” on page 94

Note – The Sun Fire V890 system conforms to the Ethernet 10/100BASE-T standard,
which states that the Ethernet 10BASE-T link integrity test function should always
be enabled on both the host system and the Ethernet hub. If you have problems
establishing a connection between this system and your hub, verify that the Ethernet
hub also has the link integrity test function enabled. Consult the manual provided
with your hub for more information about the link integrity test function.

Chapter 5 Configuring Network Interfaces 93

 How to Configure Additional Network
Interfaces

Before You Begin

Perform the following tasks to prepare an additional network interface:
■ Install the Sun Fire V890 server as described in “How to Install the Sun Fire V890
Server” on page 24.
■ If you are setting up a redundant network interface, see “About Redundant
Network Interfaces” on page 91.
■ If you need to install a PCI network interface card, follow the installation
instructions in the Sun Fire V890 Server Service Manual.
■ Attach an Ethernet cable to the appropriate port on the system rear panel; see
“How to Attach a Fiber-Optic Gigabit Ethernet Cable” on page 97 or “How to
Attach a Twisted-Pair Ethernet Cable” on page 99.

If you are using a PCI network interface card, see the documentation supplied with
the card.

Note – All internal options (except disk drives and power supplies) must be
installed only by qualified service personnel. Installation procedures for these
components are covered in the Sun Fire V890 Server Service Manual, which is
included on the Sun Fire V890 Documentation CD.

What to Do
1. Choose a network host name for each new interface.

The host name must be unique within the network. It can consist of alphanumeric
characters and the dash (-). Do not use a dot in the host name. Do not begin the
name with a number or a special character.

Usually an interface host name is based on the machine host name. For example, if
the machine is assigned the host name sunrise, the added network interface could
be named sunrise-1. The machine’s host name is assigned when Solaris software
is installed. For more information, see the installation instructions accompanying the
Solaris software.

94 Sun Fire V890 Server Owner’s Guide • October 2005

2. Determine the IP address for each new interface.
An IP address must be assigned by your network administrator. Each interface on a
network must have a unique IP address.

3. Boot the operating system (if it is not already running) and log on to the system as
superuser.
Be sure to perform a reconfiguration boot if you just added a new PCI network
interface card. See “How to Initiate a Reconfiguration Boot” on page 40.
Type the su command at the system prompt, followed by the superuser password.

$ su
Password:

4. Create an appropriate /etc/hostname file for each new network interface.

The name of the file you create should be of the form /etc/hostname.typenum,
where type is the network interface type identifier (some common types are le, hme,
eri, and ge) and num is the device instance number of the interface according to the
order in which it was installed in the system.
For example, the file names for the system’s on-board Fast Ethernet and Gigabit
Ethernet interfaces are /etc/hostname.eri0 and /etc/hostname.ge0,
respectively. Both interfaces have a device instance number of 0 since each interface
is the first one of its type installed in the system. If you add a PCI Gigabit Ethernet
adapter card as a second ge interface, it’s file name should be /etc/hostname.ge1.
At least one of these files—the primary network interface—should exist already,
having been created automatically during the Solaris installation process.

Note – The documentation accompanying the network interface card should

identify its type. Alternatively, you can enter the show-devs command from the ok
prompt to obtain a list of all installed devices.

5. Edit the /etc/hostname file(s) created in Step 4 to add the host name(s)
determined in Step 1.
Following is an example of the /etc/hostname files required for a system called
sunrise, which has two on-board Ethernet interfaces (ge0 and eri0) and a PCI
Gigabit Ethernet adapter card (ge1). A network connected to the on-board eri0

Chapter 5 Configuring Network Interfaces 95

 interface will know the system as sunrise, while networks connected to the ge0
and ge1 interfaces will know the system as sunrise-1 and sunrise-2,
respectively.

sunrise # cat /etc/hostname.eri0

sunrise
sunrise # cat /etc/hostname.ge0
sunrise-1
sunrise # cat /etc/hostname.ge1
sunrise-2

6. Create an entry in the /etc/hosts file for each active network interface.
An entry consists of the IP address and the host name for each interface.

The following example shows an /etc/hosts file with entries for the three network
interfaces used as examples in this procedure.

sunrise # cat /etc/hosts

#
# Internet host table
#
127.0.0.1 localhost
129.144.10.57 sunrise loghost
129.144.14.26 sunrise-1
129.144.11.83 sunrise-2

7. Manually plumb and enable each new interface using the ifconfig command.
For example, for the logical interface ge0, type:

sunrise # ifconfig ge0 plumb up

For more information, see the ifconfig(1M) man page.

What Next
After completing this procedure, any new network interfaces are ready for
operation. However, in order for other network devices to communicate with the
system through the new interface, the IP address and host name for each new
interface must be entered into the namespace on the network name server. For
information about setting up a network name service, consult
■ Solaris Naming Configuration Guide for your specific Solaris release

96 Sun Fire V890 Server Owner’s Guide • October 2005

The eri and ge device drivers for the system’s on-board Ethernet interfaces are
automatically configured during Solaris installation. For information about
operating characteristics and configuration parameters for these drivers, refer to the
following documents:
■ Platform Notes: The eri FastEthernet Device Driver
■ Platform Notes: The Sun GigabitEthernet Device Driver

These documents are available with your Solaris software and online at
http://docs.sun.com, under Solaris on Sun Hardware. Refer also to the Sun
Fire V890 Server Product Notes for late-breaking information.

Note – The Sun Fire V890 system conforms to the Ethernet 10/100BASE-T standard,
which states that the Ethernet 10BASE-T link integrity test function should always
be enabled on both the host system and the Ethernet hub. If you have problems
establishing a connection between this system and your Ethernet hub, verify that the
hub also has the link test function enabled. Consult the manual provided with your
hub for more information about the link integrity test function.

How to Attach a Fiber-Optic Gigabit

Ethernet Cable

Before You Begin

Complete the prerequisite steps in:
■ “How to Install the Sun Fire V890 Server” on page 24

Chapter 5 Configuring Network Interfaces 97

 What to Do
1. Select a fiber-optic cable that meets all Sun Fire V890 cabling requirements.
The Sun Fire V890 on-board Gigabit Ethernet interface supports 50/125-micron or
62.5/125-micron multimode, duplexed, fiber-optic cable. The cable must meet UL910
and UL1651 specifications and must have a standard dual SC connector with a
UL94V-2 rating (or better).
Cable lengths must not exceed 300 meters for 62.5/125-micron cable, or 550 meters
for 50/125-micron cable.
If your system includes a PCI Gigabit Ethernet adapter card, see the documentation
supplied with the card for cable requirements.

2. Locate the dual SC connector for the Gigabit Ethernet interface.

See “Locating Rear Panel Features” on page 9. For a PCI Gigabit Ethernet adapter
card, see the documentation supplied with the card.

3. Remove any dust covers from the SC connectors.

4. Connect the fiber-optic cable to the Gigabit Ethernet connector and to the Ethernet
network.
The cable and connector are keyed for correct mating orientation.

98 Sun Fire V890 Server Owner’s Guide • October 2005

 What Next
If you are installing your system, complete the installation procedure. Return to:
■ “How to Install the Sun Fire V890 Server” on page 24

If you are adding an additional network interface to the system, then you need to
configure that interface. See:
■ “How to Configure Additional Network Interfaces” on page 94

How to Attach a Twisted-Pair Ethernet

Cable

Before You Begin

Complete the prerequisite steps in:
■ “How to Install the Sun Fire V890 Server” on page 24

What to Do
1. Locate the RJ-45 twisted-pair Ethernet (TPE) connector for the appropriate Fast
Ethernet interface.
See “Locating Rear Panel Features” on page 9. For a PCI Fast Ethernet adapter card,
see the documentation supplied with the card.

2. Plug in a Category-5 unshielded twisted-pair (UTP) cable to the appropriate RJ-45

connector.
You should hear the connector tab click into place. The UTP cable length must not
exceed 100 meters (328 feet).

Chapter 5 Configuring Network Interfaces 99

 3. Connect the other end of the cable to the RJ-45 outlet to the appropriate network
device.
You should hear the connector tab click into place.

Consult your network administrator if you need more information about how to
connect to your network.

What Next
If you are installing your system, complete the installation procedure. Return to:
■ “How to Install the Sun Fire V890 Server” on page 24

If you are adding an additional network interface to the system, then you need to
configure that interface. See:
■ “How to Configure Additional Network Interfaces” on page 94

100 Sun Fire V890 Server Owner’s Guide • October 2005

 How to Select the Boot Device
The boot device is specified by the setting of an OpenBoot firmware configuration
variable called boot-device. The default setting of this variable is disk net.
Because of this setting, the firmware first attempts to boot from the system hard
drive, and if that fails, from the on-board Fast Ethernet interface.

Before You Begin

Before you can select a boot device, you must complete the installation procedure.
See:
■ “How to Install the Sun Fire V890 Server” on page 24

Specifically, you must set up a system console and power on the system. See:
■ “How to Attach an Alphanumeric Terminal” on page 31
■ “How to Configure a Local Graphics Console” on page 33
■ “How to Power On the System” on page 35

If you want to boot from a network, you must also connect the network interface to
the network and configure the network interfaces. See:
■ “How to Attach a Twisted-Pair Ethernet Cable” on page 99
■ “How to Configure the Primary Network Interface” on page 92
■ “How to Configure Additional Network Interfaces” on page 94

This procedure assumes that you are familiar with the OpenBoot firmware and that
you know how to enter the OpenBoot environment. For more information about the
OpenBoot firmware, see the OpenBoot 4.x Command Reference Manual, which is
available at http://docs.sun.com, under Solaris on Sun Hardware. Refer also to
the Sun Fire V890 Server Product Notes for late-breaking details.

What to Do
1. At the ok prompt, type:

ok setenv boot-device device-specifier

where the device-specifier is one of the following:

■ cdrom – Specifies the CD-ROM drive
■ disk – Specifies the system boot disk

Chapter 5 Configuring Network Interfaces 101

 ■ disk0 – Specifies internal disk 0
■ disk1 – Specifies internal disk 1
■ disk2 – Specifies internal disk 2
■ disk3 – Specifies internal disk 3
■ disk4 – Specifies internal disk 4
■ disk5 – Specifies internal disk 5
■ disk6 – Specifies internal disk 6
■ disk7 – Specifies internal disk 7
■ disk8 – Specifies internal disk 8
■ disk9 – Specifies internal disk 9
■ disk10 – Specifies internal disk 10
■ disk11 – Specifies internal disk 11
■ tape – Specifies the SCSI tape drive (if present)
■ net – Specifies the on-board Fast Ethernet interface
■ gem – Specifies the on-board Gigabit Ethernet interface
■ full path name – Specifies the device or network interface by its full path name

Note – You can also specify the name of the program to be booted as well as the
way the boot program operates. For more information, see the OpenBoot 4.x
Command Reference Manual for your specific Solaris software.

If you want to specify a network interface other than an on-board Ethernet interface
as the default boot device, you can determine the full path name of each interface by
typing:

ok show-devs

The show-devs command lists the system devices and displays the full path name
of each PCI device. An example of a path name for a Fast Ethernet PCI card is shown
below:

/pci@8,700000/pci@2/SUNW,hme@0,1

2. To cause variable changes to take effect, type:

ok reset-all

Note – To store variable changes, you can also power cycle the system using the
front panel Power button.

102 Sun Fire V890 Server Owner’s Guide • October 2005

CHAPTER 6

Configuring System Firmware

This chapter describes the OpenBoot firmware commands and configuration

variables available for configuring the following aspects of the Sun Fire V890
system behavior:
■ OpenBoot environmental monitoring
■ Automatic system recovery (ASR)

In addition, this chapter provides information about keyboard commands and

alternative methods for performing OpenBoot emergency procedures.

Tasks covered in this chapter include:

■ “How to Enable OpenBoot Environmental Monitoring” on page 106
■ “How to Disable OpenBoot Environmental Monitoring” on page 107
■ “How to Obtain OpenBoot Environmental Status Information” on page 108
■ “How to Enable ASR” on page 113
■ “How to Disable ASR” on page 114
■ “How to Deconfigure a Device Manually” on page 116
■ “How to Reconfigure a Device Manually” on page 117
■ “How to Obtain ASR Status Information” on page 118
■ “How to Implement Stop-N Functionality” on page 121

Other information covered in this chapter includes:

■ “About OpenBoot Environmental Monitoring” on page 104
■ “About Automatic System Recovery” on page 109
■ “About Manually Configuring Devices” on page 114
■ “About OpenBoot Emergency Procedures” on page 119
■ “Reference for Device Identifiers” on page 123

Note – To enhance system restoration and server availability, Sun has recently
introduced a new standard (default) OpenBoot firmware configuration. These
changes, which affect the behavior of servers like the Sun Fire V890, are described in
OpenBoot PROM Enhancements for Diagnostic Operation. This document is included on
the Sun Fire V890 Documentation CD.

103
 Note – The procedures in this chapter assume that you are familiar with the
OpenBoot firmware and that you know how to enter the OpenBoot environment.
For more information about the OpenBoot firmware, see the OpenBoot 4.x Command
Reference Manual, which is available at http://docs.sun.com, under Solaris on
Sun Hardware. Refer to the Sun Fire V890 Server Product Notes for late-breaking
details.

About OpenBoot Environmental

Monitoring
Environmental monitoring and control capabilities for Sun Fire V890 systems reside
at both the operating system level and the OpenBoot firmware level. This ensures
that monitoring capabilities are operational even if the system has halted or is
unable to boot. Whenever the system is under OpenBoot control, the OpenBoot
environmental monitor checks the state of the system power supplies, fans, and
temperature sensors every 30 seconds. If it detects any voltage, current, fan speed, or
temperature irregularities, the monitor generates a warning message to the system
console. In the event of a critical fan failure or overtemperature condition, the
monitor generates a shutdown warning and automatically powers off the system
after 30 seconds to prevent hardware damage.

For additional information about the system’s environmental monitoring

capabilities, see “Environmental Monitoring and Control” on page 17.

Enabling or Disabling the OpenBoot

Environmental Monitor
The OpenBoot environmental monitor is enabled by default whenever the system is
operating at the ok prompt. However, you can enable or disable it yourself using the
OpenBoot commands env-on and env-off. For more information, see:
■ “How to Enable OpenBoot Environmental Monitoring” on page 106
■ “How to Disable OpenBoot Environmental Monitoring” on page 107

104 Sun Fire V890 Server Owner’s Guide • October 2005

Note – Using the Stop-A keyboard command to enter the OpenBoot environment
will immediately disable the OpenBoot environmental monitor. If you want the
OpenBoot environmental monitor enabled, you must re-enable it prior to rebooting
the system. If you enter the OpenBoot environment through any other means—by
halting the operating system, by power-cycling the system, or as a result of a system
panic—the OpenBoot environmental monitor will remain enabled.

Automatic System Shutdown

If the OpenBoot environmental monitor detects a critical fan failure or
overtemperature condition, it will initiate an automatic system shutdown sequence.
In this case, a warning similar to the following is generated to the system console:

WARNING: SYSTEM POWERING DOWN IN 30 SECONDS!

Press Ctrl-C to cancel shutdown sequence and return to ok prompt.

If necessary, you can type Control-C to abort the automatic shutdown and return to
the system ok prompt; otherwise, after the 30 seconds expire, the system will power
off automatically.

Note – Typing Control-C to abort an impending shutdown also has the effect of
disabling the OpenBoot environmental monitor. This gives you enough time to
replace the component responsible for the critical condition without triggering
another automatic shutdown sequence. After replacing the faulty component, you
must type the env-on command to reinstate OpenBoot environmental monitoring.

Caution – If you type Control-C to abort an impending shutdown, you should

immediately replace the component responsible for the critical condition. If a
replacement part is not immediately available, power off the system to avoid
damaging system hardware.

OpenBoot Environmental Status Information

The OpenBoot command .env lets you obtain status on the current state of
everything of interest to the OpenBoot environmental monitor. You can obtain
environmental status at any time, regardless of whether OpenBoot environmental

Chapter 6 Configuring System Firmware 105

 monitoring is enabled or disabled. The .env status command simply reports the
current environmental status information; it does not take action if anything is
abnormal or out of range.

For an example of .env command output, see “How to Obtain OpenBoot

Environmental Status Information” on page 108.

How to Enable OpenBoot Environmental

Monitoring
The OpenBoot environmental monitor is enabled by default whenever the system is
operating at the ok prompt. However, you can enable or disable it yourself using the
OpenBoot commands env-on and env-off.

Note – The commands env-on and env-off only affect environmental monitoring
at the OpenBoot level. They have no effect on the system’s environmental
monitoring and control capabilities while the operating system is running.

Before You Begin

This procedure assumes that you are familiar with the OpenBoot firmware and that
you know how to enter the OpenBoot environment. For more information about the
OpenBoot firmware, see the OpenBoot 4.x Command Reference Manual, which is
available at http://docs.sun.com, under Solaris on Sun Hardware. Refer to the
Sun Fire V890 Server Product Notes for late-breaking details.

What to Do
● To enable OpenBoot environmental monitoring, type env-on at the system ok
prompt.

ok env-on
Environmental monitor is ON
ok

106 Sun Fire V890 Server Owner’s Guide • October 2005

 How to Disable OpenBoot
Environmental Monitoring
The OpenBoot environmental monitor is enabled by default whenever the system is
operating at the ok prompt. However, you can enable or disable it yourself using the
OpenBoot commands env-on and env-off.

Note – The commands env-on and env-off only affect environmental monitoring
at the OpenBoot level. They have no effect on the system’s environmental
monitoring and control capabilities while the operating system is running.

Note – Using the Stop-A keyboard command to enter the OpenBoot environment
will immediately disable the OpenBoot environmental monitor. You must then
re-enable the environmental monitor prior to rebooting the system. If you enter the
OpenBoot environment through any other means—by halting the operating system,
by power-cycling the system, or as a result of a system panic—the OpenBoot
environmental monitor will remain enabled.

What to Do
● To disable OpenBoot environmental monitoring, type env-off at the system ok
prompt.

ok env-off
Environmental monitor is OFF
ok

Chapter 6 Configuring System Firmware 107

 How to Obtain OpenBoot
Environmental Status Information
You can use the OpenBoot command .env at the system ok prompt to obtain status
information about the system’s power supplies, fans, and temperature sensors.

What to Do
● To obtain OpenBoot environmental status information, type .env at the system ok
prompt.

ok .env
Environmental Status:

Power Supplies:
PS0: Present, receiving AC power
PS1: Present, receiving AC power
PS2: Present, receiving AC power

Fans:
Tray 1 (CPU): Present, Fan A @ 3225 RPM, Fan B @ 3157 RPM
Tray 2 (CPU): Present, Fan A @ 3529 RPM, Fan B @ 3571 RPM
Tray 3 (I/O): Present, Fan A @ 3529 RPM, Fan B @ 3488 RPM
Tray 4 (I/O): Present, Fan A @ 3157 RPM, Fan B @ 3030 RPM
Fan 5 (IO-Bridge): Present, Fan @ 3846 RPM
Fan 6 (IO-Bridge): Present, Fan @ 3658 RPM

Temperatures:
CMP0: Ambient = 32 deg. C, Die = 56 deg. C
CMP1: Ambient = 34 deg. C, Die = 52 deg. C
CMP2: Ambient = 31 deg. C, Die = 52 deg. C
CMP3: Ambient = 33 deg. C, Die = 57 deg. C
CMP4: Ambient = 36 deg. C, Die = 59 deg. C
CMP5: Ambient = 32 deg. C, Die = 53 deg. C
CMP6: Ambient = 33 deg. C, Die = 59 deg. C
CMP7: Ambient = 32 deg. C, Die = 56 deg. C
Motherboard: Ambient = 22 deg. C
I/O Board: Ambient = 19 deg. C
Disk Backplane 0: Ambient = 19 deg. C

Environmental monitor is ON

108 Sun Fire V890 Server Owner’s Guide • October 2005

Note – You can obtain environmental status at any time, regardless of whether
OpenBoot environmental monitoring is enabled. The .env status command simply
reports the current environmental status information; it does not take action if
anything is abnormal or out of range.

About Automatic System Recovery

To some, automatic system recovery (ASR) implies an ability to shield the operating
system in the event of a hardware failure, allowing the operating system to remain
up and running. The implementation of ASR on the Sun Fire V890 server is different.
ASR on the Sun Fire V890 server provides for automatic fault isolation and
restoration of the operating system following non-fatal faults or failures of these
hardware components:
■ Processors
■ Memory modules
■ PCI buses and cards
■ IDE bus
■ FC-AL subsystem
■ Fast Ethernet interface
■ Gigabit Ethernet interface
■ USB interface
■ Serial interfaces

In the event of such a hardware failure, firmware-based diagnostic tests isolate the
problem and mark the device (using the 1275 Client Interface, via the device tree) as
either failed or disabled. The OpenBoot firmware then deconfigures the failed device
and reboots the operating system. This all occurs automatically, as long as the Sun
Fire V890 system is capable of functioning without the failed component.

Once restored, the operating system will not attempt to access any deconfigured
device. This prevents a faulty hardware component from keeping the entire system
down or causing the system to crash repeatedly.

As long as the failed component is electrically dormant (that is, it does not cause
random bus errors or introduce noise into signal lines), the system reboots
automatically and resumes operation. Be sure to contact a qualified service
technician about replacing the failed component.

Chapter 6 Configuring System Firmware 109

 Auto-Boot Options
The auto-boot? OpenBoot configuration variable controls whether the operating
system boots after each reset. The default setting for Sun platforms is true.

Note – The system will not boot automatically when it is in service mode. For
details, see “Reset Scenarios” on page 112.

If a system fails power-on diagnostics, then auto-boot? is ignored and the system
does not start up unless an operator boots the system manually. This behavior
obviously provides limited system availability. Therefore, the Sun Fire V890
OpenBoot firmware provides a second OpenBoot configuration variable switch
called auto-boot-on-error?. This switch controls whether the system will
attempt to boot when a subsystem failure is detected.

Both the auto-boot? and auto-boot-on-error? switches must be set to true

(their default values) to enable an automatic boot following the firmware detection
of a non-fatal subsystem failure.

ok setenv auto-boot? true

ok setenv auto-boot-on-error? true

The system will not attempt to boot if it is in service mode, or following any fatal
non-recoverable error. For examples of fatal non-recoverable errors, see “Error
Handling Summary” on page 111.

110 Sun Fire V890 Server Owner’s Guide • October 2005

 Error Handling Summary
Error handling during the power-on sequence falls into one of three cases
summarized in the following table.

Scenario System Behavior Notes

No errors are The system attempts to boot if By default, auto-boot? and auto-boot-on-
detected auto-boot? is true. error? are both true.
Non-fatal errors are The system attempts to boot if Non-fatal errors include:
detected auto-boot? and auto-boot-on- • IDE bus failure
error? are both true. • FC-AL subsystem failure 1
• Gigabit or Fast Ethernet interface failure
• USB interface failure
• Serial interface failure
• PCI card failure
• Processor failure 2
• Memory failure 3
Fatal non-recoverable The system will not boot regardless Fatal non-recoverable errors include:
errors are detected of OpenBoot configuration variable • All processors failed
settings. • All logical memory banks failed
• Flash RAM cyclical redundancy check
(CRC) failure
• Critical FRU-ID SEEPROM configuration
data failure
• Critical application specific integrated
circuit (ASIC) failure

1. A working alternate path to the boot disk is required. For more information, see “About Multipathing Software” on page 131.
2. A single processor failure causes the entire CPU/Memory module to be deconfigured. Reboot requires that another functional
CPU/Memory module be present.
3. Since each physical DIMM belongs to two logical memory banks, the firmware deconfigures both memory banks associated with the
affected DIMM. This leaves the CPU/Memory module operational, but with one of the processors having a reduced complement of
memory.

Note – If POST or OpenBoot Diagnostics detects a non-fatal error associated with

the normal boot device, the OpenBoot firmware automatically deconfigures the
failed device and tries the next-in-line boot device, as specified by the boot-device
configuration variable.

Chapter 6 Configuring System Firmware 111

 Reset Scenarios
The system keyswitch position and two OpenBoot configuration variables,
diag-switch? and diag-trigger, control whether and how the system runs
firmware diagnostics in response to system reset events.

When you set the system keyswitch to the Diagnostics position, the system is in
service mode and runs tests at Sun-specified levels, ignoring the settings of
OpenBoot configuration variables.

Setting the diag-switch? variable to true also puts the system in service mode,
producing exactly the same results as setting the system keyswitch to the Diagnostics
position.

Note – Auto-booting is disabled when the system is in service mode.

When you set the system keyswitch to the Normal position, and when the OpenBoot
diag-switch? variable is set to false (its default value), the system is in normal
mode. When the system is in this mode, you can control diagnostics and auto-boot
behavior by setting OpenBoot configuration variables, principally diag-trigger.

The following table describes the various settings (keywords) of the diag-trigger
variable. You can use the first three of these keywords in any combination.

Keyword Function

power-on-reset Reset caused by power-cycling the system.

(default)
error-reset Reset caused by certain hardware error events, such as a RED State
(default) Exception, Watchdog Reset, or Fatal Resets.
user-reset Reset caused by operating system panics or by user-initiated
commands from OpenBoot (reset-all, boot) or from Solaris OS
(reboot, shutdown, init).
none Diagnostic tests are not executed.

Normal Mode and Service Mode Information

You will find a full description of normal and service modes, as well as detailed
information about the OpenBoot configuration variables that affect ASR behavior, in
OpenBoot PROM Enhancements for Diagnostic Operation, which is available on the
Sun Fire V890 Documentation CD.

112 Sun Fire V890 Server Owner’s Guide • October 2005

 ASR User Commands
The OpenBoot commands .asr, asr-disable, and asr-enable are available for
obtaining ASR status information and for manually deconfiguring or reconfiguring
system devices. For more information, see:
■ “How to Deconfigure a Device Manually” on page 116
■ “How to Reconfigure a Device Manually” on page 117
■ “How to Obtain ASR Status Information” on page 118

How to Enable ASR

The automatic system recovery (ASR) feature is enabled by default when the system
is in normal mode. However, if you have edited the OpenBoot configuration
variables controlling ASR, follow this procedure to restore them. See “Reset
Scenarios” on page 112 for more information.

What to Do
1. Type the following at the system ok prompt:

ok setenv diag-switch? false

ok setenv auto-boot? true
ok setenv auto-boot-on-error? true

2. Set the diag-trigger and diag-script variables as shown. Type:

ok setenv diag-trigger power-on-reset error-reset

ok setenv diag-script normal

The system permanently stores the parameter changes.

Chapter 6 Configuring System Firmware 113

 How to Disable ASR
To disable the automatic system recovery (ASR) feature, either place the system in
service mode, or edit OpenBoot configuration variables as described in this
procedure. See “Reset Scenarios” on page 112 for more information.

What to Do
● Type the following at the system ok prompt:

ok setenv auto-boot-on-error? false

The system permanently stores the parameter change.

About Manually Configuring Devices

This section explains the difference between deconfiguring a device and a slot, tells
what happens if you try to deconfigure all of a system’s processors, and also
discusses how to obtain device paths.

Deconfiguring Devices vs. Slots

For some devices, different things happen when you deconfigure a slot than when
you deconfigure the device that resides within a slot.

If you deconfigure a PCI device, the device in question can still be probed by
firmware and recognized by the operating system. Solaris OS “sees” such a device,
reports it as failed, and refrains from using it.

If you deconfigure a PCI slot, firmware will not even probe the slot, and the
operating system will not “know about” any devices that may be plugged into the
slot.

114 Sun Fire V890 Server Owner’s Guide • October 2005

In both cases, the devices in question are rendered unusable. So why make the
distinction? Occasionally, a device may fail in such a way that probing it disrupts the
system. In cases such as these, deconfiguring the slot in which the device resides is
more likely to contain the problem.

Deconfiguring All System Processors

You can use the asr-disable command to deconfigure all system processors.
Doing this will not crash the system. The OpenBoot system firmware, even though it
reports all processors as deconfigured, in actuality keeps one processor functioning
well enough to run the firmware.

Device Paths
When manually deconfiguring and reconfiguring devices, you might need to
determine the full physical paths to those devices. You can do this by typing:

ok show-devs

The show-devs command lists the system devices and displays the full path name
of each device. An example of a path name for a Fast Ethernet PCI card is shown
below:

/pci@8,700000/pci@2/SUNW,hme@0,1

You can display a list of current device aliases by typing:

ok devalias

You can also create your own device alias for a physical device by typing:

ok devalias alias_name physical_device_path

Chapter 6 Configuring System Firmware 115

 where alias_name is the alias that you want to assign, and physical_device_path is the
full physical device path for the device.

Note – If you manually deconfigure a device alias using asr-disable, and then
assign a different alias to the device, the device will remain deconfigured even
though the device alias has changed.

You can determine which devices are currently disabled by typing:

ok .asr

See “How to Obtain ASR Status Information” on page 118.

The related deconfiguration and reconfiguration procedures are covered in:

■ “How to Deconfigure a Device Manually” on page 116
■ “How to Reconfigure a Device Manually” on page 117

Device identifiers are listed in:

■ “Reference for Device Identifiers” on page 123

How to Deconfigure a Device Manually

To support the ability to boot even when nonessential components fail, the
OpenBoot firmware provides the asr-disable command, which lets you manually
deconfigure system devices. This command “marks” a specified device as disabled,
by creating an appropriate “status” property in the corresponding device tree node.
By convention, UNIX will not activate a driver for any device so marked.

What to Do
1. At the ok prompt, type:

ok asr-disable device-identifier

where the device-identifier is one of the following:

■ Any full physical device path as reported by the OpenBoot show-devs command
■ Any valid device alias as reported by the OpenBoot devalias command
■ An identifier for a device given in “Reference for Device Identifiers” on page 123

116 Sun Fire V890 Server Owner’s Guide • October 2005

 Note – Manually deconfiguring a single processor causes the entire CPU/Memory
board to be deconfigured, including both processors and all memory residing on the
board.

OpenBoot configuration variable changes take effect after the next system reset.

2. To effect the changes immediately, type:

ok reset-all

Note – To immediately effect the changes, you can also power cycle the system
using the front panel Power button.

How to Reconfigure a Device Manually

You can use the OpenBoot asr-enable command to reconfigure any device that
you previously deconfigured with asr-disable.

What to Do
1. At the ok prompt, type:

ok asr-enable device-identifier

where the device-identifier is one of the following:

■ Any full physical device path as reported by the OpenBoot show-devs command
■ Any valid device alias as reported by the OpenBoot devalias command
■ An identifier for a device or a range of devices given in “Reference for Device
Identifiers” on page 123

2. Do one of the following:

a. If you are reconfiguring a processor, power cycle the system using the front
panel Power button.

Chapter 6 Configuring System Firmware 117

 b. If you are reconfiguring any other device, type:

ok reset-all

Note – To reconfigure a processor, you must power cycle the system. The
reset-all command will not suffice to bring the processor back online.

How to Obtain ASR Status Information

What to Do
● Type the following at the system ok prompt:

ok .asr
ASR Disablement Status
Component: Status

CMP0: Enabled
Memory Bank0: Disabled
Memory Bank1: Enabled
Memory Bank2: Enabled
Memory Bank3: Enabled
CMP1/Memory: Enabled
CMP2/Memory: Enabled
CMP3/Memory: Enabled
CMP4/Memory: Enabled
CMP5/Memory: Enabled
CMP6/Memory: Enabled
CMP7/Memory: Enabled
IO-Bridge8: Enabled
IO-Bridge9: Enabled
GPTwo Slots: Enabled
Onboard SCSI: Enabled
Onboard FCAL: Enabled
Onboard GEM: Enabled
PCI Slots: Enabled

The following devices have been ASR disabled:

/pci@8,700000/TSI,gfxp@5

118 Sun Fire V890 Server Owner’s Guide • October 2005

In the .asr command output, any devices marked disabled have been manually
deconfigured using the asr-disable command. In this example, the .asr output
shows that one of the memory banks controlled by CMP 0, as well as the frame
buffer card in PCI slot 0, have been deconfigured.

Note – The .asr command only shows devices that have been manually disabled
using the asr-disable command. It does not show devices that have been
automatically deconfigured as a result of failing firmware diagnostics. To see which
devices, if any, have failed POST diagnostics, use the show-post-results
command, as described in Sun Fire V890 Diagnostics and Troubleshooting. You can find
this document at: http://www.sun.com/documentation.

For more information, see:

■ “About Automatic System Recovery” on page 109
■ “How to Enable ASR” on page 113
■ “How to Disable ASR” on page 114
■ “How to Deconfigure a Device Manually” on page 116
■ “How to Reconfigure a Device Manually” on page 117

About OpenBoot Emergency Procedures

The following paragraphs describe the functions of the Stop commands on systems
that use USB keyboards, such as the Sun Fire V890 system.

Stop-A Functionality
Stop-A (Abort) issues a break that drops the system into OpenBoot firmware control
(indicated by the display of the ok prompt). The key sequence works the same on
the Sun Fire V890 server as it does on systems with older keyboards, except that it
does not work during the first few seconds after the machine is reset.

Stop-D Functionality
The Stop-D (diags) key sequence is not supported on systems with USB keyboards.
However, the Stop-D functionality can be closely emulated by turning the system
keyswitch to the Diagnostics position. For more information, see “About the Status
and Control Panel” on page 11.

Chapter 6 Configuring System Firmware 119

 The RSC bootmode diag command also provides similar functionality. For more
information, see the Sun Remote System Control (RSC) 2.2 User’s Guide, which is
included on the Sun Fire V890 Documentation CD.

Stop-F Functionality
The Stop-F functionality is not available in systems with USB keyboards. However,
the RSC bootmode forth command provides similar functionality. For more
information, see the Sun Remote System Control (RSC) 2.2 User’s Guide, which is
included on the Sun Fire V890 Documentation CD.

Stop-N Functionality
The Stop-N sequence is a method of bypassing problems typically encountered on
systems with misconfigured OpenBoot configuration variables. On systems with
older keyboards, you did this by pressing the Stop-N sequence while powering on
the system.

On systems with USB keyboards, like the Sun Fire V890, the implementation is
somewhat more cumbersome, and involves waiting for the system to reach a
particular state. For instructions, see “How to Implement Stop-N Functionality” on
page 121.

The drawback of using Stop-N on a Sun Fire V890 system is that, if diagnostics are
enabled, it can take some time for the system to reach the desired state. Fortunately,
an alternative exists: Place the system keyswitch in Diagnostics position.

Placing the system keyswitch in Diagnostics position will override OpenBoot

configuration variable settings, allowing the system to recover to the ok prompt and
letting you correct misconfigured settings.

Assuming you have access to RSC software, another possibility is to use the RSC
bootmode reset_nvram command, which provides similar functionality. For more
information, see the Sun Remote System Control (RSC) User’s Guide, which is included
on the Sun Fire V890 Documentation CD.

120 Sun Fire V890 Server Owner’s Guide • October 2005

 How to Implement Stop-N Functionality

Before You Begin

This procedure implements Stop-N functionality on Sun Fire V890 systems,
temporarily resetting OpenBoot configuration variables to their default settings. This
procedure is most useful if you have not configured your Sun Fire V890 system to
run diagnostic tests. You might find it more convenient to use the alternative method
of placing the system keyswitch in Diagnostics position. For more background, see:
■ “About OpenBoot Emergency Procedures” on page 119

For information about the system keyswitch, see:

■ “About the Status and Control Panel” on page 11

What To Do
1. Turn on the power to the system.
If POST diagnostics are configured to run, both the Fault and OK-to-Remove LEDs
on the front panel will blink slowly.

2. Wait until only the system Fault LED begins to blink rapidly.

Note – If you have configured the Sun Fire V890 system to run diagnostic tests, this
could take upwards of 30 minutes.

Chapter 6 Configuring System Firmware 121

 3. Press the front panel Power button twice, with no more than a short, one-second
delay in between presses.
A screen similar to the following is displayed to indicate that you have temporarily
reset OpenBoot configuration variables to their default values:

Setting NVRAM parameters to default values.

Probing I/O buses

Sun Fire V890, No Keyboard

Copyright 1998-2004 Sun Microsystems, Inc. All rights reserved.
OpenBoot x.x, xxxx MB memory installed, Serial #xxxxxxxx.
Ethernet address x:x:x:x:x:x, Host ID: xxxxxxxx.

System is operating in Safe Mode and initialized with factory

default configuration. No actual NVRAM configuration variables
have been changed; values may be displayed with ’printenv’ and set
with ’setenv’. System will resume normal initialization and
configuration after the next hardware or software reset.

ok

Note – Once the front panel LEDs stop blinking and the Power/OK LED stays lit,
pressing the Power button again will begin a graceful shutdown of the system.

What Next
During the execution of OpenBoot firmware code, all OpenBoot configuration
variables—including the ones that are likely to cause problems, such as input and
output device settings—are temporarily set to “safe” factory default values. The
only exception to this is auto-boot, which is set to false.

By the time the system displays the ok prompt, OpenBoot configuration variables
have been returned to their original, and possibly misconfigured, values. These
values do not take effect until the system is reset. You can display them with the
printenv command and manually change them with the setenv command.

If you do nothing other than reset the system at this point, no values are
permanently changed. All your customized OpenBoot configuration variable
settings are retained, even ones that may have caused problems.

122 Sun Fire V890 Server Owner’s Guide • October 2005

 To correct such problems, you must either manually change individual OpenBoot
configuration variables using the setenv command, or else type set-defaults to
permanently restore the default settings for all OpenBoot configuration variables.

Reference for Device Identifiers

Refer to the following table when manually specifying which devices to deconfigure
and reconfigure. The related procedures are covered in:
■ “How to Deconfigure a Device Manually” on page 116
■ “How to Reconfigure a Device Manually” on page 117

Device Identifiers Devices

cmpx, where x is a number 0–7, or 16–23. Particular processors

cmp0-bank0, cmp0-bank1, cmp0-bank2, cmp0-bank3, ... Memory banks 0–3 for each processor
cmp7-bank0, cmp7-bank1, cmp7-bank2, cmp7-bank3
gptwo-slotA, gptwo-slotB, gptwo-slotC, gptwo-slotD CPU/Memory board slots A–D
ob-gem On-board Gigabit Ethernet controller
ob-fcal On-board FC-AL controller
ob-ide On-board IDE controller
pci-slot0, pci-slot1, ... pci-slot8 PCI slots 0–8
hba8, hba9 PCI bridge chips 0 and 1, respectively

Note – The device identifiers above are not case-sensitive; you can type them as
uppercase or lowercase characters.

You can use wild cards within device identifiers to reconfigure a range of devices, as
shown in the following table.

Device Identifiers Devices

* All devices
cmp* All processors
cmp0-bank*, cmp1-bank*, ... cmp7-bank* All memory banks for each processor
hba* All PCI bridge chips
gptwo-slot* All CPU/Memory board slots
pci-slot* All PCI slots
pci* All on-board PCI devices (on-board Gigabit Ethernet,
FC-AL, and IDE controllers) and all PCI slots

Chapter 6 Configuring System Firmware 123

 Note – You cannot deconfigure a range of devices. Wild cards are valid only for
specifying a range of devices to reconfigure.

124 Sun Fire V890 Server Owner’s Guide • October 2005

CHAPTER 7

Server Administration

This chapter provides an introduction to server administration tools supported on

the Sun Fire V890 system. The following information is covered in this chapter:
■ “About Server Administration Software” on page 125
■ “About Hot-Pluggable and Hot-Swappable Components” on page 127
■ “About Multipathing Software” on page 131
■ “About Sun Management Center Software” on page 132
■ “About Sun Remote System Control Software” on page 133
■ “About Volume Management Software” on page 134
■ “About the Solaris luxadm Utility” on page 138
■ “About Sun Cluster Software” on page 139

About Server Administration Software

A number of software-based administration tools are available to help you configure
your system for performance and availability, monitor and manage your system, and
identify hardware problems. These administration tools include:
■ Solaris Dynamic Reconfiguration (DR) software
■ Multipathing software
■ Sun Management Center software
■ Sun Remote System Control (RSC) software
■ Volume management software
■ Solaris luxadm utility
■ Sun Cluster™ software

125
 The following table provides a summary of each tool with a pointer to additional
information.

Tool Description For More Information

Solaris Dynamic DR is used in conjunction with hot-plug See page 127.

Reconfiguration operations and provides the ability to logically
(DR) software and physically attach or detach hardware
resources (such as PCI cards) without impacting
normal system operations.
Multipathing Multipathing software is used to define and See page 131.
software control alternate (redundant) physical paths to
I/O devices. If the active path to a device
becomes unavailable, the software can
automatically switch to an alternate path to
maintain availability.
Sun Management Sun Management Center software is a See page 132.
Center software convenient, single solution for managing
multiple Sun servers, devices, and network
resources. With its simple Java™ technology-
based graphical interface, Sun Management
Center lets you manage and monitor servers
remotely from any location in the network. It
also provides access to real-time system
performance and configuration data, and helps
diagnose potential capacity problems and
performance bottlenecks.
Sun Remote System RSC is a remote management tool for See page 133.
Control (RSC) monitoring and controlling geographically
software distributed or physically inaccessible servers
over serial lines or an Ethernet network. RSC
software works in conjunction with the system
controller card in the Sun Fire V890 server to
serve as a “lights out” management tool that
continues to function even when the server
operating system goes offline or the server is
powered off.

126 Sun Fire V890 Server Owner’s Guide • October 2005

Tool Description For More Information

Volume Volume management applications such as See page 134.

management Solstice DiskSuite provide easy-to-use online
software disk storage management for enterprise
computing environments. Using advanced
RAID technology, these products ensure high
data availability, excellent I/O performance, and
simplified administration.
Solaris luxadm The Solaris luxadm utility is a command-line See page 138.
utility management tool for administering
Sun Fire V890 internal FC-AL disk subsystems
and attached external storage arrays. This utility
is used to perform physical disk management
tasks, including disk hot-plug operations.
Sun Cluster Sun Cluster software enables multiple Sun See page 139.
software servers to be interconnected so that they work
together as a single, highly available and
scalable system. Sun Cluster software delivers
high availability—through automatic fault
detection and recovery—and scalability,
ensuring that mission-critical applications and
services are always available when needed.

About Hot-Pluggable and

Hot-Swappable Components
Sun Fire V890 systems feature a variety of components that can be serviced while the
machine is running.

Hot-pluggable components are components that a qualified service technician can

install or remove while the system is running, without affecting the rest of the
system’s capabilities. However, in many cases, you must prepare the operating
system prior to the hot-plug event by performing certain system administration
tasks.

Components that can be serviced without such preparation are called hot-swappable
components. These components can be removed or inserted at any time without
preparing the operating system in advance.

Sun Fire V890 hot-pluggable components fall into three basic groups:
■ Fan trays and power supplies
■ Disk drives

Chapter 7 Server Administration 127

 ■ PCI cards

Each group is discussed in more detail in the sections that follow.

Note – PCI and disk hot-plug operations are not supported when the system ok
prompt is displayed. A qualified service technician can only perform these hot-plug
operations while the operating system is running.

Caution – The system controller (SC) card cannot be serviced while the system is
running. Before installing or removing a system controller card, you must power off
the system and disconnect all AC power cords.

Fan Trays and Power Supplies

Sun Fire V890 fan trays and power supplies are hot-swappable—they can be
removed or inserted at any time without requiring prior software preparations. Keep
in mind that a power supply is not considered hot-swappable unless it is part of an
N+1 redundant power configuration. Do not remove a power supply from a
working system if its removal would leave the system with fewer than two working
power supplies.

You can install or remove a power supply or fan tray while the system is operating
at the ok prompt. However, in the case of the power supply, you must issue a
reset-all command at the ok prompt in order for the change to be recognized the
next time the operating system is booted.

Note – If you remove a power supply or fan tray while the operating system is
running, wait for an acknowledgement message on the system console before
installing a replacement part; otherwise, the environmental monitoring software will
not recognize the new device and false error conditions will result.

Caution – When hot-swapping a redundant fan tray, do not put your hand into the
empty fan tray bay. The fans in the populated bay are still spinning.

For additional information, see:

■ “About Power Supplies” on page 61
■ “About Fan Trays” on page 64

128 Sun Fire V890 Server Owner’s Guide • October 2005

Disk Drives
Sun Fire V890 internal disk drives are hot-pluggable. However, certain software
preparations are required. To perform Sun Fire V890 disk drive hot-plug operations,
you use the Solaris luxadm utility. The luxadm utility is a command-line tool for
managing intelligent storage arrays such as Sun StorEdge™ A5x00 series disk arrays
or Sun Fire V890 internal storage arrays.

For more information about luxadm, see “About the Solaris luxadm Utility” on
page 138. For complete disk hot-plug procedures, refer to Platform Notes: Using
luxadm Software. This document is included on the Sun Fire V890 Documentation
CD. Refer also to the Sun Fire V890 Server Product Notes for late-breaking details.

Caution – When hot-plugging a disk drive, after disconnecting the drive from its
backplane, allow 30 seconds or so for the drive to spin down completely before
removing it from its drive bay.

PCI Cards
On Sun Fire V890 systems, PCI cards are hot-pluggable, while the system controller
card cannot be serviced when the machine is running.

Hot-plug operations for PCI cards involve Dynamic Reconfiguration (DR). DR is an

operating system feature that provides the ability to reconfigure system hardware
while the system is running. DR lets you logically attach or detach hardware
resources within an active operating system. The main benefit of DR is that a service
provider can add or replace hardware resources with little or no impact on normal
system operations.

PCI hot-plug procedures may involve software commands for preparing the system
prior to removing a device, and for reconfiguring the operating system after
installing a new device. In addition, certain system requirements must be met in
order for hot-plug operations to succeed.

For information about system requirements and limitations, and for detailed PCI
hot-plug procedures, refer to the Sun Fire V890 Dynamic Reconfiguration User’s Guide,
which is available at http://docs.sun.com, under Solaris on Sun Hardware.
Refer to the Sun Fire V890 Server Product Notes for late-breaking details.

Chapter 7 Server Administration 129

 Caution – A qualified service technician can hot-plug any standard PCI card that
complies with PCI Hot-Plug Specification Revision 1.1, provided a suitable software
driver exists for the Solaris OS, and the driver supports hot-plugging as described in
the Sun Fire V890 Dynamic Reconfiguration User’s Guide. The Sun Fire V890 system
must be running the Solaris 8 7/01 operating system or a subsequent release that
supports Sun Fire V890 PCI hot-plug operations. Do not attempt to hot-plug a PCI
card until you are certain that its device drivers provide the proper support;
otherwise, you may cause a system panic. For a list of Sun PCI cards and device
drivers that support PCI hot-plug operations, see the Sun Fire V890 Server Product
Notes.

Note – DR works in conjunction with (but does not require) multipathing software.
You can use multipathing software to switch I/O operations from one I/O controller
to another to prepare for DR operations. With a combination of DR and multipathing
software, a qualified service technician can remove, replace, or deactivate a PCI
controller card with little or no interruption to system operation. Note that this
requires redundant hardware; that is, the system must contain an alternate I/O
controller that is connected to the same device(s) as the card being removed or
replaced. The alternate controller must reside on a different PCI card or be
integrated into the Sun Fire V890 system motherboard or I/O board. For additional
details, see “About Multipathing Software” on page 131.

PCI Hot-Plug User Interfaces

There are two different methods for performing PCI hot-plug operations on
Sun Fire V890 systems:
■ Push-button method
■ Command-line method

The push-button method relies on push buttons and status LEDs located near each
PCI slot. A qualified service technician can initiate a PCI hot-plug operation by
pressing the push button for the corresponding slot. The command-line method lets
a qualified service technician initiate PCI hot-plug operations via a remote login
session, an RSC console, or a locally attached console. This method involves the
Solaris cfgadm(1) command.

Both hot-plug methods make use of the status LEDs located near each PCI slot.
These LEDs indicate where and when it is safe to insert or remove a card, and also
show whether the operation has succeeded or failed. For additional details on
hot-plug status LEDs, see “About PCI Slot LEDs” on page 144.

130 Sun Fire V890 Server Owner’s Guide • October 2005

Note – Regardless of the method you use, it is often necessary to perform additional
administrative steps to prepare for a PCI hot-plug removal operation. Prior to
performing a removal operation, you must ensure that the devices residing on the
card are not currently in use. To identify and manually terminate usage of such
devices, a system administrator can use standard Solaris OS commands such as
mount(1M), umount(1M), swap(1M), ifconfig(1M), and ps(1).

For More Information

For detailed PCI hot-plug procedures, refer to the Sun Fire V890 Dynamic
Reconfiguration User’s Guide, which is available at http://docs.sun.com, under
Solaris on Sun Hardware. Refer to the Sun Fire V890 Server Product Notes for late-
breaking details.

About Multipathing Software

Multipathing software lets you define and control redundant physical paths to I/O
devices such as storage devices and networks. If the active path to a device becomes
unavailable, the software can automatically switch to an alternate path to maintain
availability. This capability is known as automatic failover. To take advantage of
multipathing capabilities, your server must be configured with redundant hardware,
such as redundant network interfaces or two FC-AL host bus adapters connected to
the same dual-ported storage array.

Multipathing software is often used in conjunction with Solaris Dynamic

Reconfiguration (DR) software (see “About Hot-Pluggable and Hot-Swappable
Components” on page 127). In response to a component failure in an active path, the
multipathing software automatically switches to an alternate path, while the DR
feature lets you remove and replace the faulty component without impacting normal
system operations.

For Sun Fire V890 systems, two different types of multipathing software are
available:
■ Solaris IP Network Multipathing provides multipathing and load-balancing
capabilities for IP network interfaces.
■ Sun StorEdge Traffic Manager. See the Sun Fire V890 Server Product Notes for
details about this software.

Chapter 7 Server Administration 131

 For More Information
For information about setting up redundant hardware interfaces for storage devices
or networks, see:
■ “About Sun Fire V890 Mass Storage Features” on page 79
■ “About Redundant Network Interfaces” on page 91

For instructions on how to configure and administer Solaris IP Network

Multipathing, consult the IP Network Multipathing Administration Guide provided
with your specific Solaris release.

About Sun Management Center

Software
Sun Management Center software provides a single solution for managing multiple
Sun systems, devices, and network resources. With its intuitive Java technology-
based graphical interface, Sun Management Center offers powerful management
capabilities that let you:
■ Manage and monitor your server remotely from any location in the network
■ Display physical and logical views of your exact server configuration
■ Monitor system health conditions
■ Access real-time system performance and configuration data to diagnose potential
capacity problems and performance bottlenecks
■ Invoke SunVTS diagnostic software for online diagnosis of hardware problems
■ Use predictive failure analysis features to warn of potential memory and disk
hardware failures before they happen
■ Organize systems by geographical location, server function, administrative
responsibility, or other criteria for increased management flexibility
■ Implement enterprise-wide security measures, such as authentication, data
integrity, and access control lists

For More Information

Sun Management Center software is provided on the Software Supplement CD
supplied in the Solaris Media Kit for your release. For information about installing
and using Sun Management Center software, see the following documents provided
with the Sun Management Center software:

132 Sun Fire V890 Server Owner’s Guide • October 2005

■ Sun Management Center Software Installation Guide
■ Sun Management Center Software User’s Guide
■ Sun Management Center Software Supplement for Workgroup Servers

About Sun Remote System Control

Software
Sun Remote System Control (RSC) software is a remote server management tool that
lets you monitor and control supported Sun servers over serial lines or over a
network. RSC provides remote system administration for geographically distributed
or physically inaccessible systems and complements existing Sun monitoring and
diagnostics tools such as Sun Management Center, SunVTS, OpenBoot PROM, and
OpenBoot Diagnostics.

RSC software works with the system controller card included in all Sun Fire V890
servers. The system controller card runs independently of the host server, and
operates off of 5-volt standby power from the system’s power supplies. Together the
hardware and software allow RSC to serve as a “lights-out” management tool that
continues to function even when the server operating system goes offline or the
system is powered off.

The system controller card plugs in to a dedicated slot on the system I/O board and
provides the following ports through an opening in the system rear panel:
■ 10-Mbps Ethernet port via an RJ-45 twisted-pair Ethernet (TPE) connector
■ EIA-232D serial port via an RJ-45 connector

RSC Capabilities
Using RSC software, you can:
■ Access Solaris and OpenBoot PROM console functions remotely via the serial and
Ethernet ports on the system controller card
■ Run power-on self-test (POST) and OpenBoot Diagnostics from a remote console
■ Remotely monitor server environmental conditions, such as fan, temperature, and
power supply status, even when the server is offline
■ View a graphical representation of the server’s front panel, including keyswitch
position and LED states
■ Perform remote server reboot, power-on, and power-off functions on demand
■ Access a detailed log of RSC events, command history, and detected errors

Chapter 7 Server Administration 133

 RSC User Interfaces
RSC offers the following user interfaces:
■ A graphical user interface (GUI) that runs as a Java client application on
workstations connected to the server through an Ethernet interface or through a
standard serial connection
■ A command-line interface (CLI) that you can access through an Ethernet network
or through an alphanumeric terminal attached directly to the system controller
card’s serial port.

The Java technology-based GUI client application runs on workstations running the
Solaris, Microsoft Windows 98, or Windows NT operating systems.

For More Information

Sun RSC software is included on the Software Supplement CD for your specific
Solaris release. For installation instructions, see the Solaris Sun Hardware Platform
Guide provided in the Solaris Media Kit. For information about configuring and
using RSC, see the Sun Remote System Control (RSC) 2.2 User’s Guide, which is
included on the Sun Fire V890 Documentation CD.

About Volume Management Software

Sun Microsystems offers two different volume management applications for use on
Sun Fire V890 systems:
■ Solstice DiskSuite software
■ Sun StorEdge Traffic Manager

Volume management software lets you create disk volumes. Volumes are logical disk
devices comprising one or more physical disks or partitions from several different
disks. Once a volume is created, the operating system uses and maintains the
volume as if it were a single disk. By providing this logical volume management
layer, the software overcomes the restrictions imposed by physical disk devices.

Sun’s volume management products also provide RAID data redundancy and
performance features. RAID, which stands for redundant array of independent disks, is
a technology that helps protect against disk and hardware failures. Through RAID
technology, volume management software is able to provide high data availability,
excellent I/O performance, and simplified administration.

134 Sun Fire V890 Server Owner’s Guide • October 2005

Sun’s volume management applications offer the following features:
■ Support for several types of RAID configurations, which provide varying degrees
of availability, capacity, and performance
■ Hot-spare facilities, which provide for automatic data recovery when disks fail
■ Performance analysis tools, which let you monitor I/O performance and isolate
bottlenecks
■ A graphical user interface, which simplifies storage management
■ Support for online resizing, which enables volumes and their file systems to grow
and shrink online
■ Online reconfiguration facilities, which let you change to a different RAID
configuration or modify characteristics of an existing configuration

Multipathing Software
Sun StorEdge Traffic Manager software for Solaris OS, which is part of the Sun SAN
Foundation Suite, automates multipath I/O failover, failback, and SAN-wide load
balancing. For more information about this product, see the Sun Fire V890 Server
Product Notes.

RAID Concepts
Solstice DiskSuite software supports RAID technology to optimize performance,
availability, and user cost. RAID technology improves performance, reduces
recovery time in the event of file system errors, and increases data availability even
in the event of a disk failure. There are several levels of RAID configurations that
provide varying degrees of data availability with corresponding trade-offs in
performance and cost.

This section describes some of the most popular and useful of those configurations,
including:
■ Disk concatenation
■ Disk mirroring (RAID 1)
■ Disk striping (RAID 0)
■ Disk striping with parity (RAID 5)
■ Hot spares

Chapter 7 Server Administration 135

 Disk Concatenation
Disk concatenation is a method for increasing logical volume size beyond the
capacity of one disk drive by creating one large volume from two or more smaller
drives. This lets you create arbitrarily large partitions.

Using this method, the concatenated disks are filled with data sequentially, with the
second disk being written to when no space remains on the first, the third when no
room remains on the second, and so on.

RAID 1: Disk Mirroring

Disk mirroring (RAID 1) is a technique that uses data redundancy—two complete
copies of all data stored on two separate disks—to protect against loss of data due to
disk failure. One logical volume is duplicated on two separate disks.

Whenever the operating system needs to write to a mirrored volume, both disks are
updated. The disks are maintained at all times with exactly the same information.
When the operating system needs to read from the mirrored volume, it reads from
whichever disk is more readily accessible at the moment, which can result in
enhanced performance for read operations.

RAID 1 offers the highest level of data protection, but storage costs are high, and
write performance is reduced since all data must be stored twice.

136 Sun Fire V890 Server Owner’s Guide • October 2005

RAID 0: Disk Striping
Disk striping (RAID 0) is a technique for increasing system throughput by using
several disk drives in parallel. Whereas in non-striped disks the operating system
writes a single block to a single disk, in a striped arrangement, each block is divided
and portions of the data are written to different disks simultaneously.

System performance using RAID 0 will be better than using RAID 1 or 5, but the
possibility of data loss is greater because there is no way to retrieve or reconstruct
data stored on a failed disk drive.

RAID 5: Disk Striping With Parity

RAID 5 is an implementation of disk striping in which parity information is
included with each disk write. The advantage of this technique is that if any one
disk in a RAID 5 array fails, all the information on the failed drive can be
reconstructed from the data and parity on the remaining disks.

System performance using RAID 5 will fall between that of RAID 0 and RAID 1;
however, RAID 5 provides limited data redundancy. If more than one disk fails, all
data is lost.

Hot Spares (Hot Relocation)

In a hot spares arrangement, one or more disk drives are installed in the system but
are unused during normal operation. Should one of the active drives fail, the data on
the failed disk is automatically reconstructed and generated on a hot spare disk,
enabling the entire data set to maintain its availability.

For more information, see the documentation supplied with Solstice DiskSuite
software.

Chapter 7 Server Administration 137

 About the Solaris luxadm Utility
The luxadm program is a command-line management utility for administering the
Sun Fire V890 internal Fibre Channel-Arbitrated Loop (FC-AL) storage subsystem
and supported external storage arrays. You use luxadm to perform physical disk
management tasks, including disk hot-plug operations. The luxadm utility is
installed automatically when you install the Solaris OS.

The luxadm utility performs a variety of control and query tasks through a number
of subcommands and command-line options. Using luxadm, you can:
■ Assign a convenient enclosure name to the Sun Fire V890 internal storage array
■ Display the physical and logical device paths, world wide names (WWNs), and
enclosure names for storage arrays and individual disks
■ Display configuration, environmental, and status information for any array or
individual disk
■ Reserve a specific disk for exclusive use by a single host
■ Perform hot-plug insertion or removal of disks
■ Download firmware and fcode updates for mass storage components

Note – Setting the front panel keyswitch to the Locked position prevents
reprogramming of system firmware. If the keyswitch is turned to the Locked
position after a firmware update operation has started, the operation is allowed to
proceed to completion. For more information about the front panel keyswitch, see
“About the Status and Control Panel” on page 11.

For More Information

Platform Notes: Using luxadm Software provides information about the luxadm utility,
including descriptions of hot-plug procedures for Sun Fire V890 internal disk drives.
This document is available on the Sun Fire V890 Documentation CD. Refer also to
the luxadm(1M) man page, and for late-breaking information, to the Sun Fire V890
Server Product Notes.

138 Sun Fire V890 Server Owner’s Guide • October 2005

About Sun Cluster Software
Sun Cluster software lets you connect multiple Sun servers in a cluster
configuration. A cluster is a group of nodes that are interconnected to work as a
single, highly available and scalable system. A node is a single instance of Solaris
software—it may be running on a standalone server or on a domain within a
standalone server. With Sun Cluster software, you can add or remove nodes while
online, and mix and match servers to meet your specific needs.

Sun Cluster software delivers high availability through automatic fault detection
and recovery, and scalability, ensuring that mission-critical applications and services
are always available when needed.

With Sun Cluster software installed, other nodes in the cluster will automatically
take over and assume the workload when a node goes down. It delivers
predictability and fast recovery capabilities through features such as local
application restart, individual application failover, and local network adapter
failover. Sun Cluster software significantly reduces downtime and increases
productivity by helping ensure continuous service to all users.

The software lets you run both standard and parallel applications on the same
cluster. It supports the dynamic addition or removal of nodes, and enables Sun
servers and storage products to be clustered together in a variety of configurations.
Existing resources are used more efficiently, resulting in additional cost savings.

Sun Cluster software allows nodes to be separated by up to 10 kilometers. This way,

in the event of a disaster in one location, all mission-critical data and services remain
available from the other unaffected locations.

For more information, see the documentation supplied with the Sun Cluster
software.

Chapter 7 Server Administration 139

140 Sun Fire V890 Server Owner’s Guide • October 2005
CHAPTER 7

LED Status Indicators

This chapter provides information about the system’s interior and rear panel LED
status indicators. Topics covered in this chapter include:
■ “About CPU/Memory Slot LEDs” on page 118
■ “About PCI Slot LEDs” on page 119
■ “About Power Supply LEDs” on page 121
■ “About Fan Tray LEDs” on page 122
■ “About Disk Drive LEDs” on page 123
■ “About Gigabit Ethernet LEDs” on page 125

For a description of the system’s front panel LED indicators, see “About the Status
and Control Panel” on page 11.

117
 About CPU/Memory Slot LEDs
The CPU/Memory slot LEDs are located on the horizontal panel between
CPU/Memory slots B and C and are visible when the right side door is open. There
are two LEDs for each CPU/Memory slot, as shown below.

Icon Name LED Function

Power On Lights when the slot is receiving power.

Fault Reserved for future use.

118 Sun Fire V890 Server Owner’s Guide • October 2005

About PCI Slot LEDs
The PCI slot LEDs are located on the vertical bracket on the right side of the PCI
slots and are visible when the left side door is open. There are three LEDs for each
PCI slot, as shown below.

Icon Name LED Function

Power On Lights when the slot is receiving power.

Fault Blinks while the card is being tested, when a hot-plug

operation is in progress, or when the card is powered on but
logically detached from the operating system.

Stays lit if the card encounters a fault.

OK-to-Remove Lights when it is safe to remove the card.

Chapter 7 LED Status Indicators 119

 The following table shows how to interpret the various possible LED patterns.

Interpretation

Off Off Off The slot power is off. A PCI card can be safely inserted to
start a hot-plug operation.
On Blinking Off The installed card is being tested, configured, or
deconfigured, or the card is powered on but logically
detached from the operating system.
On Off Off The slot power is on and the PCI card is operating
normally.
Off On On The PCI card has encountered a fault. The card can be
safely removed.
Off Off On The card can be safely removed.

Note – If the slot is empty and the Fault or OK-to-Remove LED is on, pressing the
contact push button for the slot will clear the LED.

For more information about PCI cards and hot-plug operations, see:
■ “About PCI Cards and Buses” on page 56
■ “About Hot-Pluggable and Hot-Swappable Components” on page 127

120 Sun Fire V890 Server Owner’s Guide • October 2005

About Power Supply LEDs
There are three LEDs located on the rear of each power supply, as shown below.

Icon Name LED Function

Fault Lights when the power supply encounters a fault.

AC-Present Lights when AC power input is present and within acceptable

Status operating limits.

DC Status Lights when all DC outputs are functional and within

acceptable operating limits.

Chapter 7 LED Status Indicators 121

 About Fan Tray LEDs
The Thermal Fault LED on the system status and control panel indicates the overall
status of the cooling system. The Thermal Fault LED lights when a fan fault or
overtemperature condition is detected. LEDs inside the system indicate the fault
status of each fan tray assembly.

The fan tray LEDs are located beside or beneath each fan tray assembly. There are
three LEDs per fan tray, as shown below.

122 Sun Fire V890 Server Owner’s Guide • October 2005

Icon Name LED Function

Power On Lights when the fan tray is receiving power.

Fault Lights when the fan tray encounters a fault.

OK-to-Remove Lights when it is safe to remove the fan tray assembly from a
powered-on system (only when redundant fan trays are present).

The following table shows how to interpret the various possible LED patterns.

Interpretation

Off Off Off The fan tray is not receiving power or is improperly
inserted.
On Off Off The fan tray is receiving power and operating normally.
Off On On The fan tray has encountered a fault and can be safely
removed from a powered-on system.

For more information about fan trays and hot-plug operations, see:
■ “About Fan Trays” on page 64
■ “About Hot-Pluggable and Hot-Swappable Components” on page 127

About Disk Drive LEDs

The Disk Fault LED on the system status and control panel indicates the general
status of the disk subsystem. The Disk Fault LED lights when a fault is detected in
the disk subsystem. LEDs inside the system indicate the fault status of individual
disk drives.

There are three LEDs for each disk drive. The disk drive LEDs are located on the
front of the disk cage, as shown below.

Chapter 7 LED Status Indicators 123

 Icon Name LED Function

Activity Blinks slowly while the disk drive is being tested, configured,
or deconfigured during a hot-plug operation.

Blinks rapidly as the disk drive spins up or spins down.

Stays lit when the disk drive is at speed and operating

normally but experiencing no read or write activity. Blinks
rapidly and irregularly in response to disk read or write
activity.
Fault Lights when the disk drive encounters a fault.

OK-to-Remove Lights when it is safe to remove the disk drive during a hot-plug
operation.

Blinks (under software control) to direct attention to a disk drive.

124 Sun Fire V890 Server Owner’s Guide • October 2005

The following table shows how to interpret the various possible LED patterns.

Interpretation

Off Off Off Slot power is off. A disk drive can be safely inserted
as part of a hot-plug operation.
Rapid Off Off Disk drive is spinning up or down.
Blinking
Slow Off Off Disk drive is being configured or deconfigured
Blinking during a hot-plug operation.
On Off Off Disk drive is up to speed and operating normally.
Irregular Off Off Disk drive is experiencing read or write activity.
Blinking
On On Off Disk drive has encountered a fault.
Off Off On Disk drive can be safely removed as part of a
hot-plug operation.

For more information about disk drives and hot-plug operations, see:
■ “About Internal Disk Drives” on page 84
■ “About Hot-Pluggable and Hot-Swappable Components” on page 127

About Gigabit Ethernet LEDs

Four LEDs provide status information for the Gigabit Ethernet port. The LEDs are
located above the Gigabit Ethernet port on the system rear panel, as shown below.

Chapter 7 LED Status Indicators 125

 Label Name LED Function

RX Receive Activity Indicates data activity on the receive channel.

TX Transmit Activity Indicates data activity on the transmit channel.

FDX Full Duplex Indicates that the Gigabit Ethernet interface is

operating in full-duplex mode.

Link Link Present Indicates that a link is established with a link

partner.

126 Sun Fire V890 Server Owner’s Guide • October 2005

CHAPTER 9

Using Removable Media Storage

Devices

This chapter contains basic information about how to use removable media storage
devices.

The following tasks are covered in this chapter:

■ “How to Insert a CD or DVD Into the Drive” on page 162
■ “How to Eject a CD or DVD With Software Commands” on page 164
■ “How to Eject a CD or DVD Manually” on page 165
■ “How to Eject a CD or DVD in an Emergency” on page 167
■ “How to Clean a CD or DVD” on page 168
■ “How to Insert a Tape Cartridge” on page 171
■ “How to Remove a Tape Cartridge” on page 172
■ “How to Control a Tape Drive” on page 173
■ “How to Clean a Tape Drive” on page 173

Other information covered in this chapter includes:

■ “About the DVD-ROM Drive” on page 162
■ “About Tape Drives and Tape Cartridges” on page 170

The Sun Fire V890 server provides front-panel access to three mounting bays. One
bay houses an IDE DVD-ROM drive, which is standard in all system configurations.

The other two bays accommodate an optional wide (68-pin) SCSI removable device,
which must be ordered separately. The tape drive option also requires a SCSI cable
(Sun part number X912A) and a SCSI adapter card (Sun part number X6758A); both
must be ordered separately.

You can easily convert the two SCSI device bays into a single full-height bay by
removing the metal shelf divider.

161
 About the DVD-ROM Drive
The digital versatile disc-read only memory (DVD-ROM) drive in your system ships
with a specification sheet that contains the following information:
■ Type of DVD-ROM discs that you can use with the drive
■ Handling and storage information
■ Physical characteristics
■ Power requirements
■ Cleaning instructions
■ Description of DVD-ROM drive controls, indicators, and jumper settings

How to Insert a CD or DVD Into the

Drive

What to Do
1. Push the Eject button on the DVD-ROM drive to release the drive tray.

2. Place a CD or DVD into the drive tray, label side up.

A disc is a single-sided or double-sided storage medium. Place it into the tray
with the appropriate label side up, as shown.

162 Sun Fire V890 Server Owner’s Guide • October 2005

3. Gently push the tray back into the drive.
The drive has an automated closing mechanism that retracts the tray into the drive.

What Next
You can eject a CD or DVD from the drive by using one of three methods:
■ With software commands; see “How to Eject a CD or DVD With Software
Commands” on page 164
■ Manually; see “How to Eject a CD or DVD Manually” on page 165
■ Using an emergency procedure; see “How to Eject a CD or DVD in an
Emergency” on page 167

Chapter 9 Using Removable Media Storage Devices 163

 How to Eject a CD or DVD With Software
Commands

Before You Begin

If the server is set up without a system console, you need to set up one in order to
issue software commands; see:
■ “About Setting Up a Console” on page 30

What to Do
1. From the system console device, change directories to a directory that is not in the
/cdrom hierarchy.

2. Type the following command to eject the CD or DVD:

% eject cdrom

The disc should eject.

3. If the disc does not eject, kill any processes accessing the DVD-ROM drive and
repeat Step 2.
The disc will not eject while the drive is in use. To kill any processes accessing the
DVD-ROM drive, become superuser and type the following:

% su
Password:
# fuser -k /cdrom/cdrom0

Note – You should warn users before abruptly halting processes. The command
fuser -u /cdrom/cdrom0 helps identify who is accessing the DVD-ROM drive.
Refer to the Solaris System Administrator’s Guide for more information about the
fuser command.

164 Sun Fire V890 Server Owner’s Guide • October 2005

 What Next
You can also eject a disc by using one of these methods:
■ Manually; see “How to Eject a CD or DVD Manually” on page 165
■ Using an emergency procedure; see “How to Eject a CD or DVD in an
Emergency” on page 167

How to Eject a CD or DVD Manually

Before You Begin

If the server is set up without a system console, you need to set up one in order to
issue software commands; see:
■ “About Setting Up a Console” on page 30

What to Do
1. From the system console device, change directories to a directory that is not in the
/cdrom hierarchy.

2. Press the Eject button on the front panel.

The drive should eject the tray so that you can remove the disc.

Chapter 9 Using Removable Media Storage Devices 165

 3. If the disc does not eject, kill any processes accessing the DVD-ROM drive and
repeat Step 2.
The disc will not eject while the drive is in use. To kill any processes accessing the
DVD-ROM drive, become superuser and type the following:

% su
Password:
# fuser -k /cdrom/cdrom0

Note – You should warn users before abruptly halting processes. The command
fuser -u /cdrom/cdrom0 helps identify who is accessing the DVD-ROM drive.
Refer to the Solaris System Administrator’s Guide for more information about the
fuser command.

What Next
You can also eject a disc by using one of these methods:

166 Sun Fire V890 Server Owner’s Guide • October 2005

 ■ With software commands; see “How to Eject a CD or DVD With Software
Commands” on page 164
■ Using an emergency procedure; see “How to Eject a CD or DVD in an
Emergency” on page 167

How to Eject a CD or DVD in an

Emergency

Before You Begin

Use the emergency ejection procedure only in emergency situations; for instance, if you
unmount the disc and the Eject button does not function.

What to Do

Caution – If this procedure is used while a disc is mounted, you can degrade or
destroy data in your system.

1. Turn off the power to your system.

See “How to Power Off the System” on page 38.

2. Unfold and straighten one end of a large wire paper clip.

3. Insert the straightened end of the clip into the emergency eject hole and
press firmly.

4. Pull the tray from the drive after the clip is inserted into the hole.

Chapter 9 Using Removable Media Storage Devices 167

 What Next
You can also eject a disc by using one of these methods:
■ With software commands; see “How to Eject a CD or DVD With Software
Commands” on page 164
■ Manually; see “How to Eject a CD or DVD Manually” on page 165

How to Clean a CD or DVD

Before You Begin

Eject the CD or DVD and remove it from the tray; see:
■ “How to Eject a CD or DVD With Software Commands” on page 164

168 Sun Fire V890 Server Owner’s Guide • October 2005

 Note – If the drive cannot read a disc, you may have a dusty or dirty disc.

What to Do
1. Clean the disc with compressed air.
Compressed air can remove most accumulations of dust and large dirt particles. If
you have access to the drive’s read head, verify that it is also dust free.

2. If spraying with compressed air fails to remove the dirt on a disc, wipe the disc
using a soft, clean, lint-free, dry cloth.
■ Wipe the data areas of the disc (on both sides if necessary) radially from the center
to the outside.
■ Do not wipe in a circular motion.
■ Wipe only the affected areas of the disc.

The figure below shows the correct and incorrect way to clean a CD or DVD.

Data area of disc

Correct Incorrect

What Next
To insert a CD or DVD into the drive, see:
■ “How to Insert a CD or DVD Into the Drive” on page 162.

Chapter 9 Using Removable Media Storage Devices 169

 About Tape Drives and Tape Cartridges
There are a number of different tape drives offered by Sun Microsystems for your
system. Each tape drive is shipped with a specification sheet that contains the
following information:
■ Type of cartridges that can be used with the drive
■ Cartridge storage capacity
■ Handling and storage information
■ Physical characteristics
■ Power requirements
■ Cleaning instructions
■ Description of controls, indicators, and jumper settings

Handling and Storing Tape Cartridges

The following general handling and storage information applies to cartridges
for any of the tape drives offered for your system:
■ Keep cartridges away from anything magnetic.
■ Store cartridges in a dust-free environment.
■ Keep cartridges away from direct sunlight and sources of heat, cold, or humidity.
Constant room temperature and 50 percent humidity is recommended.
■ Do not touch the surface of the tape.

Thermal Conditioning
To ensure proper thermal conditioning, keep the tape cartridge at the same
temperature as the drive for 24 hours. This applies to cartridges for any of the tape
drives offered for your system.

170 Sun Fire V890 Server Owner’s Guide • October 2005

 How to Insert a Tape Cartridge

What to Do
1. Verify that the tape cartridge write-protect switch is set correctly.
If the lock window is open, the tape is write-protected.

Write-protect switch

2. Insert the cartridge into the drive, label side up.

3. Push gently on the cartridge until it is pulled into the drive.

What Next
To remove a tape cartridge from the drive, see:
■ “How to Remove a Tape Cartridge” on page 172

Chapter 9 Using Removable Media Storage Devices 171

 How to Remove a Tape Cartridge

Before You Begin

The information in this section applies to a DDS-3 tape drive. If you have a different
type of tape drive installed, see the specifications shipped with the drive for
information.

What to Do
1. Check that there is no drive activity.
The green activity LED should be unlit. A flashing LED indicates drive activity.

Caution – Do not eject the tape cartridge when the drive is active, or you may incur
data loss or equipment damage.

Activity LED Attention LED Eject button

2. Push the Eject button and remove the tape cartridge.

What Next
To insert a tape cartridge into the drive, see:
■ “How to Insert a Tape Cartridge” on page 171

172 Sun Fire V890 Server Owner’s Guide • October 2005

 How to Control a Tape Drive

What to Do
For information about software commands needed to read and write data with your
tape drive, refer to the Solaris Handbook for Sun Peripherals or the Solaris User’s Guide.

How to Clean a Tape Drive

Before You Begin

Observe these rules about when to clean a tape drive:

1. Clean the drive after the first four hours of use with a new tape.

2. After that, clean the tape drive after every 25 hours of use to maintain reliable
operation.

3. Clean the drive twice as often if you use it in a dusty environment or operate
it infrequently.

What to Do
● Insert a cleaning cartridge into the drive.
The tape should play for a short while, and then eject automatically.

Chapter 9 Using Removable Media Storage Devices 173

 Do not use any cartridge other than a DDS-approved cleaning tape cartridge to clean
your tape drive.

174 Sun Fire V890 Server Owner’s Guide • October 2005

APPENDIX A

Connector Pinouts

This appendix gives you reference information about the system’s rear panel ports
and pin assignments. Topics covered in this appendix include:
■ “Reference for the Serial Port A and B Connectors” on page 176
■ “Reference for the USB Connectors” on page 177
■ “Reference for the Twisted-Pair Ethernet Connector” on page 178
■ “Reference for the System Controller Ethernet Connector” on page 179
■ “Reference for the System Controller Serial Connector” on page 180

175
 Reference for the Serial Port A and B
Connectors
The serial port conforms to EIA-423 and EIA-232D specifications.

Serial Port Connector Diagram

13 1
25 14

Serial Port Signals

Signal descriptions ending in “A” indicate that the signal is associated with the port
provided by a standard DB-25 serial cable or the connector labeled “A” on the
optional DB-25 splitter cable. Signal descriptions ending in “B” indicate that the
signal is associated with the port provided by the connector labeled “B” on the
optional DB-25 splitter cable.

Pin Signal Description Pin Signal Description

1 No Connection 14 Transmit Data B

2 Transmit Data A 15 Transmit Clock A (External)
3 Receive Data A 16 Receive Data B
4 Ready To Send A 17 Receive Clock A
5 Clear To Send A 18 Receive Clock B
6 Synchronous A 19 Ready To Send B
7 Signal Ground A 20 Data Terminal Ready A
8 Data Carrier Detect A 21 No Connection
9 No Connection 22 No Connection
10 No Connection 23 No Connection
11 Data Terminal Ready B 24 Transmit Clock A (Internal)
12 Data Carrier Detect B 25 Transmit Clock B

176 Sun Fire V890 Server Owner’s Guide • October 2005

Pin Signal Description Pin Signal Description

13 Clear To Send B

Reference for the USB Connectors

Two Universal Serial Bus (USB) connectors are located on the system I/O board and
can be accessed from the rear panel.

USB Connector Diagram

A1 B1

A2 B2

A3 B3

A4 B4

USB Connector Signals

Pin Signal Description Pin Signal Description

A1 +5 VDC B1 +5 VDC
A2 Port Data_N B2 Port Data_N
A3 Port Data_P B3 Port Data_P
A4 Ground B4 Ground

Appendix A Connector Pinouts 177

 Reference for the Twisted-Pair Ethernet
Connector
The twisted-pair Ethernet (TPE) connector is an RJ-45 connector located on the
system I/O board and can be accessed from the rear panel.

TPE Connector Diagram

TPE Connector Signals

Pin Signal Description Pin Signal Description

1 Transmit Data + 5 Common Mode Termination

2 Transmit Data - 6 Receive Data -
3 Receive Data + 7 Common Mode Termination
4 Common Mode Termination 8 Common Mode Termination

178 Sun Fire V890 Server Owner’s Guide • October 2005

Reference for the System Controller
Ethernet Connector
The system controller Ethernet connector is an RJ-45 connector located on the system
controller board and can be accessed from the rear panel.

System Controller Ethernet Connector Diagram

8 1

System Controller Ethernet Connector Signals

Pin Signal Description Pin Signal Description

1 Transmit Data + 5 Common Mode Termination

2 Transmit Data - 6 Receive Data -
3 Receive Data + 7 Common Mode Termination
4 Common Mode Termination 8 Common Mode Termination

Appendix A Connector Pinouts 179

 Reference for the System Controller
Serial Connector
The system controller serial connector is an RJ-45 connector located on the system
controller card and can be accessed from the rear panel.

System Controller Serial Connector Diagram

SERIAL

8 1

System Controller Serial Connector Signals

Pin Signal Description Pin Signal Description

1 Ready To Send 5 Ground

2 Data Terminal Ready 6 Receive Data
3 Transmit Data 7 No Connection
4 Ground 8 Clear To Send

180 Sun Fire V890 Server Owner’s Guide • October 2005

APPENDIX B

System Specifications

This appendix provides the following specifications for the Sun Fire V890 server:
■ “Reference for Physical Specifications” on page 182
■ “Reference for Electrical Specifications” on page 182
■ “Reference for Environmental Requirements” on page 183
■ “Reference for Agency Compliance Specifications” on page 184
■ “Reference for Clearance and Service Access Specifications” on page 185

181
 Reference for Physical Specifications
The dimensions and weight of the system are as follows.

Measurement U.S. Metric Comments

Height (with casters) 28.1 in 71.4 cm

Width 18.9 in 48.0 cm
Depth 32.9 in 83.6 cm
Weight:
Minimum 194.0 lb 88.0 kg Actual weight depends on the
Maximum 288.0 lb 130.6 kg installed options
Power Cord 8.2 ft 2.5 m

Reference for Electrical Specifications

The following table provides the electrical specifications for the system.

Parameter Value

Input
Nominal Frequencies 50 Hz or 60 Hz nominal
Nominal Voltage Range Autoranging 200 to 240 VAC
Maximum Current AC RMS 8 A @ 200 VAC (each power cord for two
power supplies per system)
AC Operating Range 180 to 264 Vrms, 47 - 63Hz
Output
+3.3 VDC 3 to 72 A
+5 VDC 3 to 56 A
+12 VDC 1 to 35 A
+48 VDC 0 to 50 A
Maximum DC Power Output 2509 Watts
Maximum System AC Power Consumption 3200 Watts
Maximum System Heat Dissipation 10,912 BTU/hr
Volt-Ampere Rating 2078 VA with 1629 Watt load (PF=0.98)

182 Sun Fire V890 Server Owner’s Guide • October 2005

Reference for Environmental
Requirements
The operating and non-operating environmental requirements for the system are
as follows.

Parameter Value

Operating
Temperature 5˚C to 35˚C (41˚F to 95˚F)—IEC 68-2-1, 68-2-2
Humidity 20% to 80% RH, noncondensing; 27 ˚C max wet bulb—IEC 68-2-2,
68-2-3
Altitude 0 to 3000 meters (0 to 10,000 feet)—IEC 68-2-40, 68-2-41
Vibration:
Deskside 0.0002 g2/Hz, 5 to 500 Hz (random)—IEC 68-2-6
Rackmounted 0.00015 g2/Hz, 5 to 500 Hz (random)—IEC 68-2-6
Shock:
Deskside 4 g peak, 11 milliseconds half-sine pulse—IEC 68-2-27
Rackmounted 3 g peak, 11 milliseconds half-sine pulse—IEC 68-2-27
Declared Acoustics 6.7 bels dB(A) operating, 7.6 bels dB(A) at ok prompt
Non-Operating
Temperature -20˚C to 60˚C (-4˚F to 140˚F)—IEC 68-2-1, 68-2-2
Humidity 95% RH, noncondensing at 40˚C—IEC 68-2-2, 68-2-3
Altitude 0 to 12,000 meters (0 to 40,000 feet)—IEC 68-2-40, 68-2-41
Vibration:
Deskside 0.002 g2/Hz, 5 to 500 Hz (random)—IEC 68-2-6
Rackmounted 0.0015 g2/Hz, 5 to 500 Hz (random)—IEC 68-2-6
Shock:
Deskside 15 g peak, 11 milliseconds half-sine pulse—IEC 68-2-27e
Rackmounted 10 g peak, 11 milliseconds half-sine pulse—IEC 68-2-27e
Handling Drops 50 mm—IEC 68-2-31
Threshold Impact 1 m/s—SUN 900-1813

Appendix B System Specifications 183

 Reference for Agency Compliance
Specifications
The system complies with the following specifications.

Category Relevant Standards

Safety EN60950/IEC60950 TUV

UL 60950, CB Scheme IEC 60950, C22.2 No. 60950 from UL
RFI/EMI Australia/New Zealand AS/NZ 3548 Class A
Industry Canada ICES-003 Class A
European Community EN55022 Class A
Japan VCCI Class A
Taiwan CNS 13438 Class A
US FCC 47CFR15.B Class A
Immunity EN55024
EN61000-4-2
EN61000-4-3
EN61000-4-4
EN61000-4-5
EN61000-4-6
EN61000-4-8
EN61000-4-11
X-ray US DHHS 21CFR Subchapter J
PTB German X-ray Decree

184 Sun Fire V890 Server Owner’s Guide • October 2005

Reference for Clearance and Service
Access Specifications
Minimum clearances needed for proper cooling are as follows.

Blockage Required Clearance

Front blockage only 3.0 in (7.6 cm)

Rear blockage only 3.5 in (8.9 cm)
Front and rear blockage
Front clearance 3.5 in (8.9 cm)
Rear clearance 4.0 in (10.2 cm)

Minimum clearances needed for servicing the system are as follows.

Area Required Clearance

Front
Deskside system 36 in (91 cm)
Rackmounted system 48 in (122 cm)
Rear 36 in (91 cm)
Right 36 in (91 cm)
Left 36 in (91 cm)

Appendix B System Specifications 185

186 Sun Fire V890 Server Owner’s Guide • October 2005
 Index

A boot-device configuration variable, 111

AC power cord booting
connecting, 25 after installing new hardware, 40
when to disconnect, 26 boxes shipped to you, 23
agency compliance specifications, 184 Break key
air baffle, CPU, 50 disabling, 14
AL_PAs, 88
alphanumeric terminal, 4, 31 C
attaching, 31 cables
settings for, 31 Gigabit Ethernet, 98
ASCII terminal, See alphanumeric terminal keyboard/mouse, 35
serial port splitter cable, 31
.asr command, 113, 116 to 119
twisted-pair Ethernet (TPE), 99
asr-disable command, 113, 116 to 119
CD, See compact disc (CD)
asr-enable command, 113, 117
cfgadm command, 130
auto-boot? configuration variable, 43, 45, 110 to
chassis ground screw, 10
113
checklist of parts, 23
auto-boot-on-error? configuration
variable, 110 to 114 chip multithreading processor, 48
automatic failover, 90 clearance specifications, 185
automatic system recovery (ASR) cluster configurations, 139
deconfiguring devices manually, 116 compact disc
disabling, 114 cleaning, 169
enabling, 110 ejecting in an emergency, 167
obtaining status information, 119 ejecting manually, 165
overview, 19 ejecting with software commands, 164
reconfiguring devices manually, 116, 117 inserting into drive, 162
when drive cannot read, 169
B compact PCI (cPCI) cards, 58
backplane, See FC-AL disk backplane concatenation of disks, 136
baud rate, 32, 67 configuration, See hardware configuration
boot device, how to select, 101 console, See system console

187
Control-C, keyboard combination, 105 access door, 8
conventions used in this book, xxxiv configuration guidelines, 84, 86
correctable ECC error, 21 dual-ported, 20, 79, 84
hot-plug, 3, 16, 79, 85, 127 to 130, 138
CPU fan tray, See fan tray assemblies
LEDs, 7, 12, 85, 156
CPU/Memory board, 2, 48, 50
locating drive bays, 7, 85
air baffle, 50
documentation
configuration guidelines, 48, 50
related, xxxvi
CPU numbering, 49
slot status LEDs, 142 door lock, 8
UltraSPARC IV, 48 dual inline memory module (DIMM),See memory
modules
D dual-loop FC-AL configuration, 3, 20, 79, 84, 86
damage, preventing DVD, See digital versatile disc (DVD)
electrostatic, 54 DVD-ROM drive, 162 to 169
to tape cartridges, 170 location, 7
devalias command, 116 to 117 specifications, 162
device trees, rebuilding, 41 Dynamic Multipathing (DMP), 80
diag-console command, 43, 45 Dynamic Reconfiguration (DR), 129
diagnostic testing, 5, 22, 119
diag-switch? configuration variable, 112 to 113, E
122 EIA-232D serial communication, 27
diag-trigger configuration variable, 112, ?? to EIA-232D serial communications, 67, 70
113 EIA-423 serial communication, 27
digital versatile disc EIA-423 serial communications, 67, 70
cleaning, 169 eject cd command, 164, 166
ejecting in an emergency, 167 ejecting a CD or DVD, 164 to 166
ejecting manually, 165 electrical specifications, 182
ejecting with software commands, 164
emergency eject (of a CD or DVD), 167
inserting into drive, 162
when drive cannot read, 169 emergency shutdown, 13, 14
dimensions, See specifications .env command, 105, 108, 109
DIMM, See memory modules environmental monitoring subsystem
See also OpenBoot environmental monitor
disc, compact, See compact disc
and hot-swap events, 128
disc, digital versatile, See digital versatile disc and RSC, 5, 59
disk backplane, See FC-AL disk backplane automatic thermal shutdown, 18, 50, 66, 105
disk configuration error messages, 18, 105, 128
concatenation, 136 monitoring for fan faults, 18, 65, 104, 105, 128
configuration guidelines, 84, 86 monitoring for power faults, 18, 104, 128
hot spares, 21, 137 temperature monitoring, 18, 104, 105
hot-plug, 16, 85, 127 to 130, 138 environmental specifications, 183
mirroring, 21, 135 env-off command, 104, 107
RAID 0, 21, 80, 137
env-on command, 41, 104, 106
RAID 1, 21, 136
RAID 5, 21, 80, 137 eri Fast Ethernet driver, 90, 97
striping, 21, 80, 137 error correcting code (ECC), 21
disk drive, 3, 84, 85 error messages

188 Sun Fire V890 Server Owner’s Guide • October 2005

 correctable ECC error, 21 configuration guidelines, 86, 87
fan-related, 18, 128 Fibre Channel-Arbitrated Loop, See FC-AL
log file, 18 filler panel
power-related, 18, 19, 128 CPU air baffle, 50
temperature-related, 18 CPU fan tray, 66
/etc/hostname file, 95 firmware updates, 72, 138
/etc/hosts file, 96 flash PROM
Ethernet, 4, 89 jumpers, 72
adding an interface, 94 programming, 72
cable requirements, 98, 99 disabling, 14, 74, 138
configuring interface, 27, 89 frame buffer card, 4, 30
drivers, 90, 97 front panel features, 7
link integrity test, 93, 97
fuser command, 164, 166
redundant network interfaces, 91
See also Fast Ethernet port
twisted-pair cable, attaching, 99 G
using multiple interfaces, 4, 90, 91 ge Gigabit Ethernet driver, 90, 97
Gigabit Ethernet port Gigabit Ethernet port, 4, 90
external storage, 3, 87 cabling requirements, 98
LEDs, 159
location, 9
F
grounding screw, 9, 10
failover capability, 3, 4, 5, 16, 17, 79, 90, 91
fan tray assemblies
configuration guidelines, 64 to 66
H
CPU fan tray filler panel, 66 hardware configuration, 47
hot-swap capability, 17, 65, 127 to 130 CPU/Memory boards, 48, 50
LEDs, 66, 152 disk drives, 84, 86
redundancy, 17 fan tray assemblies, 64 to 66
See also fans FC-AL disk backplanes, 82, 83
FC-AL host adapters, 86, 87
fans
hardware jumpers, 69 to ??
See also fan tray assemblies
FC-AL disk backplane, 74
fault monitoring and reporting, 17, 18, 65, 128
flash PROM, 72
Fast Ethernet port, 4, 90 serial ports, 70
attaching twisted-pair cable, 99 memory, 51 to ??
location, 9 PCI cards, 56 to 58
fault indicators, See status LEDs power supplies, 61, 63
FC-AL removable media devices, 67
administration, 138 SCSI devices, 67
arbitrated loop physical address (AL_PA), 88 serial ports, 67
technology overview, 77, 78 system controller card, 59
FC-AL disk backplane, 3, 79, 84 USB ports, 68
configuration guidelines, 82, 83 hardware jumpers, See jumpers
dual-loop configuration, 3, 20, 79, 83, 84, 86 hardware redundancy, 3, 4, 5, 16, 17, 58, 79, 90, 91
full and split configurations, 83 hardware watchdog, enabling, 19
jumpers, 74
host name, 92, 94
FC-AL disk drive, See disk drive
hot spares, See disk configuration
FC-AL host adapter, 3, 20, 79, 84, 86, 87

Index 189
hot-plug feature Normal position, 14, 36, 74
definition, 127 settings, 14
disk drives, 3, 16, 79, 84, 127 to 130, 138
OK-to-Remove LED, 12, 146, 155, 157 L
PCI cards, 2, 16, 56, 58, 127 to 130 LEDs, See status LEDs
user interfaces, 130, 138 link integrity test, 93, 97
hot-swap feature log files
definition, 127 error, 18
fan tray assemblies, 17, 127 to 130 RSC, 20
power supplies, 17, 127 to 130
luxadm utility, 129, 138
I M
I/O board, 20, 60, 70 to 74, 81, 90, 130, 133
memory modules, 2, 51
jumpers, 68, 70
banks of, 51
PCI slot locations, 57
capacities, 51
I/O bridge fan tray, See fan tray assemblies configuration guidelines, 51 to ??
I/O fan tray, See fan tray assemblies handling, 54
I2C bus, 17 memory interleaving, 53, 55
IDE mirroring, disk, 21, 135
parity protection, 21 monitor, attaching, 33
input-device configuration parameter, 43 motherboard, 3, 48, 64, 80, 86, 90, 130
input-device configuration variable, 45, 122 motherboard fan tray, See fan tray assemblies
installing a server, 24 multipathing software, 3, 4, 79, 126, 130, 131
interleaving, memory, 53
internal disk drive bays, locating, 7, 85 N
Internet Protocol (IP) address, 92, 95 network
ISP2100 processor, 87 See also Ethernet
ISP2200A processor, 86, 87 configuring interface, 27, 89
name server, 96
primary interface, 92, 93
J
redundant interfaces, 91
jumpers, 69
types, 27
FC-AL disk backplane, 74
flash PROM jumpers, 72
serial port jumpers, 70
O
ok prompt, See OpenBoot firmware
K OK-to-Remove LED, 12, 146, 155, 157
key lock, 8 OpenBoot configuration variables
auto-boot?, 110 to 113
keyboard, attaching, 33
auto-boot-on-error?, 110 to 114
keyboard/mouse connector, location, 9
boot-device, 111
keyswitch diag-switch?, 112 to 113, 122
Diagnostics position, 36, 74 diag-trigger, 112, ?? to 113
Forced Off position, 14, 38 input-device, 122
effect on RSC, 14, 39 output-device, 122
location, 7, 11 resetting to default values, 122
Locked position, 14, 74, 138
OpenBoot Diagnostics, 5, 22, 59
monitoring and control, 17

190 Sun Fire V890 Server Owner’s Guide • October 2005

 role in automatic system recovery, 109 disabling, 14
OpenBoot emergency procedures, 119 location, 7, 11
OpenBoot environmental monitor, 41, 104 to 109 power cord, AC
See also Environmental monitoring subsystem connecting, 25
automatic thermal shutdown, 105 when to disconnect, 26
disabled by Stop-A keyboard command, 105, power distribution board, 61
107 Power Fault LED, 13, 19
disabling, 41, 104, 107 power supply, 5, 9
enabling, 41, 104, 106 configuration guidelines, 61, 63
obtaining status information, 105, 108, 109 DC output voltages, 63
OpenBoot firmware, 5, 43, 45, 101, 104 to 119 fault monitoring and reporting, 18, 128
operating system software, installing, 93 hot-swap capability, 5, 17, 63
output-device configuration variable, 43, 45, 122 LEDs, 10, 13, 19, 63, 148
overtemperature conditions, 18, 105 location, 9
output capacity, 5, 63, 182
P redundancy, 5, 16, 63, 128
parity, 21, 32, 137 power-on self-test (POST), 5, 22, 119
and RSC, 59
parts checklist, 23
PBCs, 83
Q
PCI bridge chips, 56 to 58
Qlogic ISP2100 processor, 87
PCI buses, 2, 56 to 58
Qlogic ISP2200A processor, 86, 87
availability considerations, 58, 91
configuration guidelines, 56 to 58
parity protection, 21
R
performance considerations, 58 rackmount kit, 6
slot characteristics, 56 RAID, See disk configuration
PCI card rear panel features, 9
configuration guidelines, 56 to 58 reconfiguration boot, 40, 50
device names, 102, 115 redundancy, See hardware redundancy
frame buffer card, 4, 30, 33 reliability, availability, and serviceability (RAS), 6,
host adapters, 3, 4, 20, 79, 84, 86, 90 15 to ??
hot-plug operations, 2, 16, 56, 127 to 130 Remote System Control (RSC), 5, 20, 133, 134
slot characteristics, 56 and keyswitch Forced Off position, 39
slot locations, 9, 57 Ethernet port, 133
slot status LEDs, 57, 144 features, 5, 20, 59, 60, 133
Peripheral Component Interconnect, See PCI card, overview, 5, 20, 59, 60
PCI buses redirecting system console to, 42
physical specifications, 182 serial port, 133, 134
port bypass controllers (PBCs), 83 software installation, 28, 60
.post command, 119 user interfaces, 134
power User’s Guide, 28
LED indicator, 12, 38 removable media devices
specifications, 182 configuration, 67
turning off, 38 removable media devices configuration, 67
turning on, 35 reset-all command, 43, 45, 102, 118, 128
Power button, 13, 37, 38, 41 RSC, See Remote System Control (RSC)

Index 191
S Power LED, 12
safety agency compliance, 184 power supply LEDs, 10, 13, 19, 63, 148
SBus cards, 58 System Fault LED, 12, 18
Thermal Fault LED, 13, 18, 152
SCSI
configuration guidelines, 67 Stop-A keyboard combination, 105, 107, 119
disables OpenBoot environmental monitor, 105,
SCSI Enclosure Services (SES) processor, 83
107
security features, 8, 11, 14 disabling, 14
serial ports, 4, 67 Stop-D keyboard combination, 119
configuring, 27, 67, 70
Stop-F keyboard combination, 120
connecting to, 31
jumpers, 70 Stop-N keyboard combination, 122
location, 9 striping of disks, 21, 80, 137
splitter cable, 4, 31, 68 Sun Cluster software, 139
server installation, 24 Sun Management Center software, 22, 126, 132, 133
service access specifications, 185 Sun StorEdge PCI Dual Fibre Channel Host Adapter
SES processor, 83 card, 86, 87
shipping (what you should receive), 23 Sun Validation Test Suite (SunVTS), 22
show-devs command, 102, 115, 116 SunSolve Online web site, 72
shutdown, 13, 14, 18, 38, 105 system banner, 41
Solaris Operating System, 3, 5, 60, 129, 138 system configuration, See hardware configuration
installing, 93 system console, 4, 30
Solstice DiskSuite, 21, 79, 127, 134, 135 redirecting to local console, 45
specifications, ?? to 184 redirecting to RSC, 42
agency compliance, 184 setting up, 30
clearance, 185 system controller card, 59
DVD-ROM drive, 162 and keyswitch Forced Off position, 14
electrical, 182 connector locations, 60
environmental, 183 hardware configuration, 59
Ethernet cable requirements, 98, 99 location, 9
physical, 182 recovering from failed RSC console, 44
service access, 185 System Fault LED, 12, 18
SSC-100 processor, 83 system features, 1 to ??
status and control panel, 7, 11 front panel, 7
status LEDs, 11 to 13, 21, 141 to 159 rear panel, 9
behavior during POST, 12 system interconnect bus, 50
CPU/Memory board slots, 142 system specifications, See specifications
disk drive LEDs, 7, 85, 156
Disk Fault LED, 12, 156 T
environmental fault indicators, 19 tape cartridge
fan tray LEDs, 66, 152 ejecting, 172
Gigabit Ethernet LEDs, 159 handling, 170
location, 11, 141 to 159 inserting into drive, 171
meaning, 12, 141 to 159 magnetic fields and, 170
OK-to-Remove LED, 12, 142, 144, 152, 156 storing, 170
PCI slots, 57, 144 sunlight and, 170
Power Fault LED, 13, 19 write-enabling, 171

192 Sun Fire V890 Server Owner’s Guide • October 2005

 write-protecting, 171
tape drive
cleaning, 173
controlling with software commands, 173
temperature sensors, 18
terminal, alphanumeric, 4, 31
Thermal Fault LED, 13, 18, 152
thermal shutdown, 18, 50, 66, 105
tip connection, 30
typographic conventions, xxxiv

U
UltraSPARC IV processor, See CPU/Memory board
undertemperature conditions, 18
universal PCI card, 58
Universal Serial Bus (USB) ports, 4, 35
hot-plug feature, 69
Universal Serial Bus ports, 68
hardware configuration, 68
location, 9
USB hubs, 68
USB, See Universal Serial Bus ports
user interfaces, 134

V
/var/adm/messages file, 18
virtual processor, 49
Visual Instruction Set (VIS), 1, 50

W
watchdog, hardware
enabling, 19
weight, See specifications
wrench LED, See System Fault LED, status LEDs
write-enabling a tape cartridge, 171
write-protecting a tape cartridge, 171

Index 193
194 Sun Fire V890 Server Owner’s Guide • October 2005