Dupont Cyrel Global Process-Of-Use Manual
Uploaded by
Wilmer GonzalezDupont Cyrel Global Process-Of-Use Manual
Uploaded by
Wilmer GonzalezDuPont™ Cyrel®
Global Process-of-Use Manual
DuPont Packaging Graphics
“Advancing Flexography”
CYREL® PACKAGING GRAPHICS
Global Cyrel® Process-of-Use Manual
Table of Contents
Section 1. Safety, Health & Environmental Concerns
1‐1 SHE for Cyrel®FAST Platemaking
1‐2 SHE for Cyrel® Solvent Platemaking
1‐3 Cyrel® Material Safety Data Sheet Information
1‐4 Spill Procedure for Solvent Processing Solutions
Section 2. Cyrel® Flexographic Printing Plates
2‐1 Cyrel® Flexo Printing Plates – General
2‐2 Cyrel® Packaging
2‐3 Cyrel® Manual Survey
Section 3. Pre‐Press for Analog
3‐1 Film Negative Specifications
3‐2 Image Distortion
Section 4. Cyrel® Platemaking Process – All Systems
4‐1 Cyrel® Recommended Plate Relief
4‐2 Measuring Printing Plates
4‐3 Exposure Light Source & Monitoring
4‐4 Back Exposure & Step‐Testing
4‐5 Main Exposure & Step‐Testing
4‐6 Post Exposure & Light Finishing
Section 5. Cyrel®FAST Thermal Platemaking System Specifics
5‐1 Cyrel®FAST Platemaking System
5‐2 Cyrel®FAST Platemaking Process Overview
Section 6. Cyrel® Digital Imaging Specifics
6‐1 Cyrel® Digital Imaging System – General Information
6‐2 Cyrel® Digital Platemaking Instructions
6‐3 Determining the Bump Curve
Section 0 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Section 7. Cyrel® Solvent Platemaking System Specifics
7‐1 Cyrel® Solvent Platemaking System – General
7‐2 Cyrel Solvent Platemaking Process Overview
7‐3 Processing Cyrel® Solvent Plates
7‐4 Drying Cyrel® Solvent Plates
Section 8. Cyrel® Processing Solutions
8‐1 Cyrel® Cylosol Processing Solution ‐ NA
8‐2 OptiSol® Processing Solution ‐ NA
8‐3 Processing Solutions ‐ EMEA
Section 9. Handling, Cleaning, Cutting, and Storing Cyrel® Plates
9‐1 Raw Plates
9‐2 Finished Plates
Section 10. Plate Mounting & Demounting
10‐1 Mounting Cyrel® Plates
10‐2 Demounting Cyrel® Plates
Appendix A ‐Quality Assurance
A‐1 General Information
A‐2 Quality Control Checklist
A‐3 Cyrel® Production Log – Solvent Plates
A‐4 Cyrel® Production Log – FAST Plates
Appendix B ‐Printing Ink
B‐1 General Information
B‐2 Solvent Compatibility Guide
Appendix C ‐ Cyrel® Platemaking Troubleshooting Guide
Appendix D ‐ Platemaking Supplies & Sources List
Section 0 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Safety, Health, & Environmental
For Cyrel®FAST Plates & Processing
Safety is always Number One. Making Cyrel®FAST flexographic plates is an
industrial operation. The flexographic platemaking process can be a safe process
when recommended safe handling and work practices are observed.
List of Recommended Personal Protective Equipment (PPE)
• Ultraviolet light – Never look directly at the lighted UV bulbs. If necessary,
during maintenance,
‐ Welding helmet, at least shade 6, or
‐ Welding face shield, at least shade 6
• Condensate
‐ Chemical resistant gloves
‐ Safety glasses with side shields
Suggested Written Programs
• Hazard Communication
– Easily accessible Material Safety Data Sheets (MSDS)
• Standard Operating Procedures (Employee Training)
– PPE
Note: OSHA requires certification that a hazard assessment to determine
appropriate personal protective equipment has been completed.
Safety Recommendations
• Posted safety signs
• Well ventilated, odor‐free plateroom
• Neat, organized work area
• Unblocked access to eye wash station
• Easily available fire extinguisher
– Are employees trained how to use fire extinguishers?
– Are employees trained when to use fire extinguishers?
Section 1-1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
• Functioning safety shield in cutters
• Wooden blocks to hold razor blades
– proper disposal of sharps in approved containers
• Sealed container for rags
• Material handling equipment for developer roll and plates/boxes
• Well‐maintained equipment
Recommended Good Work Practices
• Always handle chemicals with respect
• Do not eat, drink or smoke inside the plate room
• Use appropriate personal protective equipment
– Safety glasses with side shields, any time inside the plate room except
when a higher level of eye protection is required
− Protective gloves
– Chemical resistant gloves (see note below)
when the potential for skin contact with unpolymerized plate material
exists
− removing plates from the processor
− removing developer rolls from the processor
– Leather gloves
when handling boxes of plate material
– Welding helmet (shade 6, at least) or welding face shield (shade 6,
minimum)
− maintenance of exposure unit bulbs
− maintenance of light finisher bulbs
Note: Chemical resistant gloves are made of polymeric material. Discard and
replace the chemical resistant gloves at the first sign of swelling, cracking,
deformation, or break‐through.
Cyrel ® Plates
The plate material consists of three layers, namely: the polyester support, the
photopolymer layer and the coversheet. The polyester support and the
coversheet provide good protection against contact with the photopolymer layer
during handling, cutting and back exposure of the raw plate material. When the
coversheet is removed from the raw plate material, a thin release layer or lams
layer remains on the surface which minimizes direct contact with the
photopolymer layer. The coversheet should not be used for other purposes and
should be recycled or disposed of properly. Processed plates may be handled
Section 1-1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
without personal protective equipment. Handling for inked plates, however,
could be different than handling newly processed plates. Check with the ink
manufacturer for recommendations on handling their ink.
Potential Physical Hazards inside the Plateroom
Lifting
• Cyrel® Developer rolls, both new and used
• A box of plate material
• Flexographic plates
Know the proper way of lifting, use the buddy system and use materials handling
equipment.
Flammability
• Solvent cleaners for negatives
• Rags contaminated with solvents
No smoking or matches are allowed inside the plateroom. Proper grounding for
solvent transfer and for receiving of containers during solvent transfer should be
used. Avoid producing static charges or potential ignition sources. Use proper
flammable storage containers for small amounts. Implement good work practices.
Containers under Pressure
• Full and empty containers under pressure example: glass cleaners
under pressure
Containers should be disposed of properly. A potential hazard is that a container
may explode when burned.
Potential Radiation Hazards inside the Plateroom
Ultraviolet (UV) Light
What is UV light?
• Invisible band of electromagnetic radiation
• Just beyond the violet end of the visible spectrum
Section 1-1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
• Divided into three regions
– Short wavelength (UV‐C)
– Middle wavelength (UV‐B)
– Long wavelength (UV‐A)
• A natural part of our environment, most commonly found in sunlight
Everyone is exposed to UV light (natural and/or artificial) on a daily basis. The
critical organs exposed to ultraviolet radiation are the eyes and the skin. Each
region has a different effect upon the human body.
UV Sources in the Flexographic Platemaking Process
UV‐C, the Short Wavelength (Light Finisher)
• Extends from 180 to 280 nanometers
• Has little penetrating power, however
• Can cause severe burns to the eyes and skin when viewed directly
When UV‐C affects the eyes, the discomfort (intense heat on the eyes) is usually a
delayed reaction (from 5–8 hours after exposure). The discomfort is commonly
known as “welder’s flash” or “ground glass eyeball.”
UV‐A, the Long Wavelength (Exposure/ Post Exposure Units)
• Extends from 320 to 400 nanometers
• Can cause burns to skin and eyes
• Some people experience “blue haze” interference when viewing sources of
UV‐A due to the fluorescent effects in the ocular media
Personal Protection for Ultraviolet Lights
Recommended eye protection is a welding helmet or welding face shield (shade
6 minimum).
Regular vision glasses, regular safety glasses, or regular chemical splash glasses do
not provide adequate protection of the eyes for direct viewing of UV light.
Special UV glasses are not adequate eye protection for direct exposure to UV light.
The protective quality of the eyeglasses needs to match the wavelength range of
the UV light source. UV‐A glasses will not protect from UV‐C exposure and vice
versa. It is easy to make a mistake. The intensity of the UV light source must also
be matched. Intensity increases with the number of sources. Flexographic
equipment has rows of UV lights in both the exposure unit and the light finisher.
Section 1-1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
A UV glass adequate for a single source will not provide protection for
simultaneous multiple sources.
Ultraviolet Light Safety In formation
• Do not defeat or bypass built‐in equipment safety interlock features.
• Do not operate lamps with covers removed.
• Do not stare directly at the operating UV bulbs.
• Do not operate the equipment with covers or access panels removed.
• All personnel OPERATING the equipment should be thoroughly aware of
the hazard.
• All personnel MAINTAINING the equipment should be thoroughly aware
of the hazard.
• UV lamps contain Mercury. Dispose of them according to local, state, and
federal regulations. Recycling is preferred.
• Be careful of reflected UV light, it is as hazardous.
Use appropriate eye protection when observing through the viewing slots.
Minimize viewing time as much as possible.
Never look directly at the ultraviolet light sources. If necessary, during
maintenance:
– Wear the proper protective equipment—welding helmet or
welding face shield, shade 6 at least
– Cover exposed skin, face and arms
– Minimize the time of exposure.
Chemical Safety Information
• Know the hazards, read the MSDS
• No food/no eating allowed inside the plateroom
• Properly designed plateroom HVAC
– Proper plateroom equipment layout
− Efficient workflow
− Clean area
− Do not recycle plateroom air
– Proper exhaust systems
− Seal all horizontal/vertical seams of the exhaust ductwork
− Properly sized external exhaust fan, CFM and static pressure rating
− Proper exit point of the exhaust system
− exhaust directly to atmosphere
Section 1-1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
• Use personal protective equipment, as needed
– Leather gloves
– Safety glasses with side shields
– Welding helmet
• Good work practices
Environmental Issues
Waste Disposal
Safety, environmental and product stewardship are areas in which DuPont has
great expertise and resources. As such, the Cyrel®FAST System process
includes the pickup of used Cyrel® Developer Rolls and Cyrel® boxes in the
United States and Canada. Waste characterization, transportation, paperwork
and incineration are all coordinated through DuPont for the developer rolls,
and the boxes are recycled. In regard to the Cyrel® Developer Rolls, this
reduces customer liability and brings peace of mind knowing the wastes are
incinerated at an approved facility disposed of according to federal, state and
local regulations. If you need additional information about the pickup program,
call your Cyrel® Sales Representative or 1‐800‐345‐9999 (1,4).
Air Permit
With the implementation of the Clean Air Act, air permitting plays an important
role. It is DuPont’s recommendation that, if required according to local, state, or
federal regulations, an application for an air permit for the Cyrel®FAST Thermal
Processing System be completed and submitted to the appropriate authority. This
application allows the permitting board the opportunity to decide whether an air
permit is required to operate the Cyrel® Platemaking System.
Additional Information
See the DuPont™ Cyrel®FAST Pre‐installation, Installation, and Safety and
Operating Manuals for full details on Safety, Health, and Environmental
information.
Section 1-1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Safety, Health, & Environmental
For Solvent Plates & Processing
Safety is always Number One. Making Cyrel® flexographic plates is an industrial
operation. The flexographic platemaking process can be a safe process when
recommended safe handling and work practices are observed.
List of Recommended Personal Protective Equipment (PPE)
• Solvent protection
– safety glasses with side shields
– chemical splash goggles
− chemical resistant nitrile gloves (8 hour stability after solvent contact)
– respirators with organic vapor cartridges
• Ultraviolet light protection
– welding helmet, at least shade 6, or
– welding face shield, at least shade 6
Written Programs Required
• Hazard Communication
– easily accessible Material Safety Data Sheets (MSDS)
• Respiratory Protection Program
• Standard Operating Procedures (Employee Training)
– solvent spill
– distillation
– PPE
Note: OSHA requires certification that a hazard assessment to determine appropriate
personal protective equipment has been completed.
Safety Recommendations
• Posted safety signs
• Well ventilated, odor‐free plateroom
• Neat, organized work area
• Unblocked access to eye wash station
Section 1-2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
• Easily available fire extinguisher
– are employees trained how to use fire extinguishers?
– are employees trained when to use fire extinguishers?
• Functioning safety shield in cutters
• Wooden blocks to hold razor blades
– proper disposal of sharps in approved containers
• Sealed container for rags
• Material handling equipment for solvent handling
• Well‐maintained equipment
Recommended Good Work Practices
• Always handle chemicals with respect
• Do not eat, drink or smoke inside the plate room
• Use appropriate personal protective equipment
– safety glasses with side shields, any time inside the plate room except
when a higher level of eye protection is needed
– chemical splash goggles
− when removing plates from the processors
− when moving drums of solvents, solvents with plate material or stillbottoms
− when transferring solvents from one container to another container
− any time a splash potential exists
− chemical resistant gloves (see note below)
− when the potential for skin contact with solvent or
solvent with unpolymerized plate material exists
− removing plates from the processor
− transferring solvents
− working with solvents during the distillation process
− leather gloves
− when handling solvent drums or boxes of plate material
− welding helmet (shade 6, at least) or welding face shield (shade 6)
− maintenance of exposure unit bulbs
− maintenance of light finisher bulbs
− respirators with organic vapor cartridges
− during spill control and spill clean‐up
− during the distillation process
− whenever the cooking pot is opened
− whenever a task will be done inside the cooking pot
Section 1-2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Note: Chemical resistant gloves are made of polymeric material. The flexographic plate
is a polymeric material. The function of the solvent is to dissolve some polymeric
material. The solvent can also attack chemical resistant gloves. Discard and replace the
chemical resistant gloves at the first sign of swelling, cracking, deformation, or break‐
through.
Cyrel ® Plates
The plate material consists of three layers, namely: the polyester support, the
photopolymer layer and the coversheet. The polyester support and the coversheet
provide good protection against contact with the photopolymer layer during
handling, cutting and back exposure of the raw plate material. When the coversheet
is removed from the raw plate material, a thin release layer or lams layer remains on
the surface which minimizes direct contact with the photopolymer layer. The
coversheet should not be used for other purposes and should be recycled or disposed
of properly. Processed plates may be handled without personal protective equipment.
Handling for inked plates, however, could be different than handling newly
processed plates. Check with the ink manufacturer for recommendations on
handling their ink.
Potential Physical Hazards inside the Plateroom
Lifting
• A drum of virgin solvent, used solvent and/or stillbottoms
• Boxes of plate material
• Flexographic plates
Know the proper way of lifting, use the buddy system and use materials handling
equipment.
Flammability
• Class III A combustible liquid
North America Solvents:
– OptiSol® In‐Line
− flashpoint about 1 5 4 F / 6 8 ° C
– OptiSol® Rotary
− flashpoint about 1 9 6 F / 9 1 ° C
− Cylosol
Section 1-2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
− Flashpoint about 144F / 62°C
EMEA Solvents
− Flexosol In‐Line
flashpoint about 1 3 3 F / 5 6 ° C
− Flexosol Rotary
flashpoint about 1 4 2 F / 6 1 ° C
− Unisol In‐Line
flashpoint about 1 4 5 F / 6 3 ° C
• Solvent cleaners for negatives
• Rags contaminated with solvents
• Transferring solvents
• Wiping plates inside the dryer
No smoking or matches are allowed inside the plateroom. Proper grounding for solvent
transfer and for receiving of containers during solvent transfer should be used. Avoid
producing static charges or potential ignition sources. Do not wipe plates inside the
dryer. Use proper flammable storage containers for small amounts. Implement good
work practices.
Containers under Pressure
• Full and empty containers under pressure, e.g., glass cleaners under
pressure
Containers should be disposed of properly. A potential hazard is that a container may
explode when burned.
Potential Radiation Hazards inside the Plateroom
Ultraviolet (UV) Light
What is UV light?
• Invisible band of electromagnetic radiation
• Just beyond the violet end of the visible spectrum
Section 1-2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
• Divided into three regions
– Short wavelength (UV‐C)
– Middle wavelength (UV‐B)
– Long wavelength (UV‐A)
• A natural part of our environment, most commonly found in sunlight
Everyone is exposed to UV light (natural and/or artificial) on a daily basis. The critical
organs exposed to ultraviolet radiation are the eyes and the skin. Each region has a
different effect upon the human body.
UV Sources in the Flexographic Platemaking Process
UV‐C, the Short Wavelength (Light Finisher)
• Extends from 180 to 280 nanometers
• Has little penetrating power, however
• Can cause severe burns to the eyes and skin when viewed directly
When UV‐C affects the eyes, the discomfort (intense heat on the eyes) is usually a
delayed reaction (from 5–8 hours after exposure). The discomfort is commonly known
as “welder’s flash” or “ground glass eyeball.”
UV‐A, the Long Wavelength (Exposure/ Post Exposure Units)
• Extends from 320 to 400 nanometers
• Can cause burns to skin and eyes
• Some people experience “blue haze” interference when viewing sources of UV‐A
due to the fluorescent effects in the ocular media
Personal Protection for Ultraviolet Lights
Recommended eye protection is a welding helmet or welding face shield (shade 6
minimum).
Regular vision glasses, regular safety glasses, or regular chemical splash glasses do not
provide adequate protection of the eyes for direct viewing of UV light.
Special UV glasses are not adequate eye protection for direct exposure to UV light.
The protective quality of the eyeglasses needs to match the wavelength range of the
UV light source. UV‐A glasses will not protect from UV‐C exposure and vice versa. It
is easy to make a mistake. The intensity of the UV light source must also be matched.
Intensity increases with the number of sources. Flexographic equipment has rows of
Section 1-2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
UV lights in both the exposure unit and the light finisher. A UV glass adequate for a
single source will not provide protection for simultaneous multiple sources.
Ultraviolet Light Safety Information
• Do not defeat or bypass built‐in equipment safety interlock features.
• Do not operate lamps with covers removed.
• Do not stare directly at operating UV bulbs.
• Do not operate the equipment with covers or access panels removed.
• All personnel OPERATING the equipment should be thoroughly aware of the hazard.
• All personnel MAINTAINING the equipment should be thoroughly aware of the
hazard.
• UV lamps contain Mercury. Dispose of them according to local, state, and federal
regulations. Recycling is preferred.
• Be careful of reflected UV light, it is as hazardous.
Use appropriate eye protection when observing through the viewing slots. Minimize
viewing time as much as possible.
If you have to look directly at the ultraviolet light sources,
– wear the proper protective equipment—welding helmet or welding face shield,
shade 6 minimum
– cover exposed skin, face and arms
– minimize the time of exposure.
Chemical Safety Information
• Knowledge of the hazards, read the MSDS
• No food/no eating allowed inside the plateroom
• Properly designed plateroom HVAC
– Proper plateroom equipment layout
− Efficient Workflow
− Solvent contaminated area
− Clean area
– Location of supply air
− Opposite the solvent contaminate area
− “Sweep” the room with fresh supply/make‐up air – okay to recycle
plateroom air, but pick‐up from the clean area of the plateroom
– correct exhaust systems
Section 1-2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
− seal all horizontal/vertical seams of the exhaust ductwork
− properly sized external exhaust fan, CFM and static pressure rating
– correct exit point of the exhaust system
− exhaust directly to atmosphere
− avoid cross‐connections
− to supply air intake
− to recycled air intake
• Use personal protective equipment, as needed
– gloves
– respirators
– splash goggles
• Good work practices
USA Environmental Issues
RCRA Regulations
Wastes generated in the use of the Cyrel® solvent solutions in the USA do not meet the
federal EPA’s (Environmental Protection Agency) definition of hazardous wastes under
the RCRA (Resource Conservation and Recovery Act) regulations.
Waste Disposal
Solvent residues from a distillation recovery unit may contain a small amount of liquid.
DuPont opposes the landfill disposal of any federal non‐RCRA material that does not
meet the EPA’s definition of a solid.
The recommended disposal method for distillation waste is incineration by:
• local municipal incinerator
• commercial direct incineration (EPA permitted TSDF)
• commercial incineration as fuel for energy
This method of disposal eliminates future potential liability in the face of increasing
landfill regulations.
Safety, environmental and product stewardship are areas in which DuPont has great
expertise and resources. As such, DuPont has developed the Cyrel® Waste Network
available to Cyrel® customers in North America. The Network helps participants to
safely handle wastes, such as distillation residue from processing solvent, wet rags,
spent solvents, and empty drums. Waste characterization, transportation, paperwork
and incineration are all coordinated through DuPont. This reduces customer liability
and brings peace of mind knowing the wastes are incinerated at an approved facility
and the ash disposed according to federal, state and local regulations. If you need
Section 1-2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
additional information about the Cyrel® Waste Network, contact your Cyrel® Account
Managers.
Clean Air Act
The OptiSol® /Cylosol alternative solvents do not contain and do not emit a
hazardous air pollutant (HAPS). However, the OptiSol®/Cylosol solvents do emit
some volatile organic vapors (VOCs).
Air Permit
With the implementation of the Clean Air Act, air permitting plays an important role.
It is DuPont’s recommendation that an application for an air permit for the Cyrel®
Solvent Platemaking System be completed and submitted to the State or Local Air
Quality Management Board prior to the installation of the equipment.
SARA Title II
The components of the OptiSol®/Cylosol solutions are not listed in the toxic chemicals
under section 313 of the Emergency Planning and Community Right‐to‐Know Act of
1986 (EPCRA). Section 313 Form R reporting is not required when the OptiSol® /Cylosol
solutions are used.
Section 1-2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Cyrel® Material Safety Data Sheets
The most recent copy of Material Safety Data Sheets (MSDS) for Cyrel® products
other than plate material and developer roll (see below) can be found on the
DuPont Corporate Website. After accessing the website www.dupont.com, click
on “MSDS” at the top of the webpage, choose a country, and then type Cyrel® in
the product name box. You can also contact your Cyrel® Representative for
information.
Cyrel® Plate Material and DuPont™ Developer Roll
OSHA’s Hazard Communication Standard covers the Cyrel® flexographic
plates and developer roll under its article exemption. Under paragraph 29
CFR 1910.1200 (b) (6) (iv), OSHA exempts articles from the requirements of
the Hazard Communication Standard. Cyrel® flexographic plates and
developer roll meet the OSHA definition of an “article” under paragraph (c)
of the Hazard Communication Standard 29 CFR 1910.1200.
29 CFR 1910.1200 (c) Definitions:
“Article” means a manufactured item:
i) which is formed to a specific shape or design during
manufacture;
ii) which has end use function(s) dependent in whole or in part
upon its shape or design during end use; and
iii) which does not release, or otherwise result in exposure to, a
hazardous chemical, under normal conditions of use.
29 CFR 1910.1200 (b) (6) (iv) states:
“This section does not apply to articles.”
Thus, a material safety data sheet (MSDS) is not required and is not available for the
Cyrel® flexographic plates and DuPont™ Developer Rolls.
Section 1-3 Cyrel® Process of Use Manual
CYREL® PACKAGING GRAPHICS
Spill Procedure for Cyrel® Processing Solutions
1. Evacuate spill area immediately.
• Have someone notify supervision and area contacts.
2. Attend to anyone that may be contaminated.
• Contaminated clothing must be removed and contaminated skin flushed
with water for at least 15 minutes.
3. Wear proper personal protective equipment.
• Nitrile gloves
• Chemical coverall splash goggles
• Respirator with organic vapor cartridge
NOTE: If you detect the solvent odor while wearing the respirator, leave the spill area
immediately, change cartridges, re‐check respirator fit, or use a self‐contained
breathing apparatus before returning to the spill. Discard and replace gloves at
the first sign of swelling, cracking or deformation.
3. Clean up the spill.
• Stop and contain the cause of the spill as much as possible.
• Remove any ignition source of heat, sparks or flame.
• Dike spill—seal floor drains if necessary.
• Ventilate spill area.
• Soak up liquid with absorbent material such as blue shop towels, kitty litter, sand, oil
or other commercially available absorbent materials.
• When spilled materials have been absorbed, use brush and scoop to place materials in
an appropriate container. Polyethylene bags may be used for small spills. Five gallon
pails or 20 gallon drums with polyethylene liners may be appropriate for larger
quantities. Handle following your normal waste disposal procedure.
• Decontaminate the surface where the spill occurred with a mild detergent and water,
when appropriate.
Supervision and Area Contacts are: ______________________________________________
Section 1-4 Cyrel® Process of Use Manual
CYREL® PACKAGING GRAPHICS
Cyrel® Flexographic Printing Plates
General
DuPont Packaging Graphics continues to be a global technology leader in supplying
flexographic printing systems. Our scientists continue to develop unique solutions
based on new technologies to assist our customers expand their business by taking
advantage of new profitable packaging printing opportunities. DuPont Packaging
Graphics portfolio of products includes a broad range of Cyrel® brand photopolymer
plates in different thickness, hardnesses and materials for every kind of flexographic
printing application. Platemaking equipment (solvent and Cyrel®FAST thermal
processing), and Cyrel®round sleeves are also supplied.
Cyrel® Printing Plate Portfolio
Productivity - Consistency - Performance - Sustainability
Technology
developments Cyrel® FAST round
Cyrel® round
Cyrel® FAST
Cyrel® Digital
Cyrel® Analog
Product Developments
Cyrel® Plate Manufacturing ‐ ISO‐9001:2000 Certification
Both the Cyrel® Manufacturing sites in Parlin, New Jersey (1990) and Neu Isenberg,
Germany (1988) were among the first plants to be awarded ISO 9001 certification.
Since then, the Cyrel® manufacturing plants, in Parlin, New Jersey and Neu Isenberg,
Germany have continued to recertify, and are covered under an ISO 9001:2000 renewal
certificate. ISO is used as a guideline to help maintain an effective Quality
Section 2.1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Management System, and as an assurance to our customers that we meet all
requirements with respect to quality through consistent products and services.
Features/Benefits
Image Quality–Cyrel® is known for its detailed graphics, fine line work, clean
reverses and superior results on press.
Productivity–Outstanding exposure latitude for single exposure without masking
for even the most critical designs. This means increased productivity and high
quality.
Durability–Exceptional durability for consistent print quality over the longest
press runs.
Dimensional Stability–Provided by the polyester support, assures accurate
image registration.
Thickness Uniformity–Uniform thickness assures minimum make‐ready and
good print quality.
Cyrel® Raw Photopolymer Plate Structure
The Cyrel® plate is a sandwich‐like structure consisting of several layers. An
elastomeric bonding agent is applied to dimensionally stable polyester backing. A
removable, polyester coversheet protects the plate against mechanical damage, dust,
and the desensitizing effects of oxygen.
The photopolymer layer is strongly adhered to the polyester support base, which is
responsible for the plate’s mechanical strength and dimensional stability. Tight print
register can, therefore, be obtained.
The elastomeric binder and light‐sensitive compounds polymerize when the plate is
exposed to ultraviolet light. The polymerization process causes the original physical
properties of the raw materials to be modified in such a way that the bonding agent is
hardened and cannot be removed.
Section 2.1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Cyrel® Analog Raw Plate Structure
Coversheet
Release layer
Photopolymer Layer
Photopolymer Base
Analog plates have a very thin release layer under the coversheet that prevents the
negative from sticking to the photopolymer surface.
Cyrel® Digital Raw Plate Structure
Cover sheet
LAMS
(Laser ablation mask system)
Photopolymer layer
Polyester base
Section 2.1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Cyrel® digital plates do not require the release layer, as no negative is required for
digital platemaking. Instead, bonded directly onto the photopolymer layer is a black,
laser‐imageable LAMS (laser ablation mask system) layer.
Section 2.1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Cyrel® Packaging and Developer Rolls
Printing Plate Boxes and Woodies
Cyrel® printing plates are supplied in reinforced boxes and/or reusable wooden crates
that can be refurbished for reuse. These packaging methods ensure excellent
protection for the fragile printing plates during transport and storage.
Customers in certain locations are offered the opportunity to return these materials for
recycling free of charge to ensure that they are not deposited into the waste cycle. All
internal components of the box, including the foam interleaving sheets between the
raw plates, may also be returned with the boxes. Boxes should be handled with care
so as to prevent damage to them. Contact your Cyrel® Sales Representative for
information on this program.
Cyrel® Plate Packaging Label
In the following illustration you will see a sample of the label that is found on every
box of Cyrel® plate material. Please notice and identify the Run Number/Batch
location. Each box within a batch will have similar back exposure times. When you
change batch numbers, a new back exposure step test is recommended to determine
any shifts in back exposure time.
Plate Type & Quantity Batch Use After
Thickness Plates/Box Number Date
Size
Global Material
Code / Stock #
Section 2-2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Used Cyrel®FAST Developer Rolls
Used developer rolls for the Cyrel®FAST thermal processing system can also be
returned to DuPont free of charge depending on your location.
The used developer rolls should be stored in the same packaging material used to ship
the new developer fabric. First, place the used developer fabric inside the plastic bag.
Place the bag inside the corrugated box. Contact your Cyrel®® Sales Representative
for information on this developer roll return program.
Return Program Availability
Plate Boxes Plate Woodies Packaging Material FAST Developer Rolls
United States X X X X
Germany X X X ‐
Canada X X X X
Section 2-2 Cyrel® Process of Use Manual 2008
Cyrel® Packaging Graphics
Customer Feedback Survey
DuPont continues to research new techniques and technologies to meet customers’ changing quality and productivity needs. This
manual is intended to provide the most up-to-date information and proven techniques available to optimize your use of Cyrel®
products and systems. To be continuously successful, we need your input!!! Please E-mail, fax or mail a copy of this form to:
DuPont™ Cyrel® Packaging Graphics Du Pont de Nemours (Deutschland) GmbH
Customer Technology Center or Customer Technology Center
P.O. Box 80702 Hugenottenallee 173 -175
Wilmington, DE 19880-0702 USA 63263 Neu-Isenburg, Deutschland
Fax: (302) 999-4579 Fax. +49(0)6102-18-3968
E-mail: [email protected] E-mail: [email protected]
Company ________________________________________________________________________________________
Submitted by _______________________________________________ Title _________________________________
Address ___________________________________________________ Telephone ____________________________
City _______________________________________ State _________________________ Zip ___________________
Please indicate a response which best reflects your opinion of the Cyrel® Process of Use Manual.
Please place an “X” or circle and/or write response (reference section, if necessary).
Poor Excellent
Ease of Use
Content 1 2 3 4 5
Organization 1 2 3 4 5
Illustrations/Diagrams/Charts 1 2 3 4 5
Coverage of the flexo process (creation to print) 1 2 3 4 5
What information do you find most valuable? __________________________________________________________________
What topic(s) do you find least useful and why? ________________________________________________________________
What else would you like to see in our Manual? ________________________________________________________________
What is your overall satisfaction level with the value you receive from Cyrel® flexographic plates and related products/systems
that you purchase from DuPont? What one thing would you most like to see improved?______________________________
What actions could DuPont take to better understand your customers’ up and coming trends and needs in order to better satisfy
your requirements for flexographic printing equipment and consumables? ___________________________________________
Other comments or upgrades: ______________________________________________________________________________
A sincere “Thank You” for your feedback!
Section 2‐3 Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Film Negatives
Each Cyrel® plate is an original and can only be as good as the negative from which it
was produced. The plate cannot be changed after it is produced. There are basic
specifications that film must meet in order to produce the highest quality Cyrel®
printing plates. Always check the negative for these requirements before imaging the
plate.
High Matte Surface‐—Only films with a high matte surface will ensure that the air
between the plate surface and the film is extracted without leaving any air bubbles,
and that sufficient contact between film and plate is achieved. Matte level can wear
after repeated use of the film. This would adversely affect the plate image.
Dmin (Minimum Density)—A Transmission Densitometer reading of .05 or less in the
clear area is required. This assures that the negatives are fully translucent in the
transparent areas in order that fine image elements will be properly exposed and
reverses are clean.
Dmax (Maximum Density)—A Transmission Densitometer reading of 4.0 (4.50 for
Cyrel®FAST) or more in the black area is recommended for analog Cyrel®FAST plates
to achieve the highest quality printing plates. Density lower than 4.0 will cause burn‐
through during plate exposure. This will lead to loss of relief and unwanted image on
the floor of the plate.
Proper Image Orientation—A right‐reading, emulsion‐up negative (RREU) is oriented
for face printing while the reverse‐reading, emulsion‐down negative (RRED) is for
reverse printing. Normal surface printing generally requires right‐reading negatives.
They produce a wrong‐reading printing plate and subsequently a right reading printed
image.
Right‐Reading = readable from the matte film emulsion side.
Wrong Reading = readable from the glossy, back side of the film.
Section 3-1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Scratches and Pinholes—Negatives should be free of scratches, pinholes, or any other
marks on the clear area of the film. These marks will reproduce on to the
photopolymer plate. This is usually caused by the change in Dmin or from the removal
of some of the emulsion from the film. Opaque should always be applied to the base
side of the film only. Retouching on the emulsion side of the film can cause poor
contact between the negative and the plate.
Kinks—A kink in the image area will reproduce on plate. Care in handling the film
will reduce the possibility of kinks. It is recommended to carry negatives corner to
corner on a diagonal.
Film Thickness—Graphic Arts film is available in two thicknesses, 4 mil and 7 mil. A
7‐mil thickness film is preferred to reduce the possibility of kinks during handling and
storage.
Proper Distortion—Film negatives must be properly distorted to allow for elongation
in the print direction. The photopolymer thickness and repeat length of the job
determines the distortion percentage (see Film Reduction Factors).
Section 3-1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Distortion
When a photopolymer printing plate is laying flat the top surface and the bottom
surface of the plate are the same length, X=Y (see diagram 1).
Y
Diagram 1
X
When the plate is wrapped around a printing cylinder (see diagram 2) the surface of
the plate becomes stretched because the distance around the surface is greater than the
distance around the back of the plate (Yd>X d)
Yd
Xd
Diagram 2
Since the plate is imaged flat and printed round, the original negative must be reduced
(distorted, only in the direction it will be wrapped around the cylinder) so that upon
stretching it becomes the proper size.
The plate elongates in the print direction (around the cylinder) because the plate
material is elastic. The top of the photopolymer stretches around a larger
circumference than the bottom. The % reduction needed to compensate for this
elongation can be calculated by the following equation:
Section 3‐2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
% Reduction = (1 – K) x 100% = (R – K) x 100%
R R
where K = Elongation Length, R = Repeat Length
The value obtained corresponds to the percentage reduction of the original in the
printing direction.
K = Elongation Length
K is the extra length that the top of the photopolymer stretches around a cylinder
compared to the bottom. Its value depends on the thickness of the photopolymer (t),
which is the plate thickness, minus the polyester support thickness (the rigid support
does not elongate). For polyester support thickness, see chart on next page. Contact
your Cyrel® Sales Representative for any specialty products.
For these calculations, we will approximate the factor π as 3.142.
K = 2 π t
Example: Cyrel® 112UXL
K = 2 π t
= 2 π x (plate thickness ‐ polyester thickness)
= 2 x 3.142 x (0.112–0.005)
= 2 x 3.142 x 0.107
= 0.672”
Section 3‐2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
The following table shows the various pre‐calculated constant K values for different
Cyrel® plate thickness:
Cyrel® Base
Thickness K (inches) K (cm) Thickness_____
.045 in/1.143 mm (FOP/CL4) 0.220 0.559 .010 in/.254 mm
.045 in/1.43 mm (not Coating)0.239 0.606 .007 in/.178 mm
.067 in/1.70 mm 0.390 0.990 .005 in/.127 mm
.090 in/2.29 mm 0.534 1.357 .005 in/.127 mm
.100 in/2.54 mm 0.597 1.516 .005 in/.127 mm
.107 in/2.71 mm 0.641 1.628 .005 in/.127 mm
.112 in/2.85 mm 0.672 1.708 .005 in/.127 mm
.125 in/3.18 mm 0.754 1.915 .005 in/.127 mm
.155 in/3.93 mm 0.943 2.394 .005 in/.127 mm
170 in/4.32 mm 1.037 2.634 .005 in/.127 mm
185 in/4.70 mm 1.131 2.873 .005 in/.127 mm
250 in/6.35 mm 1.539 3.910 .005 in/.127 mm
R = Repeat Length
The repeat length (R) is normally specified with the print job, in which case it is simple
to calculate the reduction factor.
If the repeat length is not known, it is best obtained by measurement from the printed
sheet.
Alternatively, knowing the radius of the printing cylinder, the thickness of the double‐
sided adhesive tape, and the plate thickness, the repeat length can be calculated using
the following equation:
R = 2 π x (cylinder radius + adhesive tape
thickness + plate thickness)
Section 3‐2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Example: Cyrel® 112UXL plate mounted on a 4.5” diameter cylinder using 3M 411
tape (.015” thickness).
R = 2 π x (cylinder radius + adhesive tape
thickness + plate thickness)
= 2 π x (2.250 + .015 + 0.112)
= 2 π x 2.377
= 2 x 3.142 x 2.377
= 14.937”
Examples
Let’s complete the following two examples. As needed, the K values and the repeat
length R have been calculated in the previous sections.
Example 1: Cyrel® 112UXL plate mounted on a 4.5” diameter cylinder using 3M 411
tape (.015” thickness). What would be the film reduction factor?
% Reduction = (1 – K) x 100%
R
= (1 – 0.672) x 100%
14.937
= (1 – 0.0449) x 100%
= 100% – 4.49%
= 95.51% of original
Section 3‐2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Example 2: Cyrel® 112UXL plate mounted on a cylinder with a 15” repeat. What
would be the film reduction factor?
% Reduction = (1 – K)
x 100%
R
= (1 – 0.672) x 100%
15
= (1 – 0.0448) x 100%
= 100% – 4.48%
= 95.52% of original
Section 3‐2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Cyrel® Plate Relief
Each Cyrel® plate is manufactured with a minimum floor thickness above which there
is a layer of unpolymerized material. This allows platemakers to select their own relief
by varying back exposure time. For the best print quality and performance, however,
the recommended relief for all Cyrel® plates is listed below.
Plate Thickness Recommended Relief*
Inches mm Inches mm
.045 1.14 .018‐.022 0.45‐0.55**
.067 1.70 .018‐.025 0.45‐0.65**
.090 2.29 .020‐.035 0.50‐0.90
.100 2.54 .020‐.035 0.50‐0.90
.107 2.72 .020‐.035 0.50‐0.90
.112 2.84 .020‐.035 0.50‐0.90
.125 3.18 .035‐.050 0.90‐1.25
.155 3.94 .055‐.075 1.40‐1.90
.170‐.276 4.32‐7.01 .060‐.100 1.50‐2.50
*The minimum relief is recommended for best print quality, performance, tighter
registration, and less press bounce.
**For Cyrel®FAST plates, consider that the maximum for .045 in./1.14 mm plate should
not exceed .024 inch/ 0.6 mm and for .067 in./1.70 mm you should not exceed .028
inch/0.7 mm .
Section 4-1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Measuring Cyrel® Plates
The choice of a digital thickness gauge and method of measurement are important for
obtaining correct data. The printing image of a processed plate can be easily
compressed, and any heavy pressure exerted by the measuring device will lead to false
readings.
Several points should be measured on a plate to determine the average thickness of the
plate. When measuring raw plates, the plate should be measured with the polyester
coversheet intact. The coversheet is 0.004”/.102 mm thick for most plates. Subtract this
number for the absolute plate thickness. It is not possible to accurately measure the
thickness of fine type or screen areas with conventional equipment. Stationary digital
micrometers, which apply minimum pressure on the printing image, are the most
commonly used in the industry. The recommended range of measurement should be
(0.039‐390 mil) 0.001‐10 mm with an accuracy of +/‐ 0.39 mil (+/‐ 0.01 mm).
The following general recommendations will help ensure good results when using a
digital micrometer.
Calibration of the micrometer should be checked routinely with accurate machinist’s
blocks of determined thickness.
Make sure the measuring foot is flat and not loose.
The measuring table should be sufficiently large, smooth, and level (polished steel or
stone) to allow the plate to lie flat at the gauge foot.
The micrometer foot should be parallel with the micrometer base.
The measuring foot should also be flat with a minimum diameter of 0.25 inch/6.350
mm.
The area to be measured should be at least ½ inch/9 mm square.
The contact pressure of the measuring foot must not exceed 1.5N.
The polyester backing and the measuring table must be perfectly clean to obtain
accurate thickness data.
Section 4‐2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Exposure Light Sources
Despite the introduction of new light sources, fluorescent tubes are still predominantly
used to expose photopolymer plates. Digital plates should only be imaged with
conventional fluorescent tubes. The reason for this is the limitations of newer light
sources. Cross‐linking of the photopolymer occurs most efficiently at maximum wave
length of 350‐365 nm. Exposure bulbs (UVA) for back exposure, main exposure, post‐
exposure should be purchased in this range. To prevent overheating of the equipment,
only original tubes with the recommended power should be used. We recommend
high output bulbs 10R from Philips.
Light Intensity
UV output of the bulbs influences exposure times. As the exposure bulbs age, light
intensity falls off, and exposure times increase. The consistency of the bulbs can also
begin to vary within the exposure unit, and this can affect image exposure.
Monitor the UV output of new exposure bulbs on a regular basis for the first 100 hours.
If a UV meter is not available, exposure bulbs should be burned in a minimum of 10
hours before plates are made. The strength of new exposure bulbs usually shows an
increase in measured intensity for the first 10 or so hours of operation. After
approximately 10 hours, there will be a slight decrease in measured intensity. This, in
turn, will be followed by a “leveling‐off” in measured intensity.
An initial reading of the exposure bulbs should be taken after the burn‐in period or
when the bulbs level off. The bulbs should also be checked periodically (200, 400, 600
hours) for intensity and consistency of irradiance (output). An hour meter on many
exposure units is provided for this purpose. Bulb readings and what would be
considered the normal operating range will vary depending on the particular exposure
unit and the age of the exposure bulbs.
Changing Exposure Bulbs
As mentioned above, back and main exposure bulbs must be adjusted to compensate
for the fall‐off of bulb irradiance. The expected useful lamp life for high intensity
Philips 10R bulbs is up to 800 hours, depending on the number of times the unit is
turned on and off. However, when exposure times become too long, the bulbs should
be changed.
Section 4‐3 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
For optimum quality, the easiest and most reliable method for checking bulb output is
to use a UV output measurement device, such as the Kühnast meter, at regular
intervals. It is especially important to track UVA output for digital plates. The
minimum UVA bulb output for optimum quality plates (especially digital) is 13
mW/cm2, and a variability of +/‐10% of the average measurements of the exposure unit.
Change all exposure bulbs at once. Make sure the opaque or reflector side of the lamp
is facing the proper direction (away from the exposure bed). For a more uniform UV
intensity, alternate bulb placement (when inserting bulbs) in the exposure unit based
on the “logo” located on one end of each bulb.
If one exposure bulb goes out, and you do not replace all the bulbs at once, the new
bulb should be placed in the back of the unit.
Procedure for Testing UV Exposure Bulb Output
1. Inspect main, back, and light finishing exposure bulb intensity at regular intervals
(monthly is recommended).
2. Use exposure frame template below for placement of bulb meter 1‐9.
Section 4‐3 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Lamp Reading Locations
Front of Exposure Unit
3. Pre‐heat bulbs at least 3 minutes. Test exposures are dependent on the type of UV
meter you are using. We recommend Kühnast UV Meters (available for UVA and
UVC), which are best for this application. Information for ordering these meters can be
found in the Platemaking Supplies and Equipment List elsewhere in this manual.
4. Calculate both the average value and the total variability (high‐low) of the nine
readings.
5. Bulbs should be changed when the maximum variability within the unit is 20% (+/‐
10% from the average value).
6. Record readings on a log similar to the sample table below.
Bulb Intensity Bulb
Reading
Tester Date 1 2 3 4 5 6 7 8 9 AVG Status Notes
Section 4‐3 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Cyrel® Photopolymer Plate Back Exposure for Cyrel® Plates
Step 1: Back Exposure
Plate is exposed from the back
(through the base)
Back Exposure is the first step in printing plate production. A standard back exposure
step test is conducted to establish the time required to obtain a desired relief. It occurs
through the plate’s polyester base prior to main exposure (Step 2). The exact back
exposure time is determined by a back exposure step test.
Back exposure also has several important functions:
1. It sensitizes the plate to reduce the main exposure time,
2. It establishes the required relief,
3. It improves the adhesion between the polyester support and the layer of
photopolymer,
4. It provides a firm base for fine lines and screens, and
5. Correct back exposure also helps produce a proper dot profile in conjunction with
proper main exposure.
The sensitizing process takes place during the first few seconds of back exposure, after
which the floor is gradually built up to a pre‐selected level. It is recommended to back
expose plates immediately before main exposure. Delays can result in significant
variation in relief depth and main exposure times.
During the sensitizing phase, most oxygen, which has diffused into the plate during
storage, is consumed. Because polymerization has not yet begun, no build up
of the floor takes place. When most of the oxygen has been consumed, polymerization
begins and the floor starts to build up. The longer the back exposure time, the higher
the floor, and the smaller the relief. Polymerization is a complex reaction in which
radicals combine to form molecular chains which then crosslink to build a molecular
network. The polymerization reaction changes the original properties of the
photopolymer that becomes insoluble in an organic solvent or cannot be melted by
thermal contact.
Section 4‐4 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Figure 1
More exposure=thicker floor/shallower relief.
Less exposure=thinner floor/deeper relief.
Example: In the Figure 1 above, a back exposure time of 28 seconds has built the
floor up to a thickness of .046 inches, which for a Cyrel® .067 plate corresponds to a
relief of .021 inches.
When to Perform a Back Exposure Step Test
Performing back exposure tests regularly saves you time and insures that the best
consistent, quality plates are produced.
For consistent results, back exposure step tests should be performed
For consistent results, back exposure time needs to be established for:
for:
1. Each new batch of Cyrel® plates (See Product Label in Cyrel® Flexo
Plate ‐ Packaging Section for location of batch number.)
2. After new exposure bulbs have been installed and burned in
3. For each product type you use
Section 4‐4 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Back Exposure Step Test Procedure
Safety Information
Exposure Units
UV Source Used during Back Exposure
Long Wavelength (UV‐A –350‐400 nm)
Recommended PPE: Never look directly at the lighted UV bulbs. If necessary, during
maintenance, a welding face shield with shade 6 is recommended.
Ultraviolet Light Safety Information:
Do not defeat or bypass built‐in safety features of the equipment.
Single‐Bank Exposure Unit (Example – DuPont 2000E Exposure Unit)
1. Preparation of a test plate
Cut a test strip of raw plate material
approximately 5” x 15” (15x40cm) for rotary processing, 12” x 30” (30x75cm)for
inline and thermal processing, or an appropriate size for your processor. On the
surface of the polyester support, mark off six or more equal segments at least 3
inches/ 8 cm in width with the appropriate exposure time intervals that includes a
range of guideline times supplied by DuPont or times based on previous exposure
times you established for the product. For Cyrel®FAST plates, the marked
segments should be at least 6 inches / 15cm in width in order to get smooth and
accurate results.
If you have determined that 25 seconds is a good starting estimate, begin with the
middle step at 25 seconds (Figure 2) and continue with several additional steps on
each side of the starting estimate. Mark off your steps on the back of the plate with a
black, permanent marker so that the lines and numbers will be imposed into the
plate (Figure 3).
Create a Solid Area
For Cyrel® FAST plates, leave sufficient space at the end of the strip for a solid area.
This solid area must be in the same direction as the segments and next to longest
backflash time segment. This creates a solid step for checking relief when test is
completed.
Section 4‐4 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
This solid will also serve to properly clamp the step test plate into the FAST
processor. You will back expose the solid strip the same time as your longest step
next to it.
For solvent plates, create a solid with one‐half of your step test plate (Figure 4).
Next, place a strip of high density stripping tape across the center back of the test
plate (Figure 4). This tape blocks the light to prevent polymerization of the plate
material under the tape. We can then verify washout performance.
Figure 3
Figure 2
Stripping tape
Solid step for Cyrel®
FAST plates
Solid step for Cyrel®
Figure 4 Solvent plates
2. Pre‐heat the back exposure lamps.
For optimum consistency in plate relief it is important to attain a stable operating
bulb irradiance on the exposure bed, especially with the short exposure times for
thinner plates. Warm up the UV lamps in the exposure unit if the unit has not been
used within ten minutes. You can determine the required length of pre‐flashing
time on your equipment by measuring how long it takes a particular exposure unit
to reach its stable UV energy output. Some units may reach the stable point in 2
minutes, others may take longer. Back exposure step test conditions should simulate
production conditions as closely as possible. Once the bulbs are warmed up, begin
the step test and each step exposure within 30 seconds.
Section 4‐4 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
3. Place the plate on the exposure unit.
Place the marked plate on the exposure unit with the coversheet facing downward.
No vacuum is used during back exposure. Obtain two pieces of masking material.
All masking material used for the step tests should measure at least 4.0 D‐max or
greater to prevent light leaks.
4. Expose each segment for the proper time interval
using the “individual” or “cumulative” exposure method described below.
For .090/2.28 mm thickness plates and thinner, with the back exposure segments of
shorter than 10 seconds, expose according to the “individual exposure method” listed
below.
For other plate thickness, with back exposure segments of 10 seconds or more, expose
according to the ”cumulative exposure method” listed below.
A. Individual Exposure
To expose the segments individually, lay two pieces of masking material directly on
the plate or exposure bed (depending on exposure unit), spacing the two masks
apart the exact distance of each stepped interval.
Expose each segment individually for the entire time interval, beginning with the
longest individual time exposure. Example time segments are shown below.
Segments: 13, 16, 19, 22, 25, 28, 31
Mask the 13‐31 second segments and expose the last segment and the solid segment
for 34 seconds (Figure 5).
Figure 5
Section 4‐4 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Adjust masking material on plate to cover the 13‐28 and 34 second segments and
expose the revealed segment for 31 seconds (Figure 6).
Figure 6
Continue this progression until all segments are exposed.
B. Cumulative Exposures
Example cumulative time segments (Figure 7):
Segments: 40, 50, 60, 70, 80, 90, 100
Stripping tape
Figure 7
The entire back of the plate is first exposed for the shortest time interval. A mask is
placed covering the top of the plate completely.
Then, mask the shortest time interval (40”) and expose the remaining time intervals
for 10 more seconds (Figure 8).
Figure 8
Advance the mask to cover the 40 and 50 second time segments and expose the
remaining time intervals for 10 more seconds (Figure 9).
Section 4‐4 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Figure 9
Continue the progression of 10 seconds until each segment has been given the
proper time by cumulative time exposure.
C. Specifics for Dual‐Bank Exposure Unit ( Steps 1‐4)
1. Preparation of a test plate
Cut a test strip of raw plate material
approximately 5” x 15” (15x40cm) for rotary processing, 12” x 30” (30x75cm)for
inline and thermal processing, or an appropriate size for your processor. On the
surface of the polyester support, mark off six or more equal segments at least 3
inches/ 8 cm in width with the appropriate exposure time intervals that includes a
range of guideline times supplied by DuPont or times you have previously
established for the product. For Cyrel®FAST plates, the marked segments should
be at least 6 inches / 15cm in width in order to get smooth and accurate results.
Identify the time intervals on the bottom back of each segment with a black
permanent marker. Place a strip of high density stripping tape across the center
back of the test strip. This tape will block the light so that you can check for
complete washout of the polymer.
2. Pre‐heating of the back exposure lamps is not needed for dual bank exposure units.
Dual bank exposures units are conditioned on a stable temperature.
3. Place the marked plate on exposure unit and mask.
Keep the coversheet intact and place the plate so that the coversheet faces upward.
No vacuum is used during this step. Obtain two pieces of masking material. All
masking material used for the step tests should measure at least 4.0 D‐max or greater
to prevent light leaks. This will give you the most accurate floor results.
4. Expose each segment for the proper time interval
using the “individual” or “cumulative” exposure method described above.
End of Specifics for Dual‐Bank Procedure – Continuing with main procedure
below
Section 4‐4 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
5. Main expose a solid area for clamping into the machine and measuring relief.
For solvent analog plates:
When exposure of the step intervals is complete, place masking material on top of
the coversheet, leaving the top segment uncovered (Figure 10). This top segment of
the plate will be main‐exposed to create a solid. This segment will be clamped into
the machine for processing and will also provide a solid for measuring relief.
Figure 10
For solvent digital plates:
When exposure of the step intervals is completed, remove cover sheet and place
masking material on top of the mask, leaving the top segment uncovered(same as
Fig.10). Place sticky tape across the mask on the top section of the test. Then remove
the black mask by pulling off the sticky tape creating a clear area on the plate. When
imaged, this will create a solid.
6. Before processing coversheet and stripping tape must be removed (Figure 11).
Process according to the required plate type and thickness.
Figure 11
Section 4‐4 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Additional Cyrel®FAST Exposure and Processing Specifics
A. The back exposure test sample should be minimum of 12x30” (30x75cm). The
marked segments should be at least 6 inches / 15cm in width. Refer to analog and
digital solvent procedure above for all other back exposure steps.
B. Be sure to clean off the black markings before processing with film cleaner or
alcohol. Otherwise, they will transfer off onto the white drum skin of the
Cyrel®FAST processor (Figure 12).
Figure 12
C. The Cyrel®FAST back exposure step test plate must be processed in the vertical
position through the machine (Figure 13) clamped on the solid segment. This
allows the heated roller to engage the plate uniformly across each step. Use the
appropriate Cyrel®FAST processor program for the plate thickness of the test.
Figure 13
Section 4‐4 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Continuing with main procedure steps
7. For solvent‐processed plates, dry the washed out plate for minimum 20 minutes
(minimum) at 140° F / 60°C and allow it to cool to room temperature.
8. Measure the relief depth.
Zero out the digital micrometer on the metal base. Take a measurement of the
solid area to determine the plate thickness. Measure the corresponding stepped
segment below that solid area three times and take the mean value.
Subtract the measurement of the stepped segment from the thickness of the solid
area. This value is equal to the relief depth. The relief depth will correlate with the
amount of back exposure for each segment. Continue to measure the solid area to
the stepped segment (Figure 14 and 15).
Solid Area
Stepped Segments
Figure 14 – Solvent Plates
Figure 15 – Cyrel® FAST Plates
9. Select the back exposure time that provides the desired relief or draw a diagram
(Figure 16) of times to relief and choose the recommended relief depth with
corresponding time.
Backflash Test
1,8
Relief depth in mm
1,6
1,4
1,2
Relief depth in
1
mm
0,8
100 HOS
0,6
0,4
0,2
0
10 15 20 25 30 35 40
exposure time in s
Figure 16
Section 4‐4 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
10. For solvent plates only, return plate to dryer to complete drying time.
11. After drying is completed, measure the relief depth (step 7) to verify the previously
selected back exposure time.
12. Retain the back exposure information for use on this batch of Cyrel® plates, and
record the back exposure time on your Cyrel® Production Log. Daily use of the
Cyrel® Production Log to record processing data will improve production
efficiency. The results of previous jobs will then be available to guide new jobs and
information will be available for troubleshooting. The Cyrel® Production Log can
be found in the Quality Assurance section of this manual.
Section 4‐4 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Cyrel® Photopolymer Plate Main Exposure
Step 2: Main exposure
The face of the plate is exposed
through the film negative or LAMS‐layer.
Main exposure is the second step in the production of photopolymer plates and
should be performed immediately following back exposure. The purpose of main
exposure is to create the relief image for the printing plate and to ensure that the
image elements are firmly anchored to the relief base built up during back exposure.
Main exposure is carried out through a film negative or laser‐ablated plate and
forms the printing image. Ultraviolet light that passes through the clear areas of the
negative or mask causes a polymerization reaction. The exposed photopolymer
cannot be removed in the processing step, thus creating the relief image. Main
exposure time is affected by:
Polymer Type
Polymer Thickness
Condition and type of platemaking system
Age and type of the exposure bulbs
Temperature of the exposure bulbs
Solvent
Image Detail
Plate Relief
Transparency of the vacuum coversheet material
(analog only)
Section 4‐5 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
For these reasons, we recommend that a Main Exposure Step Test be performed:
• After burn‐in of new exposure bulbs
• For each product type & thickness you use
• If there is a change in your platemaking system
(Exposure unit, Processor, Solvent)
• As exposure bulbs age & bulb output decreases
• Any change in the platemaking process
Main Exposure Step Test Procedure – Solvent Plates
Safety Information ‐ WARNING: Potential Physical Hazard—Radiation
Exposure Units
UV Source Used during Main Exposure
Long Wavelength (UV‐A – 350‐400 nm)
Recommended PPE: Never look directly at the lighted UV bulbs. If necessary,
during maintenance, a welding face shield with shade 6 is recommended.
Ultraviolet Light Safety Information:
Do not defeat or bypass built‐in equipment safety features.
Do not stare directly at the UV bulbs.
Do not operate equipment with covers or access panels removed.
All personnel operating and maintaining the equipment should be thoroughly
aware of the hazards and use appropriate personal protective equipment.
Refer to manufacturer’s equipment manual for safety requirements when
viewing UV light through viewing slots.
1. Sample Preparation ‐Cut a test strip of raw plate material
For analog plates, cut a piece of raw polymer to fit the main exposure step test
negative. For digital plates, you can tack the step test image onto the end of a
job if you have space, or if imaging the step test image alone, you need to cut
enough raw material to image the file and to go around the drum.
Section 4‐5 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
2. Pre‐heat the back exposure lamps.
For optimum consistency it is important to attain stable operating bulb
irradiance on the exposure bed. The UV bulbs should be warmed up for at least
three minutes. If you have a UV meter, such as the Kuhnast meter, you can
determine the required length of pre‐flashing time on your equipment by
measuring how long it takes a particular exposure unit to reach its stable UV
energy output. Some units may reach the stable point in two minutes, others
may take longer. Also, UV lamps in the exposure unit should be warmed up if
the unit has not been used within ten minutes. Back exposure step test
conditions should simulate production conditions as closely as possible.
3. Back expose the plate for a pre‐selected time that will produce the
desired relief (determined by the back exposure test).
4. Prepare the plate for exposure.
5. For single bank exposure units, place the back exposed, raw plate on the
exposure unit bed, with the coversheet intact and facing upward. Remove the
coversheet in one smooth motion and discard. You can distinguish the
coversheet by flicking the edge of the plate.
For analog plates:
Place the test negative on the Cyrel® plate, emulsion‐side (matte surface)
in contact with the plate surface. A test file is available from DuPont.
Clean the back of the negative with antistatic film cleaner, roller, or tack
cloth.
• Place the masking strips around the edges of the negative and plate
down to the exposure bed floor. Masking strips help create contact
between he negative and plate surface. Masking strips must have a
matte or air‐channeled surface to allow air to escape (i.e., DuPont
masking strips). Make sure that the masking strips extend to the
vacuum channels of the exposure unit surface.
Section 4‐5 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Masking material for
Dual Bank Exposure Bed
For glass exposure beds (dual bank exposure units), masking material must
be placed to cover all exposed glass so that UV light will not be reflected
from the upper bulb bed. The lifetime of masking strips is limited. They
need to be checked regularly and replaced as soon as the embossing is worn.
Draw the vacuum coversheet and pull vacuum (~.8 bar or ~25 in. on gauge,
.99 on ECLF).
For digital plates:
Laser‐ablate a unbumped main exposure step test image onto a plate. A
test negative file is available from DuPont.
Place the laser‐ablated plate on the exposure unit bed.
No vacuum coversheet is required for main exposing digital plates.
5. Main expose the entire test plate for the smallest amount of time in the range of
expected exposure times. Then cover one image copy using opaque material and
add exposure intervals of 2 minutes, repeating the procedure until the last copy
of the target is exposed. The test plate should result in main exposures that
Section 4‐5 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
range from being slightly under‐exposed at the first segment to being slightly
over‐exposed at the last segment.
6. Process the plate.
Area to be clamped Recommended processing
direction for all systems.
7. For solvent plates, dry the plate thoroughly for at least 20 minutes in
the dryer. At this point, check the plate for solvent spots, missing images, etc.
Return the plate to the dryer to complete the drying time. If solvent spots are
apparent, remove plate from the dryer (or shut the dryer off), and wipe the spots
with an antistatic film cleaner or a mixture of 50% alcohol and 50% water.
8. Post expose and light finish the test plate.
9. Document the batch number on the test plate and save this test in the box of
plates for reference.
Evaluating Main Exposure Step Test
The correct exposure is the one where you hold your finest detail (fine lines and
type) and a consistent minimum dot (with no dot dropouts), and keep your reverses
open. The main exposure time should be as long as necessary and as short as
possible.
Check the integrity of the plate images for the following qualities when completed.
A complete Quality Control Checklist for a finished plate is available in the Quality
section of this manual.
Section 4‐5 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
1. Positive characters should have a sharp, clean shoulder.
2. There should be no positive dot drop‐outs for the targeted
% dot you wish to produce.
3. All positive dots on the targeted screen should be well‐
defined and of the same height. No dots should be falling
over, missing, or chipped. Isolated dots should be present
and well‐anchored to the base.
4. Positive lines should be sharp, clean, and straight. They
should not be wavy or chipped.
5. Reverse areas, dots, and lines should be open, clean, and
sharp.
6. Check that the relief is correct.
Image Resolution
For digital plates, choose the shortest main exposure time that holds your smallest
dot at a consistent size and height. There is no advantage to choosing a longer
exposure time. Digital plates are usually capable of holding 1‐98% dots.
For analog plates, choose the proper main exposure time to hold the finest detail
while keeping fine type and reverses open. Analog Cyrel® plate are usually capable
of holding 2–95% dots (some exceptions).
Refer to the Cyrel® Product Data Sheets for specific imaging capabilities of Cyrel®
plates.
Main Exposure of the Cyrel® Plate
As mentioned previously in main exposure step test section, main exposure is
carried out immediately following back exposure. As with all exposures, it is
important to attain stable operating bulb irradiance on the exposure bed for
optimum consistency. The UV bulbs should be warmed up for at least three
minutes, especially if the exposure unit has not been used for ten minutes.
Section 4‐5 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Main Exposure for Analog Plates
1. Clean the emulsion or matte side of the negative with antistatic film cleaner, tack
roller, tack cloth or magnetic wiping cloth to insure no dust or dirt interferes
with the plate image quality. Do not use any cleaner that will leave a residue on
the film surface.
2. For single bank exposure units, place the back exposed, raw plate on the
exposure unit bed, with the coversheet intact and facing upward. Remove the
polyester coversheet in one smooth motion and discard. You can distinguish
the coversheet by flicking the edge of the plate.
3. Position the negative with the emulsion side in contact with the plate surface.
Clean the back of the negative with antistatic film cleaner, tack roller or tack
cloth.
4. Place masking strips over the edges of the negative and the plate, as explained in
the #5 of the main exposure step test procedure above.
5. Turn on the vacuum.
6. Unroll the vacuum coversheet over the plate and negative. As you unroll, use a
lint‐free cloth dampened with antistatic film cleaner or tack cloth
to remove dust and dirt from the coversheet. Wipe the vinyl coversheet in one
direction as it is unrolled. The vacuum coversheet must be kept static free, clean,
and free from mechanical damage (holes, etc.)
8. Rub the vinyl coversheet lightly but firmly with your hands, cardboard or a
Toray Stick (see Platemaking Supply List) to eliminate any bubbles or wrinkles.
If you see any dirt in the image areas, be sure to roll back the coversheet and
remove it before proceeding with your exposure. It is important to keep the
Section 4‐5 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
vacuum gauge at .8 bars, 25 inches of Mercury or higher, or .99 on the ECLF
without fluctuation during exposure.
7. Proceed with main exposure. For dual bank exposure units, back exposure and
main exposure is performed simultaneously.
Main Exposure for Digital Plates :
1. For single bank exposure units, place the raw, laser‐ablated plate on the exposure
unit facing upward.
2. When using a glass bed exposure unit (dual bank), place masking material to
cover all exposed glass so that UV light will not be reflected from the upper bulb
bed.
3. Proceed with main exposure. For dual bank exposure units, back exposure and
main exposure is performed simultaneously.
Section 4‐5 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Cyrel®FAST Plate Post Exposure and Light Finishing
Step 4: Post Exposure
The plate surface is exposed with
UV-A radiation.
Step 5: Light Finishing
The plate surface is exposed with
UV-C radiation.
Post Exposure
Post exposure is necessary to ensure that the plate reaches its final hardness and
durability. However, not all plates require this additional UV cure to complete the
polymerization process. Over‐curing can result in brittle dots and fine lines. Post
Exposure uses the same type of UV‐A light that is used for back and main exposure.
The effectiveness of the post exposure procedure depends on the UV output of the
exposure bulbs. Post exposure can be carried out simultaneously with light finishing
Effects of Post Exposure
Plate achieves its final overall hardness
Completes polymerization
Section 4‐6 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Safety Information ‐ WARNING: Potential Physical Hazard—Radiation
Exposure Units
UV‐A Light Source Used during Post Exposure (350‐400 nm)
UV‐C Light Source Used during Light Finishing (Short Wavelength 254 nm)
Recommended PPE:
Never look directly at the lighted UV bulbs. If necessary, during maintenance, a
welding face shield with a shade 6 is recommended.
Wear long‐ sleeve shirt and leather gloves
Ultraviolet Light Safety Information:
Do not defeat or bypass built‐in equipment safety features.
Do not operate lamps with covers removed.
Do not stare directly at the UV bulbs.
Do not operate equipment with covers or access panels removed.
All personnel operating and maintaining the equipment should be thoroughly
aware of the hazards and use appropriate personal protective equipment.
Refer to manufacturer’s equipment manual for safety requirements when viewing
UV light through viewing slots.
Light Finishing
After processing, the surface of a Cyrel® plate is slightly tacky. Light finishing
eliminates surface tackiness of Cyrel® photopolymer plates, and the plate’s final
surface properties are achieved. The light finishing step utilizes short wavelength (UV‐
C) radiation.
• Removes surface tackiness
• Increases the durability and storability of a plate
• Solvent and ozone resistance is increased
Section 4‐6 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Most light finishers today combine the UVA post exposure and the UVC light finishing
exposure in one unit. Both the post exposure and light finishing steps are performed
simultaneously. When using two separate exposure units, always perform the post
exposure step first. The surface of the plate may still have a few microns of partially
cross‐linked material on the surface making it tacky. The light finishing step increases
the cross‐linking density of the surface.
Light Finishing Step Test
Light finishing time depends on
UV Output
Temperature
Equipment Exhaust Rate
. Plate Type
Because of these variables, a light finishing step test (see procedure below)
should be performed to determine the correct finishing time for Cyrel®
photopolymer plates. Any imaged, processed (and dry) Cyrel® plate can be used for
this test. A back exposure step test plate is ideal for this test, since it has already been
divided into sections. If you are not using the a back exposure step test plate, mark
off as many equal sections as needed on processed plate to accommodate the range
of recommended times (refer to plate processing guidelines) necessary to complete
the test. Actual times may vary slightly from these values due to variations in light
finishing equipment, design for different size units, and/or different manufacturers
(i.e., lamp intensity, lamp spacing, and lamp height).
Allow the plate to cool to room temperature after drying or thermal processing, and
then finish each step in two‐minute intervals using opaque material to cover the
sections you are not exposing. The plate is properly finished when it is no longer
tacky. One quick method to determine when a plate is adequately detacked, is to
utilize the coversheet material that is removed from the raw material. Place the
coversheet on the finished step test plate, pressing it down with your fingers. Slowly
lift the coversheet from the plate. Take note at what finishing time the coversheet no
longer sticks to the plate.
Section 4‐6 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
For maximum printing performance/durability, a minimum light finishing exposure
to just remove plate tackiness is recommended. Prolonged exposure (“over‐
finishing”) can lead to poor ink transfer and/or increased cracking potential
immediately or subsequently during use/storage.
Post Exposure and Light Finishing Procedure
1. Make sure there are no spots of any kind, dirt, etc. on the plate surface.
2. For solvent plates, make sure the plate is completely dried and cooled to room
temperature.
3. Place the plate on the exposure unit bed face up.
4. Expose the plate. Post exposure and light finishing can be run simultaneously with
the appropriate equipment. If each operation is run separately, the post exposure
step should be performed first.
Cleaning Polyester Support after Finishing
Polymer residue must be removed from the back of the plate so that it does not
interfere with plate thickness uniformity or adhesion of the mounting tape in printing
applications. Place the plate on a clean surface and wipe the polyester back to
remove. An antistatic film cleaner or alcohol can be used; however, large amounts
should not come in contact with the surface of the plate.
Section 4‐6 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
The DuPont™ Cyrel®FAST Thermal Platemaking System
The Cyrel®FAST Platemaking system is the world’s first dry, thermal technology that
allows the development of analog and digital flexographic plates without using
solvent. The thermal developing of the Cyrel®FAST plate accelerates the platemaking
process to produce a high‐quality plate in one hour or less by eliminating solvent
processing and the drying step. This system eliminates the use of solvents or aqueous
washout solutions from the plateroom, along with recycling and storage concerns.
The unpolymerized polymer collected in the thermal system is accumulated on a
nonwoven fabric, making disposal simple and safe.
The Cyrel®FAST Thermal Platemaking Systems includes:
1. DuPont™ Cyrel® EC/LF (Exposure, Light Finisher,
Post Exposure)
2. Cyrel®FAST photopolymer plates
3. Cyrel®FAST thermal processor
4. DuPont™ Developer Roll
Cyrel®FAST Platemaking
The Cyrel®FAST plates can be imaged using conventional film negative (analog), or
laser‐ablated plate (digital). The plates are given a back and main exposure in the
same manner as conventional photopolymer plates.
After main exposure the plate is clamped in the
Infrared Cyrel® FAST processing unit on a drum that
Heating passes an infrared heating section as it turns.
During the development process, the plate is
heated to the melt flow index of the
Nonwoven photopolymer. It is then pressed gently against
Plate Fabric a nonwoven fabric, which absorbs the
Drum unexposed, molten photopolymer, leaving a
clean printing surface. Standard processing
programs are already loaded in the machine
when installed. No drying step is required after
thermal development.
Section 5‐1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
The Cyrel®FAST plate is post‐exposed and light finished and ready for press.
Some of the Cyrel®FAST system advantages and benefits are:
• Easy to operate – quickly making plates
• Simple installation of equipment
• Improved Sustainability – elimination of all organic solvents
• Very short access time to finished plate – higher throughput,
no need for back‐up plates.
• Superior print quality on all substrates
DuPont™ Cyrel®FAST Thermal Platemaking Equipment Portfolio
The DuPont Cyrel®FAST System is a revolutionary technology that offers enhanced
pressroom productivity. Cyrel®FAST uses a dry, thermal technology for plate
development, completely eliminating conventional solvents and aqueous washout
solutions. In addition to the obvious environmental and health gain, it also reduces
the plate processing times significantly (up to 70%).
Additional information and brochures for the Cyrel®FAST thermal platemaking
equipment can be found by region on the main Cyrel® internet website,
www.cyrel.com.
DuPont™ Cyrel®FAST Analog and Digital Plate Portfolio
Cyrel®FAST is an innovative, highly productive plate processing technology utilizing
solvent‐free thermal processing. It produces a press‐ready, finished plate in an hour
or less. Digital Cyrel®FAST plates give the ultimate in print quality with wide tonal
range from highlights to detailed shadows.
DuPont’s portfolio of digital and analog Cyrel®FAST plates meets the needs of a
broad range of printing applications. Information and brochures for Cyrel® printing
plate products can be found by region on the main Cyrel® website, www.cyrel.com.
Section 5‐1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Cyrel®FAST Platemaking Process
Overview
Cyrel®FAST plates are produced in five
basic steps:
1. Back Exposure 3. Processing
Back exposure sensitizes the plate, Unexposed photopolymer is removed in the
establishes the plate relief, improves thermal processor by heat transfer. The molten
adhesion between the polyester support polymer is absorbed by a nonwoven fabric. . No
and the photopolymer, and provides a firm solvents are used.
base for fine lines and screens. It is an
exposure of the back of the plate through
the polyester base. The back exposure time
is determined by a back exposure step test.
UVA Exposure Relief
Floor
4. Post Exposure
Floor Building up
Post exposure completes the polymerization
Photopolymer process, and the plate achieves its final hardness.
Polyester Support UVA Exposure
2. Main Exposure
Main exposure is carried out through a film
negative or laser‐ablated plate. The
exposed photopolymer cannot be removed
in the processing step, thus creating the
relief image. Because the image is formed
by exposure, the plate can reproduce the 5. Light Finishing
finest details of the original film negative or Light finishing removes the surface tackiness,
electronic file. increases durability, and resistance to solvents
and ozone. Light finishing and post exposure
UVA Exposure can be performed simultaneously.
Short Wavelength UVC Exposure
Crosslinked Photopolymer
Negative or Lams Layer
Polyester Support
Section 5-2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
The Cyrel® Digital Workflow
The Cyrel® Digital Workflow System features the Cyrel® Digital Imager (CDI)
combined with a choice of several Cyrel® digital plate types, and processed in
either Cyrel® solvent or Cyrel®FAST thermal processors. This Cyrel® computer‐
to‐plate process widely known and used in flexo platemaking today utilizes a
proprietary black mask layer bonded directly to the photopolymer layer during
plate manufacturing. This laser‐imaged mask is referred to as the LAMS layer
(Laser Ablation Mask System).
Benefits of Cyrel ® Digital Imaging
Unsurpassed quality and consistency are achieved with Digital technology. It affords
the capability of handling complex or unique packaging jobs with reduced production
time.
The Cyrel® Digital Imager creates an accurate, high‐resolution image in the thin
LAMS layer. Image features created in the LAMS layer are defined by the spot size
of the laser, meaning that very fine detail can be resolved.
Cyrel® digital plates require no film layers and no vacuum drawdown. The virtual
absence of light scatter means that the high‐resolution image in the mask layer is
predictable in the photopolymer. Additionally, the possibility of out‐of‐contact
spots or dirt imaging between the negative and the polymer with conventional
plates is eliminated. The presence of oxygen during the UV exposure creates
sharpened plate features that improve print quality for line work, text, fine
highlights, and throughout the tone scale.
Analog Dot Digital Dot
Conventional Dots Digital Dots
Section 6‐1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
The Cyrel® Digital Workflow
The Cyrel® Digital Workflow employs these key elements.
• Cyrel® digital photopolymer plates
• The Cyrel® Digital Imager (CDI) plate‐setter to laser‐ablate the
mask on the plate
• The Cyrel® FAST UV Exposure Unit or other Cyrel® Exposure
Unit to expose the plate with UV light;
• The Cyrel® FAST Thermal Developer or a Cyrel® Solvent
Processor to remove the unpolymerized monomer to create the
relief plate.
Laser imaging
The Cyrel® Digital Imager (CDI) is manufactured by EskoArtwork. A CDI is an
external drum write engine (plate‐setter) that uses an infrared laser to write an
image into the LAMS layer.
Laser
Controlled by the computer, the laser in the CDI burns away (“ablates”) the LAMS
layer but has no effect on the photopolymer layer below it, creating a photopolymer
plate with an integral mask.
UV Exposure
Back exposure of the plate is completed before laser imaging. Main Exposure is
performed after laser imaging. The Cyrel® digital plate is taken off the CDI and
placed in a conventional exposure unit for the main UV exposure. The integral
mask serves as the platemaking film, but since it is built into the plate, there is no
need for vacuum drawdown to ensure good contact. Variability and out‐of‐contact
spots are eliminated, giving a consistent top‐quality photopolymer plate.
Section 6‐1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Process
After UV exposure, the Cyrel® digital plate goes through a Cyrel®FAST thermal
processor or solvent processor. The LAMS mask layer is removed along with the
unexposed monomer. The result is a relief photopolymer printing plate with
extraordinarily sharp dots.
Depending on your development system, the digital plate is completed through
the remaining conventional platemaking steps (drying for solvent plates), post
exposure and light finishing.
See the section on Cyrel® Platemaking – All Systems for more information on
the steps for producing Cyrel® photopolymer plates.
Section 6‐1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Cyrel® Digital Platemaking Instructions
Pre‐Press
All 1 Bit Tiff or .Len files should have
bump curves calibrated for the specific
digital‐imaging device and plate type to
be used. This is done in pre‐press when
the file is ripped. The procedure for
determining the correct bump curve can
be found in a separate file in the digital
section of the manual.
Digital plates should have a highlight
bump curve large enough to reproduce
a minimum finished plate mask opening
that provides a uniform dot size and uniform
thickness throughout the tonal range for the
screen ruling in place. A finished plate dot
value smaller than the mask opening can
lead can lead to poor image transfer, premature
plate wear or dirty printing.
Prior to imaging, examine the 1‐Bit Tiff
or .Len files using an application such as
ShowCT, Dot Spy, TIFF viewer, etc.
Inspect to ensure correct minimum dot
size and correct screen ruling, dot shape
and angle, as well as an overall inspection
to ensure correct content, color separation, etc.
Section 6‐2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Add a control target, such as the DFTA CtP
(minimum version V1.2) target shown below
to the side of each full size digital plate file.
This can be used later for checking stain level
and dot quality. Contact your Cyrel® Technical
Representative
Platemaking
Digital plate processing guidelines can be
Obtained from your Cyrel® representative
and information on procedures for
optimum exposure time testing can be found
in the “Cyrel® Platemaking – All Systems”
section of this manual.
Back expose the plate the required time
that you have determined from your Back
Exposure Step Test. Recommended relief
for Cyrel® plates can be found in the General
Platemaking section.
Ablate the plate with image and control
target.
After ablating the plate, using tape,
pull an unimaged area of the mask from
the plate. Zero the densitometer to this
clear polymer area. Then read a 100%
solid ablated area on the quality control
target. It is critical that the 100% reading
Section 6‐2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
be between 0.02‐0.07. This reading is the
“stain level.” If the stain level is higher than
0.07, increase the amount of laser energy
to the plate until your stain level is below
0.07. If your stain level is too high, check
your focus and laser energy.
Next, again zero the densitometer on the 100%
solid ablated area on the control strip and
read the 50% value on the control strip.
The densitometer reading should be between
0.29 and 0.31 (preferred value is .030.).
This is the original density for a 50% dot.
If reading is below 0.29 or above 0.31, check
the laser energy of the CDI. Newer software
versions set the energy directly and correct
the laser power and speed themselves.
For example, if the 50% reads a low density
(example .026), increase RPMs
or lower laser power (watts).
Based on your Main Exposure Step Test,
determine the minimum amount of time
to hold a uniform highlight dot.
Main expose the plate. Use only a
conventional exposure unit with a bank
of UV exposure bulbs. Do not use point
or capillary light sources, as these light
exposure units do not reproduce quality plates.
Section 6‐2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Solvent or thermally process the
plate for the required amount of time for
plate thickness. Thermal Processed
For solvent‐processed plates:
Dry the plate for about 20 minutes in a
forced air oven at 140 deg. F. After 20
minutes, check each plate for solvent
spots. If solvent spots are detected,
remove the plate from the dryer or shut
the dryer off and wipe the plate with
antistatic film cleaner or an alternative Solvent-Processed
compatible solution. If no solvent spots,
are visible, continue to dry the plate for
the required amount of time established
by a drydown test. Plates should be dried
at 140 degrees F/60°C. until they reach a
uniform thickness. Keep in mind that the
highlight dots are the last to revert back
to their original thickness.
After drying, post expose and light finish
the dried plate for the required amount of
time. Always post expose two minutes less
than the light finishing time. Do not use
excessive post exposure times, as prolonged
post exposure can lead to fractured dots,
premature plate wear, or dirty printing.
A Light Finishing Step Test should be
performed for each plate type.
Certain plate types require less or no
post exposure.
Section 6‐2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Establish a procedure to verify the
consistency of your finished plate. Refer
to the DFTA CtP (minimum version V1.2)
target procedure or ask your Cyrel®
Technical Representative.
Use the Cyrel® Quality Control Checklist to
examine your finished plate (available in the
Quality Control Section of this manual).
The plate should then be trimmed with a
beveled edge and packaged appropriately
for shipment.
Section 6‐2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Determining the Bump Curve for Digital Plates
This procedure is to determine the minimum stable highlight dot on a digital plate. It is
often used to:
1) determine the proper bump‐up curve to be used at the RIP
in digital platemaking, and
2) as a consistency check in the digital plate making process.
All other aspects of platemaking must be controlled for a valid measurement or
comparison: plate type, plate thickness, main exposure, back exposure, relief, and
processing (solvent or FAST),
Target
A highlight dot target is used to find the minimum stable dot. The accuracy to which the
minimum stable dot can be established will depend on the gray scale resolution of the
target. All steps in the prepress, imaging, and platemaking process can have an affect on
the tonal value of the minimum stable dot.
The highlight dot target should contain highlight tone values +/‐ 3% of the expected
minimum stable dot value. Adjacent tone areas should have steps of at least 0.5%,
preferably 0.39% (1/256). A good all‐purpose scale would cover 0 – 10% in steps of 0.5%
or less.
The file is ripped with linear values, and imaged in perfect focus with the proper energy
to insure the mask has been cleared to the acceptable range (.03‐.07 density). The plate is
then processed according to the normal workflow that you would follow.
Processed Plate Measurement
Examine the plate by turning it upside‐down on a light table, so that the tops of the dots
are touching the surface of the light table. It must be a standard diffuse‐illumination
graphic arts light table.
Use a 50X – 100X (preferably 100X) microscope to examine the tops of the dots through
the base of the plate. The tops of stable dots will contact the surface of the light table and
can be observed through the microscope as a bright dot circle, surrounded by the dot
base. See Figure 1 below.
Section 6‐3 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
dot base structure
Figure 1
dot circles -- tops
of dots in contact
with light table
The size of the dot circles will increase and decrease with the tonal values in the scale. At
small tonal values the dots are unstable. These unstable dots will have poorly formed or
inconsistent dot circles, and inconsistent dot bases (see figure 2). The smallest tonal area
that has both open and consistent dot circles and consistent dot bases is the minimum
stable dot (as shown in Figure 1). Of course, determining the smallest, consistent dot size
is a somewhat subjective determination. For press latitude, some customers may require
(and choose) a larger minimum stable dot than others.
Poor Choice Better Choice
inconsistent dot bases
increasing exposure
tonal value
Figure 2
poorly formed consistent dot bases
and inconsistent and
dot circles consistent dot circles
MINIMUM STABLE DOT
Section 6‐3 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
The digital process has the capability to create dots too small for the flexographic process.
The smallest imaged dot is usually below the surface of the other features on the plate.
This will commonly result in dirty printing. The smallest dot on the plate is not the best
dot on the plate. Once again, the smallest, consistent dot is the better choice.
Section 6‐3 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Cyrel® Solvent Platemaking System
DuPont™ Cyrel® solvent platemaking systems serve the broadest range of applications.
High resolution dot, excellent line definition, deep reverses and clean floors are
achieved to meet the highest flexographic standards.
Cyrel® offers a range of solvent‐processed printing plates and platemaking equipment
configurations to address customer size requirements. The DuPont™ Cyrel® In‐Line
Platemaking Systems are high‐capacity, fully‐enclosed processing units for
automatically producing high quality Cyrel® photopolymer printing plates in a safe
and clean environment.
The Cyrel® Solvent Platemaking System includes:
1. Cyrel® Exposure Unit
2. Cyrel® Solvent Processor
3. Cyrel® Dryer
4. Cyrel® Post Exposure/Light Finishing Unit
5. Cyrel® Solvent‐Processed Photopolymer Plates
Cyrel® Solvent Platemaking Equipment
Cyrel® offers a range of solvent‐processed platemaking equipment configurations to
address customer size and productivity requirements. The DuPont™ Cyrel® In‐Line
Platemaking Systems are high‐capacity, fully‐enclosed processing units for
automatically producing high quality Cyrel® photopolymer printing plates in a safe
and clean environment.
Additional information and brochures for Cyrel® solvent platemaking equipment can
be found by region on the main Cyrel® internet website, www.cyrel.com.
Cyrel® Analog & Digital Solvent Plate Portfolio
DuPont offers a variety of digital and analog solvent‐processed plates that meet the
needs of a broad range of printing applications. These applications include: flexible
packaging, tag & label, folding carton, beverage carton, corrugated board, offset
varnishing and metallic inks. DuPont’s portfolio of Cyrel® digital and analog solvent‐
processed plates meets the needs of a broad range of printing applications. Additional
information and brochures for Cyrel® printing plate products can be found by region
on the main Cyrel® website, www.cyrel.com.
Section 7‐1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Cyrel® Platemaking Overview for Solvent‐Processed Plates
Cyrel® Solvent plates are produced in six basic steps:
1. Back Exposure 3. Processing
Back exposure sensitizes the plate, Unexposed photopolymer is removed in the
establishes the plate relief, improves processor to produce a relief printing plate. A
adhesion between the polyester support processing solution and brushing action are
and the photopolymer, and provides a firm used to dissolve and remove the unexposed
base for fine lines and screens. BX helps photopolymer.
produce a proper dot profile in conjunction
with proper main exposure. It is an
exposure of the back of the plate through
the polyester base. The back exposure time Relief
is determined by a back exposure step test. F
Floor
UVA Exposure
4. Drying
The processed plate swells during washout. The
Floor Building up plate is dried in hot air (60°C / 140 F) to remove
absorbed processing solution.
Photopolymer
Polyester Support
2. Main Exposure
Main exposure is carried out through a film
negative or laser‐ablated plate. A vacuum
coversheet is used during exposure for
5. Post Exposure
analog plates to obtain an tight bond
Post exposure completes the polymerization
between the negative and the plate. With
process, and the plate achieves its final hardness.
digital plates, no vacuum coversheet is
needed during exposure. The physical
UV Exposure
properties of the exposed photopolymer
changes and exposed parts cannot be
UVA Exposure
removed in the processing step, thus
creating the relief image.
UVA Exposure
6. Light Finishing
Light finishing removes the surface tackiness,
increases durability, and resistance to solvents
and ozone. Light finishing and post exposure
can be performed simultaneously.
Crosslinked Photopolymer Short Wavelength UVC Exposure
Negative or LAMS
Polyester Support
Section 7‐2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Processing Solvent Cyrel® Solvent Plates
Step 3: Washout
Unexposed polymer is
removed by brushes
to create a relief
printing plate.
During the washout process, the unexposed, non‐polymerized photopolymer material
is removed to produce a polymerized relief image on the plate. The washout action
begins at the surface of the plate and proceeds gradually downward into the plate
until full relief depth is achieved. The unexposed polymer is removed by the
combined action of brushes and washout solution.
Washout Time
Washout time should be kept to a minimum. The plate swells during the washout
step due to solvent absorption. The swelling increases the longer the plate is in
contact with the solvent. Therefore, if washout time is excessive, additional solvent
is absorbed by the plate requiring longer drying times. Excessive swelling can also
cause damage to the image. Washout time depends on the following parameters:
• Plate formulation
• Processor design
• Brush contact pressure
• Composition of washout solution
• Solids concentration in the washout tank
• Relief depth
• Solvent temperature
DuPont recommends the use of Cyrel® Processing Solution; however, Cyrel®
printing plates can be processed in most industry washout solutions. It is
recommended to optimize washout and drying times when using any washout
solution.
Section 7‐3 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Cyrel® Processing
Washout Temperature
North America
OptiSol® Rotary Room Temperature
OptiSol® Inline 38‐40°C
Cylosol 30°C‐32°C for thin plates (<112 mils)
32°C‐34°C for thick plates (>112 mils)
EMEA
Flexosol® Inline 30‐32°C
Flexosol 2 ® Rotary 30‐32°C
Unisol® Inline Room Temperature
To achieve and maintain all operating temperatures (except room temperature), a
cooling/heating unit is required. In order to obtain uniform, consistent washout
results, it is crucial to maintain a constant washout solution temperature.
In‐Line Processing
The finished plate is punched and placed on the Cyrel® processor pin bar, polyester
support side down. The proper washout time, plate thickness, and relief is already
pre‐set on the control panel as program. The bar is put in place, and the processor
takes the bar, with the plate attached, through the processor. The brush pressure
for the Cyrel® In‐line processor has been pre‐set in the programming.
The procedure for determining correct washout time is the same as described in
the back exposure step test procedure. Therefore, washout time can be
determined at the same time you perform a back exposure step test. Washout time
can also be checked with each plate sent through the processor by following the
same procedure listed below.
Determining Correct Washout Time
1. During the back exposure step test, a strip of high density stripping tape is placed
across the center back of the test strip for solvent plates. This tape blocks the light
to prevent polymerization of the plate material under the tape.
Solvent plate back exposure
Section 7‐3 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
2. Before processing, remove the high density tape. Set the processor to wash out the
number of seconds previously set up when you installed the machine or the
number of seconds you are currently using.
3. After the back exposure step test plate has been processed, measure the over‐scrub
section (produced by the high density tape).
4. If the plate has not been washed down at least 10 mils past the floor for thin plates
(up to 125 mils) or 20 mils for thicker plates, the wash times should be adjusted.
Increase washout time to obtain 10 mils of over‐scrub or more. Decrease washout
time if reverse is deeper than 10 mils for thin plates or 20 mils for thicker plates.
Once the processing and replenishment of the processor is complete, the pin bar or
tape bar will continue to feed through the back end of the processor. Once the
plate finishes processing, it can be inspected and you can continue on to the next
platemaking step. Safety glasses with side shields and appropriate gloves should be worn
when removing plates from the processor.
Rotary Processing
The plate is clamped on the washout drum. The proper washout time and
replenishment rate is set on the control panel. The brush pressure setting should
be correct for each plate thickness. Use the manufacturer’s operating settings for
the plate thickness being processed.
After washout, the plate is rinsed by flooding with clean washout solution
(replenishment cycle). Safety glasses with side shields and appropriate gloves should be
worn when removing plates from the processor.
Blue Towel Procedure (Rotary Processors)
After completion of the washout cycle, while on the washout drum, the surface is
blotted with a DuPont blue, lint‐free towel to remove residual solvent. The dark
side of the blue towel is placed against the plate when blotting. The towel is
patted onto the plate and blotted with a glove‐protected hand. The towel is then
removed and the plate is blotted with a second towel. The plate is removed from
the processor with the second blue towel adhered to the image and placed, face
down, on a flat surface with the blue towel attached to the face of the plate. Wipe
Section 7‐3 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
and dry excess solution from the back of the plate with another blue towel.
Remove the blue towel from the face of the plate and place the plate in the dryer.
This process will eliminate cleaning the back of the plates after finishing and post
exposure. Blue towels can be purchased from your Cyrel® plate supplier.
Solvent Replenishment
During the washout process, washout solvent dissolves the unexposed
photopolymer. As the solvent becomes more saturated with photopolymer, the
washout efficiency decreases. The washout solvent must, therefore, be constantly
renewed. The washout unit contains a replenishment system for this purpose.
Solvent replenishment is determined by the plate area and relief. Proper
replenishment is essential for high quality, consistent platemaking. The
replenishment rate is approximately 1 quart/sq. ft of plate material for a relief of
.025–.030”. The replenishment volumes for thicker plates should be calculated
accordingly.
Section 7‐3 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Drying Cyrel® Solvent Plates
Step 4: Drying
Drying is carried out in a forced
air oven at a temperature of
140°F/ 60°C.
The Cyrel® photopolymer plate absorbs solvent during the washout process, and
the polymerized relief image is soft and swollen. Drying evaporates the solution
so that the plate returns to a uniform thickness.
Drying is carried out in a forced air oven at a temperature of 140F (60°C) +/‐ 5°C.
Dryers must comply with the National Fire Protection Association (NFPA)
standards for combustible solvents. The actual dryer temperature should be
checked periodically in each dryer drawer in nine positions (back, middle, front,
left, right, center) with a thermometer. For suggested thermometers, see the
Platemaking Supplies and Sources List in the Appendix.
To ensure the dimensional integrity of the polyester support and minimize
plate to plate variability, the following procedures should be followed:
1. Do not set the dryer temperature above 140F (60C) or lower than 135F (55°).
Higher temperatures can cause shrinkage of the polyester support, and
lower temperatures can cause longer drying times.
2. Plates should be dried until their thickness no longer shows any significant
changes. A drying test is recommended using your own equipment and
workflow to determine optimum drying times for each plate type.
Insufficient drying time can cause unacceptable thickness tolerances within
the plate. Drying time depends on:
• Processor Type
• Processing Conditions (solvent type,
temperature, and washout time)
• Dryer Exhaust
• Dryer Temperature
Section 7‐4 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Inspect the plates during the drying step. All plates should be carefully removed
from the dryer after 20 minutes, i.e., long enough to evaporate solvent on the
plate surface, so that they can be inspected for image quality and drydown spots.
Drydown spots are created when droplets of processing solution evaporate on the
plate during drying. Drydown spots can be removed by saturating a clean, lint‐free
cloth with anti‐static film cleaner or similar solvent and wiping the area on the
plate in a light, smooth, continuous motion. Do not allow the film cleaner to
puddle on the plate’s surface. Long‐term effects of film cleaner may be detrimental
to the plate. This preliminary inspection also allows you to decide if a remake is
necessary due to any exposure problems, saving production time.
(Note: Read and follow manufacturer’s published guidelines for safe handling of anti‐static
film cleaner.)
Proper drying is especially important for process color work to ensure maximum
resolution and tonal reproduction. Process work may take longer to dry than line
work due to solvent residue sitting in the wells between dots.
After drying, the surface of the plate is tacky. At this stage, the plates should not be
stacked or brought into contact with other materials and surfaces. The printing
surface should not be touched before finishing, since marks will appear on the plate
surface. The finishing process removes this tackiness.
Plates must be completely dried before the finishing step, or thickness uniformity
may be affected. Trapped solution diffuses out of the plate at uneven rates and can
lead to variation in plate thickness.
Section 7‐4 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Cyrel® Cylosol Processing Solution‐NA
Cyrel® Cylosol is the latest development by DuPont in flexographic plate washout
solvent technology for both rotary and inline processors. Cylosol has an especially
mild odor and clean scent during processing and drying. It can be efficiently
recovered in existing distillation units and requires no re‐balancing after distillation.
Cylosol’s 55‐gallon open‐head drum put‐up is part of DuPont’s efforts for waste
minimization. The empty open‐head drum can be recycled and used as a
container for the distillation stillbottoms. There are two added values to the
customer for using the open‐head drum. The customer has fewer empty drums
to dispose of and fewer drums to buy because he can reuse the drums to
package solvent‐related wastes.
Safety
DuPont Processing solutions fall under the definition of “hazardous as a chemical
hazard” as defined under OSHA’s Hazard Communication Standard. DuPont
processing solution can be used safely when used as directed, and when applicable
safety precautions are followed. Cylosol is classified as a Class IIIA combustible
liquid and has a flashpoint of about 144F/62.2C. Safety considerations can be
found in the Material Safety Data Sheet and also in the Safety & Environmental
Section of this Manual.
Storage
Cyrel® processing solutions must be protected from frost during storage. The
solution should be brought to room temperature before use.
Cylosol Distillation
The unexposed portion of the photopolymer plate dissolves in the washout solution to
produce a relief image. The solution must then be reclaimed by distillation. DuPont
washout solution can be distilled without any problems in most commercially
available vacuum‐based distilling units. If in‐house distillation is not available, choose
a qualified and reliable solvent reclaimer who will return clean, uncontaminated
solution.
Section 8‐1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Cylosol Distillation Conditions
The distillation of Cylosol is performed in a vacuum at 0.914 bar/27”Hg/13.3 psi. The
following data refers to the PRI Distillation unit.
Oil temperature 175°C/345°F
Oil limit temperature* 197°C/244°F
Vapor limit temperature* 154°C/ 309°F
Boiling Temperature 118‐127°C/244°‐261°F
*temperature at which the still automatically shuts
down
Add‐backs
Cylosol washout solution composition varies very little in specific gravity, and no add‐
back has been needed.
Loss of Washout Solution (Emissions)
Stack monitoring at the customer plant site for actual measurements of VOC emissions
can provide the best accuracy for estimating VOC emissions. However, emissions can
also be estimated by using ʺmass balanceʺ over a realistic time frame, such as a year.
You must keep supporting records of your solvent purchases and/or use when
utilizing this method. Emissions are estimated by difference. This method provides a
reasonable degree of accuracy and is an accepted compliance approach in many parts
of environmental regulations.
When using ʺmass balance,ʺ you are estimating the emissions that went up the stack by
determining the number of gallons of solvent added back to the platemaking system
during a year to compensate for what was lost during processing and drying. You
must then subtract the number of gallons of solvent that was lost in other ways, such
as, pumped out with the stillbottoms or lost from any other disposal method. Contact
your Cyrel® Account Representative for more information on estimating VOC’s.
Section 8‐1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
OptiSol® Solutions -NA
OptiSol®, developed in 1989, was the first alternative washout solution produced by
DuPont for use in rotary and inline processors.
OptiSol® is available in 30 and 55‐gallon putups. OptiSol®’s 55‐gallon open‐head
drum put‐up is part of DuPont’s efforts for waste minimization. The empty open‐
head drum can be recycled and used as a container for the distillation stillbottoms.
There are two added values to the customer for using the open‐head drum. The
customer has fewer empty drums to dispose of and fewer drums to buy because he
can reuse the drums to package solvent‐related wastes.
Safety
DuPont Processing solutions fall under the definition of “hazardous as a chemical
hazard” as defined under OSHA’s Hazard Communication Standard. DuPont
processing solution can be used safely when used as directed, and when applicable
safety precautions are followed. OptiSol® is classified as a Class IIIA combustible liquid
and has a flashpoint of about 154F/68C for inline solution and 194F/90C for rotary.
Safety considerations can be found in the Material Safety Data Sheet and also in the
Safety & Environmental Section of this Manual.
Storage
Cyrel® processing solutions must be protected from frost during storage. The solution
should be brought to room temperature before use.
OptiSol® Solution Maintenance
The unexposed portion of the photopolymer plate dissolves in the washout solution to
produce a relief image. The solution must then be reclaimed by distillation. OptiSol®
washout solution can be distilled without any problems in most commercially available
vacuum‐based distilling units. Please consult the manufacturer of your distillation unit for
specific instructions on safely operating the equipment. If in‐house distillation is not
available, choose a qualified and reliable, solvent reclaimer who will return clean,
uncontaminated solution.
Section 8‐2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
OptiSol® Inline Distillation Conditions
The distillation of OptiSol® is performed in a vacuum. In general, the following conditions
are suggested for distilling OptiSol® inline solution, and this refers to the PRI Distillation
unit.
Oil temperature 325F
Oil limit temperature* 385F
Vapor limit temperature* 310F
*temperature at which the still automatically shuts
down
OptiSol® Inline Re‐Balancing
We recommend that you measure the specific gravity of the distillate on a regular basis to
confirm that the blend falls within our recommended range. The hydrometer’s
measurement range must include the OptiSol® range listed below. Remaining within the
limits specified below will ensure that the washout is adequate to remove all unexposed
monomer prior to the plate entering the clean‐up section of the processor.
Specific gravity must be measured @20°C/68°F. The limits range from 0.8573‐0.8554.
Section 8‐2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Procedure for Checking and Re‐Balancing OptiSol® InLine
Reminder: Use proper Safety equipment when working with solvents.
A. Taking Samples
Samples of OptiSol® should be taken after every cook down for testing.
(See your distillation unit manual for how to take a sample. Take sample from clean side of
unit after mixing for 1‐2 minutes.
• Make sure OptiSol® is clear with no solid particles.
• Make sure graduated cylinder and hydrometer are clean. If not, rinse with virgin
OptiSol®.
• Hydrometer is fragile. Handle with care.
B. Determining % Acetate of OptiSol® in System
1. Transfer sample into supplied graduated cylinder.
2. Use hydrometer to take Specific Gravity reading. See attached procedure, “Reading
Specific Gravity with a Hydrometer”
3. Record the hydrometer reading to four places after the decimal. This is the Specific
Gravity of OptiSol®
• The fourth decimal place should be a zero or five.
4. Take temperature of OptiSol® immediately following the hydrometer reading and
record.
5. Find the % Acetate on Chart #1 by using the Specific Gravity and Temperature
information.
6. After determining % Acetate, you need to determine if you need to add back
OptiClean (acetate).
7. If you are at 70% or higher, do not add any OptiClean.
8. If you are lower than 70%, use Chart #2 to determine add‐back of OptiClean. Follow
direction below for adding OptiClean to your system
C. Adding OptiClean to System
• Do not add more OptiClean than you need.
If your % Acetate is 66% or higher then follow the Maintenance Mode. If your % Acetate
is 65% or lower, then follow the Rebalancing Mode.
D. Maintenance Mode
9. Determine the amount of OptiSol® in gallons that is in the Clean Tank.
10. Using Chart #2, determine how many gallons of OptiClean are needed to get the
Clean Side Tank back to 70% acetate.
Section 8‐2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
11. Add OptiClean to Clean Side Tank before adding virgin OptiSol® to top off system, if
needed.
E. Rebalancing Mode
12. Determine the amount of OptiSol® in gallons that is in the Clean Tank.
13. Using Chart #2, determine how many gallons of OptiClean are needed to get the
Clean Side Tank back to 70%.
14. Add OptiClean to Clean Side Tank and mix.
15. Drain the plate processor tank and replenish with the balanced OptiSol® from the
Clean Side Tank.
16. Distill over OptiSol® from Dirty Side Tank and measure OptiSol® for % Acetate
using hydrometer.
17. Determine the amount of OptiSol® in gallons that is in the Clean Tank.
18. Using Chart #2, determine how many gallons of OptiClean are needed to get the
Clean Side Tank back to 70% acetate.
19. Add OptiClean to Clean Side Tank. Wait for next cook down and measure %
Acetate to determine which Mode to follow.
Addback Charts Re‐Balancing OptiSol® Inline
Charts for determining the % acetate in distilled solvent and the amount of addback
needed for rebalancing can be found in the following section of this manual.
OptiSol®Rotary
Always be sure to check the specific gravity of your recovered solution prior to use in
the processor. The recommended specific gravity range is 0.922–0.928. The use of
washout solution with a specific gravity outside of this range will affect the washout
rate and plate quality. Check the specific gravity by measuring with a hydro‐meter that
has a specific gravity range of 0.9–1.0.
1. Make sure the distillate drum solution is as close as possible to the calibration
temperature of the hydrometer. (Specific gravity varies with temperature.)
2. Measure the height of the distillate in the drum with a meter stick.
3. Collect a sample into a tall glass container, or graduated cylinder.
4. Measure the specific gravity by suspending the hydrometer in the solution. (Be
sure that the hydro‐meter floats in the solution and is not resting on the bottom or
against the side of the container. Once the hydrometer is motionless, a reading can
Section 8‐2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
be taken.)
5. Determine the appropriate formula to use, if the specific gravity is outside the
acceptable range of 0.922–0.928.
6. Determine the quantity (in gallons) of OptiSol® make‐up solution or Benzyl
Alcohol needed.
7. Add the calculated quantity to the drum.
If the distillate specific gravity is greater than 0.928, OptiSol® Rotary Make‐up Solution
must be added. The number of gallons needed is calculated by:
Gals. of OptiSol® # Gals. Distillate
Rotary Make Up = Distillate X Specific Gravity‐‐ 0.928 divided by 0.058
Solution
Sample:
Distillate in 55‐gallon drum
Distillate height in drum = 20 inches
Specific gravity of distillate = 0.93 8
Using the table* for a 55‐gallon drum, a liquid height of 20 inches = 34.4 gallons.
Calculation:
Make‐up solution needed = 34.4 X (0.938 – 0.928)
0.058
Make‐up solution needed = 34.4 X 0.01 / 0.058
Make‐up solution needed = 5.9 gals.
If the distillate specific gravity is less than 0.922, Benzyl Alcohol must be added. The
number of gallons needed is calculated by:
Gallons of Benzyl Alcohol = # Gallons Distillate X 0.922 – Distillate Specific Gravity
divided by 0.120
Sample:
Distillate in 55‐gallon drum
Distillate height in drum = 30 inches
Specific gravity of distillate = 0.915
Using the table* for a 55‐gallon drum, a liquid height of 30 inches = 51.6 gallons
*The table for height/volume calculations can be found in another file in this section.
Section 8‐2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Calculation:
Make‐up solution needed = 51.6 X (0.922 – 0.915)
0.0120
Make‐up solution needed = 51.6 X 0.007 / 0.120
Make‐up solution needed = 3.01 gals.
Loss of Washout Solution (Emissions)
Stack monitoring at the customer plant site for actual measurements of VOC emissions can
provide the best accuracy for estimating VOC emissions. However, emissions can also be
estimated by using ʺmass balanceʺ over a realistic time frame, such as a year. You must
keep supporting records of your solvent purchases and/or use when utilizing this method.
Emissions are estimated by difference. This method provides a reasonable degree of
accuracy and is an accepted compliance approach in many parts of environmental
regulations.
When using ʺmass balanceʺ, you are estimating the emissions that went up the stack by
determining the number of gallons of solvent added back to the platemaking system during
a year to compensate for what was lost during processing and drying. You must then
subtract the number of gallons of solvent that was lost in other ways, such as, pumped out
with the stillbottoms or lost from any other disposal method.
The ʺmass balanceʺ formula below is provided by DuPont to assist Cyrel® customers in the
analysis of their site compliance with national, state or local regulations and laws for VOC
emissions of our processing solvents.
Total VOC emissions (lbs. /yr.) =
(Gallons of OptiSol® added to system ‐ gallons OptiSol® lost
in the stillbottoms ‐ other OptiSol® losses) X
7.1 lbs. /gal. (OptiSol® Inline)
7.7 lbs. /gal. (OptiSol® Rotary)
Section 8‐2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Alternative Processing Solutions – EMEA
® ® ®
EMEA offers 3 alternative solvents – FlexoSol , FlexoSol‐2 and UniSol .
®
The FlexoSol basic concept was developed in in 1993. FlexoSol has an especially
mild odor and can be used in all Cyrel® inline processors.
Advantages to FlexoSol®
• flash point of 56°C
• lower smell
• more stabile during distillation because of tighter boiling range
It is an alternative solvent to OptiSol ® with low solvent smell.
FlexoSol ® can be used in all inline processors.
It is available in 200 liter drums.
Processing temperature is 30‐34°C. A corresponding heating/cooling unit is needed.
FlexoSol‐2® is a revised formulation of FlexoSol®, developed in 2004.
The optimized composition eliminates the wrinkle swelling during the washout process
and prevents orange peel. FlexoSol‐2® is convenient for In the Round (ITR)‐processors.
Intermediate drying and rewash of the plates is not necessary. FlexoSol‐2® of course is
applicable for all flat processors too.
UniSol® is an alternative solvent for non‐heated processors with short processing
times, but slightly longer drying time. It can be used at room temperature for inline and
rotary equipments without heating units.
Safety
DuPont Processing solutions fall under the definition of “hazardous as a chemical
hazard” as defined under OSHA’s Hazard Communication Standard. DuPont
processing solution can be used safely when used as directed, and when applicable
safety precautions are followed. FlexoSol® and FlexoSol‐2® and UniSol® are classified as
a Class IIIA combustible liquid. Safety considerations can be found in the Material
Safety Data Sheet and also in the Safety & Environmental Section of this Manual.
Section 8‐3 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Safety and product specific data:
FLEXOSOL® FlexoSol-2® UNISOL®
BOILING POINT (°C) 180-215 175-220 175-215
FLASH POINT (°C) 56 61 63
VBF A III A III A III
AUTO IGN. TEMP. (°C) 230 445
FLAMMABLE LIMITS IN 1,0-6,1 1,1-6,5
AIR (VOL %)
GRAVITY (g/cm³) 0,85 0,83 0,91
TA-LUFT (CATEG.) III III III
MASS STREAM (LIMIT) 3 Kg/h 3 Kg/h 3 Kg/h
EXHAUSTED AIR CON- < 3 Kg/h < 3 Kg/h < 3 Kg/h
CENTRATION (LIMITS) NO LIMIT NO LIMIT NO LIMIT
SMELL low moderate moderate
PROCESSING 30 30 20-25
TEMPERATURE
WATER POLLUTION 1 2
GROUP
REGULATORY INFO Xn o
SYMBOL
** At 34°C solvent temperature
*** At 22°C solvent temperature
O not required
Storage
Cyrel® processing solutions and its distillates must be protected from frost during storage.
The solution should be brought to room temperature before use. For transporting special
safety guidelines have to be considered.
Use collecting trays according sized made from steel plate.
Section 8‐3 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
® ®
FlexoSol and UniSol Solutions Maintenance
The unexposed portion of the photopolymer plate dissolves in the washout solution to
produce a relief image. The loaded solution must then be reclaimed by distillation.
®
FlexoSol® and UniSol washout solutions can be distilled without any problems in most
commercially available vacuum‐based distilling units, e.g. Renzmann. Please consult the
manufacturer of your distillation unit for specific instructions on safely operating the
equipment. If in‐house distillation is not available, DuPont offers also finished solvents for
delivery.
For more detailed information for FlexoSol®, FlexoSol‐2®, UniSol®
alternative solutions please refer to the solvent manual EMEA.
Section 8‐3 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Handling, Storing, and Cutting of Cyrel® Raw Plates
Storage Life
If stored properly, Cyrel® raw material has a storage life of up to 36 months. Exposure
and processing of plates over 36 months should be avoided; however, customers often
use them for longer periods of time when recommended storage and handling
practices are followed. Ideally, plates should not be exposed until the “use after” date
on the plate box label. If plates are used before the “use after” date, back exposure and
main exposure step tests must be performed. See Packaging Section to determine
location of “use after” date on the plate box label.
Storage and Stacking
Boxes of plates should remain unopened until use
and be stored flat, on a firm surface, never on end.
All boxes in a stack must be the same size. Do not
stack smaller boxes on top of larger boxes. No more
than 10 boxes of large size raw plates
(42x80/1067x2032 mm and above) should be stacked
on top of each other. Smaller sizes of plates should
not be stacked more than 12 boxes high. Do not
allow boxes to overhang pallets or shelves or be
unsupported for greater than 12 inches between
sides or ends. Opened boxes should not be stacked. They should be stored separately
in a flat position, separated by foam sheeting and protected from light. Do not stack
smaller pieces of product on top of larger pieces without protective dividers, such as
cardboard. Do not stack anything on top of an opened box.
Temperature/Humidity
Plates should be stored in a cool, dry area. Recommended storage temperature is
between 40‐90 deg. F (4‐32 deg. C). Recommended relative humidity is 55% or less.
Rapid changes in temperature and humidity should be avoided. If the workroom
temperature differs significantly from that of the plate storage room, the plates should
be allowed to adapt to the workroom temperature before use.
Section 9‐1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Lighting
Opened boxes and unprocessed photopolymer plates should be handled and stored in
an area protected from light. Exposure to ultraviolet, white incandescent or fluorescent
light, window light, and sunlight can cause pre‐polymerization after prolonged
exposure. For white light illumination, UV filter material can be used in these areas
and also to cover windows and skylights.
Handling Cyrel® Plates
Handle boxes of plates with care. Boxes are properly constructed for handling and
transport, but dropping boxes may damage the structure of the box and its contents.
Raw material should be carried with the coversheet up. Improper handling can flex
the plate, e.g., bending of the plate, and cause delamination of the coversheet or
wrinkling of the release layer. Once an area of the coversheet is delaminated from the
raw plate, it is unusable. Wrinkles can transfer to the plate after imaging. Small sheets
of plate material should be supported evenly with the hand under the sheet. For large
sheets, hold the plate at the edge and transport it in an upright position.
Do not remove the protective polyester coversheet until immediately prior to exposure.
Air bubbles trapped between the raw material and the protective sheets may affect the
raw material. They can cause plate defects that will persist even after processing.
Once the protective sheet is removed from the raw material, it cannot be brought back
into perfect contact with the polymer layer. These plates should be processed
immediately.
To determine which side of the plate contains the strippable polyester coversheet, bend
one corner of the plate upward with your finger. The coversheet will release, the
support will not.
Section 9‐1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Cutting Cyrel® Raw Plates
A sharp cutting tool, such as a paper trimmer, or safety knife and a smooth, flat surface
are essential when cutting raw photopolymer. The blades should sharp and nick‐free.
Do not press down on the material with your hand or fingers. This could create a
depression in the photopolymer. Cut the plate with the coversheet down. The cutting
stroke should be rapid and continuous with the blade held against the cutting board.
A plate should be cut at least ½ inch (12.7mm) larger than the image in both directions.
This will provide a ¼ inch (6.4 mm) border around the image.
Cutting tables with rotating, self‐sharpening knives are available for cutting large‐
sized plates. We recommend the special Cyrel® Cutting Table.
Section 9‐1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Handling, Cleaning, Cutting, Storing Cyrel® Finished Plates
Cutting and Trimming Cyrel® Finished Plates
Cyrel® plates should be trimmed to size, polyester down, using a standard heavy‐
duty paper cutter, sharp razor blade, scissors, or foot shear. When cutting plates, use
a smooth, confident cutting action. The edges of the polyester backing must be cut
cleanly with no nicks or feathered edges. Trim off sharp corners. Bevel the edges of
the plate at an angle of 35°‐45° by placing a cardboard or similar support on the bed
of the paper cutter. The position and height of the support determines the bevel
angle.
Cutting Knife
Cyrel® Plate
Section 9‐2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
To aid plate removal during repositioning and demounting, cut the plate’s four
corners at 45° angles when possible
The Cyrel Cutting Table is also designed and constructed to provide exact and
®
systematic cutting/bevelling of finished Cyrel® photopolymer plates.
Plate/Solvent Compatibility
Once the plate is properly made, carefully mounted and ready for printing, printing
inks, additives, and plate cleaners must be carefully selected to achieve the best results.
Inks, additives and cleaners may contain only limited concentrations of active solvents,
such as acetates, heptane or naphtha. These solvents, and several others, are
incompatible with photopolymer printing plates above certain levels. They may cause
swelling, or in some cases, shrinking, cracking or softening of the plate. Also, UV inks
may contain aggressive monomers that attack the plate, much like aggressive solvents.
A Guide for Cyrel® Plate/Solvent Compatibility is available in the Printing Section of
this manual.
Section 9‐2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Plate Cleaning
One of the tremendous economic advantages of Cyrel® printing plates is their
reusability. This requires proper cleaning and correct storage. Careful cleaning of
Cyrel® printing plates ensures a longer service life of the plates.
After printing, Cyrel® plates should be cleaned immediately and thoroughly of ink. A
soft, natural bristle brush or recommended sponge and compatible cleaner should be
used. Plates should be allowed to dry before storage. Inks should not be allowed to
dry on the surface of the plate, since they become difficult to remove and may require
hard scrubbing. This could lead to surface damage. Dried ink can also crack on the
plate, possibly damaging it. The following can be used to properly clean Cyrel® plates.
Solvent Inks
• Undiluted alcohol
• Solvent blends compatible with the plate
(See Compatibility Guide).
Water‐Based Inks
• Alkaline water with a small amount of
mild, liquid detergent/handsoap.
• Cyrel® Flexo Super Cleaner
• Other compatible blends
Ultraviolet Inks
• Undiluted alcohol
• Solvent blends compatible with the plate
(See Compatibility Guide).
As mentioned before, make certain that cleanup solvents are compatible with the plate.
Check the cleaner’s Material Safety Data Sheet for incompatible components based on
our Plate/Solvent Compatibility Guide found in the Printing Section of this manual. If
necessary, you can also test a small sample of the plate material by first measuring the
thickness of the plate, then immersing it in the solvent for up to 24 hours. Remove the
plate from the solution and re‐measure the plate thickness and examine the surface. If
the plate swells, the plate cleaner is not compatible with the plate.
Aggressive solvents, such as acetates, heptane, or naphtha should not be used for
cleaning plates. Above certain levels, these can cause damage to the plate surface and
Section 9‐2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
swell the plate, thus affecting its durability. When cleaning the plate, wet the plate
thoroughly with the cleaner solution and allow the plate to soak briefly prior to
brushing.
After cleaning the plates, blot or blow them dry. Use a lint‐free towel or cloth. Do not
rub. Rubbing can cause damage to the plate surface. Plates should always be
thoroughly dried before storage.
Plate Staging and Storage
Plates should be protected from the environment at all times. When mounted and
staged for a press run, cleaning, or storage, wrap plates in a black poly with the edges
sealed to protect against whitelight and ozone. Saran™ wrap is an excellent option for
ozone protection; however, if whitelight is present, the plates should also be
wrapped or covered with untreated black poly. When storing flat, protect the plates
by storing them in black poly bags and sealing them.
The procedures listed below should be followed to properly store the carefully cleaned
and dried Cyrel® finished plates.
Storage temperature may range between 40‐95°F (4–35°C).
Do not store near heat sources, heating vents, etc
Humidity does not usually affect finished plate life, and no special
precautions are necessary in the storage area.
Plates must always be protected from UV light, white incandescent or
fluorescent light, window light, and sunlight. Alternately for white
light illumination, a UV filter material can be used.
When storing flat, protect the plates by storing them in black poly bags
and sealing them.
Plates stored on cylinders or sleeves should be wrapped with an opaque
medium, such as untreated black poly, with the edges sealed.
Plates stored in stacks should be interleaved with paper or foam from
raw material packing. Do not stack one plate directly on top of another.
Do not stack over 6 h i g h .
Ozone Protection
Ozone is a gas that forms in the atmosphere. At ground level it is formed when motor
vehicle and industrial exhaust and other chemicals commonly used in the industry mix
in intense heat and sunlight. Corona treaters, extruders, press drives, and other
electrical devices can produce ozone in your printing plant. Photopolymer printing
Section 9‐2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
plates are susceptible to ozone attack. Exposure to ozone can cause cracking on the
plate surface and sometimes on the floor. Ozone attack is most pronounced when the
plate is under stress, such as when mounted, inked, and/or improperly made. The
following steps can minimize ozone damage to Cyrel® plates. All of them may be
required when ozone levels are very high.
Minimizing Ozone
Use optimum platemaking parameters, i.e. optimum exposure times,
especially light finishing times and drying procedures.
Use compatible inks/solvents/plate cleaners.
Protect the plates from the environment at all times.
Clean plates thoroughly; do not leave residual ink on the plate surface.
Follow recommended storage practices, especially for plates stored in a
curved manner.
Store plates in a controlled area, away from sunlight.
Use ozone‐resistant material.
Section 9‐2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Plate Mounting
Correct mounting ensures true color‐to‐color registration of the printing plates, proper
repeat, and no lifting of plates for a problem‐free press run. In the area of plate
mounting for flexible packaging, in particular, there are four principle methods:
1. Microdot Video Mounting,
2. Pin Registration Mounting,
3. Optical, Reflective Mirror Mounting, and
4. Digital Automated Mounting
Microdot Video Mounting
Video mounting, offered by DuPont, has become very popular, primarily in flexible
packaging, as well as narrow and midweb‐type presses. The Cyrel® Microflex®
mounting and proofing system has set a new quality standard in the mounting area.
This mounting system is the fastest method for mounting of Cyrel® plates with high
accuracy in register. Integrated proofing is offered as an option. Information on the
Cyrel® Microflex Mounting Systems are available on our website
Microdots replace traditional registration marks on the plate. The microdot should be
approximately .010”/.25 mm in diameter and normally remains on the plate without
interfering with the production copy. Direct display of the imaged dot on the monitors
ensures a high degree of mounting accuracy and print registration. Job data can also
be stored so that repeat jobs can quickly be set up, and exact camera position is
assured.
Mounting Tapes
A compatible cushion (stickyback) should be selected for optimum image transfer.
Denser cushions help image transfer. The softest stickybacks do not tend to work as
well on digital plates due to the shoulder and dot structure. A firmer cushion
provides better support for digital dots, and is also preferred for high speed gearless
presses. Mounting tapes should be of uniform thickness to obtain maximum
advantage of the consistent and exceptionally uniform Cyrel® plate. Unevenness in
the tape will be seen in the printed results. It is not recommended to re‐use cushion
due to the collapsing nature of the cells.
Section 10‐1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
High Qualify Process Medium Soft Density Tape
Memory colors with either neutral gray or
critical highlights (fleshtones)
Standard Process Medium Soft Density Tape
Tones with a full range of color; no critical
highlights
Combination Medium Density Tape
Areas of line or solid printing with some
process or screen
Line and Solid Hard Density Tape
Majority of print is solids or type
Section 10‐1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Plate Demounting
The proper demounting procedure is important to ensure the plates are in good
condition for future use. A Cyrel® plate demounting tool, or other blunt instrument
(such as a stainless steel spatula/spreader), can be used to demount the plate. No
sharp objects or knives should be used. Avoid kinking the polyester base.
Demounting Procedure
1. Hold the tool at a 45 degree angle
upward from the horizontal.
Starting at the edge of the
mounted plate, insert the corner
of the tool to a 1 / 8 t o ¼ inch
depth (3.1‐ 6.3 mm) between the
stickyback and the polyester
support of the plate.
2. Draw the tool smoothly across.
This will give a free flap of the
plate to grasp and peel the plate
from the stickybacked cylinder.
3. It is important not to use the tool
as a pry bar to remove the plate
from the cylinder. If this
happens, the edge of the plate
will have a wrinkled, wavy
appearance and will be
impossible to hold down to the
cylinder when the plate is
remounted.
If the plate was properly prepared when mounted, by wiping the back with a
varnish solution, demounting should not be a problem. However, if stickyback is
still aggressive, a small amount of alcohol, applied at the contact point between the
stickyback and mounting tape, will assist in removal.
Section 10‐2 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Quality Assurance for Cyrel® Platemaking
Quality Assurance for Cyrel® Platemaking
Quality Assurance (QA) for Cyrel® platemaking includes those planned and
systematic procedures necessary to provide confidence that you will consistently
produce high quality, reliable printing plates. QA also includes quality control,
which relates to checking and reviewing work that has been performed to meet a
required standard.
Developing a quality assurance program for your Cyrel® plateroom is essential to
producing consistent quality printing plates. A brief overview of suggested quality
tools to assist you in establishing an in‐house Quality Assurance Program is listed
below.
Quality Tools
1. Documented procedures (step tests) for optimizing platemaking parameters.
2. Densitometer for checking line screen, dot values, and ensuring complete clearing
of digital plates and film specifications.
3. Digital Micrometer with readout for measuring thickness of raw and finished
plates.
4. The Cyrel® Production Log to document and track finished plate parameters
supplied to the plateroom or your customer.
5. Dryer thermometer to check consistency of dryer drawers (for solvent plates).
6. UV measuring devices to profile and monitor bulb performance and consistency in
your exposure units.
7. Control Targets to monitor and troubleshoot variations within the platemaking
process and press run.
8. Flexo Dot Analyzer for finished plate inspection of halftone dot size, % dot and dot
shape.
9. Solvent Analysis and rebalancing tools and procedures to monitor and maintain
consistent quality washout solvent (for solvent plates).
10. Cyrel® Quality Control Checklist to assess the quality of each plate before printing.
By systematically evaluating each area listed before the plate is sent to press, the
printing plate variable can be eliminated.
To assist you with your quality assurance
Program, the Cyrel® Production Log and Cyrel®
Quality Control Checklist can be found
in another file in the “Quality Assurance” folder.
Section A‐1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Cyrel® Platemaking Quality Control Checklist
Image Integrity (Compare plate to negative or digital file) √
Required dots are held; no dropouts
Positive characters have a sharp, clean shoulder.
All dots are well‐defined, consistent size, and at full plate height. No missing, fallen, or
chipped dots.
Reverse dots and lines are clean, sharp, and open; not filled‐in
Positive lines are sharp, clean and straight; not wavy
There are no “out of contact” spots (Analog Plates) or “out of focus” (Digital Plates).
• no fat type, reverses filled‐in, shiny areas, missing or unsharp image
Entire image, registration marks, microdots have transferred to plate.
Surface Defects (No Surface Defects in the Image Area)
No artifacts, cracks, kinks, pinholes, chipping/broken characters, depressions,
dust/dirt/lint, solvent spots, shiny spots, patterns)
Surface Tackiness
• Plate is not sticky
• Plate is not hazy (excessive light finishing)
• Plate does not haze when the corner is bent back (excessive light finishing).
Uniform Thickness
Process work and line work are approximately the same height
No high or low spots
Relief
Plates are measured in several areas for required/acceptable relief.
Clean Floors (Determine if plate has processed down to the true floor)
No residual monomer on floor or surface
No cracks in floor (could indicate residual monomer)
Trimming
Plate edges have been cleanly trimmed and beveled.
Section A‐2 Cyrel® Process of Use Manual 2008
Cyrel® Photopolymer Platemaking Production Log
Solvent Plates
DuPont Packaging Graphics
Raw Plate Batch Exposure Post Thickness
Date Job # Thickness Description Plate /Box (minutes) Washout Drying Exposure/Finish Gauge Notes
Gauge Type/Size No. Back/Face (minutes) (hours) (minutes) Total/Relief
Daily Check: Weekly Check: Establish Optimum Exposure Times:
Vacuum gauge reading Exposure light intensity When batch number changes
Solvent Temperature Cleanliness of exposure–bulbs, fans, filters After new lamps are burned in
Dryer Temperature Bleeder strip wear For each new product type
Vacuum coversheet Processor solvent tank cleanliness
Cleanlines of exposure bed
Proper solvent replenishment rate
Section A‐3 Cyrel® Process of Use Manual 2008
Cyrel® Photopolymer Platemaking Production Log
Cyrel®FAST Plates
DuPont Packaging Graphics
Raw Plate Exposure Post Exposure Thickness
Date Job # Thickness Description Plate Batch # Box # (minutes) Processor & Finishing Gauge Notes
Gauge Type/Size Back/Face Set-up# (minutes) Total/Relief
Daily Check: Weekly Check: Establish Optimum Exposure Times:
Vacuum gauge reading Exposure light intensity When batch number changes (BX)
Vacuum coversheet Cleanliness of exposure–bulbs, fans, filters After new lamps are burned in
Cleanlines of exposure bed Bleeder strip wear For each new product type
Drum cleaning
Section A‐4 Cyrel® Process of Use Manual 2008
Printing Inks
Printing inks must be carefully selected and formulated for optimal image transfer.
Therefore, for best results, the ink supplier is key to obtaining proper and accurate
ink information.
Flexographic printing inks consist of dyes or pigments, which are dissolved or
dispersed, in an ink vehicle. The ink vehicle consists of synthetic or natural resins
dissolved in suitable ink solvents, which determine the physical properties of the
printing ink. Two important functions of the ink solvent are to control both the
viscosity and drying rate of the printing ink. Flexographic inks are sometimes
classified according to the type of solvent used to dissolve the resin, for example,
alcohol, water, cosolvent inks, etc.
Flexographic printing inks could be based on a single solvent, but in order to
achieve the desired physical and chemical properties, it is more usual to employ
mixtures of solvents. Printing inks may, therefore, contain limited concentrations of
active solvents, such as esters or hydrocarbons, to retain resins in solution. The
composition of a printing ink depends, to a strong extent, on the type of substrate
being printed and on the end‐use requirements of the ink (such as adhesion, heat
resistance, abrasion, deep‐freeze properties, etc.).
Based on extensive laboratory studies, it has been determined that of the major
ingredients contained in an ink (colorant, resin, additives, liquids), it is the liquid
materials that could potentially and adversely influence the plate.
The information in the following section is based on the combination of historical
experience along with static and dynamic testing.
Ink Compatibility
Cyrel® Photopolymer Printing Plates are fully compatible with most alcohol‐based
and water‐based flexographic inks, as well as, solvent mixtures (as shown in the
compatibility section). Inks, which are oil‐based, high in esters, ketones or other
aggressive hydrocarbons, cannot be used since they cause premature swelling
and/or softening of photopolymer plates.
Slower evaporating solvents are often added in higher concentrations because of the
finer anilox rollers and faster running presses. Care should be taken because these
slow solvents, in any amount, can build up on dots creating an oil barrier that
results in dirty printing in addition to premature swelling and softening of the
plate.
®
Cyrel Process-of-Use Manual
CYREL® PACKAGING GRAPHICS
Certain incompatible water‐based antifoams, less than 1% of formula, have been found
to cause plate swell and deterioration after prolonged and repeated exposure.
UV Ink Compatibility
UV inks contain photo reactive monomers, which cure when exposed to ultraviolet
light. Some of these monomers are known to swell and/or soften photopolymer
plates, even at low concentrations.
Since UV Flexographic printing inks vary widely in formulation, it is recommended
to perform a soak test to ensure compatibility prior to printing.
Solvent Compatibility
The Solvent Compatibility List contains mixtures of aggressive solvents with neutral
ones. As neutral solvents n‐Propanol was used for alcohol‐based inks. Pure solvents
which are classified as compatible can, of course, be used in any diluted concentration.
Concentration of aggressive solvents should be lower whenever possible.
Higher concentrations will destroy the plates within a short time and should
never be used. When different non‐compatible solvents are used in the same ink or
plate cleaner, the individual percentages need to be added before comparing to the list.
Please refer to the Solvent Compatibility Guide in this Appendix.
Section B‐1 Cyrel® Process of Use Manual
Global Solvent Compatibility Guide Cyrel®
The summary chart 1 shows consolidated data for resistant (swelling 80µm and /or hardness loss of
7°ShA) or not resistant (swelling > 80µm and/or hardness loss of >7° ShA)
Chart 1: Summary – Solvent compatibility guide
Plate type according family
Solvent
UXL FD1
HIQS SEP FD2
DPI NOW TDR DFS
HOS DS2 NEOS EXL TCP FOP
DPH DPN DPC DFQ
DPR DPU DFH
DPL DFM
Ethanol R R R R R R R R* R R
*
Isopropanol R R R R R R R R* R R
n-Propanol R R R R R R R* R* R R
n-Butanol R R R R R R R* R* R R
n-Pentanol R NR R R R R R* R* R R
* *
o 4h run n-Pentanol R R R R R R R R R R
(1) * *
Methoxybutanol 20% R R R R R R R R R R
Ethoxypropanol 20% R R R R R R R* R* R R
Methoxypropanol 20% R NR R R R R R* R* R R
Ethylacetat 15% NR NR NR R NR NR R* R* NR NR
o 4h run Ethylacetat R R R R R R R R R R
Isopropylacetat 15% NR NR NR NR NR NR R* R* NR NR
o 4h run Isopropylacetat R R R R R R R R R R
n-Propylacetat 15% NR NR NR NR NR NR NR R* NR NR
o 4h run n-Propylacetat R R R R R R R R R R
i-Butylacetat 15% NR NR NR R R NR R R* NR R
o 4h run i-Butylacetat R R R R R R R R R R
n-Butylacetat 15% NR NR NR R R NR R R* NR NR
o 4h run n-Butylacetat R R R R R R R R R R
Methylethylketon 5% R R R R R R R* R* R R
Hexan (=n-Hexan) 5% R NR R R R R R* R* R R
Benzol/Ethylbenzol NR NR NR NR NR NR NR NR NR NR
Toluol NR NR NR NR NR NR NR NR NR NR
Xylol NR NR NR NR NR NR NR NR NR NR
White spirit 40/60 NR NR NR NR NR NR NR NR NR NR
2-Butoxyethanol 5% R R R R R R R* R* R R
Ethanolamin R R R R R R R R R R
Page 1 of 2
section # B-2 Process of Use Manual 2008
* Leach out > 3,5% / standard condition for soak test: 24h into solvent
(1)
volume % mixture with n- (e.g.20% means: 100ml = 20ml solvent
Propanol + 80ml n-Propanol)
Executive Summary:
For the test all common ink and cleaning solvents were tested in the usual percentage.
NEOS, TDR and TCP are the best analog solvent resistant plates. DS2, DPC and DFS are the best digital
solvent resistant plates. DPI and DPH are the most sensitive plates. TDR and TCP are sensitive for leach
out. Over time it can lead to changing the surface properties.
All technical information set out herein is provided free of charge and is based on technical data, which DuPont believes to be
reliable. It is intended for use by persons having skill, at their own discretion and risk. The handling precaution information contained
herein is given with the understanding that those using it will satisfy themselves that their particular conditions of use present no
health or safety hazards. Since conditions of product use are outside of our control we make no warranties express or implied in
relation thereto and therefore cannot accept any liability in connection with any use of this information. Nothing herein is to be
taken as a licence to operate under, or a recommendation to infringe any patents.
Page 2 of 2
section # B-2 Process of Use Manual 2008
DuPont Packaging Graphics
Cyrel® Platemaking Troubleshooting Guide
Platemaking Issues that affect
printing can occur in all stages of
platemaking process.
This Troubleshooting Guide should
help you identify and address
workflow‐related issues.
Sometimes it is difficult to clearly
identify the precise origin of an issue
because a defect has one or more
possible causes. Each cause should be
analyzed separately to identify the
proper steps to take to resolve the
problem.
Section C‐1 Cyrel® Process of Use Manual 2008
Cyrel® Photopolymer Printing Plate Troubleshooting Guide
Key to Defects = All Plates ‐ Green Digital Plates – Blue Analog Plates ‐ Purple
Problem* Probable Cause Problem Identification
Relief out of
Specification
Floor too shallow Back exposure too long Floor
Insufficient washout
Base pre‐exposed during
storage
Floor too deep Insufficient back exposure
No back exposure
Cold lamps
Weak lamps
Dot Variation Improper Bump Curve
‐ Poorly formed Wrong focus adjustment
‐ Sub‐Surface Laser power too low
‐ Fallen over Incorrect dot value in
‐ Missing Highlight computer file or on mask
Dots Main exposure too short
Varying bulb output
Defective exposure ballasts
All bulbs not working
Incorrect bump curve
*Photos are included for “Problems” that are underlined.
Section C-1 Cyrel® Process of Use Manual 2008
/CMC
2
Cyrel® Photopolymer Printing Plate Troubleshooting Guide
Key to Defects = All Plates ‐ Green Digital Plates – Blue Analog Plates ‐ Purple
Problem* Probable Cause Problem Identification
(More on next page) Poor vacuum
Dot Variation (Cont’d) Incorrect dot value on film
‐ Poorly formed Insufficient back exposure
‐ Sub‐Surface (high relief)
‐ Fallen over Low Matte Negative
‐ Missing Highlight Dirt on Negative
Dots Blocked out on negative with
opaque liquid
Out of Contact (Hot Spot)
Shiny spot
Missing image
Loss of Resolution Low/No Matte Film
Fat type & line Poor vacuum
Edge of image not sharp Vacuum Masking Strips used
Reverses filled‐In Improperly or not at all
Shiny spot Poor platemaking technique
Plate mottle
*Photos are included for “Problems” that are underlined.
Section C-1 Cyrel® Process of Use Manual 2008
/CMC
3
Cyrel® Photopolymer Printing Plate Troubleshooting Guide
Key to Defects = All Plates ‐ Green Digital Plates – Blue Analog Plates ‐ Purple
Problem* Probable Cause Problem Identification
Chipped Dots/type Too much main, post, or light
Platemaking finishing exposure
Improper bump curve
(highlight dots)
Insufficient back exposure
Insufficient main exposure
Excessive light finishing
Solvent Plates Only
Excessive washout
Hard, dirty brushes
Excessive brush pressure
*Photos are included for “Problems” that are underlined.
Section C-1 Cyrel® Process of Use Manual 2008
/CMC
4
Cyrel® Photopolymer Printing Plate Troubleshooting Guide
Key to Defects = All Plates ‐ Green Digital Plates – Blue Analog Plates ‐ Purple
Problem* Probable Cause Problem Identification
Printing Harsh cleaning tool
Over‐Impression
Cracked Plates Excessive light finishing
‐ Over‐Light Finishing
‐Slick Surface
‐Hazes when bent
*Photos are included for “Problems” that are underlined.
Section C-1 Cyrel® Process of Use Manual 2008
/CMC
5
Cyrel® Photopolymer Printing Plate Troubleshooting Guide
Key to Defects = All Plates ‐ Green Digital Plates – Blue Analog Plates ‐ Purple
Problem* Probable Cause Problem Identification
Solvent Cracks Aggressive inks, additives,
plate cleaners, antifoams
Ozone Cracks Internal Ozone (extruders,
motors, corona discharge, air
from outside)
External Ozone (hot, humid
days, the environment)
Aggressive inks contribute
*Photos are included for “Problems” that are underlined.
Section C-1 Cyrel® Process of Use Manual 2008
/CMC
6
Cyrel® Photopolymer Printing Plate Troubleshooting Guide
Key to Defects = All Plates ‐ Green Digital Plates – Blue Analog Plates ‐ Purple
Problem* Probable Cause Problem Identification
Light Cracking Excessive exposure to:
Yellow Plates whitelight, incandescent,
UV or any type of light
Over‐impression V‐shaped cracks usually
Cracking coming out of reverses
*Photos are included for “Problems” that are underlined.
Section C-1 Cyrel® Process of Use Manual 2008
/CMC
7
Cyrel® Photopolymer Printing Plate Troubleshooting Guide
Key to Defects = All Plates ‐ Green Digital Plates – Blue Analog Plates ‐ Purple
Problem* Probable Cause Problem Identification
Support Delamination Insufficient back exposure
‐ Base separates from Poor plate trimming
polymer
Aggressive solvents Polymer
Rough handling/mounting Support
White Ink between
Polymer & support
Wavy Lines in Image Line size out of spec
Weak lamps
Insufficient back exposure
Insufficient main exposure
Excessive washout
*Photos are included for “Problems” that are underlined.
Section C-1 Cyrel® Process of Use Manual 2008
/CMC
8
Cyrel® Photopolymer Printing Plate Troubleshooting Guide
Key to Defects = All Plates ‐ Green Digital Plates – Blue Analog Plates ‐ Purple
Problem* Probable Cause Problem Identification
Tacky Plate Surface Insufficient finishing time
‐ Plates stick together Weak finishing lamps
‐ Plate is sticky Insufficient solvent washout
Incompatible ink/plate
cleaner
Insufficient drying time
Thickness Variation
Raw Material Contact Gauge too heavy
Always measure with
coversheet on the plate
Processed Plates Incorrect bump curve
(sub‐surface dots)
Insufficient main exposure
(dots not at full height)
Solvent Plates Only
Insufficient drying time
Drying temperature too low
*Photos are included for “Problems” that are underlined.
Section C-1 Cyrel® Process of Use Manual 2008
/CMC
9
Cyrel® Photopolymer Printing Plate Troubleshooting Guide
Key to Defects = All Plates ‐ Green Digital Plates – Blue Analog Plates ‐ Purple
Problem* Probable Cause Problem Identification
Dryer ventilation incorrect
(too high, too low)
After Printing Aggressive ink, additives,
‐ Plate Swell defoamers, plate cleaners
‐ Dot gain on press Excessive press temperature
‐ Bold Type Abrasion/chipped dots
‐ Plate Shrinkage
Release Layer Not Analog Solvent Only
Washing Off Incorrect washout solution
‐ Shiny area on image temperature
Washout solvent out of spec
Insufficient washout time
Insufficient solvent
replenishment
Dirty solvent tank
Processor brushes too soft
Analog FAST Only
Running wrong processor
*Photos are included for “Problems” that are underlined.
Section C-1 Cyrel® Process of Use Manual 2008
/CMC
10
Cyrel® Photopolymer Printing Plate Troubleshooting Guide
Key to Defects = All Plates ‐ Green Digital Plates – Blue Analog Plates ‐ Purple
Problem* Probable Cause Problem Identification
program
Orange Peel Insufficient back exposure
Insufficient main exposure
Excessive solvent processing
Low alcohol concentration in
the solvent
Solvent dirty
Solvent composition out of
balance
*Photos are included for “Problems” that are underlined.
Section C-1 Cyrel® Process of Use Manual 2008
/CMC
11
Cyrel® Photopolymer Printing Plate Troubleshooting Guide
Key to Defects = All Plates ‐ Green Digital Plates – Blue Analog Plates ‐ Purple
Problem* Probable Cause Problem Identification
Out of Focus Laser Energy too low
‐ Shadow around dots
on mask
‐ Loss of resolution
‐ Laser Lines
On Mask
Plate floor not clean Solvent Plates Only
‐ Uneven floor Insufficient back exposure
‐ Shiny floor Insufficient washout time
‐ Puddling at base of Dirty washout solution
images Inadequate replenishment
‐ Monomer deposits on Weak Exposure bulbs
image surface & floor
‐ Reverses filled in
*Photos are included for “Problems” that are underlined.
Section C-1 Cyrel® Process of Use Manual 2008
/CMC
12
Cyrel® Photopolymer Printing Plate Troubleshooting Guide
Key to Defects = All Plates ‐ Green Digital Plates – Blue Analog Plates ‐ Purple
Problem* Probable Cause Problem Identification
Long Exposure Times Incorrect film specifications
Vacuum film/sheet out of
spec. (MX)
Time not optimized for
product or batch number
UV Lamp age
Long Washout Times Solvent Plates
‐ Washout times longer Solution out of balance
than normal Dirty solution
Under replenished solution
Wrong brush setting
Low drum speed (rotary)
Incorrect solution temp.
*Photos are included for “Problems” that are underlined.
Section C-1 Cyrel® Process of Use Manual 2008
/CMC
13
Cyrel® Photopolymer Printing Plate Troubleshooting Guide
Key to Defects = All Plates ‐ Green Digital Plates – Blue Analog Plates ‐ Purple
Problem* Probable Cause Problem Identification
Plate Curl Relief too high
‐ Plate edge lifts on Incompatible inks, additives,
press plate cleaners, antifoams
‐ Plate edges curl Solvent Plates
upward Excessive washout time
Excessive drying time and/or
high temperature in dryer
Ridges in Screens Solvent Plates
‐ Dot area deformation No back exposure
‐ Area higher than other Insufficient back exposure
areas Insufficient main exposure
*Photos are included for “Problems” that are underlined.
Section C-1 Cyrel® Process of Use Manual 2008
/CMC
14
Cyrel® Photopolymer Printing Plate Troubleshooting Guide
Key to Defects = All Plates ‐ Green Digital Plates – Blue Analog Plates ‐ Purple
Problem* Probable Cause Problem Identification
Reverses Filled‐In Incorrect film density
Low/ no matte film
Blocked vacuum system
Masking strips not used or
used improperly
Over‐Exposed
Reverse too small
Pinholing on Plate Dust/dirt/lint under negative
‐ Tiny Pits in processed or vinyl coversheet
plate Low humidity
Poor ventilation
Poor housekeeping
Poor Registration Check file for design accuracy
‐ Images do not fit Improper loading of plate to
imager (plate sag)
All plates not made in the
same direction on raw mat’l.
All plates not made in the
*Photos are included for “Problems” that are underlined.
Section C-1 Cyrel® Process of Use Manual 2008
/CMC
15
Cyrel® Photopolymer Printing Plate Troubleshooting Guide
Key to Defects = All Plates ‐ Green Digital Plates – Blue Analog Plates ‐ Purple
Problem* Probable Cause Problem Identification
same platemaking system
Different conditions used to
make each plate
Cyrel®FAST Equipment
Issues
Solvent Plates Only
Excessive drying temperature
Excessive drying time
Coversheet Delamination Poor Handling
Raw Material has been bent
Deformation of register Cyrel®FAST Plates
marks, micro dots, fine Image elements out of spec
*Photos are included for “Problems” that are underlined.
Section C-1 Cyrel® Process of Use Manual 2008
/CMC
16
Cyrel® Photopolymer Printing Plate Troubleshooting Guide
Key to Defects = All Plates ‐ Green Digital Plates – Blue Analog Plates ‐ Purple
Problem* Probable Cause Problem Identification
lines on print Insufficient Back Exposure
‐ Characters or small Insufficient Main Exposure
single dots don’t print Mixing plate format sizes
or don’t print Stain level too high in image
completely areas
UV Lamp age
Rough Floor Texture Cyrel®FAST Plates
Relief too deep
Improper back exposure time
(not cleaning to true floor)
*Photos are included for “Problems” that are underlined.
Section C-1 Cyrel® Process of Use Manual 2008
/CMC
17
Cyrel® Photopolymer Printing Plate Troubleshooting Guide
Key to Defects = All Plates ‐ Green Digital Plates – Blue Analog Plates ‐ Purple
Problem* Probable Cause Problem Identification
Wrinkles on Image Handling (Release layer is
disturbed before imaging)
*Photos are included for “Problems” that are underlined.
Section C-1 Cyrel® Process of Use Manual 2008
/CMC
18
CYREL® PACKAGING GRAPHICS
Cyrel® Platemaking Supplies and Sources
Item Source Contact Information
Pre‐Press
High Matte Film for Cyrel® Platemaking Local Graphic Arts Dealer
3M™Temflex™ General Use 1700 Vinyl 3M Part # 054007‐49571
Electrical Tape (for some older digital Electrical Division www.3M.com (to search for distributors)
imagers)
Plate Processing Solutions
Cylosol/OptiSol® DuPont Co./Cyrel® Distributor DuPont # 1‐800‐345‐9999
FlexoSol ®/ Unisol® / Antistat DuPont Co./Cyrel® Distributor
Equipment Support Parts
Exposure Lamps DuPont Co./Cyrel® Distributor DuPont # 1‐800‐345‐9999
Vinyl Cover Sheets DuPont Co./Cyrel® Distributor DuPont # 1‐800‐345‐9999
Embossed Mylar® Local Graphic Arts Dealer www.SDIonline.com (for distributor
search) or call 1‐888‐734‐7734
DuPont In‐line Transport Tape DuPont Co./Cyrel® Distributor DuPont # 1‐800‐345‐9999
Plateroom Support
Platemaking Supplies
Temperature Tape Labels www.omega.com or Non‐Reversible Temperature Labels, Part
Comparable Source Number TL‐10‐105, Temperature Range:
105‐180 deg. F. (Other ranges available)
DuPont Blue Towels (for wiping) DuPont Co./Cyrel® Distributor DuPont # 1‐800‐345‐9999
This listing IS NOT all inclusive of all types of supplies and peripheral equipment available, or all the sources and manufacturers which provide such products. DuPont
does not recommend these suppliers over any other source, and is not responsible for availability, pricing, improper use/handling, or performance of these supplies and
peripheral equipment. Each customer should evaluate the suitability of all supplies and equipment in its operations.
Section D‐1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Cyrel® Platemaking Supplies & Sources
Plateroom Support
Platemaking Supplies
Film Cleaner VWR Scientific or Part # 21899‐490
Comparable Source www.vwr.com
1‐800‐932‐5000
SDI Dust Removal System Roller Local Graphic Arts Dealer www.SDIonline.com (for distributor
search) or call 1‐888‐734‐7734
Magnetic Wiping Cloths Local Graphic Arts Dealer
Room Lighting UV Filters Local Graphic Arts Dealer
Screen Angle Finder Local Graphic Arts Dealer
Orangeplast (for masking) Local Graphic Arts Dealer
Plate Cutters
Dupont Cutting Table (raw & finished) DuPont Co./Cyrel® Distributor Item # M81668A
1‐800‐345‐9999
Kutrimmer (finished plates) MBM Corporation Call for dealer in your area
1‐800‐223‐2508
www.mbmcorp.com
Thermocutter Hot Knife (for raw plates) Abbeon‐Cal, Inc. ZETZ‐24 – Industrial Model
ZETZ‐9 – 8” Hand Held
123 Gray Avenue.
Santa Barbara, CA 93101
1‐805‐966‐7659/1‐800‐922‐0977
This listing IS NOT all inclusive of all types of supplies and peripheral equipment available, or all the sources and manufacturers which provide such products. DuPont
does not recommend these suppliers over any other source, and is not responsible for availability, pricing, improper use/handling, or performance of these supplies and
peripheral equipment. Each customer should evaluate the suitability of all supplies and equipment in its operations.
Section D‐1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
www.abbeon1.com
Vacuum Drawdown
Vacuum Masking Strips (vacuum) DuPont Co./Cyrel® Distributor DuPont # 1‐800‐345‐9999
Flexowand Antistatic Film Drawdown Local Graphic Arts Dealer
Wand
Toraystick Local Graphic Arts Dealer
Pitman Co. Item # 152‐00001
Quality Control Equipment
Dryer Temperature Control VWR Scientific or Item #23609‐230
Comparable Source www.vwr.com
Thermometer Dial (‐50‐l50C/58‐302F) VWR Scientific or Item #61161‐310
Comparable Source www.vwr.com
Loupes (magnifiers) Local Graphic Arts Dealer
Plate Thickness Gauge Cyrel® Distributor or London Model FPI (.0001” increments)
Local Graphic Arts Dealer
Exposure Lamp Meters Kühnast Strahlungstechnik GmbH
UVA ‐ #D11760703 Contact: Ms. Grein, Export Dept.
UVC ‐ #D11760710 Poststrasse 56, D‐63607 Wächtersbach,
Germany, Tel. +49 (0) 6053 / 9650,
E‐Mail: info@uv‐technology.de
Measuring Films & LAMS Layer X‐Rite Incorporated Model # 361T
Tabletop Transmission Densitometer www.xrite.com (to locate Dealers)
1‐800‐248‐9748
Techkon densitometer T 20 and Wiesbadener Straße 27
illumination plate LP 20 or LP 40 TECHKON GmbH D‐61462 Königstein
phone: +49(0) 6174‐924450
www.techkon.com
This listing IS NOT all inclusive of all types of supplies and peripheral equipment available, or all the sources and manufacturers which provide such products. DuPont
does not recommend these suppliers over any other source, and is not responsible for availability, pricing, improper use/handling, or performance of these supplies and
peripheral equipment. Each customer should evaluate the suitability of all supplies and equipment in its operations.
Section D‐1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Spectroeye (spectrophotomer for X‐Rite Incorporated www.xrite.com (to locate Dealers)
measuring print samples 1‐800‐248‐9748
Flexo Dot Analyzers
Betaflex 334 Beta Industries, Inc. 1‐800‐272‐7336
1‐201‐939‐2400
http://www.betascreen.com
Flexo IAS‐II Quality Engineering Associates, Inc. 99 South Bedford Street, Unit 4
Burlington, MA 01803
1‐781‐221‐0080
http://www.qea.com
Safety Supplies
Absorbent for Spills Local Safety Supply Distributor
Protective Gloves ( for handling solvents) Local Safety Supply Distributor Ansell Sol‐Vex®, Style 37‐155
(11 mils thick; 13” length) or equivalent
Safety Glasses, Chemical Splash Goggles Local Safety Supply Distributor
Welding Helmet (Shade 6) Local Safety Supply Distributor
Respirators with organic vapor cartridges Local Safety Supply Distributor Important Note: See OSHA 29 CFR
1910.134, Respiratory Protection
Solvent Rebalancing
Hydrometers VWR Scientific or OptiSol® Rotary Item # 34670‐161
Comparable Source OptiSol® InLine Item #34627‐130
Cylosol Item #34627‐130
www.vwr.com
Graduated Cylinders VWR Scientific or Item # 89001‐232 (340 ml) 38x375 mm
This listing IS NOT all inclusive of all types of supplies and peripheral equipment available, or all the sources and manufacturers which provide such products. DuPont
does not recommend these suppliers over any other source, and is not responsible for availability, pricing, improper use/handling, or performance of these supplies and
peripheral equipment. Each customer should evaluate the suitability of all supplies and equipment in its operations.
Section D‐1 Cyrel® Process of Use Manual 2008
CYREL® PACKAGING GRAPHICS
Comparable Source www.vwr.com
Thermometer for measuring specific VWR Scientific or Item # 61161‐310
gravity Comparable Source www.vwr.com
Solvent Recovery
Solvent Recovery Units (PRI) DuPont Co./Cyrel® Distributor
Parts and Supplies for PRI Units PRI (Progressive Recovery, Inc.) 700 Industrial Drive
Dupo, IL 62239
1‐618‐286‐5000/1‐800‐732‐3793
www.progressive‐recovery.com
Pressroom Supplies
Hydra‐Sponge™ Local Hardware Store or
U.S. Wholesale Supply, Inc. (large Item # SPHs0800 (#2M)
quantities) 2125 Ponticello Dr.
Henderson, NV 89052
1‐800‐472‐8453
Natural Bristle Plate Brush #89540 Advance Product Co. or 1015 Spring Garden Street
Comparable Source Philadelphia, PA 19123
1‐215‐232‐5926
Cyrel® Flexo Super Cleaner DuPont Company/Cyrel® Distributor Item # M70959 (5 gal), M70940 (55 gal)
This listing IS NOT all inclusive of all types of supplies and peripheral equipment available, or all the sources and manufacturers which provide such products. DuPont
does not recommend these suppliers over any other source, and is not responsible for availability, pricing, improper use/handling, or performance of these supplies and
peripheral equipment. Each customer should evaluate the suitability of all supplies and equipment in its operations.
Section D‐1 Cyrel® Process of Use Manual 2008
To learn more, visit www.cyrel.com or contact your Cyrel® specialist.
All technical information set out herein is provided free of charge and is based on technical data which DuPont believes to be reliable.
It is intended for use by persons having skill, at their own discretion and risk. The handling precaution information contained herein
is given with the understanding that those using it will satisfy themselves that their particular conditions of use present no health or
safety hazards. Since conditions of product use are outside of our control, we make no warranties express or implied in relation thereto
and therefore cannot accept any liability in connections with any use of this information. Nothing herein is to be taken as a license to
operate under, or a recommendation to infringe, any patents.
Copyright © 2008 DuPont. The DuPont Oval Logo, DuPont™, The miracles of science™, and Cyrel® are trademarks or registered
trademarks of E.I. du Pont de Nemours and Company or its affiliates. All rights reserved.
H-54635-1 (Revised 10/08)
You might also like
- Relationships Between The Surface Texture of Flexographic Printing Plates and The Printability of Kraft PaperNo ratings yetRelationships Between The Surface Texture of Flexographic Printing Plates and The Printability of Kraft Paper11 pages
- NLS 200 All Wheel Drive Crew Cab Australiano PDFNo ratings yetNLS 200 All Wheel Drive Crew Cab Australiano PDF4 pages
- Press: Flexible. Easy. Intelligent. Accurate Color On All Printing DevicesNo ratings yetPress: Flexible. Easy. Intelligent. Accurate Color On All Printing Devices4 pages
- Flexography Distortion: (Continue On Next Page .)No ratings yetFlexography Distortion: (Continue On Next Page .)2 pages
- Developments in Prepress Technology (PDFDrive)No ratings yetDevelopments in Prepress Technology (PDFDrive)62 pages
- The Secret of A Guide: Superior Flexo QualityNo ratings yetThe Secret of A Guide: Superior Flexo Quality14 pages
- Troubleshooting Guide Printing Issues 2008No ratings yetTroubleshooting Guide Printing Issues 200821 pages
- Alert Packaging HD Flexographic Artwork Guide V1a PDFNo ratings yetAlert Packaging HD Flexographic Artwork Guide V1a PDF8 pages
- Reference Manual Printing and Converting PerformanceNo ratings yetReference Manual Printing and Converting Performance74 pages
- Pigments Training - Printing - Doman-ShotwellNo ratings yetPigments Training - Printing - Doman-Shotwell18 pages
- 1309 FlexoTech Colour Management For Flexo Part IINo ratings yet1309 FlexoTech Colour Management For Flexo Part II3 pages
- Introduction To The G7 Proofing and Printing System Calibration MethodologyNo ratings yetIntroduction To The G7 Proofing and Printing System Calibration Methodology6 pages
- Sappi Technical Series Folding and ScoringNo ratings yetSappi Technical Series Folding and Scoring20 pages
- Devicelink Profiles Fundamentals and Applications 2nd Edition PDFNo ratings yetDevicelink Profiles Fundamentals and Applications 2nd Edition PDF38 pages
- Selecting A Paper For G7 Calibration PDFNo ratings yetSelecting A Paper For G7 Calibration PDF3 pages
- Gravure Flexography and Screen PrintingNo ratings yetGravure Flexography and Screen Printing169 pages
- XSYS Nyloflex® Flexo Photopolymer Plates Products Overview Innvestio HellasNo ratings yetXSYS Nyloflex® Flexo Photopolymer Plates Products Overview Innvestio Hellas9 pages
- Printing Inks - Issues, Guidance and Regulations100% (1)Printing Inks - Issues, Guidance and Regulations93 pages
- Understanding Working Principles Laser Printer: Click To Edit Master Subtitle StyleNo ratings yetUnderstanding Working Principles Laser Printer: Click To Edit Master Subtitle Style13 pages
- Get Production Rolling With Rotary Screen PrintingNo ratings yetGet Production Rolling With Rotary Screen Printing8 pages
- OM Manuals - Index List January 2013 PDFNo ratings yetOM Manuals - Index List January 2013 PDF44 pages
- Green Angle EnviroTech Pvt. Ltd. Company ProfileNo ratings yetGreen Angle EnviroTech Pvt. Ltd. Company Profile33 pages
- Modelling The Specific Grinding Energy and Ball Mill Scale-UpNo ratings yetModelling The Specific Grinding Energy and Ball Mill Scale-Up7 pages
- Nss College of Engineering: Bachelor of Technology Electrical and Electronics Engineering University of CalicutNo ratings yetNss College of Engineering: Bachelor of Technology Electrical and Electronics Engineering University of Calicut33 pages
- Building Technology 4 Specifications Writing and Quantity SurveyingNo ratings yetBuilding Technology 4 Specifications Writing and Quantity Surveying5 pages
- (Engineering Materials) High Nitrogen Steels - Structure, Properties, Manufacture, Applications100% (3)(Engineering Materials) High Nitrogen Steels - Structure, Properties, Manufacture, Applications385 pages
- Relationships Between The Surface Texture of Flexographic Printing Plates and The Printability of Kraft PaperRelationships Between The Surface Texture of Flexographic Printing Plates and The Printability of Kraft Paper
- Press: Flexible. Easy. Intelligent. Accurate Color On All Printing DevicesPress: Flexible. Easy. Intelligent. Accurate Color On All Printing Devices
- Alert Packaging HD Flexographic Artwork Guide V1a PDFAlert Packaging HD Flexographic Artwork Guide V1a PDF
- Reference Manual Printing and Converting PerformanceReference Manual Printing and Converting Performance
- 1309 FlexoTech Colour Management For Flexo Part II1309 FlexoTech Colour Management For Flexo Part II
- Introduction To The G7 Proofing and Printing System Calibration MethodologyIntroduction To The G7 Proofing and Printing System Calibration Methodology
- Devicelink Profiles Fundamentals and Applications 2nd Edition PDFDevicelink Profiles Fundamentals and Applications 2nd Edition PDF
- XSYS Nyloflex® Flexo Photopolymer Plates Products Overview Innvestio HellasXSYS Nyloflex® Flexo Photopolymer Plates Products Overview Innvestio Hellas
- Understanding Working Principles Laser Printer: Click To Edit Master Subtitle StyleUnderstanding Working Principles Laser Printer: Click To Edit Master Subtitle Style
- Get Production Rolling With Rotary Screen PrintingGet Production Rolling With Rotary Screen Printing
- Modelling The Specific Grinding Energy and Ball Mill Scale-UpModelling The Specific Grinding Energy and Ball Mill Scale-Up
- Nss College of Engineering: Bachelor of Technology Electrical and Electronics Engineering University of CalicutNss College of Engineering: Bachelor of Technology Electrical and Electronics Engineering University of Calicut
- Building Technology 4 Specifications Writing and Quantity SurveyingBuilding Technology 4 Specifications Writing and Quantity Surveying
- (Engineering Materials) High Nitrogen Steels - Structure, Properties, Manufacture, Applications(Engineering Materials) High Nitrogen Steels - Structure, Properties, Manufacture, Applications