V601-C

T e c h n o l o g y N a t u r e S o c i e t y

Industrial Power Transmission Products

Conveyor Belts
Engineering Plastics
Safety Precautions
Please read all the warnings!

● Please take all necessary precautions when using our products. Also, Please review relevant product
catalog and design documents, etc.
Significances of safety precautions are categorized as follows:

Signs M e a n i n g s

Danger Imminently causing death or severe injury to the user who misuses
products.

Warning Possibly causing death or severe injury to the user who misuses
products.

Caution Possibly causing personal injury or property damage if misused.

Power Transmission Products

Use

● If you expect that a belt will fail and idle, free-run, or stop the system, thus causing a fatal or severe accident, please provide
Danger an extra safety device.
● Do not use a belt as a lifting or towing tool.

● If you expect that static electricity will come from the power transmission belt system, thus causing fire or malfunction of the
Warning controller, use an antistatic belt and set a neutralization apparatus in the system.

● Do not use a belt as an insulator. Contact us for information on insulation properties, which vary in belt type.
Caution ● For a belt that touches food directly, use one that complies with the applicable food hygiene law of your country
● Do not modify a belt, or its quality and performance could deteriorate.

Function & Performance

● Do not use a belt beyond its capacity or for an application other than that specified by the catalog, design documents, etc. This can
cause premature failure of the belt.
Caution ● If water, oil, chemical, paint, dust, etc. sticks to a belt or pulley, its power transmission could deteriorate and the belt may fail.
● A cogged belt makes louder noise during high-speed rotation. If this occurs, use a soundproof cover.

Storage & Transportation

● To store a heavy belt, use a suitable jig or stopper to prevent accidents such as belt toppling or tumbling.
Warning
● Use suitable equipment to carry/handle a heavy belt or pulley. Otherwise, back injury may result.
● Do not put weight on or bend a belt forcibly to carry or store it. Otherwise, it will produce defects or scratches to the belt,
Caution resulting in damage.
● Store the belt in low humidity and a temperature range of -10°C to 40°C. Do not expose belts to direct sunlight.

Mounting & Operation

● Install a safety cover over rotating components including belt/ pulley. Otherwise, hair, gloves and clothing can become
entangled in the belt/ pulley. If a belt/pulley breaks, fragments may cause injuries.
● Take the following precautions to maintain, inspect and replace a belt.
Danger
1)Turn off power and wait until the belt and pulley have stopped completely.
2)Secure machinery so that it may not move during belt removal.
3)Use caution : Do not unintentionally turn on power.

● Use the same type of belts or pulleys per OEM specification. Use of a different type may cause premature failure.
● Misalignment of the pulleys can damage the belt and result in flange failure. Make proper adjustments to system.
● Loosen the belt tension when changing belts. Do not force or stretch a belt over the flange. Do not use a screw driver or other
sharp objects into when replacing the belt as this will result in damage.
● Apply the appropriate belt tension as specified by the relevant catalog and design documents, etc. Inappropriate tension could
Caution result in damage of the belt and shaft.
● Take the following precautions to modify the pulley in use:
1) Remove burrs and maintain proper pulley angle; 2)Secure accurate dimensions after modification;
3) Maintain the pulley strength after modification.
● Before assembling the flange with the pulley, check for foreign materials between the pulley and flange. Fasten the flange with
a caulking tool and so on. Inappropriate installation could result in the flange coming off.

Handling of Used items

Caution ● Do not burn belt, or hazardous gas could be produced.

Plastic Conveyor Belts
Use

● Do not use the belt as a lifting or towing device.

Warning ● To convey unpackaged food, use a belt that complies with the applicable food hygiene law of your country.

Storage & Transportation

Warning ● To store a large plastic conveyor belt, use a suitable jig or stopper to prevent accidents due to belt toppling or tumbling.

Caution ● Use suitable equipment to carry and handle large plastic conveyor belts. Otherwise, back injury may result.

Mounting & Operation

● Before fitting and inspecting the plastic conveyor belt, be sure to turn off the power of the conveyor and related systems and check to make sure that
Danger conveyor has stopped, so as to prevent accidents.
● Fix a safety guard to avoid close contact with conveyor belt in use. Otherwise, you may become entangled in the conveyor system.

Installation Works

Warning ● Solvent and adhesive used for endless type belts is flammable. No open flames are allowed during operation.

Engineering Plastic Products

Use

Warning ● Do not use the product for medical purposes, such as transplantation or in such a way that it touches bodily fluids or tissues.

Storage & Transportation

● Injury may occur as a result of a product falling. Use proper equipment especially when carrying a large product and install it into processing machinery.
● A pile of products on an uneven place could slip, collapse or topple by gravity. Store products on a flat shelf or pallet that won’t bend under product weight.
Caution ● Static electricity may spark. Do not rub products against insulators like paper, cloth, plastic.
● Gas will occur from burning product. Keep away from fire.

Process

● Product may break up due to partial heat generated by forced processing. To reduce over heating, use air, cutting oil or a sharp cutting tool, and adjust its
Caution feeding speed. Pay special attention to bore processing which generates heat easily.
● As the product is less elastic than metal, it could deform and come off the chuck, scattering materials if it doesn’t fit properly on the processing machinery. Fix
the product firmly, taking care not to deform materials.

Couplings
Use

● Provide an additional safety device if you expect that a fatal or severe accident may occur if the coupling breaks or comes off, and then idles, free-runs or
Danger stops the system.

Function & Performance

Caution ● Do not use product beyond its capacity or for applications other than specified in the catalog, design documents, etc. Otherwise, the product could fail prematurely.

Storage & Transportation

Warning ● Use an appropriate jig or stopper to prevent a large coupling from toppling and tumbling. Do not store coupling at a height where it could fall.

Caution ● Use suitable equipment when carrying or handling a large coupling, depending on its weight. Otherwise, back injury may result.

Mounting & Operation

● Be sure to put a safety cover over the rotating components including the coupling. Otherwise, hair, gloves or clothing may become entangled. Also, injury
may occur if parts fly off.
● Secure coupling. Otherwise, the coupling and its parts may come off.
● Take the following precautions to maintain, inspect or replace coupling:
Danger 1) Turn off the power and wait until the machine stops completely.
2) Fix machinery so that it may not move during removal of the coupling.
3) Take care not to unitentionally turn on the switch.
● Before you operate the machine, check to make sure unused bolts or tools do not remain after installation of the coupling. If operation starts with unused
items being left behind, they could be flung off, causing injuries.

● Replace the same type of couplings. Use of a different type of coupling will result in earlier damage.
Caution ● Adjust coupling properly Otherwise, deflection or declination will damage or displace the coupling.

Handling of Used items

Danger ● Do not burn the coupling. Otherwise, hazardous gas could be produced.
 I N D E X

CONTENTS
Safety Precautions.....................................................P1,2
1. Power Transmission Belts
and Related Products ................................P4~68
2. Conveyor Belts ...........................................P69~77
3. Engineering Plastic Products ...............P78~85
Global Factories & Sales Offices...............................P88

3
1. Power Transmission Belts
and Related Products
Application Examples ................................................................ P5, 6
Lineup of Belts and Related Products ..................................... P7, 8
Industrial Power Transmission Product Selection Chart ...... P9,10
Dimensions ................................................................................... P11

1 Synchronous Power Transmission

Round Tooth Timing Belt Trapezoidal Tooth Timing Belt
Belt Type, Dimensions & Product Code. . . . . . . . . . . . . . . . P13 Belt Type, Dimensions & Product Code. . . . . . . . . . . . . . . . P21
SUPER TORQUE Timing Belt GN . . . . . . . . . . . . . . . . . . P14, 15 Timing Belt G ...................................................... P22∼24
SUPER TORQUE Timing Belt G . . . . . . . . . . . . . . . . . . . . . . . . . P16 Timing Belt U ....................................................... P25, 26
SUPER TORQUE Timing Pulley . . . . . . . . . . . . . . . . . . . . . . . . . . P17 green eco® Series ...................................................... P27
MEGA TORQUE Timing Belt G&U . . . . . . . . . . . . . . . . . . P18, 19 Timing Pulley ........................................................ P28, 29
H Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P20 Other type of Timing Belt
green eco® Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P27 LONG-SPAN Timing Belt ............................................ P30

2 Frictional Forced Power Transmission

Classical V-Belt / Red label V-Belt .............................P32 RIBSTAR Belt U (Polyurethane V-Ribbed Belt) ........P45
Classical V-Belt / Red label V-Belt RIBSTAR Pulley (V-Ribbed Pulley) .............................P46
for DIN2215 / ISO4184 .........................................P33∼36 FLEXSTAR® Belt ...........................................................P47
MAXSTAR WEDGE V-Belt............................................P37 SUPER FLEXSTAR® Belt ..............................................P48
MAXSTAR WEDGE V-Belt for RMA / MPTA ...............P38 FLEXSTAR® Belt J .......................................................P49
Narrow V-Belt for DIN7753 / ISO4184 ........................P39 POLYMAX Belt ..............................................................P50
SUPER VS® Belt (Variable Speed Belt) ......................P40 MB Belt .........................................................................P51
MAXSTAR WEDGE Bushing Pulley .....................P41, 42 STARROPE®, SUPER STARROPE® ............................P52
e-Power® Belt .............................................................P43 PRENE V-ROPE, PRENE HEXAGONAL-ROPE ..........P52
RIBSTAR Belt G (Rubber V-Ribbed Belt) ...................P44 Flat Belt .........................................................................P53

3 Direct Connected Power Transmission

Chemi-Chan®
(High Performance Miniature Coupling) . . . . . . . . . . . . . . P55
HYPERFLEX® Coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P56
TSCHAN® Coupling NOR-MEX® . . . . . . . . . . . . . . . . . . P57, 58
TSCHAN® Coupling S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P59, 60

4 Other Related Products

SLEEVE ROLL
(Polyurethane molded product) ................................ P62
STARLOCK®(Shaft Fastener) .............................. P63, 64

5 Troubleshooting for Power Transmission Products

For Timing Belt ......................................................... P67
For V-Belt ................................................................... P68

4
 Direct Connected Power Transmission
Synchronous Power Transmission &

Large Knitting Machine (SUPER TORQUE Timing Belt)

Polisher (SUPER TORQUE Timing Belt)

Copier (Rubber Timing Belt)

Application
Example
Power Transmission
Frictional Forced

Heavy Duty Polisher (MAXSTAR WEDGE V-Belt)

Combine (V-Belt for Agricultural Machines) Food Processor (RIBSTAR Belt)

5
Marine Engine (TSCHAN® Coupling S ) Plastic Card Vender (Polyurethane Timing Belt)

Packaging Machine (Polyurethane Double Timing Belt) Actuator (Chemi-Chan®)

Dryer (V-Belt)

NC Lathe (RIBSTAR Belt)

∗ To show the application examples clearly, safety covers are removed in the
pictures on this page.
NC Lathe (Multi-POLYMAX Belt) Always put on the safety covers when in use.

6
 Lineup of Belts & Related Products

Product Name & Application Product Name & Application

SUPER TORQUE Timing Belt Classical V-Belt
(General use) (General use)

MEGA TORQUE Timing Belt G&U Multi V-Belt

(Heavy-duty use) (General use : Joined V-Belt)

Timing Belt G Less Thickness Wrapped V-Belt

(General use : Rubber)
( LA, LB, LC
Agricultural use )
Timing Belt

Timing Belt U BARE-BACK® V-Belt

(General use : Polyurethane) (Agricultural use, Washer and Dryer)

green eco® Series MAXSTAR WEDGE V-Belt

(Heavy-duty use)
Wrapped Belt

LONG-SPAN Timing Belt Multi MAXSTAR WEDGE V-Belt

(Endless & Open-End) (Joined V-Belt for Heavy-duty)
Timing Pulley

Timing Pulley e-POWER® Belt

(Notched type)

Chemi-Chan® Perforated V-ROPE

(High Performance
Miniature Coupling)

TSCHAN® Coupling NOR-MEX® V-Belt with lugs

Coupling

(Agricultural use)

TSCHAN® Coupling S HEXAGONAL V-Belt

7
 Product Name & Application Product Name & Application
Orange label RIBSTAR Belt G

Ribbed Belt
Raw Edge COGGED V-Belt (Rubber)
(Agricultural use)

RIBSTAR Belt U
(Polyurethane)
SUPER GOLD 1000 POLYMAX Belt
Raw Edge COGGED V-Belt (Wide-angle Polyurethane V-Belt)
(Agricultural use)

Raw Edge MULTI-PLY V-Belt MB Belt

Polyurethane Belt
(Automotive use) (For Sewing Machine)
Raw Edge Belt

Raw Edge COGGED V-Belt STARROPE® & SUPER STARROPE®

(Automotive use) (Polyurethane Round Rope)

Raw Edge COGGED PRENE V-ROPE & HEXAGONAL-ROPE (Polyurethane Rope)

Variable Speed Belt

e-POWER® Belt FLEXSTAR®

(Cogged type)

Pulley and Bushing SUPER FLEXSTAR®

for WEDGE V-Belt (Heavy-duty use)
Flat Belt
Pulley

Pulley and Bushing FLEXSTAR® Belt J

for RIBSTAR Belt (For Conveyor)

MB BUSHING Flat Belt

(For Lifter)
Bushing
Polyurethane Molded

SLEEVE ROLL Flat Belt

(General use)

8
 ■ Industrial Power Transmission Product Selection Chart
How much slip How do you What features
can you allow? want to use it? do you need?

Slip
Tolerance

green eco Series

green eco Series

MEGA TORQUE U

S
N

Rubber dust free,

belt clutch

Top width
Top width
Some slip is
allowed.

FREESPAN Flat Belt

Good driving
stability, compact FLEXSTAR Belt J
design, maintenance-
free

HEXAGONAL V-Belt

PRENE V-ROPE
PRENE HEXAGONAL-ROPE

V-Belt with lugs

Chemi-chan

9
A wide range of products are available at Mitsuboshi to suite your needs.
Refer to the following property chart when selecting belts.

10
 ■ Dimensions
Cross-Sectional Dimensions Minimum Pulley Diameter Highest Speed
Model Material Type
top width (mm) x thickness (mm) x angle (°) (mm) (m/sec)
SUPER TORQUE Timing Belt S1.5M Pitch (mm) 1.50 9 30 (40)
(Round tooth) S2M 2.00 9 30 (40)
S3M 3.00 13 30 (40)
Rubber
S5M 5.00 22 30 (40)
S8M 8.00 56 30 (40)
S14M 14.00 151 30 (40)
S2M 2.00 9 30 (40)
Polyurethane
S3M 3.00 13 30 (40)
MEGA TORQUE Timing Belt MTS5M Pitch (mm) 5.00 22 30
Rubber MTS8M 8.00 56 30
MTS14M 14.00 151 30
Polyurethane MTS8M Pitch (mm) 8.00 61 30
Timing Belt MXL Pitch (mm) 2.032 7 30 (40)
(Trapezoidal tooth) XL 5.08 16 30 (40)
L 9.525 30 30 (40)
Rubber
H 12.700 57 30 (40)
XH 22.225 127 30 (40)
XXH 31.750 182 30 (40)
T80 Pitch (mm) 2.032 7 30 (40)
T5 . DT5 5.0 19 30 (40)
Polyurethane T10 . DT10 10.0 45 30 (40)
XL 5.08 16 30 (40)
L 9.525 30 30 (40)
Classical V-Belt A 12.5x 9.0x 40 95 ( 67) 30
B 16.5x 11.0x 40 150 ( 118) 30
Rubber C 22.0x 14.0x 40 224 ( 180) 30
D 31.5x 10.0x 40 355 ( 300) 30
E 38.0x 25.5x 40 560 ( 450) 30
MAXSTAR WEDGE V-Belt 3V 9.5x 8.0x 40 67 40
Rubber 5V 15.9x 13.5x 40 180 40
8V 25.4x 22.0x 40 315 40
Multi MAXSTAR WEDGE V-Belt 3V - 67 40
(Joined V-Belt) Rubber 5V - 180 40
8V - 315 40
RIBSTAR Belt
J Pitch (mm) 2.34 31.5 ( 25) 40 (50)
( V-Ribbed Belt)
Rubber PK 3.56 56 ( 50) 40 (50)
L 4.70 90 ( 80) 40 (50)

Polyurethane JT . JBT Pitch (mm) 2.34 20 30 (35)

FLEXSTAR® Belt FL Belt Thickness (mm) 1.5 16 40 (60)
Rubber FM 2.5 40 40 (60)
FH 3.5 80 40 (60)
POLYMAX Belt 3M 3.0x 2.0x 60 17 40
5M 5.0x 3.0x 60 26 40
Polyurethane
7M 7.0x 5.0x 60 42 40
11M 11.0x 7.0x 60 67 40
MB Belt (Polyurethane V-Belt) Polyurethane MB 6.0x 4.0x 40 16 10
STARROPE®/ SUPER STARROPE® 2 Diameter φmm 2 15/ 20 SUPER 10 and below
3 3 20/ 30 10
4 4 30/ 40 10
5 5 40/ 50 10
6 6 50/ 60 10
Polyurethane 7 7 60/ 70 10
8 8 70/ 80 10
9 9 85/ 90 10
10 10 95/ 100 10
12 12 120/ 120 10
15 15 150/ 150 10
PRENE V-ROPE M 10.0x 5.5x 40 40 10 and below
Polyurethane A 12.5x 8.5x 40 85 10
B 16.5x 10.5x 40 100 10
PRENE HEXAGONAL-ROPE AA 12.5x 10.0x 40 100 10 and below
Polyurethane
BB 16.5x 12.5x 40 130 10
Note 1 Values in ( ) are only used under limited conditions. Avoid these values as much as possible.
The conditions of use such as pulley diameter and speed affect belt durability.
(Use the above table as a reference when selecting belts)
Note 2 For V-Belt and MAXSTAR WEDGE V-Belt, values are nominal.

11
11
1 Synchronous Power
Transmission
Round Tooth Timing Belt
Belt Type, Dimensions & Product Code ....... P13
SUPER TORQUE Timing Belt GN ............ P14,15
SUPER TORQUE Timing Belt G ................... P16
SUPER TORQUE Timing Pulley ..................... P17
MEGA TORQUE Timing Belt G&U ........... P18,19
H Series .......................................................... P20
green eco® Series ........................................... P27
Trapezoidal Tooth Timing Belt
Belt Type, Dimensions & Product Code .......... P21
Timing Belt G .......................................... P22∼24
Timing Belt U ........................................... P25, 26
green eco® Series .......................................... P27
Timing Pulley ........................................... P28, 29
Other Timing Belt
LONG-SPAN Timing Belt................................ P30

12
 Synchronous Power
Transmission

Round Tooth Timing Belt

Belt Type, Dimensions & Product Code

Minimum Pulley Size

Product Code

Pitch Line
1Synchronous Power

Belt Belt Type

Transmission

Type

Nominal Length (mm)

Belt Tooth Pitch 1.5mm Belt Width(mm)x10

Pitch Line

Belt Belt Type

Type

Nominal Length (mm)

Belt Width(mm)x10 U(polyurethane)

Belt Tooth Pitch 2mm Type

Pitch Line

Belt Belt Type

Type

Nominal Length (mm)

Belt Tooth Pitch 3mm
Belt Width(mm)x10 U(polyurethane)
Type

Pitch Line

Belt
Belt Type
Type

Nominal Length (mm)

Belt Tooth Pitch 5mm
Belt Width(mm)x10

Belt Width Nominal 56.02

(mm)x10 Length (mm)
Belt Type
Belt Tooth Pitch 8mm

Type

Belt Width Nominal

(mm)x10 Length (mm)

Belt Type
Belt Tooth Pitch 14mm

Type

13
13
 Synchronous Power
Transmission

SUPER TORQUE Timing Belt GN

Since the round tooth shape allows smooth meshing with pulleys, this
belt is the most suitable for applications which require high-accuracy and
smooth revolution such as computers and office appliances.
● Improved flexibility of this belt enables use of smaller diameter pulleys
● Smooth meshing allows noiseless operation
● Usable with low shaft load
● Possible to transmit high torque with a small belt.

Standard Belt Sizes

Code(width)
Manufacturable Size Manufacturable Size Manufacturable Size
Product Code Product Code Product Code

1Synchronous Power
Transmission

For S1.5M, S2M and S3M, polyurethane (U) and rubber (G) models are available. Choose the appropriate material for your application.

Sizes not indicated above are also available under limited conditions.

14
 Synchronous Power
Transmission

SUPER TORQUE Timing Belt GN

Standard Belt Sizes

Code(width)
Manufacturable Size Manufacturable Size
Product Code Product Code Product Code
1Synchronous Power
Transmission

For S1.5M, S2M, and S3M, polyurethane (U) and rubber (G) models are available. Choose the appropriate material for your application.

15
15
 Synchronous Power
Transmission

SUPER TORQUE Timing Belt G

Since this round tooth belt has a high power transmission
property, it expands existing applications of timing belts
significantly.
Also, it can be used as an alternative for chains and gears.

● It can be used in wide applications since it has a higher power transmission.

● Longer operating life
● Quiet operation
● Cost-Efficient

Standard Belt Sizes

1Synchronous Power
Transmission
Code(width)
Product Code Product Code

16
 Synchronous Power
Transmission

SUPER TORQUE Timing Pulley

Timing belt power transmission system works the best when belt and
pulley smoothly mesh with each other.
Our SUPER TORQUE Timing Pulley is made with specially formed
tooth shape and fine finishing.

Pulley Product Code Example:

P 28 S5M 0100 B
Pulley Pulley Type
No. of Pulley Teeth Pulley Width Code
Belt Type (Belt With (mm) x10)

SUPER TORQUE Standard Pulley Types and Sizes

✫ We add aluminum as a standard pulley for S3M and S5M
1Synchronous Power

Belt Type
Transmission

Standard Sizes Materials Pulley Types

Rod Shape Rod Shape

Shape is a 100mm long round cylinder product.

22 teeth and below sizes of S3M are available only in rod shape and C type. Also, 24 teeth and
above sizes are available only in A or B type.

Belt Type

we revised the standard item lists in April, 2006.

A and B types are made from steel whereas W type is made from cast metal.

17
17
 Synchronous Power
Transmission

MEGA TORQUE Timing Belt G&U

Characteristics of low/high speed torque timing belt
‘MEGA TORQUE’ :
1. Large transmission capacity is achievable, at about 2 times that
of SUPER TORQUE G (Rubber)
(variation subject to pulley diameter and revolution speed).
2. Compact design possible.
Compared to SUPER TORQUE G (Rubber), width is approximately 40%
smaller on average for the same pulley diameter.
MEGA TORQUE MEGA TORQUE 3. Pulley of existing models can be used.
Timing Belt G Timing Belt U SUPER TORQUE (S8M S14M) pulleys can be used as per usual.
`
∗ Please contact us regarding pulley for MTS5M.

Standard Belt Sizes

MEGA TORQUE Timing Belt G

1Synchronous Power
MTS5M(Pitch 5mm)

Transmission
Product Code No. of Teeth Product Code No. of Teeth
- Tooth Shape & Product Code -
MTS5M 225 45 MTS5M 765 153
MTS5M 230 46 MTS5M 780 156
MTS5M 255 51 MTS5M 800 160
Belt Width Code
MTS5M 260 52 MTS5M 810 162
MTS5M 295 59 MTS5M 830 166
MTS5M 300 60 MTS5M 845 169
MTS5M 305 61 MTS5M 850 170
MTS5M 320 64 MTS5M 870 174
MTS5M 325 65 MTS5M 890 178
MTS5M 340 68 MTS5M 900 180
MTS5M 350 70 MTS5M 950 190
MTS5M 360 72 MTS5M 975 195
MTS5M 375 75 MTS5M 1000 200
Belt Width Code
MTS5M 380 76 MTS5M 1025 205
MTS5M 390 78 MTS5M 1050 210
MTS5M 400 80 MTS5M 1055 211
MTS5M 425 85 MTS5M 1085 217
MTS5M 435 87 MTS5M 1090 218
MTS5M 440 88 MTS5M 1100 220
MTS5M 450 90 MTS5M 1105 221
MTS5M 475 95 MTS5M 1115 223
MTS5M 490 98 MTS5M 1120 224
MTS5M 500 100 MTS5M 1125 225
Belt Width Code
MTS5M 520 104 MTS5M 1135 227
MTS5M 525 105 MTS5M 1145 229
MTS5M 530 106 MTS5M 1160 232
MTS5M 545 109 MTS5M 1165 233
MTS5M 550 110 MTS5M 1195 239
MTS5M 560 112 MTS5M 1225 245
MTS5M 575 115 MTS5M 1250 250
MTS5M 590 118 MTS5M 1270 254
MTS5M 595 119 MTS5M 1295 259
MTS5M 600 120 MTS5M 1350 270
MTS5M 625 125 MTS5M 1420 284
MTS5M 640 128 MTS5M 1475 295
MTS5M 650 130 MTS5M 1500 300
MTS5M 665 133 MTS5M 1505 301
MTS5M 670 134 MTS5M 1530 306
MTS5M 675 135 MTS5M 1595 319
MTS5M 690 138 MTS5M 1605 321
MTS5M 695 139 MTS5M 1680 336
MTS5M 700 140 MTS5M 1715 343
MTS5M 710 142 MTS5M 1800 360
MTS5M 720 144 MTS5M 2000 400
MTS5M 725 145 MTS5M 2145 429
MTS5M 730 146 MTS5M 2255 451
MTS5M 740 148 MTS5M 2480 496
MTS5M 750 150 MTS5M 2525 505

18
 Synchronous Power
Transmission

MEGA TORQUE Timing Belt G&U

Standard Belt Sizes

MEGA TORQUE Timing Belt U
1Synchronous Power

MTS8M (Pitch 8 mm) MTS14M (Pitch 14 mm)

Transmission

Product Code No. of Teeth Product Code No. of Teeth Product Code No. of Teeth
- Tooth Shape & Product Code -
MTS8M 528 66 MTS8M 1384 173 MTS14M 1008 72
MTS8M 560 70 MTS8M 1400 175 MTS14M 1120 80
MTS8M 584 73 MTS8M 1424 178 MTS14M 1190 85
MTS8M 600 75 MTS8M 1440 180 MTS14M 1246 89
MTS8M 632 79 MTS8M 1480 185 MTS14M 1288 92
MTS8M 640 80 MTS8M 1488 186 MTS14M 1400 100
MTS8M 656 82 MTS8M 1520 190 MTS14M 1470 105 Reinforcement
Fabric
MTS8M 712 89 MTS8M 1552 194 MTS14M 1540 110
MTS8M 720 90 MTS8M 1600 200 MTS14M 1610 115
MTS8M 760 95 MTS8M 1640 205 MTS14M 1652 118
MTS8M 800 100 MTS8M 1648 206 MTS14M 1708 122
MTS8M 824 103 MTS8M 1680 210 MTS14M 1750 125
MTS8M 840 105 MTS8M 1696 212 MTS14M 1778 127
MTS8M 848 106 MTS8M 1728 216 MTS14M 1806 129
MTS8M 856 107 MTS8M 1760 220 MTS14M 1890 135
MTS8M 880 110 MTS8M 1776 222 MTS14M 1932 138
MTS8M 896 112 MTS8M 1792 224 MTS14M 2002 143
MTS8M 912 114 MTS8M 1800 225 MTS14M 2100 150
MTS8M 920 115 MTS8M 1816 227 MTS14M 2198 157
MTS8M 928 116 MTS8M 1832 229 MTS14M 2240 160
MTS8M 944 118 MTS8M 1880 235 MTS14M 2310 165 Standard Belt Sizes
MTS8M 952 119 MTS8M 1912 239 MTS14M 2380 170
MTS8M 960 120 MTS8M 1960 245 MTS14M 2450 175 MTS8M (Pitch 8 mm)
MTS8M 976 122 MTS8M 2000 250 MTS14M 2506 179 Product Code No. of Teeth
MTS8M 1000 125 MTS8M 2040 255 MTS14M 2590 185
MTS8M 1024 128 MTS8M 2048 256 MTS14M 2660 190 MTS8M 560 70
MTS8M 1040 130 MTS8M 2064 258 MTS14M 2800 200 MTS8M 600 75
MTS8M 1056 132 MTS8M 2104 263 MTS14M 3150 225 MTS8M 640 80
MTS8M 1080 135 MTS8M 2120 265 MTS14M 3500 250 MTS8M 680 85
MTS8M 1120 140 MTS8M 2160 270 MTS14M 3556 254 MTS8M 720 90
MTS8M 1128 141 MTS8M 2240 280 MTS14M 3850 275 MTS8M 760 95
MTS8M 1136 142 MTS8M 2272 284 MTS14M 4004 286 ∗ MTS8M 800 100
MTS8M 1152 144 MTS8M 2304 288 MTS14M 4508 322 MTS8M 848 106
MTS8M 1160 145 MTS8M 2400 300 MTS14M 5012 358 MTS8M 896 112
MTS8M 1184 148 MTS8M 2496 312 MTS8M 960 120
MTS8M 1200 150 MTS8M 2600 325 MTS8M 1000 125
MTS8M 1216 152 MTS8M 2800 350 MTS8M 1056 132
MTS8M 1248 156 MTS8M 2920 365 MTS8M 1120 140
MTS8M 1256 157 MTS8M 2944 368 MTS8M 1200 150
MTS8M 1280 160 MTS8M 3048 381 MTS8M 1280 160
MTS8M 1296 162 MTS8M 3200 400 ∗ MTS8M 1328 166
MTS8M 1304 163 MTS8M 3272 409 MTS8M 1360 170
MTS8M 1312 164 MTS8M 3440 430 MTS8M 1440 180
MTS8M 1320 165 MTS8M 3680 460 MTS8M 1520 190
MTS8M 1352 169 MTS8M 4400 550 MTS8M 1600 200
MTS8M 1360 170 MTS8M 1696 212
∗ MTS8M 1792 224
∗ MTS8M 1888 236

●Total thickness of belt sizes with ∗ mark is 4.8mm.

19
19
 Synchronous Power
Transmission

H Series
Round -shape belt teeth enable the distribution of load
stress uniformly over the entire belt tooth.
Since the betl tooth engages with the pulley groove
without any interference, stress concentration at the
root of the belt tooth can be eliminated

●High Power Trasmission Capacity

1Synchronous Power
- Tooth Shape & Product Code -

Transmission
8.0mm 14.0mm

10.0mm
6.0mm

6.0mm
3.4mm

Belt Pitch Length Belt Pitch Length

Standard Belt Sizes

H8M H14M
Belt Pitch Belt Pitch Belt Pitch
Product Code No of Teeth Length (mm) Product Code No of Teeth Length (mm) Product Code No of Teeth Length (mm)

20
 Synchronous Power
Transmission

Trapezoidal Tooth Timing Belt

Belt Type, Dimensions & Product Code

Standard Dimensions Product Code

Width(mm)

Double Type
No.of Teeth Belt Type
Belt Width(mm)
1Synchronous Power
Transmission

No.of Teeth Belt Width(mm)

Belt Type

XL
G U
Double Type
Belt Width
Belt Length
(DXL) (inch)x10
(inch)x100
G Belt Type

L
G U
Double Type
Belt Width
Belt Length (inch)x100
(DL) (inch)x10
G Belt Type

Double Type
Belt Width
Belt Length (inch)x100
(inch)x10
Belt Type

Belt Length Belt Width

(inch)x10 (inch)x100
Belt Type

Belt Length Belt Width

(inch)x10 (inch)x100
Belt Type

Belt Type No.of Teeth

Double Type Belt Width(mm)

Packaging machine, card reader, textile machine, paper

manufacturing machine, NC lathe, conveyor
Belt Type No.of Teeth

Double Type Belt Width(mm)

For G (rubber ) type, use heat resistant or oil resistant specification when the belts are used in high temperature ( up to 120 °C) or where oil may contaminate the belts.

21
 Synchronous Power
Transmission

Timing Belt G
This synchronous transmission belt eliminates the problems
of chains and gears.
Extra small pitch type fits well for precision equipment and
IT systems.
● Thin, lightweight and superior flexibility of this belt allows compact
design application.
● It enables efficient high speed power transmission
● Low noise operation compared to chain/gear use
● Cost-Efficient

Standard Belt Sizes

1Synchronous Power
Belt Type

Transmission
Tooth Pich
Code(Width)
Product No.of Belt Pich Product No.of Belt Pich Product No.of Belt Pich Product No.of Belt Pich
Code Teeth Length(mm) Code Teeth Length(mm) Code Teeth Length(mm) Code Teeth Length(mm)

Size

This belt is usually made-to-order, however please check with us for stock when you place order.

22
 Synchronous Power
Transmission

Timing Belt G
This synchronous transmission belt eliminates the problems
of chains and gears.
Extra small pitch type fits well for precision equipment and
IT systems.
● Thin, lightweight and superior flexibility of this belt allows compact design
application.
● It enables efficient high speed power transmission
● Low noise operation compared to chain/gear
● Maintenance-free
● l Standard belt can be used in the temperature range between -30°C and
+90°C , and it is also conductive

Standard Belt Sizes

1Synchronous Power

Belt Type
Transmission

Tooth Pich
Code(Width)
Product No.of Belt Pich Product No.of Belt Pich Product No.of Belt Pich Product No.of Belt Pich
Code Teeth Length(mm) Code Teeth Length(mm) Code Teeth Length(mm) Code Teeth Length(mm)

Size

23
 Synchronous Power
Transmission

Timing Belt G

Standard Belt Sizes

1Synchronous Power
Belt Type

Transmission
Tooth Pich
Code(Width)

Product No.of Belt Pich Product No.of Belt Pich

Code Teeth Length(mm) Code Teeth Length(mm)

Size

24
 Synchronous Power
Transmission

Timing Belt U
With its high abrasion resistance and lesser rubber dust dispersion,
polyurethane timing belts are suitable for use in places where clean
environments are required.

● The best for light-duty transmission which requires high precision

● Suitable for paper feeding use because it does not contaminate contact subject.
● Smooth and quiet operation as it is flexible to fit well in small diameter pulleys.
● Made-to-order system enables manufacture of special form orders.

Standard Belt Sizes

1Synchronous Power

Belt Type
Transmission

Tooth Pich
Code(Width)
Product No.of Belt Pich Product No.of Belt Pich Product No.of Belt Pich Product No.of Belt Pich
Code Teeth Length(mm) Code Teeth Length(mm) Code Teeth Length(mm) Code Teeth Length(mm)

Size

25
 Synchronous Power
Transmission

Timing Belt U

Standard Belt Sizes

1Synchronous Power
Belt Type

Transmission
Tooth Pich
Code(Width)
Product No.of Belt Pich Product No.of Belt Pich Product No.of Belt Pich
Code Teeth Length(mm) Code Teeth Length(mm) Code Teeth Length(mm)

Size

26
 Synchronous Power
Transmission

green eco®® Series

Environmental-friendly rubber timing belts with EPDM
compound rubber use.

● Excellent ozone resistance

● Less dispersion of rubber dust

Standard Dimensions and Product Code

1Synchronous Power

Belt Type Standard Dimensions Product Code

Transmission

① 0.08'' (2.032mm)
125MXL12.7
MXL ② ② 0.6mm
Belt Type
③ 0.51mm
③ No. of Teeth Belt Width (mm)

① 5.08mm
120 XL037
XL ② ② 1.0mm
③ 1.27mm
Belt Type
③ Belt Length (inch) x10 Belt Width (inch) x10

① 2.0mm
40S2M160
②
S2M ② 0.6mm
③ 0.76mm Belt Type
③
Belt Width (mm) x10 Nominal Length (mm)

① 3.0mm
100S3M459
②
S3M ② 0.8mm
Belt Type
③ 1.14mm
③ Belt Width (mm) x10 Nominal Length (mm)

① 1.0mm 242ST1.0-3.2
②
ST1.0 ② 0.63mm
③ 0.34mm Belt Type
③
No. of Teeth Belt Width (mm)

① 1.5mm 166ST1.5-4.0
②
ST1.5 ② 0.6mm
③ 0.56mm Belt Type
③
No. of Teeth Belt Width (mm)

① 2.0mm
166ST2.0-4.0
②
ST2.0 ② 0.6mm
③ 0.75mm Belt Type
③
No. of Teeth Belt Width (mm)

① 1/18'' (1.411mm)
510ST55-4.0
②
ST55 ② 0.6mm
③ 0.56mm Belt Type
③
No. of Teeth Belt Width (mm)

① 1/12.5'' (2.032mm)
510ST80-4.0
②
ST80 ② 0.5mm
③ 0.75mm Belt Type
③
No. of Teeth Belt Width (mm)

① 1/12'' (2.117mm)
510ST83-4.0
②
ST83 ② 0.5mm
③ 0.75mm Belt Type
③
No. of Teeth Belt Width (mm)

① 1/9'' (2.822mm)
261ST111-3.2
②
ST111 ② 0.6mm
Belt Type
③ 0.75mm
③
No. of Teeth Belt Width (mm)

27
 Synchronous Power
Transmission

Timing
Timing Pulley
Pulley
Timing belt power transmission systems work the best when
high-accuracy belts and precisely processed pulleys smoothly
mesh with each other.

● Cutting with hob cutter enables good power transmission.

● MBL accepts your request for material, form and processing method.
● Flange is not sold separately as a single item.

Standard Pulley Types & Sizes

1Synchronous Power
Belt Type MXL-Rod shape Belt Type

Transmission
No. of Pulley Product No. of Pulley Product
No. of Teeth Teeth Type Code Teeth Type Code

Material :steel

Belt Type
No. of Pulley
Product Code
Teeth Type

For MXL standard pulley, we stock in rod shape.

Belt Type

No. of Teeth Pulley Type Product Code

Material :steel

28
 Synchronous Power
Transmission

Timing Pulley

Pulley Product Code (Example) 38 XL 037 B

Pulley Type Form
No. of Teeth Belt Width (inch x 100)
Belt Type (Note: belt width is in mm for MXL type)

Add “P” in front of the product code for MXL type

(Ex) P26MXL6.4B

Tooth profile for standard pulleys is in-volute shape complying with ISO
standards.

Standard Pulley Types & Sizes

1Synchronous Power

Belt Type Belt Type

Transmission

No. of Pulley No. of Pulley

Product Code Product Code
Teeth Type Teeth Type

Material :steel

Material :steel Belt Type

No. of Pulley
Product Code
Teeth Type

Material :steel

29
 Synchronous Power
Transmission

LONG-SPAN Timing Belt

(Open-End & Endless)
This belt is for long-span linear drives and light-duty
synchronous transmission and transportation.

● Freer design possible as the length can be extended.

● Rubber Timing Belt

Size Range for Open-End Type

1Synchronous Power
Transmission
x100

Belt Width (inch x100)

Belt Type
Belt Length (m)

For MXL type, belt width is in mm

Belt Length (m)

Belt Type
Belt Width (mm x100)

Size Range for Endless Type

Belt Width (inch x100)

Belt Type
Belt Length (inch x10)

Belt Length (mm)

Belt Type
Belt Width (mm x10)

● Thermosetting Polyurethane Timing Belt

Size Range for Open-End Type

Belt Length (m)

Belt Width (mm)
Belt Type

For XL and L types, belt width is indicated as (inch x100)

Belt Length (m)

Belt Width (mm x10)
Belt Type

30
 2Frictional Forced Power
Transmission Belt
Classical V-Belt / Red label V-Belt ........................P32
Classical V-Belt / Red label V-Belt
for DIN2215 / ISO4184 ....................................P33∼36
MAXSTAR WEDGE V-Belt.......................................P37
MAXSTAR WEDGE V-Belt for RMA / MPTA ..........P38
Narrow V-Belt for DIN7753 / ISO4184 ...................P39
SUPER VS® Belt (Variable Speed Belt) ..................P40
MAXSTAR WEDGE Bushing Pulley .................P41, 42
e-Power® Belt ..........................................................P43
RIBSTAR Belt G (Rubber V-Ribbed Belt) ..............P44
RIBSTAR Belt U (Polyurethane V-Ribbed Belt) ....P45
RIBSTAR Pulley (V-Ribbed Pulley) .........................P46
FLEXSTAR® Belt ......................................................P47
SUPER FLEXSTAR® Belt .........................................P48
FLEXSTAR® Belt J ...................................................P49
POLYMAX Belt .........................................................P50
MB Belt ....................................................................P51
STARROPE®, SUPER STARROPE® .........................P52
PRENE V-ROPE, PRENE HEXAGONAL-ROPE .....P52
Flat Belt ....................................................................P53

31
 Frictional Forced Power
Transmission Belt

Classical V-Belt/ Red label V-Belt

This type is most commonly used as a means for power transmission.
Therefore, it is economic and available in the market. Also, it is easily
replaced.
● Our “SET FREE®” system for multiple belt usage is very effective to reduce
dimensional differences of each belt.
● Red label V-Belt is a heavy-duty power transmission belt, which has heat,
oil and flex resistance as well as a high antistatic property

Product Code A-50

Belt Type Belt Code (inch)
● Belt code indicates effective pitch length of the belt in inches.
(For M type, length is outer circumference)
Cross-Sectional Dimensions

E
D
C

Power Transmission Belt

A B

2Frictional Forced
M

(Note) Above dimensions are nominal values.

Standard Belt Sizes

32
 Frictional Forced Power
Transmission Belt

Classical V-Belts for DIN 2215/ISO4184

(Wrapped Type
Type // Raw
Raw Edge
Edge Cogged
Cogged Type)
Type)
Widely-used power transmission belt.
Cost efficient, readily available, easily changeable
Product Code A-40
Belt Type Belt Code (inch)
● Belt code is nomial length in inch

40.0mm
Cross-Sectional Dimensions (11/2")

32.0mm
(11/4")
22.0mm
(7/8")
17.0mm
13.0mm (21/32")
(1/2")
10mm E(40) 25mm
D(32) 20mm (1")
C(22) 14mm (3/4")
A(13) B(17) 11mm (9/16")
9mm CX
Z(10) (11/32") BX (7/16")
ZX
6mm AX
Power Transmission Belt
2Frictional Forced

Standard Belt Sizes

Z(10), ZX

Belt Code Inside Length Datum Length Belt Code Inside Length Datum Length
Li (mm) Ld (mm) Li (mm) Ld (mm)
20 515 537 38.5 975 997
20.5 525 547 39 990 1012
21 530 552 39.5 1000 1022
21.5 550 572 40 1016 1038
22 560 582 40.5 1030 1052
22.5 575 597 41 1041 1063
23 585 607 41.5 1050 1072
23.5 600 622 42 1060 1082
24 610 632 42.25 1075 1097
24.5 620 642 42.5 1080 1102
25 630 652 43 1090 1112
25.5 650 672 43.5 1105 1127
26 660 682 44 1120 1142
26.5 670 692 45 1140 1162
27 685 707 45.5 1150 1172
27.5 700 722 46 1165 1187
28 710 732 47 1194 1216
28.5 725 747 47.5 1215 1237
29 730 752 48 1225 1247
29.5 750 772 49 1250 1272
30 765 787 50 1270 1292
30.5 775 797 51 1295 1317
31 790 812 51.5 1310 1332
31.5 800 822 52 1320 1342
32 820 842 52.5 1330 1352
32.5 825 847 53 1346 1368
33 840 862 54 1371 1393
33.5 850 872 55 1400 1422
34 865 887 56 1422 1444
34.5 875 897 57 1450 1472
35 890 912 58 1475 1497
35.5 900 922 59 1500 1522
36 915 937 60 1525 1547
36.5 925 947
37 940 962
Size range : 18.5" - 93"
37.5 950 972
38 965 987

All dimentions are nominal values.

: Available sizes for raw edge cogged belt ZX

33
 Frictional Forced Power
Transmission Belt

Classical V-Belts for DIN 2215/ISO4184

A(13), AX
Inside Datum Inside Datum Inside Datum Inside Datum
Belt Code Length Length Belt Code Length Length Belt Code Length Length Belt Code Length Length
Li(mm) Ld(mm) Li(mm) Ld(mm) Li(mm) Ld(mm) Li(mm) Ld(mm)
20 508 538 57 1450 1480 94 2388 2418 165 4200 4230
21 535 565 58 1475 1505 95 2413 2443 167 4250 4280
22 560 590 59 1500 1530 96 2438 2468 170 4318 4348
23 585 615 60 1525 1555 97 2464 2494 173 4394 4424
24 610 640 61 1550 1580 98 2500 2530 176 4470 4500
25 630 660 62 1575 1605 99 2515 2545 180 4572 4602
26 660 690 63 1600 1630 100 2540 2570 185 4700 4730
27 686 716 64 1625 1655 101 2565 2595 187 4750 4780
28 710 740 65 1650 1680 102 2591 2621 190 4825 4855
29 730 760 66 1676 1706 103 2616 2646 195 4950 4980

Power Transmission Belt

30 767 797 67 1700 1730 104 2650 2680 197 5000 5030

2Frictional Forced
31 787 817 68 1725 1755 105 2667 2697 200 5080 5110
32 813 843 69 1750 1780 106 2692 2722
33 838 868 70 1775 1805 107 2725 2755
34 864 894 71 1800 1830 108 2743 2773
35 889 919 72 1825 1855 109 2769 2799
36 914 944 73 1854 1884 110 2800 2830
37 940 970 74 1880 1910 112 2845 2875
38 965 995 75 1900 1930 115 2921 2951
39 990 1020 76 1930 1960 116 2946 2976
40 1016 1046 77 1956 1986 118 3000 3030
41 1041 1071 78 1980 2010 120 3048 3078
42 1060 1090 79 2000 2030 122 3100 3130 Size range : 20" - 360"
43 1100 1130 80 2032 2062 124 3150 3180
44 1120 1150 81 2060 2090 125 3175 3205
45 1143 1173 82 2083 2113 128 3250 3280
46 1168 1198 83 2110 2140 130 3300 3330
47 1200 1230 84 2134 2164 134 3400 3430
48 1220 1250 85 2160 2190 135 3425 3455
49 1250 1280 86 2180 2210 136 3454 3484
50 1270 1300 87 2210 2240 140 3550 3580
51 1300 1330 88 2240 2270 144 3658 3688
52 1320 1350 89 2260 2290 150 3810 3840
53 1350 1380 90 2286 2316 150 3810 3840
54 1375 1405 91 2310 2340 158 4000 4030
55 1400 1430 92 2337 2367 160 4064 4094
56 1422 1452 93 2360 2390 162 4115 4145

All dimentions are nominal values.

: Available sizes for raw edge cogged belt AX

B(17), BX
Inside Datum Inside Datum Inside Datum Inside Datum Inside Datum
Belt Code Length Length Belt Code Length Length Belt Code Length Length Belt Code Length Length Belt Code Length Length
Li(mm) Ld(mm) Li(mm) Ld(mm) Li(mm) Ld(mm) Li(mm) Ld(mm) Li(mm) Ld(mm)
20 510 553 55 1400 1443 92 2337 2380 138 3500 3543 225 5700 5743
21 535 578 56 1425 1468 93 2360 2403 140 3550 3593 228 5800 5843
22 560 603 57 1450 1493 94 2388 2431 142 3600 3643 230 5850 5893
23 585 628 58 1475 1518 95 2413 2456 144 3658 3701 232 5893 5936
24 615 658 59 1500 1543 96 2438 2481 145 3675 3718 236 6000 6043
25 630 673 60 1525 1568 97 2465 2508 146 3700 3743 238 6045 6088
26 660 703 61 1550 1593 98 2500 2543 148 3750 3793 240 6096 6139
27 686 729 62 1575 1618 99 2515 2558 150 3810 3853 245 6225 6268
28 710 753 63 1600 1643 100 2540 2583 152 3861 3904 248 6300 6343
29 735 778 64 1625 1668 101 2565 2608 154 3912 3955 250 6350 6393
30 762 805 65 1650 1693 102 2600 2643 155 3937 3980 255 6475 6518
29 735 778 66 1675 1718 103 2616 2659 156 3950 3993 260 6600 6643
30 762 805 67 1700 1743 104 2650 2693 158 4000 4043 264 6700 6743
31 785 828 68 1725 1768 105 2667 2710 160 4065 4108 268 6800 6843
32 813 856 69 1750 1793 106 2700 2743 162 4115 4158 270 6850 6893
33 838 881 70 1775 1818 107 2718 2761 164 4165 4208 276 7000 7043
34 865 908 71 1800 1843 108 2750 2793 165 4200 4243 280 7100 7143
35 889 932 72 1825 1868 110 2800 2843 166 4215 4258 290 7360 7403
36 915 958 73 1850 1893 112 2845 2888 169 4300 4343 300 7620 7663
37 940 983 74 1880 1923 113 2870 2913 170 4318 4361 310 7875 7918
38 965 1008 75 1900 1943 114 2900 2943 173 4394 4437 320 8125 8168
39 991 1034 76 1930 1973 115 2921 2964 175 4450 4493 330 8375 8418
40 1016 1059 77 1950 1993 116 2950 2993 177 4500 4543 340 8640 8683
41 1040 1083 78 1981 2024 117 2972 3015 180 4572 4615 350 8900 8943
42 1060 1103 79 2000 2043 118 3000 3043 185 4700 4743 360 9150 9193
43 1090 1133 80 2032 2075 120 3048 3091 188 4775 4818 370 9400 9443
44 1120 1163 81 2060 2103 122 3099 3142 190 4826 4869 380 9650 9693
45 1150 1193 82 2083 2126 124 3150 3193 192 4875 4918 390 9900 9943
46 1175 1218 83 2100 2143 125 3175 3218 195 4953 4996 400 10160 10203
47 1200 1243 84 2134 2177 126 3200 3243 197 5000 5043
48 1215 1258 85 2160 2203 128 3250 3293 200 5080 5123
49 1250 1293 86 2200 2243 130 3300 3343 204 5182 5225
50 1275 1318 87 2210 2253 132 3350 3393 205 5200 5243 Size range : 20" - 660"
51 1300 1343 88 2240 2283 133 3375 3418 210 5334 5377
52 1320 1363 89 2260 2303 134 3400 3443 215 5450 5493
53 1350 1393 90 2286 2329 135 3425 3468 218 5540 5583
54 1372 1415 91 2300 2343 136 3450 3493 220 5600 5643

All dimentions are nominal values.

: Available sizes for raw edge cogged belt BX

34
 Frictional Forced Power
Transmission Belt

Classical V-Belts for DIN 2215/ISO4184

C(22), CX
Inside Datum Inside Datum Inside Datum Inside Datum Inside Datum
Belt Code Length Length Belt Code Length Length Belt Code Length Length Belt Code Length Length Belt Code Length Length
Li(mm) Ld(mm) Li(mm) Ld(mm) Li(mm) Ld(mm) Li(mm) Ld(mm) Li(mm) Ld(mm)
30 762 814 67 1700 1752 104 2642 2694 162 4115 4167 270 6858 6910
31 787 839 68 1725 1777 105 2667 2719 164 4166 4218 275 6985 7037
32 813 865 69 1750 1802 106 2692 2744 168 4267 4319 280 7100 7152
33 838 890 70 1775 1827 107 2718 2770 170 4318 4370 290 7366 7418
Power Transmission Belt

34 864 916 71 1800 1852 108 2750 2802 173 4390 4442 300 7600 7652
2Frictional Forced

35 889 941 72 1829 1881 110 2800 2852 175 4445 4497 320 8130 8182
36 914 966 73 1854 1906 111 2819 2871 177 4500 4552 330 8380 8432
37 940 992 74 1880 1932 112 2845 2897 180 4572 4624 340 8636 8688
38 950 1002 75 1900 1952 113 2870 2922 183 4648 4700 350 8900 8952
39 975 1027 76 1930 1982 114 2896 2948 185 4700 4752 360 9144 9196
40 1000 1052 77 1956 2008 115 2921 2973 187 4750 4802 370 9400 9452
41 1030 1082 78 1981 2033 116 2950 3002 190 4825 4877 380 9650 9702
42 1075 1127 79 2000 2052 118 3000 3052 195 4950 5002 400 10160 10212
43 1090 1142 80 2032 2084 120 3050 3102 197 5000 5052 415 10540 10592
44 1120 1172 81 2060 2112 122 3100 3152 200 5080 5132 434 11000 11052
45 1150 1202 82 2083 2135 123 3125 3177 202 5131 5183 473 12000 12052
46 1175 1227 83 2108 2160 124 3150 3202 204 5182 5234 492 12500 12552
47 1200 1252 84 2135 2187 125 3175 3227 205 5207 5259 512 13000 13052
48 1220 1272 85 2159 2211 126 3200 3252 210 5334 5386 550 14000 14052
49 1250 1302 86 2184 2236 128 3250 3302 215 5461 5513 590 15000 15052
50 1270 1322 87 2210 2262 129 3270 3322 220 5600 5652
51 1295 1347 88 2240 2292 130 3300 3352 222 5639 5691
52 1320 1372 89 2261 2313 132 3350 3402 224 5690 5742
53 1350 1402 90 2286 2338 134 3400 3452 225 5715 5767
54 1375 1427 91 2311 2363 136 3450 3502 228 5791 5843
55 1400 1452 92 2337 2389 138 3500 3552 230 5842 5894
56 1425 1477 93 2360 2412 140 3550 3602 235 5970 6022
Size range : 30" - 660"
57 1450 1502 94 2388 2440 142 3600 3652 238 6045 6097
58 1475 1527 95 2413 2465 144 3658 3710 240 6096 6148
59 1500 1552 96 2438 2490 146 3700 3752 246 6250 6302
60 1525 1577 97 2465 2517 148 3750 3802 248 6300 6352
61 1550 1602 98 2500 2552 150 3810 3862 250 6350 6402
62 1575 1627 99 2525 2577 152 3861 3913 256 6500 6552
63 1600 1652 100 2540 2592 154 3912 3964 258 6553 6605
64 1625 1677 101 2560 2612 155 3937 3989 260 6600 6652
65 1650 1702 102 2591 2643 158 4000 4052 264 6700 6752
66 1675 1727 103 2616 2668 160 4064 4116 268 6800 6852

All dimentions are nominal values.

: Available sizes for raw edge cogged belt CX

35
 Frictional Forced Power
Transmission Belt

Classical V-Belts for DIN 2215/ISO4184

D(32) E(40)
Inside Datum Inside Datum Inside Datum Inside Datum Inside Datum
Belt Code Length Length Belt Code Length Length Belt Code Length Length Belt Code Length Length Belt Code Length Length
Li(mm) Ld(mm) Li(mm) Ld(mm) Li(mm) Ld(mm) Li(mm) Ld(mm) Li(mm) Ld(mm)
100 2540 2615 168 4267 4342 265 6725 6800 144 3650 3732 365 9275 9357
103 2616 2691 170 4320 4395 268 6800 6875 180 4575 4657 370 9400 9482
104 2650 2725 172 4370 4445 270 6850 6925 185 4700 4782 375 9525 9607
105 2675 2750 173 4390 4465 275 6985 7060 190 4825 4907 380 9650 9732

Power Transmission Belt

108 2750 2825 174 4420 4495 280 7100 7175 195 4950 5032 385 9775 9857

2Frictional Forced
110 2800 2875 175 4450 4525 285 7250 7325 200 5080 5162 390 9900 9982
112 2850 2925 176 4470 4545 290 7375 7450 205 5200 5282 395 10025 10107
115 2925 3000 178 4525 4600 295 7500 7575 210 5300 5382 400 10160 10242
118 3000 3075 180 4570 4645 300 7620 7695 220 5600 5682 405 10300 10382
120 3048 3123 182 4620 4695 310 7875 7950 225 5715 5797 410 10400 10482
122 3100 3175 184 4675 4750 330 8380 8455 230 5850 5932 415 10550 10632
124 3150 3225 185 4700 4775 350 8900 8975 235 5970 6052 420 10670 10752
126 3200 3275 186 4725 4800 370 9400 9475 240 6100 6182 425 10800 10882
128 3250 3325 188 4775 4850 390 9900 9975 245 6225 6307 430 10925 11007
130 3300 3375 190 4825 4900 400 10160 10235 250 6350 6432 435 11050 11132
132 3350 3425 192 4875 4950 420 10670 10745 255 6475 6557 440 11200 11282
134 3400 3475 194 4925 5000 420 10670 10745 260 6600 6682 445 11300 11382
135 3425 3500 195 4950 5025 450 11430 11505 265 6730 6812 450 11430 11512
136 3450 3525 198 5025 5100 470 11950 12025 270 6850 6932 455 11550 11632
138 3500 3575 200 5080 5155 500 12700 12775 275 6985 7067 460 11700 11782
140 3550 3625 205 5200 5275 540 13720 13795 280 7100 7182 465 11800 11882
142 3600 3675 210 5330 5405 550 14000 14075 285 7250 7332 470 11950 12032
144 3658 3733 215 5450 5525 600 15240 15315 290 7375 7457 475 12050 12132
146 3700 3775 217 5500 5575 630 16000 16075 295 7500 7582 480 12190 12272
148 3750 3825 220 5600 5675 660 16760 16835 300 7620 7702 485 12325 12407
150 3810 3885 225 5715 5790 305 7750 7832 490 12500 12582
152 3860 3935 228 5790 5865 310 7875 7957 495 12575 12657
154 3900 3975 230 5850 5925 315 8000 8082 500 12700 12782
155 3925 4000 235 5970 6045 320 8125 8207 540 13720 13802
156 3950 4025 236 6000 6075 325 8250 8332 600 15240 15322
Size range : 79" - 660"
158 4000 4075 238 6045 6120 330 8380 8462 660 16760 16842
160 4060 4135 240 6096 6171 335 8500 8582
162 4115 4190 245 6225 6300 340 8650 8732
164 4165 4240 248 6300 6375 345 8750 8832
165 4200 4275 250 6350 6425 350 8900 8982
166 4225 4300 255 6475 6550 355 9000 9082
167 4250 4325 260 6600 6675 360 9150 9232

All dimentions are nominal values. All dimentions are nominal values.

36
 Frictional Forced Power
Transmission Belt

MAXSTAR WEDGE V-Belt

With its unique narrow width, this V-Belt has high power
transmission capability.

● Energy-saving and compact design application

● Possible to operate with maximum speed of 40m/sec
● Excellent heat resistance and antistatic property
● Our “set-free” system for multiple belt usage is very effective to reduce
dimensional differences of each belt.
● We standardize easy-to-install bussing types as our wedge pulley.

Product Code
5V- 2000
Belt Type

Belt Code = Effective Belt Length (inch) x10

Comparison with Standard V-Belt
Power Transmission Belt
2Frictional Forced

Standard Belt Sizes

Product Code Effective Belt Belt Pitch Product Code Effective Belt Belt Pitch Product Code Effective Belt Belt Pitch
Length (mm) Length (mm) Length (mm) Length (mm) Length (mm) Length (mm)

:C

37
 Frictional Forced Power
Transmission Belt

MAXSTAR WEDGE V-Belt for RMA/MPTA

Unique narrow V belt with high power transmission capability
Suitable for energy-saving / compact design and can be used for high-speed
operation up to 40m /second

Product Code
5V-2500
Belt Type Belt Code = Effective Belt Length (inch) x10

Cross-Sectional Dimensions
25.5mm
(1")

16.0mm
(5/8") 16.6mm

9.5mm
(3/8")
9.9
mm 8V 23.0mm
(7/8")

3V 3VX
5V 13.5mm 5VX 13.5mm

Power Transmission Belt

8.0mm 8.7mm
(5/16")
(17/32")

2Frictional Forced
Standard Belt Sizes

3V . 3VX 5V . 5VX 8V
Effective Effective Effective
Belt Code Outside Length 3V 3VX Belt Code Outside Length 5V 5VX Belt Code Outside Length 8V
La (mm) La (mm) La (mm)
250 635 ○ ○ 500 1270 ○ ○ 1000 2540 ○
265 673 ○ ○ 530 1346 ○ ○ 1060 2692 ○
280 711 ○ ○ 560 1422 ○ ○ 1120 2845 ○
300 762 ○ ○ 600 1524 ○ ○ 1180 2997 ○
315 800 ○ ○ 630 1600 ○ ○ 1250 3175 ○
335 851 ○ ○ 670 1702 ○ ○ 1320 3353 ○
355 902 ○ ○ 710 1803 ○ ○ 1400 3556 ○
375 953 ○ ○ 750 1905 ○ ○ 1500 3810 ○
400 1016 ○ ○ 800 2032 ○ ○ 1600 4064 ○
425 1080 ○ ○ 850 2159 ○ ○ 1700 4318 ○
450 1143 ○ ○ 900 2286 ○ ○ 1800 4572 ○
475 1207 ○ ○ 950 2413 ○ ○ 1900 4826 ○
500 1270 ○ ○ 1000 2540 ○ ○ 2000 5080 ○
530 1346 ○ ○ 1060 2692 ○ ○ 2120 5385 ○
560 1422 ○ ○ 1120 2845 ○ ○ 2240 5690 ○
600 1524 ○ ○ 1180 2997 ○ ○ 2360 5994 ○
630 1600 ○ ○ 1250 3175 ○ ○ 2500 6350 ○
670 1702 ○ ○ 1320 3353 ○ ○ 2650 6731 ○
710 1803 ○ ○ 1400 3556 ○ ○ 2800 7112 ○
750 1905 ○ ○ 1500 3810 ○ ○ 3000 7620 ○
800 2032 ○ ○ 1600 4064 ○ ○ 3150 8001 ○
850 2159 ○ ○ 1700 4318 ○ ○ 3350 8509 ○
900 2286 ○ ○ 1800 4572 ○ ○ 3550 9017 ○
950 2413 ○ ○ 1900 4826 ○ ○ 3750 9525 ○
1000 2540 ○ ○ 2000 5080 ○ ○ 4000 10160 ○
1060 2692 ○ ○ 2120 5385 ○ ○ 4250 10795 ○
1120 2845 ○ ○ 2240 5690 ○ ○ 4500 11430 ○
1180 2997 ○ ○ 2360 5994 ○ ○ 4750 12065 ○
1250 3175 ○ ○ 2500 6350 ○ ○ 5000 12700 ○
1320 3353 ○ ○ 2650 6731 ○ ○ 5600 14224 ○
1400 3556 ○ ○ 2800 7112 ○ 6000 15240 ○
3000 7620 ○
3150 8001 ○
3350 8509 ○
3550 9017 ○

All dimentions are nominal values.

38
 Frictional Forced Power
Transmission Belt

Narrow
Narrow V-Belt
V-Belt for
for DIN
DIN 7753/ISO4184
7753/ISO4184
Suitable for energy-saving / compact design
Reduces maintenance costs

Product Code SPZ-1000

Belt Type Belt Code (mm)
∗ Belt code = belt effective length (mm)

Cross-Sectional Dimensions
9.7mm 16.3mm 22.0mm
12.7mm

SPB SPC 18.0mm

SPZ 8.0mm SPA
10.0mm SPBX 13.0mm SPCX
SPZX SPAX
Power Transmission Belt
2Frictional Forced

Standard Belt Sizes

SPX (SPZX) SPA (SPAX) SPB (SPBX) SPC (SPCX)

Pitch Length Pitch Length Pitch Length Pitch Length Pitch Length Pitch Length Pitch Length Pitch Length Pitch Length Pitch Length Pitch Length Pitch Length
LW (mm) LW (mm) LW (mm) LW (mm) LW (mm) LW (mm) LW (mm) LW (mm) LW (mm) LW (mm) LW (mm) LW (mm)
487 1112 1937 3450 732 1407 2360 1250 2680 4870 2000 4380
512 1120 1987 3550 735 1410 2373 1260 2700 5000 2120 4400
562 1137 2000 3660 742 1425 2382 1320 2720 5070 2240 4420
587 1140 2030 3750 757 1432 2407 1340 2750 5300 2280 4445
612 1162 2037 4000 760 1457 2410 1400 2800 5380 2335 4450
630 1180 2050 4500 782 1482 2432 1410 2820 5500 2360 4500
637 1187 2060 800 1485 2482 1500 2840 5600 2400 4530
650 1200 2082 807 1500 2500 1510 2900 5680 2413 4650
655 1202 2087 832 1507 2532 1590 2990 5800 2425 4720
662 1212 2120 850 1532 2550 1600 3000 5990 2500 4750
665 1222 2137 857 1557 2568 1690 3070 6000 2550 4850
670 1237 2150 860 1582 2582 1700 3150 6300 2580 4900
687 1250 2160 882 1600 2600 1750 3170 6340 2600 4970
690 1262 2187 885 1607 2607 1800 3175 6700 2650 5000
710 1270 2200 900 1632 2632 1850 3200 6720 2700 5030
722 1282 2240 907 1657 2650 1900 3238 2720 5070
737 1287 2262 932 1682 2682 1950 3250 2750 5200
750 1300 2280 950 1700 2732 2000 3280 2770 5300
760 1312 2287 957 1707 2773 2020 3328 2800 5330
762 1320 2300 967 1732 2782 2030 3340 2840 5400
772 1337 2337 982 1757 2800 2060 3350 2900 5500
787 1340 2360 1000 1782 2832 2120 3400 2950 5600
800 1347 2387 1007 1785 2847 2131 3412 3000 5700
812 1362 2400 1032 1800 2850 2137 3425 3050 6000
825 1387 2410 1057 1807 2882 2150 3450 3100 6200
835 1400 2437 1060 1832 2900 2180 3500 3150 6300
837 1412 2450 1082 1837 2932 2200 3550 3200 6480
850 1420 2487 1090 1857 2962 2240 3650 3220 6500
862 1437 2500 1107 1882 2982 2264 3675 3320 6700
875 1462 2540 1120 1900 3000 2280 3700 3350
885 1487 2580 1132 1907 3032 2300 3750 3375
887 1500 2600 1157 1932 3082 2310 3770 3420
900 1512 2637 1180 1957 3132 2320 3800 3430
912 1520 2650 1182 1982 3150 2330 3850 3450
925 1537 2670 1200 2000 3182 2360 3870 3500
937 1560 2687 1207 2032 3282 2390 3875 3520
940 1562 2690 1210 2057 3350 2391 4000 3550
950 1587 2700 1232 2082 3382 2410 4060 3600
962 1600 2712 1235 2100 3482 2425 4100 3620
987 1612 2720 1250 2120 3500 2430 4120 3670
1000 1637 2737 1257 2132 3550 2450 4250 3700
1005 1662 2760 1272 2157 3650 2473 4260 3750
1010 1687 2800 1282 2182 3750 2500 4296 3770
1012 1700 2840 1295 2200 3870 2518 4310 3800
1024 1737 2900 1300 2207 4000 2522 4318 3810
1037 1762 3000 1307 2232 4120 2530 4370 3970
1047 1787 3050 1320 2240 4250 2550 4500 4000
1060 1800 3070 1332 2260 4300 2575 4560 4050
1077 1812 3150 1357 2282 4500 2580 4600 4100
1080 1837 3170 1367 2300 4600 2600 4620 4200
1087 1862 3200 1382 2307 4750 2640 4720 up to 4250 up to
1100 1887 3250 1385 2330 4865 2650 4750 10000 4300 12500
1110 1900 3350 1400 2332 5000 2670 4820 4350
All dimentions are nominal values.
: Available sizes for raw edge cogged belt SPZX, SPAX, SPBX, SPCX
39
 Frictional Forced Power
Transmission Belt

SUPER VS®® Belt (Variable Speed Belt)

Changes in speed can be accurately, smoothly and quietly transmitted
from low to high speed.
High precision and transmission efficiency as well as excellent durability.
Almost no elongation. Excellent oil, heat and lateral pressure resistance.
Specially for high performance and high quality transmission systems.

Cross-Sectional Diagram Product Code

a a(mm) b(mm) θ(mm) SUPER VS 16-8-700

30 10 22 Belt Outer Length (mm)
37 12 22 Belt Thickness (mm)
12 5 22
16 6 22 Belt Type Belt Top Width (mm)
b
22 8 22
θ 10 5 22
12 6 22
16 8 22
20 10 22 ISO Code RMA Code

Power Transmission Belt

20 12 22
SUPER VS 22-8-700 = 14 22 V 270

2Frictional Forced
Belt Pitch Length
Variable Speed Belt
Pulley Groove Angle (22°)
Belt Type Belt Top Width (14×1/16 inches)
Belt Outer Length (mm)
Belt Top Width (mm) Belt Thickness (mm)

Standard Belt Sizes

ISO Code RMA Code ISO Code RMA Code ISO Code RMA Code ISO Code*1 ISO Code*2 ISO Code*3

30-10-668 37-12-855 2322V329 22-8-615 1422V235 10-5-450 16-8-600 20-10-1600

30-10-723 1922V277 37-12-945 2322V364 22-8-625 1422V240 10-5-475 16-8-625 20-10-1650
30-10-733 1922V282 37-12-995 2322V384 22-8-648 1422V250 10-5-500 16-8-650 20-10-1700
30-10-773 1922V298 37-12-1030 2322V396 22-8-700 1422V270 10-5-525 16-8-675 20-10-1750
30-10-783 1922V302 37-12-1090 2322V421 22-8-755 1422V290 10-5-550 16-8-700 20-10-1800
30-10-813 1922V313 37-12-1120 2322V434 22-8-780 1422V300 10-5-575 16-8-725 20-10-1850
30-10-813 1922V314 37-12-1140 2322V441 22-8-855 1422V330 10-5-600 16-8-750 20-10-1900
30-10-838 1922V321 37-12-1190 2322V461 22-8-880 1422V340 10-5-625 16-8-775 20-10-1950
30-10-863 1922V332 37-12-1240 2322V481 22-8-930 1422V360 10-5-650 16-8-800 20-10-2000
30-10-878 1922V338 37-12-1255 2322V486 22-8-1030 1422V400 10-5-675 16-8-825 20-12-750
30-10-943 1922V363 37-12-1345 2322V521 22-8-1085 1422V420 10-5-700 16-8-850 20-12-800
30-10-988 1922V381 37-12-1395 2322V541 22-8-1135 1422V440 10-5-725 16-8-875 20-12-850
30-10-998 1922V386 37-12-1545 2322V601 22-8-1185 1422V460 10-5-750 16-8-900 20-12-900
30-10-1043 1922V403 37-12-1595 2322V621 22-8-1200 1422V466 12-6-500 16-8-925 20-12-950
30-10-1078 1922V417 37-12-1700 2322V661 22-8-1210 1422V470 12-6-525 16-8-950 20-12-1000
30-10-1098 1922V426 37-12-1750 2322V681 22-8-1235 1422V480 12-6-550 16-8-975 20-12-1050
30-10-1143 1922V443 37-12-1800 2322V701 22-8-1390 1422V540 12-6-575 16-8-1000 20-12-1100
30-10-1173 1922V454 37-12-1850 2322V721 22-8-1540 1422V600 12-6-600 20-10-750 20-12-1150
30-10-1188 1922V460 37-12-2055 2322V801 22-8-1690 1422V660 12-6-625 20-10-800 20-12-1200
30-10-1248 1922V484 37-12-2120 2322V826 22-8-1845 1422V720 12-6-650 20-10-850 20-12-1250
30-10-1353 1922V526 37-12-2170 2322V846 22-8-1995 1422V780 12-6-675 20-10-900 20-12-1300
30-10-1398 1922V544 37-12-2270 2322V886 12-6-700 20-10-950 20-12-1350
30-10-1553 1922V604 37-12-2360 2322V921 12-6-725 20-10-1000 20-12-1400
30-10-1618 1922V630 12-5-451 7.522V173 12-6-750 20-10-1050 20-12-1450
30-10-1663 1922V646 12-5-501 7.522V193 12-6-775 20-10-1100 20-12-1500
30-10-1708 1922V666 12-5-551 7.522V212 12-6-800 20-10-1150 20-12-1550
30-10-1758 1922V686 12-5-571 7.522V220 12-6-825 20-10-1200 20-12-1600
30-10-1813 1922V706 16-6-513 1022V196 12-6-850 20-10-1250 20-12-1650
30-10-1848 1922V721 16-6-548 1022V210 12-6-875 20-10-1300 20-12-1700
30-10-1863 1922V726 16-6-573 1022V220 12-6-900 20-10-1350 20-12-1750
30-10-1928 1922V751 16-6-578 1022V223 12-6-925 20-10-1400 20-12-1800
30-10-1938 1922V756 16-6-628 1022V247 12-6-950 20-10-1450 20-12-1850
30-10-2068 1922V806 12-6-975 20-10-1500 20-12-1900
30-10-2168 1922V846 12-6-1000 20-10-1550 20-12-1950
20-12-2000
Note 1) *1, *2, *3 are only in ISO Code.
Note 2) Please contact us for sizes beyond the standard size.

40
 Frictional Forced Power
Transmission Belt

MAXSTAR WEDGE Bushing Pulley

For all wedge pulleys, we adopt a “bushing system” for easy
attachment and removal from the shaft with one spanner.

● Long shaft life as it does not damage the shaft and shaft hole
● No need for additional processing of the shaft hole
● Easy centering and smooth positional change of rotating body such as the pulley
● Possible weight reduction of pulley as small bore width can be applied

Bushing Pulley Product Code

450-5V-3-R1
Pulley No. of Grooves
Diameter
Belt Type Bushing Type

Application chart for MB Bushing on MAXSTAR WEDGE Pulley

Belt Type Belt Type Belt Type

Standard Pulley No.of Grooves Standard Pulley No.of Grooves Standard Pulley No.of Grooves
Diameter/Diameter Diameter/Diameter Diameter/Diameter
Code(mm) Code(mm) Code(mm)
Power Transmission Belt
2Frictional Forced

● How to mount onto the shaft

Mounting bushing pulley is easy
1 2 3 even from the opposite side.

1 Fasten bolts evenly

Place the bushing in the Attach the bushing pulley Fasten tight with tightening
2 Wear protective gear such as gloves while mounting and removing the
pulley and loosen bolts by onto the shaft (it should bolts and fitting is completed.
pulley. Also, before starting any work, switch off the power and ensure
hand fit smoothly.)
that machine is completely stopped.

● How to detach from the shaft ● Bolt Tightening Torque

1 2 3

Remove tightening bolts Screw the bolts into the Remove the bushing pulley
taps for flange removal from the shaft

41
 Frictional Forced Power
Transmission Belt

Number of Required Belts and Pulley Width

MB Bushing Size Table

Power Transmission Belt

2Frictional Forced

42
 Frictional Forced Power
Transmission Belt

e-Power®® V-Belt
This type has enhanced flexibility over standard V-Belts.
Due to this flexibility, it reduces the energy loss from bending
stress and thus is more efficient and energy-saving.

● It saves electricity.
● It is compatible with exisiting pulley designs.
● Compact design application.
● It has longer operating life.
● You can choose from 2 types depending on intended use :
Raw Edge Cogged type and Wrapped Notched type

Raw Edge Cogged Type Wrapped Notched Type

Power Transmission Belt
2Frictional Forced

For the cogged type, to enhance flexibility, wave shape dents For the Notched type, to enhance flexibility, notches are
are added on the bottom of the Raw Edge Belt. added across the bottom of the Wrapped V-Belt.

Product Code

AX-50 A-50

Belt Type Belt Code (inch) Belt Type Belt Code (inch)

● Belt code indicates belt effective pitch length in inches ● Belt code indicates belt effective pitch length in inches

Cross-Sectional Dimensions

Above are nominal values.

Standard Belt Sizes

Nominal Length Nominal Length

AX 20~180 A 30~200
BX 25~270 B 30~200
CX 40~270 C 45~200

43
 Frictional Forced Power
Transmission Belt

RIBSTAR Belt G (Rubber V-Ribbed Belt)

This belt combines the properties of the V-Belt’s high power
transmission capability and the Flat Belt flexibility.
● High-efficiency operation at high speed
● It can be used on a small diameter pulley because of its enhanced flexibility.
● Excellent heat resistance and abrasion resistance
● Compact design application.
● Little belt vibration.
Product Code (Example) For PK type, the metric system is used

320 J 5 5 PK 1500
No. of Ribs
Belt Type No. of Ribs
Belt Effective Length (inch) x10 Belt Type Belt Effective
Length (mm)
∗ Effective Length : The effective outer perimeter

Cross-Sectional Diagram

N:No.of Ribs

Power Transmission Belt

2Frictional Forced
Standard Sizes for Industrial RIBSTAR Belt

Product Code Effective Length (mm) Product Code Effective Length (mm) Product Code Effective Length (mm)

signifies made-to-order size.

44
 Frictional Forced Power
Transmission Belt

RIBSTAR Belt U (Polyurethane V-Ribbed Belt)

This polyurethane belt combines the features of both V-Belt and Flat Belt.
● Usable on small diameter pulleys (minimumφ20mm) because of its enhanced flexibility
with nylon cord.
● Excellent flex fatigue resistance.
● Smooth revolution with little vibration.
● It withstands high-speed operation
● Excellent abrasion, oil and ozone resistance
Product Code (Example)
180 - JBT - 4
No. of Ribs (4 ribs)
Belt Type
Belt Length :
Pitch Length (inch) x 10

Dimensions

Sectional Size
Rib Pitch
Rib Angle
Rib Height
Rib Bottom Thickness
Power Transmission Belt

Total Thickness
2Frictional Forced

Belt Width

Standard Belt Sizes for JBT Type

Pitch Length(mm) Pitch Length(mm) Pitch Length(mm) Pitch Length(mm)

Form and Structure of Pulley Groove

Groove Dimensions for RIBSTAR Pulley

45
 Frictional Forced Power
Transmission Belt

RIBSTAR Pulley
Except for a few sizes, RIBSTAR pulleys adopt the “bushing
system” for easy attachment and removal as well as positioning
of pulley onto the shaft.

Pulley Product Code (Example)

PK - 160 - 5 - 1210
Groove Form Bushing
Product
Diameter Code : Code
Effective Outer Diameter (mm) No. of Grooves

Bore Outer Diameter

Effective Outer Diameter
Pitch Diameter

Pulley Groove Dimensions

Power Transmission Belt

2Frictional Forced
Hg Reference Value

Pulley Sizes and Relevant Bushing Product Code

Bushing Bushing Bushing Bushing Bushing Bushing

(Outer Diameter) Product Code Product Code Product Code Product Code Product Code Product Code

Up to 30m/sec of pulley rim speed is enabled. Please do not exceed 30m/sec.

46
 Frictional Forced Power
Transmission Belt

FLEXSTAR®® Belt
Because of its large power transmission capacity,
compact design application and cost reduction
are possible.

● Smooth and quiet operation with little vibration. Withstands operation at a

maximum speed of 60m/sec
● Excellent heat resistance, oil resistance and antistatic properties
● Almost no need for re-tension since the belt doesn’t stretch much

Dimensions & Product Code

Belt Length(mm)
Power Transmission Belt

Belt Type
2Frictional Forced

Belt Width(mm)

Standard Belt Sizes

Applications

47
 Frictional Forced Power
Transmission Belt

SUPER FLEXSTAR®® Belt

SUPER FLEXSTAR® is a high tension flat belt developed for
press application whereby a belt and a pulley sandwich and
dewater objects.

● High belt tension

● Besides press application, it also suits applications like conveyance.

Product Code (Example)

50 FW 3150
Belt Length (mm)
Belt Type
Belt Width (mm)
Cross-Sectional Diagram

Top cushion: Chloroprene rubber

a
Cord protection material : Nylon

Power Transmission Belt

Adhesion rubber : Chloroprene rubber

2Frictional Forced
b Cord : Aramid

Cord protection material : Nylon

Bottom cushion : Chloroprene rubber

Belt Types

a b
Standard Width Belt Thickness Standard Size Minimum Pulley Belt Edge Tensile Strength
(mm) (mm) (mm) Diameter(mm) Finishing (kN/cm)

48
 Frictional Forced Power
Transmission Belt

FLEXSTAR®® Belt J
FLEXSTAR® Belt J is a thin, flexible and seamless high-precision flat belt,
developed specially for conveyance of tickets, plastic cards, paper
money, coins and so on.

● Good running stability

● Reliable conveyance
● Excellent abrasion resistance and adaptability
● Maintenance-free

Product Code (Example)

10 - JLB - 500 - 1.0
Belt Width (mm) Belt Thickness (mm)
Belt Type Belt Length (mm)
Product Lineup

W T
Power Transmission Belt
2Frictional Forced

Polished

Polished

ex)

ex)

ex)

49
 Frictional Forced Power
Transmission Belt

POLYMAX®® Belt
This is a wide-angle belt with an angle of approx. 60° .

● High-speed power transmission with low vibration

● Compact design and cost efficient
● Maintenance-free and stretch resistance
● Excellent weather resistance

Cross-Sectional Sizes & Product Code

POLYMAX® Belt Multi-POLYMAX® Belt

Dimensions

Power Transmission Belt

2Frictional Forced
Dimensions

Product
Code Effective Length(mm) Product Effective Length(mm) Belt Type No.of Ribs
Code
Belt Type

Standard Belt Sizes

50
 Frictional Forced Power
Transmission Belt

MB Belt (Polyurethane V-Belt)

A small transparent belt for light-duty power transmission

● With its high flexibility, it can be used with a small diameter pulley.
● Excellent abrasion resistance and thus clean operation
● Small slippage operation
● Excellent oil resistance

Cross-Sectional Dimensions & Product Code

Top Width a (mm)

Belt Length (Outer Perimeter in mm)

Power Transmission Belt

Belt Type
2Frictional Forced

Dimensions

Standard Belt Sizes

Belt Length

Form & Dimensions of Pulley Grooves

30mm and above

Minimum Pulley Diameter

51
 Frictional Forced Power
Transmission Belt

STARROPE®®/ SUPER STARROPE®®/

PRENE V-ROPE / PRENE HEXAGONAL-ROPE
This is an open-end polyurethane belt.

● It is easily applicable in complex power transmission system such as

multiaxial and divertible power transmission.
● Thermal weld: Endless belt length possible.
● Excellent abrasion and oil resistance

PRENE V-ROPE PRENE HEXAGONAL ROPE

Power Transmission Belt

2Frictional Forced
STARROPE®/ SUPER STARROPE® Dimensions

Belt Code 2φ 3φ 4φ 5φ 6φ 7φ 8φ 9φ 10φ 12φ 15φ

d (mm)
Length of 1 Roll(m)

PRENE V-ROPE Cross-Sectional Dimensions

a (mm)
b (mm)
θ( °)

Lengh of 1 Roll (m)

PRENE HEXAGONAL-ROPE Cross-Sectional Dimensions

a (mm)
b (mm)
θ( °)

Lengh of 1 Roll (m)

Pulley for STARROPE®/ SUPER STARROPE® Pulley for PRENE V-ROPE / PRENE HEXAGONAL-ROPE

PRENE V-ROPE PRENE HEXAGONAL-ROPE

b (mm)
h (mm)

Pulley Dimensions for STARROPE®/ SUPER STARROPE®

Belt Code 2φ 3φ 4φ 5φ 6φ 7φ 8φ 9φ 10φ 12φ 15φ

a (mm)
w (mm)
h (mm)

52
 Frictional Forced Power
Transmission Belt

Flat Belt
This is a high-quality flat belt made from premium fabric and
synthetic rubber.
There is very little belt shrinkage.
Excellent flex resistance
Heat, water and oil resistance

● For textile and agricultural machines

Product Lineup

Side / core fabric : white

JIS 1st Class Round Edge Type Tape color : light green
Equivalent special PORT® Mark color : brown

Side / core fabric : yellow-brown

Round Edge Type Tape color : brown
Mark color : orange
PORT®
JIS 2nd Class
Power Transmission Belt

Equivalent
2Frictional Forced

Side / core fabric : yellow-brown

Cut Edge Type Edge adhesive : red
PIONEER® Mark color : brown

Flat Belt
Side / core fabric : red-brown
Round Edge Type Tape color : green
HARBOUR® Mark color : green

JIS 3rd Class

Equivalent
Side / core fabric : red-brown
Cut Edge Type Edge adhesive : green
ECHO® Mark color : green

DRY FLEX® Applicable for lifter with its stretch resistant.

For LA, LB, LC types, it is possible to add V rails.
For lifter
Others
Covered by canvas, this belt has a nonsticky surface. Single sided belt
Canvas surface is manufactured only in cut edge type whereas double sided belt can be
supplied in both cut and round edge type
specification

Standard Sizes for Round Edge Products

No. of Plies 2P 3P 4P 5P 6P 7P 8P
Belt Width
20mm
25mm H . P
30mm H . P
38mm H . P H
50mm H . P H .P
H . P H .P
63mm
75mm H . P H . P H .P
90mm H . P H H .P
100mm H . P H H .P P
125mm H . P H H H.P
150mm H H H P H.P
175mm H H P
200mm H H P P
250mm H H P P
300mm H H P
350mm H
400mm
500mm
600mm
● H: HARBOUR® P: PORT®
● Made-to-order for cut edge type (PIONEER®, ECHO®), DRY FLEX® and Canvas surface types.
● A lot for made-to-order items is 100m.

53
3 Direct Connected
Power Transmission
Chemi-Chan®
(High Performance Miniature Coupling) .........P55
HYPERFLEX® Coupling.....................................P56
TSCHAN® Coupling NOR-MEX® .................P57, 58
TSCHAN® Coupling S .................................P59, 60

54
 Direct Connected Power
Transmission

“Chemi-Chan®®”
(High Performance Miniture Coupling)
“Chemi-Chan®”, high-performance miniature coupling,
launched on the market for high precision rotary transmis-
sion.
● Excellent vibration absorption
● Quiet operation
● Accurate positioning and transmission of rotating power
● High durability which withstands harsh start and stop of power shaft.

Coupling Product Code (Example)

HAS - 22 - 8x6 - C(or F)
C: Clamp Type
Coupling Code
F: With Flange (opaque ring)
Duplex Shaft Diameter
Coupling Outer Diameter (φ22) (large diameter x small diameter)

Standard Sizes
Power Transmission
3Direct Connected

Peak maximum torque should be twice less than rated torque.

Currently, we use a screw method to mount it onto the shaft.
We use a mass of coupling with a drilled hole as a standard product mass.

Applications

55
 Direct Connected Power
Transmission

HYPERFLEX®® Coupling (MT . MH)

Two types are available –MT type and MH type
MT type is a compression stress type, which is compact design with
large transmission torque.
MH type is a model uses shearing stress of elastic rubber.
MT Type ● Applicable for all kinds of applications.
● Compact size with large transmission torque.
● Easy-to-install and maintenance-free
● The polyurethane elastic body, which features excellent oil and abrasion
resistance.
MH Type ● High flexibility and excellent shock absorption
● Applicable as a torque limiter

Coupling Product Code (Example)

MT - G - 85
Type
Elastic Body: Rubber Size

Standard Sizes for MT Type

Polyurethane(U)

Power Transmission
3Direct Connected
Standard Sizes for MH Type

Applications

56
 Direct Connected Power
Transmission

TSCHAN®® Coupling
NOR-MEX®®
It consists of a flange and a unique shape elastic body, which withstands
large transmission torque. 20 types available and 301 total combinations.

● Energy-saving since it transmits large torque with small body.

● Suitable for machineries with high-speed revolution
● Elastic body can be easily attached and removed without moving machinery.
● Compact design application, quiet operation and also maintenance-free.
● Wide variety of sizes and types.

Coupling Product Code (Example)

Nor - Mex G 148
Size
Model
G Type

Standard Sizes

Regular Max. Max. Regular Max. Max. Regular Max. Max.

Outer Total
Torque Torque Revolution Diameter Outer
Torque Torque Revolution Diameter Total Torque Torque Outer Total
Revolution Diameter
Code TN Mmax Length Code Length Code Length
Speed mm mm TN Mmax Speed mm mm TN Mmax Speed mm mm
N.m N.m rpm N.m N.m rpm N.m N.m rpm
Power Transmission
3Direct Connected

Regular Max. Max. Outer Total Regular Max. Max. Outer Total Regular Max. Max. Outer Total
Torque Torque Revolution Diameter Length Torque Torque Revolution Torque Torque Revolution
Code TN Mmax Speed Code TN Mmax Speed Diameter Length Code TN Mmax Speed Diameter Length
mm mm mm mm mm mm
N.m N.m rpm N.m N.m rpm N.m N.m rpm

57
 Direct Connected Power
Transmission

TSCHAN® Coupling NOR-MEX® Series

Applications

Power Transmission
3Direct Connected

58
 Direct Connected Power
Transmission

TSCHAN®® Coupling S

● Small size with large torque

● Light, compact and easy to install and remove
● Suitable for machinery with high revolution speed
● Quiet operation and longer operating life
● Maintenance-free

Coupling Product Code (Example)

S 200 St - U
Elastic Body: Polyurethane
Model Flange Material
Size
Standard Sizes for TSCHAN® Coupling S

Maximum Torque Outer Outer

Mmax(N.m) Outer Total Diameter Total Diameter Total Outer Total
Elastic Body Diameter Length Length Length Diameter Length
mm mm ST ZA mm VS ZA mm mm mm
Power Transmission
3Direct Connected

Applications

Combination Examples of Standard Types

S Type SX Type SV Type SZ Type

ST-TSN ST-TSN ZA-TSN ST-TSN ZA-TSN VS-TSN ZA-TSN ZA-TSN

✽ TSCHAN® is a registered trademark of TSCHAN® Corporation.

59
 Direct Connected Power
Transmission

TSCHAN® Coupling S

Power Transmission
3Direct Connected
Combination Examples

60
 4 Other Related
Products
SLEEVE ROLL (Polyurethane molded product) ..........P62
STARLOCK® (Shaft Fastener) .................................P63, 64

61
 Other Related Products

SLEEVE ROLL
(Polyurethane molded product)
It is a new press-in type roller coating and shock-absorption material,
which is formed by jointing soft and hard urethane in two layers.
● It is easily put onto iron cores or rollers by pressing. Also, it has a strong grip.
● It is very economical as it doesn’t require roll replacement caused by adhesive agents
as well as thermal lining onto iron cores or rollers.
● Excellent abrasion and oil resistance compared to plastic and rubber made rolls.
Also, it has excellent water and weather resistance.
● Two-layer structure of hard and soft urethane reduces shock and noise during back
conveyance. Moreover, a clean conveyance is possible as the roller rust does not
contaminate transporting items.

Applications Product Code (Example)

SR - 50 - 47
Protection of transported items, surface rust prevention, water Sleeve Roll Width Inner Diameter

washing operation line

Standard Sizes

Applicable Shaft Diameter(mm) Hardness( ) Stock Availability

Outer Layer+Inner Layer

4 Other Related
Products
(Outer)(Inner)

(Surface Cog Type)

How to put on

Jig

Sleeve Roll
Shaft Sleeve Roll PVC Pipe
Shaft

62
 Other Related Products

STARLOCK®®
STARLOCK® is a lock system that offers simple yet secure and strong
attachment of shaft and boss without troublesome key groove processing.
Thus, it also saves calculation and control processes required for shrink
and force fit methods.
With this system, shaft and boss are easily put together by high surface
pressure.
● Absolutely no need for shaft hole and key groove processing
● Non-backlash
● Any positioning on the shaft is possible
● Easy attachment and detachment

STL-20S STL-21S
STL - 20S - 20 - 47 STL - 21S - 19 - 47
Outer Diameter Outer ring
Outer Diameter
Inner Diameter Inner Diameter
(Shaft Diameter) (Shaft Diameter)
Model Number Model Number
Starlock Starlock

Performance & Sizes Performance & Sizes

Product Code Product Code

4 Other Related
Products

Standard Size Range : d = φ5∼φ100

Transmission torque and thrust shown above are maximum values.

Standard Size Range : d = φ20∼φ280

Transmission torque and thrust shown above are maximum values.
63
 Other Related Products

STARLOCK®

STL-21F STL-30R
STL - 21F - 19 - 47 STL - 30R - 20 - 25
Outer ring Outer Diameter Outer Diameter
Inner Diameter Inner Diameter
(Shaft Diameter) (Shaft Diameter)
Model Number
Model Number
Starlock
Starlock
Inner ring

30F
Performance & Sizes Performance & Sizes

Product Code Product Code

STL - 30F - 25 - 30
Outer Diameter
Inner Diameter
(Shaft Diameter)
Model Number
Starlock

Pressurized Flange

Product Code

4 Other Related
Products

Standard Size Range : d = φ5∼φ100

Transmission torque and thrust shown above are maximum values.

64
65
5Troubleshooting for Power
Transmission Products
For Timing Belt .................................................P67
For V-Belt ...........................................................P68

66
 Troubleshooting for Power
Transmission Products

Failure during machinery operation is a serious matter. To resolve belt failure, determine cause of failure
before replacing with a new belt. This will maximize the capability of the belt and extend its life.
The following is an introduction to belt failure main causes.
Please check the items in this table when failure occurs.

■ 1. For Timing Belt

Occurrence Cause Measure

● Poor alignment Adjust the alignment

Abnormal side wear ● Base not adequately fixed Strengthen the base fixture
● Bending of the pulley flange Correct flange bending
Abnormal wear at tooth surface ● Overload Amend the design and use better grade
where pressure is being exerted ● Overstretched belt Adjust the initial tension of the belt
● Overstretched belt Adjust the initial tension of the belt
Abnormal wear at contact point
● Defective pulley tooth form Replace using special attention on the R of
of pulley area
the pulley tooth end
● Pulley diameter too small Change the system design
●6 teeth or less for T.I.M Increase T.I.M or change the system design
Tooth damage
● Exertion of shock load Ensure that shock is not exerted on the belt or
increase the belt width
● Overload Change the system design
● Drop in elasticity or corrosion of Check the storage condition and transport
Breaking of tensile body tensile body condition of the belt
● Exertion of shock load Ensure that shock is not exerted on the belt or
increase the belt width
● Usage under -30℃ Raise the surrounding temperature
Crack at the back side
● Pulley diameter too small Use a bigger diameter pulley
Thermal ageing of rubber/ ● Temperature of 80℃ and above at the Reduce the surrounding temperature
polyurethane rubber/ polyurethane
Swelling of the rubber ● Oil contamination Use polyurethane or oil resistant rubber belt
● Overload Change the system design
● Overstretched belt Adjust the initial tension of the belt
Abnormal wear at pulley tooth
● Unsuitable pulley material (too soft) Add surface treatment or change the material
of pulley
● Pulley life Change to a new pulley
Wear at pulley edge ● Overstretched belt Change to new pulley and belt while
5 Troubleshooting

(Tensile body can be seen underneath the belt) loosening the tension
● Poor alignment Adjust the alignment
● Overstretched belt Adjust the initial tension of the belt
● Overload Change the system design
Abnormal operation sounds
● Pulley diameter too small Change the system design
● Defective pulley tooth form Ensure that pulley tooth is accordance to
standard dimensions
● Short inter-shaft distance Adjust to the correct inter-shaft distance
Belt looks elongated
● Loosening of the base Strengthen the base fixture

67
■ 2. For V-Belt
Occurrence Cause Measure

● Loose belt tension Apply appropriate tension

● Overload Increase belt width or increase the number of belt in use.
● Minimum contact angle Widen belt width or install an idler pulley of the
Slippage
appropriate diameter
● Oil or water contamination Completely remove the oil and water and
prevent further contamination by placing the belt cover
● Load variation/ large shock While there are design elements to be altered, the
● Use the belt above its transmission capacity specified type and number of belts should be installed
● Belts not mounted according to the specified (Depending on the application, please upgrade the belt
number of belts specification by 1 level)
Early failure ● Not using the specified belt type
● High heat generated and large flex fatigue Take counter-measure on heat dissipation or change
(overly small pulley diameter/ bending angle and the system design - alter the pulley diameter,
high revolution speed) revolution speed, bending angle
● Tension loss and slippage Apply appropriate tension
● Tension loss and slippage Apply appropriate tension
● Use under high temperature Take counter-measure on heat dissipation
● Continuous sudden stoppage and start-up Change the system design
Crack ● Oil contamination Fix oil leak and prevent oil contamination
● Pulley diameter too small Change the system design
● Too strong reverse bending due to backside tension
● Direct exposure to sunlight Install belt cover
● Tension pulley diameter too small Use a larger diameter tension pulley
Base crack ● Small bending angle Decrease the bending angle
● Loose tension and occurrence of slippage Apply appropriate tension
● Rusty pulley groove or rough finishing of pulley Perform uniform finishing on the pulley groove surface
groove surface (Standard 12S to 6S)
● Tension loss and slippage Apply appropriate tension
Wear ● Inappropriate pulley installation angle Change alignment to 1/3°and below or
● Defective pulley form replace the pulley
● Inappropriate pulley groove angle

5 Troubleshooting
● Damage on pulley groove
● Resonance due to unstable fixture of machine body Secure the fixtures
Excessive
● Weak belt tension Change inter-shaft distance
vibration
● Belt lengths not uniform Use matched set
● Belt used beyond its transmission capacity Mount belts with the right specification, type, number
Peeling ● Usage under deformed condition Change the system design
● Usage method resulted in large flex fatigue
● Sudden stop and start during usage Consider changing the system design for smooth
operation
● Belt tension too loose Apply appropriate tension
Noise problem
● Overload Increase belt width or increase the number of belt in use.
● Wrong belt type Select belt type, specification that matches the operating
conditions
● Inappropriate pulley groove angle, installation angle Change alignment to 1/3°and below
● Pulley groove damage or sticking of belt due to Replace the pulley
Overturning of belt roughly finished surface
● Wear at pulley groove
● Belt lengths not uniform during multiple usage Use matched set

68
 2. CONVEYOR BELTS
Product Lineup ........................................P70
NEOFLEXSTART® .............................P71∼76
FREESPAN® Belt ......................................P77

69
 Conveyor Belts & Related Products

NEOFLEXSTART® FREESPAN® Belt Conveyor Belt

Conveyor
Belts

Polyurethane Screen ROUND CONVEYOR PORTFLEX®

Related
Products

Applications & Properties

Product Lineup Rubber Conveyor • Abrasion resistance, heat resistance, oil resistance,
Belt suitable for inclined conveyance

• Suitable for food product conveyance, small diameter

Conveyor Plastic Belt pulleys
Application NEOFLEXSTART® • For logistic terminal, production line
• Heat resistant, non-adhesive
FREESPAN® Belt • Synchronous conveyance

ROUND
Conveyor • Circling, diverging conveyance
CONVEYOR
Products Conveyor System
Products
PORTFLEX® • Steep angle conveyance

Polyurethane • Oscillating separation screen

Screen
Peripheral
Products
GRIPTITE® • Plastic pulley lining material

Application Examples
Light-duty Plastic Conveyor Belt Synchronous Transportation Conveyor Belt
NEOFLEXSTART ®
FREESPAN® Belt
CONVEYOR BELTS

70
 Conveyor Belts

Characteristics & Use

The NEOFLEXSTART® will support automation and

manpower reduction at production and logistics sites.
This product will support a wide range of conveyor
systems.
Each Mitsuboshi “NEOFLEXSTART® U, V, F, P” has its own unique characteristics.
Thus, it is most important to select the correct belt to maximize the belt’s performance.

Safe, clean, stylish Color White, green, black

It works well in many fields, but it is best used for
conveyor lines that require cleanliness.
Using special polyurethane cover with excellent
mildew resistance and water resistance,
It is most suitable for conveying food products.
Also, it has excellent anti-static properties.

It fits in a wide-rang of applications. Color : White, green, dark blue

Also, after-processing such as adding crosspieces
is easy.
It works well in conveyance of oily items, plywood,
chemical products and various kinds of loads.
Excellent abrasion, ozone and chemical resistance,
as it is covered with high-quality PVC plastic.

It is usable under various conditions in which Color Brown, black, white, red
cold / heat resistance and/or non-adhesive
qualities are required.
Excellent heat resistance and non-adhesiveness
as it is coated with Teflon or silicone.
It works well in the places where belt conveyance
is difficult due to high temperature and character-
istics of transporting items such as adhesive
items and chemicals.
CONVEYOR BELTS

The best to be used in conveyance of sticky Color Transparent

items like bread dough
Polyolefin resin provides superior performance
when used in conveyance of sticky items like
bread dough.
Excellent for food conveyance.

71
 Oil and Chemical Resistance Table

NS-U NS-V NS-F NS-P

UG
Category Name of Chemicals UFG BK UPG VG SS
UR Type 0/0 UKG VN Type VKU VKG FG FK SG PN
UFR Type
UHG
Animal oil Ο Ο Ο Ο Ο Δ Δ Δ Ο Ο Ο Ο

Vegetable oil Ο Ο Ο Ο Ο Δ Δ Δ Ο Ο Ο Ο

Mineral oil Ο Ο Ο Ο Ο × × × Ο Ο Ο Ο
Oil &
DOS Δ Ο Δ Ο Δ × × × Ο Ο Ο Δ
Lipids Ο Ο Ο Δ
Grease Ο Ο Ο Δ Δ Δ Ο Ο

Paraffin oil Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο

Cutting oil × Ο × Ο Ο × × × Ο Ο × ×

Disinfectant Sodium Hypochlorite 400ppm Ο Δ Ο Ο Ο Δ Δ Δ Ο Ο Ο Ο

Methyl Alcohol (Methanol) Ο Ο Ο Ο Δ Δ Δ Δ Ο Ο Ο Ο

Ethyl Alcohol Ο Ο Ο Ο Δ Δ Δ Δ Ο Ο Δ Ο

Acetone × × × × × × × × Ο Ο × Δ
Solvent Gasoline × × × × × × × × Ο Ο × Δ

Toluene (Triol) × × × × × × × × Ο Ο × Δ

Methyl Ethyl Ketone (MEK) × × × × × × × × Ο Ο × ×

Formaldehyde (Formalin) 37% × × × × Ο Ο Δ Ο Ο Ο Ο Δ

Ammonia solution Ο Δ Ο Δ Ο Ο Δ Ο Ο Ο Ο Ο
Bases Sodium Hydroxide (Caustic Soda) 10% × × × × Δ Δ × Δ Ο Ο Ο Ο

Developing fluid (Hydroquinone) Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο

Nitric acid 5% × × × × Ο Ο × Ο Ο Ο Ο Ο

Hydrochloric acid 5% Ο × × × Ο Ο × Ο Ο Ο Ο Ο
Acids
Sulfuric acid 50% × × × × Δ Δ × Δ Ο Ο × Δ

Acetic acid 10% × × × × Δ Δ × Δ Ο Ο Ο Ο

Sodium Chloride (salt) Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο

Other
Soap Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο
chemicals Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο Ο
Fertilizer (general)
Ο=Applicable Δ= Possibility of damage ×=Not applicable

Electrostatic Potential
Running Electrostatic Potential ( Measured Values at Mitsuboshi)
∗For antistatic belts such as NS82UG0/2G, Running Electrostatic Potential (V)
NS-V, as they are processed for static (Absolute Value)
prevention inside, the surface resistance NS82UG0/2G* 1000 & below
values are the same as non-antistatic belts. NS-U All antistatic belts NS41UG0/2BK
50 & below
NS82UG0/2BK
Test conditions: NS-V All antistatic belts 200~1000
Belt speed 150m/min NS14FG-B
Antistatic belt 50 & below
Temperature 25±5°C NS-F NS15FK-B
Humidity 50±10% Non-antistatic belt 20000~30000
NS-P Antistatic belt 1000 & below

Adding Profiles (NEOFLEXSTART®-U,V)

The following are the examples of profiles which can be added to the belt.
CONVEYOR BELTS

Guides Low Profiles Cleats Lugs

(For preventing meandering) (For preventing loads from falling) (For slopes) (For steep angle conveyance)

Hole Punching

We provide hole punching on your requests.

72
 Conveyor Belts

Cover No. of
Total
Top Surface Underside Tension
Product Code Thickness
Thickness Thickness Member
Color Surface Condition Color Surface Condition mm
mm mm Ply
Heat & Humidity Resistance/ Prevention of Loose Threads
NS41UG0/2G Green 0.2 Flat Grey - Polyurethane impregnated conductive low noise fabric 1 0.8
NS41UG2/2G Green 0.2 Flat Green 0.2 Texture pattern (fine) 1 1.1
NS82UG0/2G Green 0.2 Flat White - Polyurethane impregnated conductive low noise fabric 2 1.4
NS82UG0/5G Green 0.5 Flat White - Polyurethane impregnated conductive low noise fabric 2 1.7
NS82UG2/2G Green 0.2 Flat Green 0.2 Texture pattern (fine) 2 1.7
NS123UG0/5G Green 0.5 Flat White - Polyurethane impregnated conductive low noise fabric 3 2.5
Antibacterial / Antifungal
NS41UFG0/2W White 0.2 Flat White - Polyurethane impregnated conductive low noise fabric 1 0.8
NS41UFG2/2W White 0.2 Flat White 0.2 Texture pattern (fine) 1 1.1
NS82UFG0/2W White 0.2 Flat White - Polyurethane impregnated conductive low noise fabric 2 1.4
NS82UFG0/5WS White 0.5 Texture pattern (coarse) White - Polyurethane impregnated conductive low noise fabric 2 2
NS82UFG0/5W White 0.5 Flat White - Polyurethane impregnated conductive low noise fabric 2 1.7
NS82UF2/2WP White 0.2 Flat White 0.2 Flat 2 1.7
NS123UFG0/5W White 0.5 Flat White - Polyurethane impregnated conductive low noise fabric 3 2.5
Super Antistatic
NS41UG0/2BK Black 0.2 Flat Grey - Polyurethane impregnated conductive low noise fabric 1 0.8
NS82UG0/2BK Black 0.2 Flat White - Polyurethane impregnated conductive low noise fabric 2 1.4
Slip, Accumulator (Storage)
NS41UG0/0 White - Polyurethane impregnated conductive fabric White - Polyurethane impregnated conductive low noise fabric 1 0.6
NS41UG0/0G Green - Polyurethane impregnated conductive fabric Green - Polyurethane impregnated conductive low noise fabric 1 0.6
NS82UG0/0 White - Polyurethane impregnated sideslip fabric White - Polyurethane impregnated conductive low noise fabric 2 1.3
NS82UG0/0G Green - Polyurethane impregnated sideslip fabric Grey - Polyurethane impregnated conductive low noise fabric 2 1.3
NS41UHG0/2W White 0.2 Flat White - Polyurethane impregnated conductive low noise fabric 1 0.8
NS41UHG0/2G Green 0.2 Flat Grey - Polyurethane impregnated conductive low noise fabric 1 0.8
NS82UHG0/2W White 0.2 Flat White - Polyurethane impregnated conductive low noise fabric 2 1.4
NS82UHG0/2G Green 0.2 Flat White - Polyurethane impregnated conductive low noise fabric 2 1.4
Sideslip
NS82UPG0/0 White - Polyurethane impregnated sideslip fabric White - Polyurethane impregnated conductive low noise fabric 2 1.3
NS82UPG0/0G Green - Polyurethane impregnated sideslip fabric Grey - Polyurethane impregnated conductive low noise fabric 2 1.3
Sloped Conveyance
NS41UKG0/5GT Green 0.5 Longitudinal groove Grey - Polyurethane impregnated conductive low noise fabric 1 1.4
NS82UKG0/8GT Green 0.8 Longitudinal groove Grey - Polyurethane impregnated conductive low noise fabric 2 2.3
Round Conveyor
NS41UFR0/5W White 0.5 Flat White - Polyurethane impregnated conductive fabric 1 1.0
NS41UR0/5G Green 0.5 Flat Grey - Polyurethane impregnated conductive fabric 1 1.0
NS82UFR0/2W White 0.2 Flat White - Polyurethane impregnated conductive fabric 2 1.5
NS82UR0/2G Green 0.2 Flat White - Polyurethane impregnated conductive fabric 2 1.5
(Note): All types of NEOFLEXSTART®-U can be used in metal detector machine (except BK)

Cover No. of
Total
Top Surface Underside Tension
Product Code Thickness
Thickness Thickness Member
Color Surface Condition Color Surface Condition mm
mm mm Ply
CONVEYOR BELTS

General Oil Resistance

NS41VG5/5G Green 0.5 Flat Green 0.5 Texture pattern (fine) 1 1.7
NS82VG5/5W White 0.5 Flat White 0.5 Texture pattern (fine) 2 2.7
NS82VG5/5G Green 0.5 Flat Green 0.5 Texture pattern (fine) 2 2.7
NS183VN0/20W White 2.0 Flat White - Polyurethane impregnated conductive fabric 3 5.1
NS183VN0/20G Green 2.0 Flat White - Polyurethane impregnated conductive fabric 3 5.1
Low Noise
NS82VG0/5G Green 0.5 Flat White - Polyurethane impregnated conductive low noise fabric 2 2.1
NS82VG0/5W White 0.5 Flat White - Polyurethane impregnated conductive low noise fabric 2 2.1
NS82VG0/20G Green 2.0 Flat White - Polyurethane impregnated conductive low noise fabric 2 3.6
Sloped Conveyance
NS82VKG5/5DB Dark Blue 0.5 Flat Dark Blue 0.5 Texture pattern (fine) 2 2.7
NS82VKUG5/8DBT Dark Blue 0.8 Longitudinal groove Dark Blue 0.5 Texture pattern (fine) 2 3.1
NS82VKG0/20GD Green 2.0 Deep groove White - Polyurethane impregnated conductive low noise fabric 2 5.3
NS122VN0/20GSS Green 2.0 Rough top Grey - Polyurethane impregnated low noise fabric 2 5.5

73
 Characteristics Surface Condition Color
G=Loose threads prevention, S=Texture pattern (coarse) W=White NEOFLEXSTART Abbreviation Surface Figure
side rigidity, low noise T=Longitudinal groove G=Green Permitted Tension (kN/mm) Color
F= Antibacterial, antifungal P=Two-sided, flat BK=Black
H=Slippery, nonadhesive No. of Tension Member Ply Top Cover Thickness (1/10mm)
P=Sideslip (palletizer) Material (Polyurethane) Underside Cover Thickness (1/10mm)
K=Sloped conveyance Characteristics
R=Trough, round conveyor

Weight Allowable Minimum Pulley Knife Edge Radius Usable Temperature Range
Table- Antistatic
Tension Diameter Product Code
Dry Heat Wet Heat Drive Specification
kg/m2 N/mm mm mm
Temperature ∗3°C Temperature°C
Heat & Humidity Resistance/ Prevention of Loose Threads
0.7 4 15 R3 -30~100 0~80 Ο Ο NS41UG0/2G
1.0 4 30 × -30~100 0~80 × Ο NS41UG2/2G
1.5 8 25 (15) ∗1 (R3) ∗2 -30~100 0~80 Ο Ο NS82UG0/2G
1.9 8 50 × -30~100 0~80 Ο Ο NS82UG0/5G
1.9 8 70 × -30~100 0~80 × Ο NS82UG2/2G
2.6 12 100 × -30~100 0~80 Ο Ο NS123UG0/5G
Antibacterial/ Antifungal
0.7 4 15 R3 -30~100 0~80 Ο Ο NS41UFG0/2W
1.0 4 30 × -30~100 0~80 × Ο NS41UFG2/2W
1.5 8 25 (15) ∗1 (R3) ∗2 -30~100 0~80 Ο Ο NS82UFG0/2W
1.9 8 25 (15) ∗1 × -30~100 0~80 Ο Ο NS82UFG0/5WS
1.9 8 50 × -30~100 0~80 Ο Ο NS82UFG0/5W
2.0 8 70 × -30~100 0~80 × Ο NS82UF2/2WP
2.6 12 100 × -30~100 0~80 Ο Ο NS123UFG0/5W
Super Antistatic
0.7 4 15 R3 -30~80 0~70 Ο Ο
Ο NS41UG0/2BK
1.5 8 25 (15) ∗1 (R3) ∗2 -30~80 0~70 Ο Ο
Ο NS82UG0/2BK
Slip, Accumulator (Storage)
0.4 4 20 R3 -30~100 0~80 Ο Ο NS41UG0/0
0.4 4 20 R3 -30~100 0~80 Ο Ο NS41UG0/0G
1.1 8 40 (30) ∗4 × -30~100 0~80 Ο Ο NS82UG0/0
1.1 8 40 (30) ∗4 × -30~100 0~80 Ο Ο NS82UG0/0G
0.7 4 15 R5 -30~100 0~80 Ο Ο NS41UHG0/2W
0.7 4 15 R5 -30~100 0~80 Ο Ο NS41UHG0/2G
1.5 8 25 (15) ∗1 (R3) ∗2 -30~100 0~80 Ο Ο NS82UHG0/2W
1.5 8 25 (15) ∗1 (R3) ∗2 -30~100 0~80 Ο Ο NS82UHG0/2G
Sideslip
1.1 8 30 × -30~100 0~80 Ο Ο NS82UPG0/0
1.1 8 30 × -30~100 0~80 Ο Ο NS82UPG0/0G
Sloped Conveyance
1.0 4 25 × -30~80 0~70 Ο Ο NS41UKG0/5GT
2.2 8 50 (25) ∗1 × -30~80 0~70 Ο Ο NS82UKG0/8GT
Round Conveyor
1.1 4 20 R5 -30~100 0~80 Ο Ο NS41UFR0/5W
1.1 4 20 R5 -30~100 0~80 Ο Ο NS41UR0/5G
1.6 8 30 × -30~100 0~80 Ο Ο NS82UFR0/2W
1.6 8 30 × -30~100 0~80 Ο Ο NS82UR0/2G
∗1,2: ( ) indicates values when permitted tension is 5N/mm and below. ∗3: For products indicated as Max 100°C, operating temperature is Max 80°C under continuous operation.
∗4: Lightning Endless type
Characteristics Surface Condition Color
G=Loose threads prevention, R=Texture pattern (fine) W=White NEOFLEXSTART Abbreviation Surface Figure
side rigidity, low noise D=Deep groove G=Green Permitted Tension (kN/mm) Color
K=Sloped conveyance SS=Rough top G2=Dark green
X= Low noise M=Diamond pattern GY=Grey No. of Tension Member Ply Top Cover Thickness (1/10mm)
DB=Dark blue Material (Polyvinylchloride) Underside Cover Thickness (1/10mm)
Characteristics

Weight Allowable Minimum Pulley Knife Edge Radius Usable Temperature Range
Table- Antistatic
Tension Diameter Product Code
Dry Heat Wet Heat Drive Specification
kg/m2 N/mm mm mm
Temperature °C Temperature°C
CONVEYOR BELTS

General Oil Resistance

1.9 4 35 × -10~80 0~60 × Ο NS41VG5/5G
2.8 8 70 × -10~80 0~60 × Ο NS82VG5/5W
2.8 8 70 × -10~80 0~60 × Ο NS82VG5/5G
5.8 18 120 × -10~80 0~60 Ο Ο NS183VN0/20W
5.8 18 120 × -10~80 0~60 Ο Ο NS183VN0/20G
Low Noise
2.3 8 50 × -10~80 0~60 Ο Ο NS82VG0/5G
2.3 8 50 × -10~80 0~60 Ο Ο NS82VG0/5W
4.1 8 100 × -10~80 0~60 Ο Ο NS82VG0/20G
Sloped Conveyance
2.8 8 75 × -10~70 0~60 × Ο NS82VKG5/5DB
3.4 8 75 × -10~70 0~60 × Ο NS82VKUG5/8DBT
4.2 8 80 × -10~70 0~60 Ο Ο NS82VKG0/20GD
6.5 12 80 × -10~70 0~60 Ο Ο NS122VN0/20GSS

74
 Conveyor Belts

Total Weight Allowable Surface

Product Code Thickness Tension Tension Member Cover Material Table-Drive
mm Kg/m2 N/mm Color Condition

NS03FG-P 0.075 0.3 2 Brown Flat Glass fiber Teflon Ο

NS05FG-P 0.125 0.3 2 Brown Flat Glass fiber Teflon Ο
NS06FG-P 0.150 0.3 2 Brown Flat Glass fiber Teflon Ο
NS10FG-P 0.250 0.5 3 Brown Flat Glass fiber Teflon Ο
NS14FG-P 0.350 0.7 6 Brown Flat Glass fiber Teflon Ο
NS27FG-P 0.680 1.1 9 Brown Flat Glass fiber Teflon Ο
NS22FG-S 0.550 0.7 8 Brown Flat Glass fiber Teflon Ο
NS05FG-B 0.125 0.2 2 Black Flat Glass fiber Teflon Ο
NS06FG-B 0.150 0.3 2 Black Flat Glass fiber Teflon Ο
NS10FG-B 0.250 0.5 3 Black Flat Glass fiber Teflon Ο
NS14FG-B 0.350 0.7 6 Black Flat Glass fiber Teflon Ο
NS27FG-B 0.680 1.1 9 Black Flat Glass fiber Teflon Ο
NS06FG-TR 0.150 0.3 2 Brown Flat Glass fiber Teflon Ο
NS10FG-TR 0.250 0.5 3 Brown Flat Glass fiber Teflon Ο
NS19FG-M 0.600 0.5 6 Brown Mesh Glass fiber Teflon Ο
NS21FG-M 0.750 0.4 4 Brown Mesh Glass fiber Teflon Ο
NS30FG-M 0.920 0.4 3 Brown Mesh Glass fiber Teflon Ο
NS15FK 0.350 0.4 6 Brown Flat Aramid fiber Teflon Ο
NS15FK-B 0.350 0.3 6 Black Flat Aramid fiber Teflon Ο
NS30FK-M 0.700 0.4 8 Brown Mesh Aramid fiber Teflon Ο
NS24SG-R 0.610 0.8 8 Red Flat Glass fiber Silicone ×
NS24SG-W 0.610 0.8 8 White Flat Glass fiber Silicone ×
NS42SG-R 1.060 1.5 12 Red Flat Glass fiber Silicone ×
NS42SG-W 1.060 1.5 12 White Flat Glass fiber Silicone ×

Cover
No. of Total
Top Surface Underside
Product Code Tension Thickness
Thickness Thickness Member Ply mm
Color Surface Condition Color Surface Condition
mm mm
NS32PN0/5NM White transparent 0.5 Diamond pattern White - Polyurethane impregnated conductive low noise fabric 2 1.9
NS11PN3/5NM White transparent 0.5 Diamond pattern White transparent 0.3 Flat 1 1.4
NS15PNM Transparent - Diamond pattern Transparent - Flat - 1.5
(Note) NS15PNM is polyolefin sheet and cannot be used as a belt.
CONVEYOR BELTS

75
 Characteristics Surface Condition Color
FG=∗Teflon/ glass fiber S=Standard Type (Standard specification) W=White NEOFLEXSTART Abbreviation Belt Type
FK=∗Teflon/ aramid fiber P=Premium Type (Flat and smooth specification) R=Red Material
SG= Silicone/ glass fiber M=Mesh Type (Standard specification) B=Black
(Cover material/ tension member material) TR=Tear Resistant Type Belt Thickness (shown value x 25.4/1000mm)
∗ is registered trademarks of Dupont

Usable Temperature Range Minimum Knife Edge Maximum

Pulley Radius Antistatic Manufacturable
Specification, Category Product code
Dry Heat Wet Heat Diameter Specification Width
Temperature °C Temperature °C mm mm mm
-150~270 0~80 70 × × 1000 Premium series NS03FG-P
-150~270 0~80 70 × × 1500 Premium series NS05FG-P
-150~270 0~80 70 × × 1500 Premium series NS06FG-P
-150~270 0~80 70 × × 2000 Premium series NS10FG-P
-150~270 0~80 70 × × 1500 Premium series NS14FG-P
-150~270 0~80 70 × × 2300 Premium series NS27FG-P
-150~270 0~80 70 × × 1500 Standard series NS22FG-S
-150~270 0~80 70 × Ο 1500 Antistatic type NS05FG-B
-150~270 0~80 70 × Ο 1500 Antistatic type NS06FG-B
-150~270 0~80 70 × Ο 2000 Antistatic type NS10FG-B
-150~270 0~80 70 × Ο 1500 Antistatic type NS14FG-B
-150~270 0~80 70 × Ο 2600 Antistatic type NS27FG-B
-150~270 0~80 70 × × 1000 Tear resistance NS06FG-TR
-150~270 0~80 70 × × 1000 Tear resistance NS10FG-TR
-150~270 0~80 100 × × 1500 1mm mesh NS19FG-M
-150~270 0~80 100 × × 1500 2mm mesh NS21FG-M
-150~270 0~80 100 × × 2500 4mm mesh NS30FG-M
-150~180 0~100 70∗ × Ο 2000 Kevlar core NS15FK
-150~180 0~100 70∗ × × 1500 Aramid fiber core Antistatic type NS15FK-B
-150~180 0~100 30 × × 2000 Aramid fiber core 4mm mesh NS30FK-M
-70~150 0~80 70 × × 950 Silicone series NS24SG-R
-70~150 0~80 70 × × 950 Silicone series NS24SG-W
-70~150 0~80 70 × × 950 Silicone series NS42SG-R
-70~150 0~80 70 × × 950 Silicone series NS42SG-W
∗ φ30 can be used when permitted tension is 1 N/mm and below (except inter-open endless type).

Characteristics Surface Condition Color

PN=Polyolefin M=Diamond pattern N=Transparent NEOFLEXSTART Abbreviation Surface Figure
Permitted Tension (N/mm) Color
No. of Tension Member Ply Top Cover Thickness (1/10mm)
Material (Polyolefin) Underside Cover Thickness (1/10mm)

Weight Allowable Minimum Pulley Knife Edge Operating Temperature Range

Table- Antistatic
Tension Diameter Radius Product Code
Dry Heat Wet Heat Drive Specification
kg/m2 N/mm mm mm
Temperature °C Temperature °C
1.7 3 40 × -10~60 0~60 Ο Ο NS32PN0/5NM
1.0 1 40 × -10~50 0~50 × × NS11PN3/5NM
1.0 - - - -10~50 0~50 - - NS15PNM CONVEYOR BELTS

76
 Possible to mold various shapes and profiles and
to add special cover on back surface of belt.

Lineup Metric Type

Inch Pitch Type
AT Type

STPD Type

Metric Type
Inch Pitch Type

STPD Type

Belt
Form

No. of Belt Teeth

Belt length in mm Fabric on tooth surface
only for flat belt F20/F20D L
Fabric on back surface
Belt Width Code A

Fabric on profile and tooth surface

Fabric on cover and tooth surface

Belt Form
Belt Cross-
Sectional
Dimensions
Belt Width Width Code Belt Width Width Code Belt Width Width Code Belt Width Width Code Belt Width Width Code Belt Width Width Code

Belt Width
(mm) &
Width Code
CONVEYOR BELTS

Belt Form
Belt Cross-
Sectional
Dimensions
Belt Width Width Code Belt Width Width Code Belt Width Width Code Belt Width Width Code Belt Width Width Code

Belt Width
(mm) &
Width Code

Maximum and minimum lengths of endless type are 100m and 700mm respectively. However, maximum length is 50m for the types with fabric on teeth side, back side and both sides.

F20, F20D and AT-20H are non-stock items.

77
3. ENGINEERING
PLASTIC PRODUCTS
Engineering Plastics
Size Table .............................................P79, 80

General Purpose Engineering Plastics

1. Casting Nylon ....................................................P81
2. UHMW-PE ....................................................P82, 83
3. Polyacetal...........................................................P84

High Performance Engineering Plastics

1. PEEK® ................................................................P85

Note 1. PEEK® is a registered trademark of Victrex®.

78
 ENGINEERING PLASTIC
PRODUCTS

Size Table
A: Rod Type Standard stocked item:● Non-stocked item: Δ
Outer Diameter
Name Grade Characteristics 4 5 6 8 10 12.5 15 17.5 20 22.5 25 30 35 40 45
Length
UD Improving mechanical strength signifi- 500L ● ● ● ●
cantly and reducing physical degradation 1,000L ● ● ● ●
(Ivory) under high temperature.
NB
500L ● ● ● ●
Blue colored grade which maintains
physical properties of cast nylon UD.
1,000L ● ● ● ●
Casting Nylon (Blue)
(CN)
CL
300L ● ● ● ●
Improving frictional property substantially
by our own lubricant formulation.
500L Δ Δ Δ Δ
(Green)
1,000L Δ Δ Δ Δ
MD
500L ● ● ● ●
Excellent lubricity property by evenly
blending molybdenum disulfide
1,000L Δ Δ Δ Δ
(Black)
● ● ● ● ● ● ● ●
Casting Nylon EX UD (Ivory) It has physical properties closer to casting ● ● ● ● ● ● ● ●
nylon while mechanical strength is enhanced ● ● ● ● ● ● ● ●
(CN-EX) NB (Blue) than standard nylon 6 extrusion products.
NA With small friction, it has excellent abrasion
and shock resistance as well as 1,000L ● ● ● ● ● ● ● ●
(White) antiadhesive properties. Also, nontoxic.
Ultra-High Molecular Better abrasion, thermal ageing and UV
ASB
Weight Polyethylene resistance than UHMW-NA. Also, it has 1,000L Δ Δ Δ Δ ● ● ● ●
(Black) high antistatic property.
(UHMW-PE)
ASG Light color, antistatic. Less surface
1,000L
(Mint green) abrasion against plastic bottles.

Homopolymer (DELRIN®) Excellent mechanical strength, fatigue

(White) resistance and dimension stability. 1,000L ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
(Black) 1,000L ● ● ● ● ● ● ● ● ● ● ● ●
Polyacetal Excellent mechanical strength, especially
Copolymer (DURACON®)
Engineering Polymers creep properties and fatigue resistance 1,000L ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
(White)
(POM) 1,000L ● ● ● ● ● ● ● ● ● ● ●
(Black) Excellent lubricity property addition to
Copolymer-BG mechanical strength and dimension 1,000L ● ● ● ● ● ● ● ●
(Green) stability of polyacetal.

PEEK® NA Excellent mechanical properties and chemical resistance.

All-purpose High performance engineering plastic with 1,000L ● ● ● ● ● ● ● ● ●
(Polyetheretherketone) (Light brown) maximum continuous operating temperature of 240°C.

B: Plate Type Standard stocked item:● Non-stocked item: Δ (Unit:mm)

Plate Thickness
Name Grade Characteristics 1 2 2 3 5 6 7 8 10 12 15 20 25 30 35 40 45 50 60 70 80 90 100 120
UD･ENB ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
1,000×2,000 CL ● ● ● ● ● ● ● ● Δ Δ Δ Δ Δ Δ Δ
MD Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ
UD･ENB ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
Casting Nylon 1,000×1,000 CL Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ
(CN) MD Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ
500×1,000 UD･ENB ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
UD･ENB ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
600×1,200 CL ● ● ● ● ● ● ● ● ● ● ● ● Δ Δ Δ Δ Δ Δ
MD ● ● ● ● ● ● ● ● ● ● ● ● Δ Δ Δ Δ Δ Δ
Ultra-High Molecular 940×1,920 NA ● ● ●
Weight Polyethylene ASB ● ●
1,000×2,000 NA ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
(UHMW-PE) ASB ● ● ● ● ● ● ● ● ● ● ● Δ Δ Δ Δ Δ Δ
600×1,200 Copolymer (White) ● ● ● ● ● ● ● ● ● ● ● ●
(Black) ● ● ● ● ● ● ● ● ● ●
Polyacetal Engineering 500×1,000 Homopolymer (DELRIN®) (White) ● ● ● ● ● ● ● ● ● ●
Copolymer (DURACON®) ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
Polymers (POM)
(White)(Black) ● ● ● ● ● ● ● ● ● ● ●
Copolymer-BG (Green) ● ● ● ● ● ● ● ●
M5BK (Black) ● ● ● ● ● ● ●
PEEK® 500×1,000 NA Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ
(Light brown)
(Polyetheretherketone)
ENGINEERING PLASTIC
PRODUCTS

79
 (Unit:mm)

50 55 60 65 70 75 80 85 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250 260 270 280 290 300 310 320 330 340 350 380 400 450 500 550 600
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● Δ Δ Δ Δ
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●

● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● Δ Δ Δ Δ
● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
● Δ Δ Δ Δ Δ
● ● ● ● ● ● ● ● ● ●
Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ
Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ
● ● ● ● ● ● ● ● ● ● Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ
Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ

● Δ Δ Δ Δ Δ
● Δ Δ Δ Δ Δ

● ● ● ● ● ● ● ● ● ● ● ● ● ●

● ● ● ● ● Δ Δ Δ Δ Δ Δ Δ Δ Δ

Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ

● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
● ● ● ● ● ● ● ● ● ● Δ Δ Δ Δ Δ Δ Δ Δ

● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ●
● ● ● ● ● ● ● ● ● ● ● ● ● ● ●

● ● ● ● ● ● ● ● ● ●

● ● ● Δ Δ Δ Δ Δ

C: Pipe Type Non-stocked item: Δ (Unit:mm)

60 65 70 70 75 80 80 90 90 100 100 110 120 130 140 150 150 165 180 200 200 225 225 250 250 285 300 300 330 350 400 430
Name Length Grade Outer Diameter
Inner Diameter 25 40 25 45 50 30 55 40 65 50 75 60 70 80 90 100 125 115 100 100 150 115 175 125 200 225 150 250 165 175 350 250
Casting 1,200 UD･NB Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ
MD Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ
Nylon
UD･NB Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ
(CN) 350 CL Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ
MD Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ Δ

Note
1. DELRIN® is a registered trademark of DuPont®.
2. PEEK® is a registered trademark of Victrex®.
3. DURACON® is a registered trademark of Polyplastics K.K.
ENGINEERING PLASTIC
PRODUCTS

80
 ENGINEERING PLASTIC
PRODUCTS

1. Casting Nylon
1-1. MEP® Casting Nylon Grades

■ CN-UD Ivory Load Bearing ■ CN-NB Blue Load Bearing

By improving mechanical strength, a characteristic of casting nylon, and reducing physical degradation
under high temperature, it can be used under heavy loads like machinery parts for where only metal is
used. CN-NB is a blue colored grade of CN-UD and has the same properties as CN-UD.

■ CN-MD Black Light Load Sliding ■ CN-CL Green (Non-lubricated) Sliding

It has enhanced sliding property base on excellent By our own patented production method, it has outstandingly high
properties of casting nylon by evenly blending abrasion resistance while maintaining the excellent properties of
molybdenum disulfide. casting nylon. Also, it has lubrication performance which withstands
prolonged operating time.

1-2. MEP® Casting Nylon EX Grades

■ CN-UDE Ivory Light to medium withstand load ■ CN-NBE Blue Light to medium withstand load

It has physical properties closer to casting nylon while mechanical strength is enhanced than standard nylon 6 extrusion products.
It is economical and best to be used as machinery parts such as small sized gears, roller bearings, rollers, etc.
CN-NBE is blue colored grade of CN-UDE with the same properties as CN-UDE.

1-3. Applications
① Metal and steel facility ② Transport equipment
③ Construction machinery ④ Machine tools
⑤ Industrial machinery ⑥ Shipbuilding, heavy industrial machinery
⑦ LCD, semiconductor manufacturing equipment

1-4. Properties of Casting Nylon

Table 1. Properties of Casting Nylon

CN-UD CN-UDE
Property ASTM Test Unit CN-MD CN-CL
CN-NB CN-NBE
Density D792 1.15~1.16 1.16~1.17 1.12~1.13 1.15
Tensile Strength D638 MPa 78 ~93 74~83 59~74 76
Tensile Elongation D638 % 20~50 15~40 10~40 48
Secant Modulus D638 103MPa 3.0~3.5 2.8~3.3 2.0~2.5 2.9
Compressive Strength D695 MPa 93~108 88~98 74~83 91
Flexural Strength D790 MPa 103~123 98~118 78~93 110
Izot Impact Strength D256 J/m 34~54 30~50 37~65 33
(1/2in x 1/2in notched)
Rockwell Hardness D785 R scale 115~120 113~117 107~112 120
Thermal Conductivity C177 W/(m･K) 0.20 0.20 0.20 0.20
Specific Heat Capacity - J/(KG･K) 1,046 1,046 1,046 1,250
Coefficient of Thermal Expansion D696 10-5 ℃ 8.0 9.0 8.6 9.0
Continuous Use Temperature - ℃ 140~170 120~150 100~120 100~120
Heat Distortion D648 ℃ 185~200 170~195 105~115 94
210~215 205~210 170~180 193
Volume Resistance D257 Ω• cm 1014 1014 1014 1014
Dielectric Strength D149 KV/mm 18~22 18~22 18~22 25.0
(Short interval 3.2mm)
Relative Permittivity D150 3.7 3.7 3.7 4.0
3.7 3.7 3.7 3.7
3.7 3.7 3.7 3.4
ENGINEERING PLASTIC

Loss Tangent D150 0.02 0.02 0.02 0.01

0.02 0.02 0.02 0.04
PRODUCTS

0.02 0.02 0.02 0.04

Water Absorption D570 % 0.5~0.9 0.9~1.2 0.6~0.8 1.3
(24 hours 3.2mm)
Allowable PV Index - kPa･m/sec 820 980 2,290 820

81
2. UHMW-PE (Ultra-High Molecular Weight Polyethylene)

2-1. MEP® UHMW-PE Grades

■ UHMW-NA White Standard Grade

UHMW-NA is a standard grade of Ultra-High Molecular Weight Polyethylene whose molecular

weight is from 3.5 to 6.5 million. It has excellent abrasion resistance, low friction coefficient,
antiadhesive property, chemical resistance, cold resistance and food safety.

■ UHMW-ASB Black High Antistatic Grade

UHMW-ASB is a grade with high antistatic performance. Its surface resistance is at a very low level of 104,
thus making it suitable to use as a static protection in LCD and semiconductor manufacturing equipment.
Also it has excellent abrasion and weather resistance.

■ UHMW-ASG Light Green Antistatic Grade

UHMW-ASB is an upgrade of UHMW-ASG, which antistatic property is added. Its surface

resistance is 1011. It has high abrasion resistance and suitable for food production and bot-
tling lines. Particularly, it has a low friction coefficient and good anti-abrasion, and does not
scratch PET plastic containers.

2-2. Applications
① Food production facility ② Transport equipment
③ Cement facility ④ Coal storage facility
⑤ Fodder storage facility ⑥ LCD, semiconductor manufacturing equipment
⑦ Chemical facility

2-3. Properties of UHMW-PE

Table 2. Properties of UHMW-PE

Property ASTM Test Unit UHMW-NA UHMW-ASB UHMW-ASG

Density D792 0.94 0.96 0.98

Tensile Strength D638 MPa 37 28 28
Tensile Elongation D638 % 365 250 215
Secant Modulus D638 103MPa 0.5 0.6 0.4
Compressive Strength D695 MPa 19 19 15
Flexural Strength D790 MPa 26 25 15
Izot Impact Strength D256 J/m No damage No damage No damage
(1/2in x 1/2in notched)
Rockwell Hardness D785 R scale 52 55 53
Thermal Conductivity C177 W/(m･K) 0.38 0.44 0.38
Specific Heat Capacity - J/(KG･K) 2,300 2,200 2,300
Coefficient of Thermal Expansion D696 10-5 ℃ 20 19 19
Continuous Use Temperature - ℃ 80 80 80
Heat Distortion D648 ℃ - - -
96 98 78
Volume Resistance D257 Ω･cm >1013 104 1011
Dielectric Strength D149 KV/mm - - -
(Short interval 3.2mm)
Relative Permittivity D150 2.3 2.3 2.3
- - -
- - -
ENGINEERING PLASTIC

Loss Tangent D150 1~2×10-4 1~2×10-4 1~2×10-4

1~2×10-4 1~2×10-4 1~2×10-4
PRODUCTS

1~2×10-4 1~2×10-4 1~2×10-4

Water Absorption D570 % <0.01 <0.01 <0.01
(24 hours 3.2mm)
Allowable PV Index - kPa･m/sec 490 490 490

82
 ENGINEERING PLASTIC
PRODUCTS

2-4. UHMW Rail Dimensions

UHMW Rail

Flat Rail Wear Tape

Rail Thickness Width (mm) Roll Length (m) NO Width (mm) Roll Length (m)
(mm)
3 15 50 1/4 6.35 15.5
3 20 50 1/2 12.7 15.5
3 25 50 3/4 19.05 15.5
3 30 50 1 25.4 15.5
3 40 50 1 1/4 31.75 15.5
3 50 50 2 50.8 15.5
4 25 40 3 76.2 15.5
4 30 40 4 101.6 15.5 L-Type

4 40 40 6 152.4 15.5
4 50 40 12 304.8 15.5
5 20 30 18 457.2 15.5 H-Type

5 25 30 Wear Tape
5 30 30 0.25mm thickness UHMW-NA tape with adhesive
5 40 30 exfoliating paper on one side can be used on the
places where rails cannot be mounted.
5 50 30
6 20 25 V3-Type V6-Type
6 30 25
6 40 25
6 50 25

C-Type C-Type
Chain Rail End Plate for Chain Rail for φ12 for φ10

Thickness (mm) Width (mm) Length (m) Thickness (mm) Width (mm) Length (m)
5 20 500 5 20 65
5 25 500 5 25 65
5 40 500 5 40 65
Snap-on Type
6 20 500 6 20 65
6 25 500 6 25 65

L-Type Rail H-Type Rail Color: White A-Type AⅡ-Type

Type Type Type
L-type White 5×20×1,000
(Note) Standard length is 50m/ a roll 5×25×1,000
(Note) (1) Attachment bracket ST5S is
JPY 500/piece.
(2) Standard length is 1000mm.
V-Type Rail Color: White R-Type for φ10 R-Type for φ12

Type Type
V3 -type 0
V6 -type 0
(Note) Standard lengths for V3 and for
V6 are 100m and 50m/ roll
respectively.

Snap-On Rail Color: White C-Type Rail Color: White

Type Length Type Length
SNP-type 30m For φ10 3m
For φ12 3m
ENGINEERING PLASTIC
PRODUCTS

R-Type Rail Color: White A-Type Rail Color: White

Type Length Type Length

For φ10 3m A -type Rail 3m

For φ12 3m AII-type Rail 3m

83
3. Polyacetal
3-1 MEP® Polyacetal Grades

■ Polyacetal Homopolymer White, Black (DELRIN®)

Engineering plastics with well balanced properties of mechanical strength, electrical properties and dimen-
sion stability Also, it has good fatigue resistance and superior machining properties. Mass production of
parts possible by injection molding.

■ Polyacetal Copolymer White, Black (DURACON®)

Engineering plastic with well balanced properties of mechanical strength, electrical properties and
dimension stability Also, it has good cleavage resistance and superior machining properties.
Mass production of parts possible by injection molding

■ Copolymer-BG Green High Sliding Performance Grade for light/medium load

A grade of polyacetal copolymer with special lubricant Excellent sliding performance for light to medium load with
mechanical strength, electrical properties and dimension stability Not only use in industrial machinery, it is also used
as a sliding component in LCD manufacturing system since it has well recognized wear resistant property.

■ M5BK Black High Sliding Performance Grade for medium/heavy load

A grade of Polyacetal copolymer with special lubricant Excellent sliding property with mechanical strength,
electrical properties and dimension stability Not only use in industrial machinery, it is also used as a sliding
component in construction machineries since it has well recognized wear resistant property.
Note 1. DELRIN® is a registered trademark of Dupont.
2. DURACON® is a registered trademark of Polyplastics K.K.
3. BESTAL® is a registered trademark of Bayer AG.

3-2 Applications
① Food production facility ② Transport equipment
③ LCD, semiconductor manufacturing equipment ④ Construction machineries
⑤ Packing machines ⑥ Electronic components manufacturing equipment

3-3 Properties of Polyacetal

Table 3. Properties of Polyacetal

Property ASTM Test Unit Homopolymer Copolymer Copolymer-BG M5BK

Density D792 1.42 1.41 1.38 1.38

Tensile Strength D638 MPa 69 61 54 57
Tensile Elongation D638 % 12 12 50 14
Secant Modulus D638 103MPa 2.8 2.8 2.0 2.0
Compressive Strength D695 MPa 124 108 74 66
Flexural Strength D790 MPa 97 89 72 75
Izot Impact Strength D256 J/m 69 69 59 40
(1/2in x 1/2in notched)
Rockwell Hardness D785 R scale 120 115 114 114
Thermal Conductivity C177 W/(m･K) 0.17 0.17 0.17 0.17
Specific Heat Capacity - J/(KG･K) 1,460 1,460 - -
Coefficient of Thermal Expansion D696 10-5 ℃ 9 10 10 10
Continuous Use Temperature - ℃ 90 90 90 90
Heat Distortion D648 ℃ 124 110 105 110
170 158 - -
Volume Resistance D257 Ω･cm 6×1014 6×1014 1014 -
Dielectric Strength D149 KV/mm 15 20 18 -
(Short interval 3.2mm)
Relative Permittivity D150 3.7 3.7 - -
3.7 3.7 - -
ENGINEERING PLASTIC

3.7 3.1 - -
Loss Tangent D150 0.003 0.001 - -
PRODUCTS

0.002 0.002 - -
0.005 0.007 - -
Water Absorption D570 % 0.25 0.22 0.22 0.22
(24 hours 3.2mm)
Allowable PV Index - kPa･m/sec 490 490 1,300 1,600

84
 ENGINEERING PLASTIC
PRODUCTS

4. High Performance Engineering Plastics

4-1 MEP® High Performance Engineering Plastics Grades

■ PEEK®-NA Light Brown Heat & Chemical Resistant Grade

A high performance engineering plastic with comparable to Teflon for its heat and chemical resistance.
It also has mechanical strength, electrical properties and machinability to casting nylon. Injection molding possible.
Used in many applications such as LCD / semiconductor manufacturing equipment, chemical equipment, plating equipment and logistic facility.
Note 1. PEEK® is a registered trademark of Victrex®.

4-2 Applications
① LCD, semiconductor manufacturing equipment ② Chemical production equipment
③ Plating industry ④ Aerospace industry
⑤ Medical equipment ⑥ Electronic component manufacturing equipment

4-3 Properties of PEEK®-NA

Table 4. Properties of High Performance Engineering Plastics

Property ASTM Test Unit PEEK®-NA

Density D792 1.30

Tensile Strength D638 MPa 97
Tensile Elongation D638 % 80
Secant Modulus D638 103MPa 2.8
Compressive Strength D695 MPa 127
Flexural Strength D790 MPa 142
Izot Impact Strength D256 J/m 59
(1/2in x 1/2in notched)
Rockwell Hardness D785 scale M98
Thermal Conductivity C177 W/(m･K) 0.2
Specific Heat Capacity - J/(KG･K) 1,330
Coefficient of Thermal Expansion D696 10-5 ℃ 4.8
Continuous Use Temperature - ℃ 240
Heat Distortion D648 ℃ 152
-
Volume Resistance D257 Ω･cm 1013~1014
Dielectric Strength D149 KV/mm 19
(Short interval 3.2mm)
Relative Permittivity D150 3.2~3.3
-
-
Loss Tangent D150 0.0016
-
-
Water Absorption D570 % 0.14
(24 hours 3.2mm)
Allowable PV Index - kPa･m/sec -
ENGINEERING PLASTIC
PRODUCTS

PEEK®-NA

85
M E M O

86
 M E M O

87
■ Global Factories & Sales Offices

■JAPAN ●MBL SHANGHAI INTERNATIONAL TRADING CO., LTD.

Rm.202, Block 3, Shanghai Withub White-cat, Science Park,
No. 641 Tianshan Road, Shanghai 200336,
●MITSUBOSHI BELTING LTD. CHINA
(Kobe Head Office) Tel:+86(21) 5206-7008 Fax:+86(21) 5206-7011
4-1-21 Hamazoe-dori,Nagata-ku,
Kobe 653-0024
●TIANJIN MITSUBOSHI BELTING CO., LTD.
Tel: +81-78-671-5071 Fax: +81-78-685-5670
1F, No.10, 3rd Rd. (#6 Standard Building)
Woqing Development Area, Tianjin, 301700
(Tokyo Head Office)
CHINA
Nihonbashi Plaza Bldg.10F
Tel:+86- 22-8211-0542 Fax:+86- 22-8211-0543
2-3-4 Nihonbashi, Chuo-ku,
Tokyo 103-0027
Tel: +81-3-5202-2500 Fax: +81-3-5202-2520 ●MOI TECH HONG KONG LTD.
Ever Gain Plaza 2nd Building 22F Rm.11
88 Container Port Road, Kwai Chung,
HONG KONG
■ASIA Tel:+852- 2403-5978 Fax:+852- 2422-8308

●MITSUBOSHI OVERSEAS HEADQUARTERS PTE. LTD.

14 Jurong Port Road,
SINGAPORE 619091
■AMERICA
Tel:+65-6265-3933 Fax:+65-6265-0954
●MBL(USA)CORPORATION
601 Dayton Road,
●MITSUBOSHI BELTING(THAILAND)CO.,LTD.
Ottawa Illinois 61350-9535
101/62/12 Moo 20, Navanakorn, Phaholyothin Road,
U.S.A.
Klong Nueng, Klong Luang, Patumtanee 12120,
Tel:+1-815-434-1282 Fax:+1-815-434-2897
THAILAND
Tel:+66-2-529-0691 Fax:+66-2-529-0695
●MITSUBOSHI CHEM. CORPORATION
1040 North. Ridge Avenue,
●STARS TECHNOLOGIES INDUSTRIAL LIMITED
Lombard, Illinois 60148-1281
Eastern Seaboard Industrial Estate
U.S.A
64/40 Moo 4, Tambon Pluakdaeng Amphur Pluakdaeng, Rayong 21140
Tel:+1-630-627-9650 Fax:+1-630-627-9655
THAILAND
Tel:+66-3895-4738 Fax:+66-3895-4740

●P.T. SEIWA INDONESIA ■EUROPE

Blok M-2-2, Kawasan Berikat, MM2100
Industrial Town, Cibitung, Bekasi, Jawa Barat 17520 ●MBL(EUROPE)B.V.
INDONESIA Energieweg 3,
Tel:+62-21-898-0324 Fax:+62-21-898-0325 2382 NA Zoeterwoude,
HOLLAND
●P.T. MITSUBOSHI BELTING INDONESIA Tel:+31-71-5899264 Fax:+31-71-5895062
Km. 8 Raya Serang,
JN. Industri Raya Block D No.4, ●MBL ANTRIEBSTECHNIK DEUTSCHLAND GmbH
Desa Pasir Jaya, Jatiuwung Tangerang, Bussardweg 10, D-41468 Neuss,
INDONESIA GERMANY
Tel:+62-21-5902070 Fax:+62-21-5902071 Tel:+49-2131-740940 Fax:+49-2131-7409424

●MITSUBOSHI BELTING PHILIPPINES CORPORATION ●MOI TECH EUROPE Sp.z o.o.

Mulawinan Road, Lawang Bato Valenzuela, Metro Manila Budynek B8 ul, 3-go Maja8,
PHILIPPINES 05-800 Pruszkow,
Tel:+63-2-445-4105 Fax:+63-2-445-4109 POLAND
Tel:+48-22-7383930 Fax:+48-22-7383939
●SUZHOU MITSUBOSHI BELTING CO., LTD.
277 Liangang Road,
Suzhou New District, Jiangsu 215129,
CHINA
Tel:+86-512-6665-8880 Fax:+86-512-6665-8886
(As of January 2007)

88
 MITSUBOSHI BELTING LTD.

The information contained herein is for information purposes only, and does not
enlarge, amend or imply any warranty other than provided by the manufacture with
the product. Any use of the product not in conformance with the manufacture's
instruction must be dangerous.

V6010500701Sg①474698
Printed in Singapore