EEL 5245 POWER ELECTRONICS I


Lecture #2: Chapter 1

Introduction to Power Electronics

 Discussion Topics
!
• Definition of Power Electronics
• Industry Overview/Market Share Analysis
• Multidisciplinary Nature of Power Electronics
• The Need for Power Electronics
• Types of Power Conversion
• Figures of Merit for Power Electronics Converters
• Applications for Power Electronic Converters
• Future Trends
 

What is Power Electronics?


• Electronics: Solid State Electronics Devices and their

Driving Circuits.
• Power: Static and Dynamic Requirements for Generation,
Conversion and Transmission of Power.
• Control: The Steady State and Dynamic Stability of the
Closed Loop system.

POWER ELECTRONICS may be defined as

the application of Solid State Electronics for
the Control and conversion of Power.
 The Worldwide Electronics

Market Overview

Power
Electronics
is an Enabling
Technology
Equipment Sales: $30B

Hardware Electronics
$570B

Total Electronics Market $1,000B

Source: Microtech
 National Critical Technology Areas
Technology Category Technology Area

Energy Efficiency
Energy
Energy Storage
Power Conditioning
Environmental
Quality Power Distribution

Information and
Communication Distributed Power Supplies
Living Systems
Manufacturing Process Control Automation

Materials
Avionics and Controls
Transportation Power System Integration
Propulsion for Mass Transit
Hybrid Electric Vehicles

Source: President’s Committee of Advisors on Science and Technology

 Historical Perspective
!
• Traditional power conversion
– Linear Electronics- Transistors in active mode (linear
region)
• Transistor acts as variable resistor for control
• Terrible efficiency (50% not uncommon)
• Low conversion range (greater Vd smaller efficiency)
• Low power applications
– Motor-Generator Sets (AC-DC or AC-AC)
• Can still be found in use
• Large physical size
• Maintenance intensive
• Low efficiency
• Poor Load regulation
 Modern Power Electronics
!
• Can have efficiencies approaching 100%
– Uses switches in saturation mode (On of Off)
– On state-resistance can be down in tenths of Ohms
• Are much smaller than predecessors
– High switching frequency means smaller magnetic
components.
– Reduced losses means smaller package size
• Net effect is better efficiency, greater power density (5W/
in^3 attainable)
 Simplified Block Diagram of 

a Power Electronics System

y1
x1 Load1

x2 y2
Power Electronic Load2
"Power" Circuit
yn
xm Loadn

Electrical f1 f2 fk Electrical or
Inputs Mechanical
"Sources"
Output "Loads"
Feedback
"Control Circuit"
 Detailed Block Diagram of 

Power Electronics System
Form of elec. or
Power proc. stage Post stage mechan. energy
Pre-stage
Output
Input Filter Filter
Electrical
& PE Circuit & Load
Mechanical
Form of Rectify Rectify
electrical
energy Could generate
undesirable
Mostly waveforms
unregulate
d dc Electrical Variable
voltage Feedback
Control
Switch
Drives

Circuit
Mechanical Variable
Mostly ac line Feedback
voltage (single
or three phase)
Interface between Process feedback
control and power signals and decide
circuits on control
 Multidisciplinary Nature 

of Power Electronics
• Power electronics is comprised of:
– Semiconductor Devices
– Analog Circuits
– Control Design
– Magnetics
– Electric Machines
– Power Systems Engineering
– Circuit Simulation
Power Electronics 

Focus Areas
 Growth In Power Electronics
!
• The technology boom of the semiconductor market creates power
devices with significant power handling and switch speed
capability (ICs for control as well)
• The expanding market demand for new power electronic
applications that require the use variable-speed motor drives,
regulated power supplies, robotics, uninterruptible power
supplies.
• The ever increasing demand for smaller size and lighter weight
power electronic systems.
• A result of this increasing reliance on power electronic systems
made it mandatory that all such systems have radiated and
conducted electromagnetic interference (EMI) be limited within
regulated ranges.
 The Drivers for Power Electronics
!
• Primary Factors Locally (KSC/Florida)
– Microprocessor-based technology has been producing devices
that often require tight regulation and uninterruptible power
– Increased sensitivity to power system harmonics
– Energy Conservation and Environmental Management are
now grouped within US Domestic Policy and are receiving
significant focus from Bush Administration
• New Legislation from Bush on Energy Conservation
Requirements
• New Florida Building Code will Require Variable Speed Air
Handlers
– Industrial Process Control and Automation is BOOMING with
new/refined motor drive applications
• HVAC (VAV, Chilled Water Flow, Chiller)
• Elevator Drives (DC Drives)
 Power Flow 

Unidirectional: input-to-output

(input) (output)
Source Side Load Side

II I
Power
Processing
Load
circuit
III IV
(P loss )
 Power Flow – Bi-directional

(input) (output)
Source Side Load Side

II I
Power
Processing
Load
circuit
(Ploss) III IV
 

Power Conversion Dictates 

Change in Current and/or Voltage:


• Voltage/Current form ac or dc
• Voltage/Current level (magnitude)
• Voltage frequency (line or otherwise)
• Voltage/Current waveshape (sinusoidal or
nonsinusoidal such as square, triangle,
sawtooth, etc.)
• Voltage phase(single or three-phase).
 Conversion Type Description

• Power Electronic systems perform one or more of the

following conversion functions:
!
a)Rectification (ac-to-dc)
b) Inversion (dc-to-ac)
c) Cycloconversion
(ac-to-ac different frequencies) or
(ac-to-ac same frequency)
d) Conversion (dc-to-dc)
Types Of Power Conversion
 Figures of Merit

for Power Electronic Converters
• What is the objective?
– Overall goal: To produce a converter that performs
well in these areas:
• Efficiency
• Transient Response
• Load and Line Regulation
• Power Density
• Input/Output Distortion (Input Power Factor)
• Reliability (MTBF)
• Cost
– In the final analysis, the job is to process and control
the flow of electric energy by supplying currents/
voltages in a form most suited to both the load and
energy source
 Industrial Applications
!
• SMPS
– PFC
– Universal Input
– Soft-Switching
• Uninterruptible Power Supplies
– Hot-Sync Paralleling
• Process Control
– Motor Drives (DC Drives-VSDs, VFD)
Motor Drive
Typical PC Power Supply
Classic Inverter Scheme
 Typical Commercial 

Power Supply-Univ. PFC 600W
 Typical Commercial 

Power Supply-Universal PFC 150W
 Future Trends
!
• Continue in the technological improvement of high power and
high frequency semiconductor devices.
• Attempts to improve energy density with increased efficiency
and performance
• Improvement in the design of driver circuits for switching
devices (DSP)
• Improvement in control techniques including optimal and
adaptive control.
• Integration of power and control circuitry on a single IC
• Distributed Power Systems (DPS).
• Power factor correction techniques and EMI reduction.
• New Power Transmission Concepts
 UCF Power Electronics 

FloridaPEC
Florida Power Electronics Center
Director: Dr. Batarseh
http://apec.engr.ucf.edu
!
• Power Factor Correction (PFC) circuits
• Soft-Switching DC-DC Converters
• Low Voltage AC-DC and DC-DC converters
• Low Voltage high-current fast-transient VRMs
• Dynamic Modeling and Control
• Electromagnetic Interference and Compatibility (EMI/
EMC)
• Modeling of Power Devices
• Solar/Wind Source Converters