CCNA 3 v7.

0 Modules 1 – 2: OSPF Concepts

and Configuration Exam Answers
1. What is a function of OSPF hello packets?
to send specifically requested link-state records
to discover neighbors and build adjacencies between them*
to ensure database synchronization between routers
to request specific link-state records from neighbor routers
2. Which OPSF packet contains the different types of link-
state advertisements?
hello
DBD
LSR
LSU*
LSAck
3. Which three statements describe features of the OSPF
topology table? (Choose three.)
It is a link-state database that represents the network topology.*
Its contents are the result of running the SPF algorithm.
When converged, all routers in an area have identical topology tables.*
The topology table contains feasible successor routes.
The table can be viewed via the show ip ospf database command.*
After convergence, the table only contains the lowest cost route entries for all known
networks.
4. What does an OSPF area contain?
routers that share the same router ID
routers whose SPF trees are identical
routers that have the same link-state information in their LSDBs*
routers that share the same process ID
5. What is used to facilitate hierarchical routing in OSPF?
the use of multiple áreas*
frequent SPF calculations
autosummarization
the election of designated routers
Explanation: OSPF supports the concept of areas to prevent larger routing tables,
excessive SPF calculations, and large LSDBs. Only routers within an area share
link-state information. This allows OSPF to scale in a hierarchical fashion with all
areas that connect to a backbone area.
6. Which OSPF data structure is identical on all OSPF routers
that share the same area?
forwarding database
link-state database*
adjacency database
routing table
Explanation: Regardless of which OSPF area a router resides in, the adjacency
database, routing table, and forwarding database are unique for each router. The
link-state database lists information about all other routers within an area and is
identical across all OSPF routers participating in that area.
7. Which step does an OSPF-enabled router take immediately
after establishing an adjacency with another router?
builds the topology table
exchanges link-state advertisements*
chooses the best path
executes the SPF algorithm
Explanation: The OSPF operation steps are as follows:
1. Establish neighbor adjacencies
2. Exchange link-state advertisements
3. Build the topology table
4. Execute the SPF algorithm
5. Choose the best route
8. A network engineer has manually configured the hello
interval to 15 seconds on an interface of a router that is
running OSPFv2. By default, how will the dead interval on the
interface be affected?
The dead interval will not change from the default value.
The dead interval will now be 30 seconds.
The dead interval will now be 60 seconds.*
The dead interval will now be 15 seconds.
Explanation: Cisco IOS automatically modifies the dead interval to four times the
hello interval.
9. Refer to the exhibit.
 CCNA 3 v7.0 Modules 1 – 2 Exam Answers p9
A network administrator has configured the OSPF timers to
the values that are shown in the graphic. What is the result of
having those manually configured timers?
R1 automatically adjusts its own timers to match the R2 timers.
The R1 dead timer expires between hello packets from R2.*
The hello timer on R2 expires every ten seconds.
The neighbor adjacency has formed.
Explanation: The dead timer (20 seconds) on R1 expires before the next hello
packet from R2 (25 seconds).
10. To establish a neighbor adjacency two OSPF routers will
exchange hello packets. Which two values in the hello packets
must match on both routers? (Choose two.)
dead interval*
router priority
list of neighbors
router ID
hello interval*
Explanation: The hello and dead interval timers contained in a hello packet must be
the same on neighboring routers in order to form an adjacency.
11. What is the default router priority value for all Cisco
OSPF routers?
0
1*
10
255
Explanation: The router priority value is used in a DR/BDR election. The default
priority for all OSPF routers is 1 but it can be manually altered to any value 0 to
255.
12. Which type of OSPFv2 packet contains an abbreviated list
of the LSDB of a sending router and is used by receiving
routers to check against the local LSDB?
database description*
link-state update
link-state request
link-state acknowledgment
Explanation: The database description (DBD) packet contains an abbreviated list of
the LSDB sent by a neighboring router and is used by receiving routers to check
against the local LSDB.
13. In an OSPF network when are DR and BDR elections
required?
when the two adjacent neighbors are interconnected over a point-to-point link
when all the routers in an OSPF area cannot form adjacencies
when the routers are interconnected over a common Ethernet network*
when the two adjacent neighbors are in two different networks
Explanation: When the routers are interconnected over a common Ethernet
network, then a designated router (DR) and a backup DR (BDR) must be elected.
14. When an OSPF network is converged and no network
topology change has been detected by a router, how often will
LSU packets be sent to neighboring routers?
every 5 minutes
every 10 minutes
every 30 minutes*
every 60 minutes
Explanation: After all LSRs have been satisfied for a given router, the adjacent
routers are considered synchronized and in a full state. Updates (LSUs) are sent to
neighbors only under the following conditions:
when a network topology change is detected (incremental updates)
every 30 minutes
15. What will an OSPF router prefer to use first as a router
ID?
a loopback interface that is configured with the highest IP address on the router
any IP address that is configured using the router-id command*
the highest active interface IP that is configured on the router
the highest active interface that participates in the routing process because of a
specifically configured network statement
Explanation: The first preference for an OSPF router ID is an explicitly configured
32-bit address. This address is not included in the routing table and is not defined by
the network command. If a router ID that is configured through the router-
id command is not available, OSPF routers next use the highest IP address available
on a loopback interface, as loopbacks used as router IDs are also not routable
addresses. Lacking either of these alternatives, an OSPF router will use the highest
IP address from its active physical interfaces.
16. What are the two purposes of an OSPF router ID? (Choose
two.)
to uniquely identify the router within the OSPF domain*
to facilitate router participation in the election of the designated router*
to enable the SPF algorithm to determine the lowest cost path to remote networks
to facilitate the establishment of network convergence
to facilitate the transition of the OSPF neighbor state to Full
Explanation: OSPF router ID does not contribute to SPF algorithm calculations,
nor does it facilitate the transition of the OSPF neighbor state to Full. Although the
router ID is contained within OSPF messages when router adjacencies are being
established, it has no bearing on the actual convergence process.
17. Refer to the exhibit.

CCNA 3 v7.0 Modules 1 – 2 Exam Answers p17

If no router ID was manually configured, what would router
Branch1 use as its OSPF router ID?
10.0.0.1
10.1.0.1
192.168.1.100*
209.165.201.1
Explanation: In OSPFv2, a Cisco router uses a three-tier method to derive its router
ID. The first choice is the manually configured router ID with the router-
id command. If the router ID is not manually configured, the router will choose the
highest IPv4 address of the configured loopback interfaces. Finally if no loopback
interfaces are configured, the router chooses the highest active IPv4 address of its
physical interfaces.
18. A network technician issues the following commands when
configuring a router:
R1(config)# router ospf 11
R1(config-router)# network 10.10.10.0 0.0.0.255 area 0

What does the number 11 represent?

the OSPF process ID on R1*
the cost of the link to R1
the autonomous system number to which R1 belongs
the administrative distance that is manually assigned to R1
the area number where R1 is located
Explanation: There is no autonomous system number to configure on OSPF. The
area number is located at the end of the network statement. The cost of a link can be
modified in the interface configuration mode. The process ID is local to the router.
19. An OSPF router has three directly connected networks;
172.16.0.0/16, 172.16.1.0/16, and 172.16.2.0/16. Which OSPF
network command would advertise only the 172.16.1.0
network to neighbors?
router(config-router)# network 172.16.1.0 0.0.255.255 area 0*
router(config-router)# network 172.16.0.0 0.0.15.255 area 0
router(config-router)# network 172.16.1.0 255.255.255.0 area 0
router(config-router)# network 172.16.1.0 0.0.0.0 area 0
Explanation: To advertise only the 172.16.1.0/16 network the wildcard mask used
in the network command must match the first 16-bits exactly. To match bits exactly,
a wildcard mask uses a binary zero. This means that the first 16-bits of the wildcard
mask must be zero. The low order 16-bits can all be set to 1.
20. Refer to the exhibit.
 CCNA 3 v7.0 Modules 1 – 2 Exam Answers p20
Which three statements describe the results of the OSPF
election process of the topology that is shown in the exhibit?
(Choose three.)
R3 will be elected BDR.*
The R4 FastEthernet 0/0 priority is 128.
The R4 router ID is 172.16.1.1.*
R1 will be elected BDR.
The router ID on R2 is the loopback interface.
R2 will be elected DR.*
Explanation: R2 will be elected DR because it has the highest priority of 255, all of
the others have a priority of 1. R3 will be elected BDR because it has the
numerically highest router-ID of 192.168.1.4. The R4 router-ID is 172.16.1.1
because it is the IPv4 address attached to the loopback 0 interface.
21. Refer to the exhibit.
 CCNA 3 v7.0 Modules 1 – 2 Exam Answers p21
If the switch reboots and all routers have to re-establish OSPF
adjacencies, which routers will become the new DR and BDR?
Router R4 will become the DR and router R1 will become the BDR.*
Router R2 will become the DR and router R3 will become the BDR.
Router R1 will become the DR and router R2 will become the BDR.
Router R4 will become the DR and router R3 will become the BDR.
Explanation: OSPF elections of a DR are based on the following in order of
precedence:
highest pritority from 1 -255 (0 = never a DR)
highest router ID
highest IP address of a loopback or active interface in the absence of a manually
configured router ID. Loopback IP addresses take higher precedence than other
interfaces.
In this case routers R4 and R1 have the highest router priority. Between the two, R3
has the higher router ID. Therefore, R4 will become the DR and R1 will become the
BDR.
22. By default, what is the OSPF cost for any link with a
bandwidth of 100 Mb/s or greater?
100000000
10000
1*
100
Explanation: OSPF uses the formula: Cost = 100,000,000 / bandwidth. Because
OSPF will only use integers as cost, any bandwidth of 100 Mb/s or greater will all
equal a cost of 1.
23. Refer to the exhibit.

CCNA 3 v7.0 Modules 1 – 2 Exam Answers p23

What is the OSPF cost to reach the router A LAN
172.16.1.0/24 from B?
782
74
128
65*
Explanation: The formula used to calculate the OSPF cost is as follows:
Cost = reference bandwidth / interface bandwidth
The default reference bandwidth is 10^8 (100,000,000); therefore, the formula is
Cost = 100,000,000 bps / interface bandwidth in bps
Thus the cost to reach the A LAN 172.16.1.0/24 from B is as follows:
Serial link (1544 Kbps) from B to A cost => 100,000,000 / 1,544,000 = 64
Gigabit Ethernet link on A cost => 100,000,000 / 1,000,000,000 = 1
Total cost to reach 172.16.1.0/24 = 64 + 1 = 65
24. Refer to the exhibit.

CCNA 3 v7.0 Modules 1 – 2 Exam Answers p24

On which router or routers would a default route be statically
configured in a corporate environment that uses single area
OSPF as the routing protocol?
R0-A*
ISP, R0-A, R0-B, and R0-C
ISP
R0-B and R0-C
ISP and R0-A
R0-A, R0-B, and R0-C
Explanation: The default route is applied to the router that connects to the Internet,
or R0-A. R0-A then distributes that default route using the OSPF routing protocol.
25. What command would be used to determine if a routing
protocol-initiated relationship had been made with an
adjacent router?
ping
show ip ospf neighbor*
show ip interface brief
show ip protocols
Explanation: While the show ip interface brief and ping commands can be used to
determine if Layer 1, 2, and 3 connectivity exists, neither command can be used to
determine if a particular OSPF or EIGRP-initiated relationship has been made.
The show ip protocols command is useful in determining the routing parameters
such as timers, router ID, and metric information associated with a specific routing
protocol. The show ip ospf neighbor command shows if two adjacent routers have
exchanged OSPF messages in order to form a neighbor relationship.
26. Refer to the exhibit.

CCNA 3 v7.0 Modules 1 – 2 Exam Answers p26

Which command did an administrator issue to produce this
output?
R1# show ip ospf interface serial0/0/1*
R1# show ip route ospf
R1# show ip ospf
R1# show ip ospf neighbor
27. Which command is used to verify that OSPF is enabled
and also provides a list of the networks that are being
advertised by the network?
show ip interface brief
show ip ospf interface
show ip protocols*
show ip route ospf
Explanation: The command show ip ospf interface verifies the active OSPF
interfaces. The command show ip interface brief is used to check that the interfaces
are operational. The command show ip route ospf displays the entries that are
learned via OSPF in the routing table. The command show ip protocols checks that
OSPF is enabled and lists the networks that are advertised.
28. Refer to the exhibit.

CCNA 3 v7.0 Modules 1 – 2 Exam Answers p28

A network administrator has configured OSPFv2 on the two
Cisco routers but PC1 is unable to connect to PC2. What is the
most likely problem?
Interface Fa0/0 has not been activated for OSPFv2 on router R2.*
Interface Fa0/0 is configured as a passive-interface on router R2.
Interface S0/0 is configured as a passive-interface on router R2.
Interface s0/0 has not been activated for OSPFv2 on router R2.
Explanation: If a LAN network is not advertised using OSPFv2, a remote network
will not be reachable. The output displays a successful neighbor adjacency between
router R1 and R2 on the interface S0/0 of both routers.
29. What is the recommended Cisco best practice for
configuring an OSPF-enabled router so that each router can
be easily identified when troubleshooting routing issues?
Configure a value using the router-id command.*
Use the highest active interface IP address that is configured on the router.
Use a loopback interface configured with the highest IP address on the router.
Use the highest IP address assigned to an active interface participating in the routing
process.
Explanation: A Cisco router is assigned a router ID to uniquely identify it. It can be
automatically assigned and take the value of the highest configured IP address on
any interface, the value of a specifically-configured loopback address, or the value
assigned (which is in the exact form of an IP address) using the router-id command.
Cisco recommends using the router-id command.
30. Which step in the link-state routing process is described by
a router running an algorithm to determine the best path to
each destination?
load balancing equal-cost paths
declaring a neighbor to be inaccessible
choosing the best route
executing the SPF algorithm*
31. An administrator is configuring single-area OSPF on a
router. One of the networks that must be advertised is
192.168.223.0 255.255.254.0. What wildcard mask would the
administrator use in the OSPF network statement?
0.0.1.255*
0.0.7.255
0.0.15.255
0.0.31.255
32. What is the format of the router ID on an OSPF-enabled
router?
a unique router host name that is configured on the router
a unique phrase with no more than 16 characters
a 32-bit number formatted like an IPv4 address*
an 8-bit number with a decimal value between 0 and 255
a character string with no space
Explanation: A router ID is a 32-bit number formatted like an IPv4 address and
assigned in order to uniquely identify a router among OSPF peers.
33. Question as presented:
DUAL is the algorithm used by EIGRP. In multiarea OSPF, OSPF is implemented
using multiple areas, and all of them must be connected to the backbone area.

34. After modifying the router ID on an OSPF router, what is

the preferred method to make the new router ID effective?
HQ# copy running-config startup-config
HQ# resume
HQ# clear ip route
HQ# clear ip ospf process*
Explanation: To modify a router-id on an OSPF-enabled router, it is necessary to
reset the OSPF routing process by entering either the clear ip ospf process command
or the reload command.
35. In an OSPFv2 configuration, what is the effect of entering
the command network 192.168.1.1 0.0.0.0 area 0?
It allows all 192.168.1.0 networks to be advertised.
It tells the router which interface to turn on for the OSPF routing process.*
It changes the router ID of the router to 192.168.1.1.
It enables OSPF on all interfaces on the router.
Explanation: Entering the command network 192.168.1.1 0.0.0.0 area 0 will turn
on only the interface with that IP address for OSPF routing. It does not change the
router ID. Instead, OSPF will use the network that is configured on that interface.
36. What is the reason for a network engineer to alter the
default reference bandwidth parameter when configuring
OSPF?
to force that specific link to be used in the destination route
to more accurately reflect the cost of links greater than 100 Mb/s*
to enable the link for OSPF routing
to increase the speed of the link
Explanation: By default, Fast Ethernet, Gigabit, and 10 Gigabit Ethernet interfaces
all have a cost of 1. Altering the default reference bandwidth alters the cost
calculation, allowing each speed to be more accurately reflected in the cost.
37. Open the PT Activity. Perform the tasks in the activity
instructions and then answer the question.
Which task has to be performed on Router 1 for it to establish
an OSPF adjacency with Router 2?
Issue the clear ip ospf process command.
Change the subnet mask of interface FastEthernet 0/0 to 255.255.255.0.*
Remove the passive interface command from interface FastEthernet 0/0.
Add the network 10.0.1.0 0.0.0.255 area 0 command to the OSPF process.
Explanation: Each interface on the link connecting the OSPF routers must be in the
same subnet for an adjacency to be established. The IP address subnet mask on
FastEthernet interface 0/0 must be changed to 255.255.255.0. The FastEthernet
interface 0/0 is not passive. The 10.0.1.0/24 network is only connected to Router2 so
should not be advertised by Router1. The clear ip ospf process command will start
the OPSF process on Router1 but will not cause an adjacency to be established if the
subnet mask mismatch on the connecting interfaces still exists.
38. Match the description to the term. (Not all options are
used.)
 CCNA 3 v7.0 Modules 1 – 2 Exam Answers p38
39. What is a benefit of multiarea OSPF routing?
Topology changes in one area do not cause SPF recalculations in other areas.*
Routers in all areas share the same link-state database and have a complete picture
of the entire network.
A backbone area is not required.
Automatic route summarization occurs by default between areas.
Explanation: With multiarea OSPF, only routers within an area share the same link-
state database. Changes to the network topology in one area do not impact other
areas, which reduces the number of SPF algorithm calculations and the of link-state
databases.
40. Match the OSPF state with the order in which it occurs.
(Not all options are used.)
 CCNA 3 v7.0 Modules 1 – 2 Exam Answers p40
41. What indicates to a link-state router that a neighbor is
unreachable?
if the router no longer receives hello packets*
if the router receives an update with a hop count of 16
if the router receives an LSP with previously learned information
if the router no longer receives routing updates
Explanation: OSPF routers send hello packets to monitor the state of a neighbor.
When a router stops receiving hello packets from a neighbor, that neighbor is
considered unreachable and the adjacency is broken.
42. Which three OSPF states are involved when two routers
are forming an adjacency? (Choose three.)
Exchange
Init*
ExStart
Two-way*
Loading
Down*
Explanation: OSPF operation progresses through 7 states for establishing
neighboring router adjacency, exchanging routing information, calculating the best
routes, and reaching convergence. The Down, Init, and Two-way states are involved
in the phase of neighboring router adjacency establishment.
43. Refer to the exhibit.
 CCNA 3 v7.0 Modules 1 – 2 Exam Answers p43
Suppose that routers B, C, and D have a default priority, and
router A has a priority 0. Which conclusion can be drawn
from the DR/BDR election process?
If the priority of router C is changed to 255, then it will become the DR.
Router A will become the DR and router D will become the BDR.
If the DR fails, the new DR will be router B.*
If a new router with a higher priority is added to this network, it will become the
DR.
Explanation: If the priority is set to 0, the router is not capable of becoming the DR,
so router A cannot be the DR. OSPF DR and BDR elections are not preemptive. If a
new router with a higher priority or higher router ID is added to the network after
the DR and BDR election, the newly added router does not take over the DR or the
BDR role.
44. An administrator is configuring single-area OSPF on a
router. One of the networks that must be advertised is
64.102.0.0 255.255.255.128. What wildcard mask would the
administrator use in the OSPF network statement?
0.0.31.255
0.0.0.63
0.0.63.255
0.0.0.127*
45. Which command will a network engineer issue to verify
the configured hello and dead timer intervals on a point-to-
point WAN link between two routers that are running
OSPFv2?
show ipv6 ospf interface serial 0/0/0
show ip ospf neighbor
show ip ospf interface fastethernet 0/1
show ip ospf interface serial 0/0/0*
Explanation: The show ip ospf interface serial 0/0/0 command will display the
configured hello and dead timer intervals on a point-to-point serial WAN link
between two OSPFv2 routers. The show ipv6 ospf interface serial 0/0/0 command
will display the configured hello and dead timer intervals on a point-to-point serial
link between two OSPFv3 routers. The show ip ospf interface fastethernet 0/1
command will display the configured hello and dead timer intervals on a multiaccess
link between two (or more) OSPFv2 routers. The show ip ospf neighbor command
will display the dead interval elapsed time since the last hello message was received,
but does not show the configured value of the timer.
46. An administrator is configuring single-area OSPF on a
router. One of the networks that must be advertised is
128.107.0.0 255.255.255.192. What wildcard mask would the
administrator use in the OSPF network statement?
0.0.63.255
0.0.0.63*
0.0.0.3
0.0.0.7
47. Match each OSPF packet type to how it is used by a
router. (Not all options are used.)
 CCNA 3 v7.0 Modules 1 – 2 Exam Answers p47
48. Which step in the link-state routing process is described by
a router building a link-state database based on received
LSAs?
building the topology table*
49. Which three OSPF states are involved when two routers
are forming an adjacency? (Choose three.)
Init*
Two-way*
Down*
50. An administrator is configuring single-area OSPF on a
router. One of the networks that must be advertised is
198.19.0.0 255.255.252.0. What wildcard mask would the
administrator use in the OSPF network statement?
0.0.63.255
0.0.3.255*
0.0.31.255
0.0.0.255
51. An administrator is configuring single-area OSPF on a
router. One of the networks that must be advertised is
128.107.0.0 255.255.252.0. What wildcard mask would the
administrator use in the OSPF network statement?
0.0.3.255*
0.0.0.7
0.0.0.3
0.0.63.255