Scribd
Upload
196 views

TLE EIM Worksheet 1

This document provides instructions for a self-directed learning module on preparing and using electrical and hydraulic power tools. It includes: 1) Objectives to identify common power tools and hydraulic tools used in electrical installation. 2) A vocabulary list defining terms like accuracy, amperage, bender, calibration, and hydraulic oil. 3) A pre-test to label parts of a portable electric drill. 4) Learning activities that describe safety procedures and multiple choice questions about using a portable electric drill.

Uploaded by

Jerome Ayala Bermundo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
196 views

TLE EIM Worksheet 1

This document provides instructions for a self-directed learning module on preparing and using electrical and hydraulic power tools. It includes: 1) Objectives to identify common power tools and hydraulic tools used in electrical installation. 2) A vocabulary list defining terms like accuracy, amperage, bender, calibration, and hydraulic oil. 3) A pre-test to label parts of a portable electric drill. 4) Learning activities that describe safety procedures and multiple choice questions about using a portable electric drill.

Uploaded by

Jerome Ayala Bermundo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

TLE-EIM-9

(Auburn, Boysenberry, Mauve, Moccasin, Periwinkle, Ochre, OHSP)

FOR SELF-DIRECTED MODULES/ACTIVITY SHEETS

I. Title of Material/Introduction: – Module 1: Preparing Electrical Power and Hydraulic Tools

II. Objectives: At the end of this lesson, you will be able to: a) Identify Power Tools and
Hydraulic Tools commonly used in electrical installation

III. Vocabulary List:

Accuracy -means how near the instrument reading is to the actual value.

Amperage-means electricity; electrical current flow; electron flow; must be measured at a point
within a circuit.

Bender-is a tool used to make various angles or bends in conduit.

Calibration-is a technique of testing and adjusting an instrument by referring to another


instrument or device of known accuracy and precision.

Chuck-is a portion of drill that holds the bit.

Cross handle-is the handle set across a power tool to prevent the tool from burning.

Cutter-is a hardened steel device used to cut holes in metal boxes.

Die-is a component that bucks up cutter on opposite side of metal box.

Cold-is the absence of heat; a temperature considerably below normal

Ground-is an electrical point or any good conductor that is connected to a common chassis with
zero relative voltage; usually conductors are connected to the earth.

Hydraulic-is using pressurized fluid oil to accomplish work.

Hydraulic oil-is specially formulated oil for hydraulic pumps.


NOTE: No oil or fluid should ever be substitute for hydraulic oil.

Knockout punch-is a device used to make openings for conduit in metal enclosures

Ram-is a device used to transfer hydraulic pressure to a mechanical device


IV. Pre-Test: Direction: Identify the position of the parts of portable electric drill. Write the
number of its position on the space before each letter.

A. Chuck

B. Chuck Wrench

C. Cord Strain Relievers

D. Electrical Cord

E. Piston Grip

F. Reversing Switch

G. Switch Lock

H. Trigger Switch

V. Learning Activities: A. Read the Safety and Procedure in using Portable Hand Drill B.
Answer the Multiple Choice
Portable Electric Drill Safety

1. Wear safety glasses when operating with portable electric drill.


2. Disconnect the drill from the electrical supply when installing bits.
3. Clamp stock so it will not move during the drilling operation.
4. Before drilling, turn the drill on to see if the bit is centered and running true.
5. Align the bit with the desired hole location before turning the drill on.
6. Hold the drill firmly with both hands while drilling.
7. When drilling deep holes with a twist drill, move the bit up and down several times while drilling
to remove cuttings and reduce overheating in the bit.
8. Do not allow the cord to become wrapped around the drill when working.
9. If the electrical cord becomes frayed or starts to separate from the drill housing, repair it
immediately!
10. Remove the bit from the drill as soon as the work is completed.
11. Select the correct bit for the finish and material being drilled. Make sure the bit is securely
tightened in the drill chuck.
12. Be extremely careful when using larger portable electric drills (3/8" and 1/2"). If the bit should
hang or get caught the drill will twist in the operator’s hands causing a sprain or bruised fingers.
13. Always remove the key from the chuck before drilling.
14. To prevent seizing, reduce the feed pressure when the drill bit is about to come through the
material.
Procedures in using Portable Hand Drill
1. Always center punch or make a starting indentation in the material being drilled to get an
accurate starting point for the drill bit.
2. Tighten the drill bit by rotating the chuck key to all three holes in the chuck. This will help to
keep the drill bit centered.
3. Use only straight shank or Silver and Deming drill bits in portable electric drills.
4. Apply moderate even pressure to the drill during the drilling operation. If excessive pressure is
required to make the bit cut then the bit is dull and needs to be sharpened.
5. Maintain good balance at all times when drilling.
6. Use slow drill speeds for drilling metal and fast speeds for drilling wood. To obtain holes that are
placed accurately, drill a small pilot first then drill the final hole.

Portable Electric Drill Safety and Procedure Test

Name _________________________ Date___________________ Grade/Sec:____________


Multiple Choice: Write the letter of the most correct answer on your answer sheet.

1. The purpose of turning the drill on before attempting to drill a hole is to ____.
a. see if the drill operates.
b. see if the drill bit is running true.
c. make sure the chuck key has been removed.
d. check if the power cord is good
2. The purpose of moving the drill and bit up and down often when drilling deep hole is to
__________________.
a. ream the hole slightly larger.
b. give the drill operator better drilling leverage.
c. help keep the hole centered.
d. reduce overheating in the drill bit.
3. If a large capacity portable drill bit hangs during the drilling operation what will likely to happen?
a. The bit will break.
b. The drill will twist in the operator's hands causing a sprained wrist or bruised fingers.
c. The drill will likely stall out and overheat.
d. The hole will become badly distorted.
4. The purpose of a pilot hole when drilling is to ____________.
a. make the final hole drilling operation easier.
b. guide the final drilling operation and achieve a more accurately place hole.
c. reduce the feed pressure needed to drill the hole.
d. allow the final hole to be drilled at a faster rpm and achieve a smoother
e. finish.
5. To prevent seizing when drilling, the operator should ____________.
a. reduce the rpms of the portable electric drill
b. lubricate the drill bit.
c. use a high-speed drill bit.
reduce the feed pressure when the bit is about to come through the
material being drilled.

You might also like