Ordering number : EN4585A
Thick Film Hybrid IC
STK4211V
2-Channel 70 W min AF Power Amplifier
(Split Power Supply)
Features Package Dimensions
• The inclusion of a muting circuit on-chip allows all unit: mm
types of impulse noise to be excluded. 4086A
• Current mirror circuit application reduces distortion to
0.008%. [STK4211V]
• Pin compatible with the STK4201II Series (THD = 0.4%)
and the STK4141X Series (THD = 0.02%)
Specifications
Maximum Ratings at Ta = 25°C
Parameter Symbol Condition Rating Unit
Maximum supply voltage VCC max ±62 V
Thermal resistance θj-c 1.5 °C/W
Junction temperature Tj 150 °C
Operating case temperature Tc 125 °C
Storage temperature Tstg –30 to +125 °C
Available time for load shorted tS* VCC = ±43 V, RL = 8 Ω, f = 50 Hz, PO = 70 W 1 sec
Note: Use a constant voltage power supply as the test power supply unless otherwise specified.
* Use the transformer power supply shown on the next page when measuring the available time for load shorted and the output noise voltage.
Recommended Operating Conditions at Ta = 25°C
Parameter Symbol Condition Rating Unit
Recommended supply voltage VCC ±43 V
Load resistance RL 8 Ω
SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN
61096HA (OT)/52493YO 5-2377 No. 4585-1/3
STK4211V
Operating Characteristics at Ta = 25°C, VCC = ±43 V, RL = 8 Ω (noninductive load), RG = 600 Ω, VG = 40 dB
Rating
Parameter Symbol Condition Unit
min typ max
Quiescent current ICCO VCC = ±50.5 V 20 40 100 mA
Output power PO THD = 0.08%, f = 20 Hz to 20 kHz 70 W
Total harmonic distortion THD PO = 1.0 W, f = 1 kHz 0.08 %
+0
Frequency response fL, fH PO = 1.0 W, –3 dB 20 to 50 k Hz
Input resistance ri PO = 1.0 W, f = 1 kHz 55 kΩ
Output noise voltage VNO* VCC = ±50.5 V, Rg = 10 kΩ 1.2 mVrms
Neutral voltage VN VCC = ±50.5 V –70 0 +70 mV
Muting voltage VM –2 –5 –10 V
Note: Use a constant voltage power supply as the test power supply unless otherwise specified.
* The output noise voltage is the peak value measured with an averaging rms scale volt meter. The noise voltage waveform should not include
pulse noise.
Specified Transformer Power Supply
(MG-200 equivalent)
Equivalent Circuit
No. 4585-2/3
STK4211V
Sample Application Circuit: 2-Channel 70 W min AF Power Amplifier
Unit (resistance: Ω, capacitance: F)
■ No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace
equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of
which may directly or indirectly cause injury, death or property loss.
■ Anyone purchasing any products described or contained herein for an above-mentioned use shall:
➀ Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and
distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all
damages, cost and expenses associated with such use:
➁ Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on
SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees
jointly or severally.
■ Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for
volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied
regarding its use or any infringements of intellectual property rights or other rights of third parties.
This catalog provides information as of November, 1997. Specifications and information herein are subject to
change without notice.
No. 4585-3/3
