Technical Data
Valspar Protective Coatings
1101 S. 3rd Street
Minneapolis MN 55415
[email protected] www.valsparindustrial.com
4-10-2017
702G Internal Pipe Coating System
702G is a thermosetting epoxy powder coating engineered for use inside pipelines. It is typically applied
over phenolic primers such as Valspar Pipeclad HXR0015 or HXR0016.
Specifications Test Standard
Color Green Visual Color-Pass
Gel Time @ 204°C (400°F) 45-75 seconds
D10 7-11 µm
Particle Size
D90 100-155 µm
325 Mesh Sieve Retention (%) 45-55
Tg1 55-65 °C
Thermal Properties CSA Z245.20-10 (12-7)
Tg2 115-125 °C
Plate Flow at 300 °F (149 °C) 65 – 95 mm
Moisture Content (%) 0 – 0.5
Specific Gravity 1.53 – 1.63
Additional Information
Recommended Service: Characteristics:
High temperature drill pipe Primer: Phenolic Primer
Oil, gas and water wells Thickness: 250-500 µm
Rod pump wells Use Temperature to 150 °C (302°F)
Gas lift
Powder Properties
Specific Gravity 1.58
Coverage 0.633 m2/kg per mm (122 ft2/lb per mil)
Shelf Life at 77 °F (25 °C) and 50% Relative 12 months
Humidity
Storage and Handling Store below 27°C (80°F) and 50%
relative humidity
© 2017 Valspar. All rights reserved. VALSPAR and PIPECLAD are trademarks of The Valspar Corporation. The data on this sheet represent typical values. Since application variables are a major factor in product
performance, this information should serve only as a general guide. Valspar assumes no obligation or liability for use of this information. UNLESS VALSPAR AGREES OTHERWISE IN WRITING, VALSPAR MAKES
NO WARRANTIES, EXPRESS OR IMPLIED, AND DISCLAIMS ALL IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR FREEDOM FROM PATENT
INFRINGEMENT. VALSPAR WILL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Your only remedy for any defect in this product is the replacement of the defective product, or
a refund of its purchase price, at our option. This information in this sheet (if marked as "Confidential"), as well as the products referenced herein, shall be considered "Confidential Information" pursuant to the
Coatings Supply Agreement. Wet samples and uncured samples of these products shall be maintained as confidential and shall not be disclosed to any third party without the prior written permission of Valspar.
Form: 01-0007-04162014-NA
Applied Film Properties Specification Test Method
Abrasion-Taber Average weight ASTM D4060 (CS-17 wheels and 1000 g load
loss 17 mg at 1000 cycles)
Impact (in-lb//J) 23°C/74°F 40/4.5
Gouge (% coating loss/% retention)
SL-1 blank bit
0 kg 14/86
10 kg 31/69
20 kg 63/37
SL-1 single cut bit
0 kg 31/69
Flexibility (RT) 1.5 degrees/PD
Coefficient of Friction 28 ASTM D202 (Slide angle °)
0.440/0.462 ASTM D1894 (Kinetic/Static)
702G Gel and Cure Guide
Gel Time Graph Measured by Modified ISO 8130-6
702G Gel Time
250
225
200
Gel Time (Seconds)
175
150
125
100
75
50
25
0
350 375 400 425
Temperature (°F)
© 2017 Valspar. All rights reserved. VALSPAR and PIPECLAD are trademarks of The Valspar Corporation. The data on this sheet represent typical values. Since application variables are a major factor in product
performance, this information should serve only as a general guide. Valspar assumes no obligation or liability for use of this information. UNLESS VALSPAR AGREES OTHERWISE IN WRITING, VALSPAR MAKES
NO WARRANTIES, EXPRESS OR IMPLIED, AND DISCLAIMS ALL IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR FREEDOM FROM PATENT
INFRINGEMENT. VALSPAR WILL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Your only remedy for any defect in this product is the replacement of the defective product, or
a refund of its purchase price, at our option. This information in this sheet (if marked as "Confidential"), as well as the products referenced herein, shall be considered "Confidential Information" pursuant to the
Coatings Supply Agreement. Wet samples and uncured samples of these products shall be maintained as confidential and shall not be disclosed to any third party without the prior written permission of Valspar.
Form: 01-0007-04162014-NA
Minimum Cure Time Graph
702G Minimum Cure Time
90
80
70
Cure Time (Minutes)
60
50
40
30
20
10
0
400 425 450 475
Metal Temperature (°F)
Peak Metal Temperature Typical Gel Time Cure Time
218 °C (425 °F) 30 seconds 45 minutes
204 °C (400 °F) 55 seconds 60 minutes
Application Guidelines and Sequence
1. Blast clean to white metal with a nominal 50 µm (2 mil) profile height.
2. Apply phenolic primer to dry film thickness of 17-25 µm (0.7-1.0 mil.)
3. Preheat to 149-177 °C (300-350°F) (metal temperature) to cure the primer.
4. Apply powder coating to the specified film thickness (250-500 µm/10-20 mil)
5. Post cure based on the Minimum Cure Time recommendations in the graph above. For example,
at least 20 minutes above 232°C (450°F) metal temperature, or 40 minutes above 218°C (425°F).
Extended post cure time or higher post cure temperatures than the recommended minimum
increases chemical resistance, but may also embrittle the coating.
6. Cool in air to room temperature.
Important Note: Cure times vary depending on line conditions. Establish optimum curing conditions for your line
by testing.
© 2017 Valspar. All rights reserved. VALSPAR and PIPECLAD are trademarks of The Valspar Corporation. The data on this sheet represent typical values. Since application variables are a major factor in product
performance, this information should serve only as a general guide. Valspar assumes no obligation or liability for use of this information. UNLESS VALSPAR AGREES OTHERWISE IN WRITING, VALSPAR MAKES
NO WARRANTIES, EXPRESS OR IMPLIED, AND DISCLAIMS ALL IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR FREEDOM FROM PATENT
INFRINGEMENT. VALSPAR WILL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Your only remedy for any defect in this product is the replacement of the defective product, or
a refund of its purchase price, at our option. This information in this sheet (if marked as "Confidential"), as well as the products referenced herein, shall be considered "Confidential Information" pursuant to the
Coatings Supply Agreement. Wet samples and uncured samples of these products shall be maintained as confidential and shall not be disclosed to any third party without the prior written permission of Valspar.
Form: 01-0007-04162014-NA
Autoclave Performance Tests*
Temperature Pressure Medium Duration Results
149°C(300 °F) 6,500 psig 3% CO2 / 97% CH4 16 hours Pass
50% Toluene / 50%
Kerosene
Brine
135°C(275 °F) 5,000 psig 1% H2S / 20% CO2 / 79% CH4 16 hours Pass
50% Toluene / 50%
Kerosene
Brine
135°C(275 °F) 6,500 psig 3% H2S / 3% CO2 / 10% CH4/ 72 hours Pass
N2
Lime Mud
149°C(300 °F) 10,000 psig 3% CO2 / 97% N2 16 hours Pass
Instant decompression
95°C (203 °F) 3,000 psig Gas phase: N2 24 hours No loss of
09-SAMSS-091 Liquid phase: Treated sea adhesion, no
Appendix 3.5 water swelling, softening
and blistering
95°C (203°F) 3,000 psig Gas phase: 3% CO2, 3% H2S, 24 hours No loss of
09-SAMSS-091 94% CH4 adhesion, no
Appendix 3.5 Liquid phase: Formation swelling, softening
water brine and blistering
95°C (203°F) 3,000 psig Gas phase: CO2 24 hours No loss of
09-SAMSS-091 Liquid phase: Wasia water adhesion, no
Appendix 3.5 swelling, softening
and blistering
50°C (122°F) Covered 10% Vol. HCl 24 hours No loss of
09-SAMSS-091 Vented adhesion, no
Appendix 3.5 Container swelling, softening
and blistering
*These tests results are based on laboratory simulations of field conditions and should serve only as a general guide. Test results may not accurately
predict field performance.
© 2017 Valspar. All rights reserved. VALSPAR and PIPECLAD are trademarks of The Valspar Corporation. The data on this sheet represent typical values. Since application variables are a major factor in product
performance, this information should serve only as a general guide. Valspar assumes no obligation or liability for use of this information. UNLESS VALSPAR AGREES OTHERWISE IN WRITING, VALSPAR MAKES
NO WARRANTIES, EXPRESS OR IMPLIED, AND DISCLAIMS ALL IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR FREEDOM FROM PATENT
INFRINGEMENT. VALSPAR WILL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. Your only remedy for any defect in this product is the replacement of the defective product, or
a refund of its purchase price, at our option. This information in this sheet (if marked as "Confidential"), as well as the products referenced herein, shall be considered "Confidential Information" pursuant to the
Coatings Supply Agreement. Wet samples and uncured samples of these products shall be maintained as confidential and shall not be disclosed to any third party without the prior written permission of Valspar.
Form: 01-0007-04162014-NA
