MiCOM P442 & P444

Software Version C3.7

Hardware Suffix J

PICS and MICS

P44x/EN PM/A11
Note: The technical manual for this device gives instructions for its installation, commissioning, and operation.
However, the manual cannot cover all conceivable circumstances or include detailed information on all
topics. In the event of questions or specific problems, do not take any action without proper authorization.
Contact the appropriate AREVA technical sales office and request the necessary information.

Any agreements, commitments, and legal relationships and any obligations on the part of AREVA including
settlements of warranties, result solely from the applicable purchase contract, which is not affected by the
contents of the technical manual.

This device MUST NOT be modified. If any modification is made without the express permission of
AREVA, it will invalidate the warranty, and may render the product unsafe.

The AREVA logo and any alternative version thereof are trademarks and service marks of AREVA.

MiCOM is a registered trademark of AREVA. All trade names or trademarks mentioned herein whether registered or not,
are the property of their owners.

This manual is provided for informational use only and is subject to change without notice.

© 2005, AREVA. All rights reserved.

PICS & MICS P44x/EN PM/A11

MiCOM P442 & P444 (PM) 1

CONTENTS

1. PROTOCOL IMPLEMENTATION CONFORMANCE STATEMENT (PICS).........3

1.1 INTRODUCTION ..................................................................................................3

1.2 ACSI BASIC CONFORMANCE STATEMENT .............................................................3

1.3 ACSI MODELS CONFORMANCE STATEMENT .........................................................4

1.4 ACSI SERVICE CONFORMANCE STATEMENT .........................................................5

2. MODEL IMPLEMENTATION CONFORMANCE STATEMENT (MICS)................9

2.1 INTRODUCTION ..................................................................................................9

2.2 OBJECTIVE ........................................................................................................9

2.3 LOGICAL DEVICE DEFINITIONS.............................................................................9

2.4 LOGICAL NODE DEFINITIONS .............................................................................12

2.5 COMMON DATA CLASS DEFINITIONS ..................................................................24

2.6 COMMON DATA ATTRIBUTE TYPE DEFINITIONS ....................................................34

2.7 ENUMERATED TYPE DEFINITIONS .......................................................................35

2.8 MMS DATA-TYPE CONVERSIONS.......................................................................38

P44x/EN PM/A11 PICS & MICS

(PM) 2 MiCOM P442 & P444

PICS & MICS P44x/EN PM/A11

MiCOM P442 & P444 (PM) 3

1. PROTOCOL IMPLEMENTATION CONFORMANCE STATEMENT (PICS)

1.1 Introduction
This specification is the Protocol Implementation Conformance Statement (PICS) and
presents the ACSI conformance statements as defined in Annex A of Part 7-2 of the
IEC61850 standard specifications.
1.2 ACSI basic conformance statement
The basic conformance statement shall be as defined in Table A.1.
Table A.1 - Basic conformance statement

Client/ Server/ Value/

Subscriber Publisher Comments

Client-Server Roles

B11 Server side ⎯ ⎯ c1 Y

(of TWO-PARTY-APPLICATION-ASSOCIATION)
B12 Client side c1 N ⎯ ⎯
(of TWO-PARTY-APPLICATION-ASSOCIATION)

SCSMs Supported

B21 SCSM: IEC 61850-8-1 used N Y

B22 SCSM: IEC 61850-9-1 used
B23 SCSM: IEC 61850-9-2 used
B24 SCSM: Other

Generic Substation Event Model (GSE)

B31 Publisher side ⎯ ⎯ O Y

B32 Subscriber side O Y ⎯ ⎯

Transmission of Sampled Value Model (SVC)

B41 Publisher side ⎯ ⎯ O N

B42 Subscriber side O N ⎯ ⎯
c1 - Shall be ‘M’ if support for LOGICAL-DEVICE model has been declared
O - Optional
M - Mandatory
Y - Yes (supported)
N - No (not supported)
P44x/EN PM/A11 PICS & MICS

(PM) 4 MiCOM P442 & P444

1.3 ACSI models conformance statement

The ACSI models conformance statement shall be as defined in Table A.2.
Table A.2 - ACSI models conformance statement

Client/ Server/ Value/

Subscriber Publisher Comments

If Server Side (B1) Supported

M1 Logical device c2 Y c2 Y
M2 Logical node c3 Y c3 Y
M3 Data c4 Y c4 Y
M4 Data set c5 Y c5 Y
M5 Substitution O N O N
M6 Setting group control O N O N
Reporting
M7 Buffered report control O N O N
M7-1 sequence-number
M7-2 report-time-stamp
M7-3 reason-for-inclusion
M7-4 data-set-name
M7-5 data-reference
M7-6 buffer-overflow
M7-7 entryID
M7-8 BufTim
M7-9 IntgPd
M7-10 GI
M8 Unbuffered report control O N O Y
M8-1 sequence-number N Y
M8-2 report-time-stamp N Y
M8-3 reason-for-inclusion N Y
M8-4 data-set-name N Y
M8-5 data-reference N Y
M8-6 BufTim N Y
M8-7 IntgPd N Y
M8-8 GI N Y
Logging O N O N
M9 Log control O N O N
M9-1 IntgPd N N
M10 Log O N O N
M11 Control M N M N

If GSE (B31/32) is Supported

GOOSE O N O Y
M12-1 entryID ?
M12-2 dataRefInc ?
PICS & MICS P44x/EN PM/A11

MiCOM P442 & P444 (PM) 5

Client/ Server/ Value/

Subscriber Publisher Comments
M13 GSSE O N O N

If SVC (41/42) is Supported

M14 Multicast SVC O O

M15 Unicast SVC O O
M16 Time M M Time source
with required
accuracy shall
be available
M17 File Transfer O O
c2 - Shall be ‘M’ if support for LOGICAL-NODE model has been declared
c3 - Shall be ‘M’ if support for DATA model has been declared
c4 - Shall be ‘M’ if support for DATA-SET, Substitution, Report, Log Control, or Time model has been
declared
c5 - Shall be ‘M’ if support for Report, GSE, or SMV models has been declared

1.4 ACSI service conformance statement

The ACSI service conformance statement shall be as defined in Table A.3 (depending on the
statements in Table A.1).
Table A.3 - ACSI service conformance statement

AA: Client/ Server/

Services Comments
TP/MC Subscriber Publisher
Server (clause 6)
S1 ServerDirectory TP N M Y

Application association (clause 7)

S2 Associate M N M Y
S3 Abort M N M Y
S4 Release M N M Y

Logical device (clause 8)

S5 LogicalDeviceDirectory TP M N M Y

Logical node (clause 9)

S6 LogicalNodeDirectory TP M N M Y
S7 GetAllDataValues TP O N M Y

Data (clause 10)

S8 GetDataValues TP M N M Y
S9 SetDataValues TP O N O N
S10 GetDataDirectory TP O N M Y?
S11 GetDataDefinition TP O N M Y?
P44x/EN PM/A11 PICS & MICS

(PM) 6 MiCOM P442 & P444

AA: Client/ Server/

Services Comments
TP/MC Subscriber Publisher
Data set (clause 11)
S12 GetDataSetValues TP O N M Y?
S13 SetDataSetValues TP O N O N
S14 CreateDataSet TP O N O N
S15 DeleteDataSet TP O N O N
S16 GetDataSetDirectory TP O N O Y?

Substitution (clause 12)

S17 SetDataValues TP M N M N

Setting group control (clause 13)

S18 SelectActiveSG TP O N O N
S19 SelectEditSG TP O N O N
S20 SetSGValues TP O N O N
S21 ConfirmEditSGValues TP O N O N
S22 GetSGValues TP O N O N
S23 GetSGCBValues TP O N O N

Reporting (clause 14)

Buffered report control block (BRCB)
S24 Report TP c6 N c6 N
S24-1 data-change (dchg)
S24-2 qchg-change (qchg)
S24-3 data-update (dupd)
S25 GetBRCBValues TP c6 N c6 N
S26 SetBRCBValues TP c6 N c6 N
Unbuffered report control block (URCB)
S27 Report TP c6 N c6 Y
S27-1 data-change (dchg) N Y
S27-2 qchg-change (qchg) N N
S27-3 data-update (dup N N
S28 GetURCBValues TP c6 N c6 Y
S29 SetURCBValues TP c6 N c6 Y
c6 - Shall declare support for at least one (BRCB or URCB)

Logging (clause 14)

Log control block
S30 GetLCBValues TP M N M N
S31 SetLCBValues TP O N M N
Log
S32 QueryLogByTime TP c7 N M N
S33 QueryLogAfter TP c7 N M N
PICS & MICS P44x/EN PM/A11

MiCOM P442 & P444 (PM) 7

AA: Client/ Server/

Services Comments
TP/MC Subscriber Publisher
S34 GetLogStatusValues TP M N M N
c7 - Shall declare support for at least one (QueryLogByTime or QueryLogByEntry)

Generic substation event model (GSE) (clause 14.3.5.3.4)

GOOSE-CONTROL-BLOCK
S35 SendGOOSEMessage MC c8 N c8 Y
S36 GetGoReference TP O N c9 Y
S37 GetGOOSEElementNumber TP O N c9 Y
S38 GetGoCBValues TP O N O N
S39 SetGoCBValues TP O N O N
GSSE-CONTROL-BLOCK
S40 SendGSSEMessage MC c8 N c8 N
S41 GetGsReference TP O N c9 N
S42 GetGSSEElementNumber TP O N c9 N
S43 GetGsCBValues TP O N O N
S44 SetGsCBValues TP O N O N
c8 - Shall declare support for at least one (SendGOOSEMessage or SendGSSEMessage)
c9 - Shall declare support if TP association is available

Transmission of sampled value model (SVC) (clause 16)

Multicast SVC
S45 SendMSVMessage MC c10 N c10 N
S46 GetMSVCBValues TP O N O N
S47 SetMSVCBValues TP O N O N
Unicast SVC
S48 SendUSVMessage TP c10 N c10 N
S49 GetUSVCBValues TP O N O N
S50 SetUSVCBValues TP O N O N
c10 - Shall declare support for at least one (SendMSVMessage or SendUSVMessage)

Control (clause 17.5.1)

S51 Select M N O N
S52 SelectWithValue TP M N O N
S53 Cancel TP O N O N
S54 Operate TP M N M N
S55 Command-Termination TP M N O N
S56 TimeActivated-Operate TP O N O N

File transfer (clause 20)

S57 GetFile TP O N M Y
S58 SetFile TP O N O N
S59 DeleteFile TP O N O Y
P44x/EN PM/A11 PICS & MICS

(PM) 8 MiCOM P442 & P444

AA: Client/ Server/

Services Comments
TP/MC Subscriber Publisher
S60 GetFileAttributeValues TP O N M Y

Time (5.5)
T1 Time resolution of internal clock 1ms Nearest
negative power
of 2 in seconds
T2 Time accuracy of internal clock 1ms T0
T1
T2
T3
T4
T5
T3 Supported TimeStamp resolution 1ms Nearest value
of 2**-n in
seconds
according to
5.5.3.7.3.3
PICS & MICS P44x/EN PM/A11

MiCOM P442 & P444 (PM) 9

2. MODEL IMPLEMENTATION CONFORMANCE STATEMENT (MICS)

2.1 Introduction
This specification is the Model Implementation Conformance Statement (MICS) and presents
the top-level IEC61850 data model that has been implemented. The definitions of all used
Logical Nodes and their associated Common Data Classes, components and associated
enumerated values are also included for completeness.
The reader is expected to be conversant with the terminology presented within the IEC61850
part 7 series of specifications.

2.2 Objective
To provide comprehensive details of the standard data object model elements supported by
the device. The MICS is conformant to the devices associated ICD (Substation Configuration
Language) file, according to part 6 of the IEC61850 standards. The layout of the presented
tables within this document are conformant to the part 7 series of the IEC61850 standard
specifications with the following exceptions:

• The "Trigger Options" field is not presented.

• The "M/O" field is not present as the definitions are as deployed within the model.

• An additional column "X" is used to signify AREVA custom attributes.

2.3 Logical Device definitions

The MiCOM relay implements an IEC61850 server that can contain one or more Logical
Devices. Each Logical Device contains a data model built from instances of specific Logical
Nodes and must consist of at least an instance of the LPHD Logical Node (which is
responsible for providing physical device information) and an instance of the LLN0 Logical
Node (for addressing common issues across the Logical Device).
The IEC61850 data model is contained within the Logical Devices detailed in the table
below. All MiCOM devices will name the supported Logical Devices consistently to ensure
that data model variables with the same purpose will have the same name within each
MiCOM server.

Logical Device Comment / Usage

Control P444/P442 Controls Domain
Measurements P444/P442 Measurements Domain
Protection P444/P442 Protection Domain
Records P444/P442 Records Domain
System P444/P442 System Domain

2.3.1 IEC61850 Logical Device data model

The IEC61850 Logical Device top-level data model consists of instances of Logical Nodes.
The data model name for a Logical Node instance is constructed from an optional prefix
(known as the wrapper), the Logical Node name, and an instance ID (or suffix).
The presented data model is in an alphabetically sorted order, rather than a logical order,
because this is the natural order of the data when presented by a native MMS browser.
(Higher level browsers can of course impart any ordering that they desire.)
P44x/EN PM/A11 PICS & MICS

(PM) 10 MiCOM P442 & P444

LD LN Instance LN Type Description

Control

ArcRREC1 RREC_NO_SEG Auto Reclose

AscRSYN1 RSYN_MAN_AUTO System Checks - Check Sync 1
LLN0 LLN0_CONTROL Controls Logical Device
LPHD1 LPHD_STANDARD Physical Device Information
PsbRPSB1 RPSB_BASIC Zone 1 / Zone 1 extented Ph/Gnd Power

Swing Blocking

PsbRPSB2 RPSB_BASIC Zone 2 Ph/Gnd Power Swing Blocking

PsbRPSB3 RPSB_BASIC Zone 3 Ph/Gnd Power Swing Blocking
PsbRPSB4 RPSB_BASIC Zone 4 Ph/Gnd Power Swing Blocking
PsbRPSB5 RPSB_BASIC Zone P Ph/Gnd Power Swing Blocking
XCBR1 XCBR_BASIC Circuit Breaker Monitoring (Pole 1)
XCBR2 XCBR_BASIC Circuit Breaker Monitoring (Pole 2)
XCBR3 XCBR_BASIC Circuit Breaker Monitoring (Pole 3)

Measurements

FouMMXU1 MMXU_FOURIER_P440 Fourier Measurements

LLN0 LLN0_STANDARD Measurements Logical Device
LPHD1 LPHD_STANDARD Physical Device Information
MSQI1 MSQI_P440 Sequences Measurement
MSTA1 MSTA_W_VAR Metering Statistics

Protection

CbfRBRF1 RBRF_EXTTRIP CB Fail 1

CbfRBRF2 RBRF_EXTTRIP CB Fail 2
DisPDIS1 PDIS_PG Distance Protection Zone 1
DisPDIS2 PDIS_PG Distance Protection Zone 2
DisPDIS3 PDIS_PG Distance Protection Zone 3
DisPDIS4 PDIS_PG Distance Protection Zone 4
DisPDIS5 PDIS_PG Distance Protection Programmable Zone P
DisPDIS6 PDIS_PG Distance Protection Extended Zone 1x
DisPSCH1 PSCH_DIS Distance scheme
EfaPSCH1 PSCH_DEF Directionnal Earth Fault Aided Scheme
EfaPTOC1 PTOC_SEG Earth Fault Aided
EfdPDOP1 PDOP_BASIC Zero Sequence Overpower
EfdPTOC1 PTOC_NEU IN> 1 Earth Fault (Derived)
EfdPTOC2 PTOC_NEU IN> 2 Earth Fault (Derived)
EfdPTOC3 PTOC_NEU IN> 3 Earth Fault (Derived)
EfdPTOC4 PTOC_NEU IN> 4 Earth Fault (Derived)
LLN0 LLN0_PROT Protection Logical Device
LPHD1 LPHD_STANDARD Physical Device Information
PICS & MICS P44x/EN PM/A11

MiCOM P442 & P444 (PM) 11

LD LN Instance LN Type Description

NgcPTOC1 PTOC_NO_SEG Negative Sequence Overcurrent
OcpPTOC1 PTOC_NO_SEG I> 1 Overcurrent
OcpPTOC2 PTOC_NO_SEG I> 2 Overcurrent
OcpPTOC3 PTOC_NO_SEG I> 3 Overcurrent
OcpPTOC4 PTOC_NO_SEG I> 4 Overcurrent
PTRC1 PTRC_NO_SEG Protection Trip Conditioning
SofPSOF1 PSOF_BASIC Switch onto Fault protection
ThmPTTR1 PTTR_NO_SEG Thermal Overload
TorPSOF1 PSOF_BASIC Trip on reclose protection
VtpPhsPTOV1 PTOV_NO_SEG V> 1 Overvoltage
VtpPhsPTOV2 PTOV_NO_SEG V> 2 Overvoltage
VtpPhsPTUV1 PTUV_NO_SEG V< 1 Undervoltage
VtpPhsPTUV2 PTUV_NO_SEG V< 2 Undervoltage

Records

LLN0 LLN0_STANDARD Disturbance Record Logical Device

LPHD1 LPHD_STANDARD Physical Device Information
RDRE1 RDRE_BASIC Disturbance Recorder
RFLO1 RFLO_BASIC Fault Locator

System

AlmGGIO1 GGIO_ALM_96 Alarms

GosGGIO1 GGIO_IND_32 GOOSE Input Signals
GosGGIO2 GGIO_IND_32 GOOSE Output Signals
LedGGIO1 GGIO_IND_8 Red LED Signals
LLN0 LLN0_STANDARD System Logical Device
LPHD1 LPHD_STANDARD Physical Device Information
OptGGIO1 GGIO_IND_24 Optos Inputs
PloGGIO1 GGIO_IND_32 Controls
RlyGGIO1 GGIO_IND_46 Output Contacts
P44x/EN PM/A11 PICS & MICS

(PM) 12 MiCOM P442 & P444

2.4 Logical Node definitions

The definition tables for each of the Logical Nodes in the top-level data model are presented
in the following sub-sections.
The following table presents a summary of the Logical Node templates used across the
Logical Devices within the overall IEC61850 product data model:
LN Type (LN Description Name Space
Generic Process I/O
GGIO_IND_24 (GGIO) AREVA-SII:PCS-Px40
(w.r.t 24 Indication Elements)
Generic Process I/O
GGIO_IND_32 (GGIO) AREVA-SII:PCS-Px40
(w.r.t 32 Indication Elements)
Generic Process I/O
GGIO_IND_46 (GGIO) AREVA-SII:PCS-Px40
(w.r.t 46 Indication Elements)
Generic Process I/O
GGIO_IND_8 (GGIO) AREVA-SII:PCS-Px40
(w.r.t 8 Indication Elements)
Generic Process I/O
GGIO_ALM_96 (GGIO) AREVA-SII:PCS-Px40
(w.r.t 96 Alarm Elements)
LLN0_CONTROL (LLN0) Control Domain Logical Node 0 AREVA-SII:PCS-Px40
LLN0_PROT (LLN0) Protection Domain Logical Node 0 AREVA-SII:PCS-Px40
LLN0_STANDARD (LLN0) General Logical Node 0 IEC61850-7-4:2003
LPHD_STANDARD (LPHD) Px40 Physical Device Information IEC61850-7-4:2003
Standard measurements (w.r.t Fourier
MMXU_FOURIER_P440 (MMXU) IEC61850-7-4:2003
Values - P440)
Sequence and imbalance ( Magnitude
MSQI_P440 (MSQI) IEC61850-7-4:2003
Pos,Neg,Zero)
Metering Statistics (w.r.t Real + Reactive
MSTA_W_VAR (MSTA) AREVA-SII:PCS-Px40
Power - Average + Max values)
PDIS_PG (PDIS) Distance Zone Phase and Ground IEC61850-7-4:2003
Directionnal Overpower ( w.r.t Mandatory
PDOP_BASIC (PDOP) IEC61850-7-4:2003
only)
PSCH_DIS (PSCH) Protection Scheme for distance IEC61850-7-4:2003
Protection Scheme for Aided Directionnal
PSCH_DEF (PSCH) IEC61850-7-4:2003
Earth Fault
PSOF_BASIC (PSOF) Switch-onto-Fault Protection AREVA-SII:PCS-Px40
PTOC_NEU (PTOC) Timed Overcurrent (w.r.t Neutral) IEC61850-7-4:2003
Timed Overcurrent (w.r.t No Phase
PTOC_NO_SEG (PTOC) IEC61850-7-4:2003
Segregation)
Timed Overcurrent (w.r.t Phase
PTOC_SEG (PTOC) IEC61850-7-4:2003
Segregation)
PTOV_NO_SEG (PTOV) Overvoltage (w.r.t Phase Segregation) IEC61850-7-4:2003
Protection trip conditioning (w.r.t No Phase
PTRC_NO_SEG (PTRC) IEC61850-7-4:2003
Segregation)
Thermal overload (w.r.t No Phase
PTTR_NO_SEG (PTTR) IEC61850-7-4:2003
Segregation)
PTUV_NO_SEG (PTUV) Undervoltage (w.r.t No Phase Segregation) IEC61850-7-4:2003
RBRF_EXTTRIP (RBRF) Breaker Failure (w.r.t External Tripping) IEC61850-7-4:2003
Disturbance Recorder function (w.r.t
RDRE_BASIC (RDRE) IEC61850-7-4:2003
Mandatory Attributes only)
Fault locator (w.r.t Mandatory Attributes
RFLO_BASIC (RFLO) IEC61850-7-4:2003
only)
Power swing detection/blocking (w.r.t
RPSB_BASIC (RPSB) IEC61850-7-4:2003
Mandatory Attributes only)
RREC_NO_SEG (RREC) Autoreclosing (w.r.t No Phase Segregation) IEC61850-7-4:2003
Synchronism-check / Synchronising (w.r.t
RSYN_MAN_AUTO (RSYN) IEC61850-7-4:2003
Calculated for Manual and automatic close)
Circuit Breaker (w.r.t Mandatory Attributes
XCBR_BASIC (XCBR) IEC61850-7-4:2003
Only)
PICS & MICS P44x/EN PM/A11

MiCOM P442 & P444 (PM) 13

2.4.1 Logical Node: GGIO_ALM_96

Description: Generic Process I/O (w.r.t 96 Alarm Elements)

LN Class: GGIO

Attribute Attr. Type Explanation T X

Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN_PRIV Name Plate
Alm1 SPS_D General single alarm
Alm2 SPS_D General single alarm
Alm3 SPS_D General single alarm
Alm4 SPS_D General single alarm
Alm5 SPS_D General single alarm
Alm6 SPS_D General single alarm
Alm7 SPS_D General single alarm
Alm8 SPS_D General single alarm
Alm9 SPS_D General single alarm
Alm10 SPS_D General single alarm
Alm11 SPS_D General single alarm
Alm12 SPS_D General single alarm
Alm13 SPS_D General single alarm
Alm14 SPS_D General single alarm
Alm15 SPS_D General single alarm
Alm16 SPS_D General single alarm
Alm17 SPS_D General single alarm
Alm18 SPS_D General single alarm
Alm19 SPS_D General single alarm
Alm20 SPS_D General single alarm
Alm21 SPS_D General single alarm
Alm22 SPS_D General single alarm
Alm23 SPS_D General single alarm
Alm24 SPS_D General single alarm
Alm25 SPS_D General single alarm
Alm26 SPS_D General single alarm
Alm27 SPS_D General single alarm
Alm28 SPS_D General single alarm
Alm29 SPS_D General single alarm
Alm30 SPS_D General single alarm
Alm31 SPS_D General single alarm
Alm32 SPS_D General single alarm
Alm33 SPS_D General single alarm
Alm34 SPS_D General single alarm
Alm35 SPS_D General single alarm
Alm36 SPS_D General single alarm
Alm37 SPS_D General single alarm
Alm38 SPS_D General single alarm
Alm39 SPS_D General single alarm
Alm40 SPS_D General single alarm
Alm41 SPS_D General single alarm
Alm42 SPS_D General single alarm
Alm43 SPS_D General single alarm
Alm44 SPS_D General single alarm
Alm45 SPS_D General single alarm
Alm46 SPS_D General single alarm
Alm47 SPS_D General single alarm
Alm48 SPS_D General single alarm
Alm49 SPS_D General single alarm
Alm50 SPS_D General single alarm
P44x/EN PM/A11 PICS & MICS

(PM) 14 MiCOM P442 & P444

Attribute Attr. Type Explanation T X

Alm51 SPS_D General single alarm
Alm52 SPS_D General single alarm
Alm53 SPS_D General single alarm
Alm54 SPS_D General single alarm
Alm55 SPS_D General single alarm
Alm56 SPS_D General single alarm
Alm57 SPS_D General single alarm
Alm58 SPS_D General single alarm
Alm59 SPS_D General single alarm
Alm60 SPS_D General single alarm
Alm61 SPS_D General single alarm
Alm62 SPS_D General single alarm
Alm63 SPS_D General single alarm
Alm64 SPS_D General single alarm
Alm65 SPS_D General single alarm
Alm66 SPS_D General single alarm
Alm67 SPS_D General single alarm
Alm68 SPS_D General single alarm
Alm69 SPS_D General single alarm
Alm70 SPS_D General single alarm
Alm71 SPS_D General single alarm
Alm72 SPS_D General single alarm
Alm73 SPS_D General single alarm
Alm74 SPS_D General single alarm
Alm75 SPS_D General single alarm
Alm76 SPS_D General single alarm
Alm77 SPS_D General single alarm
Alm78 SPS_D General single alarm
Alm79 SPS_D General single alarm
Alm80 SPS_D General single alarm
Alm81 SPS_D General single alarm
Alm82 SPS_D General single alarm
Alm83 SPS_D General single alarm
Alm84 SPS_D General single alarm
Alm85 SPS_D General single alarm
Alm86 SPS_D General single alarm
Alm87 SPS_D General single alarm
Alm88 SPS_D General single alarm
Alm89 SPS_D General single alarm
Alm90 SPS_D General single alarm
Alm91 SPS_D General single alarm
Alm92 SPS_D General single alarm
Alm93 SPS_D General single alarm
Alm94 SPS_D General single alarm
Alm95 SPS_D General single alarm
Alm96 SPS_D General single alarm

2.4.2 Logical Node: GGIO_IND_24

Description: Generic Process I/O (w.r.t 24 Indication Elements)

LN Class: GGIO

Attribute Attr. Type Explanation T X

Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN_PRIV Name Plate
Ind1 SPS_D General indication (binary input)
Ind2 SPS_D General indication (binary input)
Ind3 SPS_D General indication (binary input)
Ind4 SPS_D General indication (binary input)
Ind5 SPS_D General indication (binary input)
PICS & MICS P44x/EN PM/A11

MiCOM P442 & P444 (PM) 15

Ind6 SPS_D General indication (binary input)

Ind7 SPS_D General indication (binary input)
Ind8 SPS_D General indication (binary input)
Ind9 SPS_D General indication (binary input)
Ind10 SPS_D General indication (binary input)
Ind11 SPS_D General indication (binary input)
Ind12 SPS_D General indication (binary input)
Ind13 SPS_D General indication (binary input)
Ind14 SPS_D General indication (binary input)
Ind15 SPS_D General indication (binary input)
Ind16 SPS_D General indication (binary input)
Ind17 SPS_D General indication (binary input)
Ind18 SPS_D General indication (binary input)
Ind19 SPS_D General indication (binary input)
Ind20 SPS_D General indication (binary input)
Ind21 SPS_D General indication (binary input)
Ind22 SPS_D General indication (binary input)
Ind23 SPS_D General indication (binary input)
Ind24 SPS_D General indication (binary input)

2.4.3 Logical Node: GGIO_IND_32

Description: Generic Process I/O (w.r.t 32 Indication Elements)

LN Class: GGIO
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN_PRIV Name Plate
Ind1 SPS_D General indication (binary input)
Ind2 SPS_D General indication (binary input)
Ind3 SPS_D General indication (binary input)
Ind4 SPS_D General indication (binary input)
Ind5 SPS_D General indication (binary input)
Ind6 SPS_D General indication (binary input)
Ind7 SPS_D General indication (binary input)
Ind8 SPS_D General indication (binary input)
Ind9 SPS_D General indication (binary input)
Ind10 SPS_D General indication (binary input)
Ind11 SPS_D General indication (binary input)
Ind12 SPS_D General indication (binary input)
Ind13 SPS_D General indication (binary input)
Ind14 SPS_D General indication (binary input)
Ind15 SPS_D General indication (binary input)
Ind16 SPS_D General indication (binary input)
Ind17 SPS_D General indication (binary input)
Ind18 SPS_D General indication (binary input)
Ind19 SPS_D General indication (binary input)
Ind20 SPS_D General indication (binary input)
Ind21 SPS_D General indication (binary input)
Ind22 SPS_D General indication (binary input)
Ind23 SPS_D General indication (binary input)
Ind24 SPS_D General indication (binary input)
Ind25 SPS_D General indication (binary input)
Ind26 SPS_D General indication (binary input)
Ind27 SPS_D General indication (binary input)
Ind28 SPS_D General indication (binary input)
Ind29 SPS_D General indication (binary input)
Ind30 SPS_D General indication (binary input)
Ind31 SPS_D General indication (binary input)
Ind32 SPS_D General indication (binary input)

2.4.4 Logical Node: GGIO_IND_46

P44x/EN PM/A11 PICS & MICS

(PM) 16 MiCOM P442 & P444

Description: Generic Process I/O (w.r.t 46 Indication Elements)

LN Class: GGIO
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN_PRIV Name Plate
Ind1 SPS_D General indication (binary input)
Ind2 SPS_D General indication (binary input)
Ind3 SPS_D General indication (binary input)
Ind4 SPS_D General indication (binary input)
Ind5 SPS_D General indication (binary input)
Ind6 SPS_D General indication (binary input)
Ind7 SPS_D General indication (binary input)
Ind8 SPS_D General indication (binary input)
Ind9 SPS_D General indication (binary input)
Ind10 SPS_D General indication (binary input)
Ind11 SPS_D General indication (binary input)
Ind12 SPS_D General indication (binary input)
Ind13 SPS_D General indication (binary input)
Ind14 SPS_D General indication (binary input)
Ind15 SPS_D General indication (binary input)
Ind16 SPS_D General indication (binary input)
Ind17 SPS_D General indication (binary input)
Ind18 SPS_D General indication (binary input)
Ind19 SPS_D General indication (binary input)
Ind20 SPS_D General indication (binary input)
Ind21 SPS_D General indication (binary input)
Ind22 SPS_D General indication (binary input)
Ind23 SPS_D General indication (binary input)
Ind24 SPS_D General indication (binary input)
Ind25 SPS_D General indication (binary input)
Ind26 SPS_D General indication (binary input)
Ind27 SPS_D General indication (binary input)
Ind28 SPS_D General indication (binary input)
Ind29 SPS_D General indication (binary input)
Ind30 SPS_D General indication (binary input)
Ind31 SPS_D General indication (binary input)
Ind32 SPS_D General indication (binary input)
Ind33 SPS_D General indication (binary input)
Ind34 SPS_D General indication (binary input)
Ind35 SPS_D General indication (binary input)
Ind36 SPS_D General indication (binary input)
Ind37 SPS_D General indication (binary input)
Ind38 SPS_D General indication (binary input)
Ind39 SPS_D General indication (binary input)
Ind40 SPS_D General indication (binary input)
Ind41 SPS_D General indication (binary input)
Ind42 SPS_D General indication (binary input)
Ind43 SPS_D General indication (binary input)
Ind44 SPS_D General indication (binary input)
Ind45 SPS_D General indication (binary input)
Ind46 SPS_D General indication (binary input)
PICS & MICS P44x/EN PM/A11

MiCOM P442 & P444 (PM) 17

2.4.5 Logical Node: GGIO_IND_8

Description: Generic Process I/O (w.r.t 8 Indication Elements)

LN Class: GGIO
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN_PRIV Name Plate
Ind1 SPS_D General indication (binary input)
Ind2 SPS_D General indication (binary input)
Ind3 SPS_D General indication (binary input)
Ind4 SPS_D General indication (binary input)
Ind5 SPS_D General indication (binary input)
Ind6 SPS_D General indication (binary input)
Ind7 SPS_D General indication (binary input)
Ind8 SPS_D General indication (binary input)

2.4.6 Logical Node: LLN0_CONTROL

Description: Control Domain Logical Node 0

LN Class: LLN0
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LLNO_LNPRIV Name Plate
AscMod INC_MOD_D Check Synchronisation
AscBeh INS_BEH_D Check Synchronisation
ArcMod INC_MOD_D Auto-Reclose
ArcBeh INS_BEH_D Auto-Reclose
PsbBeh INS_BEH_D Power Swing Blocking
PsbMod INC_MOD_D Power Swing Blocking

2.4.7 Logical Node: LLN0_PROT1

Description: Protection Domain Logical Node 0

LN Class: LLN0
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LLNO_LNPRIV Name Plate
OcpMod INC_MOD_D Overcurrent Mode
OcpBeh INS_BEH_D Overcurrent Behaviour
NgcMod INC_MOD_D Negative Sequence Mode
NgcBeh INS_BEH_D Negative Sequence Behaviour
EfdMod INC_MOD_D Earth Fault (Derived) Mode
EfdBeh INS_BEH_D Earth Fault (Derived) Behaviour
EfaMod INC_MOD_D Earth Fault Aided (Derived) Mode
EfaBeh INS_BEH_D Earth Fault Aided (Derived)
Behaviour
VtpMod INC_MOD_D Overvoltage/Undervoltage Mode
VtpBeh INS_BEH_D Overvoltage/Undervoltage
Behaviour
DisBeh INS_BEH_D Distance Behaviour
DisMod INC_MOD_D Distance Mode
ThmMod INC_MOD_D Thermal Overload Mode
ThmBeh INS_BEH_D Thermal Overload Behaviour
CbfMod INC_MOD_D CB Fail Mode
CbfBeh INS_BEH_D CB Fail Behaviour
P44x/EN PM/A11 PICS & MICS

(PM) 18 MiCOM P442 & P444

2.4.8 Logical Node: LLN0_STANDARD

Description: General Logical Node 0

LN Class: LLN0
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LLN0 Name Plate

2.4.9 Logical Node: LPHD_STANDARD

Description: Px40 Physical Device Information

LN Class: LPHD
Attribute Attr. Type Explanation T X
PhyNam DPL_STANDARD Physical device name plate
PhyHealth INS_HEALTH Physical device health
Proxy SPS_D Indicates if this LN is a proxy
PwrUp SPS_D Power up detected

2.4.10 Logical Node: MMXU_FOURIER_P440

Description: Standard measurements (w.r.t Fourier Values - P440)

LN Class: MMXU
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN_PRIV Name Plate
TotW MV_FLOAT Total active power (Total P)
TotVAr MV_FLOAT Total reactive power (Total Q)
TotVA MV_FLOAT Total apparent power (Total S)
TotPF MV_FLOAT Average power factor (Total PF)
Hz MV_FLOAT Frequency
PPV DEL_SEG_ANG Phase to Phase voltages
PhV WYE_SEG_RES_D Phase to Ground voltages
A WYE_SEG_RES_D Phase currents
W WYE_SEG Phase active power (P)
VAr WYE_SEG Phase reactive power (Q)
VA WYE_SEG Phase apparent power (S)
PF WYE_SEG Phase power factor

2.4.11 Logical Node: MSQI_P440

Description: Sequence and imbalance ( Magnitude Pos,Neg,Zero)

LN Class: MSQI
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN Name Plate
SeqA SEQ_MAG Positive, Negative and Zero
sequence current
SeqV SEQ_MAG Positive, Negative and Zero
sequence voltage
ImbA WYE_RES_ANG_D Imbalance current
PICS & MICS P44x/EN PM/A11

MiCOM P442 & P444 (PM) 19

2.4.12 Logical Node: MSTA_W_VAR

Description: Metering Statistics (w.r.t Real + Reactive Power - Average + Max values)
LN Class: MSTA
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN_PRIV Name Plate
AvW MV_FLOAT_D Average real power
MaxW MV_FLOAT_D Maximum real power
AvVAr MV_FLOAT_D Average reactive power
MaxVAr MV_FLOAT_D Maximum reactive power

2.4.13 Logical Node: PDIS_PG

Description: Distance Zone Phase and Ground

LN Class: PDIS
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN Name Plate
Op ACT_SEG_NEU Operate T
Str ACD_SEG_NEU Start

2.4.14 Logical Node: PDOP_BASIC

Description: Directionnal Overpower ( w.r.t Mandatory only)

LN Class: PDOP
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN Name Plate
Str ACD_NEU Start
Op ACT_NEU Operate T

2.4.15 Logical Node: PSCH_DEF

Description: Protection Scheme for Aided Directionnal Earth Fault

LN Class: PSCH
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN Name Plate
ProTx SPS_WD Teleprotection signal transmitted T
ProRx SPS_WD Teleprotection signal received T
Str ACD_NO_SEG carrier send
Op ACT_SEG Operate T
CarRx ACT_NO_SEG Carrier received after unblock logic
LosOfGrd SPS_WD Loss of guard
P44x/EN PM/A11 PICS & MICS

(PM) 20 MiCOM P442 & P444

2.4.16 Logical Node: PSCH_DIS

Description: Protection Scheme for distance

LN Class: PSCH
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN Name Plate
ProTx SPS_WD Teleprotection signal transmitted T
ProRx SPS_WD Teleprotection signal received T
Str ACD_NO_SEG carrier send
Op ACT_SEG_NEU Operate T
CarRx ACT_NO_SEG Carrier received after unblock logic
LosOfGrd SPS_WD Loss of guard
WeiOp ACT_SEG Operate signal from weak infeed
function

2.4.17 Logical Node: PSOF_BASIC

Description: Switch-onto-Fault Protection

LN Class: PSOF
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN Name Plate
Str ACD_NO_SEG Start T
Op ACT_NO_SEG Operate

2.4.18 Logical Node: PTOC_NEU

Description: Timed Overcurrent (w.r.t Neutral)

LN Class: PTOC
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN Name Plate
Str ACD_NEU Start
Op ACT_NEU Operate T

2.4.19 Logical Node: PTOC_NO_SEG

Description: Timed Overcurrent (w.r.t No Phase Segregation)

LN Class: PTOC
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN Name Plate
Str ACD_NO_SEG Start
Op ACT_NO_SEG Operate T
PICS & MICS P44x/EN PM/A11

MiCOM P442 & P444 (PM) 21

2.4.20 Logical Node: PTOC_SEG

Description: Timed Overcurrent (w.r.t Phase Segregation)

LN Class: PTOC
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN Name Plate
Str ACD_SEG Start
Op ACT_SEG Operate T

2.4.21 Logical Node: PTOV_NO_SEG

Description: Overvoltage (w.r.t Phase Segregation)

LN Class: PTOV
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN Name Plate
Str ACD_NO_SEG Start
Op ACT_NO_SEG Operate T

2.4.22 Logical Node: PTRC_NO_SEG

Description: Protection trip conditioning (w.r.t No Phase Segregation)

LN Class: PTRC
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN Name Plate
Tr ACT_NO_SEG Trip
Str ACD_NO_SEG Sum of all starts of all connected
Logical Nodes

2.4.23 Logical Node: PTTR_NO_SEG

Description: Thermal overload (w.r.t No Phase Segregation)

LN Class: PTTR
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN Name Plate
TmpRl MV_FLOAT Relation between temperature and
maximum temperature
Op ACT_NO_SEG Operate T
AlmThm ACT_NO_SEG Thermal alarm T
P44x/EN PM/A11 PICS & MICS

(PM) 22 MiCOM P442 & P444

2.4.24 Logical Node: PTUV_NO_SEG

Description: Undervoltage (w.r.t No Phase Segregation)

LN Class: PTUV
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN Name Plate
Str ACD_NO_SEG Start
Op ACT_NO_SEG Operate T

2.4.25 Logical Node: RBRF_EXTTRIP

Description: Breaker Failure (w.r.t External Tripping)

LN Class: RBRF
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN Name Plate
OpEx ACT_NO_SEG Breaker failure trip ("External trip") T

2.4.26 Logical Node: RDRE_BASIC

Description: Disturbance Recorder function (w.r.t Mandatory Attributes only)

LN Class: RDRE
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN Name Plate
RcdMade SPS_WD Recording made
FltNum INS_BASIC Fault number

2.4.27 Logical Node: RFLO_BASIC

Description: Fault locator (w.r.t Mandatory Attributes only)

LN Class: RFLO
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN Name Plate
FltZ CMV_MAG_FLOAT Fault impedance
FltDiskm MV_FLOAT Fault distance in km

2.4.28 Logical Node: RPSB_BASIC

Description: Power swing detection/blocking (w.r.t Mandatory Attributes only)

LN Class: RPSB
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN Name Plate
BlkZn SPS_WD Blocking of correlated PDIS zone
Op ACT_NO_SEG Operate ( Out of step Tripping) T
Str ACD_NO_SEG Start (Power Swing Detected)

2.4.29 Logical Node: RREC_NO_SEG

PICS & MICS P44x/EN PM/A11

MiCOM P442 & P444 (PM) 23

Description: Autoreclosing (w.r.t No Phase Segregation)

LN Class: RREC
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN Name Plate
Op ACT_NO_SEG Operate (used here to provide T
close to XCBR)
AutoRecSt INS_AR_STATE Auto reclosing status

2.4.30 Logical Node: RSYN_MAN_AUTO

Description: Synchronism-check / Synchronising (w.r.t Calculated for Manual and automatic close)
LN Class: RSYN
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN Name Plate
Rel SPS_WD Release
DifHzClc MV_FLOAT Calculated difference in frequency

2.4.31 Logical Node: XCBR_BASIC

Description: Circuit Breaker (w.r.t Mandatory Attributes Only)

LN Class: XCBR
Attribute Attr. Type Explanation T X
Mod INC_MOD Mode
Beh INS_BEH Behaviour
Health INS_HEALTH Health
NamPlt LPL_LN Name Plate
Loc SPS_WD Local operation
EEHealth INS_BASIC External equipment health
OpCnt INS_BASIC Operation counter
Pos DPC_STATUS Switch position
BlkOpn SPC_STATUS Block opening
BlkCls SPC_STATUS Block closing
P44x/EN PM/A11 PICS & MICS

(PM) 24 MiCOM P442 & P444

2.5 Common Data Class definitions

The definition tables for each of the Common Data Classes used in the Logical Node
definitions are presented in the following sub-sections.
From an application point-of-view the data attributes of a Common Data Class are classified
according to their specific use. The characterisation of data attributes, and the services that
they support/provide, will be through the use of 'Functional Contraints'. The Functional
Constraints are specified by the table below:

FC Name Semantic Source Definition

BR Buffered reports IEC61850-7-2
CF Configuration IEC61850-7-2
CO Control IEC61850-7-2
DC Description IEC61850-7-2
EX Extended Definition IEC61850-7-2
GO GOOSE Control IEC61850-7-2
GS GSSE Control (UCA2 GOOSE) IEC61850-7-2
LG Logging IEC61850-7-2
MS Multicast sampled value control IEC61850-7-2
MX Measurands (Analogue values) IEC61850-7-2
RP Unbuffered reports IEC61850-7-2
SE Setting Group Editable IEC61850-7-2
SG Setting Group IEC61850-7-2
SP Set Point IEC61850-7-2
ST Status Information IEC61850-7-2
SV Substitution Values IEC61850-7-2
US Unicast sampled value control IEC61850-7-2
XX Data attribute service parameters IEC61850-7-2

2.5.1 Common Data Class: ACD_NEU

Description: Directional Protection Activation Information (w.r.t Neutral)

CDC Class: ACD

Attribute Type FC Enumeration Comment X

general BOOLEAN ST Trip or start has happened

ENUMERATED8 General direction (unknown,

dirGeneral ST enumDirectionGeneral
MMS Type: INT8 forward, backward or both)
Trip or start event with earth
neut BOOLEAN ST
current has happened
Earth current direction
ENUMERATED8
dirNeut ST enumDirectionPhase (unknown, forward or
MMS Type: INT8
backward)
Quality of the protection
q Quality ST
activation information
Timestamp of the last
t TimeStamp ST change in state of protection
activation information

2.5.2 Common Data Class: ACD_NO_SEG

Description: Directional Protection Activation Information (w,r,t No Phase Segregation)

CDC Class: ACD
Attribute Type FC Enumeration Comment X
general BOOLEAN ST Trip or start has happened
ENUMERATED8 General direction (unknown,
dirGeneral ST enumDirectionGeneral
MMS Type: INT8 forward, backward or both)
q Quality ST Quality of the protection
PICS & MICS P44x/EN PM/A11

MiCOM P442 & P444 (PM) 25

Attribute Type FC Enumeration Comment X

activation information
Timestamp of the last
t TimeStamp ST change in state of protection
activation information

2.5.3 Common Data Class: ACD_SEG

Description: Directional Protection Activation Information (w.r.t Phase Segregation)

CDC Class: ACD
Attribute Type FC Enumeration Comment X
general BOOLEAN ST Trip or start has happened
General direction
ENUMERATED8
dirGeneral ST enumDirectionGenera (unknown, forward,
MMS Type: INT8
backward or both)
Trip or start event of Phase
phsA BOOLEAN ST
A has happened
Phase A direction
ENUMERATED8
dirPhsA ST enumDirectionPhase (unknown, forward or
MMS Type: INT8
backward)
Trip or start event of Phase
phsB BOOLEAN ST
B has happened
Phase B direction
ENUMERATED8
dirPhsB ST enumDirectionPhase (unknown, forward or
MMS Type: INT8
backward)
Trip or start event of Phase
phsC BOOLEAN ST
C has happened
Phase C direction
ENUMERATED8
dirPhsC ST enumDirectionPhase (unknown, forward or
MMS Type: INT8
backward)
Quality of the protection
q Quality ST
activation information
Timestamp of the last
change in state of
t TimeStamp ST
protection activation
information

2.5.4 Common Data Class: ACD_SEG_NEU

Description: Directional Protection Activation Information (w.r.t Phase Segregation + Neutral)

CDC Class: ACD
Attribute Type FC Enumeration Comment X
general BOOLEAN ST Trip or start has happened
General direction
ENUMERATED8
dirGeneral ST enumDirectionGeneral (unknown, forward,
MMS Type: INT8
backward or both)
Trip or start event of Phase
phsA BOOLEAN ST
A has happened
Phase A direction
ENUMERATED8
dirPhsA ST enumDirectionPhase (unknown, forward or
MMS Type: INT8
backward)
Trip or start event of Phase
phsB BOOLEAN ST
B has happened
Phase B direction
ENUMERATED8
dirPhsB ST enumDirectionPh ase (unknown, forward or
MMS Type: INT8
backward)
Trip or start event of Phase
phsC BOOLEAN ST
C has happened
Phase C direction
ENUMERATED8
dirPhsC ST enumDirectionPhase (unknown, forward or
MMS Type: INT8
backward)
Trip or start event with earth
neut BOOLEAN ST
current has happened
Earth current direction
ENUMERATED8
dirNeut ST enumDirectionPhase (unknown, forward or
MMS Type: INT8
backward)
Quality of the protection
q Quality ST
activation information
P44x/EN PM/A11 PICS & MICS

(PM) 26 MiCOM P442 & P444

Attribute Type FC Enumeration Comment X

Timestamp of the last
change in state of
t TimeStamp ST
protection activation
information

2.5.5 Common Data Class: ACT_NEU

Description: Protection Activation Information (w.r.t Neutral)

CDC Class: ACT
Attribute Type FC Enumeration Comment X
general BOOLEAN ST Trip or start has happened
Trip or start event with
neut BOOLEAN ST earth current has
happened
Quality of the protection
q Quality ST
activation information
Timestamp of the last
change in state of
t TimeStamp ST
protection activation
information

2.5.6 Common Data Class: ACT_NO_SEG

Description: Protection Activation Information (w.r.t No Phase Segregation)

CDC Class: ACT
Attribute Type FC Enumeration Comment X
Trip or start has
general BOOLEAN ST
happened
Quality of the protection
q Quality ST
activation information
Timestamp of the last
change in state of
t TimeStamp ST
protection activation
information

2.5.7 Common Data Class: ACT_SEG

Description: Protection Activation Information (w.r.t Phase Segregation)

CDC Class: ACT
Attribute Type FC Enumeration Comment X
Trip or start has
general BOOLEAN ST
happened
Trip or start event of
phsA BOOLEAN ST
Phase A has happened
Trip or start event of
phsB BOOLEAN ST
Phase B has happened
Trip or start event of
phsC BOOLEAN ST
Phase C has happened
Quality of the protection
q Quality ST
activation information
Timestamp of the last
change in state of
t TimeStamp ST
protection activation
information

2.5.8 Common Data Class: ACT_SEG_NEU

Description: Protection Activation Information (w.r.t Phsae Segregation + Neutral)

CDC Class: ACT
Attribute Type FC Enumeration Comment X
Trip or start has
general BOOLEAN ST
happened
Trip or start event of
phsA BOOLEAN ST
Phase A has happened
Trip or start event of
phsB BOOLEAN ST
Phase B has happened
PICS & MICS P44x/EN PM/A11

MiCOM P442 & P444 (PM) 27

Attribute Type FC Enumeration Comment X

Trip or start event of
phsC BOOLEAN ST
Phase C has happened
Trip or start event with
neut BOOLEAN ST earth current has
happened
Quality of the protection
q Quality ST
activation information
Timestamp of the last
change in state of
t TimeStamp ST
protection activation
information

2.5.9 Common Data Class: CMV_MAG_ANG_FLOAT

Description: Complex Measured value (w.r.t Floating Point Magnitude and Angle)
CDC Class: CMV
Attribute Type FC Enumeration Comment X
Deadbanded complex
measured vector. Updated
to the current value of
Vector_Magnitude
cVal MX instCVal when the value
Angle_ Float
has changed according to
the configuration
parameter db
Quality of the
q Quality MX
measurement value
Time deadbanded
magnitude last exceeded
t TimeStamp MX
its db configuration
parameter
Unit of the attribute
units Unit_No_Multiplier CF
representing the data
db INT32U CF Measurement deadband

2.5.10 Common Data Class: CMV_MAG_FLOAT

Description: Complex Measured value (w.r.t Floating Point Magnitude)

CDC Class: CMV
Attribute Type FC Enumeration Comment X
Deadbanded complex
measured vector.
Updated to the current
Vector_Magnitude value of instCVal when
cVal MX
_Float the value has changed
according to the
configuration parameter
db.
Quality of the
q Quality MX
measurement value
Time deadbanded
magnitude last exceeded
t TimeStamp MX
its db configuration
parameter
Unit of the attribute
units Unit_No_Multiplier CF
representing the data
db INT32U CF Measurement deadband

2.5.11 Common Data Class: DEL_SEG_ANG

Description: Phase to phase measurements for a 3-Phase system (w.r.t Phase Seggregation
Angle)
CDC Class: DEL
Attribute Type FC Enumeration Comment X
Measurement values for
phsAB CMV_MAG_ANG_FLOAT --
Phase A to Phase B
Measurement values for
phsBC CMV_MAG_ANG_FLOAT --
Phase B to Phase C
Measurement values for
phsCA CMV_MAG_ANG_FLOAT --
Phase C to Phase A
P44x/EN PM/A11 PICS & MICS

(PM) 28 MiCOM P442 & P444

2.5.12 Common Data Class: DPC_STATUS

Description: Controllable Double Point (w.r.t Status Only)

CDC Class: DPC
Attribute Type FC Enumeration Comment X
Status value of the data
CODED_ENUM
stVal ST enumPos (Intermediate state, Off,
MMS Type: _BSTR2
On or Bad-state)
q Quality ST Quality of the status value
Timestamp of the last
t TimeStamp ST change in state of status
value
Control model
ENUMERATED8
ctlModel CF enumCtlModel (Corresponding to the
MMS Type: INT8
behaviour of the data)

2.5.13 Common Data Class: DPL_STANDARD

Description: Standard Device Name Plate

CDC Class: DPL
Attribute Type FC Enumeration Comment X
vendor VISIBLE_STRING255 DC Name of the vendor
hwRev VISIBLE_STRING255 DC Hardware revision
swRev VISIBLE_STRING255 DC Software revision
serNum VISIBLE_STRING255 DC Serial Number
model VISIBLE_STRING255 DC Model Number
Physical location of
location VISIBLE_STRING255 DC
device

2.5.14 Common Data Class: INC_MOD

Description: Controllable Integer Status (w.r.t Mode)

CDC Class: INC
Attribute Type FC Enumeration Comment X
INT32
stVal ST enumBeh_Mode Status value of the data
MMS Type: INT8
q Quality ST Quality of the status value
Timestamp of the last
t TimeStamp ST change in state of status
value
Control model
ENUMERATED8
ctlModel CF enumCtlModel (Corresponding to the
MMS Type: INT8
behaviour of the data)

2.5.15 Common Data Class: INC_MOD_D

Description: Controllable Integer Status (w.r.t Mode, with description)

CDC Class: INC
Attribute Type FC Enumeration Comment X
INT32
stVal ST enumBeh_Mode Status value of the data
MMS Type: INT8
Quality of the status
q Quality ST
value
Timestamp of the last
t TimeStamp ST change in state of status
value
Control model
ENUMERATED8
ctlModel CF enumCtlModel (Corresponding to the
MMS Type: INT8
behaviour of the data)
Description of the status
d VISIBLE_STRING255 DC
element
PICS & MICS P44x/EN PM/A11

MiCOM P442 & P444 (PM) 29

2.5.16 Common Data Class: INS_AR_STATE

Description: Integer Status (w.r.t Auto Reclose Status)

CDC Class: INS
Attribute Type FC Enumeration Comment X
INT32
stVal ST enumARState The element status
MMS Type: INT8
The quality of the status
q Quality ST
value
Timestamp of the last
t TimeStamp ST
change in state

2.5.17 Common Data Class: INS_BASIC

Description: Integer Status (w.r.t Mandatory Options Only)

CDC Class: INS
Attribute Type FC Enumeration Comment X
stVal INT32 ST The element status
The quality of the status
q Quality ST
value
Timestamp of the last
t TimeStamp ST
change in state

2.5.18 Common Data Class: INS_BEH

Description: Integer Status (w.r.t Behaviour)

CDC Class: INS
Attribute Type FC Enumeration Comment X
INT32
stVal ST enumBeh_Mode The element status
MMS Type: INT8
The quality of the status
q Quality ST
value
Timestamp of the last
t TimeStamp ST
change in state

2.5.19 Common Data Class: INS_BEH_D

Description: Integer Status (w.r.t Behaviour, with Description)

CDC Class: INS
Attribute Type FC Enumeration Comment X
INT32
stVal ST enumBeh_Mode The element status
MMS Type: INT8
The quality of the status
q Quality ST
value
Timestamp of the last
t TimeStamp ST
change in state
Description of the status
d VISIBLE_STRING255 DC
element

2.5.20 Common Data Class: INS_HEALTH

Description: Integer Status (w.r.t health)

CDC Class: INS
Attribute Type FC Enumeration Comment X
INT32
stVal ST enumHealth The element status
MMS Type: INT8
The quality of the status
q Quality ST
value
Timestamp of the last
t TimeStamp ST
change in state
P44x/EN PM/A11 PICS & MICS

(PM) 30 MiCOM P442 & P444

2.5.21 Common Data Class: LPL_LLN0

Description: Logical Node 0 Name Plate

CDC Class: LPL
Attribute Type FC Enumeration Comment X
vendor VISIBLE_STRING255 DC Name of the vendor
swRev VISIBLE_STRING255 DC Software revision
d VISIBLE_STRING255 DC Description
Uniquely identifies the
configRev VISIBLE_STRING255 DC configuration of a local
device instance
Logical Device name
ldNs VISIBLE_STRING255 EX
space

2.5.22 Common Data Class: LPL_LLNO_LNPRIV

Description: Logical Node 0 Name Plate (w.r.t Areva Extended)

CDC Class: LPL
Attribute Type FC Enumeration Comment X
vendor VISIBLE_STRING255 DC Name of the vendor
swRev VISIBLE_STRING255 DC Software revision
d VISIBLE_STRING255 DC Description
Uniquely identifies the
configRev VISIBLE_STRING255 DC configuration of a local
device instance
Logical Device name
ldNs VISIBLE_STRING255 EX
space
Logical Node name
lnNs VISIBLE_STRING255 EX
space

2.5.23 Common Data Class: LPL_LN

Description: Standard Logical Node Name Plate

CDC Class: LPL
Attribute Type FC Enumeration Comment X
vendor VISIBLE_STRING255 DC Name of the vendor
swRev VISIBLE_STRING255 DC Software revision
d VISIBLE_STRING255 DC Description

2.5.24 Common Data Class: LPL_LN_PRIV

Description: Logical Node Name Plate (w.r.t Areva Extended)

CDC Class: LPL
Attribute Type FC Enumeration Comment X
vendor VISIBLE_STRING255 DC Name of the vendor
swRev VISIBLE_STRING255 DC Software revision
d VISIBLE_STRING255 DC Description
Logical Node name
lnNs VISIBLE_STRING255 EX
space
PICS & MICS P44x/EN PM/A11

MiCOM P442 & P444 (PM) 31

2.5.25 Common Data Class: MV_FLOAT

Description: Measured value (w.r.t. Floating Point value)

CDC Class: MV
Attribute Type FC Enumeration Comment X
Deadbanded
magnitude of the
instantaneous value of
a measured value or
harmonic value.
mag AnalogueValue_Float MX Updated to the current
value of instMag when
the value has changed
according to the
configuration parameter
db
Quality of the
q Quality MX
measurement value
Time deadbanded
magnitude last
t TimeStamp MX
exceeded its db
configuration parameter
Unit of the attribute
units Unit_No_Multiplier CF
representing the data
Measurement
db INT32U CF
deadband

2.5.26 Common Data Class: MV_FLOAT_D

Description: Measured value (w.r.t Floating Point Value with Description)

CDC Class: MV
Attribute Type FC Enumeration Comment X
Deadbanded magnitude
of the instantaneous
value of a measured
value or harmonic value.
Updated to the current
mag AnalogueValue_Float MX
value of instMag when
the value has changed
according to the
configuration parameter
db
Quality of the
q Quality MX
measurement value
Time deadbanded
magnitude last exceeded
t TimeStamp MX
its db configuration
parameter
Unit of the attribute
units Unit_No_Multiplier CF
representing the data
db INT32U CF Measurement deadband
Description of the status
d VISIBLE_STRING255 DC
element

2.5.27 Common Data Class: SEQ_MAG

Description: Sequence components of a measurement value (w.r.t Magnitudes)

CDC Class: SEQ
Attribute Type FC Enumeration Comment X
Sequence component 1
c1 CMV_MAG_FLOAT -- (For semantic meaning
see seqT)
Sequence component 2
c2 CMV_MAG_FLOAT -- (For semantic meaning
see seqT)
Sequence component 3
c3 CMV_MAG_FLOAT -- (For semantic meaning
see seqT)
P44x/EN PM/A11 PICS & MICS

(PM) 32 MiCOM P442 & P444

Attribute Type FC Enumeration Comment X

Sequence quantity
ENUMERATED8 measurement type (Pos-
seqT MX enumSequenceComponent
MMS Type: INT8 Neg-Zero or Dir-Quad-
Zero)

2.5.28 Common Data Class: SPC_STATUS

Description: Controllable Single Point (w.r.t Status Only)

CDC Class: SPC
Attribute Type FC Enumeration Comment X
stVal BOOLEAN ST Status value of the data
q Quality ST Quality of the status value
Timestamp of the last
t TimeStamp ST change in state of status
value
Control model
ENUMERATED8
ctlModel CF enumCtlModel (Corresponding to the
MMS Type: INT8
behaviour of the data)

2.5.29 Common Data Class: SPS_D

Description: Standard Single Point Status (with Description)

CDC Class: SPS
Attribute Type FC Enumeration Comment X
The element status
stVal BOOLEAN ST
(TRUE or FALSE)
The quality of the status
q Quality ST
value
Timestamp of the last
t TimeStamp ST
change in state
Description of the status
d VISIBLE_STRING255 DC
element

2.5.30 Common Data Class: SPS_WD

Description: Single Point Status (without Description)

CDC Class: SPS
Attribute Type FC Enumeration Comment X
stVal BOOLEAN ST The element status (TRUE
or FALSE)
q Quality ST The quality of the status
value
t TimeStamp ST Timestamp of the last
change in state

2.5.31 Common Data Class: WYE_RES_ANG_D

Description: Phase to ground measurements for a 3-Phase system

(w.r.t Residual + Description + Angle)
CDC Class: WYE
Attribute Type FC Enumeration Comment X
res CMV_MAG_ANG_FLOAT -- Measurement values for
the residual system
current
d VISIBLE_STRING255 DC Description of the status
element

2.5.32 Common Data Class: WYE_SEG

Description: Phase to ground measurements for a 3-Phase system (w.r.t Phase Seggregation)
CDC Class: WYE
Attribute Type FC Enumeration Comment X
Measurement values for
phsA CMV_MAG_FLOAT --
Phase A
Measurement values for
phsB CMV_MAG_FLOAT --
Phase B
PICS & MICS P44x/EN PM/A11

MiCOM P442 & P444 (PM) 33

Attribute Type FC Enumeration Comment X

Measurement values for
phsC CMV_MAG_FLOAT --
Phase C

2.5.33 Common Data Class: WYE_SEG_RES_D

Description: Phase to ground measurements for a 3-Phase system

(w.r.t Phase Seggregation + Residual + Description)
CDC Class: WYE
Attribute Type FC Enumeration Comment X
Measurement values for
phsA CMV_MAG_ANG_FLOAT --
Phase A
Measurement values for
phsB CMV_MAG_ANG_FLOAT --
Phase B
Measurement values for
phsC CMV_MAG_ANG_FLOAT --
Phase C
Measurement values for
neut CMV_MAG_ANG_FLOAT --
neutral input
Description of the status
d VISIBLE_STRING255 DC
element
P44x/EN PM/A11 PICS & MICS

(PM) 34 MiCOM P442 & P444

2.6 Common data attribute type definitions

Common data attribute types, known herein as components, are defined for use in the
Common Data Classes defined in the sections above.

2.6.1 Component: AnalogueValue_Float

Comment: General analogue value (w.r.t Floating Point value)

Parent Type: AnalogueValue
Attribute Type Enumeration Comment X
f FLOAT32 Floating point value

2.6.2 Component: Unit_No_Multiplier

Comment: SI Unit definitions

Parent Type: Unit
Attribute Type Enumeration Comment X
SIUnit ENUMERATED16 enumUnits SI Unit

2.6.3 Component: Vector_Magnitude_Float

Comment: Complex vector (w.r.t Floating Point Magnitude value)

Parent Type: Vector
Attribute Type Enumeration Comment X
The magnitude of the
mag AnalogueValue_Float
complex value

2.6.4 Component: Vector_MagnitudeAngle_Float

Comment: Complex vector (w.r.t Floating Point Magnitude and Angle values)
Parent Type: Vector
Attribute Type Enumeration Comment X
mag AnalogueValue_Float The magnitude of the
complex value
ang AnalogueValue_Float The angle of the
complex value (the
unit is degrees)
PICS & MICS P44x/EN PM/A11

MiCOM P442 & P444 (PM) 35

2.7 Enumerated type definitions

The following sub-sections specify the enumerations that are associated to some Common
Data Class attributes. The definition of the enumerations are according to IEC61850-7-3 and
IEC61850-7-4 unless otherwise stated.

2.7.1 Enumerated type: enumARState

Description: Auto-Reclose State

Ordinal Semantic
1 Ready
2 In Progress
3 Successful

2.7.2 Enumerated type: enumBeh_Mode

Description: Behaviour/Mode
Ordinal Semantic
1 On
2 Blocked
3 Test
4 Test / Blocked
5 Off

2.7.3 Enumerated type: enumCtlModel

Description: Control Model

Ordinal Semantic
0 Status only
1 Direct with normal security
2 sbo with normal security
3 Direct with enhanced security
4 sbo with enhanced security

2.7.4 Enumerated type: enumDirectionGeneral

Description: General Direction

Ordinal Semantic
1 Unknown
2 Forward
3 Reverse
4 Both

2.7.5 Enumerated type: enumDirectionPhase

Description: Phase Direction

Ordinal Semantic
1 Unknown
2 Forward
3 Reverse

2.7.6 Enumerated type: enumHealth

Description: Health
Ordinal Semantic
1 OK
2 Warning
3 Alarm
P44x/EN PM/A11 PICS & MICS

(PM) 36 MiCOM P442 & P444

2.7.7 Enumerated type: enumPos

Description: CB position
Ordinal Semantic
0 Intermediate
1 Off
2 On
3 Bad-state

2.7.8 Enumerated type: enumSequenceComponent

Description: Sequence Measurement Type

Ordinal Semantic
1 Pos_Neg_Zero
2 Dir_Quad_Zero

2.7.9 Enumerated type: enumUnits

Description: SI Units derived from ISO/IEC 1000

Ordinal Semantic
1 none
2 m
3 kg
4 s
5 A
6 K
7 mol
8 cd
9 deg
10 rad
11 sr
21 Gy
22 q
23 °C
24 Sv
25 F
26 C
27 S
28 H
29 V
30 Ohm
31 J
32 N
33 Hz
34 lx
35 Lm
36 Wb
37 T
38 P
39 Pa
41 m²
42 m³
43 ms¯¹
44 ms¯²
45 m³s¯¹
46 ms³
47 M
48 kg/m³
49 m²/s
50 W/mK
51 J/K
PICS & MICS P44x/EN PM/A11

MiCOM P442 & P444 (PM) 37

Ordinal Semantic
52 ppm
53 s¯¹
54 rads¯¹
61 VA
62 W
63 VAr
64 theta
65 cos(theta)
66 Vs
67 V²
68 As
69 A²
70 A²t
71 VAh
72 Wh
73 VArh
74 V/Hz
P44x/EN PM/A11 PICS & MICS

(PM) 38 MiCOM P442 & P444

2.8 MMS Data-type conversions

The following table shows the relationships between the Part 7 and Part 8-1 data types. The
definitions presented above use Part 7 data types, however these are subject to 'translation'
when exposed over an MMS (Part 8-1) interface:
Part 7 Type MMS Type Part 7 Description
_BSTR1 Bstring1 Bit string 1
_BSTR16 Bstring16 Bit string 16
_BSTR2 Bstring2 Bit string 2
_BSTR32 Bstring32 Bit string 32
_BSTR8 Bstring8 Bit string 8
BOOLEAN Bool Logical TRUE/FALSE value
BVstring13 BVstring13 Variable bit string (upto 13 bits)
CODED_ENUM Byte Coded enumeration
CODED_ENUM2 Byte Coded enumeration (2)
EntryTime Btime6 8.1 Section 8.1.3.7
ENUMERATED16 Short 16 bit enumerated value
ENUMERATED8 Byte 8 bit enumerated value
FLOAT32 Float 32 bit floating point value
FLOAT64 Double 64 bit floating point value
INT128 Long 128 bit signed integer value
INT16 Short 16 bit signed integer value
INT16U Ushort 16 bit unsigned integer value
INT24U Ulong 24 bit unsigned integer value
INT32 Long 32 bit signed integer value
INT32U Ulong 32 bit unsigned integer value
INT8 Byte 8 bit signed integer value
INT8U Ubyte 8 bit unsigned integer value
OCTET_STRING64 OVstring64 64 character string (8 bits per character)
OCTET_STRING8 OVstring8 8 character string (8 bits per character)
Quality BVstring13 IEC61850 Quality
RTYP_BOOL Bool Reporting type - BOOLEAN
RTYP_BSTR6 Bstring6 Reporting type - 6 bit string
RTYP_BSTR8 Bstring8 Reporting type - 8 bit string
RTYP_BSTR9 Bstring9 Reporting type - 9 bit string
RTYP_BTIME6 Btime6 Reporting type - 6 byte timestamp
RTYP_BVSTR10 BVstring10 Reporting type - Variable bit string (upto 10 bits)
RTYP_BVSTR6 BVstring6 Reporting type - Variable bit string (upto 6 bits)
RTYP_BVSTR8 Bvstring8 Reporting type - Variable bit string (upto 8 bits)
RTYP_INT16U Ushort Reporting type - 16 bit unsigned integer value
RTYP_INT32U Ulong Reporting type - 32 bit unsigned integer value
RTYP_INT8U Ubyte Reporting type - 8 bit unsigned integer value
RTYP_OSTR8 Ostring8 Reporting type -8 character string (8 bits per character)
RTYP_VSTR32 Vstring32 Reporting type - 32 character string
RTYP_VSTR65 Vstring65 Reporting type - 65 character string
TimeStamp Utctime IEC61850 Time stamp
UNICODE_STRING255 UTF8Vstring255 255 character string (16 bits per unicode character)
UTC_TM Utctime UTC Timestamp
VISIBLE_STRING255 Vstring255 255 character string
VISIBLE_STRING64 Vstring64 64 character string
VISIBLE_STRING65 Vstring65 65 character string
VISIBLE_STRING97 Vstring97 97 character string
Publication: P44X/EN PM/A11

AREVA T&D's Automation & Information Systems Business www.areva-td.com

T&D Worldwide Contact Centre online 24 hours a day: +44 (0) 1785 25 00 70 http://www.areva-td.com/contactcentre/