Scribd
Upload
156 views9 pages

Test 2 - TB17094 - Nabil PDF

The document is a confidential test paper for a Power Electronics course consisting of 3 questions. It provides instructions for students taking the test, noting it is 1.5 hours long and contains 3 questions that must all be answered. The questions cover designing converters and inverters based on given circuit diagrams and specifications, determining component values, and calculating current and power characteristics.

Uploaded by

Muhammad Nabil
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
156 views9 pages

Test 2 - TB17094 - Nabil PDF

The document is a confidential test paper for a Power Electronics course consisting of 3 questions. It provides instructions for students taking the test, noting it is 1.5 hours long and contains 3 questions that must all be answered. The questions cover designing converters and inverters based on given circuit diagrams and specifications, determining component values, and calculating current and power characteristics.

Uploaded by

Muhammad Nabil
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 9

CONFIDENTIAL

FACULTY OF ELECTRICAL & ELECTRONICS ENGINEERING


TECHNOLOGY

TEST II

COURSE : POWER ELECTRONICS

COURSE CODE : BTE4743

LECTURER : NORAZILA BINTI JAALAM

DATE : 28 JULY 2020

DURATION : 1 HOUR AND 30 MINUTES

SEMESTER / SESSION : SEMESTER II / SESSION 2019/2020

PROGRAM CODE : BTE

INSTRUCTIONS TO CANDIDATE:

1. This question paper consists of THREE (3) questions. Answer ALL questions.
2. All answers to a new question should start on new page.
3. All the calculations and assumptions must be clearly stated.

TEST REQUIREMENTS:

1. NIL

DO NOT TURN THIS PAGE UNTIL YOU ARE TOLD TO DO SO

This examination paper consists of THREE (3) printed pages including the front page.
CONFIDENTIAL BTE/1920/II BTE4743

QUESTION 1

A converter in Figure 1 has an output voltage of 25 V when the input is 50 V. If the load
is 125 W, design a converter to limit the peak inductor current to 6.25 A. Then, determine
the value of capacitance to limit the output voltage ripple to 5%. Specify the switching
frequency (add all digits in your student ID number e.g.: TB17099, fsw = 26 kHz) and
design for a continuous inductor current.
[12 Marks]
[CO2, PO3, C4]

Figure 1

QUESTION 2

Design a flyback converter as in Figure 2 for an input of 25 V and an output of 40 W at


40 V. If the ripple factor is limited to 2% and the current variation in magnetizing
inductance is 40% of the average current, specify:
i) the switching frequency (add all digits in your student ID number e.g.: TB17099,
fsw = 26 kHz)
ii) the transformer turns ratio
iii) the magnetizing inductance
iv) the capacitor value
[14 Marks]
[CO2, PO3, C4]

2
CONFIDENTIAL BTE/1920/II BTE4743

Figure 2

QUESTION 3

Figure 3 is a square-wave inverter that has a RL load with R = 15 Ω and L = 10 mH. The
inverter output frequency is 400 Hz. Design an inverter to establish a load current that
has a fundamental frequency component of 8 A rms.
i) Determine the value of the DC source, Vdc
ii) Determine the amplitudes of the Fourier series terms for the load current and load
voltage until 7th order harmonics
iii) Determine the power absorbed by the load

Figure 3
[14 Marks]
[CO2, PO3, C4]

END OF QUESTION PAPER

3
CONFIDENTIAL BTE/1920/II BTE4743

4
CONFIDENTIAL BTE/1920/II BTE4743

5
CONFIDENTIAL BTE/1920/II BTE4743

6
CONFIDENTIAL BTE/1920/II BTE4743

7
CONFIDENTIAL BTE/1920/II BTE4743

8
CONFIDENTIAL BTE/1920/II BTE4743

You might also like