CSM-321S

CS1-PR PROCESS Indicator

„ DESCRIPTION
CS1-PR economic type Process Indicator has been designed

CS2-VA
with high accuracy measurement, display and
communication of DC signal 0~10V and 4(0)~20mA.
They are also available 1 option of 1 Relay outputs, 1
Analogue output or 1 RS485(Modbus RTU Mode) interface
with versatile functions such as control, alarm,

CSM- CSM-321S CSM-

re-transmission or communication for a wide range of
industrial applications.
„ FEATURE
● Measuring linear signal 0~10V and 0(4)~20mA in one indicator(input code: AV)
● Square Root function available by programming
● Option available 1 of 1 relay, 1 analogue output or RS485(Modbus RTU mode)
● 1 relay can be programmed individual to be a Hi / Lo / Hi Latch / Lo Latch energized with Start
Delay / Hysteresis / Energized & De-energized Delay functions.
● Analogue output or RS 485 communication port in option
● CE Approved & RoHS

„ ORDERING INFORMATION Excitation Supply DC24V in build for 2 wire transmitters

CS1-PR
− − −
Input Optional Excitation Aux.
CS1−PR− Signal Output Supply Powered
OPTION

CODE INPUT RANGE CODE OPTIONAL O/P CODE EXCIT. SUPPLY CODE AXU. POWER
A1 0(4) ~ 20mA / 0 ~ 10mA N None N None A AC115/230V
V1 0 ~ 10V / 0(1) ~ 5V R1 1 Relay E24 DC 24V OPTION 4

CSM-321S CSM- CSM-321S CSM- CSM-321S CSM-

AV 0~10V/0(4)~20mA(all in one) 0(1) ~ 5 V EO Specify ADH* AC/DC 85~264V * It means RoHS
V 0 ~ 10 V version.
AO Specify A input ADL* AC/DC 20~90V
VO Specify V input 0 ~ 10 mA * ADH* will be available
I 0(4)~20 mA at Jan. 2008
8 RS 485
Relay, Analogue Output
or RS485 Port can be
selected one only.

Digital fine adjust: Pv.Zro: Settable range: -19999~+29999

„ TECHNICAL SPECIFICATION Pv.SPn: Settable range: -19999~+29999
Input
Input Input Reading Stable Function
Input Range Input Range
Impedance Impedance Average: Settable range: 1~99 times
Voltage 0 ~ 10 V ≥ 1M ohm Current 4(0)~20 mA 250 ohm Moving average: Settable range: 1(None)~10 times
¾ The Meter can be 0~10V and 0~20mA in one unit, according to connection #11 or #12 Digital filter: Settable range: 0(None)/1~99 times

Calibration: Digital calibration by front key Control Functions(option)

A/D converter: 16 bits resolution Set-points: One set-point
Accuracy: ≤± 0.04% of FS ± 1C; Control relay: 1 Relay, FORM-C, 5A/230Vac, 10A/115V
Sampling rate: 15 cycles/sec Relay energized mode: Energized levels compare with set-points:
Response Time: ≤100 msec.(when the AvG = “1”) in standard Hi / Lo / Hi.HLd / Lo.HLd programmable
Input type: 0~10V / 0~5V / 1~5V / 0-10mA / 0~20mA / 4~20mA Energizing functions: Start delay / Energized & De-energized delay / Hysteresis
programmable for coding AV(option) Energized Latch
Start band(Minimum level for Energizing): 0~9999counts
Display & Functions Start delay time: 0:00.0~9(Minutes):59.9(Second)
LED: Numeric: 5 digits, 0.8”(20.0mm)H red high-brightness LED Energized delay time: 0.00.0~9(Minutes):59.9(Second)
Relay output indication: 1 square red LED De-energized delay time: 0.00.0~9(Minutes):59.9(Second)
RS 485 communication: 1 square orange LED Hysteresis: 0~5000 counts
E.C.I. function indication: 1 square green LED
Max/Mini Hold indication: 2 square orange LED Analogue output(option)
Down key function indication(Reset for Max.(Mini.) Hold / Accuracy: ≤± 0.1% of F.S.;
PV Hold / Rel. PV): 1 square green LED Ripple: ≤± 0.1% of F.S.
Display range: -19999~29999; Response time: ≤100 msec. (10~90% of input)
Scaling function: Lo.SC: Low Scale; Settable range: -19999~+29999 Isolation: AC 2.0 KV between input and output
Hi.SC: High Scale; Settable range: -19999~+29999 Output range: Specify either Voltage or Current output in ordering
Decimal point: Programmable from 0 / 0.0 / 0.00 / 0.000 / 0.0000 Voltage: 0~5V / 0~10V / 1~5V programmable
Over range indication: ovFL, when input is over 120% of input range Hi Current: 0~10mA / 0~20mA / 4~20mA programmable
Under range indication: -ovFL, when input is under -20% of input range Lo Output capability: Voltage: 0~10V: ≥ 1000Ω;
Max / Mini recording: Maximum and Minimum value storage during power on. Current: 4(0)~20mA: ≤ 600Ω max
Display functions: PV / Max(Mini) Hold / RS 485 Programmable Functions: Ao.HS(output range high): Settable range: -19999~29999
Front key functions: Relative PV / PV Hold / Reset for maxi(mini) hold / Ao.LS(output range Low): Settable range: -19999~29999
Reset for relay energized latch programmable Digital fine adjust: Ao.Zro: Settable range: -38011~+27524
Low cut: Settable range: -19999~29999 counts Ao.SPn: Settable range: -38011~+27524

C1-01-1/7-2007-11-07
 CSM-321S

RS 485 Communication(option)
Protocol: Modbus RTU mode „ INSTALLATION
Baud rate: 1200/2400/4800/9600/19200/38400 programmable The meter should be installed in a location that dose not exceed the
8 bits
CS2-VA

Data bits: maximum operating temperature and provides good air circulation.
Parity: Even, odd or none (with 1 or 2 stop bit) programmable
Address: 1 ~ 255 programmable
Remote display: to show the value from RS485 command of master
Distance: 1200M RL COM
CI1

Terminate resistor: 150Ω at last unit.

? ? ? Kg/cn
CSM- CSM-321S CSM-

ENT/FN

Electrical Safety FIX HOLDER:

Dielectric strength: AC 2.0 KV for 1 min, Between Power / Input / Output / Case PANEL CUT-OUT: 63 mm(L) / W M3
92+0.2(W) x 44+0.2(H) mm
Insulation resistance: ≥100M ohm at 500Vdc, Between Power / Input / Output 1.0~8.0 mm
Isolation: Between Power / Input / Relay, Analogue, RS485
EMC: EN 55011:2002; EN 61326:2003
Safety(LVD): EN 61010-1:2001 „ CONNECTION DIAGRAM
Relay, Analogue o/p Relay Terminal blocks:
Environmental 10A/300Vac, M2.6,
or RS485 port can be
Operating temp.: 0~60 ˚C selected one only. b c a 1.3~2.0mm2 (16~12AWG)
Operating humidity: 20~95 %RH, Non-condensing
11 12 13 14 15 16 4 5 6 7 8 9 10
Temp. coefficient: ≤100 PPM/˚C
Storage temp.: -10~70 ˚C AC115V
Enclosure: Front panel: IEC 549 (IP54); Housing: IP20 0~20mA Excit. Analogue
AC230V
Supply FG ADH AC/DC 86~265V
output
0~10V DC24V ADL AC/DC 20~90V
Mechanical SIGNAL INPUT AUX. POWER
96mm(W) x 48mm(H) x 72mm(D) A B
Dimensions:
CS1-PR

RS 485 port
Panel cutout: 92mm(W) x 44mm(H)
Case materiel: ABS fire-resistance (UL 94V-0) Please check the voltage of power supplied first, and then connect
Mounting: Panel flush mounting to the specified terminals. It is recommended that power supplied to
Terminal block: Plastic NYLON 66 (UL 94V-0) the meter be protected by a fuse or circuit breaker.
10A 300Vac, M2.6, 1.3~2.0mm2(16~12AWG) Power Supply
Weight: 350g / 300g(Aux. Power Code: ADH or ADL)
6 7 8 9 10
CSM-321S CSM- CSM-321S CSM- CSM-321S CSM-

Power 1A Fuse
Power supply: AC115/230V,50/60Hz; L L AC115/230V
Optional: AC/DC 85~264V or 20~90V(RoHS version)
N N AC85~264V
G G
Excitation supply: DC24V/30mA maximum in standard
Filter or Transformer
Power Consumption: 4.5VA maximum
Back up memory: By EEPROM 2 wire Transmitter connection RS485 Communication Port
4~20mA 24Vdc
Input Excit.S
„ FRONT PANEL 11 12 13 14 15
Max. Distance: 1200M
Terminate Resistor
(at latest unit):
A B 120~300ohm/0.25W
Max. Hold status (typical: 150ohm)
Relay status
Indication RL1 COM
M.H
Comm. status 4 5 6
CI11

Front Key
RS485 Port
M.H function status
Display screen
ENT/FN ? ? ? Kg/cm 2 Mini. Hold status
Operation Key
Engineer Unit

„ FUNCTION DESCRIPTION
„ DIMENSIONS Input & Scaling Functions
Dual input types: (Option Code: AV)
Voltage and Current Type are in one unit available in option. If the
customer specify the input coding for AV, the meter will be calibrated for
FRONT VIEW 48.0 0~10V and 0~20mA in factory. The user can use in 0~10V or4(0)~20mA
by difference terminals connection(#11 & #13 for 0~10V or #12 & #13 for
4(0)~20mA) and programming in 【Ai.tYP】of【inPUt GroUP】.
96.0 8.0 60.0
12.0 Scaling function:
Setting the Lo.SC(Low scale) and Hi.SC(High scale) in【inPUt
Dimensions: 96mm x 48mm x 72mm GroUP】to relative input signal. Reverse scaling will be done too.
PANEL CUT-OUT 44.0+0.2 Panel Cutout: 93mm x 45mm (advise) Please refer to the figure as below,
SC ALE D e fa u lt: L o .S C : 0 .0 0 , H i.S C : 1 0 0 .0 0
Unit: mm C h a n g e to L o .S C : 5 0 .0 0 , H i.S C : 1 9 9 .9 9
92.0+0.2 1 9 9 .9 9
R e ve rs e s lo p

1 0 0 .0 0

5 0 .0 0

0 .0 0 IN P U T
0 .0 0 % 5 0 .0 0 % 1 0 0 .0 0 %
*Too narrow scale may course display lower resolution.

C1-01-2/7-2007-11-07
 Display & Functions Digital fine adjustment:
Max / Mini recording: The meter will storage the maximum and minimum value in Users can get Fine Adjustment for Zero & Span of PV by front key of
【User Level】during power on in order to review drifting the meter, and “Just Key In” the value which user want to show in
the current input signals.

CS2-VA
of PV.
Display functions: PV / Max(Mini) Hold / RS 485 programmable in Especially, the【Pv.Zro】&【Pv.SPn】are not only in zero & span of
(Please refer to step A-07) 【dSPLY】function of【inPUt GroUP】 PV, but also any lower point for
【Pv.Zro】& higher point for
【Pv.SPn】.
Present Value Pv: The display will show the value that The meter will be linearization for full scale.
Relative to Input signal. The adjustment can be clear in function【Z.S.CLr】.
Maximum Hold Max.H / Minimum Hold Mini.H : D e fa u lt In p u t: L o .S C : 0.0 0 , H i.S C : 1 9 9 .9 9
The meter will keep display in maximum(minimum) D ig ita l fin e ad ju t.: in p u t 2 .7 5 V ,

CSM- CSM-321S CSM-

S C A L E D isp la y: L o w p o in t fro m 5 5 .00 to 8 0 .0 0
value during power on, until press front key to reset H ig h p o in t fro m 18 0 .0 0 tp 1 7 0 .0 0
1 99 .9 9
(If the down key function in【inPUt GroUP】has 180.00
been set to M.rSt .) 170.00
1 50 .0 0
¾ Please find the M.H sticker that enclosure the
package of the meter to stick on the right side of 10 0 .0 0
square orange LED 80.00
M ax. ( M ini.) Hold & Reset 55.00
M axim um H old
P resent 0 .0 0 IN P U T
V alue 9.00V
0V 2.75V 5V 10V

Reading Stable Function

Reset the Max
(Mini) Hold by
Level O Average:
E.C.I. or F. Key Trigger N
Basically, the sampling rate of meter is 15cycles/sec. If the function
Remote Display by RS485 command RS485 : The set to be 3 times, It means the meter will update of display will be 5
meter will show the value that received from RS485 times/sec.

CS1-PR
sending. In past, The meter normally receive Average set to be 3
or 0~10V from AO or digital output from BCD module Sample 1 Sample 2 Sample 3 Sample 4 Sample 5 Sample 6 …….
of PLC .We support a new solution that PV shows
the value from RS485 command of master can so Display Update Value = Display Update Value =
(Sample 1 + Sample 2 + Sample 3)/3 (Sample 4 + Sample 5 + Sample 6)/3
that can be save cost and wiring from PLC.
Remark: The higher average setting will cause the response time of Relay and Analogue output slower.
Front key functions: Relative PV / PV Hold / Reset for maxi(mini) hold /

CSM-321S CSM- CSM-321S CSM- CSM-321S CSM-

Reset for relay energized latch programmable in Moving average:
【dn.KEY】function of 【inPUt GroUP】 If the function to be set 3 times, the meter will update delay in first 3
Relative PV rEL.Pv :【dn.KEY】function can be set to samples, then it will update 15 times/sec continuously.
be rEL.Pv function. When user press the key, Moving Average set to be 3
the display will show the differential value(∆PV), until Sample 1 Sample 2 Sample 3 Sample 4 Sample 5 Sample 6 …….
press key again. In first 3 samples, Display Update Value = (Sample 1 + Sample 2 + Sample 3)/3
¾ Please find the R.PV sticker to stick on the right
Display Update Value = (Sample 2 + Sample 3 + Sample 4)/3
side of square red LED.
PV Hold Pv. HLd :【dn.KEY】function can be set to Display Update Value = (Sample 3 + Sample 4 + Sample 5)/3

be Pv. HLd function. When user press the key, Display Update Value = (Sample 4 + Sample 5 + Sample 6)/3
the display will be hold until press the key again. Remark: The higher moving average setting wouldn’t cause the response time of Relay and Analogue
output slower after first 3 samples.
¾ Please find the PV.H sticker to stick on the right
side of square red LED. Digital filter: The digital filter can reduce the magnetic noise in field.
PV Hold & Reset
Present PV Hold Control functions(option)
Value Relay energized mode: Hi / Lo / Hi.HLd / Lo.HLd programmable
Hi: Relay will energize when PV > Set-Point
Lo: Relay will energize when PV < Set-Point
Reset PV Hold
Hi / Lo Relay Energized
O ON Edge ON
by Front
DownKey N Trigger Hi Setting

Reset for Max(Mini) Hold: when the【dSPLY】in

【inPUt GroUP】set to be Max.H or Mini.H ,
Lo Setting
【dn.KEY】function can be set to be M.rSt to reset
the display when it is holding in maxim or mini value. Hi Relay Energized ON
Reset for relay energized latch: when the【rY1.Md】in
Lo Relay Energized ON
【rELAY GroUP】set to be Hi.HLd or Lo.HLd ,
【dn.KEY】function can be set to be rY.rSt to reset Hi.HLd (Lo.HLd): When the PV is Higher (or lower) than
the relay when it is energizing and latching. set-point, the relay will be energized and latch until
Low cut: manual reset by from key in【User Level】or press
If the setting value is positive, it means when the absolutely value of down key to reset(If the 【dn.KEY】function set to
PV ≤ Setting value, the display will be 0. If the setting value is be rY.rSt)
negative, it means when the PV under setting value(PV≤ -Setting H i(Lo) E nergized Latch & R eset
value), the display will be setting value.
H i S ettin g
Low Cut set to be +0.50 Low Cut set to be -0.10
Present PV according Present PV according
Value to input signal Value to input signal

0.50 H i.H Ld (H igh H old)

Low cut Low cut R ela y E nerg ized ON
function function
-0.10 Reset the relay ON
Level Trigger
-0.50 Latch by Down Key

Low Cut is set for 0.50, if the PV is Low Cut is set for -0.10, if the PV is under
from -0.50~+0.50, that display will be 0. (< = -0.10), that display will be -0.10.

C1-01-3/7-2007-11-07
 Energized functions: Start delay / Energized & De-energized delay / Hysteresis RS 485 Communication(option)
Start Delay Energized / De-energized The RS485’s protocol is Modbus RTU mode, and baud rate up to
Delay & Hysteresis 38400 bps. It’s convenience to remote monitoring, display for
CS2-VA

Inhibit
Hi Setting
reading.
Inhibit

Energized delay time

De-energized
Hi Setting

delay time
Hysteresis RS 485 Modbus RTU Mode (up to 38400bps)

Analog Output 0~10V/0(4)~20mA

Start Band

Relay Relay
Energized Start Delay Time ON Energized ON 1 Relay Output:
Mode: High or Low Energized
Functions: Start delay / Energized &
De-energized delay / Hysteresis
CSM- CSM-321S CSM-

COM COM
RL1 RL1

Display:
Analogue output(option) ENT/FN ◄ ▲ ▼ RPM
EN ◄ ▲ ▼
Kg/cm
Mode: Measuring Value / Maximum Hold /
Minimum Hold / Reading value from
RS485 command

Please specify the output type either an o~10V or 4(0)~20mA in

ordering. The programmable output low and high scaling can be
based on various display values. Reverse slope output is possible by
reversing point positions.
Output range: Voltage: 0~5V / 0~10V / 1~5V programmable
Current: 0~10mA / 0~20mA / 4~20mA programmable
Functions: Ao.HS(output range high): setting the Display value High
to versus output range High(as like as 20mA in 4~20)
Ao.LS(output range Low): setting the Display value Low
to versus output range Low(as like as 4mA in 4~20) Remote display:
Set Scaling: Lo.SC: 0.00, Hi.SC: 199.99; The meter will show the value that received from RS485 command.
SCALE Output: Ao.LS: 50.00(Display Value Low), In past, The meter normally receive 4~20mA or 0~10V from AO or
Ao.HS: 150.00(Display Value High)
digital output from BCD module of PLC .We support a new solution
199.99
that PV shows the value from RS485 command of master so that
150.00 can be save cost and wiring from PLC.
CS1-PR

100.00 When the【dSPLY】set to be RS485, it means, the PV screen will

show the number from RS485 command & data. The data(number)
50.00 will be same as PV that will compare with set-point, analogue output
0.00 and ECI functions so that is to control analogue output, relay
0.00% 50.00% OUTPUT 100.00% energized and so on.
The range between Ao.HS and Ao.LS should be over CS1 APPLICATION FOR REMOTE DISPLAY FROM RS485 COMMAND
CSM-321S CSM- CSM-321S CSM- CSM-321S CSM-

20% of span at least; otherwise, it will be got less

resolution of analogue output. RS 485 Modbus RTU Mode (up to 38400bps)

RS485 wiring 1.2KM maximum

Fine zero & span adjustment: Terminate Resistor:

Users can get Fine Adjustment of analogue output by front key of

the meter. Please connect standard meter to the terminal of
analogue output. To press the front key(up or down key) of meter to RL1 COM
CI11
M.H
RL1 COM
CI11
M.H

adjust and check the output of meter. ENT/FN ◄ ▲ ▼ Kg/cm

M.H

2
ENT/FN ◄ ▲ ▼ Kg/cm
M.H

【Ao.Zro】: Fine Zero Adjustment for Analog Output;

Settable range: -38011~27524;
【Ao.Spn】: Fine Span Adjustment for Analog Output;
Settable range: -38011~27524;

„ ERROR MASAGE
DESCRIPTION DISPLAY FLASH REMARK
BEFORE POWER ON, PLEASE CHECK THE SPECIFICATION AND
CONNECTION AGAIN.
SELF-DIAGNOSIS AND ERROR CODE:
: Display is positive-overflow (Signal is over display range) (Please check the input signal)
: Display is negative-overflow (Signal is under display range) (Please check the input signal)
: ADC is positive-overflow (Signal is higher than input 120%) (Please check the input signal)
: ADC is negative-overflow (Signal is lower than input -120%) (Please check the input signal)
: EEPROM occurs error (Please send back to
/ manufactory for repaired)
: Calibrating Input Signal do not process (Please process Calibrating
/ Input Signal)
: Calibrating Input Signal error (Please check Calibrating Input
/ Signal)
(Please process Calibrating
/ : Calibrating Output Signal do not process Output Signal)
(Please check Calibrating
/ : Calibrating Output Signal error Output Signal)

C1-01-4/7-2007-11-07
„ FRONT PANEL:
„ Operating Key: 4 keys for Enter(Function) /

CS2-VA
Relay status Max. Hold status
Indication RL1 COM
M.H
Comm. status Shift(Escape) / Up key / Down key
CI11

Front Key Setting Status Function Index

M.H function status Increase number Go back to previous
Display screen Up key
ENT/FN ? ? ? Kg/cm2 Mini. Hold status function index
Operation Key
Engineer Unit Down key Decrease number Go to next

CSM- CSM-321S CSM-

function index
Shift key Shift the setting Go back to this function
„ Numeric Screens position index, and abort the
0.8”(20.0mm) red high-brightness LED for 5 digital present setting
value. Enter/Fun Setting Confirmed From the function index
„ I/O Status Indication key and save to to get into setting status
z Relay Energized: 1 square red LED EEProm
RL1 display when Relay 1 energized; „ Pass Word: Settable range:0000~9999;
z RS485 Communication: 1 square orange LED User has to key in the right pass word so that get into
COM will flash when the meter is receive or send data, and COM 【Programming Level】. Otherwise, the meter will go back to
flash quickly means the data transient quicker. measuring page. If user forgets the password, please contact
z Max/Mini Hold indication: 2 square orange LEDs with the service window.
CO M.H displayed: When the display function has been selected „ Function Lock: There are 4 levels programmable.
in Maximum or Minimum Hold function. z None: no lock all.

CS1-PR
„ Stickers: z User Level: User Level lock. User can get into User Level for
Each meter has a sticker what are functions and engineer checking but setting.
label enclosure. z Programming Level: Programming level lock. User can get
into programming level for checking but setting.
z Relay energized mode: H H H i L o L L D O
z ALL: All lock. User can get into all level for checking but
z Down key functions mode:
setting.

CSM-321S CSM- CSM-321S CSM- CSM-321S CSM-

PV.H(PV Hold) / Tare / DI(Digital Input)
„ Front Key Function
M.RS(Maximum or Minimum Reset) /
z The Key can be set to be rEL.Pv / Pv.HLd / M.rSt /
R.RS(Reset for Relay Latch)
rY.rSt programmable.
z Engineer Label: over 80 types.

C1-01-5/7-2007-11-07
 „ OPERATING DIAGRAM (The detail description of operation, please refer to operating manual.)
Power ON
CS2-VA

Self-diagnosis
User Level
Press for 1 sec. can back to Measuring
Show the This page will Min:PV model number

0−0−1

0−3

0−6
model number show out, Minimum firmware
CSM- CSM-321S CSM-

when dSPLY storage version

set to be Checking only Checking only
RS485.
Pv: Present
Value
Show rY.1.SP.: Relay MAX:PV Cyclic to first
0−1

0−4

0−0−1
the firmware 1 Set-point Maximum page
version setting storage
-19999~+29999 Checking only
MEASURING rY.rSt: Reset M.rSt: Reset
0−2

0−5
PAGE for energized for Maximum &
Press 1sec Latch of Relay Minimum
YES no storage
Press 1sec
ENT YES no
Enter the
password to
access
CS1-PR

ENT
programming
Level

NO
Pass Code
Programming Level
YES

Default:1000 Press for 1 sec. can back to Measuring

▼
▲
CSM-321S CSM- CSM-321S CSM- CSM-321S CSM-

▼
INPUT RELAY ANALOGUE RS485
GROUP GROUP OUTPUT GROUP
▲

ENT ENT ENT GROUP ENT

Ai.tYP: rY.Sb: Start Ao.Typ: Adres: Device

Analogue band for Relay Analogue number of the
A−0

B−1

D−1

E−1

Input type energized Output type meter

selection 0~9999counts selection 1~255
v.0-10 v. 0~5 v.0-10 v. 0~5
v.1-5 A.0-10 v.1-5 A.0-20
A.0-20 A.4-20 A.4-20 A.0-10
Pv.dP: rY.Sd: Start Ao.LS: baud: Baud
B−2

D−2

E−2

Decimal Point delay time for Analogue Low rate

A−1

of PV Relay Output versus 1200 2400

0~0.0000 energized Low Scale 4800 9600
0:00.0~ -19999~+29999 19200 38400
9(m):59.9(s)
Lo.SC: Low rY1.Md: Relay Ao.HS: PritY: Parity
A−2

B−3

D−3

E−3

scale of PV 1 energized Analogue High n.Stb.1

-19999~+29999 mode Output versus n.Stb.2 odd
oFF Lo Hi High Scale EvEn
Lo.HLd Hi.HLd -19999~+29999
do
Hi.SC: High rY1.HY.: Relay Ao.Zro: Fine
A−3

B−4

D−4

scale of PV 1 Hysteresis Zero

-19999~+29999 0~5000counts Adjustment for
Analog Low
Output
-38011~+27524
Pv.Zro: Fine rY1.rd: Relay 1 Ao.SPn: Fine
A−4

B−5

D−5

Low point energized Span

Adjustment for delay time Adjustment for
PV display 0:00.0~ Analog High
-19999~+29999 9(m):59.9(s) Output
-38011~+27524
Pv.SPn: Fine rY1.Fd: Relay Z.S.CLr: Zero
A−5

B−6

D−6

High point 1 de-energized & Span Clear

Adjustment for delay time for Adjustment
PV display 0:00.0~ nonE Ao.Zro
-19999~+29999 9(m):59.9(s) Ao.SPn botH
Next Page

C1-01-6/7-2007-11-07
 Z.S.CLr: Clear
A−6

Fine Zero &

Span
Adjustment for

CS2-VA
PV display
nonE Pv.Zro
Pv.SPn botH
dSPLY:
A−7

Display
Function
Pv Mini.H

CSM- CSM-321S CSM-

MAx.H RS485
Lo.Cut: Low
A−8

Cut Function
-19999~+29999

AvG: Average
A−9

update for PV
1(None)~
99 times
M.AvG:
A−10

Moving
Average
update for PV
1(None)~
10 times
d.FiLt: Digital
A−11

filter
0(None)/1~99

CS1-PR
times
dn.KEY:
A−12

Down key
function
nonE rEL.Pv
Pv.HLd M.rSt

CSM-321S CSM- CSM-321S CSM- CSM-321S CSM-

rY.rSt
P.CodE: Pass
A−13

Code for enter

Programming
Level
0000~9999
F.LoCk:
A−14

Function Level
Lock
nonE USEr
EnG ALL

¾ Plesae refer to operating manual for detail description

C1-01-7/7-2007-11-07