kÉï=~ë=çÑW= NMKOMMT

loqelmelp=udmäìë=ap=L=`ÉéÜ
loqelmelp=ud=R=ap=L=`ÉéÜ
loqelmelp=ud=P=ap
j~áåíÉå~åÅÉ=fåëíêìÅíáçåë=====
båÖäáëÜ

ORTHOPHOS XGPlus

Easypad

ORTHOPHOS XG 5 / 3

P1
Prog. S kV mA

T R

Multipad

sÉêëáçå=QKM
 Sirona Dental Systems GmbH
Maintenance Instructions ORTHOPHOS XG

General information

ATTENTION !

Proper shielding of room and operator

position is essential.
Since these requirements vary from state
to state it is the assembler's/installer's
responsibility that all local radiation
safety requirements are met.

kÉï=~ë=çÑW= NMKOMMT

Changes since the last version: 07.2005

Chapter or section page
12 Checking the laser ................................................. 45

59 38 373 D3352
2 D3352.103.01.04.02
Sirona Dental Systems GmbH
Maintenance Instructions ORTHOPHOS XG

Contents
1 General ................................................................................................................................ 5

2 Visual Check ....................................................................................................................... 6

3 Indicator Lights and audible Signal.................................................................................. 7

4 Power supply adequacy..................................................................................................... 9

5 kV – verification, kV ramp during panoramic exposure ............................................... 10

6 Tube Current Verification ................................................................................................ 14

7 Exposure Time Verification ............................................................................................. 17

båÖäáëÜ
8 Checking the X-Ray Beam ............................................................................................... 20
8.1 Diaphragm/system adjustment menu ..................................................... 20

9 Checking the X-Ray Beam for panorama exposure ...................................................... 22

9.1 Preparing the Pan adjustment ................................................................ 22
9.2 Checking the pan sensor adjustment ..................................................... 23
9.3 Checking the pan diaphragm adjustment ............................................... 25
9.4 Checking the pan filter adjustment ......................................................... 27
9.5 Checking the pan symmetry ................................................................... 29
9.6 Checking the TSA sensor (full version only)........................................... 31

10 Checking the X-Ray Beam for cephalometer exposure................................................ 33

10.1 Preparing the Ceph adjustment .............................................................. 33
10.2 Checking the Ceph primary diaphragm adjustment................................ 34
10.3 Checking the ceph rotation fixpoint adjustment ...................................... 37
10.4 Checking the ceph main X-ray beam direction adjustment .................... 39

11 Checking the alignment of the ear plugs ....................................................................... 41

11.1 Preparing the ear olives.......................................................................... 41
11.2 Checking the ear plug alignment ............................................................ 42

12 Checking the laser............................................................................................................ 45

59 38 373 D3352
D3352.103.01.04.02 3
 Sirona Dental Systems GmbH
Maintenance Instructions ORTHOPHOS XG

59 38 373 D3352
4 D3352.103.01.04.02
Sirona Dental Systems GmbH 1 General
Maintenance Instructions ORTHOPHOS XG

1 General
To stay in compliance with the DHHS requirements the
Power Supply Adequacy
ORTHOPHOS XG must be maintained annually following
date of installation. To assure that the ORTHOPHOS XG system performance
It is the responsibility of the user to insure that the equip- is in accordance with Sirona specifications, an adequate
ment is maintained with the manufacturer's recommended power supply for permanently installation is essential.
Maintenance Instructions to insure compliance with the The Federal Performance Standard for diagnostic X-ray
Federal Performance Standard. units, code of Federal Regulations, Title 21 CFR, Subchap-
The manufacturer and the assembler/installer are relieved ter J, mandates an adequate power supply.
from responsibility in those cases where noncompliance
with the standard results from the user's failure to have the
manufacturer's recommended maintenance performed.
The actual maintenance inspection and consequent ser-
vice must be accomplished by a trained serviceman. Nei-
ther the inspection nor service is part of the equipment war-
ranty. Duty Cycle
Between exposures maintain at least a cool-off time (auto-
Technical instructions required matic exposure blockage, see Operating Instructions man-

båÖäáëÜ
Operating Instructions ual).
Service Manual
Operating Instructions
Instruments and adjustment tools required During measurements and controls it is necessary to ener-
All measuring devices must be suitable for measurements gize or de-energize the unit. For all operating steps please
on the mains potential. refer to the Operating Instructions manual.
This includes the pulse counter.
This means: A voltage of 1000 V between a connection and CAUTION with PC Boards!
ground must be possible. All PC boards are fitted with electronic components sensi-
tive to electrostatic discharge (ESD). In an environment of
1. Digital multimeter Fluke 87 III or equivalent. moving people electrostatic charges are unavoidable due to
Accuracy: friction caused by clothing, carpeting etc.
DC voltage ± 0.1 % of reading plus 0.02% of range
DC current ± 0.4 % of reading plus 0.1% of range. ATTENTION
To prevent damage of electronic chips do not touch same.
Always handle circuit boards by their edges.

ATTENTION
Electrical Shock Hazard!
2. Electromechanical pulse counter, model KESSLER Always turn unit OFF before connecting and disconnecting
ELLIS KT 203 ±1 pulse, or equivalent.. the test leads to the test points

ON
OFF
3. Adjustment set with alignment tool for X-ray beam , test
block and needle phantom delivered with the unit, (cus-
tomer's property).
WARNING
Life-threatening voltage on DX6.
ATTENTION
RADIATION!
Observe the radiation protection guide lines as outlined in
the Operating Instructions manual.
X-radiation is emitted as long as the release button is de-
pressed.
The X-ray indicator must light up on the Easypad during ra-
diation. An acoustic signal must also be heard.

59 38 373 D3352
D3352.103.01.04.02 5
2 Visual Check Sirona Dental Systems GmbH
Maintenance Instructions ORTHOPHOS XG

2 Visual Check

SIDEXIS
Software
Logiciel

• Look for mechanical damage possibly affecting radia-

tion safety.
• Verify that all labels are affixed and legible.
Defaced labels must be replaced.
Order same from Sirona (address, see rear)
in writing stating:

• Customer Name
• Customer Address

All Model Numbers with Serial Numbers still legible on the

unit for identification purposes. For serial numbers see also
Installation Report/Warranty Passport.

59 38 373 D3352
6 D3352.103.01.04.02
Sirona Dental Systems GmbH 3 Indicator Lights and audible Signal
Maintenance Instructions ORTHOPHOS XG

3 Indicator Lights and audible Signal

Radiation indicator Unit ON LED

XGPlus

ON
OFF

Radiation indicator Unit ON LED

båÖäáëÜ
Remote

P1
Prog. S kV mA XG 5 / 3

T R

• Unit ON LED:
Depress the main switch into the ”I” position to turn unit
ON.
The unit adjusts itself automatically, wait about
1 minute.
The ”Unit ON LED” in the upper right corner of the user
interface will then indicate that the unit is ON.

• Testing the keys and the functions on the user in-

terface.
– When the height adjustment is made the loud-
speaker should hum.
– If the forehead support functions correctly, the max.
holding torque is still present.
– If remote is installed, test the remote keys and dis-
play in addition.
– The release button must not be defective or broken.

See also Operating Instructions under ”Preparing the Expo-

sure” subchapter ”Switching the system on”.

59 38 373 D3352
D3352.103.01.04.02 7
3 Indicator Lights and audible Signal Sirona Dental Systems GmbH
Maintenance Instructions ORTHOPHOS XG

CAUTION RADIATION !
Observe Radiation Protection Guide Lines
see Operating Instructions

Radiation indicator Unit ON LED Radiation indicator Unit ON LED

menu
keys

sub-
P1 menukey
Prog. S kV mA
s

T R

Return key R Return key R – + keys Submenu

Orthophos XG 5 / 3 Orthophos XGPlus

• Make a exposure: • Interrupt an exposure – deadman feature:

– X-ray head must be in the initial position (If not, – Observe a cool-off time of max. 5 mins. between
press return key R). exposures (automatic exposure blockage).
– Establish exposure readiness via SIDEXIS. – Setting same as above.
For more details and possible error messages see
Operating Instructions. CAUTION RADIATION
– Set the P1 exposure program using the menu keys – Depress the release button until X-ray lights up and
(XG 5 / 3) or – + keys (XGPlus). subsequently release – the exposure must
– Select 68kV/8mA using submenu keys (XG 5 / 3) terminate immediately. The radiation indicator
or submenu – + keys (XGPlus). lights up.

ATTENTION
CAUTION RADIATION Defective light indicators constitute a safety hazard to the
– Depress the exposure button and hold until the patient as well as to the operator.
exposure terminates automatically. The user is not permitted to use the unit, until repairs
– The exposure ends when the rotation and radiation are made!
automatically switch off.
– The radiation indication must light up during the
exposure period.
– Simultaneously an audible beep must sound at the
unit.

59 38 373 D3352
8 D3352.103.01.04.02
Sirona Dental Systems GmbH 4 Power supply adequacy
Maintenance Instructions ORTHOPHOS XG

4 Power supply adequacy

1. 2.

300 VAC

3.

K1

båÖäáëÜ
n

*o *o

4. - 5.
K1

• To determine power supply adequacy, the line volt- Line voltage, no load: Max. permissible line voltage
age drop during exposure must be measured. drop:
1. Be sure power is disconnected at the central distribu- 180 – 208V 9V
tion panel!
208 – 230V 8V
• Remove front cover (for details see Service Manual).
230 – 240V 7.5V
2. Select 300VAC line voltage range on multimeter .
Connect measuring leads to terminal K1, L and N. 240 – 264V 7V
3. Connect power and switch unit ON n.
Wait 1 min. for self-adjustment of the unit. Record reading.
Press key R o to return X-ray tube head into the initial • Turn unit OFF.
position.
• Remove meter leads and refit cover.
4. Establish exposure readiness via SIDEXIS.
5. Select highest exposure level e.g. 90kV/12mA.
i NOTE
If the voltage drop is not within the specified range ad-
CAUTION RADIATION vise the customer, that an adequate power supply must be
installed. Refer to Pre-Installation Instructions.
– Depress the exposure key until meter reading is Disconnect unit and do not release for use!
obtained.

59 38 373 D3352
D3352.103.01.04.02 9
5 kV – verification, kV ramp during panoramic exposure Sirona Dental Systems GmbH
Maintenance Instructions ORTHOPHOS XG

5 kV – verification, kV ramp during panoramic

exposure

1. 2.
A

WARNING i NOTE
The electronics of the X-ray tube assembly are always Measurements:
connected to line voltage. 62kV correspond to 3.1V, permissible tolerance +/-10%

Always switch the X-ray unit off and wait until V203 is
no longer illuminated before contacting the test leads. i NOTE
During exposure the kV is increased in the central region
depending on kV/mA selected by up to 10%. This increase
can be measured in VDC.
WARNING
The test leads and measuring instruments used must 1. Remove cover (for details see Service Manual).
have a dielectric strength of at least 1000V!
2. Loosen the four screws A and remove cover plate B of
Be sure to use a battery-powered measuring instru- the electronics box.
ment with shock-hazard-protected sockets.

Use only test leads with shock protection.

ATTENTION
The X-ray tube assembly moves during the measurement.
Therefore, be sure to use test leads of sufficient length and
place the measuring instrument in a location where it is firm-
ly seated so that it doesn’t fall down.

59 38 373 D3352
10 D3352.103.01.04.02
Sirona Dental Systems GmbH 5 kV – verification, kV ramp during panoramic exposure
Maintenance Instructions ORTHOPHOS XG

3. 20VDC
4.
D

com. C

båÖäáëÜ
KV– KV+

5.
6. - 7.

400 VDC n

*
PC-board DX6

o XGPlus * o XG 5 / 3

3. Connect digital voltmeter to KV+ and KV– test points on Measurement:

PC board DX6 and select range 20 VDC.
4. Refit cover C and tighten screw D securely.
CAUTION RADIATION
– Depress the exposure key until the exposure
5. Switch unit ON n. terminates automatically.
Wait 1 min. for self-adjustment of the unit.
Press key R o to return X-ray tube head into the initial The following values must be obtained
position. (see also diagram on next page)
6. Establish exposure readiness via SIDEXIS. • up to 5.25 seconds: 3.1 V ±0.3V
• from 6.25 to 7.85 s KV-ramp: e.g. 4 V ±0.4V
7. Select P1 program and 62kV/8mA.
• after 8.85 seconds: 3 V ±0.3V

i NOTE
If specified values cannot be obtained, see Service Man-
ual, ”Radiograph Density in Central Region Incorrect”

59 38 373 D3352
D3352.103.01.04.02 11
5 kV – verification, kV ramp during panoramic exposure Sirona Dental Systems GmbH
Maintenance Instructions ORTHOPHOS XG

kV – Verification, kV–ramp during panoramic exposure

VDC

9 7.05s 14.1s
8 Complete P1
exposure
7 time

6 ramp
5 1.6s
ramp
max. 4.05V Nominal 4.0V
4
max. 3.41V min. 3.45V
Nominal 3.1V
3 min. 2.79V
6.25s 7.85s
2
5.25s 8.85s
1

0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 s
Exposure time

kV ramp diagram
with program P1 and 62kV/8mA set on the Easypad
(XGPlus) or Multipad (XG 5 / 3) and temple support fully
open.

59 38 373 D3352
12 D3352.103.01.04.02
Sirona Dental Systems GmbH 5 kV – verification, kV ramp during panoramic exposure
Maintenance Instructions ORTHOPHOS XG

8.

båÖäáëÜ
• Turn unit OFF.
8. Remove top cover and meter leads.

59 38 373 D3352
D3352.103.01.04.02 13
6 Tube Current Verification Sirona Dental Systems GmbH
Maintenance Instructions ORTHOPHOS XG

6 Tube Current Verification

WARNING
The electronics of the X-ray tube assembly are always
connected to line voltage.

Always switch the X-ray unit off and wait until V203 is
no longer illuminated before contacting the test leads.

WARNING
The test leads and measuring instruments used must
have a dielectric strength of at least 1000V!

Be sure to use a battery-powered measuring instru-

ment with shock-hazard-protected sockets.

Use only test leads with shock protection.

WARNING
Be sure to switch the X-ray unit off before removing the
jumper for the mA measuring jack.

59 38 373 D3352
14 D3352.103.01.04.02
Sirona Dental Systems GmbH 6 Tube Current Verification
Maintenance Instructions ORTHOPHOS XG

1. 20VDC 2.
D

com. C

båÖäáëÜ
MA+ MA–

3.
400 VDC 4. - 5.
A
n
·

PC-board DX6
* o XGPlus * o XG 5 / 3

1. Remove jumper A from MA+/MA – test points on PC Measurement:

board DX6. Connect digital ammeter to MA+ and MA–
and select range 20 mADC. CAUTION RADIATION
– Depress the exposure key and hold depressed until
2. Reattach cover C and tighten screw D securely.
meter reading is obtained.
3. Switch unit ON n.
Wait 1 min. for self-adjustment of the unit. The ammeter shall indicate 8mA ±1.6mA.
Press key R o to return X-ray tube head into the initial Record reading.
position.
i NOTE
4. Select 66kV/8mA. Establish exposure readiness via Readings: 1mA corresponds to a tube current of 1mA, per-
SIDEXIS. missible tolerance +/-20%.
5. If P1 program and 66kV/8mA are selected .
The unit must be ready for radiation.
i NOTE
If specified values cannot be obtained, see Service Man-
ual, chapter ”Tube Current Verification”.

59 38 373 D3352
D3352.103.01.04.02 15
6 Tube Current Verification Sirona Dental Systems GmbH
Maintenance Instructions ORTHOPHOS XG

6.

• If specified value is obtained switch unit OFF.

6. Remove upper cover and meter leads
• Replace jumper!

59 38 373 D3352
16 D3352.103.01.04.02
Sirona Dental Systems GmbH 7 Exposure Time Verification
Maintenance Instructions ORTHOPHOS XG

7 Exposure Time Verification

1. Pulse counter 2.
D

to N
to L
of 110VAC/60Hz
power receptacle
C

T1 T2

båÖäáëÜ
400 VDC

PC board DX6

1. Connect...
WARNING
The electronics of the X-ray tube assembly are always – test point T2 of terminal on PC board DX6 to L of
connected to line voltage. 110V power receptacle
– the common lead of the pulse counter to N of the
Always switch the X-ray unit off and wait until V203 is 110V power receptacle
no longer illuminated before contacting the test leads. – the second measuring lead of the pulse counter to
test point T1
2. Refit cover C and tighten screw D securely.
WARNING
The test leads and measuring instruments used must
have a dielectric strength of at least 1000V!

Be sure to use a battery-powered measuring instru-

ment with shock-hazard-protected sockets.

Use only test leads with shock protection.

59 38 373 D3352
D3352.103.01.04.02 17
7 Exposure Time Verification Sirona Dental Systems GmbH
Maintenance Instructions ORTHOPHOS XG

3. 6.
4. - 5.
n

* o XGPlus * o XG 5 / 3

3. Switch unit ON n.
Wait 1 min. for self-adjustment of the unit.
Press key R o to return X-ray tube head to the initial po-
sition.
4. Select 66kV/8mA.
Establish exposure readiness via SIDEXIS.

Measurement:

CAUTION RADIATION
– Depress the exposure key and hold depressed until
the exposure terminates automatically.

5. Select service routine S2 (Selecting a service routine:

See Service Manual):
• Set radiation time to 1 sec.
• Measured values at 50 Hz 50 pulses +/-10%
• Measured values at 60 Hz 60 pulses +/-10%

Record average pulse count.

i NOTE
If specified value cannot be obtained, see Service Man-
ual, chapter ”Exposure Time Verification”.

• If specified value is obtained, switch unit OFF.

6. Remove upper cover and meter leads.

59 38 373 D3352
18 D3352.103.01.04.02
Sirona Dental Systems GmbH 7 Exposure Time Verification
Maintenance Instructions ORTHOPHOS XG

7. 8.

båÖäáëÜ
7. Screw the cover plate back on to the electronics box.
8. Reattach the housing covers.

59 38 373 D3352
D3352.103.01.04.02 19
8 Checking the X-Ray Beam Sirona Dental Systems GmbH
8.1 Diaphragm/system adjustment menu Maintenance Instructions ORTHOPHOS XG

8 Checking the X-Ray Beam

1.

2. 3.
XGPlus XG 5

SERVICE

i NOTE
8.1 Diaphragm/system adjustment menu When you open the DIAPHRAGM/SYSTEM ADJUSTMENT
menu, the unit switches from the user mode to the PC ser-
The DIAPHRAGM/SYSTEM ADJUSTMENT menu guides vice mode logged by the PC.
you through the adjustment of the panoramic unit and the
cephalometer. This service routine is started from SIDEXIS ORTHOPHOS XGPlus DS / Ceph:
XG: This mode is indicated by the PC service screen (2.) dis-
EXTRAS Æ CONSTANCY TEST Æ XCXP Æ SELECT X-RAY played on the Easypad. In PC service mode, the Easypad
DEVICE Æ SERVICE EXPOSURE Æ DIAPHRAGM/SYSTEM control options are determined by SIDEXIS and the current-
ADJUSTMENT ly selected service routine. General control of the unit by
means of the Easypad (as in the user mode) is not possible
i NOTE in this mode.
The DIAPHRAGM/SYSTEM ADJUSTMENT menu is pass- ORTHOPHOS XG 5 DS / Ceph, ORTHOPHOS XG 3 DS.
word-protected. As password, enter the first four digits of This mode is indicated by the message SERVICE (3.) on
the current system date (PC) in reverse order. the Multipad. In PC service mode, the Multipad control op-
tions are determined by SIDEXIS and the currently selected
Example: On 05/30/2004, the service password is 5003 service routine. General control of the unit by means of the
Multipad (as in the user mode) is not possible in this mode.

59 38 373 D3352
20 D3352.103.01.04.02
Sirona Dental Systems GmbH 8 Checking the X-Ray Beam
Maintenance Instructions ORTHOPHOS XG 8.1 Diaphragm/system adjustment menu

The DIAPHRAGM/SYSTEM ADJUSTMENT menu has

11 submenus:

z Pan - Sensor adjustment

z Pan - Diaphragm
z Pan - Filter
z Pan - Symmetry
z Ceph - Primary diaphragm
z Ceph - Fixed point of rotation
z Ceph - Main X-ray beam direction
z Ceph -Quickshot (full version only)
z TSA - Sensor (full version only)
z Pan - Reset adjustment

båÖäáëÜ
z Ceph - Reset adjustment
z Sirona Service Sheet (internal SIRONA information)

You can change between the individual submenus by click-

ing the tabs with the mouse. To quit the DIAPHRAGM/
SYSTEM ADJUSTMENT menu, click CANCEL.

59 38 373 D3352
D3352.103.01.04.02 21
9 Checking the X-Ray Beam for panorama exposure Sirona Dental Systems GmbH
9.1 Preparing the Pan adjustment Maintenance Instructions ORTHOPHOS XG

9 Checking the X-Ray Beam for panorama exposure

1. 2. Needles on
top side

9.1 Preparing the Pan adjustment

In order to perform the PAN sensor adjustment and the
symmetry adjustment you must insert needle phantom A
in the bite block holder of the panoramic X-ray unit.
The needle phantom must be removed from the bite block
holder for the pan diaphragm adjustment.

ATTENTION
It is essential that the needle phantom is removed from bite
block holder of the panoramic X-ray unit again before a
Ceph exposure is taken; otherwise the phantom may collide
with the sensor.

i NOTE
When fitting the needle phantom, make sure that it is
correctly oriented. For the adjustment of the X-ray unit, the
phantom must be fitted in such a way that the needles
point upward (2.).

59 38 373 D3352
22 D3352.103.01.04.02
Sirona Dental Systems GmbH 9 Checking the X-Ray Beam for panorama exposure
Maintenance Instructions ORTHOPHOS XG 9.2 Checking the pan sensor adjustment

1. in SIDEXIS

2.

båÖäáëÜ
on the Multipad (XG 5 / 3) on the touchscreen (XGPlus)

E X RAY
1 - 60 kV/3 mA + S10

60/3 0.60 2 0.6 s 1

9.2 Checking the pan sensor adjustment Orthophos XG 5 / 3:

The exposure dialog box showing the exposure status
• Plug the sensor into the sensor slot on the panoramic
appears in Sidexis.
X-ray unit.
The initialization status is visualized by a progress indi-
• Insert the needle phantom in the bite block holder of the
cator on the Multipad.
panoramic X-ray unit (see page 22).
The initialization procedure is completed when the ex-
1. Open the PAN - SENSOR ADJUSTMENT submenu. posure parameters of service routine S010.1
(60 kV/3 mA; 0.6 s) are displayed and the progress in-
i NOTE dicator disappears.
The menu provides a precision adjustment and a coarse ad-
justment (precision adjustment is preset). Perform a preci- Orthophos XGPlus:
sion adjustment first. In most cases, previous coarse adjust-
The exposure dialog box showing the exposure status
ment is not necessary.
appears in Sidexis.
2. Make SIDEXIS XG ready for exposure: Service routine S010.1 is displayed on the Easypad
Click IMAGE ACQUISITION. touchscreen.

59 38 373 D3352
D3352.103.01.04.02 23
9 Checking the X-Ray Beam for panorama exposure Sirona Dental Systems GmbH
9.2 Checking the pan sensor adjustment Maintenance Instructions ORTHOPHOS XG

3. 4.

Prog. S kV mA

T R

G
T R

G XGPlus XG 5 / 3

Adjustment: ok

i NOTE
3. Take an exposure (60 kV/3 mA): If the criteria specified above are not fulfilled, the sensor
– Press the R key to move the unit back to the must be adjusted. The procedure for adjusting the unit is de-
starting position. scribed in the service manual.
– Press the release button. Hold down the release
button until image acquisition is completed and the
preview image appears in the exposure dialog box.

4. Evaluate the exposed image:

– The three needle images must lie in the center
of the exposed areas and inside the auxiliary
lines (see image 4.).

59 38 373 D3352
24 D3352.103.01.04.02
Sirona Dental Systems GmbH 9 Checking the X-Ray Beam for panorama exposure
Maintenance Instructions ORTHOPHOS XG 9.3 Checking the pan diaphragm adjustment

1. ORTHOPHOS
ORTHOPHOS XG Plus
DS / Ceph,
XG 5 DS / Ceph
in SIDEXIS

2.

båÖäáëÜ
on the Multipad (XG 5) on the touchscreen (XGPlus)

E X RAY
1 - 60 kV/3 mA + S30

60/3 0.20 2 0.20 s 2

9.3 Checking the pan diaphragm

adjustment Orthophos XG 5 / 3:
The exposure dialog box showing the exposure status
• Remove the needle phantom from the bite block holder appears in Sidexis.
of the panoramic X-ray unit.
The initialization status is visualized by a progress indi-
1. Change to the PAN - DIAPHRAGM submenu. cator on the Multipad.
i NOTE The initialization procedure is completed when the ex-
posure parameters of service routine S030.2
For XGPlus, XG 5 (60 kV/3 mA; 0.6 s) are displayed and the progress in-
The menu provides a precision adjustment and a dicator disappears.
coarse adjustment. Always try to use precision adjust-
ment first when adjusting the unit. In most cases, it is Orthophos XGPlus:
not necessary to perform a coarse adjustment prior to
The exposure dialog box showing the exposure status
precision adjustment.
appears in Sidexis.

2. Make SIDEXIS XG ready for exposure: Service routine S030.2 is displayed on the Easypad
Click IMAGE ACQUISITION. touchscreen.

59 38 373 D3352
D3352.103.01.04.02 25
9 Checking the X-Ray Beam for panorama exposure Sirona Dental Systems GmbH
9.3 Checking the pan diaphragm adjustment Maintenance Instructions ORTHOPHOS XG

3. 4.

Prog. S kV mA

T R

G
T R

G XGPlus XG 5 / 3

Adjustment: ok
– A white border surrounding the image on all
sides must be visible. The maximum density
3. Take an exposure (60 kV/3 mA):
must lie in the center of the diaphragm area.
– Press the R key to move the unit back to the
starting position. i NOTE
– Press the release button. Hold down the release If the current image differs from the ideal image (see image
button until image acquisition is completed and the 4.), the diaphragm must be adjusted. The procedure for ad-
preview image appears in the exposure dialog box. justing the unit is described in the service manual.

4. Evaluate the exposed image:

– The exposed diaphragm area must lie horizon-
tally centered in the image field as well as
inside the superimposed auxiliary lines.

59 38 373 D3352
26 D3352.103.01.04.02
Sirona Dental Systems GmbH 9 Checking the X-Ray Beam for panorama exposure
Maintenance Instructions ORTHOPHOS XG 9.4 Checking the pan filter adjustment

1. in SIDEXIS

2.

båÖäáëÜ
on the Multipad (XG 5) on the touchscreen (XGPlus)

E X RAY
1 - 60 kV/3 mA + S30

60/3 0.20 2 0.20 s 3

9.4 Checking the pan filter adjustment

Orthophos XGPlus:
Not necessary for ORTHOPHOS XG 3 DS
The exposure dialog box showing the exposure status
1. Change to the PAN - FILTER submenu. appears in Sidexis.
2. Make SIDEXIS XG ready for exposure: Service routine S030.3 is displayed on the Easypad
Click IMAGE ACQUISITION. touchscreen.

Orthophos XG 5:
The exposure dialog box showing the exposure status
appears in Sidexis.
The initialization status is visualized by a progress indi-
cator on the Multipad.
The initialization procedure is completed when the ex-
posure parameters of service routine S030.3
(60 kV/3 mA; 0.6 s) are displayed and the progress in-
dicator disappears.

59 38 373 D3352
D3352.103.01.04.02 27
9 Checking the X-Ray Beam for panorama exposure Sirona Dental Systems GmbH
9.4 Checking the pan filter adjustment Maintenance Instructions ORTHOPHOS XG

3. 4.

Prog. S kV mA

T R

G
T R

G XGPlus XG 5

Adjustment: ok

i NOTE
3. Take an exposure (60 kV/3 mA): If the current image differs from the ideal image (see image
– Press the R key to move the unit back to the 4.), the diaphragm must be adjusted. The procedure for ad-
starting position. justing the unit is described in the service manual.
– Press the release button. Hold down the release
button until image acquisition is completed and the
preview image appears in the exposure dialog box.

4. Evaluate the exposed image:

– The superimposed filter must cover one half of
the diaphragm (see image 4.).

59 38 373 D3352
28 D3352.103.01.04.02
Sirona Dental Systems GmbH 9 Checking the X-Ray Beam for panorama exposure
Maintenance Instructions ORTHOPHOS XG 9.5 Checking the pan symmetry

1. in SIDEXIS

2.

båÖäáëÜ
on the Multipad (XG 5 / 3) on the touchscreen (XGPlus)

E X RAY
1 - 60 kV/3 mA + S10

60/3 14.1 2 14.1 s 2

9.5 Checking the pan symmetry Orthophos XG 5 / 3:

The exposure dialog box showing the exposure status
• Insert the needle phantom in the bite block holder of the appears in Sidexis.
panoramic X-ray unit (see page 22).
The initialization status is visualized by a progress indi-
1. Change to the PAN - SYMMETRY submenu. cator on the Multipad.
The initialization procedure is completed when the ex-
2. Make SIDEXIS XG ready for exposure:
Click IMAGE ACQUISITION. posure parameters of service routine S010.2
(60 kV/3 mA; 0.6 s) are displayed and the progress in-
dicator disappears.

Orthophos XGPlus:
The exposure dialog box showing the exposure status
appears in Sidexis.
Service routine S010.2 is displayed on the Easypad
touchscreen.

59 38 373 D3352
D3352.103.01.04.02 29
9 Checking the X-Ray Beam for panorama exposure Sirona Dental Systems GmbH
9.5 Checking the pan symmetry Maintenance Instructions ORTHOPHOS XG

3.

Prog. S kV mA

T R

G
T R

G XGPlus XG 5 / 3

4.

ZOOM: 1:1

± 0.75 mm ± 0.75 mm

A1 = 88.6 mm ± 1 mm

A2 A2
A2 = 44.3 ± 0.5 mm A2 = 44.3 ± 0.5 mm

Adjustment: ok

3. Take an exposure (60 kV/3 mA):

– Press the R key to move the unit back to the - Distance A1 must be 88.6 ± 1 mm.
starting position. - Distances A2 must be identical, each being
– Press the release button. Hold down the release 44.3 ± 0.5 mm.
button until image acquisition is completed and the - A white border surrounding the image on all
preview image appears in the exposure dialog box. sides must be visible (when zoomed out fully).
4. Evaluate the captured image.
- The shadow of the center needle, the needle im-
i NOTE
If these criteria are not fulfilled, the symmetry must be ad-
age and the auxiliary line must be congruent and
justed. The procedure for adjusting the unit is described in
located behind each other. the service manual.
A tolerance (offset of needle from the central
auxiliary line) of ± 0.75 mm is admissible.

59 38 373 D3352
30 D3352.103.01.04.02
Sirona Dental Systems GmbH 9 Checking the X-Ray Beam for panorama exposure
Maintenance Instructions ORTHOPHOS XG 9.6 Checking the TSA sensor (full version only)

1. in SIDEXIS

2.

båÖäáëÜ
3. on the touchscreen

E X RAY
1 - 60 kV/3 mA + S30

2 0.20 s 4

T R

G ?

9.6 Checking the TSA sensor (full version only) 3. Take an exposure (60 kV/3 mA):
– Press the R key on the Easypad to move the unit
1. Change to the TSA - SENSOR submenu.
back to the starting position.
2. Make SIDEXIS XG ready for exposure: The procedure is completed when the status message
Click IMAGE ACQUISITION “ORTHOPHOS is ready for exposure“ appears on the
The exposure dialog box showing the exposure status touchscreen.
appears in Sidexis. – Press the release button. Hold down the release
Service routine S030.4 is displayed on the Easypad button until image acquisition is completed and the
touchscreen. preview image appears in the exposure dialog box.

59 38 373 D3352
D3352.103.01.04.02 31
9 Checking the X-Ray Beam for panorama exposure Sirona Dental Systems GmbH
9.6 Checking the TSA sensor (full version only) Maintenance Instructions ORTHOPHOS XG

4.

Adjustment: ok

4. Evaluate the X-ray image:

– The exposed diaphragm area must lie horizon-
tally centered in the image field.
– A white border surrounding the image on all
sides must be visible. The maximum density
must lie in the center of the diaphragm area.

i NOTE
If these criteria are not fulfilled, the symmetry must be ad-
justed. The procedure for adjusting the unit is described in
the service manual.

59 38 373 D3352
32 D3352.103.01.04.02
Sirona Dental Systems GmbH 10 Checking the X-Ray Beam for cephalometer exposure
Maintenance Instructions ORTHOPHOS XG 10.1 Preparing the Ceph adjustment

10 Checking the X-Ray Beam for cephalometer

exposure
1.

båÖäáëÜ
10.1 Preparing the Ceph adjustment
You must insert test phantom B in the sensor slot on the
panoramic X-ray unit in order to perform the adjustment
of the ceph primary diaphragm and the adjustment of
the ceph main X-ray beam direction.
The test phantom must be removed from the sensor slot on
the panoramic X-ray unit for the adjustment of the ceph
fixed point of rotation and for the ceph quickshot.

59 38 373 D3352
D3352.103.01.04.02 33
10 Checking the X-Ray Beam for cephalometer exposure Sirona Dental Systems GmbH
10.2 Checking the Ceph primary diaphragm adjustment Maintenance Instructions ORTHOPHOS XG

1. in SIDEXIS

2.

on the Multipad (XG 5) on the touchscreen (XGPlus)

E X RAY
1 - 80 kV/14 mA + S10

80/14 14.9 2 14.9 s 3

10.2 Checking the Ceph primary diaphragm Orthophos XG 5:

adjustment The exposure dialog box showing the exposure status
appears in Sidexis.
• Move the ear plug holders on the cephalometer The initialization status is visualized by a progress indi-
completely apart and swing them out of the beam direc- cator on the Multipad.
tion (ap).
The initialization procedure is completed when the ex-
• Insert the test phantom in the sensor slot on the pan- posure parameters of service routine S010.3
oramic X-ray unit (see page 33). (60 kV/3 mA; 0.6 s) are displayed and the progress in-
• Plug the sensor into the sensor slot on the cephalome- dicator disappears.
ter.
• Open the DIAPHRAGM/SYSTEM ADJUSTMENT Orthophos XGPlus:
menu. The exposure dialog box showing the exposure status
appears in Sidexis.
1. Select the CEPH - PRIMARY DIAPHRAGM submenu.
Service routine S010.3 is displayed on the Easypad
2. Make SIDEXIS XG ready for exposure: touchscreen.
Click IMAGE ACQUISITION.

59 38 373 D3352
34 D3352.103.01.04.02
Sirona Dental Systems GmbH 10 Checking the X-Ray Beam for cephalometer exposure
Maintenance Instructions ORTHOPHOS XG 10.2 Checking the Ceph primary diaphragm adjustment

3.

Prog. S kV mA

T R

G
T R

G XGPlus

båÖäáëÜ
XG 5

3. Take an exposure (80 kV/14 mA):

– Press the R key to move the unit back to the
starting position.
– Press the release button. Hold down the release
button until image acquisition is completed and the
preview image appears in the exposure dialog box.

59 38 373 D3352
D3352.103.01.04.02 35
10 Checking the X-Ray Beam for cephalometer exposure Sirona Dental Systems GmbH
10.2 Checking the Ceph primary diaphragm adjustment Maintenance Instructions ORTHOPHOS XG

4.

S2

S2

Adjustment: ok

S3 = approx. 60 mm

4. Evaluate the captured image.

i NOTE
– The vertical pin must be horizontally centered
If S3 is significantly larger than 60 mm, check whether light
in the exposed image area.
barrier V61_1 (LB on the horizontal diaphragm slider) is
properly installed. If necessary, correct the alignment of the – A uniform white border surrounding the image
light barrier and then repeat the entire pan and ceph adjust- on all sides must be visible.
ment procedure. – Distance S3 must be approx. 60 mm.

i NOTE
A slight vertical offset of the grid is permissible.
V61_1
(must be installed
vertically) i NOTE
If the image differs from the ideal image 4., the ceph primary
diaphragm must be readjusted. The procedure for adjusting
the unit is described in the service manual.

59 38 373 D3352
36 D3352.103.01.04.02
Sirona Dental Systems GmbH 10 Checking the X-Ray Beam for cephalometer exposure
Maintenance Instructions ORTHOPHOS XG 10.3 Checking the ceph rotation fixpoint adjustment

1. in SIDEXIS

2.

båÖäáëÜ
on the Multipad (XG 5) on the touchscreen (XGPlus)

E X RAY
1 - 80 kV/14 mA + S10

80/14 0.60 2 0.60 s 5

10.3 Checking the ceph rotation fixpoint Orthophos XG 5:

adjustment The exposure dialog box showing the exposure status
appears in Sidexis.
• Remove the ceph test phantom from the sensor slot of The initialization status is visualized by a progress indi-
the panoramic X-ray unit. cator on the Multipad.
1. Change to the CEPH - FIXED POINT OF ROTATION The initialization procedure is completed when the ex-
submenu. posure parameters of service routine S010.5
(60 kV/3 mA; 0.6 s) are displayed and the progress in-
i NOTE dicator disappears.
The menu provides a precision adjustment and a
coarse adjustment. Always try to use precision adjust- Orthophos XGPlus:
ment first when adjusting the unit. In most cases, it is
The exposure dialog box showing the exposure status
not necessary to perform a coarse adjustment prior to
appears in Sidexis.
precision adjustment.
Service routine S010.5 is displayed on the Easypad
2. Make SIDEXIS XG ready for exposure: touchscreen.
Click IMAGE ACQUISITION.

59 38 373 D3352
D3352.103.01.04.02 37
10 Checking the X-Ray Beam for cephalometer exposure Sirona Dental Systems GmbH
10.3 Checking the ceph rotation fixpoint adjustment Maintenance Instructions ORTHOPHOS XG

3. 4.

Prog. S kV mA

T R

G
T R

G XGPlus XG 5

Adjustment: ok

sides must be visible.

3. Take an exposure (80 kV/14 mA):
– Press the R key to move the unit back to the
starting position.
i NOTE
If the criteria specified above are not fulfilled, the ceph fixed
– Press the release button. Hold down the release point of rotation must be adjusted. The procedure for adjust-
button until image acquisition is completed and the ing the unit is described in the service manual.
preview image appears in the exposure dialog box.

4. Evaluate the exposed image:

– The exposed diaphragm area must lie centered
and straight in the image field as well as inside
the superimposed auxiliary lines (see image 4.).
– A white border surrounding the image on all

59 38 373 D3352
38 D3352.103.01.04.02
Sirona Dental Systems GmbH 10 Checking the X-Ray Beam for cephalometer exposure
Maintenance Instructions ORTHOPHOS XG 10.4 Checking the ceph main X-ray beam direction adjustment

1. in SIDEXIS

2.

båÖäáëÜ
on the Multipad (XG 5) on the touchscreen (XGPlus)

E X RAY
1 - 80 kV/14 mA + S10

80/14 14.9 2 14.9 s 6

10.4 Checking the ceph main X-ray beam Orthophos XG 5:

direction adjustment The exposure dialog box showing the exposure status
appears in Sidexis.
• Insert the test phantom in the sensor slot on the pan-
oramic X-ray unit (see page 33). The initialization status is visualized by a progress indi-
cator on the Multipad.
• Swing the ear plug holders out of the beam direction.
The initialization procedure is completed when the ex-
1. Change to the CEPH - MAIN X-RAY BEAM posure parameters of service routine S010.6
DIRECTION submenu. (60 kV/3 mA; 0.6 s) are displayed and the progress in-
dicator disappears.
2. Make SIDEXIS XG ready for exposure:
Click IMAGE ACQUISITION.
Orthophos XGPlus:
The exposure dialog box showing the exposure status
appears in Sidexis.
Service routine S010.6 is displayed on the Easypad
touchscreen.

59 38 373 D3352
D3352.103.01.04.02 39
10 Checking the X-Ray Beam for cephalometer exposure Sirona Dental Systems GmbH
10.4 Checking the ceph main X-ray beam direction adjustment Maintenance Instructions ORTHOPHOS XG

3.

Prog. S kV mA

T R

G
T R

G XGPlus XG 5

4.

10 mm

10 mm

10 mm

10 mm

Adjustment: ok

3. Take an exposure (80 kV/14 mA): 4. Evaluate the exposed image:

– Press the R key to move the unit back to the – A horizontal bar must be visible in the center of
starting position. the image (see image 4.). If this bar is visible,
– Press the release button. Hold down the release the exposure is OK and ...
button until image acquisition is completed and the – the two beams imaged are within the tolerance
preview image appears in the exposure dialog box. band of ± 10 mm (see image 4.).

i NOTE
If the criteria specified above are not fulfilled, the ceph main
X-ray beam direction must be adjusted. The procedure for
adjusting the unit is described in the service manual.

59 38 373 D3352
40 D3352.103.01.04.02
Sirona Dental Systems GmbH 11 Checking the alignment of the ear plugs
Maintenance Instructions ORTHOPHOS XG 11.1 Preparing the ear olives

11 Checking the alignment of the ear plugs

1. 2.

båÖäáëÜ
D

3.

11.1 Preparing the ear olives 1. Move the ear plug holders completely apart and swing
them into the beam direction.
i NOTE 2. Fit adjusting caps D onto the ear plugs and secure them
The sensor must be plugged into the sensor slot on the with adhesive tape.
cephalometer. No sensor may be plugged into the sensor Black adjusting cap on the outside (sensor side),
slot on the panoramic X-ray unit. Transparent adjusting cap on the inside (tube as-
sembly side).
• Select the CEPH mode on the Multipad (XG 5) or 3. Unscrew the cover from the cephalometer.
Easypad (XGPlus).

59 38 373 D3352
D3352.103.01.04.02 41
11 Checking the alignment of the ear plugs Sirona Dental Systems GmbH
11.2 Checking the ear plug alignment Maintenance Instructions ORTHOPHOS XG

1. 2. 4.

3.

11.2 Checking the ear plug alignment

1. In Sidexis XG, select the constancy test:
EXTRAS Æ CONSTANCY TEST
The typical SIDEXIS user interface is started. The con-
stancy test is preset.
2. Start the exposure mode:
Click XCXP
The dialog box for selecting the X-ray device appears
on the screen.
3. Select/confirm the X-ray device:
Select e.g. Room2 (Kammer2) and click OK
The dialog box for selecting the test type appears on
the screen.
4. Select/confirm the test type:
Click SERVICE EXPOSURE
The dialog box for selecting the service exposure ap-
pears on the screen.

59 38 373 D3352
42 D3352.103.01.04.02
Sirona Dental Systems GmbH 11 Checking the alignment of the ear plugs
Maintenance Instructions ORTHOPHOS XG 11.2 Checking the ear plug alignment

5.

båÖäáëÜ
i NOTE
The ceph mode must be activated on the Multipad (XG 5) or
Easypad (XGPlus) for the ceph quality test
exposure.

5. Select/confirm the service exposure:

Click QUALITY TEST EXPOSURE.

i NOTE
If necessary, select the X-ray component.

The exposure dialog box showing the exposure status

appears in Sidexis.

59 38 373 D3352
D3352.103.01.04.02 43
11 Checking the alignment of the ear plugs Sirona Dental Systems GmbH
11.2 Checking the ear plug alignment Maintenance Instructions ORTHOPHOS XG

6.

Prog. S kV mA

T R

G
T R

G XGPlus XG 5

6. Take an exposure (80 kV/14 mA):

– Press the R key to move the unit back to the
starting position.
– Press the release button. Hold down the release
button until image acquisition is completed and the
preview image appears in the exposure dialog box.

• The lead balls in the adjusting caps appear as dots

on the image. The two dots must be coincident.

i NOTE
If the criteria specified above is not fulfilled, the ear olives
must be adjusted. The procedure for adjusting the ear olives
is described in the service manual.

59 38 373 D3352
44 D3352.103.01.04.02
Sirona Dental Systems GmbH 12 Checking the laser
Maintenance Instructions ORTHOPHOS XG 11.2 Checking the ear plug alignment

12 Checking the laser

1.

Horizontal beam

båÖäáëÜ
Vertical beam
2.

A B
Label

1. Insert the forehead and temple supports. SAG laser (vertical line)
The light beam must strike the center of the head support
2. Check the laser:
in a vertical direction.
• Fasten a piece of white cardboard between the temple
supports. FH laser (horizontal line)
• Swivel the mirror by pressing the left recess A on the The light beam must strike the FH line of the sheet of card-
touch bar. board attached to the head support. It must be possible to
displace the light beam vertically using slide C. Unwanted
• Switch on the light localizer with key B on the Easy- movement of the FH light localizer is not permitted.
pad. The Lasers generate a red line.
i NOTE
WARNING To adjust the lasers, see Maintenance Instructions.
Class 1 radiation is emitted during installation. No controls are available to adjust the laser power.
Always keep eyes a minimum distance of 100mm
away from the laser. Do not stare into the beam.

59 38 373 D3352
D3352.103.01.04.02 45
12 Checking the laser Sirona Dental Systems GmbH
11.2 Checking the ear plug alignment Maintenance Instructions ORTHOPHOS XG

59 38 373 D3352
46 D3352.103.01.04.02
 loqelmelp=ud
Yearly Maintenance Checklist

Customer: _________________________ Address:_________________________

Dealer:____________________________ Address:_________________________

Date of original installation: ___________ Date of inspection: ________________

Report of Assembly FD 2579 # _________

____________________________________
_______
SCHEDULE Yes No Remarks

All manuals are present

Test instruments as required

Manufacturer Model Accuracy Last calibrated
Voltmeter
mAmeter
Pulse counter
Any mechanical damage noticed

All labels are present and legible

All indicator lights are OK

Radiation indicator X-ray lights up, audible buzzer OK

Deadman feature OK

Power supply adequate Line voltage: . . . . . . . . . .V

Voltage drop: . . . . . . . . . V
kV – Verification is OK

Tube current is within specified limits Measurement: . . . . . . . mA

Specified exposure time, (pulses) OK Pulse count: . . . . . . . . . . . . . .

X-ray beam position, panoramic OK

X-ray beam position, ceph OK

The unit is in compliance with MFG specified tests and safety

Technician: Dealer:
D3352.103.01.04.02 59 38 373 D3352
 loqelmelp=ud
Yearly Maintenance Checklist

Customer: _________________________ Address:_________________________

Dealer:____________________________ Address:_________________________

Date of original installation: ___________ Date of inspection: ________________

Report of Assembly FD 2579 # _________

____________________________________
_______
SCHEDULE Yes No Remarks

All manuals are present

Test instruments as required

Manufacturer Model Accuracy Last calibrated
Voltmeter
mAmeter
Pulse counter
Any mechanical damage noticed

All labels are present and legible

All indicator lights are OK

Radiation indicator X-ray lights up, audible buzzer OK

Deadman feature OK

Power supply adequate Line voltage: . . . . . . . . . .V

Voltage drop: . . . . . . . . . V
kV – Verification is OK

Tube current is within specified limits Measurement: . . . . . . . mA

Specified exposure time, (pulses) OK Pulse count: . . . . . . . . . . . . . .

X-ray beam position, panoramic OK

X-ray beam position, ceph OK

The unit is in compliance with MFG specified tests and safety

Technician: Dealer:
D3352.103.01.04.02 59 38 373 D3352
 loqelmelp=ud
Yearly Maintenance Checklist

Customer: _________________________ Address:_________________________

Dealer:____________________________ Address:_________________________

Date of original installation: ___________ Date of inspection: ________________

Report of Assembly FD 2579 # _________

____________________________________
_______
SCHEDULE Yes No Remarks

All manuals are present

Test instruments as required

Manufacturer Model Accuracy Last calibrated
Voltmeter
mAmeter
Pulse counter
Any mechanical damage noticed

All labels are present and legible

All indicator lights are OK

Radiation indicator X-ray lights up, audible buzzer OK

Deadman feature OK

Power supply adequate Line voltage: . . . . . . . . . .V

Voltage drop: . . . . . . . . . V
kV – Verification is OK

Tube current is within specified limits Measurement: . . . . . . . mA

Specified exposure time, (pulses) OK Pulse count: . . . . . . . . . . . . . .

X-ray beam position, panoramic OK

X-ray beam position, ceph OK

The unit is in compliance with MFG specified tests and safety

Technician: Dealer:
D3352.103.01.04.02 59 38 373 D3352
 loqelmelp=ud
Yearly Maintenance Checklist

Customer: _________________________ Address:_________________________

Dealer:____________________________ Address:_________________________

Date of original installation: ___________ Date of inspection: ________________

Report of Assembly FD 2579 # _________

____________________________________
_______
SCHEDULE Yes No Remarks

All manuals are present

Test instruments as required

Manufacturer Model Accuracy Last calibrated
Voltmeter
mAmeter
Pulse counter
Any mechanical damage noticed

All labels are present and legible

All indicator lights are OK

Radiation indicator X-ray lights up, audible buzzer OK

Deadman feature OK

Power supply adequate Line voltage: . . . . . . . . . .V

Voltage drop: . . . . . . . . . V
kV – Verification is OK

Tube current is within specified limits Measurement: . . . . . . . mA

Specified exposure time, (pulses) OK Pulse count: . . . . . . . . . . . . . .

X-ray beam position, panoramic OK

X-ray beam position, ceph OK

The unit is in compliance with MFG specified tests and safety

Technician: Dealer:
D3352.103.01.04.02 59 38 373 D3352
 loqelmelp=ud
Yearly Maintenance Checklist

Customer: _________________________ Address:_________________________

Dealer:____________________________ Address:_________________________

Date of original installation: ___________ Date of inspection: ________________

Report of Assembly FD 2579 # _________

____________________________________
_______
SCHEDULE Yes No Remarks

All manuals are present

Test instruments as required

Manufacturer Model Accuracy Last calibrated
Voltmeter
mAmeter
Pulse counter
Any mechanical damage noticed

All labels are present and legible

All indicator lights are OK

Radiation indicator X-ray lights up, audible buzzer OK

Deadman feature OK

Power supply adequate Line voltage: . . . . . . . . . .V

Voltage drop: . . . . . . . . . V
kV – Verification is OK

Tube current is within specified limits Measurement: . . . . . . . mA

Specified exposure time, (pulses) OK Pulse count: . . . . . . . . . . . . . .

X-ray beam position, panoramic OK

X-ray beam position, ceph OK

The unit is in compliance with MFG specified tests and safety

Technician: Dealer:
D3352.103.01.04.02 59 38 373 D3352
 loqelmelp=ud
Yearly Maintenance Checklist

Customer: _________________________ Address:_________________________

Dealer:____________________________ Address:_________________________

Date of original installation: ___________ Date of inspection: ________________

Report of Assembly FD 2579 # _________

____________________________________
_______
SCHEDULE Yes No Remarks

All manuals are present

Test instruments as required

Manufacturer Model Accuracy Last calibrated
Voltmeter
mAmeter
Pulse counter
Any mechanical damage noticed

All labels are present and legible

All indicator lights are OK

Radiation indicator X-ray lights up, audible buzzer OK

Deadman feature OK

Power supply adequate Line voltage: . . . . . . . . . .V

Voltage drop: . . . . . . . . . V
kV – Verification is OK

Tube current is within specified limits Measurement: . . . . . . . mA

Specified exposure time, (pulses) OK Pulse count: . . . . . . . . . . . . . .

X-ray beam position, panoramic OK

X-ray beam position, ceph OK

The unit is in compliance with MFG specified tests and safety

Technician: Dealer:
D3352.103.01.04.02 59 38 373 D3352
 loqelmelp=ud
Yearly Maintenance Checklist

Customer: _________________________ Address:_________________________

Dealer:____________________________ Address:_________________________

Date of original installation: ___________ Date of inspection: ________________

Report of Assembly FD 2579 # _________

____________________________________
_______
SCHEDULE Yes No Remarks

All manuals are present

Test instruments as required

Manufacturer Model Accuracy Last calibrated
Voltmeter
mAmeter
Pulse counter
Any mechanical damage noticed

All labels are present and legible

All indicator lights are OK

Radiation indicator X-ray lights up, audible buzzer OK

Deadman feature OK

Power supply adequate Line voltage: . . . . . . . . . .V

Voltage drop: . . . . . . . . . V
kV – Verification is OK

Tube current is within specified limits Measurement: . . . . . . . mA

Specified exposure time, (pulses) OK Pulse count: . . . . . . . . . . . . . .

X-ray beam position, panoramic OK

X-ray beam position, ceph OK

The unit is in compliance with MFG specified tests and safety

Technician: Dealer:
D3352.103.01.04.02 59 38 373 D3352
 loqelmelp=ud
Yearly Maintenance Checklist

Customer: _________________________ Address:_________________________

Dealer:____________________________ Address:_________________________

Date of original installation: ___________ Date of inspection: ________________

Report of Assembly FD 2579 # _________

____________________________________
_______
SCHEDULE Yes No Remarks

All manuals are present

Test instruments as required

Manufacturer Model Accuracy Last calibrated
Voltmeter
mAmeter
Pulse counter
Any mechanical damage noticed

All labels are present and legible

All indicator lights are OK

Radiation indicator X-ray lights up, audible buzzer OK

Deadman feature OK

Power supply adequate Line voltage: . . . . . . . . . .V

Voltage drop: . . . . . . . . . V
kV – Verification is OK

Tube current is within specified limits Measurement: . . . . . . . mA

Specified exposure time, (pulses) OK Pulse count: . . . . . . . . . . . . . .

X-ray beam position, panoramic OK

X-ray beam position, ceph OK

The unit is in compliance with MFG specified tests and safety

Technician: Dealer:
D3352.103.01.04.02 59 38 373 D3352
 loqelmelp=ud
Yearly Maintenance Checklist

Customer: _________________________ Address:_________________________

Dealer:____________________________ Address:_________________________

Date of original installation: ___________ Date of inspection: ________________

Report of Assembly FD 2579 # _________

____________________________________
_______
SCHEDULE Yes No Remarks

All manuals are present

Test instruments as required

Manufacturer Model Accuracy Last calibrated
Voltmeter
mAmeter
Pulse counter
Any mechanical damage noticed

All labels are present and legible

All indicator lights are OK

Radiation indicator X-ray lights up, audible buzzer OK

Deadman feature OK

Power supply adequate Line voltage: . . . . . . . . . .V

Voltage drop: . . . . . . . . . V
kV – Verification is OK

Tube current is within specified limits Measurement: . . . . . . . mA

Specified exposure time, (pulses) OK Pulse count: . . . . . . . . . . . . . .

X-ray beam position, panoramic OK

X-ray beam position, ceph OK

The unit is in compliance with MFG specified tests and safety

Technician: Dealer:
D3352.103.01.04.02 59 38 373 D3352
 loqelmelp=ud
Yearly Maintenance Checklist

Customer: _________________________ Address:_________________________

Dealer:____________________________ Address:_________________________

Date of original installation: ___________ Date of inspection: ________________

Report of Assembly FD 2579 # _________

____________________________________
_______
SCHEDULE Yes No Remarks

All manuals are present

Test instruments as required

Manufacturer Model Accuracy Last calibrated
Voltmeter
mAmeter
Pulse counter
Any mechanical damage noticed

All labels are present and legible

All indicator lights are OK

Radiation indicator X-ray lights up, audible buzzer OK

Deadman feature OK

Power supply adequate Line voltage: . . . . . . . . . .V

Voltage drop: . . . . . . . . . V
kV – Verification is OK

Tube current is within specified limits Measurement: . . . . . . . mA

Specified exposure time, (pulses) OK Pulse count: . . . . . . . . . . . . . .

X-ray beam position, panoramic OK

X-ray beam position, ceph OK

The unit is in compliance with MFG specified tests and safety

Technician: Dealer:
D3352.103.01.04.02 59 38 373 D3352
tÉ=êÉëÉêîÉ=íÜÉ=êáÖÜí=íç=ã~âÉ=~åó=~äíÉê~íáçåë=ïÜáÅÜ=ã~ó=ÄÉ=êÉèìáêÉÇ=ÇìÉ=íç=íÉÅÜåáÅ~ä=áãéêçîÉãÉåíëK

= péê~ÅÜÉW=ÉåÖäáëÅÜ= mêáåíÉÇ=áå=dÉêã~åó
aPPROKNMPKMNKMQKMO===NMKOMMT ûKJkêKW= NMU=VSR fãéêáã¨=Éå=^ääÉã~ÖåÉ

páêçå~=aÉåí~ä=póëíÉãë=dãÄe
áå=íÜÉ=rp^W
c~Äêáâëíê~≈É=PN páêçå~=aÉåí~ä=póëíÉãë=ii` lêÇÉê=kç RV=PU=PTP=aPPRO
SQSOR=_ÉåëÜÉáã QUPR=páêçå~=aêáîÉI=pìáíÉ=NMM
dÉêã~åó `Ü~êäçííÉI=k`=OUOTP
ïïïKëáêçå~KÅçã rp^