Addis Ababa University, Faculty of Technology, Department of Civil Engineering

CHAPTER THREE

LATERAL EARTH PRESSURE

Table of Contents

3 Introduction ........................................................................................... 36
3.1 Definitions of Key Terms ....................................................................... 36
3.2 Lateral Earth Pressure at Rest ............................................................... 36
3.3 Active and Passive Lateral Earth Pressures .............................................. 38
3.4 Rankine Active and Passive Earth Pressures ............................................ 38
3.5 Lateral Earth Pressure due to Surcharge ................................................. 42
3.6 Lateral Earth Pressure When Groundwater is Present ................................ 43
3.7 Summary of Rankine Lateral Earth Pressure Theory ................................. 44
3.8 Rankine Active & Passive Earth Pressure for Inclined Granular Backfill ........ 45
3.9 Coulomb’s Earth Pressure Theory ........................................................... 46

Soil Mechanics II: Lecture Notes Instructor: Dr. Hadush Seged 35

Addis Ababa University, Faculty of Technology, Department of Civil Engineering

3 Introduction

A retaining wall is a structure that is used to support a vertical or near vertical

slopes of soil. The resulting horizontal stress from the soil on the wall is called lateral
earth pressure. To determine the magnitude of the lateral earth pressure, a
geotechnical engineer must know the basic soil parameters – that is, unit weight γ ,
angle of friction φ, and cohesion c – for the soil retained behind the wall. In the
evaluation of the magnitude of this lateral earth pressure, it is assumed that the soil
behind the wall (called backfill soil) is on the verge of failure and obeys some failure
criterion, for example, the Mohr-Coulomb failure criterion.
When you complete this chapter, you should be able to:

Understand lateral earth pressure.

Determine lateral earth pressure.

3.1 Definitions of Key Terms

At rest earth pressure coefficient (k0) is the ratio between the lateral and vertical
principal effective stresses when an earth retaining structure is at rest (or is not
allowed to move at all).
Active earth pressure coefficient (ka) is the ratio between the lateral and vertical
principal effective stresses when an earth retaining structure moves away from the
retained soil.
Passive earth pressure coefficient (kp) is the ratio between the lateral and vertical
principal effective stresses when an earth retaining structure is forced to move against
a soil mass.

3.2 Lateral Earth Pressure at Rest

Consider a vertical wall of height H, as shown in Fig. 3.1, retaining a soil having
a unit weight of γ. At any depth z below the ground surface the vertical effective
stress is:

σ v' = γz − u (3.1)

If the wall is not allowed to move at all either way from the soil mass or to the soil
mass (or in other words if there is no lateral expansion or compression in the backfill
soil), the lateral pressure is called at rest earth pressure. In this case, the lateral
earth pressure σ x' at a depth z is:

σ x' = k 0σ z' (3.2)

where k0 is coefficient of at rest earth pressure. You must remember that k0 applies

Soil Mechanics II: Lecture Notes Instructor: Dr. Hadush Seged 36

Addis Ababa University, Faculty of Technology, Department of Civil Engineering

only to effective stresses not to total stresses. The magnitude of k0 depends on the
type of the soil, its degree of compaction, plasticity characteristics, and degree of
disturbance (Bishop, 1958).

Figure 3.1: At rest earth pressure.

For truly normally consolidated soil that exhibits zero cohesion, a value for k0
may be calculated from the following generally accepted empirical equation (Jaky,
1948):

k 0 = 1 − sin φ ' (3.3)

For overconsolidated soils the value of k0 is higher than that given by Eq. (3.3). Alpan
(1967) suggested the following relationship:

k 0,OCR
= (OCR) n (3.4)
k 0,NC

where k0,OCR and k0.NC are the coefficient of at rest earth pressure for overconsolidated
and normally consolidated soil, respectively, OCR is the overconsolidation ratio, and n
is a number depending on the plasticity characteristics of the soil. Based on statistical
analysis of several laboratory test results, Mayne & Kulhawy (1982) proposed that
n = sin φ ' , thus:

k 0,OCR = (1 − sin φ ' )(OCR) sin φ ' (3.5)

EXAMPLE 3.1
For the retaining wall shown in Fig. E3.1, determine the total resultant lateral earth
force at rest per unit length of the wall. Also determine the location of the resultant
earth pressure. Assume that the soil is a normally consolidated soil.

Soil Mechanics II: Lecture Notes Instructor: Dr. Hadush Seged 37

Addis Ababa University, Faculty of Technology, Department of Civil Engineering

FIGURE E3.1

3.3 Active and Passive Lateral Earth Pressures

The lateral earth pressure condition described in section 3.2 involves walls that
do not yield at all. In this section, we will discuss other conditions that involve
movement of the wall and consequently failure of the backfill soil. Failure of the
backfill soil occurs by two mechanisms depending on the direction of wall
displacement. If the displacement of the wall is away from the backfill soil the
resulting failure is called active and the lateral pressure exerted on the wall by the
backfill soil is called active lateral earth pressure or simply active earth pressure. A
passive failure occurs if the wall is displaced towards the backfill soil until the limiting
displacement is achieved. In this case, the wall exerts a pressure on the backfill soil,
and the passive resistance provided by the backfill soil against the wall displacement
is called passive earth pressure.
In the next sections, we will deal with two active and passive earth pressure
theories: one proposed by Rankine (1857) and the other by Coulomb (1776).

3.4 Rankine Active and Passive Earth Pressures

Consider a vertical frictionless (smooth) wall retaining a soil mass in both front
and back of the wall as shown in Fig. 3.2a. If the wall remains rigid and no movement
occurs, then the vertical and horizontal (lateral) effective stresses at rest on element
A, at the back of the wall, and B, at the front of the wall are given by Eqns. (3.1 and
3.2) in section 3.2. Mohr’s circle for the at rest state is shown by circle ① in Fig. 3.2b.
Let us now assume a rotation about the bottom of the wall sufficient to produce
slip planes in the soil mass behind and in front of the wall (Fig. 3.3). The rotation
required, and consequently the lateral displacement or strain, to produce slip planes
in front of the wall is much larger than that required for the back of the wall, as shown
in Fig. 3.4. The soil mass at the back of the wall is assisting in producing failure, thus

Soil Mechanics II: Lecture Notes Instructor: Dr. Hadush Seged 38

Addis Ababa University, Faculty of Technology, Department of Civil Engineering

it is in the active pressure state while the soil mass at the front of the wall is resisting
failure, thus in the passive pressure state.

Figure 3.2: a) A smooth retaining wall, b) Mohr’s circles for at rest, active and passive states.

Figure 3.3: Failure planes within a soil mass near a retaining wall.

Figure 3.4: Rotation required to mobilize active and passive pressures.

Soil Mechanics II: Lecture Notes Instructor: Dr. Hadush Seged 39

Addis Ababa University, Faculty of Technology, Department of Civil Engineering

What happens to the lateral effective stresses on elements A and B when the
wall is rotated? The vertical stress will not change on either element but the lateral
effective stress on element A will be reduced while that for element B will be increased.
We can now plot two additional Mohr’s circles: to represent the stress states of
element A (circle ②) and the other to represent the stress state of element B (circle
③). Both circles are drawn such that the decrease (element A) or increase (element B)
in lateral effective stresses is sufficient to bring the soil to Mohr-coulomb failure state.
In other words, both circles ② and ③ will touch the Mohr-coulomb failure line as
shown in Fig. 3.3 b. For element B to reach the failure state, the lateral effective stress
must be greater than the vertical effective stress, as shown if Fig. 3.3 b.
The stress states of soil elements A and B are called the Rankine active state and
the Rankine passive state, respectively (Named after the first developer of this theory
Rankine, 1857). Each of these Rankine states is associated with a family of failure
planes. For the Rankine active state, the failure planes are oriented at:

φ'
θ a = 45 0 + (3.6)
2
to the horizontal, as illustrated in Fig. 3.3 b and proved in Chapter 1 (Eqn. 1.12). For
the Rankine passive state, the failure planes are oriented at:

φ'
θ p = 45 0 − (3.7)
2
to the horizontal as illustrated in Fig. 3.3 a.
For the active state, the lateral effective stress σ 3' is equal to σ a' as shown in
Fig. 3.2 b (Mohr’s circle ② ). Substituting σ '
a into Eqn. (1.1.7) in Chapter 1, the
Rankine active lateral effective stress is:

1 − sin φ ' 1 − sin φ '

σ a' = σ z' − 2c '
1 + sin φ ' 1 + sin φ '
(3.8)
= σ z' k a − 2c' k a

where,

1 − sin φ ' φ'

ka = = tan 2 (45 − ) (3.9)
1 + sin φ ' 2

is called the active earth pressure coefficient.

For the passive state, the lateral effective stress σ 'p becomes the major

Soil Mechanics II: Lecture Notes Instructor: Dr. Hadush Seged 40

Addis Ababa University, Faculty of Technology, Department of Civil Engineering

principal stress σ 1' and the vertical effective stress σ z' becomes the minor principal
stress σ '
3 as shown in Fig. 3.2 b (Mohr’s circle ③). Therefore, using Eqn. (1.16) in
Chapter 1, the Rankine passive lateral effective stress is:

1 + sin φ ' 1 + sin φ '

σ p' = σ z' + 2c '
1 − sin φ ' 1 − sin φ '
(3.10)
= σ z' k p + 2c' k p

where,

1 + sin φ ' φ'

kp = = tan 2 (45 + ) (3.11)
1 − sin φ ' 2

is called the passive earth pressure coefficient. Based on Eqns. (3.9 and 3.11), we can
easily get the following relation for the active and passive earth pressure coefficients:

1
kp = (3.12)
ka

Equations (3.8) and (3.10) indicate that, for a homogeneous soil layer, the lateral
earth pressure varies linearly with depth z.

Figure 3.5: pressure distribution in c- φ ' soil: a) c- φ ' soil, b) active, c) passive state.

Figure 3.5 shows the active and passive lateral stress distribution for a smooth
wall retaining a c- φ ' soil. In the active state case, the soil at depth z = 0 is subjected
to a tensile stress as shown in Fig. 3.5 b. Soils do not have tensile strength, as a result
tension cracks will occur down to a depth z0, where the tensile stress becomes zero.
At depth z0 (known as depth of tension crack), the stress is zero, thus,

Soil Mechanics II: Lecture Notes Instructor: Dr. Hadush Seged 41

Addis Ababa University, Faculty of Technology, Department of Civil Engineering

2c '
0 = γ ' z 0 k a − 2c ' k a ⇒ z 0 = (3.13)
γ ' ka
The lateral earth force is the area of the lateral stress diagram (Fig. 3.5), which
for the Rankine active state, is:

H
Pa = ∫ (γ ' zk a − 2c ' k a ) = 12 k a γ ' H 2 − 2c' H k a (3.14)
0

and, for the Rankine passive state, is

H
Pp = ∫ (γ ' zk p + 2c' k p ) = 12 k p γ ' H 2 + 2c' H k p (3.15)
0

For most retaining wall construction, a granular backfill is used and c’ = 0,

therefore, for granular soils Eqns. (3.13) and (3.14) can be rewritten as:

Pa = 12 k a γ ' H 2 (3.16)

and

Pp = 12 k p γ ' H 2 (3.17)

EXAMPLE 3.2
Draw the active pressure diagram per meter length of an 8 m high smooth vertical
retaining wall. Also, calculate a) tension crack depth and b) the resultant (total)
active force and its location. The properties of the backfill soil are c’ = 20 kPa,
φ ' =250 and γ =17.5 kN/m3. Note that the tension zone is usually ignored for
finding the magnitude and location of the resultant force.

3.5 Lateral Earth Pressure due to Surcharge

Surfaces stresses (due to surcharge) also impose lateral pressure on retaining

walls as illustrated in Fig. 3.6 d. A uniform surface stress, qs, will transmit a uniform
active lateral earth pressure of kaqs and a uniform passive lateral earth pressure of
kpqs. The active and passive lateral stresses due to the soil (i.e. c’, φ ' soil), and the
uniform surfaces stresses are then:
σ a' = k a γ ' z + k a q s (3.18)

and σ p' = k p γ ' z + k p q s (3.19)

The corresponding active and passive lateral forces are also given by:

Soil Mechanics II: Lecture Notes Instructor: Dr. Hadush Seged 42

Addis Ababa University, Faculty of Technology, Department of Civil Engineering

Pa = 12 k a γ ' H 2 + k a q s H (3.20)

and

Pp = 12 k p γ ' H 2 + k p q s H (3.21)

Figure 3.6: Variation of active and passive lateral earth pressures, hydrostatic
pressure, and a uniform surface stress with depth. (Note: backfill soil is granular).

For a c’, φ ' backfill, Eqns. (3.18) and (3.19) will become:

σ a' = k a γ ' z + k a q s − 2c' k a (3.22)

and σ p' = k p γ ' z + k p q s + 2c' k p (3.23)

The corresponding active and passive lateral forces are also given by:

Pa = 12 k a γ ' H 2 + k a q s H − 2c' H k a (3.24)

and

Pp = 12 k p γ ' H 2 + k p q s H + 2c' k p (3.25)

Note that for a purely cohesive saturated clay with undrained shear strength
parameter of cu and φ ' u=0, ka = kp = 1.

3.6 Lateral Earth Pressure When Groundwater is Present

If groundwater is present, you need to add the hydrostatic pressure (pore water

Soil Mechanics II: Lecture Notes Instructor: Dr. Hadush Seged 43

Addis Ababa University, Faculty of Technology, Department of Civil Engineering

pressure) to the lateral earth pressure. For example, if the groundwater level is at a
distance hw from the base of the wall as shown in Fig. 3.6, the hydrostatic pressure is,

u = γ w hw (3.26)

and the hydrostatic force is:

Pw = 12 γ w hw2 (3.27)

3.7 Summary of Rankine Lateral Earth Pressure Theory

1. The lateral earth pressures on retaining walls are related directly to the vertical
effective stress through two coefficients ka and kp.
2. Substantially more movement is required to mobilize the full passive earth
pressure than the full active earth pressure.
3. A family of slip planes occurs in the Rankine active and passive states. In the
active state, the slip planes are oriented at (450 + φ ' / 2 ) to the horizontal, and
while for the passive case they are oriented at (45 0
- φ ' / 2 ) to the horizontal.
4. The lateral earth pressure coefficients, developed so far are only valid for a smooth,
vertical wall supporting a soil mass with a horizontal surface; and must be applied
to effective stresses only.

EXAMPLE 3.3
For the frictionless wall retaining a stratified soil and shown in Fig. E3.2, determine:
(a) The active lateral earth pressure distribution with depth.
(b) The passive lateral earth pressure distribution with depth.
(c) The magnitude and location of the active and passive forces.
(d) The resultant force.
(e) The ratio of passive moment to active moment.

FIGURE E3.2

Soil Mechanics II: Lecture Notes Instructor: Dr. Hadush Seged 44

Addis Ababa University, Faculty of Technology, Department of Civil Engineering

Strategy There are two layers. It is best to treat the layers separately. Neither ka nor
kp should be applied to the pore water pressure. You do not need kp for the top soil
layer. Since the water level on both sides of the wall is the same, the resultant
hydrostatic force is zero. However, you are asked to determine the forces on each side
of the wall; therefore, you have to consider the hydrostatic force. A table is helpful to
solve this type of problem.

3.8 Rankine Active & Passive Earth Pressure for Inclined Granular Backfill

If the backfill of a frictionless retaining wall is a granular soil (c = 0, φ ) and rises

'

at an angle β ( β ≤ φ ' ) with respect to the horizontal (Figure 3.7), the Rankine active
earth pressure coefficient ka is expressed in the form:

cos β − cos 2 β − cos 2 φ '

k a = cos β (3.28)
cos β + cos 2 β − cos 2 φ '

The Rankine active stress on the wall is:

σ a' = γ ' zk a (3.29)

and the Rankine active lateral force is:

Pa = 12 k a γ ' H 2 (3.30)

Note that, the direction of the lateral force Pa is inclined at an angle β to the
horizontal and intersects the wall at a distance of H/3 from the base of the wall.

Figure 3.7: Rankine Active Earth Pressure for Inclined Granular Backfill

The Rankine passive pressure coefficient kp for a wall with a granular sloping

Soil Mechanics II: Lecture Notes Instructor: Dr. Hadush Seged 45

Addis Ababa University, Faculty of Technology, Department of Civil Engineering

backfill is:

cos β + cos 2 β − cos 2 φ '

k p = cos β (3.31)
cos β − cos 2 β − cos 2 φ '

The Rankine passive stress and passive lateral force are calculated using equations
similar to Eqns. (3.24 and 3.25) in which ka is replaced by kp. As in the case of the
active force, the resultant force Pp is inclined at angle β with the horizontal and
intersects the wall at a distance of H/3 from the bottom of the wall.

EXAMPLE 3.4
A retaining wall with a vertical back is 5 m high and retains a sloping soil with β =200.
Determine the magnitude of the active pressure.

3.9 Coulomb’s Earth Pressure Theory

As described in the previous sections, the Rankine earth pressure theory: (1)
assumes the retaining wall is frictionless (or smooth), and (2) considers stress states
and uses such tools as the Mohr’s circle of stress. Coulomb (1776) proposed a theory
to determine the lateral earth pressure on a retaining wall by assuming a granular
backfill (c = 0) and a plane sliding surface. He did this in order to simplify somewhat
the mathematically complex problem introduced when cohesion and nonplane sliding
surfaces are considered. He, however, account for the effects of friction (usually
expressed by angle δ ) between the backfill and the wall. Besides, he considered the
more general case of the sloped face of a retaining wall, and in this respect, Coulomb’s
theory is a more general approach than the Rankine theory described earlier.

Figure 3.8: Direction of active and passive forces when wall friction is present.

Coulomb assumed a wedge shape collapse mechanism which is bounded by the

face of the retaining wall, a horizontal or inclined ground surface and a linear failure
plane. The wedge slides downwards on the failure plane in the active state or upwards

Soil Mechanics II: Lecture Notes Instructor: Dr. Hadush Seged 46

Addis Ababa University, Faculty of Technology, Department of Civil Engineering

in the passive state. Figure 3.8 illustrates direction of active and passive forces when
wall friction is present.

Figure 3.9: Retaining wall with slopping back, wall friction, and sloping soil surface
for use with Coulomb’s method for active state.

Based on Coulomb’s theory, a condition of limit equilibrium exists through which

a wedge of a soil mass behind a retaining wall will slip along a plane inclined at an
angle θ to the horizontal. Figure 3.9 illustrates a retaining wall with slopping back,
wall friction, and sloping soil surface for use with Coulomb’s method for active state.
Based on the equilibrium of the forces acting on the wedge (Fig. 3.9), Coulomb
proposed the following equation to determine the active lateral force,

Pa = 12 k ac γ ' H 2 (3.32)

where kac is Coulomb’s active pressure coefficient, which is determined by the

following expression.

sin 2 ( β + φ ' )
k ac = 2
(3.33)
 sin(φ '+δ ) sin(φ '−α ) 
sin 2 β sin( β − δ ) 1 + 
 sin( β − δ ) sin(α + β ) 

Note that the line of action of the active force Pa will act at a distance H/3 above
the base of the wall and will be inclined at angle δ to the normal drawn to the back
of the wall. In the actual design of retaining walls, the value of the wall friction
angle, δ , is assumed to be between φ'
2 and 2
3 φ' . Retaining walls are generally
constructed of masonry or mass concrete. Table 3.1 shows the general range of the
values of δ for various backfill materials.

Soil Mechanics II: Lecture Notes Instructor: Dr. Hadush Seged 47

Addis Ababa University, Faculty of Technology, Department of Civil Engineering

Table 3.1: General range of wall friction angle for masonry or mass concrete walls
Backfill material Range of δ in degrees
Gravel 27 – 30
Course sand 20 – 28
Fine sand 15 – 25
Stiff clay 15 – 20
Silty clay 12 – 16

Coulomb’s passive earth pressure is determined similarly, except that passive

pressure inclination at the wall and direction of the forces acting on the wedge will be
as shown in Fig. 3.10. Coulomb’s passive earth pressure is given by:

Pa = 12 k ac γ ' H 2 (3.34)

where kpc is Coulomb’s passive pressure coefficient, which is determined by the

following equation.

sin 2 ( β − φ ' )
k pc = 2
(3.35)
 sin(φ '+δ ) sin(φ '+α ) 
sin 2 β sin( β + δ ) 1 − 
 sin( β + δ ) sin(α + β ) 

Figure 3.10: Retaining wall with slopping back, wall friction, and sloping soil surface
for use with Coulomb’s method for passive state.

EXAMPLE 3.5
What is the total active force per meter of wall for the soil-wall system, shown in Fig.
E3.4 using the Coulomb equation? Where does Pa act?

Soil Mechanics II: Lecture Notes Instructor: Dr. Hadush Seged 48

Addis Ababa University, Faculty of Technology, Department of Civil Engineering

Figure: E3.5

Soil Mechanics II: Lecture Notes Instructor: Dr. Hadush Seged 49