NPK-CHEMICAL

PROJECT
500,000 MTPY
MECHANICAL DATA SHEET DOCUMENT NO. : NPK-000-R11-DS-4006-V
ZA WEIGHER FEEDER REVISION NO. : 0
(81-MWQ-316/TEFC) PAGE : 3 OF 3
1 SITE : KRUENG GEUKEUH, NORTH ACEH SPECIFICATION : - Rev.
2 SERVICE : 81-D-316 TYPE : Weighfeeder
3 NO. REQUIRED: 1 (ONE) MANUFACTURER: Schenck Process
4 MODEL NO. : MTD-E 0870
5 OPERATING CONDITIONS
6 Product Handled ZA Bulk Density 1100 - 1200 Kg/ m³
7 Respose Angle 32 - 38 Temperature Ambient °C
8 Granulometry Moisture Max 3 %
9 1 - 3,5 mm 97 % Dust Vent (2)
10 > 3,5 mm 3 % Corrosion Slight
11 Adherence Yes
12 Normal Flow 3,5 - 35 T/h Service Continuous 24 h/d
13 Design Flow 3,5 - 35 T/h DRIVER
14 Item Number / Type 81 - MWQ - 316 / TEFC
15 MATERIALS OF CONSTRUCTION [4] Power / Speed 0,37-1,1 / (1) kW/Rpm
16 Belt Width 800 mm Volt/Phase/Frequency 380 / 3 / 50
17 Center to Center Lenght 7000 mm Protection/Insulation Min. IP 55 / F / B
18 Belt speed Variable Speed Supplied By VENDOR
19 Cross Section Stream Section 90 x 98 mm SPEED VARIATOR
20 Difference of level Horizontal mm Item Number tbd (1)
21 Feed Inlet Hooper With Flange (1) Ratio/ Speed tbd
22 Discharge Outlet Flange (1) GEAR
23 Idlers Angle 0 (1) Item Number tbd (1)
24 Frame supplied by Schenck Process (1) MANUFACTURER tbd
25 Supports supplied by Schenck Process (1) Type tbd
26 IDLERS Dia. mm LENGTH BEARINGS DISTANCE Ratio tbd (1)
27 Carrying 108 (1) (1) (1) Service factor tbd
28 Return 190 (1) (1) (1) PULLEYS
29 Drive Pulley Diameter 190 (1) mm
30 Driving unit arrang. Motor- Gear Frequency Variator Drive Pulley Lenght tbd (1) mm
31 Take up arrangement Yes No Tail Pulley Diameter 190 (1) mm
32 Weighing accuracy 0.5 % (1% Max.) Tail Pulley Lenght tbd (1) mm
33 Cell Protection IP 67 Bearings tbd (1)
34 ACCESSORIES Bearings Seal tbd (1)
35 Belt cleaner Yes No BELT
36 Back Stop Yes No Type Endless
37 Safety Rop Yes No Quality Oil resistant (OR) (1) (4)
38 Deviation switch Yes No Surface (1)(4)
39 Skirt Yes No Number of Piles (1)
40 Cover & Filter Yes No Canvas Quality (1)
41 Inspection door Yes No Thickness Upper Face (1) mm
42 Instrument control system Yes No Thickness Lower Face (1) mm
Feed Hopper &
43 Yes No Belt Weight/ Running Meter (1) kg
discharge hooper
44 WEIGHT Developed lenght (1) mm
45 Frame (1) kg Lining (1)
46 Rolls (1) kg Vulcanized Belt (1)
47 Belt (1) kg INSPECTION AND TEST ITEM
48 Weighing Set (1) kg Shop Inspection REQ'D WIT.
49 Total approx 2,2 T Appearance Check REQ'D WIT.
50 REMARKS Dimension Check REQ'D WIT.
51 Temporary Assembly REQ'D WIT.
52 Mechanical Run REQ'D WIT.
53 Field Test REQ'D WIT.
54 SKETCH
55
56 Please refer to Mechanical Drawing
57 V944983B11 - MultiDos E 0870_SN V157386A01_ZA - Rev B
58
59
60
61