K7VT4A+

User Manual

Version 1.0
Published May 2004
Copyright©2004 ASRock INC. All rights reserved.

1
Copyright Notice:
No part of this manual may be reproduced, transcribed, transmitted, or translated in
any language, in any form or by any means, except duplication of documentation by
the purchaser for backup purpose, without written consent of ASRock Inc.
Products and corporate names appearing in this manual may or may not be regis-
tered trademarks or copyrights of their respective companies, and are used only for
identification or explanation and to the owners’ benefit, without intent to infringe.

Disclaimer:
Specifications and information contained in this manual are furnished for informa-
tional use only and subject to change without notice, and should not be constructed
as a commitment by ASRock. ASRock assumes no responsibility for any errors or
omissions that may appear in this manual.
With respect to the contents of this manual, ASRock does not provide warranty of
any kind, either expressed or implied, including but not limited to the implied warran-
ties or conditions of merchantability or fitness for a particular purpose.
In no event shall ASRock, its directors, officers, employees, or agents be liable for
any indirect, special, incidental, or consequential damages (including damages for
loss of profits, loss of business, loss of data, interruption of business and the like),
even if ASRock has been advised of the possibility of such damages arising from any
defect or error in the manual or product.

This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.

ASRock Website: http://www.asrock.com

2
 Contents
1. Introduction ....................................................... 4
1.1 Package Contents ................................................................ 4
1.2 Specifications ...................................................................... 5
1.3 Motherboard Layout ............................................................ 7
1.4 ASRock I/OTM .......................................................................................................................... 8
2. Installation ......................................................... 9
Pre-installation Precautions ......................................................... 9
2.1 CPU Installation .................................................................... 10
2.2 Installation of CPU Fan and Heatsink .................................. 10
2.3 Installation of Memory Modules (DIMM) ............................... 11
2.4 Expansion Slots (PCI and AGP Slots) ................................. 12
2.5 Jumpers Setup .................................................................... 13
2.6 Onboard Headers and Connectors .................................... 15
3. BIOS Setup ......................................................... 17
3.1 BIOS Setup Utility ................................................................. 17
3.1.1 BIOS Menu Bar .......................................................... 17
3.1.2 Legend Bar ................................................................ 18
3.2 Main Menu ............................................................................ 18
3.3 Advanced, Security, Power, Boot, and Exit Menus ........... 20
4. Software Support .............................................. 21
4.1 Install Operating System ...................................................... 21
4.2 Support CD Information ........................................................ 21
4.2.1 Running Support CD .................................................. 21
4.2.2 Drivers Menu ............................................................. 21
4.2.3 Utilities Menu .............................................................. 21
4.2.4 ASRock “PC-DIY Live Demo” Program ...................... 21
4.2.5 Contact Information .................................................... 21
Appendix ............................................................... 22
1. Advanced BIOS Setup Menu ............................................... 22
2. Security Setup Menu ........................................................... 27
3. Power Setup Menu .............................................................. 28
4. Boot Setup Menu ................................................................. 29
5. Exit Menu .............................................................................. 30

3
1. Introduction
Thank you for purchasing ASRock K7VT4A+ motherboard, a reliable motherboard
produced under ASRock’s consistently stringent quality control. It delivers excellent
performance with robust design conforming to ASRock’s commitment to quality and
endurance.
Chapter 1 and 2 of this manual contain introduction of the motherboard and step-by-
step installation guide. Chapter 3 and 4 contain basic BIOS setup and support CD
information. More information of advanced BIOS setup can be found in Appendix on
page 22 for advanced users’ reference.

Because the motherboard specifications and the BIOS software might

be updated, the content of this manual will be subject to change
without notice. In case any modifications of this manual occur, the
updated version will be available on ASRock website without further
notice. You may find the latest memory and CPU support lists on
ASRock website as well. ASRock website http://www.asrock.com

1.1 Package Contents

1 x ASRock K7VT4A+ Motherboard
(ATX Form Factor: 12.0-in x 7.0-in, 30.5 cm x 17.8 cm)
1 x ASRock K7VT4A+ Quick Installation Guide
1 x ASRock K7VT4A+ Support CD
1 x Ultra ATA 66/100/133 IDE Ribbon Cable (80-conductor)
1 x 3.5-in Floppy Drive Ribbon Cable
1 x ASRock I/OTM Shield

4
1.2 Specifications
Platform: ATX Form Factor: 12.0-in x 7.0-in, 30.5 cm x 17.8 cm
CPU: Supports Socket A (462 pins) for
AMD AthlonTM / AthlonTM XP / DuronTM processor
Chipsets: North Bridge: VIA KT400A, FSB@333 MHz
South Bridge: VIA VT8235CD, supports USB 2.0, ATA 133
Memory: 2 DDR DIMM Slots: DDR1 and DDR2
PC3200 (DDR400) for 1 DDR DIMM slot, Max. 1GB
PC2100 (DDR266) / PC2700 (DDR333) for 2 DDR DIMM slots,
Max. 2GB
IDE: IDE1: ATA 133 / Ultra DMA Mode 6
IDE2: ATA 133 / Ultra DMA Mode 6
Supports up to 4 IDE devices
Floppy Port: Supports up to 2 floppy disk drives
Audio: 5.1 channels AC’97 Audio
LAN: Speed: 802.3u (10/100 Ethernet), supports Wake-On-LAN
Hardware Monitor: CPU temperature sensing
Motherboard temperature sensing
CPU overheat shutdown to protect CPU life
(ASRock U-COP)(see CAUTION 1)
CPU fan tachometer
Chassis fan tachometer
Voltage monitoring: +12V, +5V, +3.3V, Vcore
PCI slots: 5 slots with PCI Specification 2.2
AGP slot: 1 AGP slot, supports 1.5V, 8X/4X AGP card (see CAUTION 2)
USB 2.0: 6 USB 2.0 ports:
includes 4 default USB 2.0 ports on the rear panel,
plus one header to support 2 additional USB 2.0 ports
(see CAUTION 3)
ASRock I/OTM: 1 PS/2 keyboard port, 1 PS/2 mouse port,
1 serial port: COM1, 1 parallel port: ECP/EPP support,
1 RJ-45 port,
4 default USB 2.0 ports,
Audio Jack: Line Out / Line In / Microphone + Game port
BIOS: AMI legal BIOS, Supports “Plug and Play”,
ACPI 1.1 compliance wake up events,
SMBIOS 2.3.1 support,
CPU frequency stepless control
(only for advanced users’ reference, see CAUTION 4)
OS: Microsoft® Windows® 98 SE / ME / 2000 / XP compliant

5
CAUTION!
1. While CPU overheat is detected, the system will automatically shutdown.
Before you resume the system, please check if the CPU fan on the
motherboard functions properly and unplug the power cord, then plug it
back again. To improve heat dissipation, remember to spray thermal
grease between the CPU and the heatsink when you install the PC system.
2. Do NOT use a 3.3V AGP card on the AGP slot of this motherboard!
It may cause permanent damage!
3. Power Management for USB 2.0 works fine under Microsoft® Windows®
XP SP1/2000 SP4. It may not work properly under Microsoft® Windows®
98/ME. Please refer to Microsoft® official document at
http://www.microsoft.com/whdc/hwdev/bus/USB/USB2support.mspx
4. Although this motherboard offers stepless control, it is not recommended
to perform over clocking. Frequencies other than the recommended CPU
bus frequencies may cause the instability of the system or damage the
CPU. The CPU host frequency of this motherboard is determined by the
jumper-setting. You must set the FSB jumper according to your AMD CPU
before you use the “Manual” option as the FSB setting in BIOS setup to
perform over clocking. Please check page 22 for details.

6
1.3 Motherboard Layout
1 2 3 4 5 6
17.8cm (7.0 in)

PS/2 PS2_USB_PWR1
MOUSE 1
CPU_FAN1
PARALLEL PORT
PS/2
KEYBOARD FID4 1
FID3 1
FID2 1
FID1 1

ATXPWR1
FID0 1 SOCKET 462
J1
SERIAL
PORT
(COM1)

30.5cm (12.0 in)

DDR 1 (64/72 bit, 184-pin module)

DDR2 (64/72 bit, 184-pin module)

26
LAN
USB 2.0
PORTS IDE1 IDE2

USB 2.0
PORTS

25
AUDIO1
GAME AUDIO1

LINE OUT

VIA
Line
LINE IN
In KT400A
GAME_

AUX1 CHIPSET
Mic
MIC IN
In
7
24 JR1
CD1
8
23 1
AUDIO1
AGP 8X K7VT4A+
JL1
22 1.5V_AGP1 9
LAN
AUDIO PHY
CODEC

PCI1
1 FSB_SEL0
DDR400 1
1
FSB_SEL1
FSB_SEL2
10
SUPER PCI2
I/O

21 PCI3 11
2MB
USB2.0
VIA
20 BIOS 5.1CH VT8235 12
PCI4 CHA_FAN1

CMOS ATA133
BATTERY FSB333 13
PCI5 FLOPPY1
PWR_LED1

1 CLRCMOS2
1
PANEL 1
PLED PWRBTN
14
1 1 1 1
IR1 USB45 SPEAKER1 HDLED RST

19 18 17 16 15

1 PS2_USB_PWR1 Jumper 14 Power LED Connector (PWR_LED1)

2 CPU Fan Connector (CPU_FAN1) 15 System Panel Connector (PANEL1)
3 CPU Socket 16 Chassis Speaker Connector (SPEAKER 1)
4 North Bridge Controller 17 USB 2.0 Connector (USB45, Blue)
5 184-pin DDR DIMM Slots (DDR1- 2) 18 Infrared Module Connector (IR1)
6 ATX Power Connector (ATXPWR1) 19 Clear CMOS Jumper (CLRCMOS2)
7 Secondary IDE Connector (IDE2, Black) 20 Flash Memory
8 Primary IDE Connector (IDE1, Blue) 21 PCI Slots (PCI1- 5)
9 AGP Slot (1.5V_AGP1) 22 Front Panel Audio Connector (AUDIO1)
10 FSB Select Jumpers 23 JR1 / JL1 Jumpers
(FSB_SEL0, FSB_SEL1, FSB_SEL2) 24 Internal Audio Connector: CD1 (Black)
11 South Bridge Controller 25 Internal Audio Connector: AUX1 (White)
12 Chassis Fan Connector (CHA_FAN1) 26 J1 Jumper (FID0, FID1, FID2, FID3, FID4)
13 Floppy Connector (FLOPPY1)

7
1.4 ASRock I/O TM

1 2 3

10 9 8 7 6 5 4

1 Parallel Port 6 Line Out (Lime)

2 RJ-45 Port 7 USB 2.0 Ports
3 Game Port 8 Serial Port (COM1)
4 Microphone (Pink) 9 PS/2 Keyboard Port (Purple)
5 Line In (Light Blue) 10 PS/2 Mouse Port (Green)

8
2. Installation
K7VT4A+ is an ATX form factor (12.0-in x 7.0-in, 30.5 cm x 17.8 cm) motherboard.
Before you install the motherboard, study the configuration of your chassis to en-
sure that the motherboard fits into it.

Pre-installation Precautions
Take note of the following precautions before you install motherboard
components or change any motherboard settings.

Before you install or remove any component, ensure that the

power is switched off or the power cord is detached from the
power supply. Failure to do so may cause severe damage to the
motherboard, peripherals, and/or components.

1. Unplug the power cord from the wall socket before touching any
component.
2. To avoid damaging the motherboard components due to static
electricity, NEVER place your motherboard directly on the carpet or
the like. Also remember to use a grounded wrist strap or touch a
safety grounded object before you handle components.
3. Hold components by the edges and do not touch the ICs.
4. Whenever you uninstall any component, place it on a grounded anti-
static pad or in the bag that comes with the component.
5. When placing screws into the screw holes to secure the motherboard
to the chassis, please do not over-tighten the screws! Doing so may
damage the motherboard.

9
2.1 CPU Installation
o
Step 1. Unlock the socket by lifting the lever up to a 90 angle.
Step 2. Position the CPU directly above the socket such that its marked corner
matches the base of the socket lever.
Step 3. Carefully insert the CPU into the socket until it fits in place.

The CPU fits only in one correct orientation. DO NOT force the
CPU into the socket to avoid bending of the pins.

Step 4. When the CPU is in place, press it firmly on the socket while you push
down the socket lever to secure the CPU. The lever clicks on the side tab
to indicate that it is locked.

Step 1 Step 2, 3 Step 4

2.2 Installation of CPU Fan and Heatsink

AMD AthlonTM / AthlonTM XP/ DuronTM family CPUs with a speed of 600 MHz and
higher require larger heatsink and cooling fan. Thermal grease between the
CPU and the heatsink is also needed to improve heat transfer. Make sure that
the CPU and the heatsink are securely fastened and in good contact with
each other. Then connect the CPU fan to the CPU_FAN connector (CPU_FAN1,
see page 7, No. 2). For proper installation, please kindly refer to the instruc-
tion manuals of the CPU fan and heatsink vendors.

10
2.3 Installation of Memory Modules (DIMM)
K7VT4A+ motherboard provides two 184-pin DDR (Double Data Rate) DIMM slots.

Please make sure to disconnect power supply before adding or

removing DIMMs or the system components.

Step 1. Unlock a DIMM slot by pressing the retaining clips outward.

Step 2. Align a DIMM on the slot such that the notch on the DIMM matches the break
on the slot.

notch
break

notch
break

The DIMM only fits in one correct orientation. It will cause permanent
damage to the motherboard and the DIMM if you force the DIMM into
the slot at incorrect orientation.

Step 3. Firmly insert the DIMM into the slot until the retaining clips at both ends fully
snap back in place and the DIMM is properly seated.

11
2.4 Expansion Slots (PCI and AGP Slots)
There are 5 PCI slots and 1 AGP slot on K7VT4A+ motherboard.
PCI slots: PCI slots are used to install expansion cards that have the 32-bit PCI
interface.
AGP slot: The AGP slot is used to install a graphics card. The ASRock AGP slot has
a special design of clasp that can securely fasten the inserted graphics
card.

Please do NOT use a 3.3V AGP card on the AGP slot of this motherboard!
It may cause permanent damage! For the voltage information of your
graphics card, please check with the graphics card vendors.

Installing an expansion card

Step 1. Before installing the expansion card, please make sure that the power
supply is switched off or the power cord is unplugged. Please read the
documentation of the expansion card and make necessary hardware
settings for the card before you start the installation.
Step 2. Remove the system unit cover (if your motherboard is already installed
in a chassis).
Step 3. Remove the bracket facing the slot that you intend to use.
Keep the screws for later use.
Step 4. Align the card connector with the slot and press firmly until the card is
completely seated on the slot.
Step 5. Fasten the card to the chassis with screws.
Step 6. Replace the system cover.

12
2.5 Jumpers Setup
The illustration shows how jumpers are
setup. When the jumper cap is placed on
pins, the jumper is “Short”. If no jumper cap
is placed on the pins, the jumper is “Open”.
The illustration shows a 3-pin jumper whose
pin1 and pin2 are “Short” when jumper cap
is placed on these 2 pins.

Jumper Setting
FSB Select Jumpers 1_2 OPEN 2_3 OPEN
FSB_SEL0 FSB_SEL0 FSB_SEL0 FSB_SEL0
(FSB_SEL0,
OPEN 2_3 OPEN 1_2
FSB_SEL1, FSB_SEL1 FSB_SEL1
FSB_SEL1 FSB_SEL1
FSB_SEL2) 1_2 1_2 1_2 2_3
(see p.7 item 10) FSB_SEL2 FSB_SEL2 FSB_SEL2 FSB_SEL2
FSB 200MHz FSB 266MHz FSB 333MHz FSB 400MHz

Note: The CPU FSB frequency of this motherboard is determined by jumper-setting. You must
adjust “FSB Select Jumpers” according to the FSB of your AMD CPU. Please follow the
figures above to set the CPU FSB frequency.

1_2 2_3
PS2_USB_PWR1 Short pin2, pin3 to enable
(see p.7 item 1) +5V +5VSB +5VSB (standby) for PS/2 or
USB wake up events.
Note: To select +5VSB, it requires 2 Amp and higher standby current provided by power
supply.

JR1 / JL1 Jumpers JR1

(see p.7 item 23) JL1

Note: If JR1 and JL1 Jumpers are short, both the front panel and the rear panel audio
connectors can work.

Clear CMOS Jumper

(CLRCMOS2)
2-pin jumper
(see p.7 item 19)

Note: CLRCMOS2 allows you to clear the data in CMOS. The data in CMOS includes system
setup information such as system password, date, time, and system setup parameters. To
clear and reset the system parameters to default setup, please turn off the computer and
unplug the power cord from the power supply. After waiting for 15 seconds, use a jumper
cap to short the Clear CMOS jumper for 5 seconds. After shorting the Clear CMOS jumper,
please remove the jumper cap. However, please do not clear the CMOS right after you
update the BIOS. If you need to clear the CMOS when you just finish updating the BIOS,
you must boot up the system first, and then shut it down before you do the clear-CMOS
action.

13
J1 Jumper FID4 1
FID3 1
(FID0, FID1, FID2, FID3, FID4)
FID2 1
(see p.7 item 26)
FID1 1
FID0 1

Note: The set of J1 jumper is only for advanced users to adjust the multiplier of CPU. Please
follow the table below to adjust the multiplier of CPU. However, the system will work well
without the adjustment of multiplier. You do not have to adjust the multiplier for normal
usage.

Multiplier FID0 FID1 FID2 FID3 FID4

5x 2-3 2-3 1-2 2-3 2-3
5.5x 1-2 2-3 1-2 2-3 2-3
6x 2-3 1-2 1-2 2-3 2-3
6.5x 1-2 1-2 1-2 2-3 2-3
7x 2-3 2-3 2-3 1-2 2-3
7.5x 1-2 2-3 2-3 1-2 2-3
8x 2-3 1-2 2-3 1-2 2-3
8.5x 1-2 1-2 2-3 1-2 2-3
9x 2-3 2-3 1-2 1-2 2-3
9.5x 1-2 2-3 1-2 1-2 2-3
10x 2-3 1-2 1-2 1-2 2-3
10.5x 1-2 1-2 1-2 1-2 2-3
11x 2-3 2-3 2-3 2-3 2-3
11.5x 1-2 2-3 2-3 2-3 2-3
12x 2-3 1-2 2-3 2-3 2-3
12.5x 1-2 1-2 2-3 2-3 2-3
13x 2-3 2-3 1-2 2-3 1-2
13.5x 1-2 2-3 1-2 2-3 1-2
14x 2-3 1-2 1-2 2-3 1-2
15x 2-3 2-3 2-3 1-2 1-2
16x 2-3 1-2 2-3 1-2 1-2
16.5x 1-2 1-2 2-3 1-2 1-2
17x 2-3 2-3 1-2 1-2 1-2
18x 1-2 2-3 1-2 1-2 1-2
19x 1-2 2-3 2-3 2-3 1-2
20x 1-2 1-2 2-3 2-3 1-2
21x 1-2 1-2 1-2 2-3 1-2
22x 1-2 2-3 2-3 1-2 1-2
23x 2-3 1-2 1-2 1-2 1-2
24x 1-2 1-2 1-2 1-2 1-2

For example, “Athlon XP 2000+” is an 1666MHz CPU: 12.5 (Multiplier) X 133MHz (External frequency) = 1666MHz
J1 jumper setting: FID4 1
FID3 1
FID2 1
FID1 1
FID0 1

The jumper caps are not provided by ASRock. Please understand that ASRock
does not guarantee and support the adjustment of multiplier. These jumpers
setting may not apply to all multiplier-locked or even some unlocked AMD
CPU. Frequencies other than the recommended CPU bus frequencies may
cause the instability of the system or damage the CPU.

14
2.6 Connectors

Connectors are NOT jumpers. DO NOT place jumper caps over these
connectors. Placing jumper caps over the connectors will cause perma-
nent damage of the motherboard!

Connector Figure Description

FDD Connector
(33-pin FLOPPY1)
(see p.7 item 13) Pin1 FLOPPY1
the red-striped side to Pin1

Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.

Primary IDE Connector (Blue) Secondary IDE Connector (Black)

(39-pin IDE1, see p.7 item 8) (39-pin IDE2, see p.7 item 7)

PIN1 IDE1 PIN1 IDE2

connect the blue end connect the black end

to the motherboard to the IDE devices
80-conductor, ATA 66/100/133 cable
Note: If you use only one IDE device on this motherboard, please set the IDE
device as “Master”. Please refer to the instruction of your IDE device vendor
for the details. Besides, to optimize compatibility and performance, please
connect your hard disk drive to the primary IDE connector (IDE1, blue) and
CD-ROM to the secondary IDE connector (IDE2, black).

USB_PWR
USB 2.0 Connector P-5
ASRock I/OTM provides you 4
P+5
(9-pin USB45) GND
DUMMY
default USB 2.0 ports on the rear
(see p.7 item 17) panel. If the rear USB ports are
1
GND
not sufficient, this USB 2.0
P+4
P-4 connector is available to support
USB_PWR
2 additional USB 2.0 ports.

Infrared Module Connector IRTX

+5V
This connector supports an
DUMMY
(5-pin IR1) optional wireless transmitting
(see p.7 item 18) 1 and receiving infrared module.
GND
IRRX

15
Internal Audio Connectors AUX-R These connectors allow you to
GND
(4-pin CD1, 4-pin AUX1) GND
AUX1 receive stereo audio input from
AUX-L
(CD1: see p.7 item 24) sound sources such as a CD-
CD-R
(AUX1: see p.7 item 25) GND
CD1 ROM, DVD-ROM, TV tuner card,
GND
CD-L
or MPEG card.

GND
Front Panel Audio Connector +5VA This is an interface for front panel
BACKOUT-R
(9-pin AUDIO1) BACKOUT-L audio cable that allows conve-
(see p.7 item 22)
1
nient connection and control of
AUD-OUT-L audio devices.
DUMMY
AUD-OUT-R
MIC-POWER
MIC

System Panel Connector PLED+ This connector accommodates

PLED-
PWRBTN#
(9-pin PANEL1) GND several system front panel
(see p.7 item 15) functions.
1
DUMMY
RESET#
GND
HDLED-
HDLED+

Chassis Speaker Connector 1 Please connect the chassis

SPEAKER
(4-pin SPEAKER 1) DUMMY speaker to this connector.
DUMMY
(see p.7 item 16) +5V

Chassis Fan Connector GND Please connect a chassis fan

+12V
(3-pin CHA_FAN1) CHA_FAN_SPEED cable to this connector and
(see p.7 item 12) match the black wire to the
ground pin.

CPU Fan Connector CPU_FAN_SPEED Please connect a CPU fan cable

+12V
(3-pin CPU_FAN1) GND to this connector and match
(see p.7 item 2) the black wire to the ground pin.

ATX Power Connector Please connect an ATX power

(20-pin ATXPWR1) supply to this connector.
(see p.7 item 6)

Power LED Connector Please connect a 3-pin power

1
(3-pin PWR_LED1) PLED- LED cable to this connector.
PLED+
PLED+
(see p.7 item 14)

16
3. BIOS Setup
3.1 BIOS Setup Utility
This section explains how to use the BIOS Setup Utility to configure your system.
The Flash Memory on the motherboard stores the BIOS Setup Utility. You may run the
BIOS Setup when you start up the computer. Please press <F2> during the Power-
On-Self-Test (POST) to enter the BIOS Setup Utility, otherwise, POST will continue
with its test routines.
If you wish to enter the BIOS Setup after POST, restart the system by pressing
<Ctl> + <Alt> + <Delete>, or by pressing the reset button on the system chassis.
You may also restart the system by turning the system off and then back on.
The BIOS Setup Utility is designed to be user-friendly. It is a menu-driven program,
which allows you to scroll through its various sub-menus and select among the
predetermined choices.

Because the BIOS software is constantly being updated, the

following BIOS setup screens and descriptions are for reference
purpose only, and may not exactly match what you see on your
screen.

3.1.1 BIOS Menu Bar

The top of the screen has a menu bar with the following selections:
MAIN Sets up the basic system configuration
ADVANCED Sets up the advanced features
SECURITY Sets up the security features
POWER Configures Power Management features
BOOT Configures the default system device that is used
to locate and load the Operating System
EXIT Exits the current menu or the BIOS Setup

To access the menu bar items, press the right or left arrow key on the keyboard
until the desired item is highlighted.

3.1.2 Legend Bar

At the bottom of the Setup Screen is a legend bar. The following table lists the keys
in the legend bar with their corresponding functions.

17
Navigation Key(s) Function Description
<F1> Displays the General Help Screen
<ESC> Jumps to the Exit menu or returns to the upper menu
from the current menu
/ Moves cursor up or down between fields
/ Selects menu to the left or right
+ / - Increases or decreases values
<Enter> Brings up a selected menu for a highlighted field
<F9> Loads all the setup items to default value
<F10> Saves changes and exits Setup

3.2 Main Menu

When you enter the BIOS Setup Utility, the following screen appears.

AMIBIOS SETUP UTILITY - VERSION 3.31a

Main Advanced Security Power Boot Exit
[ Setup Help ]
System Date Oct 31 2003 Fri
System Time 20:07:40 Month: Jan - Dec
Day: 01 - 31
Floppy Drives Year: 1980 - 2099
IDE Devices

BIOS Version K7VT4A+ BIOS P1.00

Processor Type AMD Athlon(tm) XP 2600+
Processor Speed 2133 MHz
L1 Cache Size 128 KB
L2 Cache Size 256 KB
Total Memory 512 MB
DDR1 512 MB / 200 MHz (DDR400)
DDR2 None

F1:Help :Select Item +/-:Change Values F9:Setup Defaults

Esc:Exit :Select Menu Enter:Select Sub-Menu F10:Save & Exit

System Date [Month/Day/Year]

Set the system date that you specify. Valid values for month, day, and year are
Month: (Jan to Dec), Day: (1 to 31), Year: (up to 2099). Use keys to move
between the Month, Day, and Year fields.
System Time [Hour:Minute:Second]
Set the system to the time that you specify. Use keys to move between
the Hour, Minute, and Second fields.
Floppy Drives
Use this to set the type of floppy drives installed.
IDE Devices
Use this to configure IDE devices.

18
TYPE
To set the type of the IDE device, first, please select “IDE Devices” on Main
menu and press <Enter> to get into the sub-menu. Then, select among
“Primary IDE Master”, “Primary IDE Slave”, “Secondary IDE Master”, and
“Secondary IDE Slave” to make configuration of its type. Below are the
configuration options.

AMIBIOS SETUP UTILITY - VERSION 3.31a

Main
Primary IDE Master [ Setup Help ]

Select how to set the

Type Auto parameters of drive,
Cylinders
Heads Or
Write Precompensation Select [AUTO] to set
Sectors all HDD parameters
Maximum Capacity automatically.
LBA Mode Off
Block Mode Off
Fast Programmed I/O Modes Auto
32 Bit Transfer Mode Off
Ultra DMA Mode Auto

F1:Help :Select Item +/-:Change Values F9:Setup Defaults

Esc:Previous Menu Enter:Select Sub-Menu F10:Save & Exit

[USER]: It allows user to manually enter the number of cylinders, heads,

and sectors per track for the drive.

Before attempting to configure a hard disk drive, make sure you

have the correct configuration information supplied by the drive
manufacturer. Incorrect settings may cause the system to fail
to recognize the installed hard disk.

[Auto]: Select [Auto] to automatically detect hard disk drive. If auto-

detection is successful, the BIOS Setup automatically fills in the
correct values for the remaining fields on this sub-menu. If the auto-
detection fails, it may due to that the hard disk is too old or too new.
If the hard disk was already formatted on an older system, the BIOS
Setup may detect incorrect parameters. In these cases, select [User]
to manually enter the IDE hard disk drive parameters.

After entering the hard disk information into BIOS, use a disk utility,
such as FDISK, to partition and format the new IDE hard disk
drives. This is necessary so that you can write the data into or
read the data from the installed hard disk. Please make sure to set
the partition of the Primary IDE hard disk drives to make them
active.

19
 [CD/DVD]: This is used for IDE CD/DVD drives.
[ARMD]: This is used for IDE ARMD (ATAPI Removable Media Device),
such as MO.
Cylinders
This is used to configure the number of cylinders. Refer to the drive
documentation to determine the correct value.
Heads
This is used to configure the number of read/write heads. Refer to the
drive documentation to determine the correct values.
Write Pre-compensation
Enter Write Pre-compensation sector. Refer to the drive documentation to
determine the correct value.
Sectors
This is used to configure the number of sectors per track. Refer to the
drive documentation to determine the correct value.
Maximum Capacity
This field shows the drive’s maximum capacity as calculated by the BIOS
based on the drive information you entered.
LBA Mode
This allows user to select the LBA mode for a hard disk > 512 MB under
DOS and Windows; for Netware and UNIX user, select [Off] to disable the
LBA mode.
Block Mode
Set the block mode to [On] will enhance hard disk performance by reading
or writing more data during each transfer.
Fast Programmed I/O Modes
This allows user to set the PIO mode to enhance hard disk performance by
optimizing the hard disk timing.
32 Bit Transfer Mode
It allows user to enable 32-bit access to maximize the IDE hard disk data
transfer rate.
Ultra DMA Mode
Ultra DMA capability allows improved transfer speeds and data integrity
for compatible IDE devices. Set to [Disabled] to suppress Ultra DMA
capability.

3.3 Advanced, Security, Power, Boot, and Exit Menus

Detailed descriptions of these menus are listed in the Appendix. See page 22.

20
4. Software Support
4.1 Install Operating System
This motherboard supports various Microsoft® Windows® operating systems:
98 SE / ME / 2000 / XP. Because motherboard settings and hardware options vary,
use the setup procedures in this chapter for general reference only. Refer to your
OS documentation for more information.

4.2 Support CD Information

The Support CD that came with the motherboard contains necessary drivers and
useful utilities that will enhance the motherboard features.

4.2.1 Running The Support CD

To begin using the support CD, insert the CD into your CD-ROM drive. The CD
automatically displays the Main Menu if “AUTORUN” is enabled in your computer.
If the Main Menu did not appear automatically, locate and double click on the file
ASSETUP.EXE from the BIN folder in the Support CD to display the menus.

4.2.2 Drivers Menu

The Drivers Menu shows the available devices drivers if the system detects
installed devices. Install the necessary drivers to activate the devices.

4.2.3 Utilities Menu

The Utilities Menu shows the applications software that the motherboard
supports. Click on a specific item then follow the installation wizard to install it.

4.2.4 ASRock PC-DIY Live Demo Program

ASRock presents you a multimedia PC-DIY live demo, which shows you how to
install your own PC system step by step. You may find the file through the
following path:
..\ MPEGAV \ AVSEQ01.DAT
To see this demo program, you may run Microsoft® Media Player® to play the file.

4.2.5 Contact Information

If you need to contact ASRock or want to know more about ASRock, welcome
to visit ASRock’s website at http://www.asrock.com; or you may contact your
dealer for further information.

21
Appendix: Advanced BIOS Setup
This section will introduce you the following BIOS Setup menus: “Advanced,”
“Security,” “Power,” “Boot,” and “Exit.”

1. Advanced BIOS Setup Menu

AMIBIOS SETUP UTILITY - VERSION 3.31a

Main Advanced Security Power Boot Exit
[ Setup Help ]
Spread Spectrum Disabled
CPU Host Frequency Auto <Enter> to enable or
Actual Frequency 133MHz disable the feature of
DRAM Frequency Auto spread spectrum.
Flexibility Option Disabled

Chipset Configuration
Resource Configuration
Peripheral Configuration
System Hardware Monitor

F1:Help :Select Item +/-:Change Values F9:Setup Defaults

Esc:Exit :Select Menu Enter:Select Sub-Menu F10:Save & Exit

Spread Spectrum
This field should always be [Disabled] for better system stability.
CPU Host Frequency
[Auto]
It is recommended to select this option, which will let the CPU host frequency of
this motherboard determined by the jumper-setting.
[Manual]
This allows user to set CPU host frequency manually. However, because the
CPU host frequency of this motherboard is determined by the jumper-setting,
you must set the FSB jumper adjustment according to your AMD CPU before you
use this “Manual” option as the FSB setting in BIOS setup to perform over
clocking. This is not recommended unless you thoroughly know the feature.
Wrong setup may cause problems during operation.
DRAM Frequency
If set to [Auto], the motherboard will detect the inserted memory module(s) and
automatically assign appropriate frequency. You may select other value as
operating frequency: [133MHz (DDR266)], [166MHz (DDR333)],
[200MHz (DDR400)].
Flexibility Option
The default value of this option is [Disabled]. It will allow better tolerance for
memory compatibility when it is set to [Enabled].

22
Chipset Configuration
AMIBIOS SETUP UTILITY - VERSION 3.31a
Advanced

Chipset Configuration [ Setup Help ]

<Enter> to select [4X],

AGP Mode Auto [2X], [1X] as the AGP
AGP Aperture Size 64MB mode.
AGP Fast Write Disabled
PCI Delay Transaction Disabled

USB Controller Enabled

USB Device Legacy Support Disabled

DRAM CAS# Latency Auto

Over Vcore Voltage Disabled

V-Link Speed Normal

F1:Help :Select Item +/-:Change Values F9:Setup Defaults

Esc:Previous Menu Enter:Select Sub-Menu F10:Save & Exit

AGP Mode
This feature will be set to [Auto] as default.
AGP Aperture Size
It refers to a section of the PCI memory address range used for graphics
memory. It is recommended to leave this field at the default value unless the
installed AGP card’s specifications requires other sizes.
AGP Fast Write
This allows you to enable or disable the feature of AGP fast write protocol
support.
PCI Delay Transaction
Enable PCI Delay Transaction feature will free the PCI Bus when the CPU is
accessing 8-bit ISA cards. Disable this feature when using ISA cards that are
not PCI 2.1 compliant.
USB Controller
Use this to enable or disable the use of USB controller.
USB Device Legacy Support
Use this to enable or disable the support to emulate legacy I/O devices such as
mouse, keyboard,... etc.
DRAM CAS# Latency
This is used to adjust the means of memory accessing. Configuration options:
[Auto], [2T], [2.5T], [3T]. Please note that not all the DDR DIMMs can support CAS
latency=3T.

23
Over Vcore Voltage
This feature allows you to increase the CPU Vcore voltage with two levels. The
default value is [Disabled].

It is not recommended to enable “Over Vcore Voltage” feature. Doing so

may cause CPU damage.

V-Link Speed
This feature allows you to speed up the V-Link speed. The default value is
[Normal].

Resource Configuration
AMIBIOS SETUP UTILITY - VERSION 3.31a
Advanced

Resource Configuration [ Setup Help ]

<Enter> to select PCI

PCI Latency Timer (PCI Clocks) 32 clocks. Leave on
Primary Graphics Adapter PCI default setting for the
best PCI performance.

F1:Help :Select Item +/-:Change Values F9:Setup Defaults

Esc:Previous Menu Enter:Select Sub-Menu F10:Save & Exit

PCI Latency Timer (PCI Clocks)

The default is 32. It is recommended to keep the default value unless the in-
stalled PCI expansion cards’ specifications require other settings.
Primary Graphics Adapter
Select PCI or AGP as the primary graphics adapter.

24
Peripheral Configuration
AMIBIOS SETUP UTILITY - VERSION 3.31a
Advanced

Peripheral Configuration [ Setup Help ]

<Enter> to enable or
OnBoard FDC Auto disable the floppy
OnBoard Serial Port Auto drive controller.
OnBoard Infrared Port Disabled
OnBoard Parallel Port Auto
Parallel Port Mode ECP+EPP
EPP Version 1.9
Parallel Port IRQ Auto
Parallel Port DMA Channel Auto
OnBoard Midi Port Disabled
Midi IRQ Select 5
OnBoard Game Port 200h
OnBoard IDE Both
OnBoard LAN Enabled
OnBoard AC' 97 Audio Auto

F1:Help :Select Item +/-:Change Values F9:Setup Defaults

Esc:Previous Menu Enter:Select Sub-Menu F10:Save & Exit

OnBoard FDC
Use this to enable or disable floppy drive controller.
OnBoard Serial Port
Use this to set addresses for the onboard serial ports or disable serial ports.
Configuration options: [Auto], [Disabled], [3F8 / IRQ4 / COM1],
[2F8 / IRQ3 / COM2], [3E8 / IRQ4 / COM3], [2E8 / IRQ3 / COM4].
OnBoard Infrared Port
You may select [Auto] or [Disabled] for this onboard infrared port feature.
OnBoard Parallel Port
Select Parallel Port address or disable Parallel Port. Configuration options: [Auto],
[Disabled], [378], [278].
Parallel Port Mode
Set the operation mode of the parallel port. The default value is [ECP+EPP]. If
this option is set to [ECP+EPP], it will show the EPP version in the following
item, “EPP Version”.
OnBoard Midi Port
Select address for Midi Port or disable Midi Port. Configuration options: [Disabled],
[330], [300], [290], [292].
Midi IRQ Select
Use this to select Midi IRQ. Configuration options: [3], [4], [5], [7], [10], [11].
OnBoard Game Port
Select address for Game Port or disable Game Port. Configuration options:
[Disabled], [200h], [208h].

25
OnBoard IDE
You may enable either the primary IDE channel or the secondary IDE channel. Or
you may enable both the primary and the secondary IDE channels by selecting
[Both]. Set to [Disabled] will disable the both. Configuration options: [Disabled],
[Primary], [Secondary], [Both].
OnBoard LAN
This allows you to enable or disable the onboard LAN feature.
OnBoard AC’97 Audio
Select [Disabled], [Auto] or [Enabled] for the onboard AC’97 Audio feature.

System Hardware Monitor

You may check the status of the hardware on your system. It allows you to
monitor the parameters for CPU temperature, Motherboard temperature, CPU
fan speed, and critical voltage.

AMIBIOS SETUP UTILITY - VERSION 3.31a

Advanced

System Hardware Monitor [ Setup Help ]

CPU Temperature 35 C / 95 F
M / B Temperature 27 C / 82 F
CPU FAN Speed 3110 RPM
Chassis FAN Speed 0 RPM
Vcore 1.72 V
+ 3.30V 3.31 V
+ 5.00V 4.97 V
+ 12.00V 12.16 V

F1:Help :Select Item +/-:Change Values F9:Setup Defaults

Esc:Previous Menu Enter:Select Sub-Menu F10:Save & Exit

26
2. Security Setup Menu
AMIBIOS SETUP UTILITY - VERSION 3.31a
Main Advanced Security Power Boot Exit
[ Setup Help ]
Supervisor Password Clear
User Password Clear <Enter> to set the
supervisor password.
Set Supervisor Password [ Enter ]
Set User Password [ Enter ]

Password Check Setup

F1:Help :Select Item +/-:Change Values F9:Setup Defaults

Esc:Exit :Select Menu Enter:Select Sub-Menu F10:Save & Exit

Supervisor Password: This field shows the status of the Supervisor Password.
[Clear]: No password has been set.
[Set]: Supervisor password has been set.
User Password: This field shows the status of the User Password.
[Clear]: No password has been set.
[Set]: User password has been set.
Set Supervisor Password: Press <Enter> to set the Supervisor Password. Valid
password can be a 1 to 6 alphanumeric characters combination. If you already
have a password, you need to enter your current password first in order to
create a new password.
Set User Password: Press <Enter> to set the User Password. Valid password can
be a 1 to 6 alphanumeric characters combination. If you already have a
password, you need to enter your current password first in order to create a
new password.
Password Check: Select the check point for “Password Check”. Configuration
options: [Setup], [Always]. If [Setup] option is selected, the “Password Check”
is performed before BIOS setup. If [Always] option is selected, the “Password
Check” is performed before both boot-up and BIOS setup.

27
3. Power Setup Menu
AMIBIOS SETUP UTILITY - VERSION 3.31a
Main Advanced Security Power Boot Exit
[ Setup Help ]
Suspend To RAM Disabled
Repost Video on STR Resume Disabled
Restore on AC / Power Loss Power Off <Enter> to select
Ring-In Power On Disabled auto-detect or disable
PCI Devices Power On Disabled the Suspend-to-RAM
PS / 2 Keyboard Power On Disabled feature.
RTC Alarm Power On Disabled
RTC Alarm Date Every Day
RTC Alarm Hour 12
RTC Alarm Minute 30
RTC Alarm Second 30

F1:Help :Select Item +/-:Change Values F9:Setup Defaults

Esc:Exit :Select Menu Enter:Select Sub-Menu F10:Save & Exit

Suspend to RAM
This field allows you to select whether to auto-detect or disable the Suspend-
to-RAM feature. Select [Auto] will enable this feature if the system supports it.
Repost Video on STR Resume
This feature allows you to repost video on STR resume. It is recommended to
enable this feature under Microsoft® Windows ® 98 / ME.
Restore on AC/Power Loss
This allows you to set the power state after an unexpected AC/power loss. If
[Power Off] is selected, the AC/power remains off when the power recovers.
If [Power On] is selected, the AC/power resumes and the system starts to boot
up when the power recovers.
Ring-In Power On
Use this to enable or disable Ring-in signals to turn on the system from the
power-soft-off mode.
PCI Devices Power On
Use this to enable or disable PCI devices to turn on the system from the power-
soft-off mode.
PS/2 Keyboard Power On
Use this to enable or disable PS/2 keyboard to turn on the system from the
power-soft-off mode.
RTC Alarm Power On
Use this to enable or disable RTC (Real Time Clock) to power on the system. If
[Enable] is selected, you must fill the RTC Alarm Date / Hour / Minute / Second
sub-fields with the actual wake up time you desire.

28
4. Boot Setup Menu
AMIBIOS SETUP UTILITY - VERSION 3.31a
Main Advanced Security Power Boot Exit
[ Setup Help ]
Quick Boot Mode Enabled
Boot Up Num-Lock On <Enter> to enable or
Boot To OS/2 No disable the quick boot
Boot From Network Disabled mode.

Boot Device Priority

F1:Help :Select Item +/-:Change Values F9:Setup Defaults

Esc:Exit :Select Menu Enter:Select Sub-Menu F10:Save & Exit

Quick Boot Mode

Enable this mode will speed up the boot-up routine by skipping memory retestings.
Boot Up Num-Lock
If this is enabled, it will automatically activate the Numeric Lock function after
boot-up.
Boot To OS/2
This enables boot-up to OS/2 operating system.
Boot From Network
Use this to enable or disable “boot from network” feature.
Boot Device Priority
This allows you to set the boot device priority.

29
5. Exit Menu
AMIBIOS SETUP UTILITY - VERSION 3.31a
Main Advanced Security Power Boot Exit
[ Setup Help ]
Exit Saving Changes [ Enter ]
Exit Discarding Changes [ Enter ] Exits and saves the
Load Default Settings [ Enter ] changes in CMOS RAM.
Discard Changes [ Enter ]

F1:Help :Select Item +/-:Change Values F9:Setup Defaults

Esc:Exit :Select Menu Enter:Select Sub-Menu F10:Save & Exit

Exit Saving Changes

After you enter the sub-menu, the message “Save current settings and exit” will
appear. If you press <ENTER>, it will save the current settings and exit the BIOS
SETUP Utility.
Exit Discarding Changes
After you enter the submenu, the message “Quit without saving changes” will
appear. If you press <ENTER>, you will exit the BIOS Setup Utility without making
any changes to the settings.
Load Default Settings
After you enter the submenu, the message “Load default settings” will appear.
If you press <Enter>, it will load the default values for all the setup configuration.
Discard Changes
After you enter the sub-menu, the message “Load setup original values” will
appear. If you press <ENTER>, original values will be restored and all changes
are discarded.

30