Scribd
Upload
27 views

Premier Quatro Addressable System Network: Features

The Quatro system network allows fire alarm systems to communicate across a large site using a peer-to-peer network without a master panel. The network can connect up to 64 nodes across 64km of cable to monitor, control, and distribute alarm signals. Each node operates independently but can communicate with all other nodes on the network and function autonomously if the network fails. The network communication occurs over a single pair of wires and uses RS-485 protocol.

Uploaded by

mota
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
27 views

Premier Quatro Addressable System Network: Features

The Quatro system network allows fire alarm systems to communicate across a large site using a peer-to-peer network without a master panel. The network can connect up to 64 nodes across 64km of cable to monitor, control, and distribute alarm signals. Each node operates independently but can communicate with all other nodes on the network and function autonomously if the network fails. The network communication occurs over a single pair of wires and uses RS-485 protocol.

Uploaded by

mota
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Premier Quatro Addressable System Network

The Quatro system network has the facility to


monitor, indicate and control the functions of a Features
fire alarm installation, thus allowing signals to Peer-to-Peer network wide communication
be distributed around a large site.
Network together:-
The network operates as a global communication system Premier Quatro panels
and does not require a master panel or computer. This Network repeaters
approach reduces cost and no single panel/equipment Up to 64 panels or 256 loops may be networked
failure will disable the entire system. together

Each item of equipment connected to the network


is referred to as a node. Up to 64 nodes may be
connected. QT-NC
Each node is programmed independently to listen to all This network card provides the
the nodes, or to a single node on the network following:

The network uses RS 485 data communication. Up to RS 485 repeater output


a total network cable length of 64km is possible. All Serial port for either panel printer or external printer
panels will continue to function in stand-alone mode, (desk top)
even if the network fails. RS 485 network connection for use with
standard network data cable
The operation of the network is such that each node
has total stand alone capability in that its local QT-NC/FP
operation is not directly affected by its connection
This network card provides network connection
to or disconnection from the network. The ability of
for use with fibre-optic multi-mode. No printer
a local control panel to observe events means that it or repeater out is available with this card.
can be programmed to respond to events elsewhere on
the network. The effect of this capability is that any
control panel is able to respond to any sensor device
connected anywhere on the network. This provides a
possible effective 256 loop control panel distributed
around a single site as a number of smaller units.
Network repeater panels provide the ability to observe
and control elements of the network via a compact unit
which may be conveniently mounted at manned control
points and still provide all essential display and control
facilities.

Network communication takes place over a single pair of


wires providing a link to all nodes.

Doc No. GLT-215-6-2 Issue No. 001 Date: 03/09/2013


Typical Network Loop

Node 48 Node 24
Node 32

QT/REP
QT/1+100 QT/1

Node 14
Node 64

64 Nodes
QT/1+100P
QT/1+P

Node 1
Node 2

QT/REP
QT/1

Data Cable (Max 10,000m)

Maximum distance between nodes = 1000m

Doc No. GLT-215-6-2 Issue No. 001 Date: 03/09/2013


Gateway Network Card
(QT-GNC)

Further to the network described on page 8, a


QT-GNC (special Gateway card) can be used on
any ONE Quatro panel (stand alone or part of a
network) to provide the facility of connecting
that stand alone panel and/or the network
through a LAN connection to provide TCP-IP
remote viewing on HTM for the last 64 events
in that stand alone panel or network.

Internet

LAN

QT/GNC PC Workstation

Doc No. GLT-215-6-2 Issue No. 001 Date: 03/09/2013

You might also like