c






  
 

Jump to: navigation, search

A light dependent resistor

The internal components of a photoelectric control for a typical American streetlight. The
photoresistor is facing rightwards, and controls whether current flows through the heater which
opens the main power contacts. At night, the heater cools, closing the power contacts, energizing
the street light. The heater/bimetal mechanism provides a built-in time-delay.

A 


 or    
 or      is a resistor whose

resistance decreases with increasing incident light intensity. It can also be referenced as a



 
.

A photoresistor is made of a high resistance semiconductor. If light falling on the device is of

high enough frequency, photons absorbed by the semiconductor give bound electrons enough
energy to jump into the conduction band. The resulting free electron (and its hole partner)
conduct electricity, thereby lowering resistance.

A photoelectric device can be either intrinsic or extrinsic. An intrinsic semiconductor has its own
charge carriers and is not an efficient semiconductor, e.g. silicon. In intrinsic devices the only
available electrons are in the valence band, and hence the photon must have enough energy to
excite the electron across the entire bandgap. Extrinsic devices have impurities, also called
dopants, added whose ground state energy is closer to the conduction band; since the electrons
do not have as far to jump, lower energy photons (i.e., longer wavelengths and lower
frequencies) are sufficient to trigger the device. If a sample of silicon has some of its atoms
replaced by phosphorus atoms (impurities), there will be extra electrons available for conduction.
This is an example of an extrinsic semiconductor.

 

Photoresistors come in many different types. Inexpensive cadmium sulfide cells can be found in
many consumer items such as camera light meters, street lights, clock radios, alarms, and
outdoor clocks.

They are also used in some dynamic compressors together with a small incandescent lamp or
light emitting diode to control gain reduction.

Lead sulfide and indium antimonide LDRs are used for the mid infrared spectral region. Ge:Cu
photoconductors are among the best far-infrared detectors available, and are used for infrared
astronomy and infrared spectroscopy.

Transducers are used for changing energy types.

Below is a symbol for a photoresistor as used in some circuit diagram.File:Light Dependent

Resistor Symbol.jpg 
=   



  
 

Jump to: navigation, search

"LED" redirects here. For other uses, see LED (disambiguation).

For various types of outdoor LED based displays, see LED display.

=
  



Red, green and blue LEDs of the 5mm type

  Passive, optoelectronic


 
    Electroluminescence

  Nick Holonyak Jr. (1962)


 


 


 Anode and Cathode

A    
 (=
) (pronounced / Ñli di /[1], or just /lÑd/), is an electronic light
source. The first LED was built in the 1920s by Oleg Vladimirovich Losev, a radio technician
who noticed that diodes used in radio receivers emitted light when current was passed through
them. The LED was introduced as a practical electronic component in 1962.
All early devices emitted low-intensity red light, but modern LEDs are available across the
visible, ultraviolet and infra red wavelengths, with very high brightness.

LEDs are based on the semiconductor diode. When the diode is forward biased (switched on),
electrons are able to recombine with holes and energy is released in the form of light. This effect
is called electroluminescence and the color of the light is determined by the energy gap of the
semiconductor. The LED is usually small in area (less than 1 mm2) with integrated optical
components to shape its radiation pattern and assist in reflection.[2]

LEDs present many advantages over traditional light sources including lower energy
consumption, longer lifetime, improved robustness, smaller size and faster switching. However,
they are relatively expensive and require more precise current and heat management than
traditional light sources.

Applications of LEDs are diverse. They are used as low-energy indicators but also for
replacements for traditional light sources in general lighting and automotive lighting. The
compact size of LEDs has allowed new text and video displays and sensors to be developed,
while their high switching rates are useful in communications technology.


  

Green electroluminescence from a point contact on a crystal of SiC recreates H. J. Round's original
experiment from 1907.

Electroluminescence was discovered in 1907 by the British experimenter H. J. Round of Marconi

Labs, using a crystal of silicon carbide and a cat's-whisker detector.[3] [4] Russian Oleg
Vladimirovich Losev independently created the first LED in the mid 1920s; his research was
distributed in Russian, German and British scientific journals,[5] but no practical use was made of
the discovery for several decades. Rubin Braunstein of the Radio Corporation of America
reported on infrared emission from gallium arsenide (GaAs) and other semiconductor alloys in
1955.[6] Braunstein observed infrared emission generated by simple diode structures using
gallium antimonide (GaSb), GaAs, indium phosphide (InP), and silicon-germanium (SiGe)
alloys at room temperature and at 77 kelvin.
In 1961, experimenters Robert Biard and Gary Pittman working at Texas Instruments,[7] found
that GaAs emitted infrared radiation when electric current was applied and received the patent
for the infrared LED.

The first practical visible-spectrum (red) LED was developed in 1962 by Nick Holonyak Jr.,
while working at General Electric Company.[8] Holonyak is seen as the "father of the light-
emitting diode".[9] M. George Craford[10], a former graduate student of Holonyak, invented the
first yellow LED and improved the brightness of red and red-orange LEDs by a factor of ten in
1972.[11] In 1976, T.P. Pearsall created the first high-brightness, high efficiency LEDs for optical
fiber telecommunications by inventing new semiconductor materials specifically adapted to
optical fiber transmission wavelengths.[12]

Up to 1968 visible and infrared LEDs were extremely costly, on the order of US $200 per unit,
and so had little practical application.[13] The Monsanto Company was the first organization to
mass-produce visible LEDs, using gallium arsenide phosphide in 1968 to produce red LEDs
suitable for indicators.[13] Hewlett Packard (HP) introduced LEDs in 1968, initially using GaAsP
supplied by Monsanto. The technology proved to have major applications for alphanumeric
displays and was integrated into HP's early handheld calculators.

c

Red, yellow and green (unlit) LEDs used in a traffic signal.

The first commercial LEDs were commonly used as replacements for incandescent indicators,
and in seven-segment displays,[14] first in expensive equipment such as laboratory and electronics
test equipment, then later in such appliances as TVs, radios, telephones, calculators, and even
watches (see list of signal applications). These red LEDs were bright enough only for use as
indicators, as the light output was not enough to illuminate an area. Later, other colors became
widely available and also appeared in appliances and equipment. As the LED materials
technology became more advanced, the light output was increased, while maintaining the
efficiency and the reliability to an acceptable level. The invention and development of the high
power white light LED led to use for illumination[15] [16] (see list of illumination applications).
Most LEDs were made in the very common 5 mm T1¾ and 3 mm T1 packages, but with
increasing power output, it has become increasingly necessary to shed excess heat in order to
maintain reliability[17], so more complex packages have been adapted for efficient heat
dissipation. Packages for state-of-the-art high power LEDs bear little resemblance to early LEDs.

 
 
 

Illustration of Haitz's Law. Light output per LED as a function of time, note the logarithmic scale on the
vertical axis.

The first high-brightness blue LED was demonstrated by Shuji Nakamura of Nichia Corporation
and was based on InGaN borrowing on critical developments in GaN nucleation on sapphire
substrates and the demonstration of p-type doping of GaN which were developed by Isamu
Akasaki and H. Amano in Nagoya. In 1995, Alberto Barbieri at the Cardiff University
Laboratory (GB) investigated the efficiency and reliability of high-brightness LEDs and
demonstrated a very impressive result by using a transparent contact made of indium tin oxide
(ITO) on (AlGaInP/GaAs) LED. The existence of blue LEDs and high efficiency LEDs quickly
led to the development of the first white LED, which employed a Y3Al5 O12:Ce, or "YAG",
phosphor coating to mix yellow (down-converted) light with blue to produce light that appears
white. Nakamura was awarded the 2006 Millennium Technology Prize for his invention.[18]

The development of LED technology has caused their efficiency and light output to increase
exponentially, with a doubling occurring about every 36 months since the 1960s, in a way
similar to Moore's law. The advances are generally attributed to the parallel development of
other semiconductor technologies and advances in optics and material science. This trend is
normally called Haitz's Law after Dr. Roland Haitz. [19]

In February 2008, Bilkent university in Turkey reported 300 lumens of visible light per watt
luminous efficacy (not per electrical watt) and warm light by using nanocrystals [20].

In January 2009, researchers from Cambridge University reported a process for growing gallium
nitride (GaN) LEDs on silicon. Production costs could be reduced by 90% using six-inch silicon
wafers instead of two-inch sapphire wafers. The team was led by Colin Humphreys.[21]

   


Parts of an LED

The inner workings of an LED

I-V diagram for a diode an LED will begin to emit light when the on-voltage is exceeded. Typical on
voltages are 2-3 Volt

 c 

Like a normal diode, the LED consists of a chip of semiconducting material impregnated, or
÷
÷, with impurities to create a

. As in other diodes, current flows easily from the
p-side, or anode, to the n-side, or cathode, but not in the reverse direction. Charge-carriers²
electrons and holes²flow into the junction from electrodes with different voltages. When an
electron meets a hole, it falls into a lower energy level, and releases energy in the form of a
photon.

The wavelength of the light emitted, and therefore its color, depends on the band gap energy of
the materials forming the

. In silicon or germanium diodes, the electrons and holes
recombine by a  ÷

 

 which produces no optical emission, because these are
indirect band gap materials. The materials used for the LED have a direct band gap with energies
corresponding to near-infrared, visible or near-ultraviolet light.

LED development began with infrared and red devices made with gallium arsenide. Advances in
materials science have made possible the production of devices with ever-shorter wavelengths,
producing light in a variety of colors.

LEDs are usually built on an n-type substrate, with an electrode attached to the p-type layer
deposited on its surface. P-type substrates, while less common, occur as well. Many commercial
LEDs, especially GaN/InGaN, also use sapphire substrate.

Most materials used for LED production have very high refractive indices. This means that much
light will be reflected back in to the material at the material/air surface interface. Therefore 
 
 

 is an important aspect of LED production, subject to much research and
development.

 

 

Typical indicator LEDs are designed to operate with no more than 30±60 milliwatts [mW] of
electrical power. Around 1999, Philips Lumileds introduced power LEDs capable of continuous
use at one watt [W]. These LEDs used much larger semiconductor die sizes to handle the large
power inputs. Also, the semiconductor dies were mounted onto metal slugs to allow for heat
removal from the LED die.

One of the key advantages of LED-based lighting is its high efficiency, as measured by its light
output per unit power input. White LEDs quickly matched and overtook the efficiency of
standard incandescent lighting systems. In 2002, Lumileds made five-watt LEDs available with a
luminous efficacy of 18±22 lumens per watt [lm/W]. For comparison, a conventional 60±100 W
incandescent lightbulb produces around 15 lm/W, and standard fluorescent lights produce up to
100 lm/W. A recurring problem is that efficiency will fall dramatically for increased current.
This effect is known as droop and effectively limits the light output of a given LED, increasing
heating more than light output for increased current.

In September 2003, a new type of blue LED was demonstrated by the company Cree, Inc. to
provide 24 mW at 20 milliamperes [mA]. This produced a commercially packaged white light
giving 65 lm/W at 20 mA, becoming the brightest white LED commercially available at the time,
and more than four times as efficient as standard incandescents. In 2006 they demonstrated a
prototype with a record white LED luminous efficacy of 131 lm/W at 20 mA. Also, Seoul
Semiconductor has plans for 135 lm/W by 2007 and 145 lm/W by 2008, which would be
approaching an order of magnitude improvement over standard incandescents and better even
than standard fluorescents.[22] Nichia Corporation has developed a white LED with luminous
efficiency of 150 lm/W at a forward current of 20 mA.[23]

It should be noted that high-power (• 1 W) LEDs are necessary for practical general lighting
applications. Typical operating currents for these devices begin at 350 mA. The highest
efficiency high-power white LED is claimed[24] by Philips Lumileds Lighting Co. with a
luminous efficacy of 115 lm/W (350 mA).

Note that these efficiencies are for the LED chip only, held at low temperature in a lab. In a
lighting application, operating at higher temperature and with drive circuit losses, efficiencies are
much lower. DOE testing of commercial LED lamps designed to replace incandescent or CFL
lamps showed that average efficacy was still about 31 lm/W in 2008 (tested performance ranged
from 4 lm/W to 62 lm/W)[25].

Cree issued a press release on November 19, 2008 about a laboratory prototype LED achieving
161 lumens/watt at room temperature. The total output was 173 lumens, and the correlated color
temperature was reported to be 4689 K.[26][
 ]

 =  

Dain article: List of LED failure modes

Solid state devices such as LEDs are subject to very limited wear and tear if operated at low
currents and at low temperatures. Many of the LEDs produced in the 1970s and 1980s are still in
service today. Typical lifetimes quoted are 25000 to 100000 hours but heat and current settings
can extend or shorten this time significantly. [27]

The most common symptom of LED (and diode laser) failure is the gradual lowering of light
output and loss of efficiency. Sudden failures, although rare, can occur as well. Early red LEDs
were notable for their short lifetime. With the development of high power LEDs the devices are
subjected to higher junction temperatures and higher current densities than traditional devices.
This causes stress on the material and may cause early light output degradation. To quantitatively
classify lifetime in a standardized manner it has been suggested to use the terms L75 and L50
which is the time it will take a given LED to reach 75% and 50% light output respectively.[28]
L50 is equivalent to the half-life of the LED.

 

  

Illustration of Haitz's Law. Light output per LED as a function of time, note the logarithmic scale on the
vertical axis.
Parts of an LED

The inner workings of an LED

I-V diagram for a diode an LED will begin to emit light when the on-voltage is exceeded. Typical on
voltages are 2-3 Volt

 c 



  
Conventional LEDs are made from a variety of inorganic semiconductor materials, the following
table shows the available colors with wavelength range, voltage drop and material:





 

  
 
! 



Gallium arsenide (GaAs)

Infrared ʄ > 760 ȴV < 1.9
Aluminium gallium arsenide (AlGaAs)

Aluminium gallium arsenide (AlGaAs)

1.63 < ȴV < Gallium arsenide phosphide (GaAsP)
Red 610 < ʄ < 760
2.03 Aluminium gallium indium phosphide (AlGaInP)
Gallium(III) phosphide (GaP)

Gallium arsenide phosphide (GaAsP)

2.03 < ȴV <
Orange 590 < ʄ < 610 Aluminium gallium indium phosphide (AlGaInP)
2.10
Gallium(III) phosphide (GaP)

Gallium arsenide phosphide (GaAsP)

2.10 < ȴV <
Yellow 570 < ʄ < 590 Aluminium gallium indium phosphide (AlGaInP)
2.18
Gallium(III) phosphide (GaP)

Green 500 < ʄ < 570 1.9[29] < ȴV < Indium gallium nitride (InGaN) / Gallium(III) nitride (GaN)
 r.0 Gallium(III) phosphide (GaP)
Aluminium gallium indium phosphide (AlGaInP)
Aluminium gallium phosphide (AlGaP)

Zinc selenide (ZnSe)

2.r8 < ȴV < Indium gallium nitride (InGaN)
Blue r50 < ʄ < 500
3.7 Silicon carbide (SiC) as substrate
Silicon (Si) as substrate Ͷ (under development)

2.76 < ȴV <

Violet r00 < ʄ < r50 Indium gallium nitride (InGaN)
r.0

Dual blue/red LEDs,

2.r8 < ȴV <
Purple multiple types blue with red phosphor,
3.7
or white with purple plastic

diamond (C)
Aluminium nitride (AlN)
Ultraviolet ʄ < r00 3.1 < ȴV < r.r Aluminium gallium nitride (AlGaN)
Aluminium gallium indium nitride (AlGaInN) Ͷ (down to
210 nm)[30]

White Broad spectrum ȴV = 3.5 Blue/UV diode with yellow phosphor

 !
 "=


Blue LEDs.
Blue LEDs are based on the wide band gap semiconductors GaN (gallium nitride) and InGaN
(indium gallium nitride). They can be added to existing red and green LEDs to produce the
impression of white light, though white LEDs today rarely use this principle.

The first blue LEDs were made in 1971 by Jacques Pankove (inventor of the gallium nitride
LED) at RCA Laboratories.[31] However, these devices had too little light output to be of much
practical use. In the late 1980s, key breakthroughs in GaN epitaxial growth and p-type doping by
Isamu Akasaki and Hiroshi Amano (Nagoya, Japan)[32] ushered in the modern era of GaN-based
optoelectronic devices. Building upon this foundation, in 1993 high brightness blue LEDs were
demonstrated through the work of Shuji Nakamura at Nichia Corporation.[33]

By the late 1990s, blue LEDs had become widely available. They have an active region
consisting of one or more InGaN quantum wells sandwiched between thicker layers of GaN,
called cladding layers. By varying the relative InN-GaN fraction in the InGaN quantum wells,
the light emission can be varied from violet to amber. AlGaN aluminium gallium nitride of
varying AlN fraction can be used to manufacture the cladding and quantum well layers for
ultraviolet LEDs, but these devices have not yet reached the level of efficiency and technological
maturity of the InGaN-GaN blue/green devices. If the active quantum well layers are GaN, as
opposed to alloyed InGaN or AlGaN, the device will emit near-ultraviolet light with wavelengths
around 350±370 nm. Green LEDs manufactured from the InGaN-GaN system are far more
efficient and brighter than green LEDs produced with non-nitride material systems.

With nitrides containing aluminium, most often AlGaN and AlGaInN, even shorter wavelengths
are achievable. Ultraviolet LEDs in a range of wavelengths are becoming available on the
market. Near-UV emitters at wavelengths around 375±395 nm are already cheap and often
encountered, for example, as black light lamp replacements for inspection of anti-counterfeiting
UV watermarks in some documents and paper currencies. Shorter wavelength diodes, while
substantially more expensive, are commercially available for wavelengths down to 247 nm.[34]
As the photosensitivity of microorganisms approximately matches the absorption spectrum of
DNA, with a peak at about 260 nm, UV LEDs emitting at 250±270 nm are to be expected in
prospective disinfection and sterilization devices. Recent research has shown that commercially
available UVA LEDs (365 nm) are already effective disinfection and sterilization devices.[35]

Wavelengths down to 210 nm were obtained in laboratories using aluminium nitride.

 
 

There are two primary ways of producing high intensity white-light using LEDs. One is to use
individual LEDs that emit three primary colors[36] ± red, green, and blue, and then mix all the
colors to produce white light. The other is to use a phosphor material to convert monochromatic
light from a blue or UV LED to broad-spectrum white light, much in the same way a fluorescent
light bulb works.

Due to metamerism, it is possible to have quite different spectra which appear white.
r

  

Combined spectral curves for blue, yellow-green, and high brightness red solid-state semiconductor
LEDs. FWHD spectral bandwidth is approximately 2r 27 nm for all three colors.

White light can be produced by mixing differently colored light, the most common method is to
use red, green and blue (RGB). Hence the method is called multi-colored white LEDs
(sometimes referred to as RGB LEDs). Because its mechanism is involved with sophisticated
electro-optical design to control the blending and diffusion of different colors, this approach has
rarely been used to mass produce white LEDs in the industry. Nevertheless this method is
particularly interesting to many researchers and scientists because of the flexibility of mixing
different colors.[37] In principle, this mechanism also has higher quantum efficiency in producing
white light.

There are several types of multi-colored white LEDs: di-, tri-, and tetrachromatic white LEDs.
Several key factors that play among these different approaches include color stability, color
rendering capability, and luminous efficacy. Often higher efficiency will mean lower color
rendering, presenting a trade off between the luminous efficiency and color rendering. For
example, the dichromatic white LEDs have the best luminous efficacy(120 lm/W), but the lowest
color rendering capability. Conversely, although tetrachromatic white LEDs have excellent color
rendering capability, they often have poor luminous efficiency. Trichromatic white LEDs are in
between, having both good luminous efficacy(>70 lm/W) and fair color rendering capability.

What multi-color LEDs offer is not merely another solution of producing white light, but is a
whole new technique of producing light of different colors. In principle, most perceivable colors
can be produced by mixing different amounts of three primary colors, and this makes it possible
to produce precise dynamic color control as well. As more effort is devoted to investigating this
technique, multi-color LEDs should have profound influence on the fundamental method which
we use to produce and control light color. However, before this type of LED can truly play a role
on the market, several technical problems need to be solved. These certainly include that this
type of LED's emission power decays exponentially with increasing temperature,[38] resulting in
a substantial change in color stability. Such problem is not acceptable for industrial usage.
Therefore, many new package designs aiming to solve this problem have been proposed, and
their results are being

reproduced by researchers and scientists.

r
   
 

Spectrum of a ͞white͟ LED clearly showing blue light which is directly emitted by the GaN-based LED
(peak at about r65 nm) and the more broadband Stokes-shifted light emitted by the Ce3+:YAG phosphor
which emits at roughly 500 700 nm.

This method involves coating an LED of one color (mostly blue LED made of InGaN) with
phosphor of different colors to produce white light, the resultant LEDs are called 


" # =
. A fraction of the blue light undergoes the Stokes shift being transformed
from shorter wavelengths to longer. Depending on the color of the original LED, phosphors of
different colors can be employed. If several phosphor layers of distinct colors are applied, the
emitted spectrum is broadened, effectively increasing the color rendering index (CRI) value of a
given LED.

Phosphor based LEDs have a lower efficiency than normal LEDs due to the heat loss from the
Stokes shift and also other phosphor-related degradation issues. However, the phosphor method
is still the most popular technique for manufacturing high intensity white LEDs. The design and
production of a light source or light fixture using a monochrome emitter with phosphor
conversion is simpler and cheaper than a complex RGB system, and the majority of high
intensity white LEDs presently on the market are manufactured using phosphor light conversion.

The greatest barrier to high efficiency is the seemingly unavoidable Stokes energy loss.
However, much effort is being spent on optimizing these devices to higher light output and
higher operation temperatures. For instance, the efficiency can be increased by adapting better
package design or by using a more suitable type of phosphor. Philips Lumileds' patented
conformal coating process addresses the issue of varying phosphor thickness, giving the white
LEDs a more homogeneous white light. With development ongoing, the efficiency of phosphor
based LEDs is generally increased with every new product announcement.

Technically the phosphor based white LEDs encapsulate InGaN blue LEDs inside of a phosphor
coated epoxy. A common yellow phosphor material is cerium-doped yttrium aluminium garnet
(Ce3+:YAG).

White LEDs can also be made by coating near ultraviolet (NUV) emitting LEDs with a mixture
of high efficiency europium-based red and blue emitting phosphors plus green emitting copper
and aluminium doped zinc sulfide (ZnS:Cu, Al). This is a method analogous to the way
fluorescent lamps work. This method is less efficient than the blue LED with YAG:Ce phosphor,
as the Stokes shift is larger and more energy is therefore converted to heat, but yields light with
better spectral characteristics, which render color better. Due to the higher radiative output of the
ultraviolet LEDs than of the blue ones, both approaches offer comparable brightness. Another
concern is that UV light may leak from a malfunctioning light source and cause harm to human
eyes or skin.

r
    

Another method used to produce experimental white light LEDs used no phosphors at all and
was based on homoepitaxially grown zinc selenide (ZnSe) on a ZnSe substrate which
simultaneously emitted blue light from its active region and yellow light from the substrate.[39]

 $   
$=


Dain article: Organic light-emitting diode

If the emitting layer material of the LED is an organic compound, it is known as an Organic
Light Emitting Diode (OLED). To function as a semiconductor, the organic emitting material
must have conjugated pi bonds. [40] The emitting material can be a small organic molecule in a
crystalline phase, or a polymer. Polymer materials can be flexible; such LEDs are known as
PLEDs or FLEDs.

Compared with regular LEDs, OLEDs are lighter, and polymer LEDs can have the added benefit
of being flexible. Some possible future applications of OLEDs could be:

O? Inexpensive, flexible displays

O? Light sources
O? Wall decorations
O? Luminous cloth

OLEDs have been used to produce visual displays for portable electronic devices such as
cellphones, digital cameras, and MP3 players. Larger displays have been demonstrated,[41] but
their life expectancy is still far too short (<1,000 hours) to be practical[

÷÷].
Today, OLEDs operate at substantially lower efficiency than inorganic (crystalline) LEDs.[42

± 
=
% 

A new technique developed by Michael Bowers, a graduate student at Vanderbilt University in

Nashville, involves coating a blue LED with quantum dots that glow white in response to the
blue light from the LED. This technique produces a warm, yellowish-white light similar to that
produced by incandescent bulbs.[43]

Quantum dots are semiconductor nanocrystals that possess unique optical properties.[44] Their
emission color can be tuned from the visible throughout the infrared spectrum. This allows
quantum dot LEDs to create almost any color on the CIE diagram. This provides more color
options and better color rendering white LEDs. Quantum dot LEDs are available in the same
package types as traditional phosphor based LEDs.

In September 2009 Nanoco Group announced that it has signed a joint development agreement
with a major Japanese electronics company under which it will design and develop quantum dots
for use in light emitting diodes (LEDs) in liquid crystal display (LCD) televisions.[45]

  

LEDs are produced in a variety of shapes and sizes. The 5 mm cylindrical package (red, fifth from the left)
is the most common, estimated at 80% of world production.[u

] The color of the plastic lens is
often the same as the actual color of light emitted, but not always. For instance, purple plastic is often
used for infrared LEDs, and most blue devices have clear housings. There are also LEDs in SDT packages,
such as those found on blinkies and on cell phone keypads (not shown).
The main types of LEDs are miniature, high power devices and custom designs such as
alphanumeric or multi-color.

 &=


Different sized LEDs. 8 mm, 5 mm and 3 mm, with a wooden match-stick for scale.

Dain article: Diniature light-emitting diode

These are mostly single-die LEDs used as indicators, and they come in various-sizes from 2 mm
to 8 mm, through-hole and surface mount packages. They are usually simple in design, not
requiring any separate cooling body.[46] Typical current ratings ranges from around 1 mA to
above 20 mA. The small scale sets a natural upper boundary on power consumption due to heat
caused by the high current density and need for heat sinking.

 ' 
#=


See also: Solid-state lighting and LED lamp

High power LEDs from Philips Lumileds Lighting Company mounted on a 21 mm star shaped base metal
core PCB

High power LEDs (HPLED) can be driven at hundreds of mA to more than an ampere of current,
compared with the tens of mA for other LEDs. They produce several hundred lumens. Since
overheating is destructive, the HPLEDs must be mounted on a heat sink to allow for heat
dissipation. If the heat from a HPLED is not removed, the device will burn out in seconds. A
single HPLED can often replace an incandescent bulb in a flashlight, or be set in an array to form
a powerful LED lamp.

Some well-known HPLED's in this category are the Lumileds Rebel Led, Osram Opto
Semiconductors Golden Dragon and Cree X-lamp. As of September 2009 some HPLEDs
manufactured by () now exceed 105 lm/W [47] (e.g. the XLamp XP-G LED chip emitting
Cool White light) and are being sold in lamps intended to replace incandescent, halogen, and
even fluorescent style lights as LEDs become more cost competitive.

LEDs have been developed by Seoul Semiconductor that can operate on AC power without the
need for a DC converter. For each half cycle part of the LED emits light and part is dark, and this
is reversed during the next half cycle. The efficacy of this type of HPLED is typically 40
lm/W.[48] A large number of LED elements in series may be able to operate directly from line
voltage.

 



O? V  
  are used as attention seeking indicators without requiring external electronics.
Flashing LEDs resemble standard LEDs but they contain an integrated multivibrator circuit inside
which causes the LED to flash with a typical period of one second. In diffused lens LEDs this is
visible as a small black dot. Dost flashing LEDs emit light of a single color, but more
sophisticated devices can flash between multiple colors and even fade through a color sequence
using RGB color mixing.

Old calculator LED display.

O? ð u   are actually two different LEDs in one case. It consists of two dies connected to the
same two leads but in opposite directions. Current flow in one direction produces one color, and
current in the opposite direction produces the other color. Alternating the two colors with
sufficient frequency causes the appearance of a blended third color. For example, a red/green
LED operated in this fashion will color blend to produce a yellow appearance.

O? ! u   are two LEDs in one case, but the two LEDs are connected to separate leads so
that the two LEDs can be controlled independently and lit simultaneously. A three-lead
arrangement is typical with one common lead (anode or cathode).

O? ï ð  contain red, green and blue emitters, generally using a four-wire connection with one
common lead (anode or cathode).

O?

 u  
 are available in seven-segment and starburst format. Seven-segment
displays handle all numbers and a limited set of letters. Starburst displays can display all letters.
Seven-segment LED displays were in widespread use in the 1970s and 1980s, but increasing use
 of liquid crystal displays, with their lower power consumption and greater display flexibility, has
reduced the popularity of numeric and alphanumeric LED displays.

 
 


 c
#


Dain article: LED power sources

The current/voltage characteristics of an LED is similar to other diodes, in that the current is
dependent exponentially on the voltage (see Shockley diode equation). This means that a small
change in voltage can lead to a large change in current. If the maximum voltage rating is
exceeded by a small amount the current rating may be exceeded by a large amount, potentially
damaging or destroying the LED. The typical solution is therefore to use constant current power
supplies, or driving the LED at a voltage much below the maximum rating. Since most
household power sources (batteries, mains) are not constant current sources, most LED fixtures
must include a power converter. However, the I/V curve of nitride-based LEDs is quite steep
above the knee and gives an If of a few mA at a Vf of 3V, making it possible to power a nitride-
based LED from a 3V battery such as a coin cell without the need for a current limiting resistor.

  


Dain article: Electrical polarity of LEDs

As with all diodes, current flows easily from p-type to n-type material.[49] However, no current
flows and no light is produced if a small voltage is applied in the reverse direction. If the reverse
voltage becomes large enough to exceed the breakdown voltage, a large current flows and the
LED may be damaged. If the reverse current is sufficiently limited to avoid damage, the reverse-
conducting LED is a useful noise diode.

  

O?   " LEDs produce more light per watt than incandescent bulbs.[50]
O? 

" LEDs can emit light of an intended color without the use of color filters that traditional
lighting methods require. This is more efficient and can lower initial costs.
O? #" LEDs can be very small (smaller than 2 mm2[51]) and are easily populated onto printed
circuit boards.
O? ÿ$ÿ " LEDs light up very quickly. A typical red indicator LED will achieve full brightness in
microseconds.[52] LEDs used in communications devices can have even faster response times.
O?  
" LEDs are ideal for use in applications that are subject to frequent on-off cycling, unlike
fluorescent lamps that burn out more quickly when cycled frequently, or HID lamps that require
a long time before restarting.
O? °  
" LEDs can very easily be dimmed either by Pulse-width modulation or lowering the
forward current.
 O? 


" In contrast to most light sources, LEDs radiate very little heat in the form of IR that
can cause damage to sensitive objects or fabrics. Wasted energy is dispersed as heat through
the base of the LED.
O? 
% " LEDs mostly fail by dimming over time, rather than the abrupt burn-out of
incandescent bulbs.[53]
O? =  " LEDs can have a relatively long useful life. One report estimates 35,000 to 50,000
hours of useful life, though time to complete failure may be longer.[5r] Fluorescent tubes
typically are rated at about 10,000 to 15,000 hours, depending partly on the conditions of use,
and incandescent light bulbs at 1,000 2,000 hours.
O? 
 " LEDs, being solid state components, are difficult to damage with external
shock, unlike fluorescent and incandescent bulbs which are fragile.
O? V
" The solid package of the LED can be designed to focus its light. Incandescent and
fluorescent sources often require an external reflector to collect light and direct it in a usable
manner.
O? 
&  " LEDs do not contain mercury, unlike fluorescent lamps.

 
 

O? 0
     " LEDs are currently more expensive, price per lumen, on an initial capital cost
basis, than most conventional lighting technologies. The additional expense partially stems from
the relatively low lumen output and the drive circuitry and power supplies needed. However,
when considering the total cost of ownership (including energy and maintenance costs), LEDs far
surpass incandescent or halogen sources and begin to threaten compact fluorescent lamps[u


]
.
O?     " LED performance largely depends on the ambient temperature of
the operating environment. Over-driving the LED in high ambient temperatures may result in
overheating of the LED package, eventually leading to device failure. Adequate heat-sinking is
required to maintain long life. This is especially important when considering automotive,
medical, and military applications where the device must operate over a large range of
temperatures, and is required to have a low failure rate.
O? 

   " LEDs must be supplied with the voltage above the threshold and a current
below the rating. This can involve series resistors or current-regulated power supplies.[55]
O? =
' " Dost cool-white LEDs have spectra that differ significantly from a black body
radiator like the sun or an incandescent light. The spike at r60 nm and dip at 500 nm can cause
the color of objects to be perceived differently under cool-white LED illumination than sunlight
or incandescent sources, due to metamerism,[56] red surfaces being rendered particularly badly
by typical phosphor based cool-white LEDs. However, the color rendering properties of common
fluorescent lamps are often inferior to what is now available in state-of-art white LEDs.
O?


" LEDs do not approximate a ͞point source͟ of light, but rather a lambertian
distribution. So LEDs are difficult to use in applications requiring a spherical light field. LEDs are
not capable of providing divergence below a few degrees. This is contrasted with lasers, which
can produce beams with divergences of 0.2 degrees or less.[57]
O? ð0# " There is increasing concern that blue LEDs and cool-white LEDs are now capable of
exceeding safe limits of the so-called blue-light hazard as defined in eye safety specifications
such as ANSI/IESNA RP-27.1-05: Recommended Practice for Photobiological Safety for Lamp and
Lamp Systems.[58][59]
O? ð

" Because cool-white LEDs (i.e., LEDs with high color temperature) emit much
more blue light than conventional outdoor light sources such as high-pressure sodium lamps,
 the strong wavelength dependence of Rayleigh scattering means that cool-white LEDs can cause
more light pollution than other light sources. It is therefore very important that cool-white LEDs
are fully shielded when used outdoors. Compared to low-pressure sodium lamps, which emit at
589.3 nm, the r60 nm emission spike of cool-white and blue LEDs is scattered about 2.7 times
more by the Earth's atmosphere. Cool-white LEDs should not be used for outdoor lighting near
astronomical observatories.




A large LED display behind a disc jockey.

LED destination displays on buses, one with a colored route number.

LED digital display that can display r digits along with points.
Traffic light using LED

Western Australia Police car using LED

Dropped ceiling with LED lamps

LED daytime running lights of Audi Ar

Illustration of the cost of using a single Incandescent, CFL, LED (at current market price) and an LED (at
estimated price within a couple years) each year over the span of a decade.

LED panel light source used in an experiment on plant growth. The findings of such experiments may be
used to grow food in space on long duration missions.

The many application of LEDs are very diverse but fall into three major categories: Visual signal
application where the light goes more or less directly from the LED to the human eye, to convey
a message or meaning. Illumination where LED light is reflected from object to give visual
response of these objects. Finally LEDs are also used to generate light for measuring and
interacting with processes that do not involve the human visual system.[60]

r

 
  

The low energy consumption, low maintenance and small size of modern LEDs has led to
applications as status indicators and displays on a variety of equipment and installations. Large
area LED displays are used as stadium displays and as dynamic decorative displays. Thin,
lightweight message displays are used at airports and railway stations, and as destination displays
for trains, buses, trams, and ferries.

The single color light is well suited for traffic lights and signals, exit signs, emergency vehicle
lighting, ships' lanterns and LED-based Christmas lights. Red or yellow LEDs are used in
indicator and alphanumeric displays in environments where night vision must be retained:
aircraft cockpits, submarine and ship bridges, astronomy observatories, and in the field, e.g.
night time animal watching and military field use.

Because of their long life and fast switching times, LEDs have been used for automotive high-
mounted brake lights and truck and bus brake lights and turn signals for some time, but many
vehicles now use LEDs for their rear light clusters. The use of LEDs also has styling advantages
because LEDs are capable of forming much thinner lights than incandescent lamps with
parabolic reflectors. The significant improvement in the time taken to light up (perhaps 0.5s
faster than an incandescent bulb) improves safety by giving drivers more time to react. It has
been reported that at normal highway speeds this equals one car length increased reaction time
for the car behind. White LED headlamps are beginning to make an appearance.

Due to the relative cheapness of low output LEDs they are also used in many temporary
applications such as glowsticks and throwies and Lumalive, a photonic textile, artist have also
used LEDs for LED art.

Weather/all-hazards radio receivers with Specific Area Message Encoding (SAME) have three
LEDs: red for warnings, orange for watches, and yellow for advisories & statements whenever
issued.

r
 

With the development of high efficiency and high power LEDs it has become possible to
incorporate LEDs in lighting and illumination. Replacement light bulbs have been made as well
as dedicated fixtures and LED lamps. LEDs are used as street lights and in other architectural
lighting where color changing is used. The mechanical robustness and long lifetime is used in
automotive lighting on cars, motorcycles and on bicycle lights.

LEDs have been used for lighting of streets and of parking garages. In 2007, the Italian village
Torraca was the first place to convert its entire illumination system to LEDs.[61]

LEDs are also suitable for backlighting for LCD televisions and lightweight laptop displays and
light source for DLP projectors (See LED TV). RGB LEDs increase the color gamut by as much
as 45%. Screens for TV and computer displays can be made increasingly thin using LEDs for
backlighting.[62]

The lack of IR/heat radiation makes LEDs ideal for stage lights using banks of RGB LEDs that
can easily change color and decrease heating from traditional stage lighting, as well as medical
lighting where IR-radiation can be harmful.
Since LEDs are small, durable and require little power they are used in hand held devices such as
flashlights. LED strobe lights or camera flashes operate at a safe, low voltage, as opposed to the
250+ volts commonly found in xenon flashlamp-based lighting. This is particularly applicable to
cameras on mobile phones, where space is at a premium and bulky voltage-increasing circuitry is
undesirable. LEDs are used for infrared illumination in night vision applications including
security cameras. A ring of LEDs around a video camera, aimed forward into a retroreflective
background, allows chroma keying in video productions.

LEDs are used for decorative lighting as well. Uses include but are not limited to indoor/outdoor
decor, limousines, cargo trailers, conversion vans, cruise ships, RVs, boats, automobiles, and
utility trucks. Decorative LED lighting can also come in the form of lighted company signage
and step and aisle lighting in theaters and auditoriums.

r
 

Light can be used to transmit broadband data, which is already implemented in IrDA standards
using infrared LEDs. Because LEDs can cycle on and off millions of times per second, they can,
in effect, become wireless routers for data transport.[63] Lasers can also be modulated in this
manner.

r
   

Efficient lighting is needed for sustainable architecture. A 13 watt LED lamp produces 450 to
650 lumens [64]. which is equivalent to a standard 40 watt incandescent bulb [65]. A standard 40 W
incandescent bulb has an expected lifespan of 1,000 hours while an LED can continue to operate
with reduced efficiency for more than 50,000 hours, 50 times longer than the incandescent bulb.

r
 
  
 


A single kilowatt-hour of electricity will generate 1.34 pounds (610 g) of CO2 emissions.[66]
Assuming the average light bulb is on for 10 hours a day, a single 40-watt incandescent bulb will
generate 196 pounds (89 kg) of CO2 every year. The 13-watt LED equivalent will only be
responsible for 63 pounds (29 kg) of CO2 over the same time span. A building¶s carbon footprint
from lighting can be reduced by 68% by exchanging all incandescent bulbs for new LEDs.

LEDs are also non-toxic unlike the more popular energy efficient bulb option: the compact
florescent a.k.a. CFL which contains traces of harmful mercury. While the amount of mercury in
a CFL is small, introducing less into the environment is preferable.

r
    

LED light bulbs could be a cost effective option for lighting a home or office space because of
their very long lifetimes, even though they have a much higher purchase price. The high initial
cost of the commercial LED bulb is due to the expensive sapphire substrate which is key to the
production process. The sapphire apparatus must be coupled with a mirror-like collector to
reflect light that would otherwise be wasted.
During this transition period, it is a challenge to ensure that this technology is used where it is
most appropriate and effective, and to avoid poor-quality products damaging the reputation. 2009
DOE testing results showed an average efficacy of 35 lm/W, below that of typical CFLs, and as
low as 9 lm/W, worse than standard incandescents [64]. It is a challenge to get buyers and users to
be conscious of and make decisions based on life-cycle costs instead of the more obvious initial
purchase price, and to avoid having low-efficiency products ride on the coattails of hype
generated by lab test results.

In 2008, a materials science research team at Purdue University succeeded in producing LED
bulbs with a substitute for the sapphire components.[67]. The team used metal-coated silicon
wafers with a built-in reflective layer of zirconium nitride to lessen the overall production cost of
the LED. They predict that within a few years, LEDs produced with their revolutionary, new
technique will be competitively priced with CFLs. The less expensive LED would not only be
the best energy saver, but also a very economical bulb.

r
 !  

Light has many other uses besides for seeing. LEDs are used for some of these applications. The
uses fall in three groups: Communication, sensors and light matter interaction.

The light from LEDs can be modulated very fast so they are extensively used in optical fiber and
Free Space Optics communications. This include remote controls, such as for TVs and VCRs,
where infrared LEDs are often used. Opto-isolators use an LED combined with a photodiode or
phototransistor to provide a signal path with electrical isolation between two circuits. This is
especially useful in medical equipment where the signals from a low voltage sensor circuit
(usually battery powered) in contact with a living organism must be electrically isolated from
any possible electrical failure in a recording or monitoring device operating at potentially
dangerous voltages. An optoisolator also allows information to be transferred between circuits
not sharing a common ground potential.

Many sensor systems rely on light as the main medium. LEDs are often ideal as a light source
due to the requirements of the sensors. LEDs are used as movement sensors, for example in
optical computer mice. The Nintendo Wii's sensor bar uses infrared LEDs. In pulse oximeters for
measuring oxygen saturation. Some flatbed scanners use arrays of RGB LEDs rather than the
typical cold-cathode fluorescent lamp as the light source. Having independent control of three
illuminated colors allows the scanner to calibrate itself for more accurate color balance, and there
is no need for warm-up. Furthermore, its sensors only need be monochromatic, since at any one
point in time the page being scanned is only lit by a single color of light. Touch sensing: Since
LEDs can also be used as photodiodes, they can be used for both photo emission and detection.
This could be used in for example a touch-sensing screen that register reflected light from a
finger or stylus.[68]

Many materials and biological systems are sensitive to, or dependent on light. Grow lights use
LEDs to increase photosynthesis in plants[69] and bacteria and vira can be removed from water
and other substances using UV LEDs for sterilization[35]. Other uses are as UV curing devices for
some ink and coating applications as well as LED printers.
The use of LEDs is particularly interesting to plant cultivators, mainly because it is more energy
efficient, less heat is produced (can damage plants close to hot lamps) and can provide the
optimum light frequency for plant growth and bloom periods compared to currently used grow
lights: HPS (High Pressure Sodium), MH (Metal Halide) or CFL/Low-energy. It has however
not replaced these grow lights due to it having a higher retail price, as mass production and LED
kits develop the product will become cheaper.

LEDs have also been used as a medium quality voltage reference in electronic circuits. The
forward voltage drop (e.g., about 1.7 V for a normal red LED) can be used instead of a Zener
diode in low-voltage regulators. Red LEDs have the flattest I/V curve above the knee; nitride-
based LEDs have a fairly steep I/V curve and are not useful in this application. Although LED
forward voltage is much more current-dependent than a good Zener, Zener diodes are not widely
available below voltages of about 3 V.

= 

  
 

Machine vision systems often require bright and homogeneous illumination, so features of
interest are easier to process. LEDs are often used to this purpose, and this field of application is
likely to remain one of the major application areas until price drops low enough to make
signaling and illumination applications more widespread. Barcode scanners are the most
common example of machine vision, and many inexpensive ones used red LEDs instead of
lasers. LEDs constitute a nearly ideal light source for machine vision systems for several
reasons:

The size of the illuminated field is usually comparatively small and machine vision systems are
often quite expensive, so the cost of the light source is usually a minor concern. However, it
might not be easy to replace a broken light source placed within complex machinery, and here
the long service life of LEDs is a benefit.

LED elements tend to be small and can be placed with high density over flat or even shaped
substrates (PCBs etc) so that bright and homogeneous sources can be designed which direct light
from tightly controlled directions on inspected parts. This can often be obtained with small,
inexpensive lenses and diffusers, helping to achieve high light densities with control over
lighting levels and homogeneity. LED sources can be shaped in several configurations (spot
lights for reflective illumination; ring lights for coaxial illumination; back lights for contour
illumination; linear assemblies; flat, large format panels; dome sources for diffused,
omnidirectional illumination).

LEDs can be easily strobed (in the microsecond range and below) and synchronized with
imaging. High power LEDs are available allowing well lit images even with very short light
pulses. This is often used in order to obtain crisp and sharp ³still´ images of quickly-moving
parts.

LEDs come in several different colors and wavelengths, easily allowing to use the best color for
each application, where different color may provide better visibility of features of interest.
Having a precisely known spectrum allows tightly matched filters to be used to separate
informative bandwidth or to reduce disturbing effect of ambient light. LEDs usually operate at
comparatively low working temperatures, simplifying heat management and dissipation,
therefore allowing plastic lenses, filters and diffusers to be used. Waterproof units can also easily
be designed, allowing for use in harsh or wet environments (food, beverage, oil industries).





  
 

Jump to: navigation, search

For other uses, see Dynamo (disambiguation).

A 
, originally another name for an electrical generator, now means a generator that
produces direct current with the use of a commutator. Dynamos were the first electrical
generators capable of delivering power for industry, and the foundation upon which many other
later electric-power conversion devices were based, including the electric motor, the alternating-
current alternator, and the rotary converter. They are rarely used for power generation now
because of the dominance of alternating current, the disadvantages of the commutator, and the
ease of converting alternating to direct current using solid state methods.

The word still has some regional usage as a replacement for the word  . A small
electrical generator built into the hub of a bicycle wheel to power lights is called a Hub dynamo.

Dynamo Electric Dachine [End View, Partly Section] (U.S. Patent 28r,110)

The dynamo uses rotating coils of wire and magnetic fields to convert mechanical rotation into a
pulsing direct electric current through Faraday's law. A dynamo machine consists of a stationary
structure, called the stator, which provides a constant magnetic field, and a set of rotating
windings called the armature which turn within that field. On small machines the constant
magnetic field may be provided by one or more permanent magnets; larger machines have the
constant magnetic field provided by one or more electromagnets, which are usually called Ô
÷

.
The commutator was needed to produce direct current. When a loop of wire rotates in a magnetic
field, the potential induced in it reverses with each half turn, generating an alternating current.
However, in the early days of electric experimentation, alternating current generally had no
known use. The few uses for electricity, such as electroplating, used direct current provided by
messy liquid batteries. Dynamos were invented as a replacement for batteries. The commutator is
a set of contacts mounted on the machine's shaft, which reverses the connection of the windings
to the external circuit when the potential reverses, so instead of alternating current, a pulsing
direct current is produced.

 '
 

The first electric generator was invented by Michael Faraday in 1831, a copper disk that rotated
between the poles of a magnet. This was not a dynamo because it did not use a commutator.
However, Faraday's disk generated very low voltage because of its single current path through
the magnetic field. Faraday and others found that higher, more useful voltages could be produced
by winding multiple turns of wire into a coil. Wire windings can conveniently produce any
voltage desired by changing the number of turns, so they have been a feature of all subsequent
generator designs, requiring the invention of the commutator to produce direct current.

 * + 


Dain article: Jedlik's dynamo

Pixii's dynamo. The commutator is located on the shaft below the spinning magnet.

In 1827, Hungarian Anyos Jedlik started experimenting with electromagnetic rotating devices
which he called electromagnetic self-rotors. In the prototype of the single-pole electric starter,
both the stationary and the revolving parts were electromagnetic. He formulated the concept of
the dynamo about six years before Siemens and Wheatstone but did not patent it as he thought he
was not the first to realize this. His dynamo used, instead of permanent magnets, two
electromagnets opposite to each other to induce the magnetic field around the rotor.[1][2]

 c%+ 


The first dynamo based on Faraday's principles was built in 1832 by Hippolyte Pixii, a French
instrument maker. It used a permanent magnet which was rotated by a crank. The spinning
magnet was positioned so that its north and south poles passed by a piece of iron wrapped with
wire. Pixii found that the spinning magnet produced a pulse of current in the wire each time a
pole passed the coil. However, the north and south poles of the magnet induced currents in
opposite directions. To convert the alternating current to DC, Pixii invented a commutator, a split
metal cylinder on the shaft, with two springy metal contacts that pressed against it.

 c
 


Pacinotti dynamo, 1860

These early designs had a problem: the electric current they produced consisted of a series of
"spikes" or pulses of current separated by none at all, resulting in a low average power output.
Antonio Pacinotti, an Italian physics professor, solved this problem around 1860 by replacing the
spinning two-pole axial coil with a multi-pole toroidal one, which he created by wrapping an iron
ring with a continuous winding, connected to the commutator at many equally spaced points
around the ring; the commutator being divided into many segments. This meant that some part of
the coil was continually passing by the magnets, smoothing out the current.

   

 
,-./

The first practical designs for a dynamo were announced independently and simultaneously by
Dr. Werner Siemens and Charles Wheatstone. On January 17, 1867, Siemens announced to the
Berlin academy a "dynamo-electric machine" (first use of the term) which employed a self-
powering electromagnetic armature.[3] On the same day that this invention was announced to the
Royal Society Charles Wheatstone read a paper describing a similar design with the difference
that in the Siemens design the armature was in series with the rotor, but in Wheatstone's design it
was in parallel.[4] The use of electromagnets rather than permanent magnets greatly increases the
power output of a dynamo and enabled high power generation for the first time. This invention
led directly to the first major industrial uses of electricity. For example, in the 1870s Siemens
used electromagnetic dynamos to power electric arc furnaces for the production of metals and
other materials.

 0  


Small Gramme dynamo, around 1878

How Gramme dynamo works to produce a smooth output waveform.

Dain article: Gramme dynamo

Zénobe Gramme reinvented Pacinotti's design in 1871 when designing the first commercial
power plants, which operated in Paris in the 1870s. Another advantage of Gramme's design was
a better path for the magnetic flux, by filling the space occupied by the magnetic field with heavy
iron cores and minimizing the air gaps between the stationary and rotating parts. The 
÷ was the first machine to generate commercial quantities of power for industry. Further
improvements were made on the Gramme ring, but the basic concept of a spinning endless loop
of wire remains at the heart of all modern dynamos.







While not originally designed for the purpose, it was discovered that a dynamo can act as an
electric motor when supplied with direct current from a battery or another dynamo. At an
industrial exhibition in Vienna in 1873, Gramme noticed that the shaft of his dynamo began to
spin when its terminals were accidentally connected to another dynamo producing electricity.
Although this wasn't the first demonstration of an electric motor, it was the first practical one. It
was found that the same design features which make a dynamo efficient also make a motor
efficient. The efficient Gramme design, with small magnetic air gaps and many coils of wire
attached to a many-segmented commutator, also became the basis for the design of all practical
DC motors.

Large dynamos producing direct current were problematic in situations where two or more
dynamos are working together and one has an engine running at a lower power than the other.
The dynamo with the stronger engine will tend to drive the weaker as if it were a motor, against
the rotation of the weaker engine. Such reverse-driving could feed back into the driving engine
of a dynamo and cause a dangerous out of control reverse-spinning condition in the lower-power
dynamo. It was eventually determined that when several dynamos all feed the same power
source all the dynamos must be locked into synchrony using a jackshaft interconnecting all
engines and rotors to counter these imbalances.

 


 
0


After the discovery of the AC Generator and that alternating current can in fact be useful for
something, the word ÷ became associated exclusively with the    ÷ 

 , while an AC electrical generator using either slip rings or rotor magnets would
become known as an alternator.

An AC electric motor using either slip rings or rotor magnets was referred to as a synchronous
motor, and a commutated DC electric motor could be called either an  
  though with
the understanding that it could in principle operate as a generator.

 1



 

After dynamos were found to allow easy conversion back and forth between mechanical or
electrical power, the new discovery was used to develop complex multi-field single-rotor devices
with two or more commutators. These were known as a rotary converters. These devices were
usually not burdened by mechanical loads, but watched just spinning on their own.

The rotary converter can directly convert, internally, any power source into any other. This
includes direct current (DC) into alternating current (AC), 25 cycle AC into 60 cycle AC, or
many different output currents at the same time. The size and mass of these was very large so
that the rotor would act as a flywheel to help smooth out any sudden surges or dropouts.

The technology of rotary converters ruled until the development of vacuum tubes allowed for
electronic oscillators. This eliminated the need for physically spinning rotors and commutators.

 &

Dynamos still have some uses in low power applications, particularly where low voltage DC is
required, since an alternator with a semiconductor rectifier can be inefficient in these
applications. Hand cranked dynamos are used in clockwork radios, lamps (LEDs), mobile
phones (i.e. using USB port) and other human powered equipment to recharge batteries.