Commands list for RNC upgrade HC

============================================================================================
3Health Check Before Upgrade
============================================================================================

3.4.1Check Cell/Link/Device status

< Read MO's ><1>
1.lt ^utrancell|^pch|rach|fach|hsdsch|eul|iublink|nbap|nodesync
2.lt mtp3b|sccp|m3ua|sctp|ranap|rnsap|gigabit|ipacc|ipinter|ipeth|ether|vcltp
3.lt ccdev|dcdev|pdr|packetd|spm|plugin|spdev|rncfeature|stp|aal|upgradepa

< Alarm ><2>

1.alt

< Link status ><3>

1.st sccp|mtp3b|m3ua|sctp|ranap|rnsap
2.st sccp|mtp3b|m3ua|sctp|ranap|rnsap dis

3.st iublink
4.st iublink dis
5.lst iublink dis

6.lst vcltp dis

7.pget m3ua|sctp

8.st gigabit|ipaccesshost

9.sget GigaBitEthernet link.state|activelink

10. sget ipint.* (0|1)state

11. st IpEthPacketDataRouter

12. pmx IpEthPacketDataRouter

< Traffic status ><4>

1.lh ranapmp ueregprint sum
2.lh ranapmp ranap status
3.lh ranapmp ranap conn
4.lh ranapmp rnsap status
5.lh ranapmp rnsap dumpRoTable
< Cell status ><5>
1.st utrancell
2.st utrancell dis
3.lst utrancell
4.lst utrancell dis
5.str

< Device status ><6>

1.st ccdev|dcdev|pdr|packetd|spm|plugin
2.st ccdev|dcdev|pdr|packetd|spm|plugin dis
3.std
4.lh mod drh_dcrh_topdata
5.sget spdevicepool
6.lh mod drh_ccrh_topdata
7.cedr
8.lh mod drh_trbr_data iphost

< Other status ><7>

1.cabx
2.lgaevsmor 5h
3.lgusrm 5h
4.lh all llog -l
5.cabr
6.dump list -a
7.all err
8.hget rncfeature state
9.readclock

10. lst EthernetSwitchPort

11. sget switchportstp stprole
12. each capi check
lh ranapmp capi tot
lh ranapmp capi tot
lh ranapmp capi prio--> select high load pri -> x
lh ranapmp capi type pri <x>
lh ranapmp capi tot
lh ranapmp capi tot
lh ranapmp capi prio--> select high load pri -> y
lh ranapmp capi type pri <y>
13. invr
14. sget switchportstp manualpathcost
15. sget RabHandling=1 maxAllowedGbrUlPsSpeech
< Disk capacity ><8>
1.cabd
2.lh coremp vols /c
3.lh coremp vols /d
4.lh coremp ls /c/loadmodules |awk '{print $1}' |uniq -c
5.lh coremp ls /d/loadmodules |awk '{print $1}' |uniq -c

< Initializing trace ><9> only nighttime preHC

1.lh mod te default -restart
2.lh mod te default *

< Check trace status ><10>

1.lh mp te s -restart
2.cabe (if using latest moshell, lh mp fte s.

< DB check ><11> only daytime

1.ftget /d/configuration/cv/<latest CV name>
2.nowshell -d db.dat (from cv folder on tp server.
3.dbc db.dat (on offline mode.

3.4.2Check the status of Reliable Programs

1.lh mp sma -all

3.4.3Check the FTC state in Main MP

1.lh coremp mirror s
2.getAttrObj me

FTC switch
<<< RNC3810 >>>
1)bl 001100
2)acc 001100 manualrestart
3)getAttrObj me
4)deb 001100
5)lh coremp mirror s
6)getAttrObj me
<<< RNC3820 >>>
1)bl 002400
2)acc 002400 manualrestart
3)getAttrObj me
4)deb 002400
5)lh coremp mirror s
6)getAttrObj me

3.4.4Check Traffic availability (Night)

1.lh ranapmp ueregprint sum
2.pmrup -m 1

3.4.5Check the Flash disk failure in all MPs (Day)

1.lh mp ls /d |grep -i not
2.lh mp ls /c |grep -i not

3.5.1Check the number of CVs (Day)

1.cvls
2.cvls

3.5.2Set the latest CV in Rollback list and check the rollback list (Night)
1.cvls
2.cv rbset < Latest CV >
3.cvls
4.lh coremp cat /d/rollback.lst

3.5.3Backup the cv.ptr (Night)

1.cvcu
2.cat /d/cv.ptr
3.cp /d/cv.ptr /d/cv.ptr.org
4.cat /d/cv.ptr.org
5.cat /d/cv.ptr

=For emergency Recovery=

> reload --(minus minus)
> cp cv.ptr.org cv.ptr
> reload
========================

3.6Make a connection to Serial Console Server (Day, Night)

1.tp machine> telnet -e "^A" <ip address of gateway server>
User/Pass: support/support123

2.serial server>telnet -e "^A" <host name> <port no>

User/Pass: support/support123

3.7Install the License Key File (Day)

1.license server
2.license key
3.license lkf

3.8 Deletion of Aal0TpVccTp

1.alt
2.lst aal0TpVccTp
3.trun <MO script for RNC>
4.alt
5.lt aal0TpVccTp
6.lst aal0TpVccTp
7.mobatch <MOS script for RBS>
(e.g.)mobatch -p 1 TRNC70_AAL0_cleanup_RBSlist.txt RBS_TRNC70_AAL0_cleanup.mos
8.alt

3.9.1Check Upgrade Controll file (Day/Night)

cksum CXP9014711%4_R2EA.xml
cat CXP9014711%4_R2EA.xml | egrep "confirm|WaitForConfirm_BeforeRestart"

3.9.2Get MO dump
<<< RNC3810 >>>
Terminal 1
1.l+m [Node]_dump_[SWname]_beforeUp.log
2.lhsh 001200 capi prio
3.lt all
4.lhsh 001200 capi prio
5.kget
6.lhsh 001200 capi prio
7.l-

Terminal 2
1.l+ [Node]_dump_[SWname]_beforeUp_ldmon.log
2.for 2000
3.lhsh 001200 capi prio
4.done

<<< RNC3820 >>>

Terminal 1
1.l+m [Node]_dump_[SWname]_beforeUp.log
2.lhsh 000500 capi prio
3.lt all
4.lhsh 000500 capi prio
5.kget
6.lhsh 000500 capi prio
7.l-

Terminal 2
1.l+ [Node]_dump_[SWname]_beforeUp_ldmon.log
2.for 2000
3.lhsh 000500 capi prio
4.done

============================================================================================
4RNC Software Install
============================================================================================
4.4Check and Store the Si CV for recovery GPB (Night)
1.lh coremp cv csum <Si_xxxx>
2.ftget /d/configuration/cv/Si_xxxx
4.5Put prepared CV to increase heap size for prevention of cyclic restarts after rollback

ftput xRNCxx_prepared_CV_for_Rollback /d/configuration/cv/

ls /d/configuration/cv/

============================================================================================
5RNC Software Upgrade
============================================================================================

5.1Remove the PM scanners for user-defined

1.pst
2.pst

5.3 Switch Targetmonitor to Active coreMP

1.lt ReliableProgramUniter
2.pr ReliableProgramUniter
3.lh coremp sma -all(Find the targetmonitor RPU)
4.lsget ReliableProgramUniter userLabel target
5.sget ReliableProgramUniter=xxxxxxxx
(xxxx = ReliableProgramUniterId)

6.acl ReliableProgramUniter=xxxxxxxxxxx
(xxxx = ReliableProgramUniterId)
7.acc ReliableProgramUniter=xxxxxxxxxxx switch
(xxxx = ReliableProgramUniterId)
8.sget ReliableProgramUniter=xxxxxxxx
9.lsget ReliableProgramUniter userLabel target
10. lh coremp sma -all(Find the targetmonitor RPU)

<<< RNC3810 >>>

11. sgetReliableProgramUniter=xxxxxx
12. set ReliableProgramUniter=xxxxxxx admActiveSlot Subrack=MS,Slot=10
13. set ReliableProgramUniter=xxxxxxx admPassiveSlot Subrack=MS,Slot=11
14. sgetReliableProgramUniter=xxxxxx
(confirm right configuration)
<<< RNC3820 >>>
11. sgetReliableProgramUniter=xxxxxx
12. set ReliableProgramUniter=xxxxxxx admActiveSlot Subrack=MS,Slot=5
13. set ReliableProgramUniter=xxxxxxx admPassiveSlot Subrack=MS,Slot=24
14. sgetReliableProgramUniter=xxxxxx
(confirm right configuration)

15. lh coremp sma -all

(Find the targetmonitor RPU)

(Extra info)
<<< RNC3810 >>>
1.lhsh 001000 sma -all
2.sget ReliableProgramUniter rpuid <RPU id>
3.sget ReliableProgramUniter=<MO identity>
<<< RNC3820 >>>
1.lhsh 000500 sma -all
2.sget ReliableProgramUniter rpuid <RPU id>
3.sget ReliableProgramUniter=<MO identity>

5.4Perform Software upgrade

1.
lt upgradepackage
2.
pr upgradepackage
sget UpgradePackage=CXP9014711/4_R2EA prog|stat
3.
actl UpgradePackage=CXP9014711/4_R2EA
acc UpgradePackage=CXP9014711/4_R2EA rebootNodeUpgrade

5.5Upgrade Status and KPI Monitoring

1.sget [UpgradePackage] state|prog
2.pmrup -m 1

5.6Upgrade restart execution

sget UpgradePackage=CXP9014711/4_R2EA state|prog

actl UpgradePackage=CXP9014711/4_R2EA
acc UpgradePackage=CXP9014711/4_R2EA confirmUpgrade
5.7.1Check the UE connectivity to the Core network
<<< RNC3810 >>>
1.l+ xrncxx_PostQHC.log
2.lhsh 001700 ueregprint sum
3.lhsh 001700 ranap status
4.lhsh 001700 ranap conn
5.lhsh 001800 rnsap status
6.lhsh 001800 rnsap conn
7.lgevsmur 30m

<<< RNC3820 >>>

1.l+ xrncxx_PostQHC.log
2.lhsh 002200 ueregprint sum
3.lhsh 000700 ranap status
4.lhsh 000700 ranap conn
5.lhsh 002200 rnsap status
6.lhsh 002200 rnsap conn
7.lgevsmur 30m

5.7.2Check ET-M4 Overload

1.lgsemr 10m
2.lhsh xxxxxx(target ETB) capi tot

5.7.3Check program crashes after Upgrade (CSR1783379)

1.lgsemr 10m

================================
a)Terminal 1 (logfile1) repeatably collect:
for ever
;lhsh 000700 rof_info_esig lap;lhsh 000700 poolinfo -l
wait 1
done

b)Terminal 2, (logfile2) repeatably collect:

for ever

;sctphost_stat -assoc -all;lhsh 000700 rof_link_counters

wait 1
done

c)Terminal 3, (logfile3) repeatably collect:

for ever
;lhsh 000700 poolinfo -l CXC1720925_R74G39
wait 1
done

d)Terminal 4, (logfile4) collect:

with telnet
>lhsh 000700 ps|grep RnhLmRanapCPT--- check pid
>lhsh 000700 ps|grep Scc_server_proc--- check pid
e.g.)
SQRNC12> lhsh 000700 ps|grep RnhLmRanapCPT
00010320 RnhLmRanapCPTp23 CXC1727616%4_R1JA04161 rcv(RncLmRanap)
SQRNC12> lhsh 000700 ps|grep Scc_server_proc
000101d5 Scc_server_proc p19 CXC1720925_R74G3950 rcv(SccServer)

>lhsh 000700 sigs 000101d5

>lhsh 000700 sigs 00010320

then moshell
for ever
;lhsh 000700 sigs 000101d5;lhsh 000700 sigs 00010320
wait 1
done

================================

2.lgsemr 10m
3.cv cu

(RNC3810)
4.lhsh 001000 sma -all
lhsh 001100 sma -all
5.cv cu
6.lgsemr 10m
7.lhsh 001000 sma -all
lhsh 001100 sma -all
alt
8.lst 001000
9.bl 001000
10. lst 001000
11. lhsh 001000 sma -all
lhsh 001100 sma -all
12. alt
13. lst 001000
14. deb 001000
15. lst 001000
16. lgsemr 10m
17. lhsh 001000 sma -all
lhsh 001100 sma -all

(RNC3820)
4.lhsh 000500 sma -all
lhsh 002400 sma -all
5.cv cu
6.lgsemr 10m
7.lhsh 000500 sma -all
lhsh 002400 sma -all
alt
8.lst 000500
9.bl 000500
10. lst 000500
11. lhsh 000500 sma -all
lhsh 002400 sma -all
12. alt
13. lst 000500
14. deb 000500
15. lst 000500
16. lgsemr 10m
17. lhsh 000500 sma -all
lhsh 002400 sma -all

5.7.4Confirm Mirroring to be finished

1.lh coremp mirror s
2.getAttrObj me

5.7.5Normality check
< Read MO's ><1>
1.lt ^utrancell|^pch|rach|fach|hsdsch|eul|iublink|nbap|nodesync
2.lt mtp3b|sccp|m3ua|sctp|ranap|rnsap|gigabit|ipacc|ipinter|ipeth|ether|vcltp
3.lt ccdev|dcdev|pdr|packetd|spm|plugin|spdev|rncfeature

< Alarm ><2>

1.alt

< Link status ><3>

1.st sccp|mtp3b|m3ua|sctp|ranap|rnsap dis
2.st gigabit|ipaccesshost
3.sget GigaBitEthernet link.state|activelink
4.sget ipint.* (0|1).state
5.st IpEthPacketDataRouter
6.lpget m3ua pmnoofdatamsg
(Check the counter values increases gradually)

< Cell status ><4>

1.st utrancell dis
2.lst utrancell|pch|rach|fach|hsdsch|eul dis
3.str

< Device status ><5>

1.st ccdev|dcdev|pdr|packetd|spm|plugin dis
2.std

< Other status ><6>

1.lgaevsmour 1h

<RNC3810>
2. each capi check
lh ranapmp capi tot
lh ranapmp capi tot
lh ranapmp capi prio--> select high load pri -> x
lh ranapmp capi type pri <x>
lh ranapmp capi tot
lh ranapmp capi tot
lh ranapmp capi prio--> select high load pri -> y
lh ranapmp capi type pri <y>
<RNC3820>
2. each capi check (Repeat the following for 3 times)
lh sccpmp capi tot
lh sccpmp capi tot
lh sccpmp capi prio--> select high load pri -> x
lh sccpmp capi type pri <x>
lh sccpmp capi tot
lh sccpmp capi tot
lh sccpmp capi prio--> select high load pri -> y
lh sccpmp capi type pri <y>

5.8Take the node trace logs

1.vii
2.run dcg_datacollection_8.0r_modified_110608.mos <A> <B> e
<A> Path of the log output.
<B> Node name. (used for log file naming)
3.(only 3810)
run dcg_script_noOMS_version_090813_ES3_4_ver6.mos
run dcg_script_noOMS_version_090813_ES11_12_ver6.mos

5.9 Switch Targetmonitor to Standby coreMP

1.lt ReliableProgramUniter
2.pr ReliableProgramUniter
3.lh coremp sma -all(Find the targetmonitor RPU)
4.lsget ReliableProgramUniter userLabel target
5.sget ReliableProgramUniter=xxxxxxxx
(xxxx = ReliableProgramUniterId)

6.acl ReliableProgramUniter=xxxxxxxxxxx
(xxxx = ReliableProgramUniterId)
7.acc ReliableProgramUniter=xxxxxxxxxxx switch
(xxxx = ReliableProgramUniterId)
8.sget ReliableProgramUniter=xxxxxxxx
9.lsget ReliableProgramUniter userLabel target
10. lh coremp sma -all(Find the targetmonitor RPU)

<<< RNC3810 >>>

11. sgetReliableProgramUniter=xxxxxx
12. set ReliableProgramUniter=xxxxxxx admActiveSlot Subrack=MS,Slot=11
13. set ReliableProgramUniter=xxxxxxx admPassiveSlot Subrack=MS,Slot=10
14. sgetReliableProgramUniter=xxxxxx
(confirm right configuration)
<<< RNC3820 >>>
11. sgetReliableProgramUniter=xxxxxx
12. set ReliableProgramUniter=xxxxxxx admActiveSlot Subrack=MS,Slot=24
13. set ReliableProgramUniter=xxxxxxx admPassiveSlot Subrack=MS,Slot=5
14. sgetReliableProgramUniter=xxxxxx
(confirm right configuration)

15. lh coremp sma -all

(Find the targetmonitor RPU)

(Extra info)
<<< RNC3810 >>>
1.lhsh 001000 sma -all
2.sget ReliableProgramUniter rpuid <RPU id>
3.sget ReliableProgramUniter=<MO identity>
<<< RNC3820 >>>
1.lhsh 000500 sma -all
2.sget ReliableProgramUniter rpuid <RPU id>
3.sget ReliableProgramUniter=<MO identity>

5.10Activate the DailyTrace

1.lh all te alt status |egrep overload
2.(optional)lh all te alt stop
3.lh mod te e trace1 UEH_EXCEPTION
4.lh mod te e trace3 IU_IF

5.lh mod te s UEH_EXCEPTION

6.lh mod te s IU_IF

7.Tp machine> ps -ef |egrep -i logsp

8.Tp machine> kill -9 <processID>

9.
<<< RNC3810 >>>
Tokyo, tp03)/export/home/tpuser/users/p3/bin/startmon4.sh trncxx
Tokai, tp03)/export/home/tpuser/users/p3/bin/startmon4.sh crncxxx
Kansai, tp01)/export/home/tpuser/users/p3/bin/startmon4.sh krncxxx
<<< RNC3820 >>>
Tokyo, tp03)/export/home/tpuser/users/p3/bin/startmon4_3820.sh trncxx
Tokai, tp03)/export/home/tpuser/users/p3/bin/startmon4_3820.sh crncxxx
Kansai, tp01)/export/home/tpuser/users/p3/bin/startmon4_3820.sh krncxxx

5.11Confirm Upgrade and monitor upgrade status

sget UpgradePackage=CXP9014711/4_R2EA prog|stat

acc UpgradePackage=CXP9014711/4_R2EA confirmupgrade

sget UpgradePackage=CXP9014711/4_R2EA prog|stat

5.13Check the KPI after RNC restart

1.pmrup -m 1
(0.25 and 0.5 should be used 1st and 2nd ROP)

5.14Activate the User defined PM scanner

1.pst

5.15Check and WA for RANAP high load

<RNC3810>
1. each capi check
lh ranapmp capi tot
lh ranapmp capi tot
lh ranapmp capi prio--> select high load pri -> x
lh ranapmp capi type pri <x>
lh ranapmp capi tot
lh ranapmp capi tot
lh ranapmp capi prio--> select high load pri -> y
lh ranapmp capi type pri <y>
<RNC3820>
1. each capi check
lh sccpmp capi tot
lh sccpmp capi tot
lh sccpmp capi prio--> select high load pri -> x
lh sccpmp capi type pri <x>
lh sccpmp capi tot
lh sccpmp capi tot
lh sccpmp capi prio--> select high load pri -> y
lh sccpmp capi type pri <y>

2.pmr -m 1>>> select 3) check IuSigSuc

3.sget <upgradepackage MO> prog|state
4.acc 001700 manualrestart
5.lh ranapmp sma -all
6.lt ranap
7.st ranap
8.lk ranap

<RNC3810>
9. each capi check
lh ranapmp capi tot
lh ranapmp capi tot
lh ranapmp capi prio--> select high load pri -> x
lh ranapmp capi type pri <x>
lh ranapmp capi tot
lh ranapmp capi tot
lh ranapmp capi prio--> select high load pri -> y
lh ranapmp capi type pri <y>
<RNC3820>
9. each capi check
lh sccpmp capi tot
lh sccpmp capi tot
lh sccpmp capi prio--> select high load pri -> x
lh sccpmp capi type pri <x>
lh sccpmp capi tot
lh sccpmp capi tot
lh sccpmp capi prio--> select high load pri -> y
lh sccpmp capi type pri <y>

10. cvls
11. acc 0 manualrestart

5.16WA for Ranap disabled after upgrade

1.lt ranap|mtp3b|m3ua|ip|aal|sccp|sctp|atmport
2.alt
3.lst ranap
4.lk Ranap=<target ranap>

5.acl <target m3ua(SGSN1)>

6.acc <target m3ua(SGSN1)> setAutoDown
7.lst M3uAssociation=<target m3ua(SGSN1)>
8.acl <target m3ua(SGSN2)>
9.acc <target m3ua(SGSN2)> setAutoDown
10. lst M3uAssociation=<target m3ua(SGSN2)>

11. acl <target m3ua(SGSN1)>

12. acc <target m3ua(SGSN1)> setAutoActivate
13. lst M3uAssociation=<target m3ua(SGSN1)>
14. acl <target m3ua(SGSN2)>
15. acc <target m3ua(SGSN2)> setAutoActivate
16. lst M3uAssociation=<target m3ua(SGSN2)>

17. alt
18. lst ranap
19. lk Ranap=<target ranap>

20. u+ ranap_rec
21. del ranap=<target ranap>
22. u-
23. run <created mos>

24. alt
25. lst ranap
26. lk ranap=<target ranap>

5.17WA for Synchronization alarms from DUW sites

(RBS operation)
1.alt
2.sget Synchronization
3.rm /d/nss_tum_data.
4.cvls
5.acc 0 manualrestart
6.alt
7.sget Synchronization

5.18WA for DISABLED cells without alarm after upgrade

1.st utarncell=<target sites>

(Optional)
lh <MOD> te e trace1 trace6 trace7 DLCODE_CELL
lh <MOD> te e trace3 trace6 trace7 HSDSCH_CONFIG_CELL
lh <MOD> te e trace5 trace6 trace7 rnhCellRoC[<CELL_RO>]
lh ommp te e trace6 trace7 roamFroUtranCellRoProxyC
lh ommp te e trace6 trace7 roamFroHsdschRoRnhProxyC
lh <MOD> cellenable -cid <CELL_ID>

lh <MOD> rrt-RncLmCell info 1/1/1/1/2/1.<CELL_CAPS>/6

lh <MOD> rrt-RncLmCell history 1/1/1/1/2/1.<CELL_CAPS>/6
lh <MOD> rrt-RncLmCell system 1/1/1/1
lh <MOD> rrt-RncLmCell getattr 1/1/1/1/2/1.<CELL_CAPS> cellAlarmList
lh <MOD> rrt-RncLmCell history 1/1/1/1/2/1.<CELL_CAPS>
fget <AFFECTED_HSDSCH> froId

<MOD>, <CELL_ID>, CELL_CAPS> - on cedr printout pick affected cell and use values from proper columns:
<MOD> - 'MOD' column
<CELL_ID> - 'cid' column
<CELL_RO> - value from 'ro' column
<CELL_CAPS> - 'ro' column increased by 1 ('ro' + 1)

After finished taking the log, need to disable traces

h <MOD> te d trace1 trace6 trace7 DLCODE_CELL
lh <MOD> te d trace3 trace6 trace7 HSDSCH_CONFIG_CELL
lh <MOD> te d trace5 trace6 trace7 rnhCellRoC[<CELL_RO>]
lh ommp te d trace6 trace7 roamFroUtranCellRoProxyC
lh ommp te d trace6 trace7 roamFroHsdschRoRnhProxyC
lh <MOD> celldisable -cid <CELL_ID>

2.bl <target hsdsch>

3.deb <target hsdsch>
4.bl <target utrancell>
5.deb <target utrancell>

6.lbl <target utrancell>

7.deb <target commonCH>
8.deb <target utrancell>
9.deb <target hsdsch>
10. deb <target eul>

11. bl <target hsdsch> <target Eul>

12. u+
13. del <Eul on target cell>
14. del <Hsdsch on target cell>
15. u-
16. run <created mos>
17. deb <target hsdsch> <target Eul>

18. cvls
19. acc 0 manualrestart

20. strt
21. acc mod<target mod> manualrestart
22. st utrancell

5.19WA for RBS alarm ?gCarrier_RejectSignalFromHardware?h

(RNC)
1.lt ^utrancell|fach|rach|^pch|hsdsch|eul
2.lst utrancell=<target site>
3.alt
(RBS)
4.alt
5.cvls
6.acc 0 manualrestart
7.cvls
(RNC)
8.alt
9.lst utrancell=<target site>
(RBS)
10. alt

5.20WA for RBS alarm NodeSynch_Phase_Difference_Measurement_Failed

1)Check if the alarm appeared from all RBS or not.

- If all the alarm appears from all RBS, Restart active TUB borad.
cab
bl 000400
st 000400
acc 000400 manualrestart

2)Check which subracks the impacted RBS refer to.

strt
sget IubLink=XXX|XXX|XXX rncModuleRef
(XXX = iublink name)
st modX
##or
std

3)Check which Ccdevices the impacted RBS use

cedr | sort -k 27 | egrep -i "XXX|XXX|XXX"
(XXX = cell name)

- If the impacted RBS use a same Ccdevice, restart SPB board which has the Ccdevice
bl (target board name)
st XXX
acc XXX manualrestart

4)Check if the impacted RBS are ATM RBS or IP RBS.

strt -s XXX
XXX = ms, es-1 (target subrack)

5.21Check and WA for WCDMA carrier issue

1.shget wcdmacarrier
2.
ex) perl ichigo_wcdmacarrier_detection_paX.pl -rnc krnc569 -carrier 5,6
Tokyo, tp03)cd /home/tpuser/users/emotshi/111124_TRNC83_wcdmacarrier/
perl ichigo_wcdmacarrier_detection_pa7.pl -rnc trncxx -carrier 5,6

######not confirmed below yet #####################

Tokai, tp03)cd /home/tpuser/users/ichigo
perl ichigo_wcdmacarrier_detection_pa6.pl -rnc crncxx -carrier 5,6
Kansai,tp01)cd /home/tpuser/users/ichigo
perl ichigo_wcdmacarrier_detection_pa6.pl -rnc krncxx -carrier 5,6
###################################################

3.
tpuser@nrjtotp03 trnc83]$ gzip -dc 2011-11-25_120* | /opt/tools/decoder/3.1t/decoder/concat_segmented_rlib_traces.pl
| grep -i wcdmacarrier
ex)
[2011-11-25 03:04:47.832] 010200/RncLmUePT(uehUeCtxtFroObjectWcdmaCarrierC)
../src/UehUeCtxtFroObjectWcdmaCarrierC.cpp:140 ERROR:setWcdmaCarrierValidData(): could not retrive data from config
for FRO id = 4
[2011-11-25 03:07:31.380] 010200/RncLmUePT(uehUeCtxtFroObjectWcdmaCarrierC)
../src/UehUeCtxtFroObjectWcdmaCarrierC.cpp:140 ERROR:setWcdmaCarrierValidData(): could not retrive data from config
for FRO id = 5
4.
ex) perl ichigo_wcdmacarrier_remedy_paX.pl -rnc krnc569 -carrier 1,2,3,4,5,6
Tokyo, tp03)perl ichigo_wcdmacarrier_remedy_pa4.pl -rnc trncxx -carrier 1,2,3,4,5,6

######not confirmed below yet #####################

Tokai, tp03)perl ichigo_wcdmacarrier_remedy_pa4.pl -rnc crncxx -carrier 1,2,3,4,5,6
Kansai,tp01)perl ichigo_wcdmacarrier_remedy_pa4.pl -rnc krncxx -carrier 1,2,3,4,5,6
###################################################

5.
ex) perl ichigo_wcdmacarrier_detection_paX.pl -rnc krnc569 -carrier 1,2,3,4,5,6
Tokyo, tp03)cd /home/tpuser/users/emotshi/111124_TRNC83_wcdmacarrier/
perl ichigo_wcdmacarrier_detection_pa7.pl -rnc trncxx -carrier 1,2,3,4,5,6

######not confirmed below yet #####################

Tokai, tp03)cd /home/tpuser/users/ichigo
perl ichigo_wcdmacarrier_detection_pa6.pl -rnc crncxx -carrier 1,2,3,4,5,6
Kansai,tp01)cd /home/tpuser/users/ichigo
perl ichigo_wcdmacarrier_detection_pa6.pl -rnc krncxx -carrier 1,2,3,4,5,6
###################################################

6.
tpuser@nrjtotp03 trnc83]$ gzip -dc 2011-11-25_120* | /opt/tools/decoder/3.1t/decoder/concat_segmented_rlib_traces.pl
| grep -i wcdmacarrier
ex)
[2011-11-25 03:04:47.832] 010200/RncLmUePT(uehUeCtxtFroObjectWcdmaCarrierC)
../src/UehUeCtxtFroObjectWcdmaCarrierC.cpp:140 ERROR:setWcdmaCarrierValidData(): could not retrive data from config
for FRO id = 1
[2011-11-25 03:07:31.380] 010200/RncLmUePT(uehUeCtxtFroObjectWcdmaCarrierC)
../src/UehUeCtxtFroObjectWcdmaCarrierC.cpp:140 ERROR:setWcdmaCarrierValidData(): could not retrive data from config
for FRO id = 2
[2011-11-25 03:04:47.832] 010200/RncLmUePT(uehUeCtxtFroObjectWcdmaCarrierC)
../src/UehUeCtxtFroObjectWcdmaCarrierC.cpp:140 ERROR:setWcdmaCarrierValidData(): could not retrive data from config
for FRO id = 3
[2011-11-25 03:07:31.380] 010200/RncLmUePT(uehUeCtxtFroObjectWcdmaCarrierC)
../src/UehUeCtxtFroObjectWcdmaCarrierC.cpp:140 ERROR:setWcdmaCarrierValidData(): could not retrive data from config
for FRO id = 4
[2011-11-25 03:04:47.832] 010200/RncLmUePT(uehUeCtxtFroObjectWcdmaCarrierC)
../src/UehUeCtxtFroObjectWcdmaCarrierC.cpp:140 ERROR:setWcdmaCarrierValidData(): could not retrive data from config
for FRO id = 5
[2011-11-25 03:07:31.380] 010200/RncLmUePT(uehUeCtxtFroObjectWcdmaCarrierC)
../src/UehUeCtxtFroObjectWcdmaCarrierC.cpp:140 ERROR:setWcdmaCarrierValidData(): could not retrive data from config
for FRO id = 6

7.shget wcdmacarrier

5.23.2tnResAllocSrbHspa parameter check

lt RabHandling
sget RabHandling=1 tnResAllocSrbHspa

============================================================================================
6Health Check After Upgrade
============================================================================================

6.1Check overall RNC traffic status

1.pmrup -m 1

6.2.1Get MO dump
<<< RNC3810 >>>
Terminal 1
1.l+m [Node]_dump_[SWname]_afterUp.log
2.lhsh 001200 capi prio
3.lt all
4.lhsh 001200 capi prio
5.kget
6.lhsh 001200 capi prio
7.l-

Terminal 2
1.l+ [Node]_dump_[SWname]_afterUp_ldmon.log
2.for 2000
3.lhsh 001200 capi prio
4.done

<<< RNC3820 >>>

Terminal 1
1.l+m [Node]_dump_[SWname]_beforeUp.log
2.lhsh 000500 capi prio
3.lt all
4.lhsh 000500 capi prio
5.kget
6.lhsh 000500 capi prio
7.l-

Terminal 2
1.l+ [Node]_dump_[SWname]_beforeUp_ldmon.log
2.for 2000
3.lhsh 000500 capi prio
4.done

6.3.1Check Cell/Link/Device status

< Read MO's ><1>
1.lt ^utrancell|^pch|rach|fach|hsdsch|eul|iublink|nbap|nodesync
2.lt mtp3b|sccp|m3ua|sctp|ranap|rnsap|gigabit|ipacc|ipinter|ipeth|ether|vcltp
3.lt ccdev|dcdev|pdr|packetd|spm|plugin|spdev|rncfeature|stp|aal|upgradepa

< Alarm ><2>

1.alt

< Link status ><3>

1.st sccp|mtp3b|m3ua|sctp|ranap|rnsap
2.st sccp|mtp3b|m3ua|sctp|ranap|rnsap dis

3.st iublink
4.st iublink dis
5.lst iublink dis

6.lst vcltp dis

7.pget m3ua|sctp

8.st gigabit|ipaccesshost

9.sget GigaBitEthernet link.state|activelink

10. sget ipint.* (0|1)state

11. st IpEthPacketDataRouter

12. pmx IpEthPacketDataRouter

< Traffic status ><4>

1.lh ranapmp ueregprint sum
2.lh ranapmp ranap status
3.lh ranapmp ranap conn
4.lh ranapmp rnsap status
5.lh ranapmp rnsap dumpRoTable

< Cell status ><5>

1.st utrancell
2.st utrancell dis
3.lst utrancell
4.lst utrancell dis
5.str

< Device status ><6>

1.st ccdev|dcdev|pdr|packetd|spm|plugin
2.st ccdev|dcdev|pdr|packetd|spm|plugin dis
3.std
4.lh mod drh_dcrh_topdata
5.sget spdevicepool
6.lh mod drh_ccrh_topdata
7.cedr
8.lh mod drh_trbr_data iphost

< Other status ><7>

1.cabx
2.lgaevsmor 5h
3.lgusrm 5h
4.lh all llog -l
5.cabr
6.dump list -a
7.all err
8.hget rncfeature state
9.readclock

10. lst EthernetSwitchPort

11. sget switchportstp stprole
12. each capi check
lh ranapmp capi tot
lh ranapmp capi tot
lh ranapmp capi prio--> select high load pri -> x
lh ranapmp capi type pri <x>
lh ranapmp capi tot
lh ranapmp capi tot
lh ranapmp capi prio--> select high load pri -> y
lh ranapmp capi type pri <y>
13. invr
14. sget switchportstp manualpathcost
15. sget RabHandling=1 maxAllowedGbrUlPsSpeech

< Disk capacity ><8>

1.cabd
2.lh coremp vols /c
3.lh coremp vols /d
4.lh coremp ls /c/loadmodules |awk '{print $1}' |uniq -c
5.lh coremp ls /d/loadmodules |awk '{print $1}' |uniq -c

< Check trace status ><9>

1.lh mp te s -restart
2.cabe (if using latest moshell, lh mp fte s.

< DB check ><10> only daytime

1.ftget /d/configuration/cv/<latest CV name
2.nowshell -d db.dat (from cv folder on tp server.
3.dbc db.dat (on offline mode.

6.3.2Check the status of Reliable Programs

1.lh mp sma -all

6.6.2Check final CV
1.lh coremp cv csum <xRNCxx>
============================================================================================
8Rollback
============================================================================================

8.2.1Check the UE connectivity to the Core network

<<< RNC3810 >>>
1.l+ xrncxx_PostQHC.log
2.lhsh 001700 ueregprint sum
3.lhsh 001700 ranap status
4.lhsh 001700 ranap conn
5.lhsh 001800 rnsap status
6.lhsh 001800 rnsap conn
7.lgevsmur 30m
<<< RNC3820 W10B CU3 EU11 >>>
1.l+ xrncxx_PostQHC.log
2.lhsh 000700 ueregprint sum
3.lhsh 000700 ranap status
4.lhsh 000700 ranap conn
5.lhsh 000700 rnsap status
6.lhsh 000700 rnsap conn
7.lgevsmur 30m
<<< RNC3820 W10B AD78, W11B >>>
1.l+ xrncxx_PostQHC.log
2.lhsh 002200 ueregprint sum
3.lhsh 000700 ranap status
4.lhsh 000700 ranap conn
5.lhsh 002200 rnsap status
6.lhsh 002200 rnsap conn
7.lgevsmur 30m

8.2.2ET-M4 Overload
1.lgsemr 10m
2.lhsh xxxxxx(target ETB) capi tot

8.2.3Check program crashes after Upgrade (CSR1783379)

1.lgsemr 10m
2.lgsemr 10m
3.cv cu

(RNC3810)
4.lhsh 001000 sma -all
lhsh 001100 sma -all
5.cv cu
6.lgsemr 10m
7.lhsh 001000 sma -all
lhsh 001100 sma -all
alt
8.lst 001000
9.bl 001000
10. lst 001000
11. lhsh 001000 sma -all
lhsh 001100 sma -all
12. alt
13. lst 001000
14. deb 001000
15. lst 001000
16. lgsemr 10m
17. lhsh 001000 sma -all
lhsh 001100 sma -all

(RNC3820)
4.lhsh 000500 sma -all
lhsh 002400 sma -all
5.cv cu
6.lgsemr 10m
7.lhsh 000500 sma -all
lhsh 002400 sma -all
alt
8.lst 000500
9.bl 000500
10. lst 000500
11. lhsh 000500 sma -all
lhsh 002400 sma -all
12. alt
13. lst 000500
14. deb 000500
15. lst 000500
16. lgsemr 10m
17. lhsh 000500 sma -all
lhsh 002400 sma -all

8.2.4Confirm Mirroring to be finished

1.lh coremp mirror s
2.getAttrObj me

8.2.5Normality check
< Read MO's ><1>
1.lt ^utrancell|^pch|rach|fach|hsdsch|eul|iublink|nbap|nodesync
2.lt mtp3b|sccp|m3ua|sctp|ranap|rnsap|gigabit|ipacc|ipinter|ipeth|ether|vcltp
3.lt ccdev|dcdev|pdr|packetd|spm|plugin|spdev|rncfeature

< Alarm ><2>

1.alt

< Link status ><3>

1.st sccp|mtp3b|m3ua|sctp|ranap|rnsap dis
2.st gigabit|ipaccesshost
3.sget GigaBitEthernet link.state|activelink
4.sget ipint.* (0|1).state
5.st IpEthPacketDataRouter
6.lpget m3ua pmnoofdatamsg
(Check the counter values increases gradually)

< Cell status ><4>

1.st utrancell dis
2.lst utrancell|pch|rach|fach|hsdsch|eul dis
3.str

< Device status ><5>

1.st ccdev|dcdev|pdr|packetd|spm|plugin dis
2.std

< Other status ><6>

1.lgaevsmour 1h
2. each capi check (Repeat the following for 3 times)
lh sccpmp capi tot
lh sccpmp capi tot
lh sccpmp capi prio--> select high load pri -> x
lh sccpmp capi type pri <x>
lh sccpmp capi tot
lh sccpmp capi tot
lh sccpmp capi prio--> select high load pri -> y
lh sccpmp capi type pri <y>
8.3Take the node trace logs
1.vii
2.run dcg_datacollection_8.0r_modified_110608.mos <A> <B> e
<A> Path of the log output.
<B> Node name. (used for log file naming)
3.(only 3810)
run dcg_script_noOMS_version_090813_ES3_4_ver6.mos
run dcg_script_noOMS_version_090813_ES11_12_ver6.mos

8.5Switch Targetmonitor to Standby coreMP

1.lt ReliableProgramUniter
2.pr ReliableProgramUniter
3.lh coremp sma -all(Find the targetmonitor RPU)
4.lsget ReliableProgramUniter userLabel target
5.sget ReliableProgramUniter=xxxxxxxx
(xxxx = ReliableProgramUniterId)

6.acl ReliableProgramUniter=xxxxxxxxxxx
(xxxx = ReliableProgramUniterId)
7.acc ReliableProgramUniter=xxxxxxxxxxx switch
(xxxx = ReliableProgramUniterId)
8.sget ReliableProgramUniter=xxxxxxxx
9.lsget ReliableProgramUniter userLabel target
10. lh coremp sma -all(Find the targetmonitor RPU)

<<< RNC3810 >>>

11. sgetReliableProgramUniter=xxxxxx
12. set ReliableProgramUniter=xxxxxxx admActiveSlot Subrack=MS,Slot=11
13. set ReliableProgramUniter=xxxxxxx admPassiveSlot Subrack=MS,Slot=10
14. sgetReliableProgramUniter=xxxxxx
(confirm right configuration)
<<< RNC3820 >>>
11. sgetReliableProgramUniter=xxxxxx
12. set ReliableProgramUniter=xxxxxxx admActiveSlot Subrack=MS,Slot=24
13. set ReliableProgramUniter=xxxxxxx admPassiveSlot Subrack=MS,Slot=5
14. sgetReliableProgramUniter=xxxxxx
(confirm right configuration)

15. lh coremp sma -all

(Find the targetmonitor RPU)

(Extra info)
<<< RNC3810 >>>
1.lhsh 001000 sma -all
2.sget ReliableProgramUniter rpuid <RPU id>
3.sget ReliableProgramUniter=<MO identity>
<<< RNC3820 >>>
1.lhsh 000500 sma -all
2.sget ReliableProgramUniter rpuid <RPU id>
3.sget ReliableProgramUniter=<MO identity>

8.6Activate the DailyTrace

1.lh all te alt status |egrep overload
2.(optional)lh all te alt stop
3.lh mod te e trace1 UEH_EXCEPTION
4.lh mod te e trace3 IU_IF

5.lh mod te s UEH_EXCEPTION

6.lh mod te s IU_IF

7.Tp machine> ps -ef |egrep -i logsp

8.Tp machine> kill -9 <processID>

9.
<<< RNC3810 >>>
Tokyo, tp04)/export/home/tpuser/users/p3/bin/startmon4.sh trncxx
Tokai, tp03)/export/home/tpuser/users/p3/bin/startmon4.sh crncxxx
Kansai, tp01)/export/home/tpuser/users/p3/bin/startmon4.sh krncxxx
<<< RNC3820 >>>
Tokyo, tp04)/export/home/tpuser/users/p3/bin/startmon4_3820.sh trncxx
Tokai, tp03)/export/home/tpuser/users/p3/bin/startmon4_3820.sh crncxxx
Kansai, tp01)/export/home/tpuser/users/p3/bin/startmon4_3820.sh krncxxx
8.7Check the KPI after RNC restart
1.pmrup -m 1
(0.25 and 0.5 should be used 1st and 2nd ROP)

8.8Activate the User defined PM scanner

1.pst

8.9Check and WA for RANAP high load

<<< RNC3810 >>>
1. each capi check
lhsh 001700 capi tot
lhsh 001700 capi tot
lhsh 001700 capi prio--> select high load pri -> x
lhsh 001700 capi type pri <x>
lhsh 001800 capi tot
lhsh 001800 capi tot
lhsh 001800 capi prio--> select high load pri -> y
lhsh 001800 capi type pri <y>
<<< RNC3820 >>>
1. each capi check
lhsh 000700 capi tot
lhsh 000700 capi tot
lhsh 000700 capi prio--> select high load pri -> x
lhsh 000700 capi type pri <x>
lhsh 002200 capi tot
lhsh 002200 capi tot
lhsh 002200 capi prio--> select high load pri -> y
lhsh 002200 capi type pri <y>
2.pmr -m 1>>> select 3) check IuSigSuc
3.sget <upgradepackage MO> prog|state
4.acc 001700 manualrestart
5.lh ranapmp sma -all
6.lt ranap
7.st ranap
8.lk ranap
<<< RNC3810 >>>
9. each capi check
lhsh 001700 capi tot
lhsh 001700 capi tot
lhsh 001700 capi prio--> select high load pri -> x
lhsh 001700 capi type pri <x>
lhsh 001800 capi tot
lhsh 001800 capi tot
lhsh 001800 capi prio--> select high load pri -> y
lhsh 001800 capi type pri <y>
<<< RNC3820 >>>
9. each capi check
lhsh 000700 capi tot
lhsh 000700 capi tot
lhsh 000700 capi prio--> select high load pri -> x
lhsh 000700 capi type pri <x>
lhsh 002200 capi tot
lhsh 002200 capi tot
lhsh 002200 capi prio--> select high load pri -> y
lhsh 002200 capi type pri <y>

10. cvls
11. acc 0 manualrestart

8.10WA for Ranap disabled after upgrade

1.lt ranap|mtp3b|m3ua|ip|aal|sccp|sctp|atmport
2.alt
3.lst ranap
4.lk Ranap=<target ranap>

5.acl <target m3ua(SGSN1)>

6.acc <target m3ua(SGSN1)> setAutoDown
7.lst M3uAssociation=<target m3ua(SGSN1)>
8.acl <target m3ua(SGSN2)>
9.acc <target m3ua(SGSN2)> setAutoDown
10. lst M3uAssociation=<target m3ua(SGSN2)>

11. acl <target m3ua(SGSN1)>

12. acc <target m3ua(SGSN1)> setAutoActivate
13. lst M3uAssociation=<target m3ua(SGSN1)>
14. acl <target m3ua(SGSN2)>
15. acc <target m3ua(SGSN2)> setAutoActivate
16. lst M3uAssociation=<target m3ua(SGSN2)>

17. alt
18. lst ranap
19. lk Ranap=<target ranap>

20. u+ ranap_rec
21. del ranap=<target ranap>
22. u-
23. run <created mos>

24. alt
25. lst ranap
26. lk ranap=<target ranap>

8.11WA for Synchronization alarms from DUW sites

(RBS operation)
1.alt
2.sget Synchronization
3.rm /d/nss_tum_data.
4.cvls
5.acc 0 manualrestart
6.alt
7.sget Synchronization

8.12WA for DISABLED cells without alarm after upgrade

1.st utarncell=<target sites>

(Optional)
lh <MOD> te e trace1 trace6 trace7 DLCODE_CELL
lh <MOD> te e trace3 trace6 trace7 HSDSCH_CONFIG_CELL
lh <MOD> te e trace5 trace6 trace7 rnhCellRoC[<CELL_RO>]
lh ommp te e trace6 trace7 roamFroUtranCellRoProxyC
lh ommp te e trace6 trace7 roamFroHsdschRoRnhProxyC
lh <MOD> cellenable -cid <CELL_ID>

lh <MOD> rrt-RncLmCell info 1/1/1/1/2/1.<CELL_CAPS>/6

lh <MOD> rrt-RncLmCell history 1/1/1/1/2/1.<CELL_CAPS>/6
lh <MOD> rrt-RncLmCell system 1/1/1/1
lh <MOD> rrt-RncLmCell getattr 1/1/1/1/2/1.<CELL_CAPS> cellAlarmList
lh <MOD> rrt-RncLmCell history 1/1/1/1/2/1.<CELL_CAPS>
fget <AFFECTED_HSDSCH> froId

<MOD>, <CELL_ID>, CELL_CAPS> - on cedr printout pick affected cell and use values from proper columns:
<MOD> - 'MOD' column
<CELL_ID> - 'cid' column
<CELL_RO> - value from 'ro' column
<CELL_CAPS> - 'ro' column increased by 1 ('ro' + 1)

After finished taking the log, need to disable traces

h <MOD> te d trace1 trace6 trace7 DLCODE_CELL
lh <MOD> te d trace3 trace6 trace7 HSDSCH_CONFIG_CELL
lh <MOD> te d trace5 trace6 trace7 rnhCellRoC[<CELL_RO>]
lh ommp te d trace6 trace7 roamFroUtranCellRoProxyC
lh ommp te d trace6 trace7 roamFroHsdschRoRnhProxyC
lh <MOD> celldisable -cid <CELL_ID>

2.bl <target hsdsch>

3.deb <target hsdsch>
4.bl <target utrancell>
5.deb <target utrancell>

6.lbl <target utrancell>

7.deb <target commonCH>
8.deb <target utrancell>
9.deb <target hsdsch>
10. deb <target eul>

11. bl <target hsdsch> <target Eul>

12. u+
13. del <Eul on target cell>
14. del <Hsdsch on target cell>
15. u-
16. run <created mos>
17. deb <target hsdsch> <target Eul>
18. cvls
19. acc 0 manualrestart

20. strt
21. acc mod<target mod> manualrestart
22. st utrancell

8.13WA for RBS alarm ?gCarrier_RejectSignalFromHardware?h

(RNC)
1.lt ^utrancell|fach|rach|^pch|hsdsch|eul
2.lst utrancell=<target site>
3.alt
(RBS)
4.alt
5.cvls
6.acc 0 manualrestart
7.cvls
(RNC)
8.alt
9.lst utrancell=<target site>
(RBS)
10. alt

8.16WA for RBS alarm NodeSynch_Phase_Difference_Measurement_Failed

1)Check if the alarm appeared from all RBS or not.

- If all the alarm appears from all RBS, Restart active TUB borad.
cab
bl 000400
st 000400
acc 000400 manualrestart

2)Check which subracks the impacted RBS refer to.

strt
sget IubLink=XXX|XXX|XXX rncModuleRef
(XXX = iublink name)
st modX
##or
std

3)Check which Ccdevices the impacted RBS use

cedr | sort -k 27 | egrep -i "XXX|XXX|XXX"
(XXX = cell name)

- If the impacted RBS use a same Ccdevice, restart SPB board which has the Ccdevice
bl (target board name)
st XXX
acc XXX manualrestart

4)Check if the impacted RBS are ATM RBS or IP RBS.

strt -s XXX
XXX = ms, es-1 (target subrack)

8.17Check and WA for WCDMA carrier issue

1.shget wcdmacarrier
2.
ex) perl ichigo_wcdmacarrier_detection_paX.pl -rnc krnc569 -carrier 5,6
Tokyo, tp03)cd /home/tpuser/users/emotshi/111124_TRNC83_wcdmacarrier/
perl ichigo_wcdmacarrier_detection_pa7.pl -rnc trncxx -carrier 5,6

######not confirmed below yet #####################

Tokai, tp03)cd /home/tpuser/users/ichigo
perl ichigo_wcdmacarrier_detection_pa6.pl -rnc crncxx -carrier 5,6
Kansai,tp01)cd /home/tpuser/users/ichigo
perl ichigo_wcdmacarrier_detection_pa6.pl -rnc krncxx -carrier 5,6
###################################################

3.
tpuser@nrjtotp03 trnc83]$ gzip -dc 2011-11-25_120* | /opt/tools/decoder/3.1t/decoder/concat_segmented_rlib_traces.pl
| grep -i wcdmacarrier
ex)
[2011-11-25 03:04:47.832] 010200/RncLmUePT(uehUeCtxtFroObjectWcdmaCarrierC)
../src/UehUeCtxtFroObjectWcdmaCarrierC.cpp:140 ERROR:setWcdmaCarrierValidData(): could not retrive data from config
for FRO id = 4
[2011-11-25 03:07:31.380] 010200/RncLmUePT(uehUeCtxtFroObjectWcdmaCarrierC)
../src/UehUeCtxtFroObjectWcdmaCarrierC.cpp:140 ERROR:setWcdmaCarrierValidData(): could not retrive data from config
for FRO id = 5
4.
ex) perl ichigo_wcdmacarrier_remedy_paX.pl -rnc krnc569 -carrier 1,2,3,4,5,6
Tokyo, tp03)perl ichigo_wcdmacarrier_remedy_pa4.pl -rnc trncxx -carrier 1,2,3,4,5,6

######not confirmed below yet #####################

Tokai, tp03)perl ichigo_wcdmacarrier_remedy_pa4.pl -rnc crncxx -carrier 1,2,3,4,5,6
Kansai,tp01)perl ichigo_wcdmacarrier_remedy_pa4.pl -rnc krncxx -carrier 1,2,3,4,5,6
###################################################

5.
ex) perl ichigo_wcdmacarrier_detection_paX.pl -rnc krnc569 -carrier 1,2,3,4,5,6
Tokyo, tp03)cd /home/tpuser/users/emotshi/111124_TRNC83_wcdmacarrier/
perl ichigo_wcdmacarrier_detection_pa7.pl -rnc trncxx -carrier 1,2,3,4,5,6

######not confirmed below yet #####################

Tokai, tp03)cd /home/tpuser/users/ichigo
perl ichigo_wcdmacarrier_detection_pa6.pl -rnc crncxx -carrier 1,2,3,4,5,6
Kansai,tp01)cd /home/tpuser/users/ichigo
perl ichigo_wcdmacarrier_detection_pa6.pl -rnc krncxx -carrier 1,2,3,4,5,6
###################################################

6.
tpuser@nrjtotp03 trnc83]$ gzip -dc 2011-11-25_120* | /opt/tools/decoder/3.1t/decoder/concat_segmented_rlib_traces.pl
| grep -i wcdmacarrier
ex)
[2011-11-25 03:04:47.832] 010200/RncLmUePT(uehUeCtxtFroObjectWcdmaCarrierC)
../src/UehUeCtxtFroObjectWcdmaCarrierC.cpp:140 ERROR:setWcdmaCarrierValidData(): could not retrive data from config
for FRO id = 1
[2011-11-25 03:07:31.380] 010200/RncLmUePT(uehUeCtxtFroObjectWcdmaCarrierC)
../src/UehUeCtxtFroObjectWcdmaCarrierC.cpp:140 ERROR:setWcdmaCarrierValidData(): could not retrive data from config
for FRO id = 2
[2011-11-25 03:04:47.832] 010200/RncLmUePT(uehUeCtxtFroObjectWcdmaCarrierC)
../src/UehUeCtxtFroObjectWcdmaCarrierC.cpp:140 ERROR:setWcdmaCarrierValidData(): could not retrive data from config
for FRO id = 3
[2011-11-25 03:07:31.380] 010200/RncLmUePT(uehUeCtxtFroObjectWcdmaCarrierC)
../src/UehUeCtxtFroObjectWcdmaCarrierC.cpp:140 ERROR:setWcdmaCarrierValidData(): could not retrive data from config
for FRO id = 4
[2011-11-25 03:04:47.832] 010200/RncLmUePT(uehUeCtxtFroObjectWcdmaCarrierC)
../src/UehUeCtxtFroObjectWcdmaCarrierC.cpp:140 ERROR:setWcdmaCarrierValidData(): could not retrive data from config
for FRO id = 5
[2011-11-25 03:07:31.380] 010200/RncLmUePT(uehUeCtxtFroObjectWcdmaCarrierC)
../src/UehUeCtxtFroObjectWcdmaCarrierC.cpp:140 ERROR:setWcdmaCarrierValidData(): could not retrive data from config
for FRO id = 6

7.shget wcdmacarrier

==========================================================================