Scribd
Upload
227 views2 pages

Polymer Modified Structural Repair 1241 25

This document provides information about QUIKRETE Polymer Modified Structural Repair, a polymer modified and shrinkage-compensated rapid setting, high strength concrete repair material. It describes the product, including its uses, size, yield, technical data, and installation instructions.

Uploaded by

miguelq_scribd
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
227 views2 pages

Polymer Modified Structural Repair 1241 25

This document provides information about QUIKRETE Polymer Modified Structural Repair, a polymer modified and shrinkage-compensated rapid setting, high strength concrete repair material. It describes the product, including its uses, size, yield, technical data, and installation instructions.

Uploaded by

miguelq_scribd
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

POLYMER MODIFIED STRUCTURAL DIVISION 3

REPAIR Maintenance of Concrete


03 01 00
P
PRRRO
OD
O DU
D UC
U CT
C TN
T O.. 1
NO
O 1224411--2255,, --5588 Structural Concrete
03 31 00
PRODUCT DESCRIPTION
QUIKRETE® Polymer Modified Structural Repair is a polymer modified and
shrinkage-compensated rapid setting, high strength repair material designed for
vertical and horizontal structural concrete repairs.

PRODUCT USE
QUIKRETE Commercial Grade Polymer Modified Structural Repair
consists of special fast-setting hydraulic cement, graded sands and
other proprietary ingredients. This product is designed to be used for
partial-depth repairs and can be sculpted to match the contour of
existing concrete surfaces. For full-depth repairs, the product should
be expanded with up to 10 lb (4.5 kg) of gravel per 20 lb (9.1 kg) of
product.

SIZE
QUIKRETE Polymer Modified Structural Repair - 20 lb (9.1 kg) pails INSTALLATION
and 50 lb (22.7 kg) bags. SURFACE PREPARATION
• Remove all spalled and unsound concrete from area to be repaired.
YIELD • If rusty reinforcing steel is present, it must be abrasive blasted to
A 20 lb (9.1 kg) pail of QUIKRETE Polymer Modified Structural remove rust. Wear proper personal protective equipment. Remove
Repair will yield approximately 0.17 cu ft (4.8 L) of material. A 50 lb enough material to completely expose the reinforcing steel.
(22.7 kg) bag of QUIKRETE Polymer Modified Structural Repair will • Large vertical patches deeper than 2 in (50 mm) should contain
yield approximately 0.43 cu ft (12.0 L) of material. reinforcing steel. If none is present, new steel should be inserted
using appropriate techniques.
TECHNICAL DATA • Dampen with clean water and remove standing water before
APPLICABLE STANDARDS patching.
ASTM International
• ASTM C109/C109M Standard Test Method for Compressive MIXING
Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube 1. WEAR IMPERVIOUS GLOVES, such as nitrile. Mix by hand or
Specimens) mechanically for a minimum of 3 minutes using a standard mortar
mixer.
PHYSICAL/CHEMICAL PROPERTIES 2. Add 3 pt (1.4 L) of clean water for each 20 lb (9.1 kg) pail. Add the
QUIKRETE® Polymer Modified Structural Repair®, when tested in powder to the water and mix to a stiff gel-like consistency. If mix is too
accordance with ASTM procedures, provides typical results as listed thick, add water sparingly to reach the desired consistency. Do not
in Table 1. mix more material that can be placed in 15 minutes.
3. If the Structural Repair is to be used as a repair material for repairs
TABLE 1 deeper than 2 in (50 mm), up to 10 lb (4.5 kg) of clean, high quality
Typical Compressive Strength (ASTM C109 Modified) -1/2 in (-13 mm) gravel may be added to mix.
4. QUIKRETE® Polymer Modified Structural Repair obtains high bond
3 Hours 2,500 psi (17.2 MPa) strength without the use of bonding adhesives or acrylic additives.
24 Hours 4,000 psi (27.5 MPa) 5. Do not re-temper with additional water.
7 Days 5,500 psi (37.9 Mpa)
28 Days 6,500 psi (44.8 Mpa)
PLACING ASTM C33. Extension by 50% will affect set time and reduce
• Do not apply as a coating. Use for patches less than 2 ft2 (0.19 m2). compressive strengths compared to data presented in Table 1.
• QUIKRETE® Polymer Modified Structural Repair should be trowel Performance and yield will be affected by the characteristics of the
applied to a damp surface. coarse aggregate utilized and water addition. Adjust water to achieve
• Apply a thin layer with heavy trowel pressure and then go back and a slump of about 3 in to 5 in (75 to 125 mm).
build up to the desired thickness.
• After initial set, the material may be trimmed and shaped to match PRECAUTIONS
the contours of the existing patch area. Do not use if temperatures are below 40 °F ( 4 °C ) or are expected
to go below 32 °F ( 0 °C ) within a 24 hour period. Use cold water in
CURING hot weather or hot water in cold weather to achieve desired product
No special curing procedures are required under normal conditions. In temperature.
hot, dry or windy conditions keep the patch covered and damp for at
least 24 hours, or apply QUIKRETE® Acrylic Concrete Cure and Seal WARRANTY
(No. 87300) in accordance with package instructions. NOTICE: Obtain the applicable LIMITED WARRANTY: at
www.quikrete.com/product-warranty or send a written request to The
AGGREGATE EXTENSION Quikrete Companies, LLC, Five Concourse Parkway, Atlanta, GA
For deep patches, QUIKRETE® Polymer Modified Structural Repair 30328, USA. Manufactured under the authority of The Quikrete
may be extended 50% with up to 10 lb (4.5 kg) of minus ½ in (13 mm) Companies, LLC. © 2018 Quikrete International, Inc.
coarse aggregate per 20 lb (9.1 kg) pail. Use well graded, good
quality coarse aggregate, minus ½ in (13 mm) diameter, meeting

* Refer to www.quikrete.com for the most current technical data, SDS, and guide specifications

You might also like