B Series——Waterproof Model

NCB-543W

User Manual
V4.0
http://www.wansview.com

Index

1 INTRODUCTION ...........................................................................................................................4

1.1 THE PACKAGE INCLUDES ..........................................................................................................4

1.2 FUNCTION AND FEATURES ........................................................................................................4
1.3 TECHNICAL PARAMETERS .........................................................................................................5

2 APPEARANCE AND INTERFACE.............................................................................................6

2.1 APPEARANCE ............................................................................................................................6

2.2 INTERFACE OF EQUIPMENT .......................................................................................................6

3 VISIT IP CAMERA FROM LAN ..................................................................................................6

3.1 LAN CONNECTION .....................................................................................................................6

3.2 SEARCH AND SET THE IP ADDRESS OF THE IP CAMERA ...............................................................7
3.3 VISIT IP CAMERA .....................................................................................................................8
3.3.1 Video Play Area ...................................................................................................................8

4 VISIT IP CAMERA FROM WAN ...............................................................................................10

4.1 WAN CONNECTION .................................................................................................................10

4.2 PORT FORWARDING ................................................................................................................10
4.3 DDNS .................................................................................................................................... 11
4.3.1 Manufacturer’s DDNS ....................................................................................................... 11
4.3.2 Third Party DDNS .............................................................................................................12

5 OTHER SETTINGS.....................................................................................................................12

5.1 NETWORK SETTING ................................................................................................................12

5.1.1 Basic Network Setting........................................................................................................12
5.1.2 WIFI Setting.......................................................................................................................12
5.1.3 ADSL Setting......................................................................................................................13
5.1.4 UPnP Setting .....................................................................................................................13
5.1.5 DDNS Setting.....................................................................................................................14
5.1.6 MSN Setting .......................................................................................................................14
5.2 ALARM SETTINGS ...................................................................................................................14
5.2.1 Alarm Setting .....................................................................................................................14
5.2.2 Mail Service Setting ...........................................................................................................16
5.2.3 FTP Service Setting ...........................................................................................................17
5.2.4 Alarm Server......................................................................................................................17
5.3 ADVANCED .............................................................................................................................18
5.3.1 User Setting .......................................................................................................................18
5.3.2 Multi Device Setting ..........................................................................................................18
5.3.3 Other settings.....................................................................................................................19
5.4 MAINTAIN ...............................................................................................................................19
5.4.1 Device Information ............................................................................................................19

2
http://www.wansview.com
5.4.2 Time Setting .......................................................................................................................20
5.4.3 Firmware upgrade .............................................................................................................20
5.4.4 Restore Factory Default.....................................................................................................20
5.4.5 User browsing Log.............................................................................................................20

6 CENTRALIZATION CONTROL ................................................................................................21

7 FAQ ...............................................................................................................................................21

3
http://www.wansview.com

1 Introduction
The IP Camera combines a high quality digital video camera with network connectivity
and a powerful web server to bring clear video to your desktop from anywhere on your
local network or over the Internet.

1.1 The package includes

9 IP Camera * 1
9 IP Camera Utility CD *1
9 5V Power Adapter *1
9 Stand of plastic * 1
9 Cable * 1
NOTE：If you select the device with wifi function, it has built-in wifi module and transmitting
antenna in package.

1.2 Function and Features

9 The video is compressed by MJPEG. There are VGA/QVGA/QQVGA three video
resolutions optional. User can change some parameters according to their demands
to satisfy his own visual prefer.
9 It adopts the TCP/IP network protocols and has inner web server. Users can browse
video through IE and other browsers. Data is transferred through one port; it is easy
for user to do the network setting.
9 Infrared LED for night vision covers 25m area, to realize 24 hours monitoring.
9 Provide IP66 waterproof grade, more suitable for outdoors application.
9 Support 802.11b/g protocol, can build up wireless monitoring.
9 Supports UPNP, port forwarding automatically on the router.
9 Motion detection can find alarm.
9 Alarming record can be sent by email, FTP server. It also sends alarm info to the
alarm server.
9 Support mobile phone to view
9 Support three level of user authority.
9 Support upgrading online.
9 A free DDNS provided by manufacturer, and written in the device.
9 Manufacture provides free software, support Multi-view, Long time recording, video
replay etc.

4
http://www.wansview.com

1.3 Technical Parameters

Item Sub Item Description
Sensor CMOS sensor
Total of pixel 300k
Image Minimum
IR on，0 Lux
Capture illumination
Lens f=4.0mm, F=2.0, Fixed Iris
IR_CUT Support IR and color filter change automatically
Lighting 36pcs 850nm Infrared LEDs, 25m distance
Assistant
Lighting Control Auto control
Resolution 640*480(VGA)/320*240(QVGA)/160*120(QQVGA)
Compression MJPEG
Video and Frame rate 30fps
Audio Bit rate 128kbps ~ 5Mbps
Image Rotation Mirror /Flip
Audio Compression ADPCM
TCP/IP、UDP/IP、HTTP、SMTP、FTP、DHCP、
Basic Protocol
Network DDNS、UPNP、NTP、PPPOE
Other Protocol 802.11b/g
Video control support
Motion Detection support
Triggered Actions Email/FTP /send message to alarm server
Other
User Setting Three levels
Features
Date/ Time Setting support
Upgrade Upgrade from network
DDNS A free DDNS provided by manufacturer
Weight 610g
Main body 185mm(L)*75mm(W)*80mm(H)
Power DC 5V
Physical Power consumption <6W
Index Operating
-20℃~ 50℃
temperature
Operating
10% ~ 80% non-condensing
temperature
OS Supported Microsoft Windows 98/2000/XP/Vista etc.
Internet Explorer6.0 and Above or Compatible
Software(PC Browser
Browser, Firefox, Safari etc.
Side)
Application
IPCMonitor.exe
Software

5
http://www.wansview.com

2 Appearance and interface

2.1 Appearance

Figure 1

2.2 Interface of Equipment

Figure 2

3 Visit IP Camera from LAN

3.1 Lan connection

Figure 3

6
http://www.wansview.com

3.2 Search and set the ip address of the ip camera

Run “BSearch_en.exe” in the CD, the setting interface as figure 4.

Figure 4
Operation Steps:
1) Click “Search (F3)
2) Choose the device
3) Change the ip address of the ip camera according to the information in the red frame
on the left. The numbers in the red circle should not be the same.
4) Put the user name and password into “Authentication” (By default, the user name
is: admin, password is: 123456).
5) Click “Update”
6) After successfully update, click “Search (F3)”, choose the device and click “Browse
(F4)”. Then you may view the ip camera, like figure 5.
NOTE:
1) If you don’t know how to fill out the content of “IP config”, you could also tick the “Set
IP automatically” to get the IP address from the router automatically.
2) If you have the firewall software in your PC, when you run the BSearch_en.exe, it
may pop up a window to say “whether you want to block this program or not”, then
you should choose not to block.
3) The default ip address is 192.168.0.178 and default http port is 80.

7
http://www.wansview.com

Figure 5

3.3 Visit IP Camera

We suggest using IE kernel browser to view the video （it can provide more functions）,
but user need to install Player before viewing the video. Click “download and install
player (first use)” link, it will popup dialogue box as Figure 6, click Run, it will
automatically download player and install.

Figure 6

3.3.1 Video Play Area

After install the plug-ins, click “Mode 1 to view” link in Figure 5 to view the video (video as
Figure 7).

8
http://www.wansview.com

Figure 7
1) Main Menu
The main menu includes the function setting of different submenu
2) Status Displaying Area
In right up corner, it is the status displaying area, to show the 9 devices’ status:
‹ if not connected, button is gray
‹ if connected, button is green
‹ If wrong connected , button is yellow
‹ If alarm , button is red
3) Multi Channel displaying area
If users add multi channel（refer to 5.3.2）, when shift to 4-Ch, 9-CH, and it will
automatically show other devices. You select one device, and you can operate it by
these keys: play, stop, and record, control Pan/tilt, etc.

These buttons mean start video, stop, monitor, talk, record and snapshot.

P.S.: If you want to click this button to record the video, please go to
advanced—Other Settings to set the Record Path first. Please see below figure8.

9
http://www.wansview.com

Figure 8
4) PT and video control
In Pan/Tilt control area, user can control the position according to the arrow sign: up,
down, left, right, middle, horizontal cruise, vertical cruise, and stop etc.

Means open IO output and Close IO output.

User can also set the device frame rate、resolution, brightness, contrast and other parameters.
Note : For this model , no Pan/Tilt ,Alarm I/O function , but you can control other
camera when use multi-view .

4 Visit IP Camera from WAN

4.1 Wan connection

Figure 9

4.2 Port forwarding

If visit IP Camera from WAN, you must do port forwarding on the router. Take Netgear
router for example.

10
http://www.wansview.com

Figure 10
Operation Steps:
1) After login the interface of the router，choose “Port Forwarding”
2) Choose “Add custom Service”
3) Input IP camera port
4) Input IP camera IP address，click “Apply”。（the http port and ip address should be
the same as figure 4 which set by you own)
Note: Different router has different settings for port-forwarding; please kindly
follow your router guide to do the port-forwarding.

After the port-forwarding is done, you could view the IP Camera from WAN now.

4.3 DDNS
You could also use the manufacturer DDNS to view the device as long as your
port-forwarding succeeds.

4.3.1 Manufacturer’s DDNS

Device manufacturer has provided a free DDNS. User can find it in network menu, like
figure 11.

Figure 11

11
http://www.wansview.com
4.3.2 Third Party DDNS
User can also use third part DDNS, such as www.dyndns.com User must apply a free
domain name from this website and fill the info into the below blanks (Figure 12) and
save the settings. Then the domain name can be used.

Figure 12
Note: Using the third party domain name, if the http port is not 80, the port number should
be adding to the domain name with colon. Example: http://btest.dyndns.biz:81.
While manufacturer DDNS is no need to add PORT.

5 Other Settings

5.1 Network Setting

5.1.1 Basic Network Setting
The user can also enter the Basic Network Settings to set the IP address except using
the search software. See below Figure 13.

Figure 13

5.1.2 WIFI Setting

If the device is with WIFI, enter the Wireless LAN Setting, just as below Figure 14 shown,
click the “Scan” button, it will show you all the wireless networks detected in the Wireless
Network List column. Select one of them and tick “Using Wireless Lan”, then the relevant
data of the selected wireless network will be shown in the following blanks. Put in the
password and click “Set”, then the WIFI setting is finished.

12
http://www.wansview.com

Figure 14
Note1: When the device is connected both WIFI and wired, it will firstly connect to the
wired network, if it can’t connect to it, then it will change to connect to the wifi. The
IP address and port is the same, either wireless or wired network.
Note2: Before you do the configuration of wireless as shown above; please make sure
the device is connected to the network via network cable. After settings succeed,
please reboot the device and wireless function takes effect.

5.1.3 ADSL Setting

User could enable the ADSL Dialup according to the below Figure 15 (The ADSL
provider will assign the user name and password to you when you apply for ADSL
service.) Connect the device directly to the ADSL modem and it is connected to the
Internet.

Figure 15

5.1.4 UPnP Setting

If you enable UPNP, once the IP camera is connected into the LAN, it will communicate
with the router in the LAN to do the port-forwarding automatically.

Below Figure 16, tick “Using UPNP to Map Port” and the setting are completed. You
could check the UPNP succeeds or not in the interface of System Maintenance.

Figure 16
Before using UPNP function, please make sure the router’s UPNP function has been
triggered. Not all the routers support UPNP perfectly. Please test if the router works well

13
http://www.wansview.com
with the equipment, if not, we would suggest you to disable this function and do the
port-forwarding manually.

5.1.5 DDNS Setting

Please refer to the content in 4.3.

5.1.6 MSN Setting

Figure 17
User needs to apply for a MSN account for this device first, for example:
[email protected]. Please put this MSN account and its password as above Figure 17.
Then put your MSN account, for example: [email protected], into the ‘MSN Friends
List. Then on your [email protected] MSN list, you can see [email protected] is
online. You just send “url?” to [email protected] and you will get the WAN ip address of
this ip camera. But please make sure [email protected] and [email protected]
should be MSN friends before you do the settings.

5.2 Alarm Settings

5.2.1 Alarm Setting
1） Alarm Detect
User can select the motion detection. If there is any motion, it will detect the motion and
trigger the alarm. In the motion detect sensibility, the larger the figure, the more
sensitive.

As showed in Figure 18, if any external alarm detector is connected, user will be able to
tick “Alarm Input Armed”. If the external alarm detector is an always on switch alarm,
please choose “open”. If the external alarm detector is always off switch alarm, please
choose “close”.

14
http://www.wansview.com

Figure 18

2） Alarm Action
All kinds of alarm modes:-
a) IO interface for alarm signal output: when relay is switched on, the external
alarm will begin to alarm.
b) Send alarm info by email.
c) Send the site pictures to the FTP server, user can also set the break time
between two pictures.
d) Send alarm info to the alarm server.

3） Scheduler
Device will trigger alarm in scheduled time. User can set schedule time to be “all the
time”. Before you set “Schedule”, please go to Date and Time settings to set the correct
time for the item, as shown in figure 19.

15
http://www.wansview.com

Figure 19

5.2.2 Mail Service Setting

Figure 20

16
http://www.wansview.com
The device will send alarm email to you. You only need to fill out the blanks with your
email address as shown in Figure 20. After the setting, please click save and test to
check if it works properly. If it is properly set, user can tick to enable “Report Internet IP
by mail”. After every restart, the device will send its Internet IP address to user’s email
address.

5.2.3 FTP Service Setting

Figure 21
When alarming, device will snap and send the image to FTP server, please make sure
the FTP setting is correct. Above Figure 21 of FTP setting for your reference, after the
setting is finished, click “Test” to test your settings are correct or not.

After correct setting FTP server, you can use “upload Image Periodically” function. Even
no alarm, device can also send the snap image to FTP periodically.

In order to use FTP function, user should apply username and password on the FTP
server first. And please apply some storage, and the authority to write and create
sub-category into it.

5.2.4 Alarm Server

Figure 22
Please confirm if you have connected to alarm server. The alarm message format as
follow:
GET /api/alarm.asp？
username=username&

17
http://www.wansview.com
userpwd=password&
rea=alarm type (1=Motion Detection, 2 =Alarm from Alarm in port)&
io=0
Alarm server needs developing by user. User can extend other functions on this server,
like SMS, MMS alarm, and mobile phone etc.

5.3 Advanced
5.3.1 User Setting
There are three levels of authority; they are Administrator/Operator/Visitor. Administrator
have the highest authority, it can do any change to the settings. Operator account only
can operate the IP camera, can’t do changes to the settings. Visitor account only can
watch the video, can’t do any operation to the IP camera. By default, the
administrator’s user name is admin, password: 123456.

Figure 23

5.3.2 Multi Device Setting

18
http://www.wansview.com
Figure 24
As Figure 24, User can maximum add 9 devices to view the device simultaneously. Click
refresh button to check the device in the LAN. When click the device, will popup setting
dialogue box and input the device info, as figure 25 and click save. After that, must click
submit button to save.

Figure 25

5.3.3 Other settings

Figure 26
Note： the settings for the status light and pan/tilt are not suitable for this item

5.4 Maintain
5.4.1 Device Information

Figure 27

19
http://www.wansview.com
5.4.2 Time Setting
If the device is connected to the Internet, you enable the NTP server to correct the time
and select the right time zone. Or you should use the PC’s time to correct its time.

Figure 28

5.4.3 Firmware upgrade

The device runs 2 kinds of programmer, one is system firmware, the other is application
firmware. They could be upgraded separately.

Figure 29

5.4.4 Restore Factory Default

Click “Restore Factory Default”, it will pop up a dialogue to confirm if you really want to
restore the factory default. After confirmation, the system will restore the factory default
and reboot.

5.4.5 User browsing Log

After enter the log interface, you could view who and when the device is visited.

Figure 30

20
http://www.wansview.com

6 Centralization Control

Figure 31
IPCMonitor is a free software offered by factory, several devices on LAN and WAN can
be browsed at the same time. The software also supports snap, video record, alarm and
so on. The below Figure 31 is the interface.

For more information, pls. refer to the <<IPCMonitor User Manual>> in CD.

7 FAQ
1) Unmatched power adapter will damage the equipment or power adapter

When plug in the power adapter, please check carefully the voltage, it should be 5V
adapter for this equipment.

2) Slowly browse speed

This equipment adopts MJEPG compression format, it needs large network bandwidth,
the narrow bandwidth will affect the browse speed. The typical bandwidth uses situation
as below:
640x480@10fps : 4.0 Megabits ～ 5.0 Megabits
320x240@30fps : 1.2 Megabits ～ 1.6 Megabits

3) Color difference

The default is infrared lens, when visit outdoor or strong infrared light scenes, there are
color differences, the color is not accordance to the real scenes. User can change it to
color lens to solve this problem, but color lens can only use under the daylight situation.

21
http://www.wansview.com

4) Can’t find equipment via search software after connect to LAN

Make sure the equipment and PC is in the same LAN; if install firewall software, please
close it and try again.

5) Can find equipment via search software, but can’t visit

If the IP address of IP camera and PC is not in the same Network Segment, you should
change them on the same Network Segment before visit. Network Segment is the first
three number of IP address. If the IP address of PC is 192.168.0.100, so it can only visit
the equipment which IP address is between 192.168.0.1~192.168.0.255.

6) Can visit via public IP address, but can’t visit via manufacturer’s domain name

Make sure the DNS setting is same as your PC, as below Figure 33, in the search tool,
the DNS 1 and DNS 2 on both side should be same.

Figure 32

22