Mitsubishi Electric Industrial Robots

CRn-500 series
CRn-700 series
RT ToolBox2 / RT ToolBox2 mini
User's Manual
(3D-11C-WINE/3D-12C-WINE)

BFP-A8618
 Safety Precautions
Before using the robot, always carefully read the
precautions below and the separate "Safety Manual" and
take all necessary safety measures.

A. These show precautions based on Labor Health and Safety Regulations (Articles 36, 104, 150,
151).

For the sake of safety, teaching work should only be performed by workers who have
Caution received special education.
(The same is true for any maintenance work done with the power source not cut off.)
→Implementation of safety education

For teaching work, prepare work regulations concerning robot operation methods
Caution and procedures, measures for when there is an abnormality and when restarting, etc.
Perform teaching work according to these regulations.
(The same is true for any maintenance work done with the power source not cut off.)
→Prepare work regulations.

For teaching work, set up a device that can stop operation immediately.
Warning (The same is true for any maintenance work done with the power source not cut off.)
→Emergency stop switch setting

During teaching work, label the start switch etc. to indicate that teaching work is
Caution underway.
(The same is true for any maintenance work done with the power source not cut off.)
→Display that teaching work is underway

Danger During operation, set up a fence or barrier to prevent contact between workers and
the robot.
→ Setting up a safety fence

Determine a uniform signal to relevant staff for the start of operation and use that
Caution signal.
→ Signal for the start of operation

For maintenance work, in principle, cut off the power and label the start switch etc. to
Caution indicate that maintenance work is underway.
→Display that maintenance work is underway

Before starting work, check the robot, emergency stop switches, related devices, etc.
Caution and make sure there are no abnormalities.
→ Check before the start of work
B. This shows precaution points given in the separate "Safety Manual".
For details, please read the text of the "Safety Manual".

Use the robot in an environment that is within the range of its specifications. Failure
Caution to do this can cause a drop in reliability and breakdown.
(Temperature, humidity, atmosphere, noise, etc.)

When transporting the robot, put it into its specified transport posture.
Caution Failure to do this can cause a drop in reliability and breakdown.

Install the robot on a solid platform.

Caution If the robot is in an unstable posture, this can cause positional deviation and
vibration.

As much as possible, wire cables away from noise sources.

Caution If cables are brought too close to noise sources, this can cause positional deviation
and malfunction.

Do not apply excess force to a connector or bend a cable excessively.

Caution Doing so can cause a contact defect or cut line.

Set work masses, including hands, so that they do not excess rated load or permitted
Caution torque.
Exceeding either of these can cause an alarm or breakdown.

Install hands and tools and hold work securely.

Warning Failure to do this can cause objects to fly loose during operation and cause personnel
injury or damage.

Ground the robot and controller reliably.

Warning Failure to do this can cause malfunction due to noise or in an extreme case, electrical
shock.

Display the operating state while the robot is operating.

Caution Lack of such a display can result in someone coming too close to the robot by mistake
or mistaken operation.

Always secure the priority right for control of the robot before doing any teaching work
Warning within the robot's operating range. Failure to do this can allow the robot to start upon
instruction from the outside and cause personnel injury or damage.

Make the jog speed as slow as possible and do not take your eyes off the robot.
Caution Failure to do this may cause a collision between a work piece and peripheral devices.

After completing program editing but before starting automatic operation, always
Caution check operations with step operation. Failure to do this may cause a collision with a
peripheral device due to a programming mistake or the like.

Set up the safety fence in such a way that, while the equipment is running on
Caution automatic, either the safety fence door is locked or if anyone tries to open the door,
the robot is stopped. Failure to take these protective measures can cause an accident
resulting in injury.
 Never on your own judgment make an alterations or use maintenance parts other than
Caution those designated. Doing so can cause breakdown and problems.

When moving the robot arm from the outside, never stick a hand or finger into an
Warning opening. Depending on the posture, the hand or finger could get caught in the
equipment.

Do not switch the robot Off or make an emergency stop of the robot by switching Off
Caution the robot controller's main power supply.
If the robot controller's main power supply is switched Off during automatic operation,
this can reduce the robot's precision. It could also cause the arm to fall or allow inertia
to result in collisions with peripheral device or the like.

When rewriting a program, parameters, or other internal information within the robot's
Caution controller, do not switch Off the robot controller's main power supply.
If the robot controller's main power supply is switched Off during automatic operation
or while a program or parameter is being rewritten, there is a danger of the internal
information in the robot controller being destroyed.

For using RH-5AH/10AH/15AH series or RH-6SH/12SH/18SH series.

Caution While pressing the brake releasing switch on the robot arm, beware of the arm which
may drop with its own weight.
Dropping of the hand could lead to a collision with the peripheral equipment or catch
the hands or fingers.
User's Manual Revision History
Printing Date Manual No. Revision Contents
2008/04 BFP-A8618-* First edition (Corresponds to the Ver.1.1)
Software Revision History
Version Release Date Revision Contents
1.0 2008/01 Initial release (Japanese version only)
1.1 2008/04 CRnQ Communications Added the GOT transparent function.
Parameter editing Added the Multiple CPU setting screen.
 PREFACE
Thank you for purchasing this MELFA Mitsubishi Electric industrial robot.
This document is the user's manual for the MELSOFT "RT ToolBox2" and "RT ToolBox2 mini".
This document will help you to use the functions of this software to the maximum over a wide range of
stages, from initial robot start to program writing, editing, and management.
In order to operate the robot safely, carefully read this document and the safety manual that comes with the
robot main unit before operating the robot. Also, store this manual carefully so that you can take it out and
read it whenever needed.

Target versions for this document

This document is for the MELSOFT "RT ToolBox2" and "RT ToolBox2 mini" Ver. 1.1 and supports the
following robot controllers.
・ CRn-500 series controllers
・ CRnQ-700 series controllers
・ CRnD-700 series controllers
In some locations, this document writes about the "CRn-700 series".

Target readers for this document

This document assumes that the reader understands basic Microsoft Windows operation methods and the
robot controller.
Those who have not mastered basic computer operation methods should read the user's manual for their
computer.

Notation method in this document

This indicates an item for which incorrect handling could present imminent danger
Danger of death or injury.
This indicates an item for which incorrect handling could present a danger of
Warning death or injury.
This indicates an item for which incorrect handling could present a danger of
Caution impairment. It could also present a danger of just physical damage.

This document uses the following general terms and abbreviations

General Contents
Term/Abbreviation
RT ToolBox2 General name for the RT ToolBox2 and RT ToolBox2 mini
To distinguish them in explanations, these two are called the "standard
edition" and "mini edition".
Universal model QCPU General term for Mitsubishi PLC CPU modules of Q02UCPU,
Q03UDCPU, Q04UDHCPU and Q06UDHCPU.
GX Developer Abbreviation of SW D5C-GPPW-E(-EV) / SW D5F-GPPW-E type of
Mitsubishi PLC programming software package.

The Microsoft® Windows® operating system is a registered trademark of the Microsoft Corp. of the United States in the United States
and other countries.
Adobe® and Acrobat® are registered trademarks of Adobe Systems Incorporated.

The system names, product names, etc. in this manual are generally trademarks and registered trademarks of their respective
TM
companies. In the main text, the ©, ®, and marks are omitted.

Transfer of all or part of the contents of this document without permission is prohibited.
The contents of this document are subject to change without notice.
Every effort has been made to ensure the accuracy of the contents of this document, but if you should notice any unclear point, mistake,
or omission, please notify Mitsubishi Electric.

Copyright(C)2008 MITSUBISHI ELECTRIC CORPORATION

 Contents
1. Usage 1-15
1.1. How to Use this Document ......................................................................................................... 1-15
1.2. Checking the Product.................................................................................................................. 1-15
1.2.1. Checking the package ......................................................................................................... 1-15
1.2.2. Checking the CD-ROM contents ......................................................................................... 1-15
1.2.3. About the "MelfaRXM.ocx" communications middleware ................................................... 1-15
1.3. Items to be prepared by the customer ........................................................................................ 1-16
1.3.1. Computer system ................................................................................................................ 1-16
1.3.2. Computer cable ................................................................................................................... 1-16
1.4. Operating Environment ............................................................................................................... 1-17
1.4.1. Connectable robot controllers ............................................................................................. 1-17
1.4.2. Computer system ................................................................................................................ 1-18
1.5. Installation, Uninstallation ........................................................................................................... 1-19
1.5.1. Installation ........................................................................................................................... 1-19
1.5.2. Uninstall ............................................................................................................................... 1-22
1.5.3. USB driver (CRnD-700 series robot controller) installation................................................. 1-23
1.5.4. CRnQ communications USB driver installation ................................................................... 1-25
1.5.5. CRnQ Communications USB driver for GOT transparent installation................................. 1-30
1.6. When Starting at the Same Time as Another Product ................................................................ 1-32

2. RT ToolBox2 Usage 2-33

2.1. Starting RT ToolBox2................................................................................................................... 2-33
2.2. Explanation of RT ToolBox2 Screens.......................................................................................... 2-34
2.3. Communications Server 2........................................................................................................... 2-38
2.4. Closing RT ToolBox2................................................................................................................... 2-39

3. Basic Functions 3-40

4. Workspaces and Projects 4-41

4.1. Workspaces and Projects ........................................................................................................... 4-41
4.2. Creating a New Workspace ........................................................................................................ 4-43
4.3. Opening an Existing Workspace ................................................................................................. 4-44
4.4. Closing a Workspace .................................................................................................................. 4-44
4.5. Deleting a Workspace ................................................................................................................. 4-45
4.6. Saving a Workspace ................................................................................................................... 4-45
4.7. Changing a Workspace Name .................................................................................................... 4-46
4.8. Changing a Workspace Title ....................................................................................................... 4-46
4.9. Adding a Project.......................................................................................................................... 4-47
4.10. Changing a Project Name........................................................................................................... 4-48
4.11. Deleting a Project........................................................................................................................ 4-48
4.12. Contents of Project Tree ............................................................................................................. 4-49
4.13. Copying Programs Between Projects ......................................................................................... 4-49
4.14. Offline/Online/Simulation............................................................................................................. 4-50

5. Connecting with the Robot 5-52

5.1. Robots Connected and Types of Communication....................................................................... 5-52
5.2. Connection Settings .................................................................................................................... 5-53
5.2.1. USB Communication Settings ............................................................................................. 5-54
5.2.2. TCP/IP (Ethernet) Communication Settings........................................................................ 5-54
5.2.3. RS-232 Communication Settings ........................................................................................ 5-55
5.2.4. CRnQ Communications Settings......................................................................................... 5-56
6. Robot Program Language Setting 6-63

7. Writing Programs 7-64

7.1. Writing a New Program ...............................................................................................................7-64
7.1.1. Writing a new program on the computer..............................................................................7-64
7.1.2. Writing a new program in the robot controller......................................................................7-65
7.2. Opening an Existing Program .....................................................................................................7-66
7.2.1. Opening an existing program on the computer ...................................................................7-66
7.2.2. Opening a program in a robot controller ..............................................................................7-66
7.2.3. Read Items when opening program in robot controller........................................................7-67
7.3. Explanation of Program Edit screen............................................................................................7-68
7.4. Program Editing Menu Bar ..........................................................................................................7-69
7.5. Customizing the Program Edit Screen ........................................................................................7-71
7.5.1. Changing the display area ...................................................................................................7-71
7.5.2. Command format hints.........................................................................................................7-72
7.5.3. Character colors...................................................................................................................7-72
7.5.4. Changing the font.................................................................................................................7-73
7.6. Program Editing...........................................................................................................................7-74
7.6.1. MELFA-BASIC V command statement editing ....................................................................7-74
7.6.2. MELFA-BASIC IV and Movemaster command command statement editing ......................7-75
7.6.3. Position variable editing .......................................................................................................7-76
7.6.4. Edit assist functions .............................................................................................................7-78
7.7. Saving Programs .........................................................................................................................7-85
7.7.1. Save .....................................................................................................................................7-85
7.7.2. Saving on computer .............................................................................................................7-86
7.7.3. Saving in robot controller .....................................................................................................7-87
7.7.4. Items written when saving in robot ......................................................................................7-88
7.7.5. Setting the syntax check for before program saving ...........................................................7-89
7.8. Program Printing..........................................................................................................................7-90
7.8.1. Checking a print image ........................................................................................................7-90
7.8.2. Printing a program ...............................................................................................................7-90
7.8.3. Setting to print a program ....................................................................................................7-90
7.9. Program Debugging ....................................................................................................................7-91
7.9.1. Starting debugging ...............................................................................................................7-91
7.9.2. Executing programs step by step ........................................................................................7-92
7.9.3. Revising programs ...............................................................................................................7-93
7.9.4. Setting and deleting breakpoints .........................................................................................7-94
7.9.5. Ending debugging ................................................................................................................7-95
7.10. Program Management.................................................................................................................7-96
7.10.1. Program list display..............................................................................................................7-97
7.10.2. Copy.....................................................................................................................................7-97
7.10.3. Move ....................................................................................................................................7-98
7.10.4. Delete...................................................................................................................................7-98
7.10.5. Rename ...............................................................................................................................7-98
7.10.6. Protect settings ....................................................................................................................7-99
7.10.7. Comparison..........................................................................................................................7-99
7.11. Program Conversion..................................................................................................................7-100
7.11.1. Starting program conversion ..............................................................................................7-100
7.11.2. Line number conversion (from MELFA-BASIC IV to MELFA-BASIC V) ............................7-101
7.11.3. Position data conversion (from E/EN/M1/M2 series to CRn-500/700 series)....................7-103

8. Setting Parameters 8-105

8.1. Editing from parameter list.........................................................................................................8-105
8.1.1. Starting ...............................................................................................................................8-105
8.1.2. Parameter editing...............................................................................................................8-107
8.1.3. Parameter list reading........................................................................................................8-108
8.1.4. Finding parameters ............................................................................................................8-108
8.2. Robot Controller Operation Modes for Parameter Writing ........................................................8-109
8.3. Operating Range Parameters ................................................................................................... 8-110
8.4. Jog Parameters ......................................................................................................................... 8-110
8.5. Hand Parameters ...................................................................................................................... 8-111
8.6. Weight and Size Parameters..................................................................................................... 8-112
 8.7. Tool Parameters .........................................................................................................................8-113
8.8. Slot Tables..................................................................................................................................8-114
8.9. Output Signal Reset Pattern Parameters...................................................................................8-115
8.10. Assigning Dedicated Input/Output Signals ................................................................................8-116
8.10.1. General 1 Parameters ........................................................................................................8-116
8.10.2. General 2 parameters.........................................................................................................8-116
8.10.3. Data parameters.................................................................................................................8-117
8.10.4. Jog parameters...................................................................................................................8-117
8.10.5. Hand parameters................................................................................................................8-118
8.10.6. Warm-up operation parameters..........................................................................................8-118
8.10.7. Slot start (each slots) parameters.......................................................................................8-119
8.10.8. Slot stop (each slots) parameters.......................................................................................8-119
8.10.9. Servo On/Off (each robot) parameter................................................................................ 8-120
8.10.10. Machine lock (each robot) parameters.............................................................................. 8-120
8.11. RS-232 Setup Parameters........................................................................................................ 8-121
8.12. Zone Parameters ...................................................................................................................... 8-121
8.13. Free Plane Limit Parameters .................................................................................................... 8-122
8.14. Escape Point Parameters ......................................................................................................... 8-122
8.15. Robot Program Language Parameters ..................................................................................... 8-123
8.16. Additional Axis Parameters ....................................................................................................... 8-124
8.17. Collision Detection Parameters................................................................................................. 8-125
8.18. Warm-Up Operation Parameters .............................................................................................. 8-126
8.19. Movement Parameters.............................................................................................................. 8-127
8.20. Program Parameters................................................................................................................. 8-128
8.21. User Error Parameters .............................................................................................................. 8-129
8.22. Ethernet Settings....................................................................................................................... 8-130
8.23. Multiple CPU Settings ............................................................................................................... 8-131
8.24. Parameter printing..................................................................................................................... 8-132

9. Status Monitoring 9-133

9.1. Robot Operation Monitoring...................................................................................................... 9-134
9.1.1. Slot operation statusmonitaring ......................................................................................... 9-134
9.1.2. Program monitoring ........................................................................................................... 9-135
9.1.3. Movement status ............................................................................................................... 9-138
9.1.4. Errors................................................................................................................................. 9-139
9.1.5. Robot status ...................................................................................................................... 9-141
9.2. Signal Monitoring ...................................................................................................................... 9-142
9.2.1. General signal ................................................................................................................... 9-142
9.2.2. Named signals................................................................................................................... 9-145
9.2.3. Stop signal ......................................................................................................................... 9-147
9.2.4. Register (CC-Link) monitoring........................................................................................... 9-148
9.3. Production Condition Monitoring............................................................................................... 9-151
9.3.1. Operation hours................................................................................................................. 9-151
9.3.2. Production information....................................................................................................... 9-151

10. Maintenance 10-152

10.1. Setting Origin Data.................................................................................................................. 10-152
10.1.1. Origin data input technique ............................................................................................. 10-154
10.1.2. Mechanical stopper technique......................................................................................... 10-155
10.1.3. Tool technique ................................................................................................................. 10-155
10.1.4. ABS origin technique ....................................................................................................... 10-156
10.1.5. User Origin Technique ..................................................................................................... 10-156
10.1.6. Origin Parameter Backup ................................................................................................ 10-157
10.2. Initialization ............................................................................................................................. 10-158
10.2.1. Starting ............................................................................................................................ 10-158
10.2.2. Setting the time in the robot controller............................................................................. 10-158
10.2.3. Deletion of all robot programs ......................................................................................... 10-159
10.2.4. Initializing the battery remaining time .............................................................................. 10-159
10.2.5. Serial number .................................................................................................................. 10-159
10.3. Maintenance Forecasting........................................................................................................ 10-160
10.3.1. Specifications................................................................................................................... 10-160
10.3.2. Starting ............................................................................................................................ 10-160
 10.3.3. Forecasting ......................................................................................................................10-161
10.3.4. Settings ............................................................................................................................10-162
10.3.5. Reset screen....................................................................................................................10-164
10.3.6. Resetting maintenance forecast information with teaching box ......................................10-166
10.3.7. Others ..............................................................................................................................10-167
10.4. Position repair Function...........................................................................................................10-168
10.4.1. Specifications ...................................................................................................................10-168
10.4.2. Starting .............................................................................................................................10-169
10.4.3. Flow of operations............................................................................................................10-170
10.4.4. Introduction ......................................................................................................................10-171
10.4.5. Communications settings.................................................................................................10-171
10.4.6. Robot selection and parameter backup ...........................................................................10-172
10.4.7. Revision parameter generation procedure selection .......................................................10-173
10.4.8. Program selection ............................................................................................................10-174
10.4.9. Program reading and backing up.....................................................................................10-175
10.4.10. Tool setting check ............................................................................................................10-176
10.4.11. Revision parameter selection ..........................................................................................10-177
10.4.12. Reteaching work ..............................................................................................................10-183
10.4.13. Writing parameters...........................................................................................................10-186
10.4.14. Controller power supply Off, On ......................................................................................10-187
10.4.15. Exit ...................................................................................................................................10-188
10.4.16. Revision parameter editing ..............................................................................................10-189
10.5. Servo Monitor ..........................................................................................................................10-190
10.5.1. Load .................................................................................................................................10-190

11. Option Card 11-191

12. Backup and Restore 12-192

12.1. Backup(Robot -> PC) ..............................................................................................................12-193
12.2. Restore (PC -> Robot).............................................................................................................12-195
12.3. Deleting Backup Data..............................................................................................................12-197

13. Simulation 13-198

13.1. Starting a Simulation................................................................................................................13-199
13.2. Explanation of the Simulation Operation Screen ....................................................................13-200
13.3. Robot View Start......................................................................................................................13-201
13.4. Robot Program Selection ........................................................................................................13-202
13.5. Program Execution ..................................................................................................................13-203
13.6. Specifying the Starting Line for Program Execution ................................................................13-203
13.7. Breakpoint Setting ...................................................................................................................13-204
13.8. Step Operation.........................................................................................................................13-204
13.9. Direct Execution ......................................................................................................................13-205
13.10. Jog Operation ..........................................................................................................................13-206
13.11. Simulation Robot Position Variable Editing .............................................................................13-207
13.12. Tact Time Calculation ..............................................................................................................13-208
13.12.1. Conditions for tact time measurement .............................................................................13-209
13.12.2. Tact time measurement....................................................................................................13-210
13.12.3. Causes of tact time deviation...........................................................................................13-212
13.13. Ending Simulation....................................................................................................................13-213

14. MelfaRXM.ocx Communications Middleware Setup 14-214

14.1. Summary .................................................................................................................................14-214
14.2. CD-ROM Contents ..................................................................................................................14-214
14.3. User's Manual Reading Guide.................................................................................................14-215
14.4. Installation................................................................................................................................14-215

15. Appendix 15-217

15.1. Q&A .........................................................................................................................................15-217
15.2. Index ........................................................................................................................................15-227
1. Usage
This explains precautions you need to know before using this software.

1.1. How to Use this Document

The manual is in the CR-ROM as the Adobe PDF file.
D:/Doc/BFP-A8618.pdf (Example for the CD-ROM drive is “D:”.)

For reading the manual, Adobe Acrobat Reader Ver.5.0 or more is required.
If Adobe Acrobat Reader isn’t installed, please download from following Adobe Systems Incorporated URL (As
of December, 2007)
URL: http://www.adobe.com/

1.2. Checking the Product

1.2.1. Checking the package
Please check if all items shown below are included in the package.
- CD-ROM "RT ToolBox2"
- Setup Guide
- END-USER SOFTWARE LICENSE AGREEMENT
- License Certification
(Please make sure Product ID is printed on it.)
* Please contact the branch office or the agency if there is some shortage in the package.

1.2.2. Checking the CD-ROM contents

The CD-Rom has the following configuration.
/:

: The files for installagion of this software

:

Doc ・・・・・・・ This manual (pdf)

Misc ・・・・・・・ User Registation Application Form (fax, postcard) is stored

Utility ・・・・・・・ The folder for setup of the communication middleware "MelfaRXM.ocx"

1.2.3. About the "MelfaRXM.ocx" communications middleware

MelfaRXM.ocx is the ActiveX control that communicates to robot-controller. You can create the Windows
Application of "MELFA ROBOT" by using this control.
You can use "MelfaRXM.ocx" in only standard version of this software.
For information on how to set up "MelfaRXM.ocx", refer to "14 MelfaRXM.ocx Communications
Middleware Setup".
In case of using only the function of “RT ToolBox2”, you don't need to install this software.

1-15 1-15
1.3. Items to be prepared by the customer
This explains what the customer needs to prepare in order to use this software

1.3.1. Computer system

Use a computer that meets the specifications given in: "1.4 Operating Environment".

1.3.2. Computer cable

Prepare the cable for connecting the controller and the computer. The cable required depends on the
connection specifications and controller used, as shown below.
For the RS-232 cable refer to the "Standard Specifications" for your robot.

Table 1-1 CRｎD-700 Series, CRn-500 Series Communication Cables

Method Description Model name Manufacturer
USB USB A type, USB mini B type - -
Ethernet 10BASE-T, 100BASE-TX - -
CRnD-700
2D-232CBL03M Mitsubishi Electric
series
RS-MAXY-CBL
For controller front panel
RS-232 CRn-500 RS-AT-RCBL
Mitsubishi Electric
series (for expansion serial
interface (option))
For expansion option box (CR1-EB3) RS-AT-RCBL Mitsubishi Electric

Table 1-2 CRnQ-700 Series Communication Cables

Cables confirmed by Mitsubishi Electric to operate
Method Description properly
Model name Manufacturer
ZUM-430 Loas Co.
USB-M53 Elecom Co.
USB USB A type to mini B type Mitsubishi Electric System
GT09-C20USB-5P
Service
MR-J3USBCBL3M Mitsubishi Electric
Ethernet 10BASE-T, 100BASE-TX
For connecting by personal computer -
PLC CPU
RS-232 QC30R2 Mitsubishi Electric
(when Personal computer connector is
D-sub, 9-pin)

1-16 1-16
1.4. Operating Environment
This explains the operating environment.

1.4.1. Connectable robot controllers

This software can be connected with the robot controllers shown below

Table 1-3 Connectable Robot Controllers and Communications Types

Robot controller Communications (*1) Remark
CrnD-700 series
USB (*2)

Ethernet (TCP/IP)

RS-232

CrnQ-700 series
USB (*2)

CRnQ Ethernet The PLC Ethernet interface module is

communications (TCP/IP) required.

RS-232

CRn-500 series
The robot controller must have the
Ethernet (TCP/IP)
"Ethernet interface" option.

RS-232

(*1) The computer must have each ports for communications.

(*2) When using USB connection, 1 computer can connect to only 1 robot controller.

This software can be connected to a maximum of 32 controllers at the same time. These controllers may be
different models.

1-17 1-17
1.4.2. Computer system

This software operates on PC/AT compatible computers that meet the following specifications.

Item Recommended environment

CPU Pentium Ⅲ 1 GHz or higher
Main memory 512 MB min.
Hard disk Available capacity 300 MB min.
Display XGA (1024x768) or higher
Optical device CD-ROM drive
Keyboard PC/AT compatible keyboard
Pointing device Must operate on Windows
- USB2.0
(Caution: This cannot be used for connection with the CRn-500 series
Communications controller.)
functions - LAN: 100Base-TX/10Base-T
Communications port - RS-232 communications port that operates on Windows (Minimum
9600bps: 1 port)
Must have one of the above interfaces
Windows 2000 Professional
Windows XP Professional (*1)
Windows XP Home Edition (*1)
OSs for which Windows Vista Ultimate (*1)
operation is warranted Windows Vista Business (*1)
Windows Vista Home Premium (*1)
Windows Vista Home Basic (*1)
English versions for each edition
*1: Only supports 32-bit versions

1-18 1-18
1.5. Installation, Uninstallation
This section explains the method for installing the software and the method for uninstalling it.

Caution
Uninstall the old version before installing the new one.
If an old version of "RT ToolBox2" is installed, uninstall the old version of "RT ToolBox2", then install
the new version of "RT ToolBox2".

1.5.1. Installation

Caution
When installing, log in as a user with administrator authority.
When installing, log in as a user with administrator authority. The system will not let you install if you
log in as a user who does not have administrator authority.

Install this software with the procedure below.

(1) When you insert this product into the computer's CD-ROM drive, the setup screen is displayed
automatically.

(2) If the setup screen is not displayed when you insert this product into the computer's CD-ROM drive,
display the setup screen with the following method.
- For any OS other than Windows Vista
- In Windows Vista, when using the [Start] menu with the classic display
1) Select [Start] button -> [Run].
2) Check the CD-ROM drive name, then input "drive name":\Setup.exe.
(If the CD-ROM drive is "D:", input "D:\Setup.exe".)

- In Windows Vista, when not using the [Start] menu with the classic display
1) Click [Start] button -> [All Programs] -> [Accessories], then select [Run].
2) Check the CD-ROM drive name, then input "drive name":\Setup.exe.
(If the CD-ROM drive is "D:", input "D:\Setup.exe".)

Figure 1-1 Specify the File Name and Execute

With Windows Vista, when using the classic display, when not using the [Start] menu with the classic
display, you can use the [Start] menu Search box instead of executing the [Run] command.

1-19 1-19
 Start

(a) Set the CD-ROM in PC's CD-ROM drive. (f) Input Product ID

(b) Open "Setup.exe" in CD-ROM.

(when it is not started automatically)

(c) Starting installation Wizard

(d) License Agreement

(e) Input "Customer Information"

(g) Choose Destination Location

(h) Installation Wizard Complete

(i) Start the program, and confirm whether

the product was installed correctly

Finish

* Product ID is printed on the Certificate of License permission

* After the installation is completed, the computer should be likely to be rebooted.

1-20 1-20
 Caution
About the confirmation and warning message displayed during
installation
During installation on Windows XP or Windows Vista, the following confirmation and warning messages are
displayed, but select to continue installation. If you select not to install, please execute the installation again.

(1) Installation confirmation message for USB driver software (for Windows XP)

(2) Installation confirmation message for USB driver software (for Windows Vista)

(3) Installation warning message for USB driver software (for Windows Vista)

<Remark>
We have confirmed operation at our company. No problem occurs after installation.

1-21 1-21
1.5.2. Uninstall

Uninstall with the following method. Start uninstallation.

- For any OS other than Windows Vista

Execute [Start] – [Control Panel] [Program Add and Delete]. From [Start] – [Control Panel], display the
control panel and select "Add/Remove
- Windows Vista Programs".
Open [Start] – [Control Panel].

When not using the classic display Select the product to delete, then click the
With [Control Panel] [Program], execute [Uninstall Program]. "Change or Remove Programs".

For classic display

With [Control Panel] [Program Functions], select the Completion
application name, then execute the uninstallation.

RT ToolBox2 English

Table 1-2 Uninstalling Applications (WindowsXP)

1-22 1-22
1.5.3. USB driver (CRnD-700 series robot controller) installation

Connecting the CRnD-700 series robot controller with USB requires installation of the robot USB driver.
Install with the following procedure.

Caution
If the USB driver cannot be installed, check the following
setting.
<When Windows 2000 is used>
If you have selected "Block-Prevent installation of unsigned files" after [Control Panel] - [System] -
[Hardware] - [Driver Signing], the USB driver may not be installed.
Choose "Ignore-Install all files, regardless of file signature" or "Warn-Display a message before
installing an unsigned file" for [Driver Signing], and install the USB driver.

<When Windows XP is used>

If you have selected "Block-Never install unsigned driver software" after [Control Panel] - [System] -
[Hardware] - [Driver Signing], the USB driver may not be installed.
Choose "Ignore-Install the software anyway and don't ask for my approval" or "Warn-Prompt me each
time to choose an action" for [Driver Signing], and install the USB driver.

1.5.3.1. When using Windows 2000

When you connect the CRnD-700 robot controller and the computer with a USB cable, installation starts
and completes automatically.

1.5.3.2. When Using Windows XP

Below is the installation procedure for the USB driver using Windows XP (Professional).
1) When you connect the computer and
CRnD-700 series robot controller with
a USB cable, the screen on the left is
displayed. Select "Install the software
automatically (Recommended)", then
click the [Next] button. Installation of
the USB driver starts.

1-23 1-23
 2) When the screen on the left is
displayed, the installation is complete.
Click the [Finish] button to end the
installation.

↓
(Completed)

1.5.3.3. When using Windows Vista

When you connect the CRnD-700 robot controller and the computer with a USB cable, installation starts
and completes automatically.

1-24 1-24
1.5.4. CRnQ communications USB driver installation

Connecting the CRnQ-700 series robot controller with USB requires installation of the robot USB driver.
Install with the following procedure.

Caution
If the USB driver cannot be installed, check the following
setting.
<When Windows 2000 is used>
If you have selected "Block-Prevent installation of unsigned files" after [Control Panel] - [System] -
[Hardware] - [Driver Signing], the USB driver may not be installed.
Choose "Ignore-Install all files, regardless of file signature" or "Warn-Display a message before
installing an unsigned file" for [Driver Signing], and install the USB driver.

<When Windows XP is used>

If you have selected "Block-Never install unsigned driver software" after [Control Panel] - [System] -
[Hardware] - [Driver Signing], the USB driver may not be installed.
Choose "Ignore-Install the software anyway and don't ask for my approval" or "Warn-Prompt me each
time to choose an action" for [Driver Signing], and install the USB driver.

1.5.4.1. When using Windows 2000

The following indicates the procedure for installing the USB driver when using Windows 2000.
1) The screen shown on the left appears
when you connect the personal
computer and Universal model QCPU
by the USB cable.
Click the [Next] button.

↓
2) Choose "Search for a suitable driver
for my device [recommended]" and
click the [Next] button.

1-25 1-25
 3) Check "Specify a location" and click
the [Next] button.

↓
4) As the left screen appears, set the
“C:\Melsec\EasySocket\USBDrivers”
and click the [Next] button.
If volume MELSOFT products have
been installed, browse the installation
destination “EasySocket\USBDrivers”
of the first product.

↓
5) The screen on the left appears to
indicate completion of installation.
Click the [Finish] button to terminate
installation.

↓
(Completed)

1-26 1-26
1.5.4.2. When using Windows XP
The following indicates the procedure for installing the USB driver when using Windows XP
(Professional).
1) The screen shown on the left appears
when you connect the personal
computer and Universal model QCPU
by the USB cable.
Choose "Yes, now and every time I
connect a device" and click the [Next]
button.

↓
2) As the screen on the left appears,
choose "Install from a list or specific
location [Advanced]" and click the
[Next] button.

↓
3) As the screen on the left appears,
choose "Search for the best driver in
these locations".
Check "Include this location in the
search" and set the
“C:\Melsec\EasySocket\USBDrivers”.
After setting, click the [Next] button.
If volume MELSOFT products have
been installed, browse the installation
destination "EasySocket\USBDrivers"
of the first product.

1-27 1-27
 4) As the screen on the left appears,
click the [Continue Anyway] button to
continue the installation of the USB
driver.
(No problem will occur after
installation of the USB driver.)

↓
5) The screen on the left appears to
indicate completion of installation.
Click the [Finish] button to terminate
installation.

↓
(Completed)

1.5.4.3. When using Windows Vista

The following indicates the procedure for installing the USB driver when using Windows Vista (Business).
1) The screen shown on the left appears
when you connect the personal
computer and Universal model QCPU
by the USB cable.
Select "Locate and install driver
software (recommended)" and wait for
the search to end.

1-28 1-28
 2) The screen on the left is displayed, so
select "Browse my computer for driver
software (advanced)".

↓
3) The screen on the left is displayed,
so select
“C:\Melsec\EasySocket\USBDrivers”.
After making the setting, click the
[Next] button.
When multiple MELSOFT products
are installed, set the default product
installation folder
“EasySocket\USBdrivers”.

↓
4) The screen on the left is displayed, so
select "Install this driver software
anyway".

↓
5) The screen on the left is displayed.
Click the "Close" button. This
completes the installation.

↓
(Completed)

1-29 1-29
1.5.5. CRnQ Communications USB driver for GOT transparent installation

Connecting the CRnQ-700 series robot controller with USB via GOT transparent mode requires installation of
the USB driver for the GOT transparent. Install with the following procedure.
This function is available from RT ToolBox2 Ver.1.1 or later.

Caution
If the USB driver cannot be installed, check the following
setting.
<When Windows 2000 is used>
If you have selected "Block-Prevent installation of unsigned files" after [Control Panel] - [System] -
[Hardware] - [Driver Signing], the USB driver may not be installed.
Choose "Ignore-Install all files, regardless of file signature" or "Warn-Display a message before
installing an unsigned file" for [Driver Signing], and install the USB driver.

<When Windows XP is used>

If you have selected "Block-Never install unsigned driver software" after [Control Panel] - [System] -
[Hardware] - [Driver Signing], the USB driver may not be installed.
Choose "Ignore-Install the software anyway and don't ask for my approval" or "Warn-Prompt me each
time to choose an action" for [Driver Signing], and install the USB driver.

1.5.5.1. When using Windows 2000

When you connect the GOT and the computer by the USB cable, installation starts and completes
automatically.

1.5.5.2. When using Windows XP

The following indicates the procedure for installing the USB driver when using Windows (Professional)
1) The screen shown on the left appears
when you connect the personal
computer and GOT by the USB cable.
Choose "Yes, now and every time I
connect a device" and click the [Next]
button.

1-30 1-30
 2) As the screen on the left appears,
select "Install the software
automatically (Recommended)", then
click the [Next] button.

↓
3) As the screen on the left appears,
click the [Continue Anyway] button to
continue the installation of the USB
driver.
(No problem will occur after
installation of the USB driver.)

↓
4) The screen on the left appears to
indicate completion of installation.
Click the [Finish] button to terminate
installation.

↓
(Completed)

1.5.5.3. When using Windows Vista

When you connect the GOT and the computer by the USB cable, installation starts and completes
automatically.

1-31 1-31
1.6. When Starting at the Same Time as Another Product
When starting this software and another one of our products at the same time, follow the following precaution.
Correct communications and screen display are sometimes not possible.

Table 1-4 Precautions for Starting at the Same Time with Another Product
Product name Explanation Precaution
RT ToolBox Older version of this Can not be used at the same time as
computer support software software this software
Can not be used at the same time as
MELFA-Works 3D robot simulator
this software
Network vision sensor
MELFA-Vision Start this software first.
software
E/EN series computer support Can not be used at the same time as
E/EN series software
software for Windows this software
R-250R/R-300R series Can be used at the same time as this
P/P-2
software software

1-32 1-32
2. RT ToolBox2 Usage
This explains the usage of this software simply.

2.1. Starting RT ToolBox2

When you install this software, a shortcut is prepared on the desktop. Start RT ToolBox2 by double clicking
this short cut.

Figure 2-1 RT ToolBox2 Shortcut

From [Start] button -> [All Programs] -> [MELSOFT Applications], select [RT ToolBox2] and start it.

Figure 2-2 RT ToolBox2 Initial Screen

When you start RT ToolBox2, "Communications Server 2" is started up as an icon.

This Communications Server 2 has functions for connecting with a robot controller or during a simulation, a
virtual controller. Do not close Communications Server 2.

Figure 2-3 Communication Server 2

2-33 2-33
2.2. Explanation of RT ToolBox2 Screens
The composition of the main RT ToolBox2 screen is as follows.

(1) Title bar

(4) Tool bar (2) Menu bar

(7) Screens

(5) Project tree

The screen currently active
is displayed on top.

(7)
(4) Screens
ツールバー

(6) Property window

(8) Status bar

Figure 2-4 Explanation of Main Screen

(1) Title bar

Displays the name of the workspace currently being edited.
Click to close RT ToolBox2.
After the size is changed, you can close RT ToolBox2.
Minimizes RT ToolBox2.

Displays the name of the workspace currently being Maximizes/minimizes RT ToolBox2.

edited.
The status of the connection with the robot is displayed. The
connection statuses are online, offline, and simulation.

2-34 2-34
(2) Menu bar
Displays the names of the menus that can be used in RT ToolBox2.
When a menu is selected, a dropdown menu is displayed from which you can use various functions.

The menu bar display contents and their enabled/disabled status depend on which screen is currently
active.

(3) Dropdown menu

Displays the names of the functions you can use in RT ToolBox2.
When you click a function name, it displays a screen with the settings etc. for the selected function.
When " " is displayed at the right end of a dropdown menu, a dropdown menu for the selected function is
displayed

Displays a
dropdown menu.
Click to display the screen.

(4) Tool bar

Displays buttons for the functions assigned to the menu bar.

The tool bar display depends on which screen is currently active and on the robot connection status.

2-35 2-35
(5) Project tree
Displays a list of all the projects registered in the workspace and by functions.
From this tree, the program edit screen, monitor screen, etc. can be started.

The project tree is a docking window. By dragging the title section with the mouse, you can dock the
project tree at the top, bottom, left, or right edge of the main screen.

When the project tree is closed, you can display it again by clicking on the menu bar [View] -> [Project
Tree].

(6) Property window

You can reference various attributes of the workspace being edited.
If you click an item on the project tree, its attributes are displayed.

The attributes are being displayed

displayed.

The property window is a docking window. By dragging the title section with the mouse, you can dock the
project tree at the top, bottom, left, or right edge of the main screen.

The default setting for the property window is not to be displayed. You can display the property window
with the menu bar [View] -> [Property].

2-36 2-36
(7) Screens
Displays the screens that can be started from the project tree, including the program edit screen and
monitor screen. The currently active screen is displayed on top.

To close a screen click the [ ] at the top right of the screen.

You can also change the screen size with the button at the top right of the screen.

Minimizes the screen. Closes the screen.

Maximizes/minimizes the screen.

(8) Status bar

Displays RT ToolBox2 status information.
The status of the connection with the robot is displayed. Displays the Num
The connection statuses are online, offline, and simulation. Lock status.

During program editing, displays the cursor position. Displays the Caps
Lock status.

(9) Handy menu display

By clicking the right button on the mouse, you can display the right button menu, depending on the work
contents. Using this menu can increase work efficiency.
During program editing, the right button menu includes such functions as [Copy], [Paste], and [Cut].

2-37 2-37
2.3. Communications Server 2
When you start RT ToolBox2, "Communications Server 2" is started up as an icon.
This Communications Server 2 has functions for connecting with a robot controller or during a simulation, a
virtual controller.

Figure 2-5 Communications Server 2 as Icon

Caution
Do not close Communication Server 2 manually.
Communication Server 2 has functions for connecting to a robot controller or during simulation, a
virtual controller. Do not close Communication Server 2. Communication Server 2 closes
automatically when RT ToolBox2 is closed.

Turn Communication Server 2 into an icon.

Turn Communication Server 2 into an icon with the button.

When you return Communications Server 2 from an icon to its original size, you can check the status of the
connection with the robot.

(1) Title bar

(2) Line State

(3) Communication (5) Robot

State Information

(4) Robot
controller
Figure 2-6 Communication Server2

(1) Title bar

(AA/BB) AA: shows the number of robot controllers with which connections are established and BB:
shows the number of projects switched online.

(2) Line State

The connection status of the communication line with the robot is displayed. The status color indicates
the status of the robot controller that is currently being selected.
Table 2-1 Line State
Status Content Color
Connecting Indicates that the connection with the robot has been established. Blue
Indicates that a communication to verify connection is being made in the case
of RS-232 connection.
Connection wait Green
Indicates the wait status for communication port connection in the case of
TCP/IP connection.
Displayed when the data reception enable signal cannot be detected because
a cable has been disconnected or the robot has not been started in the case
Connection
of RS-232 connection. Red
error
Displayed when the communication port cannot be opened in the case of
TCP/IP connection.
Communication Displayed when the communication port cannot be opened in the case of
Red
Setting error RS-232 connection. This is not displayed in the case of TCP/IP connection
Waiting Indicates the idling status displayed at the start of remote maintenance. Yellow

2-38 2-38
(3) Communication State
The contents of communication with the robot controller are displayed.

(4) Robot
This changes the robot controller for which the "Line status" and "Communication status" are displayed.
This is only displayed for robot controllers that are online or have been switched to simulation status.

(5) Robot Information

Information on the currently connected robot can be referenced.

Figure 2-7 Connected Robot Information

Caution
Cautions when connected on USB with CRnQ communications
When connected on USB with CRnQ communications, after connecting normally, if the
communications are cut off due to any of the following external causes, the line status display remains
"Connected". If this happens, return this software offline, remove the cause of the cutoff, and then go
back online.
・ The robot controller power supply went off.
・ The communication cable was disconnected.

2.4. Closing RT ToolBox2

To close RT ToolBox2, on the menu bar, click [Workspace] -> [Close Application]. You can also close with
the [ ] button on the top right of the screen.
When you close RT ToolBox2, Communications Server 2 also closes automatically.

2-39 2-39
3. Basic Functions
The basic functions of this software are shown below.

Table 3-1 RT ToolBox2 Basic Functions

Function Explanation
Offline Targets files on the computer.
Robot model Displays the model of the robot used.
Program Displays the names of the robot programs written on the computer.
Online These are used with the robot controller connected.
Robot model Displays the model of the robot connected to the robot controller.
Program Displays the names of the programs stored on the robot controller.
Parameters
Parameter list The parameters can be set individually.
Parameter The parameters can be set by robot function individually.
settings by The functions are as follows.
function ・ Operating range ・ Free plane limit
・ Jog ・ Evacuation point
・ Hand ・ Robot language
・ Weight and size ・ Added axes
・ Tool ・ Collision detection
・ Slot table ・ Heater operation
・ Output signal reset pattern ・ Operation parameters
・ Dedicated input/output signal ・ Program parameters
allocation ・ User error
・ RS-232 settings ・ Ethernet setting
・ Zone
Monitors
Operation You can reference the slot status, program, monitor, operation status, and
monitor current errors.
Signal monitor You can check the statuses of signals input to the robot and signals output
from the robot.
Work monitor You can check the robot work time and production information for each
robot program.
Maintenance
Home position This sets the robot home position.
data
Initialization This sets the robot controller's internal time, deletes all the programs in
the controller, initializes the battery time remaining, and sets the serial
number for the connected robot.
Maintenance Forecasts the time for maintenance.
forecast
Position repair Supports recovery from home position deviation
Servo monitor Monitors servo system information.
Option card You can check information on option cards mounted in the robot controller.
Simulation This can be used connected with a virtual robot.
*This can only be used with the standard edition.
Same functions as The same functions can be used with a virtual robot controller as with an
online online one.
Tact time measurement The tact time for the robot program with the specified contents can be
measured in the simulation.
Backup, restore You can back up the information in the robot controller and restore backed
up information into the controller.

3-40 3-40
4. Workspaces and Projects
This explains about workspaces and projects.

4.1. Workspaces and Projects

This software has workspaces and projects.
The information for one controller is managed as one project. A workspace can manage up to 32 projects. If
Ethernet is used for communications, you can simultaneously reference information on multiple projects (robot
controllers) registered in the workspace.
When using multiple robot controllers, it is convenient to manage with separate workspaces for each
manufacturing line and installation location.

(1) Using multiple robot controllers (up to 32)

RT ToolBox2
Workspace
You can reference
Project Project Project the information for
1 2 ・・・ 32 multiple controllers
at the same time.

You can connect multiple

Communication Communication Communication controllers at the same time.

...

Figure 4-1 Using Multiple Robot Controllers

(2) Using 1 robot controller

RT ToolBox2
Workspace
Project
1

Communication

Figure 4-2 Using One Robot Controller

Caution
You cannot edit multiple workspaces at the same time.
With this software, you cannot edit multiple workspaces at the same time. Register into a single
workspace all the projects (controllers) you want to reference at the same time.

Simultaneous connection with 32 units

The maximum of 32 robot connections is a theoretical value. It does not guarantee that if you
actually connect 32 robots, you will achieve the same performance as when only 1 robot is connected.
For example, if you monitor all the robots when 32 are connected, status updating is slower than for
when 1 robot is connected.

Workspace editing and storage and project addition etc. are explained from the next section on.

4-41 4-41
 Caution
Update workspaces and projects offline.
In the online status or while a simulation is running, you can not perform the following operations.
Switch offline, then perform the operations.
・ Opening an existing workspace
・ Saving the workspace with a different name
・ Adding a project
・ Changing a project name
・ Deleting a project

For details on switching offline, see "4.14 Offline/Online/Simulation".

4-42 4-42
4.2. Creating a New Workspace
Click [Workspace] -> [New Workspace］ or click (Ctrl + N).

Figure 4-3 Creating a New Workspace

Input the workspace name and title, then click the [OK] button.

Figure 4-4 Screen After New Workspace Created

The project tree is displayed in the workspace and the "RC1" project is created as the default value.
This project name can be change later. For details, see "4.10 Changing a Project Name".

Caution
Workspace names
Workspace names are used as folder names in Windows, so you can not use characters that can not
be used in Windows folders names ( ¥ / : * ? “ < > | ).

Once a workspace has been created, you can not change its
name.
Be aware that once a workspace has been created, you can not change its name.
To change the name of a workspace, select "Workspace"on the menu → "Save As", save with the
name you want to change to, then delete the original workspace with the old name.

4-43 4-43
4.3. Opening an Existing Workspace

To open an already existing workspace, click [Workspace] -> [Open] or click (Ctrl + O). After selecting
the workspace to edit, click the [OK] button.

Figure 4-5 Opening a Workspace

The names of the last up to four workspaces used are added to [Workspace] on the menu bar. You can
open one of these workspaces by clicking its name here.

The recently used

workspaces are added.
When you click one of these
workspace names, the
workspace is opened.

Figure 4-6 Recently Used Workspace Names

4.4. Closing a Workspace

To close the workspace being edited, click [Workspace] -> [Close]. Note that to delete a workspce, you must
close it first.

4-44 4-44
4.5. Deleting a Workspace
Click [Workspace] -> [Delete]. The "Delete Workspace" screen is displayed, so check the name of the
workspace to delete, then click the [OK] button.

Figure 4-7 Deleting a Workspace

Caution
Deleting a workspace
To delete a workspace, close that workspace. You can not delete a workspace that is being edited.

4.6. Saving a Workspace

The information added to the workspace is saved automatically.

You can also save a workspace with a different name. Click [Workspace] -> [Save As], input the new workspace
name and title, then click the [OK] button.

Figure 4-8 Save As

4-45 4-45
4.7. Changing a Workspace Name
Once a workspace has been created, you can not directly change its name. To change a workspace
name, use the menu bar [Workspace] -> [Save As] to save the workspace with the desired new name, then
delete the old workspace.

4.8. Changing a Workspace Title

You can change the title of a workspace even after it has been created.
Click the name of the workspace with the right button on the mouse, then click "Edit workspace title" on the right
button menu. The workspace title screen is displayed, so input the new workspace title, then click the [OK]
button.

Figure 4-9 Changing a Title

4-46 4-46
4.9. Adding a Project
You can create up to 32 projects in one workspace.
Click [Workspace] -> [Add Project].

Figure 4-10 Adding a Project

Set the project name, information on the robot connected, and the communication method, then click the [OK]
button.
The project is added to the workspace.

Projects can also be added from a project tree.

After selecting the workspace, use the mouse right button to select [Add project].

Figure 4-11 Adding a Project from a Project Tree

4-47 4-47
4.10. Changing a Project Name
You can change the name of a project even after it has been created.
Click the name of the project with the right button on the mouse, then click "Edit Project" on the right button
menu. The project edit screen is displayed, so input the new workspace title, then click the [OK] button.

Figure 4-12 Changing a Project Name

4.11. Deleting a Project

A project can not be deleted when it is running a simulation or has a robot connected online.
Click the name of the project with the right button on the mouse, then click "Delete Project" on the right button
menu. The deletion confirmation message is displayed, so check that you have clicked the correct project
name, then click the [OK] button.

Figure 4-13 Deleting a Project

4-48 4-48
4.12. Contents of Project Tree
A project tree shows the current workspace's project configuration in a hierarchical manner. You can start all
functions from the project tree, including program editing, monitor, etc.
The contents of the project tree depend on the state of connection with the robot controller.

Items are displayed for (1) Offline

each project.

(2) Online

Project 1
<Project name: RC1>
Connected with the controller.

(3) Backup

Project 2
<Project name: RC2>
Not connected with the controller.

Project 3
<Project name: RC3>
Not connected with the controller.

Figure 4-14 Structure of Project Tree in Workspace

(1) Offline
Displays the information stored in computer.
Displays the currently set robot model and the name of robot programs created.

(2) Online
The "Online" section is displayed when a robot is switched into being connected online with its controller
or starts a simulation. This section displays the connected robot model and the information items that can
be referenced in the controller or a simulation controller.

(3) Backup
Controls the information backed up from the controller.

4.13. Copying Programs Between Projects

To copy or move a created robot program to another project, do this with program management. For details
on the operation methods, see "7.10 Program Management", "7.10.2 Copy", or "7.10.3 Move".

4-49 4-49
4.14. Offline/Online/Simulation
The project status are offline, online, and simulation. The meaning of each status and the contents
displayed in the project tree are shown below.

Table 4-1 RT ToolBox2 Status

Status Explanation Project tree display
Offline Targets files stored on the computer.
When a robot is offline, the icon displayed on the left of
the project name on the project tree turns green and
Offline and Backup are displayed on the project tree.

Online The robot is connected to the robot controller and you can
check and change the information in the controller
When a robot is online, the icon displayed on the left of
the project name on the project tree turns blue and
Offline, Online, and Backup are displayed on the project
tree.
Simulation This targets a virtual robot controller running on the
*This can only be computer and you can check and change the information
used with the in the virtual controller
standard edition. When a simulation is running, the icon displayed on the
left of the project name on the project tree turns blue and
Offline, Online, and Backup are displayed on the project
tree.

When this software starts, it goes into "Offline" status.

Caution
The simulation function only supports the "RT ToolBox2" standard edition. It can not be used with the mini
edition.
Also, please be aware that even with the standard edition, the simulation function can not be used when
Movemaster commands are selected.

To switch among offline, online, and simulation, do so from [Online] on the menu bar or from the tool bar. With
the tool bar, you can switch as follows.

Switch to "Offline".

Switch to "Online".

Switch to "Simulation".

Figure 4-15 Explanation of Tool Bar

4-50 4-50
 The current status and the statuses into which the current status can be switched are as followed.

Table 4-2 Current Status and Switchable Status

Current status Switchable status Menu bar [Online] display Tool bar display
Offline Can be switched to online or
simulation.

Online Can only be switched to offline.

Simulation Can only be switched to offline.

The current status is displayed checked at [Online] on the menu bar.

When switching to online or simulation, if multiple projects are registered in the workspace being edited, the
project selection screen is displayed as in "Figure 4-16 Screen for Selecting Project to Switch Online".
Check only the project to be switched online or to simulation, then click [OK]. Only one project can be
switched to simulation.
This screen is not displayed if there is just one project in the workspace.

Figure 4-16 Screen for Selecting Project to Switch Online

Caution
When using Ethernet, do not set an unconnected controller
"Online".
When using Ethernet, if you try to switch "Online" a robot controller that is not connected, incessant
retries are made, which slows execution. Set "Offline" a robot controller that is not connected or
whose power is Off.

Do not connect from multiple projects to 1 controller at the

same time.
Do not connect from multiple projects to 1 controller at the same time.
Data might not be able to be read correctly referring to the same data.

Do not connect USB to multiple controllers from 1 computer.

When using USB connection, 1 computer can connect to only 1 robot controller. It is also
not possible to connect to multiple controllers by using the USB hub.

4-51 4-51
5. Connecting with the Robot

This explains the method for connecting the robot controller and the computer.
With this software, you must make the communication settings for each project.

5.1. Robots Connected and Types of Communication

When connecting the robot controller and computer, there are the methods shown below. Be aware that the
connection method that can be used is restricted by the robot controller connected.

Table 5-1 Robot Controllers That Can Be Connected and Types of Communication
Robot Controller Communication Type Remarks
CRnD-700 series
USB (*4)

Ethernet(TCP/IP) (*1)

RS-232

CRnQ-700 series
USB

CRnQ
commu Ethernet The PLC Ethernet interface module is
nication (TCP/IP) required.
s
(*2)
RS-232

CRn-500 series
The robot controller must have the "Ethernet
Ethernet(TCP/IP) (*3)
interface" option.

RS-232

(*1) For details on the communication settings on the robot controller side for CRn-700 series controllers,
see "Operations and Detailed Explanation" and "Standard Specifications" in the user's manual for
the robot controller.
(*2) For details on the communication settings on the robot controller side for CRnQ-700 series controllers,
see "Operations and Detailed Explanation" and "Standard Specifications" in the user's manual for
the robot controller.
Moreover, please use the “GX Developer” to set the communication setting of PLC.
(*3) For details on Ethernet connections on the robot controller side for CRn-500 series controllers, see the
"Ethernet Interface Option User's Manual".
(*4) When using USB connection, 1 computer can connect to only 1 robot controller.

5-52 5-52
5.2. Connection Settings
Click the name of the project to display the project tree for with the right button of the mouse, then from the
right button menu, click [Edit Project]. The project edit screen is displayed.

Figure 5-1 Connection Settings

Select the controller to connect to and the communications method, then click the "Detailed Settings" button
to set the details.
Normally, the offline robot settings and the travel platform settings for display are also set according to the
controller connected to.
After you complete the details settings, click the [OK] button.

The detailed settings screen will be explained from the next item.

Caution
Do not connect from multiple projects to 1 controller at the
same time.
Do not connect from multiple projects to 1 controller at the same time.
Data might not be able to be read correctly referring to the same data.

Do not connect USB to multiple controllers from 1 computer.

When using USB connection, 1 computer can connect to only 1 robot controller. It is also
not possible to connect to multiple controllers by using the USB hub.

5-53 5-53
5.2.1. USB Communication Settings

Figure 5-2 USB Communication Settings

Table 5-2 TCP/IPCommunication Setting Items and Default values

Item Explanation Default value
Send timeout Timeout time for sending 3000 msec
Receive Timeout time for receiving 3000 msec
timeout
Retries Number of communication retries 3

When the USB cable is connected to the computer, the screen for installing the USB driver may be displayed.
For details on USB driver installation, see "1.5.3 USB driver (CRnD-700 series robot controller) installation ".

5.2.2. TCP/IP (Ethernet) Communication Settings

Input the IP address assigned to the robot controller connected to, then click the [OK] button.

Figure 5-3 TCP/IP Communication Settings

Table 5-3 TCP/IP Communication Setting Items and Default Values

Item Explanation Default value
IP address Sets the IP address of the robot controller connected to. Blank
Port used Number of the port used for communications 10001
Send timeout Timeout time for sending 1000 msec
Receive Timeout time for receiving 20000 msec
timeout
Retries Number of communication retries 3

For help with the computer side network settings (IP address, subnet mask, default gateway, etc.), ask the
network administrator.

Caution
When connecting to 10 or more robot controllers at the same
time.
When connecting to 10 or more robot controllers at the same time, set the reception timeout time to at
least 10000 msec.

5-54 5-54
5.2.3. RS-232 Communication Settings

Change the RS-232 communication settings to match the robot controller side communications settings.

Figure 5-4 RS-232 Communication Settings

Table 5-4 RS-232 Communication Setting Items and Default Values

Item Explanation Default value
Port used COM1 – COM10 can be selected. COM1
Communications Select from 4800, 9600, and 19200. 9600
speed
Character size 7 or 8 can be selected, but select 8. 8
Parity None, Odd, or Even can be selected. EVEN
Stop bit Select from 1, 1.5, and 2. 2
Send timeout Timeout time for sending 5000 msec
Receive timeout Timeout time for receiving 30000 msec
Retries Number of communication retries 3
Usage protocol Non-Procedural or Procedural can be selected. Procedural

Set the following to perform a high-speed, stable communication.

Baud rate : 19200 bps
Protocol used : Procedural
It is also necessary to change the communication settings of the robot controllers at this time.

5-55 5-55
5.2.4. CRnQ Communications Settings

The CRnQ communication is the method to connect with the CRnQ-700 series controller by using the PLC
Universal model QCPU module or the PLC Ethernet Interface module.
When using RS-232 or USB, please connect to connector of the PLC Universal model QCPU module.
When using Ethernet, please connect to connector of the PLC Ethernet Interface module.

The communication routes are displayed here.

Figure 5-5 CRnQ Communications Settings

On the CRnQ communications setting screen, when you select the computer interface, the communications
routes using the selected interface are displayed at the bottom of the screen. Select the communications route,
then press the [Detailed Settings] button. The detailed settings screen corresponding to the selected
communications route is displayed. These detailed settings will be explained from the next item.

5.2.4.1. When RS-232 is selected

When "RS-232" is selected as the computer interface, the communications routes that can be selected are as
follows.

Table 5-5 Communications Routes That Can Be Selected for "RS-232"

No. Communications routes
1 Serial communications CPU unit connection
2 Serial communications Serial communications other station access through CPU unit
3 Serial communication NET/-0(H) other station access through CPU unit
4 Serial communication CC-Link other station access through CPU unit
5 Serial communication Ethernet other station access through CPU unit
6 Serial communication Serial communication through CPU unit - NET/10(H) other station access
7 Serial communication Serial communication through CPU unit-Ethernet other station access
8 Serial communication NET/10(H) through CPU unit - serial communication other station access
9 Serial communication NET/10(H) through CPU unit - CCLink other station access
10 Serial communication Other station access CCLink - NET/10(H) through CPU unit
11 Serial communication CCLink through CPU unit - Ethernet other station access
12 Serial communication Ethernet through CPU unit - serial communication other station access
13 Serial communication Ethernet through CPU unit - CCLink other station access
14 Serial communication Serial communication connection
15 Serial communication Other station access serial communication through serial communication
16 Serial communication Other station access NET/10(H) through serial communication
17 Serial communication Other station access CC-Link through serial communication
18 Serial communication Other station access Ethernet communication through serial communication

5-56 5-56
 No. Communications routes
19 Serial communication Serial communication through serial communication - NET/10(H) other station
access
20 Serial communication Serial communication through serial communication - Ethernet other station
access
21 Serial communication NET/10(H) through serial communication - serial communication other station
access
22 Serial communication NET/10(H) through serial communication - CCLink other station access
23 Serial communication CCLink through serial communication - NET/10(H) other station access
24 Serial communication CCLink through serial communication - Ethernet other station access
25 Serial communication Ethernet through serial communication - serial communication other station
access
26 Serial communication Ethernet through serial communication - CCLink other station access
27 Serial communication CC-Link other station access through G4
28 Serial communication CCLink through G4 - NET/10(H) other station access
29 Serial communication CC-Link through G4 – Ethernet other station access
30 Serial communication Serial communication other station access through NET/10(H) remote
31 Serial communication NET/10(H) other station access through NET/10(H) remote
32 Serial communication CC-Link other station access through NET/10(H) remote
33 Serial communication Ethernet other station access through NET/10(H) remote
34 Serial communication Serial communication other station access through NET/10(H) remote
35 Serial communication Serial communication through NET/10(H) remote - Ethernet other station
access
36 Serial communication NET/10(H) through NET/10(H) remote - Serial communication other station
access
37 Serial communication NET/10(H) through NET/10(H) remote - CC-Link other station access
38 Serial communication CC-Link through NET/10(H) remote - NET/10(H) other station access
39 Serial communication CC-Link through NET/10(H) remote - Ethernet other station access
40 Serial communication Ethernet through NET/10(H) remote - Serial communication other station
access
41 Serial communication Ethernet through NET/10(H) remote - CC-Link other station access

Figure 5-6 RS-232 (Serial Communication

NET/10(H) through CPU Unit – CCLink Other Station Access) Detailed Settings

For some communications routes that you can select, "(5)Network communication route setting of MNET/10"
and "(6)Coexistence network route setting of C24" can not be set.

5-57 5-57
5.2.4.2. When USB is selected
When "USB" is selected as the computer interface, the communications routes that you can select are the
same as for RS-232. See "Table 5-5 Communications Routes That Can Be Selected for "RS-232"".

Figure 5-7 USB (Serial Communication

NET/10(H) through CPU Unit – Serial Communication Other Station Access) Detailed Settings

For some communications routes that you can select, "(5)Network communication route setting of MNET/10"
and "(6)Coexistence network route setting of C24" can not be set.

5-58 5-58
5.2.4.3. When NET/10(H) is selected
When "NET/10" is selected as the computer interface, the communications routes that you can select are as
follows.

Table 5-6 Communications Routes That Can Be Selected for "NET/10(H)"

No. Communications Route
1 NET/10 board communication Other station access through NET/10(H) unit
2 NET/10 board communication NET/10(H) through NET/10(H) unit – CC-Link other
station access
3 NET/10(H) board communication NET/10(H) through NET/10(H) unit - Serial
communication other station access

Figure 5-8 NET/10(H) (NET/10(H) Board Communication

NET/10(H) through NET/10(H) Unit – CC-Link Other Station Access) Detailed Settings

For some communications routes that you can select, "(5)Network communication route setting of MNET/10"
and "(6)Coexistence network route setting of C24" can not be set.

5-59 5-59
5.2.4.4. When CC-Link is selected
When "CC-Link" is selected as the computer interface, the communications routes that you can select are as
follows.

Table 5-7 Communications Routes That Can Be Selected for "CC-Link"

No. Communications Route
1 CC-Link board communication Other station access through CC-link unit
2 CC-Link board communication CC-Link through CC-link unit – NET/10(H) other
station access
3 CC-Link board communication CC-Link through CC-link unit – Ethernet other
station access

Figure 5-9 CC-Link (CC-Link Board Communication

CC-Link through CC-Link Unit – NET/10(H) Other Station Access) Detailed Settings

For some communications routes that you can select, "(5)Network communication route setting of MNET/10"
and "(6)Coexistence network route setting of C24" can not be set.

5-60 5-60
5.2.4.5. When Ethernet is selected
When "Ethernet" is selected as the computer interface, the communications routes that you can select are as
follows.

Table 5-8 Communications Routes That Can Be Selected for "Ethernet"

No. Communications Route
1 Ethernet board communication Other station access through Ethernet unit
2 Ethernet board communication Ethernet through Ethernet unit – Serial
communication other station access
3 Ethernet board communication Ethernet through Ethernet unit – CC-Link other station
access

Figure 5-10 Ethernet (Ethernet Board Communication

Ethernet through Ethernet Unit – Serial Communication Other Station Access) Detailed Settings

For some communications routes that you can select, "(5)Network communication route setting of MNET/10"
and "(6)Coexistence network route setting of C24" can not be set.

5-61 5-61
5.2.4.6. When Q series bus is selected
When the "Q series bus" is selected as the computer interface, the communication route that can be selected
is as follows.

Table 5-9 Communication Route That Can Be Selected with the "Q Series Bus"
No. Communications Route
1 Q bus communications CPU unit connection

Figure 5-11 Q Series Bus (Q Bus Communications CPU Unit Connection) Detailed Settings

5-62 5-62
6. Robot Program Language Setting
This switches the robot program language used. The languages you can switch to are as follows.

Table 6-1 Robot Program Languages for Each Controller

Robot program language
Robot controller Movemaster
MELFA-BASIC V MELFA-BASIC IV
command
CRnD-700 series ○ ○ ○
CRnQ-700 series ○ ○ ○
CRn-500 series × ○ ○

The Movemaster commands are restricted by the robot models that can be used. Before trying to use
Movemaster commands, check in the "Standard Specifications" that the model you are using supports
Movemaster commands.
Also, this software allows you to select Movemaster commands for CRnD-700 series and CRnQ-700 series
robot controllers, but these robot controllers themselves do not actually support Movemaster commands. (As
of December 2007)

Caution
When Movemaster commands are used, the simulation functions
cannot be used.

On the project tree, click the desired project name with the right mouse button, then from the right button
menu, select "Edit Project". The project edit screen is displayed.

Figure 6-1 Connection Settings

Select the controller connected, the robot model, and the robot language used, then click the [OK] button

6-63 6-63
7. Writing Programs
This chapter explains robot program editing methods. You can directly edit programs in the robot controller
or edit programs stored on the computer.

Caution
Program names that can not be handled on the computer
If a program name in the robot controller is the same as a "reserved term" in Windows, when you try to open
that program for program editing, this causes an error. In this case, it is necessary to change the program name
in the controller.
"Reserved terms" are special character strings that the Windows system uses and therefore can not be used
as file names. These "reserved terms" are character strings such as the following.

AUX, COM1 to COM9, CON, LPT1 to 9, NUL, PRN

7.1. Writing a New Program

7.1.1. Writing a new program on the computer

For the new program you are going to write, select [Offline] -> [Program], then click the right mouse button.
The right button menu is displayed, so click [New].

Figure 7-1 Writing a New Program on the Computer

Input the robot program name, then click the [OK] button.

Caution
Folder in which programs are stored
Programs on the computer are managed in units of workspace projects. The folder they are stored into is
workspace writing folder¥project name¥Program.
To store into any other folder, first store in this folder, then copy into the desired folder with the program
management copy function.

7-64 7-64
7.1.2. Writing a new program in the robot controller

For the new program you are going to write, select [Online] -> [Program], then click the right mouse button.
The right button menu is displayed, so click [New].

Figure 7-2 Writing a New Program in a Robot Controller

Input the robot program name, then click the [OK] button. The "Read Item" screen is displayed, so check
the read items, then click the [OK] button. For details on the read items, see "7.2.3 Read Items when
opening program in robot controller".

Figure 7-3 Editing a New Program

7-65 7-65
7.2. Opening an Existing Program
7.2.1. Opening an existing program on the computer

Open the target project in the project tree with [Offline] -> [Program]. The stored programs are displayed on
the project tree, so double click the program you want to edit.

Figure 7-4 Opening a Program on the Computer

7.2.2. Opening a program in a robot controller

Open the target project in the project tree with [Online] -> [Program]. The stored programs are displayed on
the project tree, so double click the program you want to edit.

Figure 7-5 Opening a Program in a Robot Controller

Input the robot program name, then click the [OK] button. The "Read Item" screen is displayed, so check
the read items, then click the [OK] button. For details on the read items, see "7.2.3 Read Items when
opening program in robot controller".

7-66 7-66
7.2.3. Read Items when opening program in robot controller

You can set the robot program read items divided into command lines, position variables, and program
external position variables. This function is displayed after H1 edition on CRn-500 series controller.

The default values of read items are as follows.

Figure 7-6 Read Items

The program external position variable read operations are shown in "Table 7-1 ". (For details on program
external position variables, see "Details of functions and operations" in the robot controller's user's manual.)

Table 7-1 Program External Position Variable Read Operations

Read Item
Position variable, joint variable
Position array variable,
Command

(P_01, J_02, etc.)

Position

variable

joint array variable

External
position

(MOVEMASTER command :
(P_100( ), J_102( ), etc.)
901-999)

Reads only the external position Reads all elements used in

variables (position variables, joint instruction statements. (*2)
CRn-700 variables) used in instruction
series robot statements. (*1)
controller
Reads all external position variables (position variables, joint
variables, position array variables, joint array variables).

Reads only the external position Reads all elements used in

variables (position variables, joint instruction statements. (*2)
Ver.J1 or later

variables) used in instruction

statements. (*1)
CRn-500 series robot controller's

Reads all external position variables (position variables, joint

variables, position array variables, joint array variables).
software version

Ver.H1 to H7

Reads all external position variables (position variables, joint

variables, position array variables, joint array variables).
orearlier
Ver.G9

This screen is not displayed.

*1: When Movemaster commands are used, all external position variables are read.
*2: When only P_100(1) is used in the command statement, P_100(1) to P_100(10) are all read. However, the number
of valid elements depends on the robot controller software version used.

7-67 7-67
7.3. Explanation of Program Edit screen
This explains the program edit screen.

Command edit screen

Moves up and down.

Position variable edit screen

Figure 7-7 Explanation of Program Edit screen

The top part of the screen is the program command statement edit screen and the bottom part is the
position variable edit screen.
To change the position dividing the top and bottom screens, drag the border line with the mouse. This is
handy when you want to expand the command edit screen, for example because there are many lines of
commands.
This edit screen display area can be customized. For details, see "7.5.1 Changing the display area".

Also, the background color for the command edit screen depends on the robot language used.

Table 7-2 Command Edit Screen Background Color

Background color
Robot language
Normal Debugging
MELFA-BASIC V White
MELFA-BASIC IV Light yellow Light blue
Movemaster commands Light green
Debugging means when the program is opened in debugging status.

7-68 7-68
7.4. Program Editing Menu Bar
During program editing "File", "Edit", "Debug", and "Tool" are added to the menu bar.

Figure 7-8 Program Editing Menu Bar

The menus are as follows.

Menu item Explanation Menu item
File Save Saves the program being edited 7.7.1
with its current name.
Save As -> Saves the program being edited 7.7.2
PC with its current name on the PC
Save As -> Saves the program being edited 7.7.3
Robot with its current name on Robot
controller
Page Setup You can customize the pages the 7.8.3
program is printed with.
Edit Undo Cancel the edition by the command
and return to the previous state
Undo - Cancel the edition by the position
Position variable and return to the previous
variable state
Cut Cuts a character string from the 7.6.4.2
command being edited.
Copy Copies a character string in the 7.6.4.1
command being edited.
Paste Pastes the copied or cut character 7.6.4.3
string to the specified location.
Copy - Copies position data. 7.6.4.4
Position
variable
Paste - This pastes the copied position 7.6.4.5
Position data.
variable
Find This searches for the specified 7.6.4.6
character string.
Find in Files This searches for the specified 7.6.4.7
character string in the program
files.
Replace This replaces the specified 7.6.4.8
character string with another
character string.
Jump Jumps to the specified step 7.6.4.9
number or label.
Partial Writes the selected program lines 7.6.4.10
transmission to the robot controller.
This can not be used when the
program is opened in debugging
status.
Edit Edit the command lines for a 7.9.3
Command program pened in debugging
line - Online status.
Insert Insert the command lines for a
Command program opened in debugging
line - Online status.
Delete Delete the command lines for a
Command program opened in debugging
line - Online status.

7-69 7-69
 Menu item Explanation Menu item
Debug Set a You can set a breakpoint in a 7.9.4
Breakpoint program opened in debugging
status.
Delete a You can delete a breakpoint in a
Breakpoint program opened in debugging
status.
(This can only operate when the Delete all You can delete all breakpoints in a
program has been opened in debugging Breakpoints program opened in debugging
status.) status
Show the You can set to dispplay/not to 7.9.1
executed line display the executed line always to
always the program opened in debugging
status.
Tool Renumber The renumbering function can only 7.6.4.14
be used with MELFA-BASIC IV and
Movemaster commands.
You can renumber line numbers in
a batch.
Sort The sorting function can only be 7.6.4.15
used with MELFA-BASIC IV and
Movemaster commands.
This sorts the edited program by
line number.
Syntax You can check whether or not the 7.6.4.11
Check edited robot program is
(This can not operate when the program syntactically correct.
has been opened in debugging status.) Command You can display a list of the 7.6.4.12
Template commands and make insertions on
Renumbering and sorting can only be the program command edit screen.
used with MELFA-BASIC IV and XYZ Position You can change the position 7.6.4.13
Movemaster commands. variable variables in the program being
Batch Edit edited in a batch and can sum up
Tact time calculation can only be used Joint all the values
in a simulation. Position
variable
Batch Edit
Tact time Tact time calculation can only be 13.12
calculation used in a simulation.
Tact time of the program can be
calculated.
Option You can customize the program 7.5
edit area, screen display area and 7.7.5
syntax check before saving a
program

7-70 7-70
7.5. Customizing the Program Edit Screen
You can customize the program edit screen.
With the program opened, on the menu bar, click [Tool] -> [Option] and set the program edit screen as you
want with the displayed option screen.
Clicking the [Restore Defaults] button restores the default settings.

Figure 7-9 Option Screen

7.5.1. Changing the display area

In the "Display area" group, you can set the command display area and position edit area display ratios and
for the position edit area, the XYZ (P) variable and joint (J) variable proportions.

Figure 7-10 Program Edit Screen Display Area Change

7-71 7-71
7.5.2. Command format hints
You can use pop-up hint display to display the format for the robot program command, system functions, and
system status variables displayed in the command edit area.

Figure 7-11 Command Edit Area Command Format Hint Display Settings

7.5.3. Character colors

You can assign the colors for displaying robot program command, system functions, and system status
variables displayed in the command edit area.

Figure 7-12 Command Edit Area Character Color Settings

7-72 7-72
7.5.4. Changing the font
You can change the font displayed in the command edit area.
Click the option screen font [Change] button. The font setting screen is displayed, so after setting the font
name, style, and size, click the [OK] button.

Figure 7-13 Command Edit Area Font Setting

7-73 7-73
7.6. Program Editing
This chapter explains the methods for editing MELFA-BASIC V programs.
For RT ToolBox2 command statement editing, you can input in the same way as with a general editor like a
notebook. There is no need to input the [Enter] key for each line as was the case with RT ToolBox.

7.6.1. MELFA-BASIC V command statement editing

When writing a program using MELFA-BASIC V, you do not use line numbers, unlike MELFA-BASIC IV or
Movemaster commands. Instead the step position is displayed on the left end. These step numbers are
automatically displayed with the keyboard [Enter] key.

Step number

Figure 7-14 MELFA-BASIC V Command Edit Screen

Even if you input MELFA-BASIC V commands with all lowercase characters, when the program is written to
the robot controllers, the commands are converted into the correct mixture of uppercase and lowercase letters.

When this is written to the robot

controller, it is converted into
uppercase and lowercase
characters in correct
MELFA-BASIC V format.

Figure 7-15 MELFA-BASIC V Character Input

7-74 7-74
7.6.2. MELFA-BASIC IV and Movemaster command command statement editing
When writing a program using MELFA-BASIC IV or Movemaster commands, step numbers like those of
MELFA-BASIC V are not displayed. Input the line number at the front of the command statement.

Figure 7-16 MELFA-BASIC IV Command Edit screen

Caution
For MELFA-BASIC IV and Movemaster commands, input line numbers.
Step numbers are not displayed on the MELFA-BASIC IV and Movemaster command edit screen. When using
MELFA-BASIC IV and Movemaster commands, always input line numbers.
If there are no line numbers, this is a syntax error.

Line numbers
OK

Syntax error

There is a function for sorting commands in order of line number even if you do not input them in order of line
numbers. For details, see "7.6.4.15 Sorting".

Figure 7-17 Sorting

There is a function for reordering commands in order of line number even if you do not input them in order of
line numbers. For details, see

When this is written to the

robot controller, it is
converted into all
uppercase characters,
which is correct
MELFA-BASIC IV format.

Figure 7-18 MELFA-BASIC IV Character Input

7-75 7-75
7.6.3. Position variable editing
Position variables are edited on the position edit screen. The upper list is a list of XYZ coordinate variables
and the lower list is a list of joint coordinate variables.

XYZ position variables

Joint position
variables

Figure 7-19 Position Variable Edit Screen

Array variables are displayed developed in their own lists.

Figure 7-20 Array Variable Display

Caution
About uppercase characters and lowercase characters in position
variables names
With MELFA-BASIC V, you can use lowercase letters in variable names.
This software does not differentiate between uppercase letters and lowercase letters in variable names.
For example, the position variables PA and pa are recognized as the same position variables.
The controller converts all later variables to match the first position variable name defined. For example, if
you write a program like that below, the position variable "pa" is used and "PA" is converted into "pa".

When this is written to the robot controller, it is

converted as on the right.

7-76 7-76
7.6.3.1. Adding/changing position variables
To add a position variable, click the [Add] button. The position variable add screen is displayed. At this time, if
position data is selected in the list, the contents of that position data (XYZ/joint, position information) are
displayed. However, the variable name remains blank.

To revise a position variable, select the position variable to be revised in the list, then click the [Change]
button.
The selected position variable is displayed. At this time, the variable name can not be changed.

Select either XYZ coordinate type or joint coordinate type, input the values of each element of the position
data, input the position variable name, then click the [OK] button.
While editing an online program in online status or simulation status, you can read the current robot position
by pressing the [Read Current Position] button.

The validity of the elements is

checked. For some robot
models, some elements are not
checked.

Figure 7-21 Position Data Variables

Caution
When adding a position array variable, specify the array name and element numbers as the variable name.
Also, when writing to a robot, always write the Dim declaration in a command statement. If there is no Dim
declaration, an error occurs when you write to the robot controller.

Caution
The units for elements used depend on the robot. See the robot's own operations manual.

7-77 7-77
7.6.3.2. Deleting position variables
After selecting the target position variable, click the [Delete] button. The selected position variable is deleted.
You can also delete multiple position variables at the same time. You can select multiple position variables by
clicking position variables while holding down the [Ctrl] key or the [Shift] key on the keyboard. However, you
cannot select XYZ position variables and joint position variables at the same time.

Caution
To delete a position array variable, delete the command statement.
"Dim" declaration.
With this software, even if a position variable is deleted, if a program with a "Dim" declaration is written to a
robot controller, the position array variables declared with the "Dim" are left with 0 for all their components.

7.6.4. Edit assist functions

This explains the edit assist functions, which help in command editing.

Edit assist functions such as copy, cut, find, find and replace, and jump are used from [Edit] and [Tool] on
the menu bar.

7.6.4.1. Copy
Copies a character string in the command being edited. You can also copy multiple lines.
After selecting the character string to be copied, click on the menu bar [Edit] -> [Copy].
You can use the paste function, explained below, to paste this copied character string to another location in
the program.
For details on position data copying, see "7.6.4.4 Copy position data".

7.6.4.2. Cut
Cuts a character string from the command being edited. You can also cut multiple lines.
After selecting the character string to be cut, click on the menu bar [Edit] -> [Cut].
You can use the paste function, explained below, to paste this cut character string to another location in the
program.

7.6.4.3. Paste
Pastes the copied or cut character string to the specified location.
Put the cursor where you want to paste, then click on the menu bar [Edit] -> [Paste]. The copied or cut
character string is inserted at the specified location.
For details on position data pasting, see "7.6.4.5 Pasting position data".

7.6.4.4. Copy position data

Copies position data. You can also copy multiple position data items.
After selecting the position data to be copied, click on the menu bar [Edit] -> [Copy – Position data].

7-78 7-78
7.6.4.5. Pasting position data
This pastes the copied position data.
Make active the program you want to paste into, then click on the menu bar [Edit] -> [Paste – Position data].
The copied position data is inserted into the specified program.
At this time, if there is already position data with the same name in that program, a confirmation message is
displayed.

Figure 7-22 Paste Position Data Confirmation Message

7.6.4.6. Find
This searches for the specified character string.
Click the menu bar [Edit] -> [Find]. The find screen is displayed.

Figure 7-23 Find Screen

Input the character string to find, then click [Find Next] or [Find Previous]. The character string search starts.

If you click [Display List], all the instances of the specified character string are found from programs and
displayed in a list.

Figure 7-24 Find Results List Display

When you select an item from the find results list and click the [Jump] button, the display jumps to the line that
includes the selected item.

7-79 7-79
7.6.4.7. Find in Files
This searches for the specified character string in the "Online" or "Offline" program files registered in the
current project.
Click the menu bar [Edit] -> [Find in Files]. The find in files screen is displayed.
You can also display this screen by clicking the program management [Find in Files] button.

Figure 7-25 Find in Files Screen

Input the character string to find and select the location to search.
When "PC" is selected as the location to search, all the offline programs registered in the current project are
searched.
When "Robot" is selected as the location to search, all the online programs registered in the current project
are searched. In other words, all the programs in robot controllers in the "online" status connected to a robot are
searched. If a simulation is running, all the programs in the virtual controller are searched. When you search in
controllers, the communications with the controllers may take time.

Figure 7-26 Results of Search from File

C:/・・・・・・/RC1/Program/P01.prg (2): 2 Mov P02

Line contents
Folder in which workspace Fixed Number of
is created steps
Project name Program
name Number of lines from head

With the [Open with Program edit] button, you can open the program that includes the contents of the line
selected from the list of search results.

7-80 7-80
7.6.4.8. Replace
This replaces the specified character string with another character string.
Click the menu bar [Edit] -> [Replace]. The Replace Screen is displayed.

Figure 7-27 Replace Screen

[Find Next] : Searches for the next instance of the character string to be replaced.
[Replace] : Replaces the found character string.
[Replace All] : An item is displayed for specifying the range in which to replace all instances of the
specified character string.

With Replace All, you can specify a range in which to replace.

When you click the [Replace All] button, all the instances in the specified range are replaced.

Figure 7-28 Replace All Setting Screen

7.6.4.9. Jump to specified line

Jumps to the specified step number or label.
Click on the menu bar [Edit] -> [Jump]. The jump screen is displayed.

Figure 7-29 Jump Screen

Input the step number or label to jump to, then click the [OK] button. Display jumps to the specified step
number or label.

7-81 7-81
7.6.4.10. Partial writing
Writes the selected program lines to the robot controller.
This is handy for reflecting the contents of the partially revised program in the robot controller, but be careful.
Only the selected part of the program is written.
Select the lines to be written to the robot controller, then click on the menu bar [Edit] -> [Partial Write].
Check the contents to be written, then click [Yes].

Figure 7-30 Partial Writing

7.6.4.11. Syntax check

You can check whether or not the edited robot program is syntactically correct. Execute this before writing the
program to the robot controller.
Click on the menu bar [Tool] -> [Check Syntax]. If there is a syntax error, the error location and details are
displayed.

Figure 7-31 Syntax Check Results Screen

If you select the detected error and click the [Jump] button, it jumps to the command statement with the error.

7-82 7-82
7.6.4.12. Command template
You can display a list of the commands and make insertions on the program command edit screen.
Click on the menu bar [Tool] -> [Command Template].

Figure 7-32 Command Template

When you select the template for the selected command from the list, then either click the [Insert Template]
button or double click, the command is inserted onto the program command edit screen.

7.6.4.13. XYZ position data batch editing/joint position data editing

You can change the position variables in the program being edited in a batch and can sum up all the values.
For example, you can add 10.00 to the X components of the P00, P01, P02, P03, and P04.

To batch edit XYZ position variables, click on the menu bar [Tool] -> [Batch Edit XYZ Position Data].
To batch edit joint position variables, click on the menu bar [Tool] -> [Batch Edit Joint Position Data].
All the position variables of the respective type are displayed.

Figure 7-33 XYZ Position Data Variable Editing

From the position variable list, select the position variable to change, then add it to the change list with the [->]
button.
Input the change value, select the change method [Add] / [Change], then click the [OK] button. You can not
set both [Add] and [Change] for the same element.

You can cancel the registration of a position variable for change with the [<-] button.

7-83 7-83
7.6.4.14. Renumbering
The renumbering function can only be used with MELFA-BASIC IV and Movemaster commands.
You can renumber line numbers in a batch. You can specify the range for renumbering.
With the setting dialog, you can specify the start and end lines numbers, the new starting line number, and the
line number interval.

While editing a program created with MELFA-BASIC IV or Movemaster commands, click the tool bar [Tool] ->
[Renumber]. The renumber set screen is displayed.

Figure 7-34 Renumber Setting Screen

Caution
Renumbering can only be used with MELFA-BASIC IV and
Movemaster commands.
The renumbering function can only be used with MELFA-BASIC IV and Movemaster commands. It can not
be used with standard MELFA-BASIC V.

7.6.4.15. Sorting
The sorting function can only be used with MELFA-BASIC IV and Movemaster commands.
This sorts the edited program by line number.
While editing a program created with MELFA-BASIC IV or Movemaster commands, click the tool bar [Tool] ->
[Sort]. The confirmation message is displayed, then the line numbers are sorted in ascending order.

Figure 7-35 Sorting

Caution
Sorting can only be used with MELFA-BASIC IV and Movemaster
commands.
The sorting function can only be used with MELFA-BASIC IV and Movemaster commands. It can not be
used with standard MELFA-BASIC V.

7-84 7-84
7.7. Saving Programs
Always save the edited program.
There are three methods for saving: saving, saving to computer, saving to robot controller.

Caution
Do not write a program to the controller with duplicate step
numbers.
Even programs with duplicate step numbers or that are still being edited and are not yet syntactically
correct can be saved on the computer. However, be careful not to copy or otherwise transfer such a program
to a robot controller with the program management functions.
If a program with duplicate step numbers is written to the robot controller, the duplicate step lines are written
over each other.

7.7.1. Save
Saves the program being edited with its current name.
When you click on the menu bar [File] -> [Save], the program is saved, overwriting the older version of itself.

If you are editing a program on a robot controller, the "Save Items" setting screen is displayed. Set the items
to write, then click the [OK] button.
For details on the "save items", see"7.7.4 Items written when saving in robot".

Figure 7-36 Writing Items

7-85 7-85
7.7.2. Saving on computer
Saves the program being edited to the computer. At this time, you can set a new program name.
Click on the menu bar [File] -> [Save to PC].

Figure 7-37 Saving on Computer

Input the robot program name, then click the [OK] button.

Caution
Folder in which programs are stored
Programs on the computer are managed in units of workspace projects. The folder they are stored into is
workspace writing folder/project name/Program.
To store into any other folder, first store in this folder, then copy into the desired folder with the program
management copy function.

Caution
About the program name which is disable on PC
Windows, error is occurred in the Program editing tool when opening that program. To solve this problem, it
is necessary to change the program name in the robot controller.
The “Reserved words” are the special words used by Windows system. Therefore, it is impossible to use
these words as the file name on PC. The following words are in “Reserved words”.

AUX, COM1 to 9, CON, LPT1 to 9, NUL, PRN

7-86 7-86
7.7.3. Saving in robot controller
Saves the program being edited to the robot controller with a new name. At time, you can set a new program
name.
Click on the menu bar [File] -> [Save in Robot]. The "Save Items" setting screen is displayed, so set the save
items, then click the [OK] button.
For details on the "save items", see "7.7.4 Items written when saving in robot".

Figure 7-38 Saving on Robot Controller

7-87 7-87
7.7.4. Items written when saving in robot
When saving a robot program in a robot controller, write items can be set by categorizing them into
instructions, position variables and program external position variables.
This function is displayed on CRn-500 series robot controllers from the H1 edition on.

This save item default values for when you have read a robot controller program are the same as the "Read
Items" when you read the program. When you have created a new program or opened a program on the
computer, the display becomes as in "Figure 7-39 Save Items".

Figure 7-39 Save Items

We will explain the operations for saving to a robot when only command lines or only position variables
are specified, using the following example for illustration.

Example: When there are programs in program editing on the computer or in

the robot controller

<<Program in the robot controller>> << Program on computer >>

10 Mov P1 100 Mov P1
20 Mov P2 200 Mov P2
30 Mov P3 300 Mov P5 ‘ <- Change
40 End 400 End
P1=( 400.000, 0.000, 100.000, , , 90.000)(4,0) P1=( 400.000, 0.000, 100.000, , ,-90.000)(4,0)
P2=( 0.000, 400.000, 150.000, , , 0.000)(4,0) P2=( 0.000, 400.000, 150.000, , , 0.000)(4,0)
P3=(-351.704, -49.369, 22.000, , ,-95.168)(0,0) P3=(-351.704, -49.369, 22.000, , ,-95.168)(0,0)
P4=( 276.499,-599.066, 264.966, , , 29.170)(0,0) P5=( 535.786, 295.021, 102.000, , ,148.420)(0,0)

(1) When only command line written

<<Program in the robot controller>>

100 Mov P1
200 Mov P2 Changing only the command line
300 Mov P5
400 End
P1=( 400.000, 0.000, 100.000,,, 90.000)(4,0)
P2=( 0.000, 400.000, 150.000,,, 0.000)(4,0) The position variables are not
P3=(-351.700, -49.370, 22.000,,,-95.170)(0,0) changed.
P4=( 276.500,-599.070, 264.970,,, 29.170)(0,0)

(2) When writing position variable only

<<Program in the robot controller >>

10 Mov P1
20 Mov P2 The command line is not changed.
30 Mov P3
40 End The position variables on the computer are
P1=( 400.000, 0.000, 100.000,,,-90.000)(4,0) overwritten. However, position variables
P2=( 0.000, 400.000, 150.000,,, 0.000)(4,0) that are in the robot controller, not on the
P3=(-351.700, -49.370, 22.000,,,-95.170)(0,0) computer, are left as is. (Reference)
P4=( 276.500,-599.070, 264.970,,, 29.170)(0,0)
P5=( 535.790, 295.020, 102.000,,,148.420)(0,0)

7-88 7-88
7.7.5. Setting the syntax check for before program saving
You can set whether or not to have the syntax checked when you save a program and whether or not to
display a message when there are no syntax errors.
With the program opened, on the menu bar, click [Tool] -> [Option] and set with the option screen.
The default setting is automatic syntax checks with no message displayed if there is no syntax error.

Figure 7-40 Settings for Syntax Check Before Saving

7-89 7-89
7.8. Program Printing
You can print programs you have written.

7.8.1. Checking a print image

You can display a print image of the program on the screen.
Make active the program you want to print, then click on the menu bar [Workspace] -> [Print Preview]. The
print image for currently active program is displayed.

7.8.2. Printing a program

Make active the program you want to print, then click on the menu bar [Workspace] -> [Print]. The currently
active program can be printed.

7.8.3. Setting to print a program

You can customize the pages the program is printed with.
When you click on the menu bar [File] -> [Page Setup], the page setup screen is displayed.
You can set whether or not to print the file name, print date and time, and page numbers, the space between
lines and the margin sizes.

Figure 7-41 Page Setup for Printing

7-90 7-90
7.9. Program Debugging
You can debug robot programs you have written.

Caution
Debugging is for programs on a controller or on a virtual controller
with a simulation running.
When debugging, use a program on a controller or on a virtual controller with a simulation running. You can
not debug a program stored on a computer.

7.9.1. Starting debugging

Open the robot program in debugging status. From the project tree [Online] -> [Program], select the program,
then click the right mouse button. From the right mouse button menu, click [Debug Open].

Figure 7-42 Opening a Program in Debug Status

The specified robot program is opened in debugging status. The execution line cursor " " is displayed at the
left end of the command edit area. The line on which this execution line cursor is displayed is the line currently
being executed.
The display of this execution line cursor can be switched on/off with the menu bar [Debug] -> [Display/Do not
display Execution Line].

7-91 7-91
7.9.2. Executing programs step by step

Danger
With program debugging, the robot may operate at 100% speed.
Watch out for the safety around the robot.
Also, prepare a T/B at hand and use the robot in a status in which an
emergency stop can be made at any time.

A program that has been opened in debugging status can be run step by step.
Operate using the debug operation screen that is displayed at the same time the program was opened in
debugging status.

(1) Status

(2) OVRD

(5) Step Execution

(3) Jump

(6) Continuous Execution

(4) Stop
(8) Reset
(7) Servo On/Off (9) Direct Execution

Figure 7-43 Debug Operation Screen

(1) Status
The controller's task slot status is displayed.

(2) OVRD
This displays and sets the robot speed override.

(3) Jump
You can specify the line in the program to execute.

(4) Stop
You can stop the program.

(5) Step Execution

This executes the specified program one line at a time. Pressing the [FORWD] button executes the
command on the current execution line and advances the current execution line one line. Pressing the
[BACKWD] button executes the command on the current execution line and returns the current execution
line one line.

(6) Continuous Execution

This executes the program continuously from the current line.

(7) Servo On/Off

You can switch the robot servo On/Off.

(8) Reset
You can reset the program and any errors that have occurred.

(9) Direct Execution

You can execute any command without relationship to the robot program.

7-92 7-92
7.9.3. Revising programs
The command statements for a program that has been opened in debugging status can not be edited in the
command edit area. You can revise command statements from [Edit] on the menu bar. Click on the menu bar
[Edit] -> [Edit Command line (Online)], [Insert Command line (Online)], and [Delete Command line (Online)].
Position variables can be edited as usual.

(1) Edit command line

You can edit the contents of the specified command line.
Click the command line to be edited with the mouse, click on the menu bar [Edit] -> [Edit Command line
(Online)]. The screen for editing the command line is displayed.

Figure 7-44 Command Line Editing (Online)

Revise the command line, then click the [OK] button.

(2) Insert command line

You can insert a command statement at the specified line.
Click the line at which the command statement is to be inserted with the mouse, then click on the menu bar
[Edit] -> [Insert Command line (Online)]. The screen for inserting the command line is displayed.

Figure 7-45 Command Line Insertion (Online)

(3) Delete command line

You can delete the specified command line.
Click the line at the line with the command statement to be deleted with the mouse, then click on the menu
bar [Edit] -> [Delete Command line (Online)]. The confirmation screen for the command line deletion is
displayed.

Figure 7-46 Confirming Command Line Deletion

7-93 7-93
(4) Edit position variables
For details on the method for editing the position variable, "7.6.3 Position variable editing".

Caution
Be careful when changing the value of a variable.
When you change the value of a variable, the operation target position of the robot may change and result in a
collision. This is particularly dangerous during robot operation, so check carefully before changing the value of a
parameter.

Caution
Partial writing can not be performed while editing a program in
debugging status.

7.9.4. Setting and deleting breakpoints

You can set a breakpoint in a program that has been opened in debugging status.
If you set a breakpoint, when you open the program in debugging status, you can stop the program at the
line while executing the Continuous execution. After stops, you can execute the program continuously.

Breakpoints can be set up to 128. Moreover, when the program is quitted, every breakpoint is deleted.
There are the following two types of breakpoints.
Permanent breakpoint : After stopping, the breakpoint keeps being set.
One-time breakpoint : After stopping, the breakpoint is automatically deleted at the same time
as stopping.

Caution
Breakpoints can only be used with MELFA-BASIC V.

(1) Set a Breakpoint

The breakpoint is set according to the following procedure.
1) Click the command line where breakpoint is set with the mouse, then click on the menu bar [Debug]
-> [Set Breakpoint].

2) The breakpoint setting screen is displayed.

Select the type of breakpoint to set, then click the [OK] button. The breakpoint is set at the specified
command line.

Figure 7-47 Setting a Breakpoint

7-94 7-94
 3) " " is displayed at the left end of command lines at which breakpoints are set.

Figure 7-48 Display of Lines with Breakpoints Set

(2) Delete a Breakpoint

To delete a breakpoint, click the command line with the breakpoint to be deleted with the mouse, then
click on the menu bar [Debug] -> [Delete a Breakpoint].
To delete all the breakpoints set in this program, click on the menu bar [Debug] -> [Delete All
Breakpoints].

You can also perform the breakpoint setting and deleting operations with tool bar buttons.

This deletes the breakpoint at the This deletes the breakpoint at the
command line under the mouse cursor. command line under the mouse cursor.

Figure 7-49 Setting/Deleting a Breakpoint with theToolbar

7.9.5. Ending debugging

To end debugging, close the program with the " " button at the top right of the edit screen for the program
opened in debugging status.
This closes the program
opened in debugging status.

Figure 7-50 Closing a Program Opened in Debug Status

At this time, if the program has been changed, a confirmation message is displayed asking if you want to
save the changed contents.

Figure 7-51 Confirmation Message for Saving the Changed Contents

Here, if you select "No", the changed contents are all thrown out. To put the changed contents into effect,
always select "Yes".

7-95 7-95
7.10. Program Management
You can copy, move, delete, compare the contents of, rename, and set protection for robot programs.

From the project tree, select the target project program, then click the right mouse button.
The right button menu is displayed, so select [Manage Programs]. The manage programs screen is
displayed.

Figure 7-52 Starting Program Management

Caution
All the operations of these functions are for robot programs.

7-96 7-96
7.10.1. Program list display
On the left and right lists, the lists are programs of the displayed in the robot controller and the specified folder.

① Project You can specify projects in the workspace.

② Robot You can specify a robot controller that is currently connected.
③ […] button When you select [Project], you can specify any folder on the computer.

① Project
③ When you select
② Robot a folder on the
computer

Figure 7-53 Program List Display

7.10.2. Copy
The program files are copied. Copying of the entire program file or only the command statements or only the
position variables is possible.
Select the transmission source program names from the list at the left, and designate the transmission
destination folder on the right side. The multiple transmission source programs can be selected at the same
time, but for copying with changing its name, only one program must be selected. Copying is executed when the
[Copy] button is clicked on and [Setting for copy] dialog is set.

Figure 7-54 Copy Setting Screen

7-97 7-97
7.10.3. Move
The program files can be moved.
Select the transmission source program names from the list at the left, and designate the transmission
destination folder on the right side. The multiple programs can be selected at the same time. Movement is
executed when the [Move] button is clicked on.

7.10.4. Delete
The program files can be deleted.
Select the names of the programs to be deleted from the lists. The multiple programs can be selected at the
same time. The programs can be selected at the both lists. Delete is executed when the [Delete] button is
clicked on.

Caution
That once the program files are deleted, they cannot be recovered.

7.10.5. Rename
A program file name is renamed.
Select the name of the only one program to be renamed from the lists. The program can be selected at the
both lists. Rename is executed when the [Rename] button is clicked on and a new file name is set at the [Setup
for ReName] dialog.

Figure 7-55 Rename Screen

7-98 7-98
7.10.6. Protect settings
The program files in the controller can be protected. The entire program file can be protected, or just the
command statements or position variables can be protected.
You cannot move, delete, or rename a protected file. Release the protection before any of these operations.
Select the names of the programs to be protected from the lists. The multiple programs can be selected at the
same time. The programs can be selected at the both lists. Protect is executed when the [Protect] button is
clicked on and [Setting for protect] dialog is set.

Figure 7-56 Protect Settings Dialog

Caution
The only programs to which protect operations apply are programs in robot
controllers.

7.10.7. Comparison
The program files can be compared. Comparison of only the command statements or only the position
variables is possible. Select the names of the programs to be compared from the left and right lists. A dialog
displaying the corresponding comparison results will appear when the [Compare] button is clicked on and
[Setting for compare] dialog is set.

Figure 7-57 Program Comparison Settingsand Comparison Results

When both files are the same, the result dialog displays nothing.

7-99 7-99
7.11. Program Conversion
You can convert existing robot programs written in a different program language into the currently set
program language.
Table 7-3 Combination list of program conversion
No. Source Target Content
The position data is converted.
1 MELFA-BASIC III MELFA-BASIC IV
If “MELFA-BASIC V” is chosen for the
target, the lines No. are also converted in
2 MELFA-BASIC III MELFA-BASIC V
addition to this conversion.
3 MELFA-BASIC IV MELFA-BASIC V The lines No. are converted.
MOVEMASTER command MOVEMASTER command The position data is converted.
4
(CR-116/356) (CRn-500/700)

There are the following two types of conversion.

For details, see "7.11.2 Line number conversion (from MELFA-BASIC IV to MELFA-BASIC V", "7.11.3
Position data conversion (from E/EN/M1/M2 series to CRn-500/700 series".

(1) Conversion of the lines No.

Convert the line No. and relevant command line, because the deal of line No. in MELFA-BASIC IV is
different from MELFA-BASIC V.

(2) Conversion of the position data

Convert the format of position data and relevant command, because the configuration of the
E/EN/M1/M2 E/EN/M1/M2 series controller’s position data is different from the CRn-500/700 series
controller’s.

Caution
Only programs on the computer can be converted.
Program conversion is only possible for programs on the computer. It is not possible to directly convert a
program on a controller or on a virtual controller with a simulation running. To convert a program on a
controller or on a virtual controller with a simulation running, first use program management to copy it onto the
computer, then convert it there.

7.11.1. Starting program conversion

From the project tree, select the conversion destination project with [Offline] -> [Program], then click the
right mouse button. From the right mouse button menu, click [Program Convert].
The destination is in the program language set for this project.

Figure 7-58 Starting Program Conversion

7-100 7-100
7.11.2. Line number conversion (from MELFA-BASIC IV to MELFA-BASIC V)
Convert the lines No. and relevant command line, because the deal of line No. in MELFA-BASIC IV is different
from MELFA-BASIC V.

For the MELFA-BASIC V, convert as follows.

- The line No. is converted to the step No. (sequential No. which starts from 1).

100 MOV P1 1 MOV P1

110 MVS P2 2 MVS P2
120 MOV P3 3 MOV P3
: :

- The command line using line No. jump is converted to the command line using label jump.
100 MOV P1 1 *LB00001 : MOV P1
110 MVS P2 2 MVS P2
120 GOTO 100 3 GOTO *LB00001
: :

*LB00001 is the label name created automatically by this conversion.

Convert the program according to the following procedure.

(1)

(2)

(3)

(4)
Figure 7-59 Conversion from MELFA-BASIC IV to MELFA-BASIC V

(1) Select the program language of the source and target for conversion.
Start program conversion with the project set with "MELFA-BASIC V"
Choose “MELFA-BASIC IV” for the source and choose “MELFA-BASIC V” for the target.
It is NOT necessary to select the axis of robot.

7-101 7-101
 (2) Select the file as source.
Click the [Select] button of the source, and select the file of MELFA-BASIC IV program.

(3) Input the name of the file to save the converted program into.

(4) After designating the conversion source file and the conversion destination file, click the [Convert]
button or the [Convert & Open] button.
When [Convert] button is clicked, the designated selected file is converted and written in the target file.
When [Convert & Open] button is clicked, the file is converted, written in the target file and opened
through at Program edit tool.

7-102 7-102
7.11.3. Position data conversion (from E/EN/M1/M2 series to CRn-500/700 series)
This function converts the format of position data and relevant command (DJ, MP and PD command of
MOVEMASTER command), because the configuration of the E/EN/M1/M2 series controller’s position data is
different from the CRn-500/700 series controller’s.

Note1: The program conversion converts the position data as well as the commands related to the position
data.
It is not possible to convert commands automatically. Be sure to make grammatical check using this
software before using the program of E/EN/M1/M2 series by the CRn-500/700 series, and change the
commands if necessary.

Note2: The position data of the MOVEMASTER command program for M1/M2 series has the base-coordinate
rotated 90º. When using the program for M1/M2 by the CRn-500/700 series, convert M1/M2 program
into EN program with the E/EN/M1/M2 series support software DOS version, before carrying out the
program conversion.

Note3: In the case of the E/EN/M1/M2 series support software DOS version and E/EN series Robot
programming supporter for Windows, the data can be saved separately such as command sentence
only, position data only or command sentence and position data. In this program conversion, it is
possible to convert the file of command sentence only and the file of position data only to one program.
The other combinations occurs error. (As following case 3 to 7.)

OK
Case 1:
Command
sentence Program Case 3: Case 3:
Command
sentence
+ Program +
conversion Program
Position data Position data
conversion NG
Command sentence only

Case 2: Command sentence only OK

Program
Program Command
conversion Case 4: Case 4:
3:
Position data only sentence
+
Position data Program
conversion NG
Position data only

Case 5: Command
Case 5:
4:
3:
sentence
+
Position data
Program
conversion NG
Command
5:
Case 3:
4:
sentence
+
Position data

Case 6: Command sentence only

Program
conversion NG
Command sentence only

Case 7: Position data only

Program
conversion NG
Position data only

7-103 7-103
Convert the program according to the following procedure.

(1)

(2)

(3)

(4)

(5)
Figure 7-60 Conversion from MELFA-BASIC III to MELFA-BASIC IV

(1) Select the program language of the source and target for conversion.
Start program conversion with a project set for "MELFA-BASIC V" or "MELFA-BASIC IV".
For the source, choose “MELFA-BASIC III” or “MOVEMASTER (CR-116/356)” which is the program
language of the E/EN/M1/M2 series.
If “MELFA-BASIC V” is chosen for the target, the lines No. are also converted in addition to this
conversion.

(2) Select the axis of robot.

Select the correct number of axes, so that the configuration of the E/EN/M1/M2 series controller’s
position data is different depending on the number of axes.

(3) Select the file(s) as source.

Click the [Select] button of the source, and select the file(s) of E/EN/M1/M2 series program.
When selecting the multiple files, click the file while pushing the [Ctrl] key.

(4) This specifies the file to write the converted program into.
Input the name of the file to save the converted program into.

(5) After designating the conversion source file and the conversion destination file, click the [Convert]
button or the [Convert & Open] button.
When [Convert] button is clicked, the designated selected file is converted and written in the target file.
When [Convert & Open] button is clicked, the file is converted, written in the target file and opened
through at Program edit tool.

7-104 7-104
8. Setting Parameters
You can reference and rewrite parameter information set in a robot controller.
You can set parameters with the method of specifying parameter names and setting them or with the method
of making the settings arranged by function.

8.1. Editing from parameter list

You can reference and rewrite individual items of parameter information set in a robot controller by specifying
the name of the parameter.

8.1.1. Starting
This is used in the state with the robot controller connected.
From the project tree, double click [Online] -> [Parameter] -> [Parameter List].

Figure 8-1 Starting the Parameter List

At this time, a confirmation message like the following concerning the parameter list is displayed.

Figure 8-2 Confirmation Message for Parameter List

This window will appear in the following cases.

- When there is no parameter list information in the personal computer.
- When the parameter list used in the robot controller is newer than the parameter list already stored in the
personal computer.

8-105 8-105
 Memo
What is the parameter list?
The parameter list is a list of parameter information comprised of parameter names, explanatory text, etc.
displayed on the parameter list screen. This parameter list can be downloaded from the controller. The
version of the parameter list may vary with the version of the software on the controller. We recommend that you
download the latest parameter list from the controller.

When parameter list reading is specified, the screen for selecting where to read it from is displayed.

Figure 8-3 Parameter List Select Screen

Select either "Read from RC" or "Read from file", set the parameter list to be read, then click the [OK] button.

8-106 8-106
8.1.2. Parameter editing
Double click a parameter displayed in the list or input its name, then click the [Read] button. The specified
parameter information in the robot controller is displayed.

Figure 8-4 Parameter Editing

After you change a parameter, you can rewrite the specified parameter information in the robot controller by
clicking the "Write" button.

You can print the displayed parameter information by clicking the [Print] button.

Caution
Use upper case letters when naming the programs in alphabetic
characters.
Lower case alphabetic characters can be used in this parameter setting.
Use upper case letters when naming the programs in alphabetic characters for the parameters of the base
program (PRGUSR) or slot table (SLT*), etc. All of the program names within the robot controller will be
expressed in upper case letters.
If lower case letters are used, the programs will not be properly recognized.

To put a changed parameter value into effect, switch the robot

controller power Off, then On again.
To validate the rewritten parameter information in the robot controller, the robot controller power must be
turned ON again.

8-107 8-107
8.1.3. Parameter list reading
If no parameter name is displayed on the parameter list screen, you can read the parameter list.
Click the parameter list [Read] button at the top right of the parameter list screen. The parameter list select
screen is displayed.

Figure 8-5 Parameter List Reading

Select the source to read from ("Read from RC" or "Read from file"), then set the parameter list to read and
click the [OK] button.

8.1.4. Finding parameters

You can find a character string in the displayed parameter list. With the "Parameter List" screen active, click
on the menu bar [Parameter] -> [Find]. The character string find screen is displayed.

Figure 8-6 Finding a Character String

Input the character string to search for, then click the [Find] button. Parameters that include the input character
string are displayed.

8-108 8-108
8.2. Robot Controller Operation Modes for Parameter Writing
With CRn-500 series robot controllers, when you write parameters to the robot controller, controller software
version may place restrictions on the operating mode in which you can write. For details, see below.

However, parameters cannot be written while any program with any startup condition other than Always has
been started. In such a case, stop the program, then write the parameters.

Table 8-1 Download Operating Modes for Writing (for CRn-500 series only)
CRn-500 series robot Operating mode
controller TEACH Auto (OP) Auto (Ext)
J1 edition or later ○ ○ ○

H7 edition or earlier ○ × ×
○: Writing possible ×: Writing impossible

8-109 8-109
8.3. Operating Range Parameters
Set the operating range of the robot
Set parameters while connected to the robot controller.
From the project tree, double click the target project [Online] -> [Parameter] -> [Operating Range].
After you change the parameter value, you can rewrite the operating range parameter in the robot controller
by clicking the [Write] button.

Figure 8-7 Motion Limit Parameters

You can reference explanations of displayed parameters by pressing the [Explain] button.

8.4. Jog Parameters

Set the speeds for joint jogging and orthogonal jogging.
Set parameters while connected to the robot controller. From the project tree, double click the target project
[Online] -> [Parameter] -> [Jog].
After you change the parameter value, you can rewrite the jog parameter in the robot controller by clicking the
[Write] button.

Figure 8-8 Jog Parameters

You can reference explanations of displayed parameters by pressing the [Explain] button.

8-110 8-110
8.5. Hand Parameters
Set the type of the hand (single solenoid/double solenoid, etc.) and work holding/non-holding when HOPEN*
(open hand) and HCLOSE* (close hand) are executed.
Set parameters while connected to the robot controller.
From the project tree, double click the target project [Online] -> [Parameter] -> [Hand].
After you change the parameter value, you can rewrite the parameters concerning the hand in the robot
controller by clicking the [Write] button.

Figure 8-9 Hand parameter

You can reference explanations of displayed parameters by pressing the [Explain] button.

8-111 8-111
8.6. Weight and Size Parameters
You can set the conditions for the hand mounted on the robot and the conditions for the work the robot
grasps.
Set parameters while connected to the robot controller.
From the project tree, double click the target project [Online] -> [Parameter] -> [Weight and Size].
After you change the parameter value, you can rewrite the weight and size parameters in the robot controller
by clicking the [Write] button.

Figure 8-10 Weight and Size Parameters

You can reference explanations of displayed parameters by pressing the [Explain] button.

8-112 8-112
8.7. Tool Parameters
Set the standard tool coordinates and standard base coordinates. Set parameters while connected to the
robot controller.
From the project tree, double click the target project [Online] -> [Parameter] -> [Tool].
After you change the parameter value, you can rewrite the tool parameters in the robot controller by clicking
the [Write] button.

Displayed when you are connected to a

controller that supports position repair.

Figure 8-11 Tool

8-113 8-113
8.8. Slot Tables
Slot tables set the operating conditions of each task slot during multi-task operation.
Set parameters while connected to the robot controller.
From the project tree, double click the target project [Online] -> [Parameter] -> [Slot Table].
After you change the parameter value, you can rewrite the operating range parameter in the robot controller
by clicking the [Write] button.

Figure 8-12 Slot Table

Select the task slot number you are changing and click the [Change] button.

Figure 8-13 Slot Table - Change

When the modification window appears, set the program name, operating conditions, startup conditions and
task priority, and then click [Write].

You can reference explanations of displayed parameters by pressing the [Explain] button.

8-114 8-114
8.9. Output Signal Reset Pattern Parameters
These parameters set the operation when resetting the general-purpose output signals such as the CLR
instruction and dedicated input (OUTRESET).
Set parameters while connected to the robot controller.
From the project tree, double click the target project [Online] -> [Parameter] -> [Output Signal Reset Pattern].

Figure 8-14 OUTPUT Signals reset pattern

Set a signal number, and then select one of [OFF]/[ON]/[Hold]. The value of the signal having the specified
number displayed in the list changes. After you changed the parameter value, you can rewrite the output
signal reset parameter in the robot controller by clicking the [Write] button.

Also, selecting a signal group (for example, "32-0") and then clicking the [Select] button changes 32 signals at
once.

Figure 8-15 I/O Reset Pattern Change

You can reference explanations of displayed parameters by pressing the [Explain] button.

8-115 8-115
8.10. Assigning Dedicated Input/Output Signals
Assign signal numbers to functions in order to perform the remote operations to execute and stop robot
programs, and display/operate the execution progress information and servo power supply status, etc.
Set parameters while connected to the robot controller.

8.10.1. General 1 Parameters

From the project tree, double click the target project [Online] -> [Parameter] -> [Assign dedicated input/output
signal] -> [General 1].
After you change the parameter value, you can rewrite the parameters in the robot controller by clicking the
[Write] button.

Figure 8-16 Assign Dedicated Input/Output Signal General 1 Parameters

You can reference explanations of displayed parameters by pressing the [Explain] button.

8.10.2. General 2 parameters

From the project tree, double click the target project [Online] -> [Parameter] -> [Assign dedicated input/output
signal] -> [General 2].
After you change the parameter value, you can rewrite the parameters in the robot controller by clicking the
[Write] button.

Figure 8-17 Assign Dedicated Input/Output Signal General 2 Parameters

You can reference explanations of displayed parameters by pressing the [Explain] button.

8-116 8-116
8.10.3. Data parameters
From the project tree, double click the target project [Online] -> [Parameter] -> [Assign dedicated input/output
signal] -> [Data].
After you change the parameter value, you can rewrite the parameters in the robot controller by clicking the
[Write] button.

Figure 8-18 Assign Dedicated Input/Output Signal Data Parameters

You can reference explanations of displayed parameters by pressing the [Explain] button.

8.10.4. Jog parameters

From the project tree, double click the target project [Online] -> [Parameter] -> [Assign dedicated input/output
signal] -> [Jog].
After you change the parameter value, you can rewrite the parameters in the robot controller by clicking the
[Write] button.

Figure 8-19 Assign Dedicated Input/Output Signal Jog Parameters

You can reference explanations of displayed parameters by pressing the [Explain] button.

JOGNER(JOG command INPUT signal, During JOG OUTPUT signal) can be used with Version J2 or later of
the CRn-500 series controller, or CRn-700 series controller

8-117 8-117
8.10.5. Hand parameters
From the project tree, double click the target project [Online] -> [Parameter] -> [Assign dedicated input/output
signal] -> [Hand].
After you change the parameter value, you can rewrite the parameters in the robot controller by clicking the
[Write] button.

Figure 8-20 Assign Dedicated Input/Output Signal Hand Parameters

You can reference explanations of displayed parameters by pressing the [Explain] button.

8.10.6. Warm-up operation parameters

The warm-up operation parameters can be set when you are connected to a CRn-500 series robot controller
ofJ8 edition or later or a CRn-700 series robot controller.
From the project tree, double click the target project [Online] -> [Parameter] -> [Assign dedicated input/output
signal] -> [Warm up].
After you change the parameter value, you can rewrite the parameters in the robot controller by clicking the
[Write] button.

Figure 8-21 Assign Dedicated Input/Output Signal Warm-Up Operation Parameters

You can reference explanations of displayed parameters by pressing the [Explain] button.

8-118 8-118
8.10.7. Slot start (each slots) parameters
From the project tree, double click the target project [Online] -> [Parameter] -> [Assign dedicated input/output
signal] -> [Start Slot].
After you change the parameter value, you can rewrite the parameters in the robot controller by clicking the
[Write] button.

Figure 8-22 Assign Dedicated Input/Output Signal Slot Start Parameters

You can reference explanations of displayed parameters by pressing the [Explain] button.

8.10.8. Slot stop (each slots) parameters

From the project tree, double click the target project [Online] -> [Parameter] -> [Assign dedicated input/output
signal] -> [Stop Slot].
After you change the parameter value, you can rewrite the parameters in the robot controller by clicking the
[Write] button.

Figure 8-23 Assign Dedicated Input/Output Signal Slot Stop Parameters

You can reference explanations of displayed parameters by pressing the [Explain] button.

8-119 8-119
8.10.9. Servo On/Off (each robot) parameter
From the project tree, double click the target project [Online] -> [Parameter] -> [Assign dedicated input/output
signal] -> [Servo On/Off].
After you change the parameter value, you can rewrite the parameters in the robot controller by clicking the
[Write] button.

Figure 8-24 Assign Dedicated Input/Output Signal Servo Parameters

You can reference explanations of displayed parameters by pressing the [Explain] button.

8.10.10. Machine lock (each robot) parameters

From the project tree, double click the target project [Online] -> [Parameter] -> [Assign dedicated input/output
signal] -> [Machine lock].
After you change the parameter value, you can rewrite the parameters in the robot controller by clicking the
[Write] button.

Figure 8-25 Assign Dedicated Input/Output Signal Machine Lock Parameters

You can reference explanations of displayed parameters by pressing the [Explain] button.

8-120 8-120
8.11. RS-232 Setup Parameters
These parameters set up the communication environment of the RS-232 interface of the robot controller.
Set parameters while connected to the robot controller.
From the project tree, double click the target project [Online] -> [Parameter] -> [Communication].
After you change the parameter value, you can rewrite the parameters in the robot controller by clicking the
[Write] button.

Figure 8-26 RS-232

You can reference explanations of displayed parameters by pressing the [Explain] button.

8.12. Zone Parameters

You can specify the region (cuboid) defined with two points in the robot XYZ coordinates and set the behavior
for when the robot enters this region. You can set up to 8 zones.

Set parameters while connected to the robot controller.

From the project tree, double click the target project [Online] -> [Parameter] -> [Zone].
After you change the parameter value, you can rewrite the parameters in the robot controller by clicking the
[Write] button.

Figure 8-27 Zone Parameters

You can reference explanations of displayed parameters by pressing the [Explain] button.

8-121 8-121
8.13. Free Plane Limit Parameters
You can set the overrun limit for using the robot on a free plane.
Set parameters while connected to the robot controller.
From the project tree, double click the target project [Online] -> [Parameter] -> [Free Plane Limit].
After you change the parameter value, you can rewrite the parameters in the robot controller by clicking the
[Write] button.

Figure 8-28 Free plane limit parameter

You can reference explanations of displayed parameters by pressing the [Explain] button.

8.14. Escape Point Parameters

Set the position of the escape point.
Set parameters while connected to the robot controller.
From the project tree, double click the target project [Online] -> [Parameter] -> [Escape Point].
After you change the parameter value, you can rewrite the parameters in the robot controller by clicking the
[Write] button.

Figure 8-29 Home Position Parameters

You can reference explanations of displayed parameters by pressing the [Explain] button.

8-122 8-122
8.15. Robot Program Language Parameters
You can set the robot program language used in a robot controller (MELFA-BASIC V/MELFA-BASIC
IV/Movemaster commands). From the project tree, double click the target project [Online] -> [Parameter] ->
[Robot Language].
After you change the parameter value, you can rewrite the parameters in the robot controller by clicking the
[Write] button.

Figure 8-30 Program Language Parameters

You can reference explanations of displayed parameters by pressing the [Explain] button.

For the usable robot program languages, see "Table 6-1 Robot Program Languages for Each Controller".

Caution
About MELFA-BASIC V
MELFA-BASIC V. can only be used with CRn-700 series robot controllers.

About Movemaster commands

The Movemaster commands are restricted by the robot models that can be used. For details on whether you
can use Movemaster commands with your robot, refer to its standard specifications.

8-123 8-123
8.16. Additional Axis Parameters
You can set information related to addition axes of robots.
Set parameters while connected to the robot controller.
From the project tree, double click the target project [Online] -> [Parameter] -> [Additional Axis].
After you change the parameter value, you can rewrite the parameters in the robot controller by clicking the
[Write] button.

Figure 8-31 Additional Axis Parameter List

Motion Limit parameter screen starts with the [Motion Limit] button.
You can reference explanations of displayed parameters by pressing the [Explain] button.
You can read Additional Axis data saved in the file by pressing the [Read from file] button.
You can save Additional Axis parameter to the file by pressing the [Save to file] button.
But Motion Limit parameter is not included in the file saved by pressing the [Save to file] button.
([Moton Limit] button, [Read from file] button, and [Save to file] button correspond with RT ToolBox2 Ver.1.1 or
later.)

Select the additional axis information to be edited and double click. The screen for setting information for the
additional axis is displayed.

Figure 8-32 Additional Axis Parameter Setting

8-124 8-124
8.17. Collision Detection Parameters
You can set information related to the robot's collision detection functions.
Set parameters while connected to the robot controller.
From the project tree, double click the target project [Online] -> [Parameter] -> [Collision Detection].
After you change the parameter value, you can rewrite the parameters in the robot controller by clicking the
[Write] button.

Figure 8-33 Collision Detection Parameters

You can reference explanations of displayed parameters by pressing the [Explain] button.

8-125 8-125
8.18. Warm-Up Operation Parameters
You can set information related to the robot's warm-up function.
Set parameters while connected to the robot controller.
From the project tree, double click the target project [Online] -> [Parameter] -> [Warm-Up].
After you change the parameter value, you can rewrite the parameters in the robot controller by clicking the
[Write] button.

Figure 8-34 Warm-Up Operation Parameters

You can reference explanations of displayed parameters by pressing the [Explain] button.

8-126 8-126
8.19. Movement Parameters
You can set information related to the optimum acceleration/deceleration for robot operation and set
compliance errors.
The information that can be set concerning movement parameters depends on the robot controller
connected.

CRn-700 series CRn-500 series

Maximum acceleration/deceleration J2 edition or later
correction ratio
Compliance error function settings H6 edition or later
Can be used with all versions
Optimum acceleration/deceleration G1 edition or later
setting
Direction of gravity H4 edition or later

Set parameters while connected to the robot controller.

From the project tree, double click [Online] -> [Parameter] -> [Movement Parameters].
After you change the parameter value, you can rewrite the parameters in the robot controller by clicking the
[Write] button.

Figure 8-35 Movement Parameters

You can reference explanations of displayed parameters by pressing the [Explain] button.

8-127 8-127
8.20. Program Parameters
You can set parameters related to robot programs.
Set parameters while connected to the robot controller.
From the project tree, double click the target project [Online] -> [Parameter] -> [Program Parameters].
After you change the parameter value, you can rewrite the parameters in the robot controller by clicking the
[Write] button.

Figure 8-36 Program Parameters

You can reference explanations of displayed parameters by pressing the [Explain] button.

8-128 8-128
8.21. User Error Parameters
You can set the message, cause, and recovery method for user errors set with a program.
Set parameters while connected to the robot controller.
From the project tree, double click the target project [Online] -> [Parameter] -> [User Error].

Figure 8-37 User Error Parameters

Double click the error number from the list. The "User Error" edit screen is displayed.

Double click

Figure 8-38 User Error Edit

Input the error number, error message, cause, and recovery method, then click the [OK] button. The user
errors input to the list are displayed.
At this time, input an error number from "9000" – "9200".
After you confirm the parameter value, you can rewrite the parameters in the robot controller by clicking the
[Write] button.
Please note that the list display is not sorted by error number.

You can reference explanations of displayed parameters by pressing the [Explain] button.

8-129 8-129
8.22. Ethernet Settings
You can set robot controller Ethernet information.
Set parameters while connected to the robot controller.
From the project tree, double click the target project [Online] -> [Parameter] -> [Ethernet Settings].
After you change the parameter value, you can rewrite the parameters in the robot controller by clicking the
[Write] button.

Figure 8-39 Ethernet Settings

You can reference explanations of displayed parameters by pressing the [Explain] button.

Select the device to edit and double click. A screen is displayed for setting a variety of device information.

Figure 8-40 Device Setting

If you check the [Change the Parameter to connect Vision] checkbox, the items from "Port" downward take on
the values for a network vision sensor.

Caution
Using a CRn-500 series robot controller
When using Ethernet with a CRn-500 series robot controller, the "Ethernet interface" option is required.

8-130 8-130
8.23. Multiple CPU Settings
You can set the parameters related to the Multiple CPU to use the CRnQ-700 series robot controller.
These parameters can be set when you are connected to CRnQ-700 series robot controller.
This function is available from RT ToolBox2 Ver.1.1 or later.

Set parameters while connected to the robot controller.

From the project tree, double click the target project [Online] → [Parameter] → [Multiple CPU setting].
After you change the parameter value, you can rewrite the parameters in the robot controller by clicking the
[Write] button.

Figure 8-41 Multiple CPU Setting

You can reference explanations of displayed parameters by pressing the [Explain] button.
You can check the number of points input and range of total by pressing the [Check] button.

Please refer to the manual of Universal model QCPU (QCPU User’s Manual (Multiple CPU System)) for details
of Multiple CPU setting.

8-131 8-131
8.24. Parameter printing
You can print the parameter values held in a robot controller.

Display the parameters to print, then click on the menu bar [Workspace] -> [Print]. The print screen is
displayed, so check the printer, then click the [OK] button. Printing starts.
Also, you can click on the menu bar [Workspace] -> [Print Preview] to look at the print image.

Figure 8-42 Parameter Printing

Caution
Install the printer beforehand.
Install the printer beforehand. For details on the installation method for the printer, refer to the operations
manuals for your printer and computer.

8-132 8-132
9. Status Monitoring
You can set various information in the currently connected robot controllers to be constantly displayed.
The monitor functions are roughly divided into the following three.

1. Robot movement monitor .......... Items related to robot movement are monitored.
2. Operation monitor ....................... Items related to the robot's operation are monitored.
3. Servo monitor ............................. The robot's servo system information is monitored.

Table 9-1 Summary of Each Monitor

Monitor name Explanation
Slot run state The operation state of each slot can be confirmed.
Program monitor The program execution line set for each slot, the contents of the
Robot movement

variable used in the program, and the robot current position, etc., can
be confirmed.
monitor

Movement State The current position information and hand open/close state of each
connected mechanism can be confirmed.
Error The currently occurring error can be confirmed.
The history of the errors that have occurred can be confirmed.
Robot status You can display the robot and its movements in 3D to check them.
General signals You can check the statuses of signals input to the robot controller
from outside equipment and signals output from the robot controller
to outside equipment.
Pseudo-input and forced output of signals are also possible.
Signal monitor

Named signal The status can be checked by naming the status of the dedicated I/O
signal that has been set in the robot controller, as well as each bit or
within the range of 32 bits of the general-purpose signal.
The signals are set via parameter setting (maintenance tool).
Stop signal The stop signal input into the robot controller can be confirmed.
Registers (CC-Link) You can monitor the input registers and output registers for the
CC-Link functions.
Pseudo-input and forced output of registers are also possible.

Operating time The robot operation time (power ON, etc.) can be confirmed.
Operating
monitor

Production The operating time of the program in the robot controller and the No.
information of program cycles can be confirmed.

9-133 9-133
9.1. Robot Operation Monitoring

9.1.1. Slot operation statusmonitaring

The state of the slots in the robot controller can be monitored.
From the project tree, double click the target project [Online] -> [Monitor] -> [Movement Monitor] -> [Slot
Status].

Figure 9-1 Slot Run Status

The No. of displayed slots is determined with the parameters.

9-134 9-134
9.1.2. Program monitoring
Information on the running program can be monitored.
From the project tree, click the target project [Online] -> [Monitor] -> [Movement Monitor] -> [Program
Monitor], then double click the "Task slot" to monitor.

(2) Program

(1) Program information

(3) Variable monitor

(4) Add

(5) Select (6) Delete (7) Change (8) Load (9) Save (10) View
Figure 9-2 Program monitor

(1) Program information

You can check the currently selected program name and operation status and the name of the currently
connected robot model.

(2) Program
The currently selected program is displayed. The currently executing line is displayed inverted.

(3) Variable monitor:

You can check the names of variables being used in the selected program. You can select the variables to
monitor with the buttons displayed at the bottom of the screen.

9-135 9-135
(4) Adding variables
This adds more variables to monitor.

A dropdown list
is displayed.

Figure 9-3 Add Variables

Input the variable name or select it from the dropdown menu, set the variable type, then click the [OK]
button.
The variables being used in the program are displayed in a dropdown list. When you select variables from
the dropdown list, the variable type is automatically selected.

(5) Selecting variables

You can batch select variables to monitor from the variable list used in the program.

Figure 9-4 Variable Selection

The "variables not to display" are displayed in the list on the left side and the "variables to display" are
displayed in the list on the right side. From the "variables not to display" list, select the variables to monitor,
then click the [Add->] button. The selected variables are added to the "variables to display" list. If you select
variables from the "variables to display" list, then click the [<-Delete] button, the selected variables are
deleted from the "variables to display" list and added to the "variables not to display" list.
When you click the [OK] button, the variables registered in the "variables to display" list are displayed on
the variables monitor and you can reference their values.

(6) Deleting variables

This deletes variables registered on the variables monitor from the monitor list. This operation does not
delete the variables themselves from the program.

9-136 9-136
(7) Changing variables
You can change the values of variables registered on the variables monitor.
On the variables monitor, select the variables to change the values, then click the [Change] button.

Figure 9-5 Changing Variable Values

After confirming the variable name, input the value of the variable, then click the [OK] button.

Caution
Be careful when changing the value of a variable.
When you change the value of a variable, the operation target position of the robot may change and result in
a collision. This is particularly dangerous during robot operation, so check carefully before changing the value of
a parameter.

(8) Load
You can load variables to be monitored on the variables monitor from a file.
When you click the [Load] button, you can load variable names and variable types and add them as
variables to be monitored.

(9) Save
You can save as a file a list of the variables being monitored on the variables monitor.
When you click the [Save] button, you can save the names, types, and values of the variables currently
being monitored into a file. This file is saved in text format.

9-137 9-137
(10) View
You can switch the values of the variables displayed on the variables monitor between hexadecimal
display and decimal display.
The variables that can be displayed in hexadecimal, see below.

Table 9-2 16Variables that can be displayed in Hexadecimal

The displayed variable can be switched to the hexadecimal number /
Integer
the decimal number.
When it is 0 below the decimal point, it is possible to switch to the
Float hexadecimal number / the decimal number.
However, the value is the one within the range of -9999999 - 9999999.
String The hexadecimal number is not displayed.
Location The hexadecimal number is not displayed.

As for the value displayed by the hexadecimal number, “&H” is added to the head of the value.

9.1.3. Movement status

You can check the robot current position, destination position, hand open/close status, etc.
* Destination position corresponds with RT ToolBox2 Ver1.1 or later.

From the project tree, double click the target project [Online] -> [Monitor] -> [Movement Monitor] ->
[Movement Status].

Figure 9-6 Movement Status

9-138 9-138
9.1.4. Errors
The errors currently occurring in the robot controller are displayed.

9.1.4.1. Referencing the current error

From the project tree, double click the target project [Online] -> [Monitor] -> [Movement Monitor] -> [Error].

Figure 9-7 Error Screen

[Details] You can check details (cause and recovery method) on errors.
[History] You can reference the history of errors that have occurred.

9.1.4.2. Details
You can check details (cause and recovery method) on errors. On the error screen, select an error, then
either click the "Details" button or double click the error.

Click or double click the [Details] button.

Figure 9-8 Error Details Screen

9-139 9-139
9.1.4.3. History information
The history of errors that have occurred in the past can be referred to.
You can check the error history in the robot controller for each error level (high level, low level, caution).
You can also save the error history into a file.

Click the [History] button. After selecting the level to reference, click the [OK] button.

Figure 9-9 History Information Error Level Setting

(1)Display
switching

(2) Details (3) Save (4) Refresh

Figure 9-10 Error History

This display is not constantly displayed. To refresh information, click the [Refresh] button.

(1) Display switching

This redisplays the displayed error history for each error level.

(2) Details
After selecting a displayed error, you can check the cause and recovery method for the error by clicking this
button.
You can also check details by double checking a displayed error.

(3) Save
This saves the displayed error history information into a file. For the saved error history information,
select "From history file" with "Figure 9-9 ". Refer to "Figure 9-11 " on the screen, after you selected
“From history file”.
The error file is saved in text format. You can also print it with Notepad or other general text editors.

(4) Refresh
This refreshes the displayed information. The error history screen is not a self refreshing display monitor,
so even if an error occurs after the error history screen is displayed, it is not automatically added to the
display. Click the [Refresh] button.

9-140 9-140
 Figure 9-11 Error History Information Read from File

9.1.5. Robot status

You can display the robot and its movements in 3D to check them.
From the project tree, either double click the target project [Online] -> [<Robot model name>] or select [3D
Monitor] with the mouse right button menu. The robot 3D display screen is displayed. If the "display travel table
setting" is made for the project, the travel table is also displayed.

Either double click the robot model name or

select [3D Monitor] with the mouse right
button menu.

Figure 9-12 Starting Robot View

You can change the robot view perspective with mouse operation.

Table 9-3 Robot View Perspective Change Operation

Perspective to change Graphic mouse operation
Perspective rotation While clicking the left button, move left/right→
Rotation around Z axis
Move up/down→Rotation around X axis
Move left/right while clicking the left + right buttons→
Rotation around Y axis
Perspective movement Move up/down/left/right while clicking the right button
Graphic Move up/down/left/right while clicking pressing [Shift] key and
enlargement/reduction clicking the left button

9-141 9-141
9.2. Signal Monitoring

9.2.1. General signal

You can check the statuses of signals input to the robot controller from outside equipment and signals
output from the robot controller to outside equipment.
From the project tree, double click the target project [Online] -> [Monitor] -> [Signal Monitor] -> [General
Signals].
The upper level displays the status of input signals and the lower level displays the status of output signals.
A continuous range of signals to display can be set freely with [Monitor Settings].
Pseudo-input and forced output of registers are also possible.

Figure 9-13 General Signals

9.2.1.1. Monitor settings

For the displayed signals, the continuous range can be set freely.
Set the lead numbers for the input signal number and output signal numbers to display, set their respective
display ranges on the line, then click the [OK] button.

Figure 9-14 General Signal Monitor Settings

9-142 9-142
9.2.1.2. Pseudo-input
Pseudo-input means signals that are input to the robot controller from the computer, not from outside
equipment.
Click the [Pseudo-Input] button. A screen for inputting pseudo signals is displayed.

Caution
While the robot controller is in pseudo-input mode, signal input from
outside devices is not accepted.
To use pseudo-input, put the robot controller into pseudo-input mode. While the robot controller is in
pseudo-input mode, the robot controller does not accept signal input from outside devices.
Click the [Pseudo-Input] button. The confirmation message below is displayed before the robot controller
goes into pseudo-input mode.

To release a robot controller from pseudo-input mode, switch the

power for the robot controller Off, then On again.

Figure 9-15 Pseudo-Input

① First, read the signals you want to pseudo input.

You can set 32 signals at the same time. Input the head number for the signals you want to read, then click
the [Set] button.
② The input statuses of the 32 signals starting from the specified head signal number are displayed. Set the
pseudo-input status, then click the [Bit Pseudo-INPUT] button.
③ You can specify the hexadecimal values and make pseudo input for the 32 signals starting from the head
signal number.
Input the values in hexadecimal, then click the [Port Pseudo-INPUT] button.

9-143 9-143
9.2.1.3. Forced output
You can force signals to outside equipment from robot controllers.
Click the [Forced Output] button. A screen for forcibly outputting signals is displayed.

Figure 9-16 Forced Signal Output

① First, read the signals you want to forcibly output.

You can output 32 signals at the same time. Input the head number for the signals you want to read, then
click the [Set] button.
② The output statuses of the 32 signals started from the specified head signal number are displayed. Set the
output status, then click the [Bit Forced OUTPUT] button.
③ You can specify the hexadecimal value and force output for the 32 signals starting from the head signal
number.
Input the values in hexadecimal, then click [Port Forced OUTPUT] button.

Caution
Forced signal output
- Signal numbers assigned (used) as dedicated output signals cannot be forcibly output.
- Forced output is possible if the robot controller mode is either [AUTOMATIC] or [MANUAL] (for a CRn-500
series robot controller, [TEACH], [AUTO (OP)], OR [AUTO (EXT.)]), but if even one program is running, forced
output is not possible. (Except an ALWAYS program)

9-144 9-144
9.2.2. Named signals
You can give names to general input/output signals and check their statuses.
With "Named signals", you can check the status of dedicated input/output signals and named general
input/output signals. When starting up, you can load a definition file for named signals in the robot controller.
From the project tree, double click the target project [Online] -> [Monitor] -> [Signal Monitor] -> [Named
Signals].

Figure 9-17 Named Signal

[Add] : This registers a new general input/output signal name.

[Edit] : This changes the setting for an existing general input/output signal selected in
the list.
[Delete] : This deletes a signal selected in the list.
[Load] : This loads a file defining saved named signals in the robot controller and in the
computer.
[Save] : This saves the information on the set named signals to the robot controller or
computer.
[Delete signal : This deletes the named signal information in the robot controller.
file in robot]

9.2.2.1. Adding new named signal or revising one

To add a new named signal, click the [Add] button. To revise one, select the signal to be revised from the list
and click the [Edit] button.

Figure 9-18 Signal Name Editing

Input the general signal numbers and names, select the signal type and display method, then when adding a
new named signal, click the [Add] button. The set signal is added to the list.
The [Add] and [Change] buttons do not close the "Signal name edit" screen, so you can continue to add more
signals.

9-145 9-145
9.2.2.2. Deleting a named signal
Select the signals to delete from the list. You can select multiple signals by clicking them while holding down
the [Ctrl] key or the [Shift] key on the keyboard.
However, dedicated input/output signals can not be deleted.
Also, you can not delete input signals and output signals at the same time. Finally, delete the select signals
in the list with a mouse click.

9.2.2.3. Named signal definition information reading

When you click the [Load] button, a message asking you to confirm that you want to delete a registered
general input/output signal is displayed.
This message asks you to confirm that you want to clear the current general input/output signal display.

Figure 9-19 Deletion Confirmation Message for Registered General Input/Output Signal

If you select [Yes] on this confirmation screen, the "Select locate" screen asking you to select the load source
is displayed.

Figure 9-20 Device Selection

Select the device to load from, then click the [OK] button.
If you select the local device, the screen for selecting a file in the computer is displayed.
If you select the robot controller, the named signal definition file is loaded from the robot controller.

9.2.2.4. Saving definition information for named signals to a controller

When you click the [Save] button, the "Select locate" screen asking you to select the save destination is
displayed.

Figure 9-21 Device Selection

Select the device to save to, then click the [OK] button.
If you select the local device, the screen for selecting a file in the computer is displayed.
If you select the robot controller, the named signal definition file is saved to the robot controller.

9-146 9-146
9.2.3. Stop signal
You can reference the statuses of stop signals (stop/not stop) input to the robot controller.
From the project tree, double click the target project [Online] -> [Monitor] -> [Signal Monitor] -> [Stop Signals].

Figure 9-22 Stop Signal

9-147 9-147
9.2.4. Register (CC-Link) monitoring

Caution
This can only be used if the CC-Link option card is mounted in the
robot controller.
This function can only be used with a CRn-500 series or CRnD-700 series robot controller with the CC-Link
option card mounted. Also, this function can not be used with CRnQ-700 series robot controllers.

You can check the statuses of registers input to the robot controller from outside equipment and registers
output from the robot controller to outside equipment.
From the project tree, double click the target project [Online] -> [Monitor] -> [Signal Monitor] -> [Register
(CC-Link)].
The left side of the screen displays the status of input registers and the right side displays the status of
output registers.
A continuous range of registers to display can be set freely with [Monitor Settings].
Pseudo-input and forced output of registers are also possible.

Figure 9-23 Registers (CC-Link)

9.2.4.1. Monitor settings

A continuous range of registers to display can be set freely.
Set the lead numbers for the input register number and output register numbers to display, set their respective
display ranges on the line, then click the [OK] button.

Figure 9-24 Registers (CC-Link) Monitor Settings

9-148 9-148
9.2.4.2. Pseudo-input monitoring:Pseudo-input
Pseudo-input means registers that are input to the robot controller from the computer, not from outside
equipment.
Click the [Pseudo-Input] button. A screen for inputting pseudo signals is displayed.

Caution
While the robot controller is in pseudo-input mode, register input
from outside devices is not accepted.
To use pseudo-input, put the robot controller into pseudo-input mode. While the robot controller is in
pseudo-input mode, the robot controller does not accept register input from outside devices.
Click the [Pseudo-Input] button. The confirmation message below is displayed before the robot controller
goes into pseudo-input mode.

To release a robot controller from pseudo-input mode, switch the

power for the robot controller Off, then On again.

Figure 9-25 Pseudo-Input

① Read the signal you want to pseudo input.

You can set 16 registers at the same time. Input the head number for the signals you want to read, then
click the [Set] button. The input statuses of the 16 registers starting from the specified head signal
number are displayed.
② Set the pseudo-input status, then click the [Input] button. The set register values are pseudo input to the
robot controller.
③ You can display and make pseudo input in hexadecimal for register values. If you have selected [Hex],
input values as hexadecimals.

When you click the [Refresh] button, the latest register information is displayed.

9-149 9-149
9.2.4.3. Forced Output

You can forcibly output register values to outside equipment from robot controllers.
Click the [Forced Output] button. A screen for forcibly outputting registers is displayed.

Figure 9-26 Forced Signal Output

① First, read the registers you want to forcibly output.

You can output 16 registers at the same time. Input the head number for the registers you want to forcibly
output, then click the [Set] button. The output statuses of the 16 registers starting from the specified head
register number are displayed.
② Set the output status, then click the [OUTPUT] button. The specified register values are forcibly output
from the robot controller.
③ You can also display and forcibly output register values in hexadecimal. If you have selected [Hex], input
values as hexadecimals.

When you click the [Refresh] button, the latest register information is displayed.

Caution
Forced register output
Forced output is possible if the robot controller mode is either [AUTOMATIC] or [MANUAL] (for a CRn-500
series robot controller, [TEACH], [AUTO (OP)], OR [AUTO (EXT.)]), but if even one program is running, forced
output is not possible. (Except an ALWAYS program)

9-150 9-150
9.3. Production Condition Monitoring

9.3.1. Operation hours

You can check the robot work time, battery usage time, etc.
From the project tree, double click the target project [Online] → [Monitor] → [Operation Monitor] → [Operation
Time].

Figure 9-27 Operating Hours

You can initialize the battery remaining time with [Maintenance] → [Initialize]. For details on operation methods,
see "10.2.4 Initializing the battery remaining time".

9.3.2. Production information

You can check the latest tact time, run time, cycle count, and average tact time for each program in the robot
controller. The latest tact time, run time, and average tact time can be measured up to 1193 hours (about 49
days).
From the project tree, double click the target project [Online] → [Monitor] → [Operation Monitor] →
[Production Information].

Figure 9-28 Production Information

The production information is not constantly updated. Click the [Refresh] button as necessary.

9-151 9-151
10. Maintenance
With maintenance, you can maintain the robot in various ways, including setting origin data and initializing
various information.

10.1. Setting Origin Data

You can save robot origin data to a file, edit it, and transfer it to a robot controller.

Set origin data while connected to the robot controller.

From the project tree, double click the target project [Online] → [Maintenance] → [Origin Data].

Figure 10-1 Starting up the Origin Data Setting Screen

Caution
About controller modes in which origin data can be read/written
The controller modes (TEACH/AUTO (Op.)/AUTO (Ext.)) in which origin data can be read/written depend on
the CRn-500 series robot controller version. For details, see "Table 10-1 Origin Data Reading Robot Control
Operation Mode" and "Table 10-2 Origin Data Writing Robot Control Operation Mode".

Figure 10-2 Origin Data Screen

* About robot controller run modes when origin data is read/written

With CRn-500 series robot controllers, when robot origin data is read/written using this software, there are
restrictions on the controller run mode according to the robot controller software version.
Reference the table below.

10-152 10-152
(1) Reading
Table 10-1 Origin Data Reading Robot Control Operation Mode

CRn-500 series robot Operating mode

controller TEACH Auto (OP) Auto (Ext)
J1 edition or later ○ ○ ○

H7 edition or earlier × × ○
○: Reading possible, ×: Reading not possible

(2) Writing
Table 10-2 Origin Data Writing Robot Control Operation Mode

CRn-500 series robot Operating mode

controller TEACH Auto (OP) Auto (Ext)
J1 edition or later ○ ○ ○

G9 edition – H7 edition ○ × ○

G8 edition or earlier ○ × ×
○: Writing possible, ×: Writing not possible

10-153 10-153
10.1.1. Origin data input technique
You can save robot origin data to a file, edit it, and transfer it to a robot controller.
Click the origin data screen "origin data input technique" to display the screen.

Figure 10-3 Origin Data Input Technique Screen

[Write] : Writes the origin data displayed on the screen to the robot controller.
[Save to file] : The displayed origin data can be saved to a file.
[Read from a file] : Stored origin data can be read from a file and displayed on the screen.
[Refresh] : Reads the origin data from a robot controller and displays the latest
status.

Caution
Input the correct values for the J7 and J8 origin data.
For the J1-J6 axis origin data, the compatibility of values in the robot controller are checked but the J7 and
J8 origin data are not checked. Always input correct values.
The J7 and J8 axis origin data is only displayed when there is a supported additional axis.

Memo
About DJNT (origin error) parameters
DJNT shows the origin position error. When revising the origin position using the position repair tool, the
value is set in DJNT. (When not revising the origin position using the position repair tool, all the elements
become 0. However, for RV-4A, the values are entered beforehand.)
DJNT is not released to general customers, so the values can not be directly changed.

About DJNT parameter display

Sometimes DJNT parameters are not displayed for certain robots (for example, robots that do not support
the position repair function).

10-154 10-154
10.1.2. Mechanical stopper technique
This uses the robot mechanical stoppers to set the robot origin.
Click the origin data screen [Mechanical stopper] button to display the screen.

After moving the robot to a mechanical stopper origin position, select the axis to set the origin for with the
checkbox, then click the [Set origin] button.
"Last" displays the origin setting technique used the previous time. For some robot controller software versions,
this is sometimes not displayed.

Figure 10-4 Origin Setting (Mechanical Stopper) Screen

10.1.3. Tool technique

This uses the origin setting tool to set the robot origin.
Click the origin data screen [Tool] button to display the screen.

After moving the robot to the tool origin position, select the axis to set the origin for with the checkbox, then
click the [Set origin] button.
"Last" displays the origin setting technique used the previous time. For some robot controller software
versions, this is sometimes not displayed.

Figure 10-5 Origin Setting (Tool Technique)

10-155 10-155
10.1.4. ABS origin technique
This uses the robot's ABS origin position robot to set the robot origin.
Click the origin data screen [ABS] button to display the screen.

After moving the robot to the ABS origin position, select the axis to set the origin for with the checkbox, then
click the [Set origin] button.
"Last" displays the origin setting technique used the previous time. For some robot controller software
versions, this is sometimes not displayed.

Figure 10-6 Origin Setting (ABS Origin Technique) Screen

10.1.5. User Origin Technique

This uses the robot user origin to set the robot origin.
Click the origin data screen [User origin method] button to display the screen.

After moving the robot to the user origin position, use the checkbox to select the axis to set the origin of, then
click the [Set origin] button.
"Last" displays the origin setting technique used the previous time. For some robot controller software
versions, this is sometimes not displayed.

Figure 10-7 Origin Setting (User Origin Technique) Screen

10-156 10-156
10.1.6. Origin Parameter Backup
You can back up the parameters that make up the origin data. Also, you can transfer the backed-up data to a
robot controller.
Click the origin data screen [Backup origin parameter] button to display the screen.

Figure 10-8 Robot Origin Parameter Backup Screen

[Save to file] : This saves origin parameters read from a robot controller (displayed
parameters) to a file.
[Select file for writing : Transfer origin parameters stored in a file to a robot controller.
to robot] When transferring to a CRn-500 series robot controller with edition H7 or
earlier, set "Teach" mode.

10-157 10-157
10.2. Initialization
This initializes information in a robot controller.
Here, you can initialize the following information in a robot controller.
(1) Set the robot controller clock
(2) Initialize all programs in the robot controller
(3) Initialize the remaining battery time in the robot controller
(4) Check the serial number in the robot controller and set the serial number for the connected robot
(Serial number checking and setting can only be used with CRn-700 series robot controllers.)

10.2.1. Starting
Use the initialization function while connected to the robot controller.
From the project tree, double click the target project [Maintenance] → [Initialize].

Figure 10-9 Starting Initialization Screen

10.2.2. Setting the time in the robot controller

You can set the robot controller clock.
On the initialization screen, click the [Set time] button.

Figure 10-10 Time Setting Screen

Set the new date and time, then click the [OK] button.
You can set the current date and time from your computer by clicking the [Get PC time] button.

10-158 10-158
10.2.3. Deletion of all robot programs

This deletes all the programs in the robot controller.

On the initialization screen, click the program group [Initialize] button.
A confirmation screen is displayed, so input "Yes", then click the [OK] button.

Figure 10-11 Confirmation Screen for Program File Initialization

10.2.4. Initializing the battery remaining time

This initializes the remaining battery time in the robot controller.

On the initialization screen, click the remaining battery time [Initialize] button.
A confirmation screen is displayed, so input "Yes", then click the [OK] button.

Figure 10-12 Confirmation Screen for Battery Time Remaining

Caution
Do not initialize unless the battery has been replaced.
Be careful. If you initialize the remaining battery time other than when the battery is replaced, it becomes
impossible to reference a correct reading for the remaining battery time.

10.2.5. Serial number

This checks the serial number in the robot controller and sets the serial number for the connected robot
On the initialization screen, click the serial number group [Set] button.

This function can only be used with CRn-700 series robot controllers.
The first time you start up a CRn-700 robot controller after purchase, the C0150 warning (robot main unit
serial number not set) is generated. On this screen, set the robot main unit serial number.

Figure 10-13 Serial Number Input Screen

10-159 10-159
10.3. Maintenance Forecasting
With "Maintenance forecasting", you can reference the parts replacement timing (greasing and battery and belt
replacement) from operation data collected up till now in the robot controller.

Caution
The results of calculations in Maintenance Forecast merely show
reference values.
Please execute the daily inspection and the periodic inspection to
prevent the breakdown beforehand, and to secure safety.

10.3.1. Specifications
With CRn-500 series robot controllers, there are restrictions on the maintenance forecast functions according
to robot models and versions supported. The robot controller software versions and models supported by the
maintenance forecast function are as follows.

Table 10-3 Supported models and software versions

CRn-700 series CRn-500 series
No. Robot
Robot controller Robot controller
RV-6S series
1 Ver. J2 or later
RV-12S series
RV-3S series The supported
2 Ver. K1 or later
RV-3SJ series models are not
RH-6SH series restricted
3 RH-12SH series Ver. K4 or later
RH-18SH series

10.3.2. Starting
Use the maintenance forecast function while connected to the robot controller.
From the project tree, double click the target project [Online] → [Maintenance] → [Maintenance Forecast].

Figure 10-14 Starting Maintenance Forecasting

10-160 10-160
10.3.3. Forecasting
You can reference the "time until battery replacement", "time until regreasing, and time until belt
replacement".

(4) Display units

(1) Battery

(3) Belt
(2) Grease

Figure 10-15 Forecast Screen

By clicking the [Refresh] button, you can reacquire information on maintenance from the robot controller.

(1) Battery
If the number of remaining hours of battery life has reached
(Remainder time) < [The remainder days until presumed maintenance time] on the Setup screen)
x (24 - [Operation time of a day])
the hours and bar graphs are displayed in orange.
(The battery replacement time is calculated during the time when the controller’s power is not on.)

(2) Grease
If the hours until replenishment time has reached
(Hours until replenishment time) < ([The remainder days until presumed maintenance time] on
the Setup screen) x ([Operation time of a day]),

the hours and bar graphs are displayed in orange.

(3) Belt
If the hours until belt replacement time has reached
(Hours until belt replacement time) < ([The remainder days until presumed maintenance time] on
the Setup screen) x ([Operation time of a day]),

the hours and bar graphs are displayed in orange.

(4) Display unit

You can switch the display units for "Grease" and "Belts" between hours and days. When days are selected
as the display unit, the number of days of operation is calculated from the number of operating hours per day
and that number of days is displayed.

10-161 10-161
10.3.4. Settings
Here, you can set the timing for collecting information concerning maintenance forecasts, the notification
method, etc.

(1) Enables maintenance

forecasting

(2) Information
collection level

(3) Notice interval

(4) Warnings

(5) Output dedicated

output signal

(6) Operating time

per day
(7) Remainder
Figure 10-16 Setup

When the [Write parameters] button is clicked after setting each item, the setting values are written into the
controller. All items other than the signal numbers of dedicated outputs take effect after they are written into the
controller. If a dedicated output signal has been changed, it is necessary to power on the controller again.

For details on the setting items, see "Table 10-4 Description of the Setup Screen".

Caution
Information needed to “Maintenance Forecast” is not accumulated
while the Maintenance forecast is being invalidly set.
Reservoir of information
Factory preset value is invalidity. When the
Maintenance Forecast is invalidated,
information of Maintenance Forecast is not
accumulated. When switched effectively from
time
invalidity again, the reservoir of information is
Maintenance Forecast
continued from the last value. If you have Effective
invalidated the Maintenance Forecast for a long invalidity
Information is accumulated.
term, the correct maintenance times cannot be
calculated.

10-162 10-162
 Table 10-4 Description of the Setup Screen
Factory
Item Explanation preset
value
(1) Maintenance Forecast is If this is checked, the Maintenance Forecast function takes effect. Check
made effective. * If a checkmark is removed, the collection of the information for ON
Maintenance Forecast stops, and the correct maintenance times
cannot be calculated.
(2) Collection level of information Five levels can be specified to collect the information about the 1
maintenance. (Recomm
* As an information collection level gets higher, the accuracy of the ended)
maintenance improves, but it affects the tact time more.
(3) The interval of the forecast Specify the interval to notify the maintenance time. 6 hours
How to inform When the grease replenishment, belt replacement and other maintenance times
have reached, they can be notified by generating a warning or outputting a
dedicated signal. As for the battery replacement time, one of warnings, C7500,
C7510 and C7520, is generated, regardless of whether or not [Warning] under
[How to inform] is checked.
A warning to be generated varies depending on each situation.
(4) Warning If this item is checked, the maintenance time is notified as a warning. Check
The warning numbers are listed as follows: ON
Grease : C753* (* is the axis No.)
Belt : C754* (* is the axis No.)
(5) Output Signal If this item is checked, signal numbers can be entered. If this item is Check
checked and a signal number is entered correctly, the maintenance OFF
time is notified using the output of the designated signal.
(6) Assumption operation Enter an estimated robot operation hours per day. 16 hours
time of a day
(7) The remainder days until Specify the number of days remaining until presumed maintenance 14 days
presumed maintenance time to be used as a reference to notify the maintenance time.
time

Memo
Methods for resetting the alarm and alarm signal output
As a method of notifying the replacement time of each part, an alarm (C753* and C754* (* represents the axis
number)), or a dedicated output signal (M*PTEXC (* represents the robot number)) will be output.
If both are set up as the notification methods, executing the error reset operation will reset the alarm and end the
signal output.
If the “alarm” method is disabled and only the output of the dedicated output signal is selected as the notification
method, pushing the reset button on the front side of the controller will not end the signal output. In this case, push the
[ERROR RESET] key on the teaching box or enter the error reset signal (ERRRESET) to end the signal output.

Notification method Methods to reset the notification (alarm or dedicated signal output)
setting
Notification method [RESET] key on the [ERROR RESET] key External error reset
Output
Warning front of the controller on the T/B signal
Signal

Alarm Will reset the alarm Will reset the alarm Will reset the alarm

Alarm and Will reset the alarm Will reset the alarm and Will reset the alarm
dedicated signal and the dedicated the dedicated signal and the dedicated
output signal output output signal output
Will not reset the
Dedicated signal Will ENABLE reset the Will ENABLE reset the
dedicated signal
output dedicated signal output dedicated signal output
output

10-163 10-163
10.3.5. Reset screen
The information (about battery, grease and belt) for Maintenance Forecast kept in the controller can be reset.

Figure 10-17 Reset

Table 10-5 Description about each reset

Types of resets Explanation Note
At the time of It is used when an alarm urging to replace
battery exchange the batteries (C7500, C7510 or C7520)
occurs and the batteries have been replaced.
Be sure to reset the battery remaining time
after a battery has been replaced.
At the time of When an alarm urging to perform periodic Axes are reset in units of joint
grease inspections and replenish grease (alarm axes. Multiple joint axes can be
replenishment numbers in the 7530s) occurs, replenish the reset at the same time.
grease and reset the replenished axis.
At the time of belt When an alarm urging to perform periodic Axes are reset in units of joint
exchange inspections and to replace the belt when it is axes. Multiple joint axes can be
damaged (alarm numbers in the 7540s) reset at the same time.
occurs, replace the belt and reset the axis for
which the belt is replaced.

These reset operations can be executed using the teaching box. See the following section for further
details.

10-164 10-164
 When the [Log] button is clicked in the upper-right corner of the window, the previous reset date/time and
reset count can be checked.
However, the battery reset count is not displayed.
If no reset has not made previously, “----/--/-- --:--:--“ is displayed.

Figure 10-18 Log of Resets

10-165 10-165
10.3.6. Resetting maintenance forecast information with teaching box
When an alarm urges to replace the batteries, replenish the grease, or to replace the belt based on the
Maintenance Forecast function and these parts are replaced or replenished, the information that has been
accumulated within the controller needs to be reset for the axis where such replacement or replenishment has
been performed.
The information that has been accumulated within the controller can be reset using not only this software, but
also the teaching box.

(1) Resetting the time of battery remaining

Table 10-6 Resetting the time of battery remaining
Explanation Operation
the time of It is used when an alarm urging to From the teaching box (R32TB) menu screen,
battery remaining replace the batteries (C7500, C7510 or execute "5. Settings and Initialization" → "1.
C7520) occurs and the batteries have Initialization" → Battery.
been replaced.
Be sure to reset the battery remaining
time after a battery has been replaced.

For details on the method for initializing the battery remaining time using the teaching box, in the robot
controller's operations manual, see "Details of Functions and Operations".

(2) Resetting the grease and belt information

The grease and belt information can be reset by entering parameters to the controller.
The following is the list of parameter names and the values to be entered.

Table 10-7 Resetting the grease and belt information

Explanation Parameter Value
Grease When an alarm urging to perform MFGRST
information periodic inspections and replenish
grease (alarm numbers in the 7530s)
occurs, replenish the grease and reset 0 : Reset information on all
the replenished axis. axes
Belt When an alarm urging to perform MFBRST
information periodic inspections and to replace the 1 to 8 : Reset information on the
belt when it is damaged (alarm specified axis
numbers in the 7540s) occurs, replace
the belt and reset the axis for which
the belt is replaced.
(* These parameters cannot be read not to input all characters in the teaching box.)

The grease or belt information will be reset immediately after a parameter name and the value are entered.
(In this case, the controller power does not need to be restarted.) If a value other than 0 is entered, the reset
process will be executed for each axis.
Repeat the parameter input operation when resetting information on two or more axes.
Also note that the value read is always 0 regardless of the previously entered value. If you continue the input
operation in this state, all axes will be reset. Exercise with caution.

See “Controller INSTURCTION MANUAL – Detailed explanations of functions and operations” for how to
input parameters using the teaching box.

10-166 10-166
10.3.7. Others
The information for Maintenance Forecast kept in the controller can be backed up and/or restored.

Caution
The backup and restore operations are performed when the
controller (CPU) is replaced.
When the controller (CPU) is replaced, perform both backup and restore operations in a batch using the
Backup/Restore tool. Also, be sure to back up the information for Maintenance Forecast before replacement,
and restore the backed up information after replacement.
After the controller (CPU) has been replaced, if the information for Maintenance Forecast is not restored, or
it is restored after a substantial time has elapsed since the time of backup, please note that the reliability of
Maintenance Forecast will be degraded.

Figure 10-19 Others

10-167 10-167
10.4. Position repair Function
The position repair function is restricted by the usable models and controller software versions. See "Table
10-9 Supported Robot Controllers and Model".

The "position repair function" is used when a tool is deformed by a collision or the origin is out of place
because the motor has been replaced. Just reteaching part of the position data within the robot program makes
it possible to use the previous position data in the controller. (Position repair generates parameters to correct
the position deviation and corrects all the position data in the robot controller.)
However, please understand that there are some cases that position repair can not restore, such as
applications requiring high precision and major mechanical damage to a robot from a collision.
Also, restrictions on a robot's degrees of freedom can make it impossible to recover with position repair.
Since vertical 5-axis robots and horizontal 4-axis robots are restricted as shown in "Table 10-8 The limit by
degree of freedom", positional deviations related to these restrictions can not be corrected with this function.
In this case, either reteach manually or correct the deviating section (for example, by replacing a bent hand).

Table 10-8 The limit by degree of freedom

No. Robot model The limit by degree of freedom
It can’t move in the direction of C element of the Cartesian
1 Vertical 5-axis robot
position.
It can’t move in the direction of A, B element of the
2 Horizontal 4-axis robot
Cartesian position.

Caution
The position repair function is only supported by MELFA-BASIC IV
and MELFA-BASIC V.
The position repair function is only supported by MELFA-BASIC IV and MELFA-BASIC V. It cannot be used
with Movemaster commands.

10.4.1. Specifications
The robot models and robot controller versionw with which the position repair function can be used are as
follows.

Table 10-9 Supported Robot Controllers and Models

CRn-700 series
No. Robot model CRn-500 series Robot Controller
Robot Controller
Version J2 or later
1 Vertical 6-axis robot Only correction of origin data is supported in
versions prior to J2.
The supported Version K1 or later
2 Vertical 5-axis robot models are not Only correction of origin data is supported in
restricted by the versions prior to K1.
version Version K4 or later
Horizontal 4-axis
Any versions prior to K4 are not available.
3 robot
Moreover, This function cannot be used for the
(RH-SH series only)
RH-AH series robot.

10-168 10-168
10.4.2. Starting
Use the position repair function while connected to the robot controller.
From the project tree, double click the target project [Online] → [Maintenance] → [Position repair].

Figure 10-20 Starting Position Repair

10-169 10-169
10.4.3. Flow of operations
The position repair takes the form of a wizard. You can automatically generate the parameters by proceeding
with operations according to the instructions on each screen. You can directly set parameter values.

Specify the target robot

Backup the parameters before

Automatic parameter
generation If setting parameters
(Normal operation)

Specify the program to use for parameter Enter parameter values

generation (within robot controller)

Write parameters to robot controller

Back up the selected program

Restart robot controller power

Specify the parameters to be generated

Re-teaching Work Procedure

Move robot to re-teaching position Repeat as necessary

(Use the teaching box)

Execute re-teaching calculation

Parameter generation

Write parameters to robot controller

Restart robot controller power

Figure 10-21 Operation Flow

The explanation follows the normal operations flow. For the explanation when setting parameter values, see
"10.4.16 Revision parameter editing".

10-170 10-170
10.4.4. Introduction

Figure 10-22 Starting Use Window

This is an explanation of the position repair function. Read it carefully, then click the [Next] button.

10.4.5. Communications settings

Check the communication settings and connected to the robot controller, click the [Next] button. For the
setting method, see "5 Connecting with the Robot".

10-171 10-171
10.4.6. Robot selection and parameter backup

Figure 10-23 Robot and Backup Parameters Selection Window

Select the robot to execute the re-teaching.

The Robot is displayed as follows.

Controller number : Controller Name + Mechanism Name #Mechanism No.

Dis played only in multi-mechanism mode

To backup parameters, click [Backup].

The dedicated backup screen starts. For more details on backups, see "12 Backup and Restore".
Backed up parameter files can be written back to a robot controller using the "backup/restore" functions of
this software.

When the preparations are complete, click the [Next] button.

Memo
Parameter Backup
During its operation, this software overwrites parameters to the robot controller.
It is recommended that the parameters be backed up at this point to allow the controller to revert to the original
parameters.

10-172 10-172
10.4.7. Revision parameter generation procedure selection

Figure 10-24 Select generation procedure of revision parameter Window

In the next step, the software can either automatically generate parameters or accept manually entered
parameter values. Normally, [Generate revision parameter automatically] is selected.

Select [Generate revision parameter automatically] and click [Next] to proceed to “Select Program” window.
Select [Edit the value of revision parameter directly] to proceed to “Edit Revision Parameter” window.

10-173 10-173
10.4.8. Program selection

Figure 10-25 Select Program Window

Select the robot program to use for revision parameter generation, then click the [Next] button.
Here, perform the reteaching using the XYZ-coordinate position data in the selected program.

For details on the required position data numbers, see "Table 10-10 Selecting Revision Parameters".

Memo
The points on selecting the program
Select the program with the positions of various location and posture.
Moreover, higher accuracy of revision parameters can be obtained by selecting the following type
of position data program.
・ Program with positions that are easy to re-teach
・ Program with positions that require high precision

10-174 10-174
10.4.9. Program reading and backing up

Figure 10-26 Read and Backup Program Window

To backup a program, click [Backup].

The special screen for backup starts. For details on backups, see "12 Backup and Restore".
You can use the backup/restore functions in this software to write a backed up parameter file back into a robot
controller.

When the preparations are complete, click the [Next] button.

Memo
Robot Program Backup
During its operation, this software may overwrite robot controller program (position data).
It is recommended that the program be backed up at this point to allow the controller to revert to the original
program.

10-175 10-175
10.4.10. Tool setting check

Figure 10-27 Check of Setting Tool Window

Parameter values set in the present robot controller for tool data are displayed. The row for the tool selected
by the tool number (MEXTLNO) is highlighted in red.
Please check if the tool data and tool number used during teaching is set.
If necessary, change the value from parameter setting in teaching box. Click [Renew List] to update the
contents of the display.
(If the CRn-500 series robot controller’s version is older than J2, only the standard tool (MEXTL) will be
displayed.)

Click [Next] when ready to proceed.

Caution
Do not change tool data or base data.
After this window, do not change tool data or base data.
If they are changed during re-teaching operation, re-teach calculation cannot be done correctly.
When correcting tool data, if teaching was performed switching back and forth between multiple
tools, perform re-teaching operation for each tool.

10-176 10-176
10.4.11. Revision parameter selection

Figure 10-28 Select Revision Parameter Window

Select the revision parameter that becomes the target for re-teaching calculation.

Revision parameter will be selected automatically if an item is selected from [Select revision parameter].
Choose [Select all] to select all the revision parameters. If you wish to specify a particular combination of
revision parameters, choose [Select arbitrarily] and specify the revision parameters.

If the CRn-500 series robot controller’s version is older than J2, only
Vertical 6-axis robot
[Error of joint axis] can be selected.
If the CRn-500 series robot controller’s version is older than K1, only
Vertical 5-axis robot
[Error of joint axis] can be selected.
The CRn-500 series robot controller’s any versions prior to K4 are not
Horizontal 4-axis robot
available.
(RH-SH series only)
(This function cannot be used for the RH-AH series robot.)
The supported models are not restricted by the version in CRn-700 series robot controller.

Click [Details] to see the description of the difference between checking and not checking [Use the posture
elements of position data].

In the following section, details regarding revision parameters and posture elements of position data are
explained.

After choosing the revision parameters, click [Next].

10-177 10-177
10.4.11.1. Revision parameters
Parameters revised by items selected with "Select revision parameters" become as in "Table 10-10
Selecting Revision Parameters".

Memo
Some elements cannot be calculated according to
the robot type and the combination of revision parameters.
In this function, the amount of the gap of the robot is calculated as a correction value, and the revision
parameter is generated. However, some elements cannot be calculated (the value becomes 0) as the following
two kinds of cases.

* The case which cannot be calculated by the limits of degree of freedom of robot
Some elements of revision parameter cannot be reflected because the Vertical 5-axis robot and horizontal
4-axis robot have the limitation.

* The case which condensed by the combination of robot mechanism and revision parameter
Some elements of revision parameter become the value on the same rotation axis according to the
combination of robot mechanism and revision parameter. In such case, calculated value of gap is condensed to
the one element of revision parameter.
At this case, though the other element becomes 0, it condenses in other elements and it is corrected. So it is
not necessary to reflect it again.

10-178 10-178
 Table 10-10 Selecting Revision Parameters
Minimum number of teach
points
Revised Horizo
No. Item Description Vertical Vertical
Parameter ntal
6-axis 5-axis
4-axis
robot robot
robot
Rectifies origin data when joint axis moves or when Origin data
motor is replaced.
Error of 1 to 6 1 to 5 1 to 4
1 Specify the target axes using the check boxes.
joint axis points points points
The number of teaching points is different according
to how the axis was specified.
Rectifies attachment error when robot tool is
exchanged. In addition, rectifies tool data error when Tool data
Tool the tool is transformed due to interference between
exchange robot and peripheral devices. 3 to 6 3 to 4
2 1 point
or points points
Vertical 5-axis robot:
modified
* Only Z element of position data is corrected.

Rectifies base data of robot position setup when the

robot is transferred to another location. Base Data
Transfer Vertical 5-axis robot: 3 4
3 6 points
the robot * Only X, Y, Z elements of position data are points points
corrected.

When robot is exchanged with the tools on, rectifies

origin data error and base data of robot position Base data
setup. Origin data
Only for horizontal 4-axis robot, attachment error is
also rectified. Tool data
Vertical 6-axis robot: (4-axis robot
* Origin data J1 is included in base data. only)
Vertical 5-axis robot:
* As to base data, only X, Y, Z elements are 10 to
Exchange Corrected. 7 to 8 7 to 8
4 11
the robot Horizontal 4-axis robot: points points
points
* Origin data J1 and J3 are included in base data. (5-axis and
* Origin data J3 and J4 are included in tool data. 6-axis robot)
* Select which to be requested because Z elements
of tool data and base data are not corrected at the
same time.

(4-axis robot)

Selects all revision parameters.

Vertical 6-axis robot:

* Origin data J1 is included in base data.
* Origin data J6 is included in tool data.
Vertical 5-axis robot:
* As to tool data, only Z element is corrected. Origin data
* As to base data, only X, Y, Z elements are Tool data
corrected. Base data 13 to
8 to 9 7 to 8
5 Select all Horizontal 4-axis robot: 16
points points
* Origin data J1 and J3 are included in basedata. points
* Origin data J3 and J4 are included in tooldata.
* Select which to be requested because Z elements
of tool data and base data are not corrected at the
same time.

10-179 10-179
 Minimum number of teach
points
Revised Horizo
No. Item Description Vertical Vertical
Parameter ntal
6-axis 5-axis
4-axis
robot robot
robot
Specify revision parameters.
Vertical 6-axis robot:
* Since origin data J1 is included in base data, if
base data is selected, turn off the Checkbox of
origin data J1.
* Since origin data J6 is included in tool data, if tool
data is selected, turn off the Checkbox of origin
data J6.
Vertical 5-axis robot:
* As to tool data, only Z element is corrected.
* As to base data, only X, Y, Z elements are
corrected.
Select Horizontal 4-axis robot:
6 * If base data is selected, turn off the Checkboxes
Arbitrarily
of origin data J1 and J3.
Origin data J1 and J3 are included in base data.
* If tool data is selected, turn off the Checkboxes of
origin data J3 and J4.
Origin data J3 and J4 are included in tool data.
* If tool data and base data are selected together,
select which Z element to be requested, because
Z elements of tool data and base data are not
corrected at the same time.

* Revision parameter names correspond to the following.

Origin data: DJNT
Tool data: MEXDTL, MEXDTL1 to 4 (Parameter of the tool selected by tool number)
Base data: MEXDBS

10-180 10-180
10.4.11.2. Position data posture components
Position data of MELFA-BASIC IV consists of tip position (X, Y, Z) and tip posture elements (A, B, C) (*1).
This section describes the cases where [Use the posture elements of position data] is checked and not
checked.

Memo
(*1) The posture elements of position data
In case of the vertical 6-axis robot, the posture elements of position data are (A, B, C).
In case of the vertical 5-axis robot, the posture elements of position data are (A, B).
In case of the horizontal 4-axis robot, the posture element of position data is (C).

(1) [Use the posture elements of position data] is checked

Not just the robot tip position (X, Y, Z) but also the tip posture elements are used for position correction
calculation.
Precision of generated revision parameter improves if the tip posture elements are also re-taught correctly.
However, if the tip posture elements are not re-taught correctly, as shown in the diagrams below
(re-teaching positions P1 and P2), error occurs in position correction calculation, decreasing the precision of
the calculation result.
If posture elements are not re-taught accurately

If posture elements are

re-taught accurately Re-teaching position

Original position and posture

Position and posture before
re-teaching
Position and posture after
Original position Re-teaching Re-teaching Re-teaching
re-teaching
and posture position P1 position P2 position P3

(2) [Use the posture elements of position data] is not checked

Posture elements in the position data taught during re-teaching are not used for position correction
calculation.
If it is not necessary to match exactly the tip posture elements during re-teaching, clear the checkbox [Use
the posture elements of position data]. In such case, position correction calculation is performed using only
the tool tip position data (X, Y, Z), ignoring the error from posture deviation. This increases the precision of
location correction.
However, there are some restrictions. For details, see "Table 10-11 About Posture Elements of
Re-teaching Position Data".

10-181 10-181
 Table 10-11 About Posture Elements of Re-teaching Position Data
Condition Merit Note
When using posture elements of Precision of generated During re-teaching, posture must
position data revision parameter improves be taught correctly. If posture
if the tip position (X, Y, Z) data is incorrect, precision of
and tip posture elements are revision parameter actually
re-taught correctly. decreases.

When not using posture elements of During re-teaching, revision In case of the vertical 6-axis
position data parameters can be robot :
generated simply by * Posture elements (A, B, C) of
correctly teaching position tool revision parameters cannot
(X, Y, Z). be obtained.
(Posture elements need not * J6 axis of origin revision
be accurate.) parameter cannot be obtained
if both X and Y components of
the tool parameter are 0.0.
In case of the vertical 5-axis
robot :
* J6 axis of origin revision
parameter cannot be obtained.
In case of the horizontal 4-axis
robot :
* Posture elements (C) of tool
revision parameters cannot be
obtained.
* J4 axis of origin revision
parameter cannot be obtained
if both X and Y components of
the tool parameter are 0.0.

10-182 10-182
10.4.12. Reteaching work

Figure 10-29 Reteach Work Window

[Remainder] Displays the number of remaining points until revision parameters are
generated.
However, at some positions, re-teaching may not decrease the number
of remaining points.
[Re-teach] button Specifies the positions selected in the list and opens “Re-teach the
position” screen.
[Clear] button Clears the re-teaching information for positions selected in the list.
[Check of tool data] Displays current tool data setting in the robot controller.

Caution
Position data of the targeted program is write-protected.
During showing this window, the position data of the targeted program in the controller is write-protected. If this
tool is interrupted when not communicating with the controller, the position data cannot be unprotected. Please
release the protect by using the Teaching Box or Program manager of this software.

Position data for the program selected are displayed.

Select the position to re-teach from the list and repeat re-teaching to generate revision parameters.

Re-teaching work procedure can be described as follows. While the “Re-teach the position” screen is open,
move the robot to the re-teaching position and click the [Load current position] button on the screen.

10-183 10-183
 Figure 10-30 Re-teach the position Screen

Re-teaching
Repeat
Select the position to re-teach from the list

Click [Re-teach] button Re-teach the position Screen opens

Re-teach the position Screen

Move the robot to re-teaching position

(Use the teaching box to move)

Click [Load current position] button

(Re-teaching calculation) Position Re-teaching window closes

Revision parameter generation

Figure 10-31 Re-teaching Work Procedure

Row for re-taught position will be highlighted in light blue.

Re-teaching does not change the position data values shown in the list.

Caution
Do not perform position correction using the teaching box.
When you move the robot to the re-teaching position using the teaching box, be careful not to correct the
position.
During re-teaching, position data of the applicable program in the controller is write-protected.

10-184 10-184
 Caution
Do not change tool data, tool number, or base data.
Do not change tool data, tool number, or base data during re-teaching. Re-teaching calculation will not be
performed correctly.
When correcting tool data, if teaching was performed switching back and forth between multiple tools, perform
re-teaching operation for each tool.

Caution
Select position data with a different posture element, when
re-teaching two or more positions.
Select position data with a different posture element, when re-teaching two or more positions.
When position data of the same posture element are selected, there is a possibility that the parameter is not
correctly calculated.

Caution
The cautions when using a robot with the additional axis.
When restoring the position with a robot with a travel axis, reteach at a position where the travel position
becomes the same as in the original position travel axis data. (Move the robot so that the travel axis data
becomes the same as the original position.) If the retaught position travel axis data differs from the original travel
axis data, it is impossible to find the correct revision parameters.

It is possible to change the revision parameters to be generated.

Go back one step to the “Select revision parameter” window to change the setting. Note that if you return
one more step to “Check of setting tool” window, all information set by re-teaching work will be cleared.

Caution
When go back to “Check of setting tool” window, all information set
by re-teaching work will be cleared.

10-185 10-185
10.4.13. Writing parameters

Figure 10-32 Write Parameters Window

[Print] Prints the revision parameter information displayed in the list.

[Save position data to file] Saves position data used in re-teaching as a robot program with
positions only. Position data will be values converted by the revision
parameters.

Revision parameters and their values generated by re-teaching are displayed.

Click [Next] button to write the parameters into the robot controller.

Caution
If revision parameters could not be generated
If revision parameters could not be generated, parameters are not displayed in the list.
If you click the [Next] button, position data used in re-teaching is written into the robot controller.
Since parameters are not generated, position data will not be converted.

Parameters may not be generated under the following conditions.

* When one of the specified re-teaching positions is of a significantly low precision
* When one of the original position data is of a significantly low precision
* When the difference between the original position data and the re-teaching position is too large
* When tool data or base data was changed during re-teaching

Clicking the [Back] button and redoing a part of the re-teaching may generate revision parameters.
Please delete the re-teaching information for the position data that meets one of the criteria mentioned above
and perform re-teaching again.

10-186 10-186
10.4.14. Controller power supply Off, On

Figure 10-33 Re-start the power supply of the controller Window

To activate the written parameters, turn off and then turn on the power of robot controller.

10-187 10-187
10.4.15. Exit

Figure 10-34 Finish Window (After Re-teaching)

When the writing of revision parameters is done, operation of this function is complete.

Caution
Perform an operation check before exit this function.
Before exit this window, make sure that all position data works properly.
If revision is not correct, click the [Return to re-teach] button to continue re-teaching. (However, if you exited
from “Edit revision parameters” window, [Return to re-teach] button will not be shown.)

Caution
Back up the parameters.
This Function has changed the revision parameters. Back up the parameters before exit this window.

Caution
Position data close to operation area boundaries may not be
rectifiable.
Around the operation area boundaries, position error may put a point outside the operation area, in which
case this function cannot rectify the point.

10-188 10-188
10.4.16. Revision parameter editing

When you select "Edit the value of revision parameter directly" with "10.4.7 Revision parameter generation
procedure selection", this screen is displayed.

Double click

Figure 10-35 Edit Revision Parameters Window

[Print] Prints the revision parameter information displayed in the list.

[Reset] Resets all changes.

Displays values of current revision parameters in the robot controller.

Select parameter from the list and double-click it to display the setting screen. Set the parameter values.
(If the CRn-500 series robot controller’s version is older than J2, only the origin revision parameter (DJNT) is
shown.)

Click [Next] to write all parameters into the robot controller and proceed to “Re-start the Power Supply of
the Controller” window.

10-189 10-189
10.5. Servo Monitor

This monitors servo information.

10.5.1. Load

The load state of each robot axis can be monitored.

Click [Reset] button to reset the max axis load level of monitored load information.

Figure 10-36 Servo monitor Load

10-190 10-190
11. Option Card
You can check information on option cards mounted in the robot controller.

When you open [Option Card] on the project tree, the slots in which option cards are currently mounted and
the option card names are displayed. If you place the mouse cursor on an option card name, the information for
that option card is displayed.
If no option card is mounted on the robot controller, nothing is displayed.

Figure 11-1 Option Card Information

11-191 11-191
12. Backup and Restore
You can back up information in a robot controller to the computer.
You can also restore backup information saved to the computer back into a robot controller.

Backup Saves the backup data on the robot controller to the personal
(Robot -> Personal computer) computer.
Restore Transfers the backup data saved on the personal computer to the
(Personal computer -> Robot) robot controller.

Caution
Precautions when executing a backup/restore operation during the
replacement of a controller (CPU) that supports Maintenance
Forecast
When executing a backup/restore operation during the replacement of a controller (CPU) that
supports Maintenance Forecast, also perform the backup/restore operation using the Maintenance
Forecast tool.

After a backup operation is performed on a controller that supports Maintenance Forecast, the following
message is displayed:

Figure 12-1 Backup When Maintenance Forecasting Information Is Enabled

* When using a CRn-500 series robot controller, maintenance forecasting is supported for software versions J2
and later.

12-192 12-192
12.1. Backup(Robot -> PC)
You can save information in a robot controller to a file in the computer.
Use the backup function while connected to the robot controller.

(1) From the project tree, open the target project [Backup]. In the backup tree, "All file", "Program information",
"Parameter files", and "System program" are displayed.

Figure 12-2 Backup Project Tree Diagram

All Files Saves all files (robot program, parameter files, etc.) in the robot controller into
the designated folder.
Program Saves the robot program file into the designated folder.
Parameter Files Saves the parameter files into the designated folder.
System Program Saves the system base program file into the designated folder.

(2) Double click the items to backup.

Double click

Figure 12-3 Backup (When Batch Is Selected)

[Parameter List Files] : This is used to edit the parameter information saved by backup in offline
mode, and is not required for backup. If this is not checked, the time
required to save all files will be shortened.

(3) Specify the backup destination. The default value is the folder that created the workspace/project
name/Backup/today's date and time.
You can change the backup destination folder with the […] button at the right of the displayed backup
destination.

You can back up other items at the same time too by putting checkmarks in their checkboxes. In this case,
the data is backed up to the backup destination selected above with an identifier for the backup type
suffixed to the folder name. The identifiers are as follows.
All…ALL Program information…PRG Parameter information…PRM System program…SYS

12-193 12-193
 The folder name at this time is displayed on the right side of the respective backup items.

Figure 12-4 Backup (When Multiple Selected)

(4) Specify the back destination, then click the [OK] button.
The confirmation screen is displayed. When you confirm, then click [Yes], the backup is started.

Figure 12-5 Backup Confirmation Screen

When the backup is completed, the backup data is displayed at [Backup] on the project tree.

Figure 12-6 Display of Backup Information

Caution
Cautions for backups
The objective of backup data is to back up robot controller information. Note that backed up robot programs
can not be edited with the "Program edit" screen.

When backing up system status variable values and program external variable values, switch the robot
controller power Off, then On again, then perform the backup operations.

The files BKUP.SYS and MECHA.SYS are automatically created in the specified folder. These files record the
saved robot controller mechanical information and save format. Be careful. If you delete or rewrite these files,
this may make it impossible to restore them to the robot controller.

12-194 12-194
12.2. Restore (PC -> Robot)
You can take information back up to the computer and transfer it to a robot controller information.
Use the restore function while connected to the robot controller.

(1) From the project tree, open the target project [Backup]. In the backup tree, the information back up for "All
file", "Program information", "Parameter files", and "System program", respectively, is displayed.

Figure 12-1 Backup Project Tree Diagram

(2) Select the information listed on the controller, then click the right mouse button. From the right mouse button
menu, select [Restore].

Figure 12-2 Restore

All Files : Transfers all files (except BKUP.SYS and MECHA.SYS) in the designated
folder to the robot controller after all information in the robot controller is
cleared (initialized).
Program : Transfers the robot program file in the designated folder to the robot
controller.
Parameter Files : Transfers the parameter file in the designated folder to the robot controller.
System Program : Transfers the system base program file in the designated folder to the robot
controller.
Change Robot Origin : This is backup information and it only valid when All or Parameter files is
Data selected. Operations for when this checkbox is checked and when it is not
are as in "Table 12-1 ".
Change Robot Arm : If you check this checkbox, the robot main unit serial number is also
Serial Number rewritten.

12-195 12-195
 Table 12-1 Operations for "Change Robot Arm Serial Number Too"
Check ON Check OFF
Controller

Parameters(B) Parameters(B)
<リストア前> <リストア前>
Restore Restore
files Origin data(B) files Origin data(B)

parameters for parameters for

position repair (B) position repair (B)

CRn-700 <before restore> <after restore> <before restore> <after restore>

series controller controller controller controller

or
Parameters(A) Parameters(B) Parameters(A) Parameters(B)
CRｎ-500
series Origin data(A) Origin data(B) Origind ata(A) Origin data(A)
J2 edition
or later parameters for parameters for parameters for parameters for
position repair (A) position repair (B) position repair (A) position repair (A)

An initial value will be used if the file to

be restored does not have any
revision parameter for position repair.
A backed up file is transferred. However, as
Transfers a backed up file as is. The origin for the origin data and the parameters for
data is replaced. recovering positions, the information inside the
controller is retained.

Parameters(B) Parameters(B)
Restore <リストア前> Restore <リストア前>
files files
Origin data(B) Origin data(B)

parameters for parameters for

position repair (B) position repair (B)

<before restore> <after restore> <before restore> <after restore>

controller controller controller controller
CRｎ-500
series
Parameters(A) Parame ters(B) Parameters(A) Parameters(B)
H7 edition
or earlier
Origin data (A) Origin data (B) Origin data(A) Origin data(B)

Revision parameters for position Revision parameters for position

repair will not be written repair will not be written.

Transfers a backed up file as is. The origin A backed up file is transferred. However, as
data is replaced. for the origin data, the information inside the
controller is retained.

Be careful. If communication is cancelled during a series of restore processing, the position revision
parameters generated with the "Position repair" function and the origin data may be changed.

12-196 12-196
 Caution
Precaution for Restore
If a batch restoration or a program restoration is executed when the program is being started, the program will
automatically be stopped.
At this time, if there is an error in the controller,
the program in operation cannot be stopped, and
the message shown on the right will be displayed.
Although a restoration process can be executed even
in such a case, the program currently selected or the
program that is started by ALWAYS cannot be re-written.
If it is possible to remove the cause of the error,
reset the error and execute the restoration process again.

12.3. Deleting Backup Data

You can delete the backed up information.
Select the information to delete, then click the right mouse button. From the right mouse button menu, select
[Delete].

Figure 12-3 Deleting Backup Data

It is also possible to delete all the backup data.

Right click [Backup] for the target project. From the right mouse button, click "Delete All".

Figure 12-4 Deleting All the Backup Data

Caution
Be aware that once backup data is deleted, you can not restore it.

12-197 12-197
13. Simulation
This chapter explains the simulation operation methods.

Caution
Simulation can not be used with the mini edition.
The simulation function only supports the "RT ToolBox2" standard edition. It can not be used with the mini
edition.

Simulation can not be used with Movemaster commands.

Be aware that even with the standard edition, the simulation function can not be used when Movemaster
commands are selected.

You can not communicate with the robot controller during a

simulation.
You can not communicate with the robot controller during a simulation. To communicate with the robot
controller, click on the menu bar [Online] → [Offline] to end the simulation, then again click on the menu bar
[Online] → [Online] to connect the robot controller.

With an actual robot, an overload error might occur.

Be aware that even if you run the simulation with the work and hand weight set and this works properly in the
simulation, when you actually operate with the robot, an overload may occur and make operation impossible.

If there is an input signal wait in the program, use pseudo-input.

When you execute a program in simulation and there is an input signal wait in the program, the program does
not move to the next step until that command is executed. Therefore, if there is an input signal wait, use the
pseudo-input function from the signal monitor.

13-198 13-198
13.1. Starting a Simulation
Click on the menu bar [Option] → [Simulator]. At that time, if there are two or more projects in the workspace,
the screen for selecting the screen to conduct the simulation is displayed.

Figure 13-1 Project Selection When Simulation is Started

Select the project to start the simulation of, then click the [OK] button.

Caution
You can only simulate one project.
You cannot simulate multiple projects at the same time.

You can also start a simulation through operations from the tool bar.
Switch to "Offline".

Switch to "Online".

Switch to "Simulation".

Figure 13-2 Explanation of Toolbar

When the simulation start-up is complete, the operation screen for the simulation is displayed on the screen.
Also, the virtual controller for the simulation is automatically started up as an icon. The simulation is run by this
virtual controller. The virtual controller ends automatically when the simulation ends. Do not end the virtual
controller manually.

Figure 13-3 Virtual Controller

13-199 13-199
13.2. Explanation of the Simulation Operation Screen
This is a simple explanation of the simulation operation screen.

(4) Jog operation

(1) Status

(2) OVRD

(6) Step execution

(3) Jump

(7) Continuous execution

(5) Stop
(9) Reset

(8) Servo On/Off (10) Direct execution

Figure 13-4 Simulation Operation Screen

(1) Status
This shows the task slot status for simulation.

(2) OVRD
This displays and sets the robot speed override.

(3) Jump
You can specify the line in the program to execute.

(4) Jog operation

This conducts jog operations for the simulation robot. When you click this button, the jog operation screen
is displayed.

(5) Stop
When a program is running in a simulation, this stops the program.

(6) Step execution

This executes the specified program one line at a time.

(7) Continuous execution

You can execute the stopped program again from the line on which is was during with a stop instruction or
a breakpoint during program running.

(8) Servo On/Off

You can switch the simulation robot servo On/Off.

(9) Reset
You can reset the program and any errors that have occurred.

(10) Direct execution

You can execute any command without relationship to the robot program.

13-200 13-200
13.3. Robot View Start
You can display the robot whose simulation you are running and its movements in 3D to check them.

With the simulation running, from the project tree, either double click [Online] → [<Robot model name>] or
select [3D Monitor] with the mouse right button menu. The 3D display screen for the set robot is displayed.

Double click the robot type name

or
select [3D Monitor] with the mouse right
button menu.

Figure 13-5 Robot View Start

The robot view perspective can be changed with mouse operation.

Table 13-1 Robot View Perspective Change Operations

Viewpoint of changing Mouse operations on the graphic
Rotation While clicking the left button, move left/right → Rotation around Z
axis
Move up/down → Rotation around X axis
Move left/right while clicking the left + right buttons → Rotation
around Y axis
Move Move up/down/left/right while clicking the right button
Enlargement/reduction Move up/down/left/right while clicking pressing [Shift] key and
clicking the left button

13-201 13-201
13.4. Robot Program Selection
Select the robot program to run the simulation. Step operation or direct execution in the simulation are not
possible unless a program is selected.
In the simulation, from the project tree, with [Online] → [Program], execute "Open in debugging status" for the
program from the right mouse button.
If the robot program being simulated is not [Online], use program management to copy to the virtual
controller.

Figure 13-6 Program Selection for Simulation

The specified robot program is opened in debugging status. The execution line cursor " " is displayed at the
left end of the command statement edit area. The line on which this execution line cursor is displayed is the line
currently being executed.
The display of this execution line cursor can be switched on/off with the menu bar [Debug] → [Display/Do not
display].

13-202 13-202
13.5. Program Execution
You can execute a program that has been opened in debugging status.
Start the simulation, then open the robot program in debugging status. When you click the [Continuous
Execute] button on the simulation operation screen, automatic operation of the program is started. This
automatic operation completes in one cycle. Be careful. If the program repeats infinitely, it does not stop
automatically.

Continuous execution

Figure 13-7 Program Execution

To forcibly stop a program that is executing, click the [Stop] button on the simulation operation screen.

13.6. Specifying the Starting Line for Program Execution

You can freely specify the line in the program from which to start execution. Use [Jump] on the simulation
operation screen Input the step number to start execution from, then click the button on the right side of the
input box. The current execution line moves to the specified step number.

Jump button

Step number input box

Figure 13-8 Program Execution Line Execution

13-203 13-203
13.7. Breakpoint Setting
You can also use breakpoints in a simulation. For details on the operation method for breakpoints, see
"7.9.4 Setting and deleting breakpoints".

13.8. Step Operation

A program that has been opened in debugging status can be executed step by step.
Start the simulation, then open the robot program in debugging status. Step operation in simulation is
performed from the simulation operation screen.

Step execution

Continuous execution

Figure 13-9 Simulation Operation Screen

Operate with the [FORWD] button and [BACKWD] button in the [Step Execution] group on the simulation
operation screen.
Pressing the [FORWD] button executes the command on the current execution line and advances the current
execution line by line. Pressing the [BACKWD] button executes the command on the current execution line and
returns the current execution line by line.

13-204 13-204
13.9. Direct Execution
You can input command statements and operate the robot directly.
Click the simulation operation screen [Direct execution] button.

Direct execution
Figure 13-10 Starting Direct Execution

Input the command to execute into the command box, then either press the keyboard [Enter] key or click the
[Execute] button. The input command is executed. At this time, if a position variable is specified in a move
command or a like, the position variables defined in the currently open program are used. A position variable not
defined in the program can not be used.
A command that has been input once into the command box is added to the history and can be selected from
the command box dropdown list. However, when the simulation is ended, the history and dropdown list
commands are commanded

Figure 13-11 Command Dropdown Liston Direct Execution Screen

This operation is not possible during automatic running with the [Continuous Execution] button.

Caution
When executing directly, select the program to execute.
Direct execution can not be used unless a program is selected. Always open a program in debugging status
and put it in selected status.

13-205 13-205
13.10. Jog Operation
You can perform the jog operations displayed in the robot view in the simulation status.
Click the simulation operation screen [Jog] button. The screen for jog operations is displayed at the bottom of
the simulation operation screen.

Jog
operation

Jog operation
screen
(1) Robot model section

(2) Hand align

(4) Movement distance
(3) Move method setting

(5) Current robot position (6) Axis jog operation

Figure 13-12 Starting Jog Operation

(1) Robot model select

When multiple robots are set as connected, select the robot model to operate.

(2) Hand align

You can align the posture of a hand installed on the robot in units of 90 degrees.
This function moves the value to the multiple of 90˚ that is closest to the A, B, and C components of the
current position.

(3) Move method

Select the robot move method. The robot move methods are "Joint" and "XYZ".
The robot current position display and the jog operation button display for each axis use the method
selected here. Also, these displays depend on the axis configuration of the connected robot.
When "Joint" When "XYZ"

Figure 13-13 Screens for Jog Operation with Different Move Methods Selected

13-206 13-206
(4) Distance setting for moving
This selects the robot move distance. The robot move distances are "off", "High", and "Low".
For a detailed explanation of the move distance, see "Detailed Explanation of Functions and
Operations" in the robot controller's user's manual.

(5) Robot current position

This displays the current robot position.

(6) Jog operations on each axis

This conducts jog operations on each robot axis.
Moves the selected robot axis in the "-" direction.
Moves the selected robot axis in the "+" direction.
These buttons move the robot while the mouse button is held down.

13.11. Simulation Robot Position Variable Editing

You can edit position variables by moving the simulation robot and reading the position variables from the
simulation robot posture.
Move the robot to the target position with jog operations.
Click the [Add] button or [Change] button for position variables in a program opened in debugging status to
display the position edit screen, then click the [Read current position] button. You can read in the current
position of the simulation robot.

13-207 13-207
13.12. Tact Time Calculation
You can use the simulation function to calculate the tact time for a program prepared.

Caution
Tact time calculation
The calculated tact time varies with the capacity of the computer used and its load status and does not
completely match the actual robot operating time (tact time).
Use this function as a rough yardstick for tact time study.

Under correct conditions, the results of tact time calculation with this software have an error of about ±3%
compared to the actual robot operating time (tact time).

For details on tact time deviation, see "13.12.3 Causes of tact time deviation".

13-208 13-208
13.12.1. Conditions for tact time measurement
Be aware of the following restrictions on tact time calculation.

Caution
Do not use a program that has signal input or robot status
changes.
For programs that have signal input from the outside or that have changes in robot status variables or the
like, either comment out such sections or extract just the section you want to calculate the tact time for and
calculate it.
When studying the tact time for such a program, take this into account by adding an approximate input wait
time to the calculation results.

Do not use a program with an infinite loop.

The tact time for a program that falls into an infinite loop cannot be correctly calculated. Confirm that the
robot program does not fall into an infinite loop with a FOR statement or GOTO statement.

Do not use M_TIMER(1).

Do not use M_TIMER(1). This software's tact time calculation uses M_TIMER(1). If M_TIMER(1) is used
during the program, the tact time can not be calculated accurately. Change the program to use any timer
from M_TIMER(2) to M_TIMER(8) instead, then calculate the tact time.

If a position array variable or joint array variable is included, also

include the corresponding "Dim" declaration in the tact time
calculation range.
If a program whose tact time is being measured includes a position array variable or joint array variable
also include the corresponding "Dim" declaration in the tact time calculation range.

Include the destinations for any GoTo or GoSub's in the tact time
calculation range.
For example, the tact time can not be calculated for a program like the following.
The location displayed inverted in black in the program is set for tact time calculation.)

No destination selected No destination selected

for GoTo statement for sub-routine

1 xxx 1 Mov P00

: : : :
10 Mov P01 10 GoSub *SUB1
11 Mov P02 11 End
12 Mov P03 12 :
13 GoTo *L10 20 *SUB1
14 END 21 Mov P01
22 Return

13-209 13-209
13.12.2. Tact time measurement
This explains tact time measurement.

１． Start simulation.
Start simulation. For details, see "13.1 Starting a Simulation".

２． Open the program.

Open the program whose tact time you will calculate. You can calculate the tact time for "offline" and
"online" programs. However, you can not calculate the tact time for a program that has been opened in
debugging status. Always open the program with "Open
program".

For details on the operations for opening a program, see "7.2 Opening an Existing Program".

３． Specify the range for measuring the program tact time.

Drag the section to measure the program tact time for, then drag it to select it.

Figure 13-14 Tact time Measurement Range Selection

４． Click on the menu bar [Tool] -> [Tact time].

Figure 13-15 Toolbar "Tool" Menu

13-210 13-210
５． Check the range over which you will calculate the tact time.
Open the program whose tact time you will calculate. Check the contents of this range, then click the
[OK] button.

Figure 13-16 Checking the Tact time Measurement Range

The tact time calculation is started. During tact time calculation, "Calculating tact time" is displayed on
the simulation operation screen. Do not perform any other operations until this display goes out.

Status display
becomes "Tact time
measurement".

Figure 13-17 Simulation Operation Screen During Tact time Measurement

６． The tact time measurement results are displayed.

When tact time measurement is complete, the "Take time calculation results" screen is displayed. The
tact time measurement results are displayed in ms [milli seconds].

The current tact time The tact time calculation

measurement results are added
results are sequentially.
displayed. This information is cleared
when the simulation is
started again.

Figure 13-18 Tact time Measurement Results

13-211 13-211
13.12.3. Causes of tact time deviation
With this software, you can use the simulation function to calculate the robot movement tact time.
However, the calculated tact time varies with the capacity of the computer used and its load status and does not
completely match the actual robot operating time (tact time).
Use this function as a rough yardstick for tact time study.
Also, there are the following causes for the tact time calculation results deviating from actual robot tact time.

(1) An application other than "program editing" of this software is running.

This software's tact time calculation has parts that are processed on the computer in the background. For
example, if you are working running an application such as a Word document that is saved automatically, it
takes more time for the background processing for this software and sometimes the correct tact time is not
calculated. The tact time is increased.)
When calculating the tact time with this software, first close other applications.
Also, on this software itself, first close all the screens beside "Program edit".

(2) This uses commands that depend on the robot main unit status and external equipment.
There is no connection with the robot main unit or external equipment in this software's tact time calculation.
Therefore, commands that are executed communicating with that equipment are executed as if ideal
information were sent from that equipment. Therefore, the calculated cycle time is shorter than the actual
cycle time.
The commands to which this applies are shown in the following table.
Function Command Explanation
1 Positioning FINE Monitors the robot's status until it
completion wait reaches the target position.
2 Compliance CMP JNT/POS/TOOL/OFF Monitors external force on the robot.
CMPG
3 Collision detection COLCHK、COLLVL Monitors external force on the robot.
4 Servo control SERVO ON/OFF Monitors the servo amp status
For example, if the servo On command is executed in the program, the actual robot takes a few seconds,
but the simulation requires almost no time at all (500 ms or less). In order calculate the tact time precisely,
program using only movement commands and none of the above commands. If you are executing a
program you already have, either comment out such commands or extract and use just the part you want to
measure.

(3) This uses functions that depend on the CPU processing speed and OS.
The tact time calculation in this software runs on Windows, but the robot controller control software runs on
a real-time OS, so the internal operations are different. For example, with a real-time OS, the tact time may
be increased by the postponement of calculations with a high load that could not be fully processed, but in
this software's tact time calculations, such an increase in the tact time can not be calculated. Therefore, if
you use the high-load functions below, the calculated tact time may be a few percent less than the actual
tact time.
The commands to which this applies are shown in the following table.
Function Cause of increased processing on actual robot
1 CC-Link Because there is more signal processing with the CC-Link
option than without it
2 Multi tasking Because multiple robot programs are executed at the same
time
3 Added axes Because of the need to control the additional axes
4 Maximum Because the optimum movement for the robot load is
acceleration/deceleration control calculated
5 Collision detection Because processing to detect collisions is executed (*1)
6 Maintenance forecast Because the processing time is longer when the maintenance
forecasting information collection level is raised (*1)
In tact time calculation, the same results are calculated as for
information collection level 1 (the factory default setting).
(*1) On actual robots, the tact time is roughly 3-10% longer.

By changing a robot program to eliminate the above factors, you can reduce the
difference between the simulation tact time and that on the actual robot. However,
because the simulation executes the next movement command without waiting for

13-212 13-212
static determinacy after movement or for the conditions to be established, the tact
time calculated differs from the tact time on the actual robot.
We recommend that you finally confirm operation on the actual robot.

13.13. Ending Simulation

To end the simulation, close the robot program in debugging status. Then click on the menu bar [Online] →
[Offline] or click on the tool bar "Offline".

Switch to Offline.

Figure 13-19 Toolbar "Switch to Offline"

When the simulation ends, the virtual robot controller, robot view, and simulation operation screen end and
the controller goes back offline.

13-213 13-213
14. MelfaRXM.ocx Communications Middleware Setup
14.1. Summary
MelfaRXM.ocx is an ActiveX controller that communicates with CRn-500 series robot controllers.
MELFARXM.ocx can only be used if you have purchased the standard edition of RT ToolBox2. (Customers
who have purchased the mini edition can not install MELFARXM.ocx.)
When using only the RT ToolBox2 functions, there is no need to set up "MELFARXM.ocx".

Using MELFARXM.ocx enables you to simply produce Windows applications connected to a CRn-500 series
robot controller on the customer's device.

The user's manual for using MelfaRXM.ocx and the cautions are on the RT ToolBox2 standard edition CD-ROM.
This MelfaRXM.ocx is for CRn-500 series robot controllers. It can connect with CRn-700 series robot controllers, but
the only modes available for communications with robot controllers are RS-232 and Ethernet.

14.2. CD-ROM Contents

The contents of the "RT ToolBox2" (standard edition) CD-ROM are as follows.
/:

： RT ToolBox2 installation files

：

Communications
middleware This is cautions for using MELFARXM.ocx.
MelfaRXM.ocx
related file ： MelfaRXM.ocx installation files
：
This is the MELFARXM.ocx user's manual.
Figure 14-1 CD-ROM Contents

For details on MelfaRXM.ocx usage methods, refer to the user's manual on the CD-ROM.

14-214 14-214
14.3. User's Manual Reading Guide
The manual is in the CR-ROM as the Adobe PDF file.
D:/Utility/MELFARXM/Doc/MelfaRXME.pdf
* Example for the CD-ROM drive is "D:".

(1) Preparation for viewing

1) Preparing computer
Prepare a computer that has a CD-ROM drive.
2) Preparation of viewing software
Viewing requires Acrobat Reader Ver 5.0 or higher.
If neither Acrobat Reader (nor Adobe Reader) is installed, please download it from the
Adobe Systems web site. (As of December 2007)
URL: http://www.adobe.com

(2) Viewing methods

1) Starting From Windows Explorer
When you start Windows Explorer, then select the file, Acrobat Reader (or Adobe Reader)
starts and the user's manual is displayed.
2) Starting directly from Acrobat Reader (or Adobe Reader)
When you start Windows Explorer Acrobat Reader (or Adobe Reader), then select the file,
the user's manual is displayed.

14.4. Installation
Perform installation according to the following procedure

(1) Insert the program CD-ROM into the CD-ROM drive of your personal computer. Setup of “RT ToolBox2”
automatically starts. Please click “cancel”.

(2) Select [Run] from the [Start] button.

Figure 14-2 Selecting [Run]

(3) Check the drive name of the CD-ROM drive. Enter the following and click the [OK] button.
"Drive name":/Utility/MelfaRXM/Setup.exe
(If the CD-ROM drive is "D", enter "D:/Utility/MelfaRXM/Setup.exe")

Figure 14-3 [Run] Screen

14-215 14-215
(4) Installer starts and the Setup screen appears. Install according to the instructions that appear on the screen.
The Product ID is needed when this "MelfaRXM.ocx" is installed. Input the Product ID same as the Product
ID of "RT ToolBox2". "MelfaRXM.ocx" can be installed with the Product ID of standard version, but can not
be installed with mini version's.

Figure 14-4 Input Product ID

The product is installed as in "Table 14-1 Files to be Installed".

Table 14-1 Files to be Installed

No. Description Install destination
1 MelfaRXM.ocx /Windows/System folder
EZSocketRC.dll ex) Windows 2000 :/Winnt/System32
2
(communication DLL) Windows XP :/Windows/System32
NarcServerApiM.dll
3 MelfaRXM.ocx and EzSocketRC.dll are registered in the registry.
(communication DLL)

RoboCom.exe A folder specified during install operation (Normally, C:/ is used.)

4
(communication DLL) [MelfaRXM_Dev]
ReadMe.tx .............. text file which indicated notes
[RoboCom]............. folder of communication server
5 Instruction Manual [Doc]........................ folder of Instruction Manual
[Sample] ................. folder of sample programs
[BCB] ............. Borland C++ Builder (5.0)
6 Sample programs [VB] ................ Visual Basic (6.0)
[VC++] ........... Visual C++ (6.0)
[Redist]
[Installer] ....... folder of system files Installer (for redistribution)
７ Redistribution files [SysFiles] ...... folder of system files (for redistribution)

14-216 14-216
15. Appendix
15.1. Q&A
This explains frequently asked questions in a Q&A format.

1. Version

(1) Where is the software version information?

It is printed on the surface of your CD-ROM for this software.
You can also check the version information on the screen displayed with this software's menu bar [Help] →
[About RT Tool Box2 ].

(2) Where is the robot controller software version information displayed.

When this software is connected, you can check with the project tree, [Online] properties.
The version information is also displayed on the title screen for the optional teaching box.

2. Product ID

(1) Where can I check the product ID?

This software requires the product ID for installation.
The package containing your software contains a sheet of paper on which is written the product ID.
Also, after this software has been installed, you can also check the product ID on the screen displayed with
the menu bar [Help] → [About RT Tool Box2 ].

15-217 15-217
(2) I checked "About RT ToolBox2" from the menu, but the product ID is not displayed.
Is "No Product ID!" displayed?
If "No Product ID!" is displayed in the version information, the installation of this software may have failed.
Unfortunately, you need to install the software again.

3. Communications (general)

(1) What are the means for communication with the robot controller?
With a CRn-700 series robot controller, you can communicate via USB, Ethernet, and RS-232.
With a CRn-500 series robot controller, you can communicate via Ethernet and RS-232. However, when
using Ethernet with a CRn-500 series robot controller, the robot controller must have the optional Ethernet
card.
For details, see "5.1 Robots Connected and Types of Communication".

(2) Where are the communications settings made?

They are made on the project edit screen. For details, see "5.2 Connection Settings".
For the robot controller side, change the communications parameters with the optional teaching box. For
details, see "Detailed Explanation of Functions and Operations" in the robot controller's user's manual.
[Caution] The communication settings must be made on both this software and the robot controller.
If you change the robot controller settings, you must change the settings in this software too.

(3) I can not communicate with the robot controller.

If you can not communicate with the robot controller, check the following.
Also see "4. Communications (RS-232)", "5. Communications (Ethernet)", and "6. Communications
(USB)".

Check item or cause Solution

Is the connected robot controller selected Check if the correct project is selected with this software.
correctly? For details, see "4.14 Offline/Online/Simulation".
Is the robot controller power supply On? Switch On the robot controller's power supply and check
that the robot controller starts up normally.
Is Communications Server 2 running? If you closed Communications Server 2 by mistake,
Communications Server 2 is started close this software, then restart it.
automatically when this software is started.
Communication Server 2 is started as an
icon.
Are you connected to a robot controller that Check the robot controller model name in its user's
is neither the CRn-500 nor CRn-700 series? manual (or standard specifications or the like).
Are the robot controller's network settings The robot controller's network settings are made with
correct? parameters. Check the robot controller's network
settings with the optional teaching box.
Are the communications settings on this Set the correct communications settings.
software correct? For details, see "5.2 Connection Settings".
Is some other MELFA product running? Close any MELFA product other than this software.
For example is E/EN series computer For details, see "1.6 When Starting at the Same Time
support software or P/P or P/P-2 running? as Another Product".

15-218 15-218
 Check item or cause Solution
What color is Communications Server 2? The problem may be that the robot controller
Return Communications Server 2 to icon is not connected correctly. Check the items
Red
status and check the color displays for the in "(4) When Communications Server 2 is
line state. red (overall)".
The problem may be that the robot controller
and the computer have different
Green communications settings. Check the items
in "(5) When Communications Server 2 is
green (overall)".
Check the items in "(6) When
Yellow Communications Server 2 is yellow
(overall)".
Check the items in "(7) When
Light
Communications Server 2 is light blue
blue
(overall)".

(4) When Communications Server 2 is red (overall)

When Communications Server 2 is displayed red, check the following.

Check item or cause Solution

Is the communications cable connected Connect the cable correctly.
correctly?
Are you using the correct communication Check the communication cable specifications.
cable? Be careful. RS-232 cables and Ethernet cables can be
either cross cables or straight cables.
For the cable specifications, check your robot's
"Standard Specifications".
When connected with CRnQ Set the target CPU correctly.
communications, is the target CPU set For details, see "5.2.4 CRnQ Communications
correctly? Settings".

(5) When Communications Server 2 is green (overall)

When Communications Server 2 is displayed green, check the following.

Check item or cause Solution

Do the communications settings in this The communications settings in this software and on the
software and on the robot controller match? robot controller must match.
The communications settings for this software are made
on the project edit screen. For details, see "5.2
Connection Settings".
For the robot controller side, change the
communications parameters with the optional teaching
box. For details, see "Detailed Explanation of
Functions and Operations" in the robot controller's
user's manual.

(6) When Communications Server 2 is yellow (overall)

When Communications Server 2 is displayed yellow, check the following.

Check item or cause Solution

Is this software in the "Online" status? This software started up in the "Offline" status. When
you put it into "Online" status, it communicates with the
robot controller.
For details, see "4.14 Offline/Online/Simulation".

15-219 15-219
(7) When Communications Server 2 is light blue (overall)
If Communications Server 2 is displayed light blue, but communications are still not possible, check the
following.

Check item or cause Solution

Is there a communications error in this Check the contents of the communications error and
software? close the communications error window.
Is a simulation underway? End the simulation.
(Note) Only the standard edition has the
simulation function.
Is the screen server running on the End the computer's screen server.
computer?
Is the computer's hard disk is power save End computer hard disk power save mode setting.
mode?

(8) Communications with the robot controller are cut off mid-way through.
If you can not communicate with the robot controller, check the following.

Check item or cause Solution

Is the screen saver set, hard disk power off If any of these functions are running, they may cause a
set, system standby set, or system communications time-out, so do not use any of these
shut-down set? functions.
Is some other product running that uses A computer communications port can not be opened for
communications? two applications, so either close the other application or
Or is any permanent resident software change the port that this software uses.
running that uses communications?

4. Communications (RS-232)
If you can not communicate with the robot controller using RS-232, check the following.
Also, see "3. Communications (general)".

Check item or cause Solution

What color is Communications Server 2? The problem may be that the robot controller
Return Communications Server 2 to icon is not connected correctly.Check the items in
Red
status and check the color displayed for the "(1) When Communications Server 2 is
line state. red (RS-232)".
The problem may be that the robot controller
and the computer have different
Green communications settings.Check the items in
"(2) When Communications Server 2 is
green (RS-232)".

Yellow See "3. Communications (general)".

Check the items in "(3) When

Light blue Communications Server 2 is light blue
(RS-232)".

(1) When Communications Server 2 is red (RS-232)

If Communications Server 2 is displayed red with communications with the robot controller set to RS-232,
check the following.

15-220 15-220
 Check item or cause Solution
Is Communications Server 2 set for the The default value for this software is COM1. On some
correct communications port computers, COM1 is not allocated to RS-232, but to an
(COM1-COM10)? infrared port, modem, or the like. Also, when using
RS-232 over USB, the port used for RS-232 may be
other than COM1.
Use the Windows device manager or the like to check
the COM number allocated to RS-232 and change the
"Port" setting in the communications settings to that port.
Is some other product running that uses the A computer communications port can not be opened for
communication port? two applications, so either close the other application or
Or is any permanent resident software change the port that this software uses.
running that uses the communications port?
In the communications settings for this Change the communications method to RS-232.
software, is the communications method set
to TCP/IP or USB?

(2) When Communications Server 2 is green (RS-232)

If Communications Server 2 is displayed green with communications with the robot controller set to RS-232,
check the following.

Check item or cause Solution

Do the communications settings in this The communications settings in this software and on the
software and on the robot controller match? robot controller must match.
In particular, check that the protocol settings The default protocol for this software is "Procedural", but
match. for CRn-500 series robot controllers, the default protocol
is "Non-Procedural"

(3) When Communications Server 2 is light blue (RS-232)

If Communications Server 2 is displayed light blue with communications with the robot controller set to
RS-232, check the following.

Check item or cause Solution

Is anti-virus software running virus checks Switch off virus checking for RS-232.
on RS-232 communications?
When a computer starts up, sometimes this Either start the computer before connecting the cable or
generates noise. start the computer before starting the robot controller.
This noise can cause a communications
error in the robot controller.

15-221 15-221
5. Communications (Ethernet)
[Note] When using Ethernet with a CRn-500 series robot controller, the robot controller must have the optional
Ethernet card.

If you can not communicate with the robot controller using Ethernet, check the following.
Also, see "3. Communications (general)".

Check item or cause Solution

What color is Communications Server 2? The problem may be that the robot controller
Return Communications Server 2 to icon is not connected correctly.
status and check the color displayed for the Red See the items in "(1) When
line state. Communications Server 2 is red
(Ethernet)".
The problem may be that the robot controller
and the computer have different
communications settings.
Green
See the items in "(2) When
Communications Server 2 is green
(Ethernet)".
Yellow See "3. Communications (general)".
Light
See "3. Communications (general)".
blue

(1) When Communications Server 2 is red (Ethernet)

If Communications Server 2 is displayed red with communications with the robot controller set to Ethernet,
check the following.

Check item or cause Solution

In the communications settings for this Change the communications method to TCP/IP.
software, is the communications method set to
USB or RS-232?

(2) When Communications Server 2 is green (Ethernet)

If Communications Server 2 is displayed green with communications with the robot controller set to
Ethernet, check the following.

Check item or cause Solution

Are the robot controller's network settings Make the computer's network settings.
correct? Check that the IP address, gateway, subnet mask, and
other network settings are correct.
Check on the computer [Control Panel] – [Network
Settings].
* For details on the network settings, please consult
with your network administrator.
Is the robot controller's IP address set Correctly set the IP address of the robot controller
correctly in the communications settings? connected to.

15-222 15-222
6. Communications (USB)
If you can not communicate with the robot controller using USB, check the following.
Also, see "3. Communications (general)".

Check item or cause Solution

What color is Communications Server 2? The problem may be that the robot
Return Communications Server 2 to icon controller is not connected correctly.
status and check the color displayed for the Red Check the items in "(1) When
line state. Communications Server 2 is red
(RS-232)".
The problem may be that the robot
controller and the computer have different
Green
communications settings.
See "3. Communications (general)".
Yellow See "3. Communications (general)".
Check the items in "(2) When
Light
Communications Server 2 is light blue
blue
(USB)".

(1) When Communications Server 2 is red (USB)

If Communications Server 2 is displayed red with communications with the robot controller set to USB,
check the following.

Check item or cause Solution

In the communications settings for this Change the communications method to USB.
software, is the communications method set to
TCP/IP or RS-232
Is the USB driver installed? Communicating with USB requires that the USB driver
be installed.
For details, see "1.5.3 USB driver (CRnD-700 series
robot controller) installation", "1.5.4 CRnQ
communications USB driver installation" and
“1.5.5 CRnQ Communications USB driver for GOT
transparent installation”.

(2) When Communications Server 2 is light blue (USB)

With communications with the robot set to USB, if Communications Server 2 is displayed light blue, but
communications are still not possible, check the following.

Check item or cause Solution

Is the robot controller power supply Off? When connected on USB with CRnQ communications,
if the robot controller power goes Off after a normal
connection was established, the display remains light
blue.
Switch Offline with this software, switch the robot
controller power On, then go back online.
Is the communications cable connected When connected on USB with CRnQ communications,
correctly? if the communications cable is disconnected after a
normal connection was established, the display
remains light blue.
Switch Offline with this software, connect the
communications cable, then go back online.

7. Robot program

(1) Did you write the program with Movemaster commands?

15-223 15-223
 The robots that can use Movemaster commands are restricted. Check in your robot's standard
specifications to see whether it supports Movemaster commands. If your robot supports Movemaster
commands, change the language used with "6 Robot Program Language Setting" in this document

(2) Is it possible to use programs as is that we used with an E/EN series robot controller?
Position data prepared with MELFA-BASIC III (for E/EN series) can not be used as is. Convert the position
data with the "Program conversion" function. For details, see "7.11 Program Conversion".
Also, some commands have changed. For details, see "Detailed Explanation of Functions and
Operations" in the robot controller's user's manual.

(3) Is it possible to use R-250R series and R-300R series programs?

R-250R series and R-300R series robot programs written in the MELFA II language can not be used as is.
Write new programs.

8. Program edit

(1) When we check syntax, "Error in input command statement syntax" occurs frequently.

Check item or cause Solution

Is the command statement syntax correct? Program in correct syntax.
Are double-byte spaces used? Use only single-byte spaces.
Is the language to use set correctly? Set the robot program language you are using.
This software supports MELFA-BASIC IV, For details, see "6 Robot Program Language
MELFA-BASIC V, and Movemaster Setting".
commands, but there are terms that must be
switched and set for whichever one of these
you use.
Does the version of this software support your Please purchase a version that supports your robot
robot controller? controller. (Please contact the store you purchased
For some robot functions, new commands are from or one of our branches.)
added. * A program can be written to the robot controller even
if the syntax check finds many "syntax errors".

(2) How should we change the robot program language setting?

They are made on the project edit screen. For details, see "6 Robot Program Language Setting".
The robot program language set here is enabled when you edit a program offline. Online programs are
displayed in the robot program language set with the connected robot controller.

(3) When you open a program, the robot program language is different from the one set for this
project.
Is there any online program open?
Online programs are displayed in the robot program language set with the connected robot controller. The
robot program language set with the project is enabled when you edit a program offline.

(4) Is it possible to edit or copy a program that is running?

You can neither edit nor copy a program that is running. Stop the program, then edit or copy it.

(5) How should we edit a program for which the start condition is "Always"?
A program for which the start condition is "Always" is executed immediately after the robot controller power
comes On. To edit such a program, use the following procedure.
① Change the starting condition in the "Slot table (SLT * * 1-32)" parameter to "Start (normal)".
(Write this parameter to the robot controller.)

15-224 15-224
 ② Reset the power supply for the robot controller.
③ Edit the target program and save it to the robot controller.
④ Return the starting condition in the "Slot table (SLT * * 1-32)" parameter to "Always". (Write this
parameter to the robot controller.)
⑤ Reset the power supply for the robot controller.

(6) Is it possible to change the font for a robot program displayed with the program edit tool?
Yes.
Change the font used with "7.5.4 Changing the font" in this document.

(7) We are not using joint position variables (J variables), so is it possible to make the display area
smaller?
Yes.
Change the display proportions with "7.5.1 Changing the display area" in this document.

(8) Is it possible to edit a backed up program (*.MB4 file) with program editing?
It is not possible to open a backed up program (*.MB4 file) with program editing.
Restore the backed up program to a robot controller, then open it with program editing or store it on the
computer with program management.

(9) "Use defined external variable can not be used (481000000)" is displayed and the program can
not be edited.
This error is displayed if a user defined external variable is used even though the user base program is not
defined. (Normally, a user base program is defined with the "PRGUSR" parameter, but if nothing is set in the
"PRGUSR" parameter, this error occurs.)
To use a user defined external variable, define the user base program.
Also, for details on user base programs, see "Detailed Explanation of Functions and Operations" in the
robot controller's user's manual.

(10) Is it possible to copy position data to another program?

Yes.
For details, see "7.6.4.4 Copy position data" and "7.6.4.5 Pasting position data" in this document.

(11) Does it cause an error to not discriminate uppercase and lowercase letters when inputting
commands?
No.
You can input either uppercase letters or lowercase letters with the program editor, but when the program is
saved to a robot controller, the commands are converted correctly.

9. Variable monitor

(1) How are external variables (system status variables, program external variables, and user
defined external variables) monitored?
Use the program monitor.
For details, see "9.1.2 Program monitoring" in this document.

15-225 15-225
10. Option card

(1) How should one check what option cards are mounted in a robot controller?
Check from the project tree.
For details, see "11 Option Card" in this document.

11. Parameter editing

(1) No parameter list is displayed in the parameter editing tool.

Download the parameter list from the robot controller.
For details, see "8.1.3 Parameter list reading".

(2) We changed a parameter, but the new value does not take effect.
After you changed the parameter, did you switch the power for the robot controller Off, then On again?
The new parameter value does not take effect until you switch the robot controller power Off, then On again.
Switch the robot controller power Off, then On again.

12. Backup/restore

(1) Is it possible to edit a backed up program (*.MB4 file) with program editing?
It is not possible to open a backed up program (*.MB4 file) with program editing.
Restore the backed up program to a robot controller, then open it with program editing or store it on the
computer with program management.。

13. Other

(1) Characters are displayed on the screen on top of each other or with some characters missing.
Is the font size in the computer screen settings something other than "Standard"?
Use this software with the font size set to "Standard". For Windows XP, to make the screen settings, click
[Control Panel] → [Display]. Now from the "Display Properties" window "Appearance" tab, set the font size
with [Font Size].

15-226 15-226
15.2. Index
Forced output
General signal .....................................................9-146
Ａ Register (CC-Link)...............................................9-153
ABS Origin Technique ........................................ 10-159 Free Plane Limit Parameters ................................8-124
Additional Axis Parameters .................................. 8-126
Assigning Dedicated Input/Output Signals........... 8-117 Ｇ
Data parameters ................................................. 8-119
General 1 Parameters......................................... 8-117 General signal monitoring.....................................9-144
General 2 Parameters......................................... 8-117 Forced output ......................................................9-146
Hand parameters ................................................ 8-120 Pseudo-input .......................................................9-145
Jog parameters ................................................... 8-119
Machine lock (each robot) parameters................ 8-122
Servo On/Off (each robot) parameter.................. 8-122 Ｈ
Slot start (each slots) parameters ....................... 8-121 Hand Parameters .................................................8-112
Slot stop (each slots) parameters ....................... 8-121
Warm-up operation parameters .......................... 8-120
Ｉ
Ｂ Initialization.........................................................10-161
Deletion of all robot programs............................10-162
Backup............................................................... 12-197 Initializing the battery remaining time ................10-162
Breakpoint................................................. 7-95, 13-208 Serial number ....................................................10-162
Setting the time in the robot controller ...............10-161
Ｃ Install ......................................................................1-19

Collision Detection Parameters............................ 8-127

Command template................................................ 7-84 Ｊ
Communications middleware .................... 1-15, 14-218 Jog Operation .....................................................13-210
Communications Server 2...................................... 2-38 Jog Parameters .................................................... 8-111
computer cable ...................................................... 1-16 Joint position data editing .......................................7-84
Connecting with the Robot ..................................... 5-52 Jump to specified line .............................................7-82
Connection Settings............................................... 5-53
CRnQ Communications Settings .......................... 5-57
RS-232 Communication Settings .......................... 5-56 Ｍ
TCP/IP (Ethernet) Communication Settings.......... 5-54
USB Communication Settings............................... 5-54 Maintenance .......................................................10-155
Copy Maintenance Forecasting ...................................10-164
Copy position data ................................................ 7-79 Mechanical stopper technique ............................10-158
Edit assist functions .............................................. 7-79 MelfaRXM.ocx .......................................... 1-15, 14-218
Copy position data ................................................. 7-79 Menu Bar ................................................................2-35
Cut ......................................................................... 7-79 Monitoring.............................................................9-135
Errors...................................................................9-141
General signal .....................................................9-144
Ｄ Movement status .................................................9-140
Named signals.....................................................9-147
Debugging Operation hours...................................................9-154
Breakpoint............................................................. 7-95 Production information.........................................9-154
Ending debugging ................................................. 7-96 Programs .............................................................9-137
Starting debugging ................................................ 7-92 Register (CC-Link)...............................................9-150
Direct Execution................................................. 13-209 Robot status ........................................................9-143
Display area ........................................................... 7-72 Servo Monitor ....................................................10-194
Dropdown menu..................................................... 2-35 Slot operation status............................................9-136
Stop signal ...........................................................9-149
Ｅ Movement Parameters .........................................8-129
Multiple CPU Settings...........................................8-133
Error history ......................................................... 9-142
Error monitoring ................................................... 9-141
Escape Point Parameters .................................... 8-124 Ｎ
Ethernet Settings ................................................. 8-132 Named signals......................................................9-147

Ｆ Ｏ
Find Offline .....................................................................4-50
Parameters ......................................................... 8-109 Online .....................................................................4-50
Program Editing .................................................... 7-80 Operating Range Parameters............................... 8-111
Find in Files ........................................................... 7-81 Operation hour monitoring....................................9-154
Font........................................................................ 7-74 Option Card ........................................................11-195

15-227 15-227
Origin Data......................................................... 10-155 Replace ..................................................................7-82
ABS origin technique ........................................ 10-159 Restore...............................................................12-199
Mechanical stopper technique .......................... 10-158 Robot Program Language
Origin data input technique ............................... 10-157 Parameter Setting ...............................................8-125
Tool technique................................................... 10-158 Setting ...................................................................6-64
User Origin Technique ...................................... 10-159 Robot status monitoring........................................9-143
Origin data input technique ................................ 10-157 Robot view...............................................9-143, 13-205
Origin Parameter Backup................................... 10-160 RS-232 cable..........................................................1-16
Output Signal Reset Pattern Parameters..............8-116 RS-232 Setup Parameters ...................................8-123

Ｐ Ｓ
Parameter list............................................ 8-107, 8-109 Servo Monitor .....................................................10-194
Parameters .......................................................... 8-106 Load ..................................................................10-194
Find..................................................................... 8-109 Simulation..................................................4-50, 13-202
Printing................................................................ 8-134 Breakpoint .........................................................13-208
Partial writing ......................................................... 7-83 Direct Execution ................................................13-209
Paste ..................................................................... 7-79 Ending Simulation .............................................13-217
Pasting position data.............................................. 7-80 Jog Operation....................................................13-210
Position repair Function ..................................... 10-172 Robot view.........................................................13-205
Position variable Starting a Simulation .........................................13-203
Editing................................................................... 7-77 Step Operation ..................................................13-208
Production information monitoring ....................... 9-154 Tact Time Calculation ........................................13-212
Program Slot operation status monitaring ...........................9-136
Comparison ........................................................ 7-100 Slot Tables............................................................ 8-115
Copy ..................................................................... 7-98 Sorting ....................................................................7-85
Debugging ............................................................ 7-92 Start ...............................................................1-32, 2-33
Delete ................................................................... 7-99 Status bar ...............................................................2-37
Edit assist functions .............................................. 7-79 Step Operation ...................................................13-208
Move ..................................................................... 7-99 Stop signal............................................................9-149
Opening an Existing Program ............................... 7-67 Syntax check .................................................7-83, 7-90
Printing.................................................................. 7-91
Read Items ........................................................... 7-68
Rename ................................................................ 7-99 Ｔ
Robot Program Language.......................... 6-64, 8-125 Tact Time Calculation .........................................13-212
Saving Programs .................................................. 7-86 Title Bar ..................................................................2-34
Writing a New Program......................................... 7-65 Tool bar ..................................................................2-35
Writing Programs .................................................. 7-65 Tool Parameters ................................................... 8-114
Program Conversion ............................................ 7-101 Tool technique ....................................................10-158
Program Editing
Changing the display area .................................... 7-72
Character colors ................................................... 7-73 Ｕ
Command format hints.......................................... 7-73
Explanation of Program Edit screen ..................... 7-69 Uninstall..................................................................1-22
Font....................................................................... 7-74 USB Driver .......................................... 1-23, 1-25, 1-30
MELFA-BASIC IV.................................................. 7-76 User Error Parameters .........................................8-131
MELFA-BASIC V................................................... 7-75 User Origin Technique ........................................10-159
Menu Bar .............................................................. 7-70
Movemaster command ......................................... 7-76 Ｗ
Program Management ........................................... 7-97
Program monitoring ............................................. 9-137 Warm-Up Operation Parameters ..........................8-128
Program Parameters ........................................... 8-130 Weight and Size Parameters................................ 8-113
Project.................................................................... 4-41 Workspace .............................................................4-41
Adding a Project ................................................... 4-47 Changing a Workspace Name...............................4-46
Changing a Project Name..................................... 4-48 Changing a Workspace Title..................................4-46
Copying Programs Between Projects ................... 4-49 Closing a Workspace.............................................4-44
Deleting a Project ................................................. 4-48 Creating a New Workspace ...................................4-43
Project tree ................................................... 2-36, 4-49 Deleting a Workspace ...........................................4-45
Property window .................................................... 2-36 Opening an Existing Workspace............................4-44
Protect settings .................................................... 7-100 Saving a Workspace..............................................4-45
Pseudo-input Write items .............................................................7-89
General signal..................................................... 9-145
Register (CC-Link) .............................................. 9-152
Ｘ
Ｒ XYZ position data batch editing..............................7-84

Read Items ............................................................ 7-68

Register (CC-Link) monitoring ............................. 9-150 Ｚ
Forced output...................................................... 9-153
Zone Parameters..................................................8-123
Pseudo-input....................................................... 9-152
Renumbering ......................................................... 7-85

15-228 15-228
 HEAD OFFICE : MITSUBISHI DENKI BLDG MARUNOUCHI TOKYO 100-8310 TELEX : J24532 CABLE MELCO TOKYO
NAGOYA WORKS : 1-14, YADA-MINAMI 5, HIGASHI-KU, NAGOYA, JAPAN

APR.2008 MEE-BFP-A8618 Printed in Japan on recycled paper. Specifications are subject to change without notice.