Rotary Joints

Series DP – US Catalogue

NPT Threads
Rotary Joints Series DP

DP rotary joints are suitable for: axial housing connections with right-hand thread
NPT (ANSI). Axial thread with screw plug.
– hot and cold water
– modified design -750 for thermal oil Due to the low frictional moment anti-rotatio-
– Small Series also for hydraulic oil and nal devices are not required.
compressed air
– high speeds possible due to low frictional torque
– can be delivered with Atex certification

DP is available in four variants:

– DP 06, the Small Series, page 11
– DP 10 up to 50 with variation -750, page 6 to 10
– DP 65 up to 100, the Large Series, page 12 to 15
– DPN, the Stainless Steel Series, page 16 to 18

The Standard Series DP 3/8 to 2

Other advantages
– low frictional torque (important for plastic foil
production)
– long service life
– easy field repair and maintenance.
Both housing and elbow are made of brass and
are beadblasted without harm to the environment.
The bearings are protected by 5 drain holes in
the housing.
Elbows
Chrome steel rotor.
DP Rotary Joints are supplied as one way flow
Two ball bearings, factory-lubricated, maintenance- unions which can be converted to two way flow
free up to 176° F, for higher temperatures relubri- unions by using elbows:
cation through easily accessible grease point – P 2 ... for non-rotating inner pipe (with thread)
required. – PR 2 ... for rotating inner pipe (directly located
The internal mechanical seal is balanced and can in elbow)
be easily replaced with other sealing combinations. – PO 2 ... for non-rotating inner pipe, which floats
Combination 1 suitable for water up to 176° F, within the elbow and O-ring, anti-rotational
3 for water and thermal oil up to 320° F, 4 recom- protection by means of screw. Inner pipes for
mended for contaminated water, 5 for air. type PO2 are available.
– PO 2 ... -700 as PO 2, but with Viton O-ring for
Series -750 for thermal oil, equipped with heat-
thermal oil.
stabilized ball bearings, Viton O-rings and axial
shaft seal for additional bearing protection.
Drain Plug and Hose Coupling for drain holes
Connection to rotating pressure system by means of
In dusty environment we recommend to block the
– standardized connection pieces with right-hand or
drain holes with plugs to protect the seal. A drain
left-hand male thread NPT (ANSI)
hose coupling for a 1/4 inch tube (OD) shall be
– K-flange and conical inner ring (DN 11/2 and larger)
connected to the 6 o’clock position drain hole.
– fixed flange (DN 11/2 and larger), sealing with
groove and O-ring. 1 set (art.no.1190345) =
Radial housing connection with right-hand thread 4 drain plugs +
NPT (ANSI), axial with right-hand thread NPT 1 hose coupling,
(ANSI) and screw plug. For series -750 radial and suitable for all
sizes.

2 Subject to technical changes

The Large Series DP 2 1/2 to 4
The advantages of low frictional torque have
been maintained. High speeds are possible, too.
Balanced mechanical seal. The springs are situated
outside of the medium flow.
Housing made of lacquered steel. We offer 3
types of housings: for one way flow, two way
flow, non-rotating and rotating inner pipe.
The inner pipes are supported in the housing,
no elbow required.
Bearings are factory-lubricated, lubrication point
easily accessible.
Connection to the rotating pressure system
same as Standard Series. The Stainless Steel Series DPN
Radial and axial housing connection with right- The design of series DPN corresponds to that
hand female thread NPT (ANSI). of the Standard Series. DPN is suitable for appli-
cations in the food industry or for aggressive
Anti-rotation device despite low torque to media or areas. The standard design is made of
protect the hoses. 430F (1.4104) steel. For demanding applications
Set of drain plugs fits Large Series as well. a modified design type -100 is available in
316Ti (1.4571).
All other technical features same as Standard
Series. One way flow design is available with radial
(1B) or axial (1C) connection. The two way flow
design is available for non-rotating (2) or rota-
ting (R2) inner pipe. The radial connection can
be used in any position on a radius of 360°.
Ball bearings, factory-lubricated for life.
Connection to rotating pressure system by
means of standardized connection pieces with
right-hand or left-hand male thread NPT (ANSI).
Radial and axial housing connection with
right-hand female thread NPT (ANSI).
All other technical features same as Standard
Series.

The Small Series DP 1/4

Housing made of anodized aluminium. Atex
design without anodization.
Ball bearings, factory-lubricated for life.
Housing only available for one way flow with
radial connection, right-hand female thread
NPT (ANSI) or for installation into the roll
journal with axial connection.
Connection to rotating pressure system by
means of standardized connection pieces
with right-hand or left-hand male thread in
NPT (ANSI).

Subject to technical changes 3

Application Data / Ordering instructions series DP

Application Data
Series DP DP DP-750 DP DPN
Design 1, 2, R2 1B, 1C, 2, R2
Nominal diameter DN inch ...1/4 3/8...2 3/8...2 21/2...4 3/8...2
Medium compressed air
cooling water cooling water thermal oil cooling water cooling water
hot water hot water hot water hot water
hydraulic oil )*
Temperature min...max °F 14...248 14...320 32...320 14...284 14...194
Pressure PN min...max psig -3...145 -3...145 -3...145 -3...145 -3...145
Speed max...rpm 2000/DN 2000/DN 2000/DN 2000/DN
3000 2500 2500 850 2500
Avoid combination of maximum values. Higher values, other media and other threads upon request.
)* Application data for hydraulic oil: max 176°F, 1160 psi, 400 rpm

Ordering instructions Example: DP 15 R 3 1 -100

Standard and Small Series DP Page 6 to 11

Nominal diameters DN in inch (= ^ dimension A)
1/4, 3/8, 1/2, 3/4, 1, 11/4, 11/2, 2
Rotor connection
R right-hand thread
L left-hand thread
K K-flange DN 11/2 and DN 2
F fixed flange DN 11/2 and DN 2
Possible combinations of
housing connection B with rotor connection D
0 NPT K or F
1 NPT G
3 NPT NPT Other combinations upon request.
Sealing combination
1 synthetic carbon 19K – chrome steel 18E
3 metal impregnated synthetic carbon 19W – SIC 18C (silicon carbide)
4 SIC 19C – SIC 18C
5 synthetic carbon 19K – SIC 18C DP 1/4 only available with combination 5
Consecutive numbers for special designs, numbering done by factory,
-750 for thermal oil.

Ordering instructions - Elbow P Example: PO2 15 N -700

Design for inner pipe

P2 non-rotating (with right-hand thread, NPT, ANSI)
PR2 rotating
PO2 non-rotating (floating within O-ring)
Nominal diameter identical with nominal diameter of DP
Thread at connection C2
U for US size (ANSI) inner pipe and NPT thread at inner pipe
N for European size inner pipe and G thread at inner pipe
Consecutive numbers for special designs, numbering by factory,
-700 for hot oil.

4
Ordering instructions Example: DP R 2 100 L 3 4 -001

The Large Series DP 21/2 to 4 Page 12 to 15

Design for rotating inner pipe
R with slide bearing and gland seal
Number of housing connections
1 for one way flow
2 for two way flow
^
Nominal diameters DN in inch (= dimension A)
1 1
2 /2, 3, 3 /2, 4
Rotor connection
R right-hand thread
L left-hand thread
K K-flange
Possible combinations of
housing connection B with rotor connection D
0 NPT K or F
1 NPT G
3 NPT NPT Other combinations on request.
Sealing combination
1 synthetic carbon 19K – chrome steel 18E
3 metal impregnated synthetic carbon 19W – SIC 18C (silicon carbide)
4 SIC 19C – SIC 18C
Consecutive numbers for special designs, numbering by factory.

Ordering instructions Example: DPN 1B 25 R 3 3 -101

The Stainless Steel Series DPN Page 16 to 18

Number of housing connections
1B radial connection
1C axial connection
2 two way flow with fixed inner pipe
R2 two way flow with rotating inner pipe
^
Nominal diameter DN in inch (= dimension A)
3/8, 1/2, 3/4, 1, 11/4, 11/2, 2
Rotor connection
R right-hand thread
L left-hand thread
K K-flange DN 11/2 and DN 2
Possible combinations of
housing connection B with rotor connection D
0 NPT K
1 NPT G
3 NPT NPT Other combinations on request.
Sealing combination
1 synthetic carbon 19K – chrome steel 18E
3 metal impregnated synthetic carbon 19W – SIC 18C (silicon carbide)
4 SIC 19C – SIC 18C
001 Consecutive numbers for special designs in stainless steel 430 F ( 1.4104), numbering by factory.
100 Housing and rotor in stainless steel 316 Ti (1.4571).
101 Special designs in stainless steel 316 Ti (1.4571) – numbering by factory.

5
DP DN 3/8 - 2

K-flange
see page 19

Fixed flange F

DN 3/8 1/2 3/4 1 11/4 11/2 2

Type DP 10 R 31 DP 15 R 31 DP 20 R 31 DP 25 R 31 DP 32 R 31 DP 40 R 31 DP 50 R 31
Order-No. 1112050-031 1112100-031 1112150-031 1112200-031 1112250-031 1112300-031 1112350-031
Type DP 10 L 31 DP 15 L 31 DP 20 L 31 DP 25 L 31 DP 32 L 31 DP 40 L 31 DP 50 L 31
Order-No. 1112051-031 1112101-031 1112151-031 1112201-031 1112251-031 1112301-031 1112351-031
Type DP 40 K 01 DP 50 K 01
Order-No. 1112302-001 1112352-001
Type DP 40 F 01 DP 50 F 01
Order-No. 1112303-001 1112353-001

ØA 0.374 0.512 0.689 0.866 1.181 1.181 1.850

B2 (NPT) 3/8 1/2 3/4 1 1 1/4 1 1/4 2
D (NPT) 3/8 1/2 3/4 1 1 1/4 1 1/4 2
F1 3.465 3.858 4.409 5.039 6.024 6.024 7.520
F2 7.913
F3 7.559
ØJ 2.126 2.283 2.913 3.307 3.937 3.937 5.394
Ø K2 2.557 / 2.559
Ø K3 3.147 / 3.148
M 0.945 0.984 1.220 1.417 1.654 1.654 2.244
O2 0.394
O3 0.787
PG +/-0.2 1.043 0.945 1.181 1.457 1.811 1.811 2.362
U 1) 0.323 0.427 0.446 0.530 0.550 0.550 0.567
Ø AD 4.921
AZ x ø DB 5 x 0.433
JG (NPT) 1/4 3/8 1/2 3/4 1 1 1 1/2
KB 0.591
ØLK 3.937
SW 0.945 1.181 1.417 1.811 2.165 2.165 2.953
Weight (lbs) 1.8 2.2 4.0 5.3 9.9 9.9 19.8
1) approx. engagement depth (wrench tight)

6
P DN 3/8 - 2

Elbow for series DP

Type P 2 Type PR 2 Type PO 2

for non-rotating inner pipe for rotating inner pipe, directly supported for non-rotating inner pipe, floating within elbow
(with right-hand thread) in elbow and O-ring, anti-rotational protection by means
of screw. Inner pipe for type PO 2 available.

DN 3/8 1/2 3/4 1 11/4 11/2 2

Type P2 10 N P2 15 U P2 20 U P2 25 U P2 32 U P2 40 U P2 50 U
Order-No. 1112069 1112122 1112172 1112222 1112272 1112322 1112372
Type PR2 15 U PR2 20 U PR2 25 U PR2 32 U PR2 40 U PR2 50 U
Order-No. 1112123 1112173 1112223 1112273 1112323 1112373
Type PO2 10 N PO2 15 N PO2 20 N PO2 25 N PO2 32 N PO2 40 N PO2 50 N
Order-No. 1112071 1112121 1112171 1112221 1112271 1112321 1112371
C2 (NPT) 1/4 3/8 1/2 1/2 3/4 3/4 1 1/4
M 0.709 0.787 1.024 1.102 1.378 1.496 1.772
N 0.197 0.197 0.197 0.197 0.197 0.197 0.197
P+/- 0.2 1.673 1.516 2.008 2.323 2.913 3.228 3.858
ØS 0.197 0.197 0.197 0.197 0.197 0.197 0.197
V 1) 0.315 0.217 0.311 0.323 0.427 0.446 0.530
W 1 (NPT) M6x1 1/8 1/4 3/8 1/2 3/4 1
Ø W 2 (pipe) 0.370/0.371 0.495/0.496 0.619/0.621 0.743/0.745 0.994/0.996 1.243/1.245
Ø W 3 (pipe) 0.232/0.236 0.390/0.394 0.508/0.512 0.626/0.630 0.862/0.866 1.020/1.024 1.335/1.339
X 0.768 1.004 1.102 1.378 1.457 1.535
Y 0.984 0.984 1.102 1.220 1.496 1.575 1.575
Z1 1) 4.528 5.335 6.181 7.500 8.681 9.590
Z2 5.079 6.043 6.988 8.465 9.685 10.591
Z3 5.079 5.315 6.142 7.087 8.583 9.803 10.630
AG (NPT) 1/4 3/8 1/2 3/4 1 1 1/4 1 1/2
SW 0.866 0.866 1.260 1.260 1.417 1.417 2.165
WL 1.063 1.063 1.378 1.496 1.850 1.929 2.303
Weight (lbs) 0.2 0.2 0.7 0.7 1.1 1.3 2.9

Inner pipe for Elbow PO2

DN 3/8 1/2 3/4 1 11/4 11/2 2

Type ES 10 ES 15 ES 20 ES 25 ES 32 ES 40 ES 50
Order-No. 1190951 1190952 1190953 1190954 1190955 1190956 1190957

ØW4 0.233/0.236 0.390/0.394 0.507/0.512 0.626/0.630 0.861/0.866 1.019/1.024 1.332/1.339

Ø EQ 0.197 0.315 0.433 0.551 0.787 0.945 1.220
EL 6.929 7.402 7.598 9.921 10.591 11.693 13.465
LW 2.165 2.165 2.165 2.953 2.165 2.165 2.953
1) approx. engagement depth (wrench tight)
7
DP ...- 750 DN 3/8 - 2

K-flange
see page 19

Fixed flange F

DN 3/8 1/2 3/4 1 11/4 11/2 2

Type DP 10 R 33-750 DP 15 R 33-750 DP 20 R 33-750 DP 25 R 33-750 DP 32 R 33-750 DP 40 R 33-750 DP 50 R 33-750

Order-No. 1112050-750 1112100-750 1112150-750 1112200-750 1112250-750 1112300-750 1112350-750
Type DP 10 L 33-750 DP 15 L 33-750 DP 20 L 33-750 DP 25 L 33-750 DP 32 L 33-750 DP 40 L 33-750 DP 50 L 33-750
Order-No. 1112051-750 1112101-750 1112151-750 1112201-750 1112251-750 1112301-750 1112351-750
Type DP 40 K 03-750 DP 50 K 03-750
Order-No. 1112302-750 1112352-750
Type DP 40 F 03-750 DP 50 F 03-750
Order-No. 1112303-750 1112353-750

ØA 0.374 0.512 0.689 0.866 1.181 1.378 1.850

B2 (NPT) 3/8 1/2 3/4 1 1 1/4 1 1/2 2
D (NPT) 3/8 1/2 3/4 1 1 1/4 1 1/2 2
F1 3.465 3.858 4.409 5.039 6.024 6.929 7.520
F2 6.457 7.913
F3 6.693 7.559
ØJ 2.126 2.283 2.913 3.307 3.937 4.331 5.394
Ø K2 1.967 / 1.969 2.557 / 2.559
Ø K3 2.557 / 2.558 3.147 / 3.148
M 0.945 0.984 1.220 1.417 1.654 1.772 2.244
O2 0.394 0.394
O3 0.787 0.787
PG +/-0.2 1.043 0.945 1.181 1.457 1.811 2.106 2.362
U 1) 0.323 0.427 0.446 0.530 0.550 0.550 0.567
Ø AD 3.937 4.921
AZ x Ø DB 5 x 0.354 5 x 0.433
JG (NPT) 1/4 3/8 1/2 3/4 1 1 1/4 1 1/2
KB 0.591 0.591
Ø LK 3.150 3.937
SW 0.945 1.181 1.417 1.811 2.165 2.362 2.953
Weight (lbs) 1.8 2.2 4.0 5.3 9.9 13.6 19.8

1) approx. engagement depth (wrench tight)

8
P ...- 700 DN 3/8 - 2

Elbow for series DP

Type P 2 Type PR 2 Type PO 2

for non-rotating inner pipe for rotating inner pipe, directly supported for non-rotating inner pipe, floating within elbow
(with right-hand thread) in elbow and O-ring, anti-rotational protection by means
of screw. Inner pipe for type PO 2 available.

DN 3/8 1/2 3/4 1 11/4 11/2 2

Type P2 10 N P2 15 U P2 20 U P2 25 U P2 32 U P2 40 U P2 50 U
Order-No. 1112069 1112122 1112172 1112222 1112272 1112322 1112372
Type PR2 15 U PR2 20 U PR2 25 U PR2 32 U PR2 40 U PR2 50 U
Order-No. 1112123 1112173 1112223 1112273 1112323 1112373
Type PO2 10 N-700 PO2 15 N-700 PO2 20 N-700 PO2 25 N-700 PO2 32 N-700 PO2 40 N-700 PO2 50 N-700
Order-No. 1112071-700 1112121-700 1112171-700 1112221-700 1112271-700 1112321-700 1112371-700

C2 (NPT) 3/4 3/8 1/2 1/2 3/4 3/4 1 1/4

M 0.709 0.787 1.024 1.102 1.378 1.496 1.772
N 0.197 0.197 0.197 0.197 0.197 0.197 0.197
P+/- 0.2 1.673 1.516 2.008 2.323 2.913 3.228 3.858
ØS 0.197 0.197 0.197 0.197 0.197 0.197 0.197
V 1) 0.315 0.217 0.311 0.323 0.427 0.446 0.530
W 1 (NPT) M6x1 1/8 1/4 3/8 1/2 3/4 1
Ø W 2 (pipe) 0.370/0.371 0.495/0.496 0.619/0.621 0.743/0.745 0.994/0.996 1.243/1.245
Ø W 3 (pipe) 0.232/0.236 0.390/0.394 0.508/0.512 0.626/0.630 0.862/0.866 1.020/1.024 1.335/1.339
X 0.768 1.004 1.102 1.378 1.457 1.535
Y 0.984 0.984 1.102 1.220 1.496 1.575 1.575
Z1 1) 4.528 5.335 6.181 7.500 8.681 9.590
Z2 5.079 6.043 6.988 8.465 9.685 10.591
Z3 5.079 5.315 6.142 7.087 8.583 9.803 10.630
AG (NPT) 1/4 3/8 1/2 3/4 1 1 1/4 1 1/2
SW 0.866 0.866 1.260 1.260 1.417 1.417 2.165
WL 1.063 1.063 1.378 1.496 1.850 1.929 2.303
Weight (lbs) 0.2 0.2 0.7 0.7 1.1 1.3 2.9

Inner pipe for Elbow PO 2 ...-700

DN 3/8 1/2 3/4 1 11/4 11/2 2

Type ES 10 ES 15 ES 20 ES 25 ES 32 ES 40 ES 50
Order-No. 1190951 1190952 1190953 1190954 1190955 1190956 1190957
ØW4 0.233/0.236 0.390/0.394 0.507/0.512 0.626/0.630 0.861/0.866 1.019/1.024 1.332/1.339
Ø EQ 0.197 0.315 0.433 0.551 0.787 0.945 1.220
EL 6.929 7.402 7.598 9.921 10.591 11.693 13.465
LW 2.165 2.165 2.165 2.953 2.165 2.165 2.953
1) approx. engagement depth (wrench tight)
9
DP Spare Parts DN 3/8 - 2

DN 3/8 1/2 3/4 1 11/4 11/2 2

2 Housing N 1112092 1112142 1112192 1112242 1112292 1112342 1112392

8 Rotor RN 1112080 1112130 1112180 1112230 1112280 1112330 1112380
9 Rotor LN 1112081 1112131 1112181 1112231 1112281 1112331 1112381
14 Rotor K 1112336 1112386
15 Rotor F 1112337 1112387
18E Mechanical seal E 1112088-001 1112138-001 1112188-001 1112238-001 1112288-001 1112338-001 1112388-001
18C Mechanical seal C 1112088-002 1112138-002 1112188-002 1112238-002 1112288-002 1112338-002 1112388-002
19K Counter face K 3511391-001 3511392-001 3511393-001 3511394-001 3511395-001 3511396-001 3511397-001
19W Counter faceW 3511391-002 3511392-002 3511393-002 3511394-002 3511395-002 3511396-002 3511397-002
19C Counter face C 1112088-002 1112138-002 1112188-002 1112238-002 1112288-002 1112338-002 1112388-002
20 Compression spring 3511661 3511662 3511663 3511664 3511665 3511666 3511667
21 O-ring 3511809 3511866 3511721 3511929 3511947 3511886 3511696
21a O-ring 3511809-001 3511866-001 3511721-001 3511929-001 3511947-001 3511886-001 3511696-001
22 O-ring 3511860 3511867 3511861 3511862 3511863 3511864 3511865
23 Ball bearing 3510200 3510079 3510202 3510203 3510086 3510204 3510090
23a Ball bearing 3510077-010 3510079-010 3510097-010 3510082-010 3510086-010 3510087-010 3510090-010
24 Circlip 3501000 3501001 3501002 3501003 3501008 3501014 3501030
25 Circlip 3501220 3501219 3501222 3501223 3501205 3501221 3501246
26 Screw plug 3500663-004 3500662-004 3500684-004 3500621-004 3500622-004 3500623-004 3500624-004
29 O-ring 3511948 3511949
29a O-ring 3511948-001 3511949-001
30 Grease nipple 3500918 3500918 3500918 3500918 3500918 3500918 3500918
31a Shaft seal 3512325-001 3512326-001 3512327-001 3512328-001 3512329-001 3512330-001 3512331-001

Spare Parts for Elbow PO2

DN 3/8 1/2 3/4 1 11/4 11/2 2

32 O-ring 3511729 3511849 3511722 3511944 3511852 3511723 3511945

32a O-ring 3511729-001 3511849-001 3511722-001 3511944-001 3511852-001 3511723-001 3511945-001
33 Hex. screw 3500014-003 3500014-003 3500015-003 3500015-003 3500014-003 3500014-003 3500015-003
34 CU-seal 3502122-001 3502122-001 3502122-001 3502122-001 3502122-001 3502122-001 3502122-001
Pos. 31a instead of Pos. 22 upon request for additional bearing seal (a) = execution for variant -700/-750 (thermal oil)
10
DP DN 1/4 and Spare Parts

DP .. R/L 35 DN 1/4

Type DP 06 R 35
Order-No. 1112000-035
Type DP 06 L 35
Order-No. 1112001-035
Type DP 06 R -106
Order-No. 1112000-106
Type DP 06 L-106
Order-No. 1112001-106

ØA 0.256
B 1/4

D 1/4

E1 3.150
DP .. R/L -106 E2 3.504
F 2.756
ØJ 1.575
M 0.689
U 1) 0.311
GM1 2.362
GM2 1.319
LA 1.181
ØLB 0.126
SW 0.748
WZ1 1.000 +0.002
WZ2 1.640 +0.005
ZL1 2.421
ZL2 1.259 +0.010
Weight (lbs) 0.7
1) approx. engagement depth (wrench tight)

Spare Parts DN 1/4 DN 06

2 Housing N 1112042
5 Housing (-106) 1112041-058
DP .. R/L 35 DP .. R/L -106
8 Rotor RN 1112030-002
8a Rotor RN (-106) 1112030-065
9 Rotor LN 1112031-002
9a Rotor LN (-106) 1112031-065
17 Disc 3502113-001
18 Mechanical seal 3511390-001
20 Compression spring 3511521
21 O-ring 3511704-001
22 O-ring 3511906-016
23 Ball bearing 3510047
24 Circlip 3501025
25 Circlip 3501200
29 O-ring 3511868

11
DP1 DN 2 1/2 - 4

for one way flow of a medium

K-flange
see page 19

Fixed flange
DN 2½/3 Screw flange
DN 3½/4

DN 21/2 3 31/2 4

Type DP 165 R 31 DP 175 R 31 DP 180 R 31 DP 1100 R 31

Order-No. 1112400-031 1112575-031 1112450-031 1112550-031
Type DP 165 L 31 DP 175 L 31 DP 180 L 31 DP 1100 L 31
Order-No. 1112401-031 1112576-031 1112451-031 1112551-031
Type DP 165 K 01-U DP 175 K 01 DP 180 K 01-U DP 1100 K 01-U
Order-No. 1112402-001-U 1112577-001 1112452-001-U 1112552-001-U
Type DP 165 F 01 DP 175 F 01 DP 180 F 01 DP 1100 F 01
Order-No. 1112403-001 1112578-001 1112453-001 1112553-001

ØA 2.559 2.835 3.228 3.858

B2 (NPT) 2 1/2 3 3 4
D (NPT) 2 1/2 3 3 1/2 4
E 12.874 14.764 14.764 16.732
F 10.630 12.008 12.008 13.386
ØH 0.394 0.394 0.394 0.472
ØJ 7.283 8.858 8.858 10.157
ØK 4.094 4.528 4.921 5.669
Ø K2 2.837/2.839 3.434/3.437 3.931/3.933 4.427/4.429
Ø K3 3.856/3.858 4.132/4.133 4.002/4.004 4.747/4.748
M 2.461 3.346 3.346 3.937
N 5.276 5.945 5.945 6.654
O 0.748 1.181 1.000 1.000
O1 0.787 0.315 0.252 0.295
R 4.331 5.118 5.118 6.102
U 1) 0.807 0.891 0.946 0.969
Ø AD 5.709 7.283 9.000 10.866
AZ x Ø DB 5x 0.433 4x 0.709 6x 0.689 6x 0.807
AP - - 5.551 6.299
KB 1.024 0.787 0.874 0.874
LK 4.724 5.709 7.559 9.000
SW 3.346 4.331 4.331 4.724
Weight (lbs) 69.3 127.6 127.6 193.6
1) approx. engagement depth (wrench tight)

12
DP2 DN 2 1/2 - 4

for two way flow of a medium designed for non-rotating inner pipe

K-flange
see page 19

Fixed flange
DN 2½/3 Screw flange
DN 3½/4

DN 21/2 3 31/2 4

Type DP 265 R 31-U DP 275 R 31-U DP 280 R 31-U DP 2100 R 31-U

Order-No. 1112404-031-U 1112579-031-U 1112454-031-U 1112554-031-U
Type DP 265 L 31-U DP 275 L 31-U DP 280 L 31-U DP 2100 L 31-U
Order-No. 1112405-031-U 1112580-031-U 1112455-031-U 1112555-031-U
Type DP 265 K 01-U DP 275 K 01-U DP 280 K 01-U DP 2100 K 01-U
Order-No. 1112406-001-U 1112581-001-U 1112456-001-U 1112556-001-U
Type DP 265 F 01-U DP 275 F 01-U DP 280 F 01-U DP 2100 F 01-U
Order-No. 1112407-001-U 1112582-001-U 1112457-001-U 1112557-001-U

ØA 2.559 2.835 3.228 3.858

B2 (NPT) 1 1/2 2 2 2 1/2
C2 (NPSC) 1 1/2 2 2 2 1/2
D (NPT) 2 1/2 3 3 1/2 4
E 13.583 15.866 15.866 17.520
F 10.039 11.417 11.417 12.598
ØH 0.394 0.394 0.394 0.472
ØJ 7.283 8.858 8.858 10.157
ØK 4.094 4.528 4.921 5.669
Ø K2 2.837/2.839 3.434/3.437 3.931/3.933 4.427/4.429
Ø K3 3.856/3.858 4.132/4.133 4.002/4.004 4.747/4.748
M 2.461 3.346 3.346 3.937
N 5.276 5.945 5.945 6.654
O 0.748 1.181 1.000 1.000
Foto: COATEMA

O1 0,787 0.315 0.252 0.295

R 4.331 5.118 5.118 6.102
U 1) 0.807 0.891 0.946 0.969
V 1) 0.551 0.567 0.567 0.807
W (NPSC) 1 1/2 2 2 2 1/2
Z1 1) 11.575 13.283 13.283 14.980
Ø AD 5.709 7.283 9.000 10.866
AZ x Ø DB 5x 0.433 4x 0.709 6x 0.689 6x 0.807
AP - - 5.551 6.299
KB 1.024 0.787 0.874 0.874
LK 4.724 5.709 7.559 9.000
SW 3.346 4.331 4.331 4.724
Weight (lbs) 61.6 114.4 114.4 165.0
1) approx. engagement depth (wrench tight)
13
DPR2 DN 2 1/2 - 4

for two way flow of a medium designed for rotating inner pipe

K-flange
see page 19

Fixed flange
DN 2½/3 Screw flange
DN 3½/4

DN 21/2 3 31/2 4

Type DPR 265 R 31-U DPR 275 R 31-U DPR 280 R 31-U DPR 2100 R 31-U
Order-No. 1112408-031-U 1112583-031-U 1112458-031-U 1112558-031-U
Type DPR 265 L 31-U DPR 275 L 31-U DPR 280 L 31-U DPR 2100 L 31-U
Order-No. 1112409-031-U 1112584-031-U 1112459-031-U 1112559-031-U
Type DPR 265 K 01-U DPR 275 K 01-U DPR 280 K 01-U DPR 2100 K 01-U
Order-No. 1112410-001-U 1112585-001-U 1112460-001-U 1112560-001-U
Type DPR 265 F 01-U DPR 275 F 01-U DPR 280 F 01-U DPR 2100 F 01-U
Order-No. 1112411-001-U 1112586-001-U 1112461-001-U 1112561-001-U

ØA 2.559 2.835 3.228 3.858

B2 (NPT) 1 1/2 2 2 2 1/2
C2 (NPT) 1 1/2 2 2 2 1/2
D (NPT) 2 1/2 3 3 1/2 4
E 13.583 15.866 15.866 17.520
F 10.039 11.417 11.417 12.598
ØH 0.394 0.394 0.394 0.472
ØJ 7.283 8.858 8.858 10.157
ØK 4.094 4.528 4.921 5.669
Ø K2 2.837/2.839 3.434/3.437 3.931/3.933 4.427/4.429
Ø K3 3.856/3.858 4.132/4.133 4.002/4.004 4.747/4.748
M 2.461 3.346 3.346 3.937
N 5.276 5.945 5.945 6.654
O 0.748 1.181 1.000 1.000
O1 0.787 0.315 0.252 0.295
R 4.331 5.118 5.118 6.102
U 1) 0.807 0.891 0.946 0.969
Ø W2 (bushing) 1.747/1.749 2.249/2.251 2.249/2.251 2.748/2.750
X 1.500 1.500 1.500 2.000
Z2 12.524 14.217 14.217 16.173
Ø AD 5.709 7.283 9.000 10.866
AZ x Ø DB 5x 0.433 4x 0.709 6x 0.689 6x 0.807
AP - - 5.551 6.299
KB 1.024 0.787 0.874 0.874
LK 4.724 5.709 7.559 9.000
SW 3.346 4.331 4.331 4.724
Weight (lbs) 61.6 114.4 114.4 165.0
1) approx. engagement depth (wrench tight)

14
Spare Parts for types DP1, 2, R2 – DN 2 1/2 - 4

DN 3½/4

DN 2½/3

DN 21/2 3 31/2 4

1a Housing 1 N 1112445 1112495 1112495 1112545

2a Housing 2 N 1112446-061 1112496-061 1112496-061 1112546-061
4a Housing R2 N 1112447-062 1112497-062 1112497-062 1112547-062
5 Spacer 1112419 1112469 1112469 1112519
8 Rotor R N 1112430 1112605 1112480 1112530
9 Rotor L N 1112431 1112606 1112481 1112531
14 Rotor K 1112436-060 1112611 1112486-060 1112536-060
15 Rotor F 1112437 1112612 1112487 1112537
16 Fixing ring 1112415 1112465 1112465 1112515
17 Thrust collar 1112417 1112467 1112467 1112517
18E Mechanical Seal E 1112438-001 1112488-001 1112488-001 1112539-001
18C Mechanical Seal C 1112438-002 1112488-002 1112488-002 1112539-002
19K Counter Face K 3511385-001 3511386-001 3511386-001 3511388-001
19W Counter Face W 3511385-002 3511386-002 3511386-002 3511388-002
19C Counter Face C 1112438-002 1112488-002 1112488-002 1112539-002
20 Compression spring 3511550 3511551 3511551 3511551
21 O-Ring 3511708 3512553 3512553 3511828
22 O-Ring 3512553 3511828 3511828 3511815-012
23a Ball Bearing 1 3510263-006 3510103-006 3510103-006 3510144-006
23b Ball Bearing 2 3510007-006 3510208 3510208 3510145-006
24 Circlip 3501005 3501006 3501006 3501031
25 Circlip 3501253 3501238 3501238 3501247
27 Screw Flange - - 1190472-009 1190473-014
29 O-Ring 3511694 3511901 3511828 3511716
30 Lubric.nipple 3500913 3500913 3500913 3500913
31* Shaft Seal 3512358-001 3512319-001 3512319-001 3512334-001
36 Cyl.screw 3500354-070 3500354-070 3500354-070 3500354-070
37 Slide Bearing 3510546 3510549 3510549 3510548
38 Stud bolt 3500678 3500678 3500678 3500587
39 Eye bolt 3500686 3500686 3500686 3500686
*Pos.31: optional additional seal for bearing. Please specify exact type designation when inquiring or ordering.
15
DPN1 DN 3/8 - 2

for one way flow of a medium

Flanges
see page 19

DN 3/8 1/2 3/4 1 11/4 11/2 2

Type DPN 1B10 R 31 DPN 1B15 R 31 DPN 1B20 R 31 DPN 1B25 R 31 DPN 1B32 R 31 DPN 1B40 R 31 DPN 1B50 R 31
Order-No. 1113050-031 1113100-031 1113150-031 1113200-031 1113250-031 1113300-031 1113350-031
Type DPN 1B10 L 31 DPN 1B15 L 31 DPN 1B20 L 31 DPN 1B25 L 31 DPN 1B32 L 31 DPN 1B40 L 31 DPN 1B50 L 31
Order-No. 1113051-031 1113101-031 1113151-031 1113201-031 1113251-031 1113301-031 1113351-031
Type DPN 1B40 K 01 DPN 1B50 K 01
Order-No. 1113302-001 1113352-001
Type DPN 1C10 R 31 DPN 1C15 R 31 DPN 1C20 R 31 DPN 1C25 R 31 DPN 1C32 R 31 DPN 1C40 R 31 DPN 1C50 R 31
Order-No. 1113053-031 1113103-031 1113153-031 1113203-031 1113253-031 1113303-031 1113353-031
Type DPN 1C10 L 31 DPN 1C15 L 31 DPN 1C20 L 31 DPN 1C25 L 31 DPN 1C32 L 31 DPN 1C40 3 51 DPN 1C50 L 31
Order-No. 1113054-031 1113104-031 1113154-031 1113204-031 1113254-031 1113304-031 1113354-031
Type DPN 1C40 K 01 DPN 1C50 K 01
Order-No. 1113305-001 1113355-001

ØA 0.374 0.512 0.689 0.866 1.181 1.378 1.850

B (NPT) 3/8 1/2 3/4 1 1 1/4 1 1/2 2
D (NPT) 3/8 1/2 3/4 1 1 1/4 1 1/2 2
F1 3.465 3.858 4.409 5.039 6.024 6.929 7.520
F2 6.457 7.913
ØJ 2.126 2.283 2.913 3.268 3.937 4.331 5.394
Ø K2 1.967/1.969 2.557/2.559
M 0.945 0.984 1.220 1.417 1.654 1.772 2.244
O2 0.394 0.394
U 1) 0.323 0.427 0.446 0.530 0.550 0.550 0.567
PG 1.181 0.984 1.339 1.614 2.126 2.205 2.480
PG1 1.772 1.969 2.362 2.756 3.150 3.543 3.937
SW 0.945 1.181 1.417 1.811 2.165 2.362 2.953
Weight (lbs) 3.1 3.5 6.6 11.0 16.7 25.3 37.4
1) approx. engagement depth (wrench tight)

16
DPN2, DPNR2 DN 3/8 - 2

for two way flow of a medium

DPN2 for non-rotating inner pipe, DPNR2 for rotating inner pipe

Flanges
see page 19

DN 3/8 1/2 3/4 1 11/4 11/2 2

Type DPN 210 R 31 DPN 215 R 31-U DPN 220 R 31-U DPN 225 R 31-U DPN 232 R 31-U DPN 240 R 31-U DPN 250 R 31-U
Order-No. 1113060-031 1113110-031-U 1113160-031-U 1113210-031-U 1113260-031-U 1113310-031-U 1113360-031-U
Type DPN 210 L 31 DPN 215 L 31-U DPN 220 L 31-U DPN 225 L 31-U DPN 232 L 31-U DPN 240 L 31-U DPN 250 L 31-U
Order-No. 1113061-031 1113111-031-U 1113161-031-U 1113211-031-U 1113261-031-U 1113311-031-U 1113361-031-U
Type DPN 240 K 01-U DPN 250 K 01-U
Order-No. 1113312-001-U 1113362-001-U
Type DPNR 215 R 31-U DPNR 220 R 31-U DPNR 225 R 31-U DPNR 232 R 31-U DPNR 240 R 31-U DPNR 250 R 31-U
Order-No. 1113113-031-U 1113163-031-U 1113213-031-U 1113263-031-U 1113313-031-U 1113363-031-U
Type DPNR 215 L 31-U DPNR 220 L 31-U DPNR 225 L 31-U DPNR 232 L 31-U DPNR 240 L 31-U DPNR 250 L 31-U
Order-No. 1113114-031-U 1113164-031-U 1113214-031-U 1113264-031-U 1113314-031-U 1113364-031-U
Type DPNR 240 K 01-U DPNR 250 K 01-U
Order-No. 1113315-001-U 1113365-001-U

C (NPT) 1/4 3/8 1/2 1/2 3/4 3/4 1 1/4

M 0.709 0.787 1.024 1.102 1.378 1.496 1.772
P 1.673 1.516 2.008 2.323 2.913 3.228 3.858
V 1) 0.315 0.217 0.311 0.323 0.427 0.446 0.530
W1 (NPT) M 6x1 1/8 1/4 3/8 1/2 3/4 1
W2 (bushing) 0.370/0.371 0.495/0.496 0.619/0.621 0.744/0.746 0.994/0.996 1.243/1.245
X 0.768 1.004 1.122 1.378 1.457 1.535
Z1 1) 4.409 4.532 5.354 6.197 7.504 8.682 9.593
Z2 5.079 6.043 6.988 8.465 9.685 10.591
PG2 2.126 1.969 2.638 2.953 3.622 3.937 4.921
WL 1.063 1.063 1.378 1.496 1.850 1.929 2.303
Weight (lbs) 3.3 4.0 8.1 12.5 18.9 29.7 44.0
1) approx. engagement depth (wrench tight)

17
Spare Parts for types DPN1, 2, R2 – DN 3/8 - 2

DN 3/8 1/2 3/4 1 11/4 11/2 2

1 Housing N 1112092-245 1112142-245 1112192-245 1112242-245 1112292-245 1112342-245 1112392-245

1 a Housing N 1112092-246 1112142-246 1112192-246 1112242-246 1112292-246 1112342-246 1112392-246
2 Cover 1112095-208 1112145-208 1112195-208 1112245-208 1112295-208 1112345-208 1112395-208
2 a Cover 1112095-206 1112145-206 1112195-206 1112245-206 1112295-206 1112345-206 1112395-206
3 Housing connection N 1112094-247 1112144-247 1112194-247 1112244-247 1112294-247 1112344-247 1112394-247
3 a Housing connection N 1112094-248 1112144-248 1112194-248 1112244-248 1112294-248 1112344-248 1112394-248
4 Elbow P2 U 1112069-249 1112122-249 1112172-249 1112222-249 1112272-249 1112322-249 1112372-249
4 a Elbow P2 U 1112069-250 1112122-250 1112172-250 1112222-250 1112272-250 1112322-250 1112372-250
5 Elbow PR2 U 1112123-251 1112173-251 1112223-251 1112273-251 1112323-251 1112373-251
5 a Elbow PR2 U 1112123-252 1112173-252 1112223-252 1112273-252 1112323-252 1112373-252
5-1 Bushing 3510541 3510542 3510543 3510544 3510537 3510512
6 Rotor RN 1112080 1112130 1112180 1112230 1112280 1112330 1112380
6 a Rotor RN 1112080-171 1112130-171 1112180-171 1112230-171 1112280-171 1112330-171 1112380-097
7 Rotor LN 1112081 1112131 1112181 1112231 1112281 1112331 1112381
7 a Rotor LN 1112081-171 1112131-171 1112181-171 1112231-171 1112281-171 1112331-171 1112381-097
14 Rotor K 1112336 1112386
14 a Rotor K 1112336-163 1112386-163
18 Mechanical seal E 1112088-001 1112138-001 1112188-001 1112238-001 1112288-001 1112338-001 1112388-001
18 Mechanical seal C 1112088-002 1112138-002 1112188-002 1112238-002 1112288-002 1112338-002 1112388-002
18 a Mechanical seal C 1112088-159 1112138-159 1112188-077 1112238-081 1112288-159 1112338-159 1112388-159
19 K Counter face K 3511391-001 3511392-001 3511393-001 3511394-001 3511395-001 3511396-001 3511397-001
19 W Counter face W 3511391-002 3511392-002 3511393-002 3511394-002 3511395-002 3511396-002 3511397-002
19 C Counter face C 1112088-002 1112138-002 1112188-002 1112238-002 1112288-002 1112338-002 1112388-002
20 Compression spring 3511661 3511662 3511663 3511664 3511665 3511666 3511667
20 a Compression spring 3511661-001 3511662-001 3511663-001 3511664-001 3511665-001 3511666-001 3511667-001
21 O-ring 3511809 3511866 3511721 3511929 3511947 3511886 3511696
23 Ball bearing 3510200-008 3510079-008 3510097-008 3510148 3510086-008 3510087-008 3510090-008
24 Circlip 3501000-001 3501001-001 3501002-001 3501003-001 3501008-001 3501027 3501030-001
25 Circlip 3501220-001 3501219-001 3501222-001 3501223-001 3501205-001 3501241 3501246-001
26 Screw plug 3513598-001 3513599-001 3513600-001 3513601-001 3513602-001 3513603-001 3513604-001
31 Shaft seal 3512325-001 3512326-001 3512327-001 3512328-001 3512329-001 3512330-001 3512331-001
33 Set screw 3500576-002 3500576-002 3500516-002 3500516-002 3500534-002 3500534-002 3500586-002
34 Set screw 3502163-002 3502163-002 3500591-002 3500591-002 3500533-002 3500533-002 3500592-002
35 O-ring 3511852 3512521 3511754 3511713 3511942 3512540 3512503
Execution “a” for variant -100. Please specifiy exact designation when inquiring or placing orders!
18
Journal Flanges for K Rotor Connection

2
DN K-flange Order-No. Inner ring Order-No. Flat pack. Ø A Ø AD Ø LK AZ x Ø KD Ø ID KB Ø K2 O EB
Order-No. Ø DB Pilot hole
1 1/2 KF 40-0 1190435 IR 40-0 1190405 3512235 1.378 4.134 3.150 4x 0.433 2.087 1.889/ 0.591 1.969/ 0.394 0.630
1.891 1.970
2 KF 50-0 1190436 IR50-0 1190406 3512236 1.850 5.118 3.937 4x 0.551 2.717 2.480/ 0.591 2.559/ 0.394 0.630
2.482 2.561
2 1/2 KF 65-700 1190437-700 IR 65-700 1190407-700 3512237-700 2.559 5.827 4.764 4x 0.571 3.504 2.742/ 1.024 2.841/ 0.748 1.102
2.744 2.843
3 KF 75-0 1190440 IR 75-0 1190420 1190191-058 2.835 7.992 6.752 5x 0.689 3.504 3.315/ 1.220 3.437/ 0.874 1.339
3.317 3.439
3 1/2 KF 80-700 1190438-700 IR 80-700 1190408-700 3512238-700 3.228 8.504 7.008 6x 0.689 4.291 3.799/ 1.260 3.937/ 1 1.378
3.803 3.939
4 KF 100-700 1190439-700 IR 100-700 1190409-700 3512239-700 3.858 8.976 7.520 6x 0.689 4.724 4.295/ 1.378 4.433/ 1 1.496
4.299 4.435

19
 D 13209 us

Christian Maier GmbH & Co. KG Branch Offices & Service Stations:
Maschinenfabrik
Maier America LLC
Wuerzburger Straße 67-69
D-89520 Heidenheim 6669 Peachtree Industrial Blvd., Suite L / M
Norcross, GA 30092 - USA

P.O.Box 1609
D-89506 Heidenheim + 1-770-409 0022
 + 49 (0) 73 21 / 317-0 + 1-770-409 0069


+ 49 (0) 73 21 / 317-139 (Export) [email protected]
0 800 / 7 51 82 50 www.maieramerica.com
+ 49 (0) 73 21 / 317-239
[email protected]
Maier Italia Srl
www.maier-heidenheim.de
Via Enrico Toti 3
I-21040 Gerenzano (VA)
 + 39-02-96 24 82 88
+ 39-02-96 36 96 95
[email protected]
www.maier-italia.com