See discussions, stats, and author profiles for this publication at: https://www.researchgate.

net/publication/294457323

Optimization of continuous casting process in steel manufacturing industry

Conference Paper · August 2014

CITATIONS READS

0 1,688

1 author:

Muhammad Iqbal Hussain

Universiti Malaysia Perlis
35 PUBLICATIONS   26 CITATIONS   

SEE PROFILE

Some of the authors of this publication are also working on these related projects:

foreign material defect for composite material View project

manufacturing View project

All content following this page was uploaded by Muhammad Iqbal Hussain on 15 February 2016.

The user has requested enhancement of the downloaded file.

 Scientific Cooperations International Workshops on Engineering Branches
8-9 August 2014, Koc University, ISTANBUL/TURKEY

Optimization of continuous casting process in steel

manufacturing industry
Muhammad Iqbal Hussain Zuraidah Mohd Zain
School of Manufacturing Engineering. School of Manufacturing Engineering.
Universiti Malaysia,Perlis Universiti Malaysia,Perlis
Kangar Perlis Malaysia Kangar Perlis Malaysia
[email protected] [email protected]

NG. Hooi. Xian

School of Manufacturing Engineering.
Universiti Malaysia,Perlis
Kangar Perlis Malaysia
[email protected]

Abstract— The continuous casting process is used for Hence there is a growing need to understand the causes of
solidifying molten steel into semi-finished steel. The defects occurring in the continuous casting process to improve
technology for Secondary Cooling Zone (SCZ) is extremely casting conditions for production of high quality billets, thus
important for output of casting machine and billet quality. increasing yield production, reducing wastages and energy
Occurrences of internal defects e.g. edge cracks commonly consumption in return for higher profit to the company [1].
known as diagonal cracks in the continuous cast product of
steel Grade H is commonly related to the uniformity of the The research improvement concentrates on the finding out the
water flow rate control in SCZ. Design of Experiment, DOE is causes of diagonal cracks which commonly occurs during the
used in analyzing the parameters that influences the quality of casting process in the Continuous Casting Machine (CCM).
the billet production; Secondary Zone 1st sector water flow The casting process is the most important and critical process
nd
rate, Secondary Zone 2 sector water flow rate and Secondary whereby the molten steel will be cast out through a copper
rd
Zone 3 sector water flow rate. The optimum results are mould while passing through a series of cooling sections to
attained to achieve the best combination of parameters value maintain the shape and size of the billets. The crack of the
to be used in continuous casting process. continuous casting billet is a fatal defect which may be cause
by various different reasons. In this study, series of
st
Keywords: diagonal cracks, DOE, secondary zone 1 sector water experiments are carried out with the aid of Design Expert,
flow rate, secondary zone 2nd sector water flow rate, secondary zone Design of Experiment (DOE) software to determine the
3rd sector water flow rate. processing parameters in reducing and avoiding the formation
1. Introduction
of such cracks.
Billet is a semi-finished steel product produced out from 1.2. Problem Statement
different types of scrap metals for the used in construction site Diagonal cracks are defects which are regularly occurring
as well as to fulfil needs in other secondary processes, e.g. through strands the 6-strand after being cast out from the
rolling or forging into finished product, e.g. round bar, casting machines. The occurrence of such defect tends to
deformed bar or wire rod in coil forms. Today in the lower the yield production thus leading to loss in profit and
modernized world, the demand for billets continues to rise. material wastage. The presumed parameters influencing such

305
 Scientific Cooperations International Workshops on Engineering Branches
8-9 August 2014, Koc University, ISTANBUL/TURKEY

defect maybe due to the secondary 1st, 2nd and 3rd sector water
flow rate. For that reason, investigation is carried out to attain
and achieve the actual and ideal process requirement in the
CCM.

1.3. Research Objective

Among the objectives for this study:-
(1) To study and identify the effects of secondary zone 1st, 2nd
and 3rd sector water flow rate during casting process.
(2) To ascertain and discover the optimum settings for the
Fig.1.1, The continuous casting process.
secondary zone 1st, 2nd and 3rd sector water flow rate
during casting process. 1.5. Diagonal Crack
Diagonal crack is a main concern as it occurs frequently
1.4. The Basic Principles of Continuous during production of Grade H billets. Diagonal cracks arise as
Casting Machine (CCM) a result of bulging of the narrow and broad faces due to lack of
The CCM facility in company M is a 6-strand caster used to support, and also where the strand shell case undergoes
produce “semi-finished” billets. The objective of this section rhombic distortion (rhomboidity). Even in cases where there is
is primarily to cast the molten steel into billet. Figure 1.1 [2] a perfect mould taper and properly aligned foot rolls, uneven
shows an example of the bow type caster found in most steel strand cooling in secondary cooling zone of billet caster can
mills. Once the required metallurgical composition or grade of cause rhomboidity. Although several studies suggested that
steel is achieved at a certain temperature of 1590oC-1600oC, cracks are related to rhomboid condition of the billet [3-7],
the molten steel is then transferred via nozzle into a ladle. this crack can also occur due to absence of rhomboid, due to
When the ladle filled with molten steel is in the casting improper corner radius [3, 8], or mould distortion and wear [4,
position, the slide gate is opened and the molten steel is 5].
transferred to the tundish via a long nozzle. A stopper rod is
located at the bottom of the tundish which controls the flow
rate of the molten steel into the mould. The tundish acts as a
pool containing the liquid steel which feeds liquid steel to the
mould at a regulated rate. The tundish allows continuous
feeding of molten steel to the mould during ladle exchanges.

Fig. 1.2, Sample of cross-sectional area of a billet which

shows diagonal crack.

306
 Scientific Cooperations International Workshops on Engineering Branches
8-9 August 2014, Koc University, ISTANBUL/TURKEY

Table 1.1, Summary of the analysis for diagonal crack. The experiment conducted using Design-Expert software, is
Defect  Easily detectable rhomboidity by thoroughly analysed to investigate the three factors
identification measuring the diagonal.
Possible Causes  Non-uniform PCZ or at the mould influencing the experiment response. Optimization is carried
exit area or at SCZ. out after analysis to obtain the most optimum parameter using
 Guide rolls not aligned
numerical, graphical or point prediction tools offered by the
Other Associated  Deformed mould tube or with
Causes deposits on the outer surface. Design-Expert software.
 Too high steel tapping temperature.
 Incorrect mould geometry.
Suggested  Check alignment between mould and Based on the optimum settings generated by Design-Expert
Remedies guide rolls. software for minimum goal of diagonal crack at moderate high
 Check position and efficiency of
spraying nozzles. level of importance is water flow rate (1st sector) =
 Replace mould tube 407.39l/min, water flow rate (2nd sector) = 326.12l/min and
Solution by  To conduct preventive maintenance
conditioning water flow rate (3rd sector) = 68.02l/min. The optimum
frequently according to production
schedule. condition represents the combinations/setting of factor levels
Possible Effects  Cracks in the sub skin area up to that is expected to produce the best performance. The 3D
on Rolled product 5mm can create defects on hot rolled
products. surface graph result produced by Design-Expert software is
 Rhomboidity higher than 5% can shown in Figure 1.3.
create problems on hot rolling.

1.6. Statistical Design of Experiment (DOE)

Once DOE method has been chosen as the primary method for
research study, the data collected is analyzed accordingly.
The three factors are set with its high and low values to build
and determine the range of each level.
Table 1.2, Levels for Design Factors.
Design Factors Levels
Low High
st
Secondary 1 Sector Water 400 432
Flow Rate, l/min
Fig. 1.3, 3D Surface Graph based on the model’s desirability
Secondary 2nd Sector Water 326 350 on diagonal crack.
Flow Rate, l/min
Figure 1.3 shows 3D Surface Graph for the factors A and B in
Secondary 3rd Sector Water 68 80
the model. It estimates the performance at optimum condition.
Flow Rate, l/min
Notice how it flattens as the desirability is achieved. This is a
region of stability for minimum diagonal crack response.
In this research study, a Full Two-Level Factorial Design, 2k is
chosen toward the consideration of the criterion of the
research study. A full factorial design considers all plausible
combinations of the design factors and levels.

1.7. Result

307
 Scientific Cooperations International Workshops on Engineering Branches
8-9 August 2014, Koc University, ISTANBUL/TURKEY

[5] H. Mori, “Causes and Prevention of Defects in

Continuous Casting. Pt.1” Tetsu-to-Hagane (J. Iron
Steel Inst. Jpn.) Vol.58 (10), 1972, 1511-1525.
[6] W.P. Young and W.T. Whitfield, “Casting of Quality
Steel at Wisconsin Steel”, 51ST National Open Hearth
and Basic Oxygen Steel Conference, AIME, New
York, Vol. 51, 1968, 127-132.
[7] K. Matsunaga, Y. Ohkita, S. Hirayama, S. Kimiya,
S. Kojima, ”Progress in the Continuous-Strand
Casting of Billets at Kokura Steel Works of Sumitomo
Metals (Retroactive Coverage)”, 59th National Open
Hearth and Basic Oxygen Steel Conference, (St.
Louis Mo.), Metallurgical Society AIME, New York,
N.Y., 1976, 228-249.
[8] Y. Aketa and K. Ushijima, Tetsu-to-Hagane (J. Iron
Fig. 1.4, Overlay plot produced by Graphical Optimization. Steel Inst. Jpn.) Vol. 45 1959, 1314-1345.

Graphical Optimization presents the area of feasible response

values in the factor space. Through the graph, a visual search
is carry out in search for the best compromise. Yellow region
is the area that satisfies the constraint evaluated; on the other
hand, gray region is the area which does not meet the required
criteria. The flag ‘pointed’ in Figure 1.4 depicts the area of
feasible response for the model in accordance to the optimum
settings evaluated in Figure 1.3.

1.8. Conclusion
With the aid of Design Expert Software, optimization is
carried to discover a range of optimum setting for secondary
zone 1st, 2nd and 3rd sector water flow rate. By using the range
of optimum settings generated by Design Expert Software, it
is known that there’s a slight decrease in the numbers of billets
rejected from 359 to 321 billets (reduction of 8.5%) and from
321 to 311 billets (reduction of 3.1%).
1.9. References
[1] Hans F. Schrewe, Continuous Casting of Steel-
Fundamentals Principles and Practice, 1987,
Stahleisen.
[2] F.R. Camisani-Calzohari, I.K. Craig, P.C. Pistorius,
“Control strategies for the secondary cooling zone in
continuous casting”, IEEE, 1999.
[3] I.V Samarasekera and J.K. Brimcombe, “The
influence of Mold Behaviour on the production of
Continuously Cast Steel Billets,” Metallurgical
Transaction B, Vol. 13B (1), 1982, 105-116.
[4] V.P. Perminov, N.M. Lapotyshkin, V.E. Girskii, A.I.
Chizhikov, “Prevention of Distortion in A
Continuously-Cast Square Alloy Steel Billet”, Stal. In
English, Vol.7, 1968, 560-563.

308

View publication stats