Scribd
Upload
185 views

Stellite 12

Uploaded by

xy2zjg
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
185 views

Stellite 12

Uploaded by

xy2zjg
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

STELLITE 12 ALLOY

STELLITE 12 TM

T EC H NI CA L DATA

TIG & OXY-ACETYLENE WELDING | MMA WELD DEPOSITION | MIG WELD DEPOSITION | PTA & LASER WELD DEPOSITION | HVOF & PLASMA SPRAY DEPOSITION

Nominal Composition (mass %) and Physical Properties

Co Cr W C Others Hardness Density Melting Range

3
Base 27-32 7.5-9.5 1.4-1.7 (hardfacings) Ni, Fe, 45-51 HRC 8.53 g/cm 2192-2489 ºF
1.7-2.0 (castings) Si, Mn 435-590 HV 0.308 lb/in 3 1200-1365 ºC

Stellite cobalt base alloys consist of complex carbides in an alloy


TM

matrix. They are resistant to wear, galling and corrosion and retain
these properties at high temperatures. Their exceptional wear
resistance is due mainly to the unique inherent characteristics of
the hard carbide phase dispersed in a CoCr alloy matrix.

Stellite 12 could be considered an intermediate alloy between


TM

Stellite 6 and Stellite 1. It contains a higher fraction of hard,


TM TM

brittle carbides than Stellite 6, and has increased resistance


TM

to lowangle erosion, abrasion, and severe sliding wear whilst


retaining reasonable impact and cavitation resistance. Stellite TM

12 is often used self-mated or running against Stellite 6 or TM

Stellite 1. The higher tungsten content provides better high-


TM

temperature properties compared to Stellite 6, and it can be


TM

used at temperatures up to about 700˚C.


TM
Optical Micrograph of a Stellite 12 PTA Deposit at 500X.

Stellite 12 is typically used for cutting tools that need to


TM Corrosion Resistance
withstand abrasion, heat and corrosion. Examples include The typical electrode potential in sea water at room temperature
industrial knives for cutting carpets, plastics, paper and synthetic is approximately -0.3 V (SCE). Like stainless steels, Stellite 12 TM

fibres; and saw tips in the timber industry. It is also used for corrodes primarily by a pitting mechanism and not by general
control plates in the beverage industry, pump vanes, bearing mass loss in seawater and chloride solutions. Information
bushes and narrowneck glass mold plungers; and for hardfacing regarding corrosion resistance in other corrosive environments
of engine valves, pinch rollers in the metal-processing industries, can be provided on request.
and rotor blade edges.

www.kennametal.com/stellite
STELLITE 12 ALLOY
tm

T EC H NI CA L DATA

Nominal Thermal Expansion Coefficient (from 20°C to stated temperature)

100°C 200°C 300°C 400°C 500°C 600°C 700°C 800°C 900°C 1000°C
(212°F) (392°F) (572°F) (752°F) (932°F) (1112°F) (1292°F) (1472°F) (1652°F) (1832°F)

µm/m.K 11.5 12.1 12.6 12.9 13.3 13.8 14.3 14.8 15.2 15.6

µ-inch/inch.°F 6.4 6.7 7.0 7.2 7.4 7.7 7.95 8.2 8.45 8.7

Nominal Tensile Properties at Room Temperature


Ultimate Tensile Strength Rm Yield Stress Rp(0.2%) Elongation Elastic Modulus

ksi MPa ksi MPa A(%) psi GPa


6
Castings 107 740 84 580 <1 32.8x10 226
Stellite HS-12 (*) 174 1200 130 900 2 30.1x106 208
(*) "HS" = HIP-consolidated from the powder form

Nominal Hot Hardness (DPH) as-cast

20°C 100°C 200°C 300°C 400°C 500°C 600°C 700°C 800°C 900°C
(68°F) (212°F) (392°F) (572°F) (752°F) (932°F) (1112°F) (1292°F) (1472°F) (1652°F)

546 456 418 390 380 371 362 328 232 153

Thermal and Electrical Properties Product Forms and Cross Reference Specifications

Stellite 12 is available as welding wire, rod, powder, and


TM

Approximate value at Room Temperature


electrodes; finished castings and P/M parts. Kennametal
Thermal conductivity 14.6 W/m.K 100 Btu-in/hr/ft2/°F Stellite also offers hardfacing services.
Electrical resistivity 98 µ-ohm.cm 38.6 µ-ohm.cm
Stellite 12 can be supplied to the following specifications:
TM

Specification Product Form Specification Product Form

AWS A5.21 / ASME BPVC IIC SF Rod


UNS R30012 Rod, Casting A 5.21 ERCoCr-B

UNS W73012 Electrode AWS A5.21 / ASME BPVC IIC SF Wire


A 5.21 ERCCoCr-B
AWS A5.13 / ASME BPVC IIC SF Electrode
UNS W73042 Wire
A 5.13 ECoCr-B

Kennametal Stellitetm manufactures sophisticated alloys in the form of castings, powders, coatings, consumables, and machined parts that resist wear, corrosion, and abrasion.
Information provided in this document is intended only for general guidance about Kennametal Stellitetm products and is the best information in our possession at the time.
Product users may request information about their individual use of our products, but Kennametal Stellitetm does not warrant or guarantee this information in any way. Selection
and purchase of Kennametal Stellitetm products is the sole responsibility of the product user based on the suitability of each use. Individual applications must be fully evaluated by
the user, including compliance with applicable laws, regulations, and non-infringement. Kennametal Stellitetm cannot know or anticipate the many variables that affect individual
product use and individual performance results may vary. For these reasons, Kennametal Stellitetm does not warrant or guarantee advice or information in this document, assumes
no liability regarding the same, and expressly disclaims any warranty of any kind, including any warranty of fitness for a particular purpose, regarding the same.

EU ROPE A N S A L E S OFFI C E S A MER I C A S S A L E S OFF I C E


Kennametal Stellite Kennametal Stellite Kennametal Stellite Kennametal Stellite
Unit 3, Birch Zur Bergpflege 51 – 53 Via G. Di Vittorio, 24 1201 Eisenhower Drive N
Kembrey Business Park 56070 Koblenz 20090 Pieve Emanuele Goshen, Indiana 46526
Swindon SN2 8UU Germany Milan USA
UK Phone: 49.261.80.88.0 Italy Phone: 1.574.534.2585
Phone: 44.1793.498500 Fax: 49.261.80.88.35 Phone: 39.02.907871 Fax: 1.574.534.3417
Fax: 44.1793.498501 Fax: 39.02.90787 231
E-mail: [email protected] E-mail: [email protected] www.kennametal.com/stellite
©2013 Kennametal Inc. l All rights reserved. l B-13-03109

You might also like