H3D-M SAFETY PRECAUTION This manual uses the following symbols to ensure safe operation of this timer.
MULTI-FUNCTION ANALOGUE TIMER WARNING Warnings are indicated when mishandling this product might result in death or serious injury to user.
User's Manual CAUTION Cautions are indicated when mishandling this product might result in minor injury to the user, or only physical damage to the timer.
WARNING
‧Note this incorrect wiring of this product can damage it and lead to other hazards. Make sure the product has been correctly wired before turning the power
ON.
RESTRICTIONS ON USE ‧Before wiring, or removing / mounting the product, be sure to turn the power OFF. Failure to do so might cause electric shock.
When using this product in applications that require ‧Do not touch electrically charged parts such as the power terminals. Doing so might cause electric shock.
particular safety or when using this product in ‧Do not disassemble the product. Doing so might cause electric shock or faulty operation.
important facilities, please pay attention to the safety
of the overall system and equipment. Install fail-safe CAUTION
mechanisms, perform redundancy checks and periodic ‧Use the product within the operating ranges recommended in the specification (temperature, humidity, voltage, shock, mounting direction, atmosphere and
inspections and adopt other appropriate safety etc.). Failure to do so might cause fire or faulty operation.
measures when it is necessary. This product is rated at ‧Firmly tighten the wires to the terminal. Insufficient tightening of the wires to the socket might cause fire.
Class Ⅱ .
SPECIFICATIONS FACEPLATE
Operating voltage AC: 24~240V, DC: 12~240V
Allowable operating
voltage range 90 ~ 110% of rated operating voltage A1 15 Y1
Rated frequency 50 / 60Hz Power LED: 100m
10h 100h Range:
Range
ON : Supply voltage applied 10m 1s, 10s, 100s, 10m, 100m, 10h, 100h at Full Scale
Contact rating 250VAC 8A (Resistive load) 100s
10s 1s
OFF : No Supply voltage PW
8 10
Reset time MAX 0.1s 6
Flashing : During timing Time
4 Time:
2 0
Power consumption Approx. 1.9VA OUT
E J1
0 ~ Full Scale adjustment
D1
D
Life Mechanical : 5,000,000 times / Electrical : 100,000 times Mode
B2
B A
o Output LED: H3D-M Mode:
Ambient temperature -10～+50 C 18 16 A2
ON : Output relay energized Timing mode selection
Ambient humidity MAX 85% RH OFF : Output relay de-energized
Weight Approximatly 62g
TIMING CHART
Mode A: On-delay, Mode B: Flasher starting with OFF, Mode B2: Flasher starting with ON,
Timing starts when supply voltage is applied to Timing starts when supply voltage is applied to Timing starts when supply voltage is applied to
A1-A2. When the timing completes, the output A1-A2. The timing cycle starts with an OFF time, A1-A2. The timing cycle starts with an ON time,
relay energizes. Interrupting supply voltage then changes to ON time of equal length and then changes to OFF time of equal length and
resets the timing. continues the OFF-ON cycle until the supply continues the ON-OFF cycle until the supply
voltage is interrupted. voltage is interrupted.
t <t t t t t
SOURCE (A1-A2) SOURCE (A1-A2) SOURCE (A1-A2)
N.C. (15-16) N.C. (15-16) N.C. (15-16)
N.O. (15-18) N.O. (15-18) N.O. (15-18)
Output LED Output LED Output LED
Power LED Power LED Power LED
*The control contact A1-Y1 is without function in this mode. *The control contact A1-Y1 is without function in this mode. *The control contact A1-Y1 is without function in this mode.
Mode D: Control contact OFF-delay, Mode D1: Trailing edge interval, 1 Mode E: Interval, 1
With supply voltage applied at A1-A2, when the With supply voltage applied at A1-A2, when the Timing starts and the output relay energizes
control contact A1-Y1 is held closed, the output control contact A1-Y1 is opened, the timing when supply voltage is applied to A1-A2. When
relay energizes. When the contact is opened, starts and the output relay energizes. When the the timing completes, the output relay
the timing starts. When the timing completes, timing completes, the output relay de-energizes. de-energizes. Interrupting supply voltage resets
the output relay de-energizes. Closing A1-Y1 Closing A1-Y1 during timing de-energizes the the timing.
during timing resets the timing. output relay and resets the timing.
t t t <t
SOURCE (A1-A2) SOURCE (A1-A2) SOURCE (A1-A2)
CONTROL (A1-Y1) CONTROL (A1-Y1) N.C. (15-16)
N.C. (15-16) N.C. (15-16) N.O. (15-18)
N.O. (15-18) N.O. (15-18) Output LED
Output LED Output LED Power LED
Power LED Power LED
*The control contact A1-Y1 is without function in this mode.
Mode J1: Single shot, 1 CONNECTION DIMENSION(mm)
With supply voltage applied at A1-A2, timing
starts by closing control contact A1-Y1 and
output relay energizes during the timing. When 17.5 60
the timing completes, the output relay de- 43 5.0
A1 15 Y1
energizes. After completion, closing A1-Y1
A1 (L/+)
restarts timing. Operating A1-Y1 during timing or
holding it closed has no effect. Y1 15
t t
71.2
45
SOURCE (A1-A2)
16 18
CONTROL (A1-Y1)
A2 (N/-)
N.C. (15-16)
18 16 A2
N.O. (15-18)
Output LED
Power LED
ANLY ELECTRONICS CO., LTD. M-H3DM-M-A
P r oduct is su bje ct to ch ange wit hout not ic e.
http://www.anly.com.tw Printed in Taiwan
