ELECTRICAL

DESIGN 1
THIS COURSE DEA
INSTALLATION AND CO
LS WITH THE STUDY OF ELECTRICAL SYSTEM DESIGN,
ST ESTIMATION FOR SINGLE AND MULTI-FAMILY DWELLING
UNITS GUIDED BY THE PROVISIONS OF THE PHILIPPINE ELECTRICAL CODE (PEC)
AND OTHER RELEVANT LAWS AND STNDARDS.

MONDAY, FEBRUARY 15, 2010

WIRING CALCULATIONS FOR SINGLE FAMILY DWELLING UNIT

SINGLE FAMILY DWELLING 
Type of Service - 230 V 
Single Phase 2 wire 60 Hz 
Line to ground Current system 

PROBLEM: 

A single family dwelling is to be circuited with the following requirements as shown on

the figure above. Determine the: 

 size of the branch circuit wire for lighting outlets

 size of the conduit pipes

 size or rating of the fuse protective device

SOLUTION 

A. Circuit - 1 for lighting load 

1. From the Figure above, determine the number of lighting outlets. By direct counting,
there are 8 light outlets. 
The National Electrical Code provides that: 
"100 watts shall be the maximum load for each household lighting outlet." 

Adopting the 100 watts per lighting outlet we have: 

8 outlets x 100 = 800 watts 

2. Determine the Total Current load 

800 watts/230 volts = 3.48 amperes 

3. Determine the size of conductor wire for circuit - 1 . Refer to Table 9.1 or 11.1. use

2 pieces 2.0 mm2 or No. 14 TW copper wire having an ampacity of 15 amperes that
is much largr than the 3.48 amperes computed maximum load. 

4. Determine the size of the Conduit Pipe. Refer to Table . The smallest diameter of a
conduit pipe that could accommodate up to 3 pieces of No.14 TW conductor wire is 13
mm diameter. therefore, specify 13 mm diameter conduit pipe. 

5. determine the size or rating of the fuse protective device. Refer to Table . Use 15
amperes fuse 

The National Electrical Code provides that: 

"Ampacity of the connected load shall not exceed 80% of the amperage
capacity of the conductor and the fuse." 

In Table , the maximum ampacity load of a or 2.0 mm2 No.14 AWG copper wire is 15

amperes. 80 % of 15 is 12, the maximum allowable load of the circuit sufficient enough
to carry the 3.48 amperes computed load for a maximum 100 watts per light outlet.
therefore the use of 2.0 mm2 or No.14 TW is safe. 

B, Circuit - 2 For Small Appliance load 

SOLUTION 

The National Electrical Code provides that: 

"For each single receptacle shall be considered at no less than 180 watts
rating." 

It simply mean that, each convenience outlet, is considered to have a maximum load of
not less than 180 watts per plug or gang. thus: 

1. From Figure above, there are 6 convenience receptacles for small appliance load.
considering that there are two plug outlet, the total number of plug will be: 

6 outlets x 2 plug = 12 pieces 

2. Solve for the Total Estimated Load 

12 x 180 watts per outlet = 2,160 watts 

3. Determine the Maximum Expected Current Load: 

2,160 watts / 230 volts = 9.39 amperes 

4. Determine the Size of the Conductor wire . Refer to Table 9.1 or 11.1. For 9.39
amperes, use 2 pieces 3.5 mm2 or No. 12 TW copper wire for Circuit no.2 

5. Determine the Size of the conduit pipe. for the 2 - No. 12 TW wire, refer to Table .
Use 13 mm conduit pipe. 
6. Determine the Over Current fuse protection. Refer to Table . under the column
of fuse and breaker rating, the 20 amperes fusecan safely carry a maximum load of 16
amperes the 80 % of 20 amperes fuse can safely carry a maximum load of 16 amperes
the 80% of 20 amperes load permitted by the National Electrical Code on No. 12 circuit
wire. 

COMMENT: 

1. On convenience outlet receptacle, the National Electrical Code provides that, " Each
single receptacle shall be considered at no less than 180 watts rating." 

2. Examining the values given on Table , the 2.0 mm2 or No. 14 AWG TW copper wire
has an allowable ampacity rating of 15 amperes. Granting that only 80 % of this 15
amperes is considered the derated value, still 12 amperes is very much larger than the
9.36 amperes computed as maximum load for 6-convenience outlet. Why specify a
bigger 3.5 mm2or No. 12 AWG conductor wire? 

3. Although the 2.0 mm2or No. 14 AWG wire conductor could safely carry the 9.36
amperes computed load, considering its 15 amperes ampacity rating,yet, we cannot do
so because the Code specifically mandated the use of 3.5 mm2or No. 12 AWG copper
wire as the minimum size for all types of convenience outlet wiring except,
for an appliance with limited load wherein a 2.0 mm2or No.14 AWG wire is permitted. 

C. Circuit - 3 for other loads 

SOLUTION 

1. Examining Figure above, other loads are: 

1 - unit electric stove at 1.1 kw = 1,1oo watts 
1 - unit water heater at 2.5 kw = 2,500 watts 
Total Load..........3,600 watts 
2. Compute for the current load. Divide: 

3,600 watts / 230 volts = 15.65 amperes 

3. Determine the size of the service conductor wire. Refer to Table 9.1 or 11.1. 

4. For the 15.65 amperes load, use 2 pieces 3.5mm2or No.12 AWG TW copper
wire 

5. Determine the Size of the Conduit Pipe (if reqd) to Table. Two pieces No. 12 AWG
wire can be accommodated comfortably in a 13 mm diameter conduit pipe. Specify
13 mm diameter conduit pipe. 

6. Determine the size or rating of the Over-current Protection. Refer to Table .

For the 15.65 amperes load use 20 amperes fuse rating. 

COMMENTS: 

The fuse rating is 20 amperes. Granting that it will be derated at 80 % x 20, the 16
amperes derated value is still higher than the computed load of 15.65 amperes.
Therefore, the 20 amperes fuse over current protection is accepted. 

FINDING THE SIZE OF SERVICE ENTRANCE 

The size of service entrance being the supply conductor and equipment for delivering
energy from the electricity supply to the wiring system of the building, is also computed
based on the total load supplied by the branch circuit. Continuing the solution, we have
the following: 

1. Solve for the total load of circuit 1 to circuit 3. 

Total current load = Total connected load / voltage rating 

= (800 W + 2,160 W + 3,600 W) / 230 V 

= 28.52 amperes 

2. Apply 80% demand factor as permitted by the National Electrical Code. 

28.52 x .80 = 22.8 amperes 

3. Find the Size of the Service Wire. Refer 22.8 amperes to Table . Use 2-
8.0 mm2or No.8 TW copper wire 

4. Determine the size of conduit pipe for the service wire. Refer Table , for No.8 TW
copper wire, use 20 mm diameter conduit pipe. 
COMMENT: 

1. A demand factor of 80% was applied considering that not all receptacles and
outlets are being used simultaneously. 

2. These type of loads are classified as non-continuous load. From Table 9.1, the
5.5 mm2or 
No.10 AWG copper wire conductor has 30 amperes ampacity which is bigger than 22.8
amperes as computed. However, we do not specify the use of No.10 AWG wire because
the code limits the use of 8.0 mm2or No.8 AWG, conductor as minimum size
for Service Entrance. 

3. The National Electrical Code on Service Entrance provides that: 

" Service entrance shall have sufficient ampacity to carry the building load. They shall
have the adequate mechanical strength and shall not be smaller than 8.0 mm2or 3.2
mm diameter except for installation to supply limited load of a single branch circuit
such as small poly-phase power, controlled water heaters and the like and they shall
not be smaller than 3.5 mm2or 2.0 mm diameter copper or equivalent. 

THE MAIN DISCONNECTING MEANS OR SAFETY SWITCH 

Find the total computed load 

Circuit - 1 ........ 3.48 amperes 

Circuit - 2 ........9.39 amperes 
Circuit - 3 ........15.65 amperes 
TOTAL........28.52 amperes 

2. Use 2 pieces 30 amperes fuse parallel connection 60 amperes 2 pole single throw
(PST) 250 volts safety switch 

3. Provide 2-double branch circuit cut out with two 15 and 2-20 amperes fuse
respectively. 

MULTI-ground system and line to line service 

The protection of branch circuit is tapped to the hot line of live wire. The grounded line
being in neutral zero voltage is not protected with fuse. this is one advantage of the
MULTI-GROUND SYSTEM being adopted by the electric cooperative implemented by
the RURAL ELECTRIFICATION PROGRAM of the government. The branch circuit and
cutout should be doubled because the engaged voltage in the line is only 230 V while the
other is zero being grounded ( see figure) 

Other electric service system on the other hand, are classified as LINE TO LINE
SERVICE wherein the engaged voltage is 115/230 volts which requires FUSE
PROTECTIO FOR BOTH LINES. 

NOTE: 
The quantity of materials is subject to change depending upon the area and the choice of
the designing engineers. For open onstallation, conduit pipe can be changed to split
knobs or PDX wires. 

SINGLE FAMILY DWELLING 

Type of Service - 115/230 V 
Single Phase 3 wire 60 Hz 
Line to Line system 

SOLUTION: 

Examining the lighting plan of the above figure, there are 19 lighting outlets. Split the 19
outlets into two circuits A and B. 

A. Circuit - 1 Lighting Load (10 light outlets) 

1. The PEC provides that 100 watts be the maximum load per light outlet. thus, for 10
light outlets at 100 watts, multiply: 

10 outlets x 100 watts = 1000 watts 

2. Compute The Current Load 

1000 watts/230 volts = 4.35 amperes 

3. Find the size of Branch circuit wire. Refer to Table 9.1 or 11.1. For 4.35 amperes,
use 2.0 mm2 TW copper wire. 
4. Find the rating of overcurrent protection. Refer to Table. for 4.35 A, use 15
amperes trip breaker. 

5. Determine the size of conduit pipe. Refer to Table , for No. 14 TW copper wire,
use 13 mm conduit pipe. 

B. Circuit - 2 Lighting Load (9 light outlets) 

1. For 9 outlets, find the Total load in watts. 

9 outlets x 100 watts per outlet = 900 watts 

Divide : 900 watts/230 volts = 3.91 amperes 

2. Determine the Size of the Branch circuit Wire. Refer to Table 9.1 or 11.1. For 3.91
A load, use 2.0 mm2or No.14 TW copper wire. 
3. Determine the size of the conduit pipe. Refer to Table. For 2 pieces No. 14 TW
copper wire, use the 13 mm minimum size of conduit pipe. 
4. Determine the size or rating of the overcurrent Protection. Refer to Table. For
3.91 A load, use 15 A load fuse of trip breaker. 
C. Circuit - 3 For small appliance load 

Section 3.3.1.2 of the the PEC specif 180 watts load limit per convenience outlet. Thus, 

1. Find the number of appliance load outlet and the current load. 

6 outlets x 2 gang per outlet x 180 watts 

12 x 180 = 2,160 watts 
Divide: 2160 watts/230 volts = 9.39 A 

2. Determine the Size of the Service Wire conductor. Refer to Table 9.1 or 11.1. For
the 9.39 A load, specify the minimum wire gauge for convenience outlet. 

2 pieces 3.5 mm2or No.12 TW copper wire 

3. Determine the Size of the conduit pipe. Refer to Table. For 2 pieces No.12 TW

copper wire. Use 13 mm diameter conduit pipe. 
4. Solve for the Size or Rating of the Over current Protection. Refer to Table. For
9.39 A on No. 12 TW copper wire specify: 
20 A fuse or trip breaker. 

D. Circuit- 4 for Small Appliance Load 

1. The load of circuit 4 is identical with circuit . Use the same size of wire, conduit, and
wire protection rating. 
E. Circuit - 5 for Range Load 

1. Range load (appliance rating) at 8.0 kW = 8000 watts 

2. Solve for the Line current. 

8000 watts / 230 V= 34.78 A 

3. Refer to Table , apply 80% demand load factor . 

34.78 x .80df = 27.82 A 

4. Determine the Size of the Branch Circuit wire. Refer to Table 9.1 or 11.1. For the
27.82 A, use 8.0 mm2 or No. 8 TW copper wire. 

5. Determine the Size of Conduit pipe. Refer to Table. For 2 pieces No.8 wire
use 200 mm diameter pipe. 

6. Find the Size or Rating of the Fuse or Trip Breaker. Refer to Table. For
appliance load, use 40 A fuse or trip breaker. 

F. Circuit - 6 for Water heater Load 

1. one unit water heater at 2.5 kW = 2500 watts 

2. The current load will be: 

2500 watts/230 volts = 10.86 A 

3. Solve for the Size of the Branch circuit wire. Refer to Table 9.1 or 11.1 . For 10.86
A convenience outlet use 2 pcs 3.5 mm2 or No. 12 TW copper wire. 
4. Determine the Size of the conduit pipe. Refer to Table. For 2 - No.12 Tw copper
wire, use 13 mm conduit pipe. 
5. Find the Size or Rating of the Over Current Protection. For the 10.86 A load,
use 20 A fuse fuse or trip breaker. 

G. Circuit 7 and 8 with 1 - unit ACU each 

1. One unit ACU at 1.5 Hp is 

1.5 Hp x 746 = 1119 watts 

Article 6.7 of the Philippine Electrical Code provides that: "BRANCH CIRCUIT
CONDUCTOR SUPPLYING A MOTOR SHALL HAVE AN AMPACITY NOT LESS THAN
125% OF THE FULL LOAD CURRENT."

2. Current Load: 1119 watts/230 V = 4.86 A 

4.86 A x 125% = 6.07 A 

3. Find the Size of the Branch circuit service wire. Refer to Table. The 6.7 A can be
served by a 2.0 No.14 TW copper wire, but the Code limits the size of convenience outlet
to No. 12 AWG copper wire. Specify No.12 THW copper wire for circuit 7 and 8. 
4. Find the Size of the conduit pipe. Refer to Table. For two No.12 wire, use 13 mm
conduit pipe. 

5. Find the Size and Rating of the Branch Circuit Protection. The Code on
branch circuit protection for a single motor provides that" It shall be increased by 250%
of the full load current of the motor." thus, 

4.86 x 250% = 12.15 A. From Table for a continuous load use 2-30 AT breaker. 

CALCULATING THE AMPACITY OF THE SERVICE 

ENTRANCE CONDUCTOR AND THE MAIN DISCONNECTING MEANS 

1. Find The total current load of circuit 1 to circuit 8: 

lighting load Ct. 1 and Ct.2 ....................1900 watts 

small appliance load Ct. 3 and Ct. 4.......4320 watts 
other loads Ct.5 and Ct 6.,......................10500 watts 

TOTAL LOAD(except the ACU)....16720 watts 

2. From Table , OPTIONAL CALCULATION for dwelling Unit, apply demand factor. 

for the first 10000 w at 100%(df)...........10000 watts 

subtract: 16720 - 10000 = 6720 watts 

for other load, multiply by 40% 

6720 x .4 .........................................2688 watts 

Aircon unit at 100% demand factor 

2-units at 1119 watts........................2238 watts 

TOTAL .....................14, 926 watts 

TOTAL CONNECTED LOAD PLUS 25% OF THE LARGEST MOTOR 

1. Ampere I = 14.926w + (25% of 1.119w)/230 V 

= 63.37 A 
2. Find the Size of Main feeder and the Neutral line. 
- Use 2 - 3.8 mm2 TW copper wire 

3. The Neutral Conductor of a 3 - wire line to line supply system shall have an

ampacity of not less than 70% of the ungrounded(live wire) conductor or TWO TRADE
SIZE SMALLER SIZE THAN THE UNGROUNDED CONDUCTOR. (PEC specs)
Therefore use 1- 22 mm2 Tw copper wire for the Neutral line. 

4. Determine the Size of the Conduit pipe. Refer to Table , use 32 mm diameter

pipe. 

5. For main Breaker, refer to Table . Use 2 - 100 A 2 - wires 250 V, 2 pole molded
air circuity breaker. 

COMMENT: 

The total computed load is 63.37 A. The 30 mm2 copper wire could be used considering
its 90 A capacity. However, The NEC provides that: 

" If the computed load exceeds 10000 watts, the conductor and overcurrent protection
shall be rated not less than 100 A. 

THEREFORE USE 2 - 38 mm2 TW WIRE FOR THE MAIN FEEDER AND 2 -

100 A FOR THE MAIN BREAKER. 

Small Family Dwelling 

Type of Service - 230 volts; two wire 
Line to Ground system 

A single family dwelling with a floor area of 80 square meters has the following
receptacles and outlets load. 

LIGHTING: 

7 pcs. - 40 watts fluorescent lamps 

2 pcs. - 20 watts Incandescent lamps 

CONVENIENCE OUTLET: 

1 - Electric Iron .............................................. 1000 watts 

1 - Electric stove.............................................. 1100 watts 
2 - Electric fan ................................................ 500 watts 
1 - 7 cu. ft Refrigerator .................................... 175 watts 
1 - Portable stereo ........................................... 100 watts 
1 - 20" TV set ................................................... 300 watts 

SOLUTION: 

A. Circuit 1 - Lighting Load by the Area method 

1. Determine the wattage required per square meter area. From, the wattage required
per square meter for dwelling units is 24 watts. Multiply: 

80 sq.m x 24 watts = 1920 watts 

2. Determine the current load. Divide: 

1920 watts/ 230 volts = 8.35 A 

3. Compute the actual lighting load. Multiply: 

7 - Fluorescent lamps x 40 watts = 280 watts 

2 - Incandescent bulb x 60 watts = 120 watts 
TOTAL............ 400 watts 

4. Solve the actual current load. Divide: 

400 watts/230 volts = 1.74 A 

5. Determine th Size of the Branch Circuit wire. From , the 1.74 A is very small load
to be carried by 2.0 mm2 or No. 14 TW copper wire. Therefore, the No. 14 wire is
safe. 

6. Determine the Size of the conduit pipe. Refer to table, for 2- No.14 wire, use 13
mm conduit pipe. 

7. Determine the size or rating of the branch circuit protection. Refer to table.

For 2.0 mm2 or No.14 copper wire conductor, use 15 A fuse or trip breaker. 

B. Circuit - 2 For small appliance load 

1. Solve for the total appliance current load. 

LOAD CURRENT = ( 1000 + 1100 + 500 + 175 + 300 + 100) / 230 volts  
= 3175 watts/230 volts 
= 13.81 A 

2. Determine the size of the Branch circuit wire conductor. Refer to Table. For a
convenience load of 13.81 A specify 3.5 mm2 or No. 12 TW copper wire, the
minimum size required for convenience outlet. 

3. Find the size of the conduit pipe. Refer to Table, for 2 pieces No.12 TW copper
wire, use 13 mm diameter pipe. 
4. Find the Size or rating of the Protection device. See Table, for 13.81 A, use 1 -
20 A fuse. 

COMMENT: 

It is interesting to note that only one 20 A fuse protection was used because the current
is a LINE TO GROUND OR MULTI-GROUND SYSTEM where one line is zero voltage
being grounded. Unlike the LINE TO LINE SYSTEM of current supply, it is necessary to
provide 2 fuses to protect the two line branch circuit. 

FINDING THE SIZE OF THE SERVICE ENTRANCE OR FEEDER 

1. Get the sum total of connected load. Add: 

Lighting Load.................................... 1920 watts 

Small appliance load ......................... 3175 watts 
TOTAL.................................. 5095 watts 

2. Solve for the total connected load current. Divide: 

5095 watts/230 volts = 22.15 A 

3. Find the size of Service Entrance. Refer to Table. For 22.15 A, use No. 8 TW

copper wire, the minimum size for service entrance. 

4. For Main Protection, use 1-safety switch, 2 pole, 2 wires, 250 volts. 

Under the preceding set-up, one safety switch could supply both lighting and
convenience outlet at different branch circuit without the use of fuse cutout. This is only
applicable to the line to ground or multi-ground system being used by the electric
cooperative. 

POSTED BY ELECTRICAL DESIGN1 AT 10:07 PM 

LABELS: C. WEEK 4 AND 5

20 COMMENTS:

1.

Kim JoseMarch 29, 2013 at 6:22 AM

what is the distance between each convenience outlet? and the distance
from the floor to the convenience outlet?

Reply

Replies

1.

UnknownJune 23, 2018 at 6:45 PM

Evry 3m less for distance of each oulet ... and height of

convenience outlet from finish floor.level , 450mm

Reply

2.

Roel BobisJuly 29, 2014 at 11:09 PM

This is very helpful specially circuit breaker here in the Philippines

Reply

3.

Jayson CidNovember 27, 2014 at 3:50 AM

how do you got the 63.37amp. for your service entrance wire

Reply

4.

atocruzMay 5, 2015 at 6:01 PM

 This is one of the best samples....Thank you!

Reply

5.

John Ray SaysonOctober 20, 2015 at 9:32 PM

thanks for the info.. but where can i find those tables??

Reply

6.

John Ray SaysonOctober 20, 2015 at 9:33 PM

thanks for the info.. but where can i find those tables??

Reply

7.

John Ray SaysonOctober 20, 2015 at 9:33 PM

thanks for the info.. but where can i find those tables??

Reply

8.

Jenny HayesJanuary 22, 2016 at 1:41 AM

I just want you to know that your blog is perfectly

nice. www.wesbellwireandcable.com/

Reply

9.

Patricio PantheleonMarch 29, 2016 at 8:25 PM

 thanks for the info. I would like to recommend Panther.ph for your
electrical supply needs.

Reply

10.

mikael zabalaJune 24, 2016 at 6:46 AM

Nice

Reply

11.

arnel luarezAugust 24, 2016 at 9:51 PM

Ty.

Reply

12.

Edgar DampiosApril 20, 2017 at 7:34 PM

The National Electrical Code set 100 watts as the max. for lighting, why we
need to use 100 in the computation of total watts, what if I'm using 20 pcs.
of 5W LED bulb, is using 100 as multiplier, it is not an over design? as the
actual is only 100W not 2000W

Reply

13.

Medz RamirezSeptember 17, 2017 at 11:49 PM

WHAT IS THE DEMAND FACTOR FOR A SIMPLE STUDIO TYPE

APARTMENT. TOTAL WATTAGE IS 3480 WATTS PER UNIT

Reply

Replies
 1.

Charles Ryan VillanuevaDecember 19, 2017 at 12:06 AM

How many units?

Reply

14.

Medz RamirezSeptember 17, 2017 at 11:52 PM

5-small appliance duplex outlets, 3- light bulbs and 1-1hp ACU. of the total
wattage, what will be the demand factor? hope to hear from you and it will
be greatly appreciated if someone share their knowledge on this matter

Reply

15.

Shanaiah JanosDecember 6, 2017 at 2:22 PM

Why not use a THHN wire?

Is TW more ideal?

Reply

Replies

1.

Charles Ryan VillanuevaDecember 19, 2017 at 12:08 AM

TW is a minimum requirement. THHN is better.

Reply

16.

UnknownDecember 19, 2017 at 12:04 AM

This comment has been removed by the author.

 Reply

17.

Adrian SantosFebruary 1, 2018 at 4:26 PM

Hi sir. In a standard circuit of LP how many lights is the limit per circuit?
and Where can I find it in PEC.
Thanks.

Reply
Newer PostOlder PostHome

Subscribe to: Post Comments (Atom)

LABELS

 A. week1 (1)
 B.week 2 and 3 (1)
 C. week 4 and 5 (1)
 D. week 6 and 7 (1)
 E. week 8 and 9 (1)
 F. week 10 and 11 (1)
 G. week 12 (1)
 H. week 13 (1)
 I. week 14 (1)

BLOG ARCHIVE

 ▼  2010 (9)
o ▼  February (9)
 TERM TEST
 COST ESTIMATION
 ELECTRIC MOTOR AND OVERCURRENT PROTECTION
 ILLUMINATION CALCULATION AND DESIGN FOR MULTI-
FAMI...
 WIRING CALCULATION FOR MULTI-FAMILY DWELLING
 ILLUMINATION CALCULATION AND DESIGN FOR SINGLE
FAM...
 WIRING CALCULATIONS FOR SINGLE FAMILY DWELLING
UNI...
 PEC REQUIREMENTS FOR ADEQUATE WIRING IN SINGLE
AND...
 BASIC CONCEPT IN ELECTRICAL DESIGN
 

SEARCH THIS BLOG

Search

Blogger Templates by Wishafriend.com